Carbon Nanotubes as Catalyst Support - Hyperion Catalysis as Support.pdf · Carbon Nanotubes as Catalyst Support Jun Yang, Jun Ma ... Preparation of Rigid Porous Carbon Nanotube Granules

Carbon Nanotubes as Catalyst Support

Jun Yang, Jun MaHyperion Catalysis International, Inc.

38 Smith Place, Cambridge, MA 02138

OutlineBackgroundPhysical Properties of Hyperion FIBRILTM

NanotubesFunctionalization of Carbon NanotubesPreparation of Rigid Porous Carbon Nanotube GranulesApplication of FIBRIL Nanotubes as Catalyst SupportSummary

BackgroundActivated Carbon as Catalyst Support

Advantages:• Resistance to acid/basic media• Possibility to control porosity and surface chemistry• Chemical inertness• Easy recovery of precious metal• Large specific surface area, easy to obtain.

Disadvantages:• Narrow microporosity (< 2nm)• Derived from natural resources → inconsistent

quality, traces of impurities• Low mechanical and thermal stability

Compared to activated carbons:

• Mesoporosity (2-50nm) → improves mass

transfer

• High purity → avoids self-poisoning

• Consistent material

• High mechanical and thermal stability

Carbon Nanotubes(CNTs) as Catalyst Support

CNTs as Catalyst Support (cont.)

Challenges:• Controlling surface chemistry of CNTs →

functionalization of CNTs

• Increasing mechanical strength of CNT aggregates → preparation of rigid porous CNT granules

• Maintaining the unique properties of CNTs, especially the mesoporosity

Physical Properties of Hyperion FIBRIL Nanotubes

Morphology of as-made HyperionFIBRIL NanotubesOD: 8-15nm, Length: 1-100µm

100 nm

Porosity of as-made Hyperion FIBRIL Nanotubes

2.010.03240

Meso-Micro-

Pore Volume (cm3/g)BET (m2/g)

Measured by N2 adsorption at 77K

Functionalization of CNTs

0.160.380.761.01Titer (meqv/g)

H2O2H2O2-WO3(NH4)2S2O8/

H2SO4

Nitric AcidOxidant

Preparation of Rigid Porous CNTs Granules

Methods:• Direct extrusion of functionalized CNTs• Extrusion with addition of binder

Crush Strength: 1/8” OD cylinder

61.338.9Crush strength (lb/in)

With binderDirectExtrusion

Photograph of FIBRIL Nanotube Powdersand Extrudates

Pore Volume

1.400.012441.7Extrudates

2.010.032400Powders

(cm3/g)(cm3/g)(m2/g)(wt%)

Mesopore volume

Micropore volume

Surface area

Binder residueSample

Porosity of Extrudates with Addition of Binder

10 100 1000 10000Pore diameter [Å]

Dv(

d) [m

l/Å/g

]

PowdersExtrudates

• Pore size distribution

Application as Catalyst Support

2.544.652.251.63

2.055.60.21.957.80.51.959.61

5.619.920

Particle size* (nm)Dispersion* (%)Loading (wt%)

CNT Supported Pd Catalysts#

#: prepared by impregnation*: apparent Pd dispersions and particle size were measured

by CO chemisorption at RT, and assuming CO:Pd=1

TEM of Pd/CNT Catalysts

1wt%Pd/CNT

5wt%Pd/CNT

20 nm

Comparison of CNT with Activated Carbon as Support

1.012.15Titer (meqv/g)

55Pd Loading (wt%)

2.54.3Pd Particle Size (nm)

HNO3HNO3Functionalization

150-300150-300Granule Size (µm)

44.625.8Pd Dispersion (%)

CNTActivated CarbonSupport

H2

RT

(Gas-Liquid-Solid)

NO2 NH2

• Hydrogenation of Nitrobenzene

0102030405060708090

100

0 50 100 150 200 250 300Time on stream (min)

Con

vers

ion

(%) Pd/CNT

Pd/C

50mg of catalyst in 100ml of 5vol% nitrobenzene/2-propanol solution

Comparison of Pd/CNT with Commercial Pd/C Catalyst

PelletsGranulesAppearance

1.92.1Pd Particle Size (nm)

0.50.5Pd Loading (wt%)

420-840420-840Granule Size (µm)

58.554.3Pd Dispersion (%)

Pd/CNTPd/C (PMC)Catalyst

H2

25°C(Gas-Solid)

• Hydrogenation of Cyclohexene

0102030405060708090

100

0 100 200 300 400Time on stream (min)

Con

vers

ion

(%)

Pd/CNT

Pd/C

Summary

Successfully demonstrate . . .• Control of surface chemistry by CNT

functionalization• Preparation of rigid porous CNT granules• Conservation of CNT mesoporosity in extrudates

FIBRIL nanotubes are promising as catalyst support