Page 1
GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORSGROUP
has been assessed and accredited in accordance with the standard
ISO/IEC 17025:2017''General Requirements for the Competence of Testing &
Calibration Laboratories''for its facilities at
PLOT NO. 126, POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
in the field of
CALIBRATIONCertificate Number: CC-2205
Issue Date: 17/01/2020 Valid Until: 17/05/2021
This certificate remains valid for the Scope of Accreditation as specified in the annexure subject to continuedsatisfactory compliance to the above standard & the relevant requirements of NABL.
(To see the scope of accreditation of this laboratory, you may also visit NABL website www.nabl-india.org)
Signed for and on behalf of NABL
N. VenkateswaranChief Executive Officer
Page 2
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
Permanent Facility
1 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current 1 kHz 100 µA to 200 µA 0.26% to 0.39% Using 6 ½ DigitMultimeter 8846A byDirect Method
2 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current 50 Hz 10 A to 3200 A 0.4% Using Standard CurrentTransformer with 6 ½Digit Multimeter 8846Aby Direct Method
3 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current 50 Hz to 1kHz
0.2 mA to 100 mA 0.39% to 0.18% Using 6 ½ DigitMultimeter 8846A byDirect Method
4 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current 50 Hz to 1kHz
100 mA to 10 A 0.18% to 0.29% Using 6 ½ DigitMultimeter 8846A byDirect Method
5 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Current 1 kHz to 5kHz
3 mA to 3 A 0.16% to 3.54% Using Multi ProductCalibrator 5502A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 1 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 3
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
6 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Current 50 Hz 20 A to 1000 A 0.79% Using MPF 5502 A withCurrent Coil by DirectMethod
7 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Current 50 Hz to 1kHz
10 A to 20 A 0.17% to 0.36% Using Multi ProductCalibrator 5502A byDirect Method
8 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Current 50 Hz to 1kHz
3 A to 10 A 0.16% to 0.17% Using Multi ProductCalibrator 5502A byDirect Method
9 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Current 50 Hz to 1KHz
30 uA to 3 mA 1.44% to 0.16% Using Multi ProductCalibrator 5502A byDirect Method
10 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 10 uA to 100 mA 0.36% to 0.064% Using 6 ½ DigitMultimeter 8846A byDirect Method
11 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 100 mA to 3 A 0.064% to 0.19% Using 6 ½ DigitMultimeter 8846A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 2 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 4
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
12 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 3 A to 10 A 0.19% Using 6 ½ DigitMultimeter 8846A byDirect Method
13 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Current 10 µA to 100 µA 0.26% to 0.044% Using Multi ProductCalibrator 5502A byDirect Method
14 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Current 100 uA to 3 mA 0.044% to 0.031% Using Multi ProductCalibrator 5502A byDirect Method
15 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Current 20 A to 1000 A 0.64% Using MPF 5502 AWith Current Coil byDirect Method
16 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Current 3 A to 20 A 0.11% to 0.38% Using Multi ProductCalibrator 5502A byDirect Method
17 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Current 3 mA to 3 A 0.031% to 0.11% Using Multi ProductCalibrator 5502A byDirect Method
18 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
CurrentTransformer(PhaseError)5A (Secondary)1% to 120% of ratedcurrent
1 A to 3200 A 3.34min Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
19 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
CurrentTransformer(RatioError)5A (Secondary)1% to 120% of ratedcurrent
1 A to 3200 A 0.047% Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 3 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 5
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
20 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
AC HIGH VOLTAGE 1 kV to 40 kV 3.2% Using HV Divider withKV Meter
21 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
AC High Voltage 50 Hz 1 kV to 5 kV 3.2% to 3.8% Using Udeyraj makeHV Divider withindicator by DirectMethod
22 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
AC High Voltage 50 Hz 5 kV to 25 kV 3.8% to 3.2% Using Udeyraj makeHV Divider withindicator by DirectMethod
23 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
AC Voltage 1 kHz 1 mV to 20 mV 4.72% to 0.33% Using 6 ½ DigitMultimeter 8846A byDirect Method
24 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
AC Voltage 50 Hz to 1kHz
20 mV to 1000 V 0.54% to 0.10% Using 6 ½ DigitMultimeter 8846A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 4 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 6
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
25 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Phase Error)1A(Secondary)From 1%to 120% of ratedcurrent
1 A to 3200 A 3.36min Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
26 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Phase Error)1A/5ASecondary from 1% to120% of rated current
2000 A to 7500 A 3.4min Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
27 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Phase Error)5A (Secondary)From 5% to120% of rated current
3000 A to 6000 A 3.36min Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
28 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Phase Error)5A(Secondary)From 1%to 5% of rated current
3000 A to 6000 A 3.36min Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
29 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Ratio Error)1A(Secondary)From 1%to 120% of ratedcurrent
1 A to 3200 A 0.05% Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 5 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 7
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
30 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Ratio Error)1A/5ASecondary from 1% to120% of Rated Current
2000 A to 7500 A 0.085% Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
31 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Ratio Error)5A (Secondary)From 5% to120% of rated current
3000 A to 6000 A 0.1% Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
32 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Ratio Error)5A(Secondary)From 1%to 5% of rated current
3000 A to 6000 A 0.1% Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
33 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC High Voltage 1 kV to 5 kV 3.2% Using Udeyraj makeHV Divider withindicator by DirectMethod
34 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC High Voltage 5 kV to 25 kV 3.2% Using Udeyraj makeHV Divider withindicator by DirectMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 6 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 8
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
35 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC Resistance 1 mOhm to 1 Ohm 0.42% to 0.36% Using 6 ½ DigitMultimeter 8846A byV/I Method
36 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC Resistance 1 MOhm to 1000MOhm
0.013% to 2.31% Using 6 ½ DigitMultimeter 8846A byDirect Method
37 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC Resistance 1 Ohm to 1 MOhm 0.36% to 0.013% Using 6 ½ DigitMultimeter 8846A byDirect Method andVoltage/ CurrentMethod
38 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC Voltage 1 mV to 100 mV 0.42% to 0.085% Using 6 ½ DigitMultimeter 8846A byDirect Method
39 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC Voltage 100 mV to 1000 V 0.085% to 0.007% Using 6 ½ DigitMultimeter 8846A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 7 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 9
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
40 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Potential Transformer(Phase Error)
11000/110 4.03min Using StandardPotential transformer &Instrument transformertest set up ByComparison Method
41 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Potential Transformer(Phase Error)
11000/63.5 3.16min Using StandardPotential transformer &Instrument transformertest set up ByComparison Method
42 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Potential Transformer(Ratio Error)
11000/110 0.16% Using StandardPotential transformer &Instrument transformertest set up ByComparison Method
43 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Potential Transformer(Ratio Error)
11000/63.5 0.16% Using StandardPotential transformer &Instrument transformertest set up ByComparison Method
44 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Voltage Ratio 0.8 to 2021 ratio 0.16% Using 6 ½ DigitMultimeter 8846A andFluke 5502A by DirectMethod
45 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Power 50 [email protected] UPF 120/2240 V 0.1A to 20 A
1.2 W to 4800 W 3.47% to 0.23% Using Multi ProductCalibrator 5502A withPower Option by DirectMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 8 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 10
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
46 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Vertical deflectionHorizontal Deflection 1kHz
5m V to 50 V 2.64% to 0.40% Using Multi ProductCalibrator 5502A withScope Option by DirectMethod
47 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Voltage 1 kHz 2 mV to 10 mV 1.76% to 0.41% Using Multi ProductCalibrator 5502A byDirect Method
48 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Voltage 1 kHz to 10kHz
30 V to 1000 V 0.1% Using Multi ProductCalibrator 5502A byDirect Method
49 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Voltage 50 Hz to 1kHz
10 mV to 300 mV 0.41% to 0.044% Using Multi ProductCalibrator 5502A byDirect Method
50 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Voltage 50 Hz to 1kHz
300 mV to 300 V 0.044% to 0.1% Using Multi ProductCalibrator 5502A byDirect Method
51 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Voltage 50 Hz to 1kHz
300 V to 1000 V 0.1% Using Multi ProductCalibrator 5502A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 9 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 11
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
52 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Capacitance @ 1 kHz 10 pF to 1 nF 2.98% to 1.2% Using DecadeCapacitance Box &Multi Product Calibrator5502A by DirectMethod
53 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Capacitance @1 kHz 9 nF to 1 mF 1.26% to 0.80% Using DecadeCapacitance Box &Multi Product Calibrator5502A by DirectMethod
54 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Capacitance @1kHz 1 nF to 9 nF 1.7% to 1.26% Using DecadeCapacitance Box &Multi Product Calibrator5502A by DirectMethod
55 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Power @ 1 V to600 V, 1A to 20 A
1 W to 12 KW 0.37% to 0.25% Using MultiproductCalibrator 5502A withPower Option by DirectMethod.
56 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Resistance 1 mohm to 1 mohm 0.6% to 0.6% Using Shunt By DirectMethod
57 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Resistance 1 Ohm to 100 Ohm 0.25% to 0.072% Using Multi ProductCalibrator 5502A byDirect Method.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 10 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 12
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
58 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Resistance 100 kOhm to 100MOhm
0.021% to 0.58% Using Multi ProductCalibrator 5502A byDirect Method
59 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Resistance 100 ohm to 100 kOhm 0.072% to 0.021% Using Multi ProductCalibrator 5502A byDirect Method
60 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Voltage 1 mV to 100 mV 0.36% to 0.013% Using Multi ProductCalibrator 5502A byDirect Method.
61 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Voltage 100 mV to 30 V 0.013% to 0.0064% Using Multi ProductCalibrator 5502A byDirect Method.
62 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Voltage 30 V to 1000 V 0.0064% to 0.007% Using Multi ProductCalibrator 5502A byDirect Method.
63 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
High Resistance 100 kohm to 1 Tohm 1.2% to 2.4% Using DecadeResistance Box byDirect Method
64 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Inductance @1 kHz 1 mH to 10 H 1.53% to 2.03% Using DecadeInductance Box byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 11 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 13
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
65 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
ODD Harmonics(Current) upto 41st
100 mA to 6 A 0.75% Using FlukeMultiProduct Calibrator5502A
66 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
ODD Harmonics upto41st Voltage
100 mV to 60 V 0.75% Using FlukeMultiproduct Calibrator5502A
67 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Oscilloscope DCFunction
2 mV to 33 V 6.59% to 0.33% Using Multi ProductCalibrator 5502A withScope Option by DirectMethod
68 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Power Factor 50 Hz 0.1 to UPF 0.05PF Using Multi ProductCalibrator 5502A withPower Option by DirectMethod
69 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Voltage ratio 0.8 to 400 0.5% to 0.3% Using TransformerRatio Standard byComparison Method
70 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Voltage Ratio 400 to 2021 0.5% to 0.3% Using TransformerRatio Standard byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 12 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 14
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
71 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -RTD(Calibration oftemperature Indicator /Controller/ Recorder/Calibrator)
(-)200 °C to 800 °C 0.51°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
72 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)C-Type
0 °C to 2315 °C 1.4°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
73 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)E-Type
(-)270 °C to 1300 °C 0.37°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
74 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)J-Type
(-)200 °C to 1200 °C 0.35°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 13 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 15
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
75 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)K-Type
(-)250 °C to 1137 °C 0.47°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
76 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)L-Type
(-)200 °C to 600 °C 0.37°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
77 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)N-Type
(-)270 °C to 1300 °C 0.47°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
78 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)R-Type
(-)50 °C to 1767 °C 0.9°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 14 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 16
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
79 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)S-Type
(-)50 °C to 1767 °C 0.8°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
80 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)T-Type
(-)270 °C to 400 °C 0.35°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
81 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)U-Type
(-)200 °C to 600 °C 0.5°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
82 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -RTD(Calibration oftemperature Indicator /Controller/ Recorder/Calibrator)
(-) 200 °C to 800 °C 0.27°C Using Multi ProductCalibrator 5502A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 15 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 17
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
83 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)EType
(-)200 °C to 1000 °C 0.55°C Using Multi ProductCalibrator 5502A byDirect Method
84 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)JType
(-)210 °C to 1200 °C 0.37°C Using Multi ProductCalibrator 5502A byDirect Method
85 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)KType
(-)200 °C to 1372 °C 0.51°C Using Multi ProductCalibrator 5502A byDirect Method
86 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)NType
(-)200 °C to 1300 °C 0.61°C Using Multi ProductCalibrator 5502A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 16 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 18
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
87 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)RType
0 °C to 1700 °C 0.51°C Using Multi ProductCalibrator 5502A byDirect Method
88 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)SType
0 °C to 1700 °C 0.58°C Using Multi ProductCalibrator 5502A byDirect Method
89 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)TType
(-)200 °C to 400 °C 0.70°C Using Multi ProductCalibrator 5502A byDirect Method
90 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)UType
(-)200 °C to 600 °C 0.65°C Using Multi ProductCalibrator 5502A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 17 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 19
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
91 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)BType
600 °C to 1820 °C 0.55°C Using Multi ProductCalibrator 5502A byDirect Method
92 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)CType
200 °C to 2315 °C 0.95°C Using Multi ProductCalibrator 5502A byDirect Method
93 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Frequency 10 Hz to 1 MHz 0.084% to 0.014% Using 6 ½ DigitMultimeter 8846A byDirect Method
94 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Time 0.1 sec to 1 hr 0.013sec to 2.32sec Using Digital TimeInterval Meter By DirectMethod
95 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Time 1 hr to 24 hr 2.32sec to 5.18sec Using Digital TimeInterval Meter Bycomparison Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 18 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 20
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
96 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Bandwidth 50 MHz to 250 MHz 6.21% Using Multi ProductCalibrator 5502A withScope Option by DirectMethod
97 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Frequency 10 Hz to 300 kHz 0.086% to 0.0094% Using Multi ProductCalibrator 5502A byDirect Method
98 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Frequency 300 kHz to 2 MHz 0.0094% to 0.49% Using Multi ProductCalibrator 5502A byDirect Method
99 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Time Base 2 n Sec to 5 Sec 0.3% to 0.67% Using Multi ProductCalibrator 5502A withScope Option by DirectMethod
100 MECHANICAL-ACCELERATION ANDSPEED
Speed RPM - (Non-Contact)
10 RPM to 5000 RPM 2.1RPM Using Tachometer.
101 MECHANICAL-ACCELERATION ANDSPEED
Speed RPM - (Non-Contact)
5000 RPM to 30000RPM
19RPM Using Tachometer.
102 MECHANICAL-ACOUSTICS
Acoustic Pressure -Sound Level Meter @ 1kHz
114 db 1.1db Using Sound LevelCalibrator.
103 MECHANICAL-ACOUSTICS
Acoustic Pressure -Sound Level Meter @ 1kHz
94 db 0.96db Using Sound LevelCalibrator.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 19 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 21
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
104 MECHANICAL-DENSITY ANDVISCOSITY
Hydrometer - DensityHydrometer, TwaddleHydrometer, BaumeHydrometer, SpecificGravity Hydrometer,BrixHydrometer,Lactometer, Alcometer.
0.6 g/ml to 2.000 g/ml 0.00025g/ml Using WeighingBalance with resolution0.01 mg by Hydrostaticweighing method asper NISP SP 250-78Standard.
105 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Bevel ProtractorL.C.: 1' 0 ° to 360 ° 3.1arc min Using Angle GaugeBlock & Surface Plate.
106 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Bore Gauge(Transmission Only)L.C.: 1 µm
Up to 1 mm 3.1µm Using Dial CalibrationTester.
107 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Caliper(Vernier/Dial/Digital)L.C.:10 µm
1000 mm to 2000 mm 22.5µm Using Caliper Checker;Gauge Block; LengthBar & ExternalMicrometer.
108 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Caliper(Vernier/Dial/Digital)L.C.:10 µm
0 to 1000 mm 14µm Using Caliper Checker;Gauge Block; LengthBar & ExternalMicrometer.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 20 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 22
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
109 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Caliper(Vernier/Dial/Digital)L.C.:10 µm
0 to 600 mm 10µm Using Caliper Checker;Gauge Block; LengthBar & ExternalMicrometer.
110 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Coating ThicknessGauge(Digimatic/Analog)L.C.:0.1 µm
0 to 6 mm 3.55µm Using Thickness Foils.
111 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Comparator Stand 300 mm to 300 mm 3.7µm Using Gauge Block;Elec. Probe & SurfacePlate.
112 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Cube Mould 0 to 300 mm, 0 to 360° 16.8 µm, 3.6 min Using Profile Projector& Digital Verniercaliper, BevelProtractor byComparison Method
113 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Cylindrical MeasuringPin
0.5 mm to 25 mm 1.3µm Using Gauge Block Set& Electronic Probe.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 21 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 23
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
114 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Cylindrical SettingMasterDiameterVariation
>100 mm to 160 mm 3.3µm Using Gauge Block Set& Electronic Probe
115 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Cylindrical SettingMasterDiameterVariation
Up to 100 mm 2.8µm Using Gauge Block Set& Electronic Probe.
116 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Degree Protractor /Combination Set L.C.:1°
0 ° to 360 ° 20arc min Using Slip GaugeBlock, Sine Bar; AngleGauge Block & SurfacePlate.
117 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Depth Caliper(Vernier/Dial/Digital)L.C.: 10 µm
0 to 300 mm 8µm Using Gauge Block;Long Gauge Block &Surface Plate
118 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Depth MicrometerL.C. :1 µm
0 to 300 mm 4.0µm Using Gauge BlockSet; Long Gauge Block& Surface Plate.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 22 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 24
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
119 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial CalibrationTesterL.C.: 0.1 µm
0 to 25 mm 1.12µm Using Electronic Probe
120 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial ComparatorL.C.:0.5 µm
-50 µm to 50 µm 1.5µm Using Gauge Block Set& Comparator Stand.
121 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial ThicknessGaugeL.C.: 1 µm
0 to 10 mm 0.8µm Using Gauge BlockSet.
122 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial ThicknessGaugeL.C.: 10 µm
0 to 100 mm 8µm Using Gauge BlockSet.
123 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
ElectronicComparatorL.C.: 0.1µm
0 to 25 mm 0.9µm Using Gauge BlockSet.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 23 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 25
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
124 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Electronic HeightGaugeL.C.: 0.5 µm
0 to 600 mm 8µm Using Gauge Block;Long Gauge & SurfacePlate.
125 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(Analog/Dial/Digital)L.C.: 1 µm
>25 mm to 300 mm 4.0µm Using Gauges BlockSets; Long GaugeBlock & Mic Check Set.
126 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(Analog/Dial/Digital)L.C.: 1 µm
0 to 25 mm 0.8µm Using Mic.Check Set.
127 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(Analog/Dial/Digital)L.C.: 10 µm
>300 mm to 600 mm 12.9µm Using Gauges BlockSets; Long GaugeBlock & Mic Check Set.
128 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(Analog/Dial/Digital)L.C.: 10 µm
>600 mm to 1000 mm 14.0µm Using Gauges BlockSets; Long GaugeBlock & Mic Check Set.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 24 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 26
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
129 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(Analog/Dial/Digital)L.C.: 10 µm
0 to 300 mm 6.9µm Using Gauges BlockSets; Long GaugeBlock & Mic Check Set.
130 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(Digital)L.C.: 0.1µm
0 to 25 mm 0.4µm Using Gauge BlockSet.
131 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Feeler Gauge Up to 2 mm 1.5µm Using DigimaticMicrometer.
132 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
FlankinessGauge/ElongationGauge/Receiver Gauge
0 to 100 mm 16.8 µm Using Profile Projector& Digital VernierCaliper
133 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Height Gauge(Vernier/Dial/Digital)L.C.: 10 µm
0 to 1000 mm 20µm Using Caliper Checker;Gauge Block & SurfacePlate.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 25 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 27
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
134 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Height Gauge(Vernier/Dial/Digital)L.C.: 10 µm
0 to 600 mm 11µm Using Caliper Checker;Gauge Block & SurfacePlate.
135 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Inside Micrometer /Caliper TypeL.C. : 1µm
5 mm to 50 mm 3.0µm Using Gauge Block Set& Gauge BlockAccessories.
136 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Inside Micrometer /Caliper TypeL.C. : 10µm
5 mm to 300 mm 5.0µm Using Gauge Block Set& Gauge BlockAccessories.
137 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Inside Micrometer /Stick Micrometer (2points)Basic Travel ofMicrometer (Plain)L.C.:10 µm
50 mm to 63 mm 4.2µm Using Gauge BlockSet; Long Gauge BlockSet & Mic Check Set &Electronic Probe withComparator.
138 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Inside Micrometer /Stick Micrometer (2points)Overall LengthAccuracy withExtension Rod(Stick)L.C.: 10 µm
50 mm to 1050 mm 12.0µm Using Gauge BlockSet; Long Gauge BlockSet & Mic Check Set &Electronic Probe withComparator.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 26 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 28
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
139 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Internal CaliperGaugeL.C.: 10 µm
2.5 mm to 250 mm 7.1µm Using Gauge Block Set& Gauge BlockAccessories.
140 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Lever Dial GaugeL.C. :1 µm
Up to 0.14 mm 1.6µm Using Dial CalibrationTester.
141 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Lever Dial GaugeL.C. :10 µm
Up to 1 mm 5.9µm Using Dial CalibrationTester.
142 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Lever Dial GaugeL.C. :2 µm
Up to 2 mm 1.9µm Using Dial CalibrationTester.
143 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Limit Gauge/CDGauge/PCD Gauge
0 to 200 mm 16.8 µm Using Profile Projector,LMM & 2Height Gaugeby Comparison Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 27 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 29
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
144 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Measuring Scale 0 to 2000 mm 120 X Sq rt(L) µm, L inmtr.
Using Scale & TapeCalibration Unit
145 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Measuring Tape 0 to 100000 mm 120 X Sq rt(L) µm, L inmtr.
Using Scale & TapeCalibration Unit.
146 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Measuring Tape (PiTape)
0 to 15000 mm 120 X Sq rt(L) µm, L inmtr.
Using Scale & TapeCalibration Unit.
147 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Micrometer Setting Rod 300 mm to 1000 mm 10.0µm Using Gauge BlockSet; Long Gauge BlockSet & ElectronicComparator withProbe.
148 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Micrometer Setting Rod Up to 300 mm 4.5µm Using Gauge BlockSet; Long Gauge BlockSet & ElectronicComparator withProbe.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 28 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 30
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
149 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Parallel Thread PlugGauge
2 mm to 100 mm 4.1µm Using FCDM,Cylindrical SettingMaster & ThreadMeasuring Wires.
150 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Pistol CaliperL.C.: 50µm
Up to 100 mm 26.1µm Using Gauge BlockSet.
151 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Plain Plug Gauge 1 mm mm to 100 mm 2.0µm Using Gauge Block Set& Electronic Probe.
152 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Plain Plug Gauge 100 mm to 160 mm 5.0µm Using Gauge Block Set& Electronic Probe.
153 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Plain Ring Gauge 3 mm to 100 mm 2.0µm Using ULM & MasterRing.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 29 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 31
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
154 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Plunger DialGaugeL.C. : 1 µm
0 mm to 25 mm 1.7µm Using Dial CalibrationTester & Gauge BlockSet.
155 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Plunger DialGaugeL.C. : 1 µm
0 mm to 50 mm 2.2µm Using Dial CalibrationTester & Gauge BlockSet.
156 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Radius Gauge/RadiusTemplete
Up to 40 mm 15.2µm Using Profile Projector.
157 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Screw / Thread PitchGauge - Angle
55° & 60° 9.5Min of Arc Using Profile Projector
158 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Screw / Thread PitchGauge - Pitch
Up to 7 mm 12µm Using Profile Projector
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 30 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 32
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
159 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Sine Bar Up to 300 mm 9arc sec Using Gauge Block;Angle Gauge Block;Elec. Probe & SurfacePlate.
160 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Snap Gauge >100 mm to 200 mm 6.0µm Using Gauge BlockSet.
161 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Snap Gauge 1 mm to 100 mm 3.0µm Using Gauge Block Set
162 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Spirit / PrecisionLevelL.C.: 20 µm/m
Up to 300 mm 14.4µm/m Using Electronic Level.
163 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Surface Plate 1000 mm X 1000 mm 1.2 xv(L+W)/125 L&Win mm
Using Electronic Level,L.C.1µm/m.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 31 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 33
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
164 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Taper Scale 0.1 mm to 16 mm 13.6µm Using Profile Projector.
165 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Taper Thread PlugGauge
2 mm to 100 mm 4.1µm Using FCDM,Cylindrical SettingMaster & ThreadMeasuring Wires.
166 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Templates/Plain WorkPiece/Inspection JigandFixture/Moulds/LeverArm/ MasterConnecting Rod
0 to 600 mm, 0 to 360° 16.8 µm, 3.6 min Using Gauge Block set,2D Height Gauge,Profile Projector, LLM,Electronic Comparator,Digital Vernier Caliper,Digital Micrometer,Bevel Protractor, AngleGauge Set, Sine Bar,Gauge Block set andElectronic Comparatorby Comparison Method
167 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Test Sieves Up to 125 mm 13µm Using Profile Projector& Digital VernierCaliper
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 32 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 34
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
168 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thickness Foils 0.01 mm to 12 mm 1.12µm Using Electronic Probe.
169 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread MeasuringWires
0.17 mm to 6.35 mm 1.3µm Using Electronic Probe.
170 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread Ring Gauge 3 mm to 100 mm 2.0µm Using ULM & MasterRing.
171 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Ultrasonic ThicknessGauge.L.C.: 0.01 mm
0 to 200 mm 72µm Using Steel MasterRod.
172 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Vickers/Knoop/Rockwell Diamond ConeIndenter
0 to 100 mm, 0 to 360° 16.8 µm, 3.6 min Using Profile Projector
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 33 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 35
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
173 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Weld Fillet Gauge Up to 100 mm 16.8 µm Using Profile Projectorby Comparison method
174 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Weld/Hi-Lo Gauge,Bridge Cam Gauge
0 to 60 mm, 0 to 60° 16.8 µm, 3.6 min Using Profile Projector,Gauge Block Set, Tapeand Scale calibrator byComparison method
175 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Width Gauge / HeightSetting Master
>100 mm to 160 mm 5.0µm Using Gauge Block Set& Electronic Probe.
176 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Width Gauge / HeightSetting Master
0 mm to 100 mm 2.0µm Using Gauge Block Set& Electronic Probe.
177 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Width Gauge/PaddleGauge
0 to 200 mm 16.8 µm Using Profile ProfileProjector, Gauge BlockSet, & Electronic Probe
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 34 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 36
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
178 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Wire Gauge 0.025 mm to 8 mm 12µm Using Profile Projector.
179 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Electronic LevelL.C.: 1µm/m
Up to 150 mm 7.2µm/m Using Electronic Level.
180 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Gauge Block - Carbide >25 mm to 50 mm 0.10µm Using Gauge Block Gr.’K” & Gauge BlockCalibrator.
181 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Gauge Block - Carbide >50 mm to 75 mm 0.13µm Using Gauge Block Gr.’K” & Gauge BlockCalibrator.
182 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Gauge Block - Carbide >75 mm to 100 mm 0.15µm Using Gauge Block Gr.’K” & Gauge BlockCalibrator.
183 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Gauge Block - Carbide 0.5 mm to 25 mm 0.09µm Using Gauge Block Gr.’K” & Gauge BlockCalibrator.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 35 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 37
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
184 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Gauge Block - Steel >25 mm to 50 mm 0.15µm Using Gauge Block Gr.’K” & Gauge BlockCalibrator.
185 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Gauge Block - Steel >50 mm to 75 mm 0.18µm Using Gauge Block Gr.’K” & Gauge BlockCalibrator.
186 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Gauge Block - Steel >75 mm to 100 mm 0.22µm Using Gauge Block Gr.’K” & Gauge BlockCalibrator.
187 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Gauge Block - Steel 0.5 mm to 25 mm 0.12µm Using Gauge Block Gr.’K” & Gauge BlockCalibrator.
188 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Length MeasuringMachine.L.C.:0.0001mm
0 to 100 mm 0.66µm Using Slip Gauge SetGrade 'k' byComparison Method.
189 MECHANICAL-DUROMETER
Rubber HardnessTester
0 to 100 Shore A 0.5Shore A Rubber hardnessCalibration (MicrometerHead with Fixture) ByDepth IndentationMethod as per ISO18898
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 36 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 38
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
190 MECHANICAL-DUROMETER
Rubber HardnessTester
0 to 100 Shore D 0.5Shore D Rubber hardnessCalibration (MicrometerHead with Fixture) ByDepth IndentationMethod as per ISO18898
191 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic Pressure -Dial/Digital PressureIndicating Device;PressureTransmitter/Switches.
0 bar to 1000 bar 0.12bar Using Digital PressureCalibrator & HydraulicComparator as perDKD- R - 6 -1
192 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic Pressure -Dial/Digital PressureIndicating Device;PressureTransmitter/Switches.
0 bar to 250 bar 0.05bar Using Digital PressureCalibrator & HydraulicComparator as perDKD- R - 6 -1
193 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic Pressure -Dial/Digital PressureIndicating Device;PressureTransmitter/Switches.
0 bar to 700 bar 0.12bar Using Digital PressureCalibrator & HydraulicComparator as perDKD- R - 6 -1
194 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic Pressure -Dial/Digital PressureIndicating Device;PressureTransmitter/Switches.
0 bar to 20 bar 5.6mbar Using Digital PressureCalibrator & HydraulicComparator as perDKD- R - 6 -1
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 37 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 39
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
195 MECHANICAL-PRESSUREINDICATING DEVICES
Negative Pressure -Dial / Digital VacuumGauge, PressureIndicating Devices.
0 mbar to -200 mbar 0.25mbar Using Digital PressureCalibrator with Vacuum/ Pneumatic HandPressure Pump byComparison MethodDKD- R - 6 -1
196 MECHANICAL-PRESSUREINDICATING DEVICES
Negative Pressure -Dial / Digital VacuumGauge, PressureIndicating Devices,PressureTransmitter/Switches.
0 bar to -0.95 bar 1.3mbar Using Digital PressureCalibrator with Vacuum/ Pneumatic HandPressure Pump byComparison MethodDKD- R - 6 -1
197 MECHANICAL-PRESSUREINDICATING DEVICES
Pneumatic Pressure -Dial / Digital PressureGauge, PressureIndicating Devices &PressureTransmitter/Switches
0 bar to 20 bar 5.6mbar Using Digital PressureCalibrator with Vacuum/ Pneumatic HandPressure Pump byComparison Method asper DKD- R - 6 -1
198 MECHANICAL-PRESSUREINDICATING DEVICES
Pneumatic Pressure -Dial / Digital PressurePressure IndicatingDevice & PressureTransmitter/Switches
0 bar to 2 bar 1mbar Using Digital PressureCalibrator with Vacuum/ Pneumatic HandPressure Pump byComparison Method asper DKD- R - 6 -1
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 38 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 40
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
199 MECHANICAL-PRESSUREINDICATING DEVICES
Pneumatic Pressure -Dial/Digital LowPressure IndicatingDevices & PressureTransmitter.
0 mbar to 200 mbar 0.25mbar Using DigitalManometer withVacuum / PneumaticHand Pressure Pumpby Comparison Methodas per DKD- R - 6 -1
200 MECHANICAL-PRESSUREINDICATING DEVICES
Pneumatic Pressure -Pressure IndicatingDevices(MaghnelicGauges, Low PressureGauges, Calibrators)
0 Pa to 500 Pa 0.35 Pa Using Digital PressureCalibrator byComparison MethodDKD- R - 6 -1
201 MECHANICAL-TORQUEMEASURINGDEVICES
Torque Screw Driver/Torque Wrench /Torque DialGaugesType I & II (AllClass)(Clock wise andanti-clock wise)
0.1 Nm to 10 Nm 1.3% Using ElectronicTorque WrenchCalibrator as per ISO6789:2003 / 2017
202 MECHANICAL-TORQUEMEASURINGDEVICES
Torque Screw Driver/Torque Wrench /Torque DialGaugesType I & II (AllClass)(Clock wise andanti-clock wise)
10 Nm to 200 Nm 1.3% Using ElectronicTorque WrenchCalibrator as per ISO6789:2003 / 2017
203 MECHANICAL-TORQUEMEASURINGDEVICES
Torque Screw Driver/Torque Wrench /Torque DialGaugesType I & II (AllClass)(Clock wise andanti-clock wise)
200 Nm to 1000 Nm 1.3% Using ElectronicTorque WrenchCalibrator as per ISO6789:2003 / 2017
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 39 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 41
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
204 MECHANICAL-VOLUME
Glass Pipettes &Burette
>10 ml to 100 ml 5µl Using Weighingbalance of Readability(0.01 / 0.1) mg &Distilled water byGravimetric methodbased on ISO 4787
205 MECHANICAL-VOLUME
Glass Pipettes &Burette
0.1 ml to 10 ml 2.4µl Using Weighingbalance of Readability(0.01 / 0.1) mg &Distilled water byGravimetric methodbased on ISO 4787
206 MECHANICAL-VOLUME
Glassware & Plasticwares (Such asMeasuring Cylinder /Volumetric Flask / Jar /Can etc.)
>10 ml to 100 ml 19.5µl Using Weighingbalance of Readability(0.01 / 0.1) mg &Distilled water byGravimetric methodbased on ISO 4787
207 MECHANICAL-VOLUME
Glassware & Plasticwares (Such asMeasuring Cylinder /Volumetric Flask / Jar /Can etc.)
>100 ml to 500 ml 21.3µl Using Weighingbalance of d:1 mg &Distilled water byGravimetric methodbased on ISO 4787
208 MECHANICAL-VOLUME
Glassware & Plasticwares (Such asMeasuring Cylinder /Volumetric Flask / Jar /Can etc.)
>2 L to 5 L 316.4µl Using Weighingbalance of d:10 mg &Distilled water byGravimetric methodbased on ISO 4787
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 40 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 42
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
209 MECHANICAL-VOLUME
Glassware & Plasticwares (Such asMeasuring Cylinder /Volumetric Flask / Jar /Can etc.)
>500 ml to 2 L 19.5µl to 249ul Using Weighingbalance of d:10 mg &Distilled water byGravimetric methodbased on ISO 4787
210 MECHANICAL-VOLUME
Glassware & Plasticwares (Such asMeasuring Cylinder /Volumetric Flask / Jar /Can etc.)
0.1 ml to 10 ml 2.9µl Using Weighingbalance of Readability(0.01 / 0.1) mg &Distilled water byGravimetric methodbased on ISO 4787
211 MECHANICAL-VOLUME
Micro pipettes (PistonOperated-Apparatus)
1 ml to 5 ml 4µl Using Weighingbalance of Readability(0.01 / 0.1) mg &Distilled water byGravimetric methodbased on ISO 8655-6
212 MECHANICAL-VOLUME
Micro pipettes(PistonOperated-Apparatus)
100 µl to 1000 µl 0.35µl Using Weighingbalance of Readability(0.01 / 0.1) mg &Distilled water byGravimetric methodbased on ISO 8655-6
213 MECHANICAL-VOLUME
Micro pipettes(PistonOperated-Apparatus)
10 µl to 100 µl 0.30µl Using Weighingbalance of Readability(0.01 / 0.1) mg &Distilled water byGravimetric methodbased on ISO 8655-6
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 41 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 43
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
214 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing Balance(d =0.01 g)
0 kg to 5 kg 0.1g Using Weights ofaccuracy class E2 & F1as per OIML R-76
215 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing Balance(d =0.01 mg)
0 g to 100 g 0.03mg Using Weights ofaccuracy class E2 asper OIML R-76
216 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing Balance(d =0.1 g)
0 kg to 30 kg 0.1g Using Weights ofaccuracy class E2 & F1as per OIML R-76
217 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing Balance(d =0.1 mg)
0 g to 200 g 0.10mg Using Weights ofaccuracy class E2 asper OIML R-76
218 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing Balance(d =1 mg)
0 kg to 1 kg 1.0mg Using Weights ofaccuracy class E2 asper OIML R-76
219 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F2 Class &Coarser
2 kg 8.6mg Using E2 class weightsand balance of d: 0.01g as per OIML R-111.Based on ABBAMethod
220 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F2 Class &Coarser
5 kg 9mg Using E2 class weightsand balance of d: 0.01g as per OIML R-111.Based on ABBAMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 42 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 44
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
221 MECHANICAL-WEIGHTS
Weights (ConventionalMass)M1 Class &Coarser
10 kg 80mg Using E2 & F1 classweights and balance ofd: 0.1 g as per OIML R-111. Based on ABBAMethod
222 MECHANICAL-WEIGHTS
Weights (ConventionalMass)M1 Class &Coarser
20 kg 100mg Using E2 & F1 classweights and balance ofd: 0.1 g as per OIML R-111. Based on ABBAMethod
223 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
1 g 0.02mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod.
224 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
1 kg 1.2mg Using E2 class weightsand balance of d: 0.001g as per OIML R-111.Based on ABBAMethod
225 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
10 g 0.02mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 43 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 45
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
226 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
10 mg 0.011mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod
227 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
100 g 0.08mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod.
228 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
100 mg 0.02mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod
229 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
2 g 0.02mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 44 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 46
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
230 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
2 mg 0.011mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod
231 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
20 g 0.05mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod.
232 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
20 mg 0.01mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod
233 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
200 g 0.15mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 45 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 47
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
234 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
5 g 0.02mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod.
235 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
5 mg 0.011mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod
236 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
50 g 0.05mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod.
237 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
50 mg 0.01mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod
238 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
500 g 1.0mg Using E2 class weightsand balance of d: 0.001g as per OIML R-111.Based on ABBAMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 46 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 48
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
239 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
500 mg 0.02mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod.
240 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F2 Class &Coarser
200 mg 0.02mg Using E2 classstandard weights andBalance of d: 0.01 mg /0.1 mg as per OIML R-111. Based on ABBAMethod.
241 MECHANICAL-WEIGHTS
Weights (ConventionalMass)F1 Class &Coarser
1 mg 0.011mg Using E2 classstandard weights andBalance of d: 0.01 mgas per OIML R-111.Based on ABBAMethod.
242 THERMAL-MISCELLANEOUS
Temperature Gauge 30°C to 250°C0.30°C Using PRT with
6.5DMM orMUltifunction Calibratorand Liquid bath bycomparison method
243 THERMAL-TEMPERATURE
Glass Thermometers -80 °C to 250 °C 0.24°C Using SPRT with 6.5DMM or Multifunctioncalibrator and Liquidbath by ComparisonMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 47 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 49
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
244 THERMAL-TEMPERATURE
Infrared/Non-contactType Thermometer
>300 °C to 650 °C 6.1°C Using RTD/N type/IRPyrometer Sensor withMultifunction calibratorAnd Black body sourceby Comparison Method
245 THERMAL-TEMPERATURE
Infrared/Non-contactType Thermometer
50 °C to 300 °C 5.2°C Using RTD/N type/IRPyrometer Sensor withMultifunction calibratorAnd Black body sourceby Comparison Method
246 THERMAL-TEMPERATURE
Temperature Gauge 0 °C to 600 °C 0.24°C Using SPRT with 6.5DMM or Multifunctioncalibrator and Liquidbath by ComparisonMethod
247 THERMAL-TEMPERATURE
Temperature Indicator/Controller with Sensorof Dry Well Block &Furnace.
>1000 °C to 1200 °C 2.44°C Using R- TypeThermocouple withMultifunction calibratorand Liquid bath /Dryblock by ComparisonMethod Single PositionCalibration
248 THERMAL-TEMPERATURE
Temperature Indicator/Controller with Sensorof Dry Well Block &Furnace.
>400 °C to 650 °C 0.16°C Using SPRT with 6.5DMM or Multifunctioncalibrator and Liquidbath /Dry block byComparison MethodSingle PositionCalibration
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 48 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 50
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
249 THERMAL-TEMPERATURE
Temperature Indicator/Controller with Sensorof Dry Well Block &Furnace.
>650 °C to 1000 °C 2.32°C Using R- TypeThermocouple withMultifunction calibratorand Liquid bath /Dryblock by ComparisonMethod Single PositionCalibration
250 THERMAL-TEMPERATURE
Temperature Indicator/Controller with Sensorof Dry Well Block/Liquid Bath / Incubators/ Oven / Furnace
>250 °C to 400 °C 0.21°C Using SPRT with 6.5DMM or Multifunctioncalibrator and Liquidbath /Dry block byComparison MethodSingle PositionCalibration
251 THERMAL-TEMPERATURE
Temperature Indicator/Controller with Sensorof Dry Well Block/Liquid Bath / Incubators/ Oven / Furnace
>50 °C to 250 °C 0.19°C Using SPRT with 6.5DMM or Multifunctioncalibrator and Liquidbath /Dry block byComparison MethodSingle PositionCalibration
252 THERMAL-TEMPERATURE
Temperature Indicator/Controller with Sensorof Dry Well Block/Liquid Bath / Incubators/ Oven / Furnace
-80 °C to 50 °C 0.22°C Using SPRT with 6.5DMM or Multifunctioncalibrator and Liquidbath /Dry block byComparison MethodSingle PositionCalibration
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 49 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 51
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
253 THERMAL-TEMPERATURE
Temperature sensor(RTD/ Thermocouple)With & withoutindicator, &Temperaturetransmitter
>1000 °C to 1200 °C 2.43°C Using R- TypeThermocouple withMultifunction calibrator& dry blockTemperature baths byComparison Method
254 THERMAL-TEMPERATURE
Temperature sensor(RTD/ Thermocouple)With & withoutindicator, &Temperaturetransmitter
>250 °C to 400 °C 0.21°C Using SPRT with6.5DMM orMultifunction calibratorwith Liquid/ Dry blockbath By ComparisonMethod
255 THERMAL-TEMPERATURE
Temperature sensor(RTD/ Thermocouple)With & withoutindicator, &Temperaturetransmitter
>400 °C to 650 °C 0.21°C Using SPRT with6.5DMM orMultifunction calibratorwith Liquid/ Dry blockbath By ComparisonMethod
256 THERMAL-TEMPERATURE
Temperature sensor(RTD/ Thermocouple)With & withoutindicator, &Temperaturetransmitter
>50 °C to 250 °C 0.19°C Using SPRT with6.5DMM orMultifunction calibratorwith Liquid/ Dry blockbath By ComparisonMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 50 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 52
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
257 THERMAL-TEMPERATURE
Temperature sensor(RTD/ Thermocouple)With & withoutindicator, &Temperaturetransmitter
>650 °C to 1000 °C 2.32°C Using R- TypeThermocouple withMultifunction calibrator& dry blockTemperature baths byComparison Method
258 THERMAL-TEMPERATURE
Temperature sensor(RTD/ Thermocouple)With & withoutindicator, &Temperaturetransmitter
-80 °C to 50 °C 0.22°C Using SPRT with6.5DMM orMultifunction calibratorwith Liquid/ Dry blockbath By ComparisonMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 51 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 53
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
Site Facility
1 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current 1 kHz 100 µA to 200 µA 0.26% to 0.39% Using 6 ½ DigitMultimeter 8846A byDirect Method
2 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current 50 Hz 10 A to 3200 A 0.4% Using Standard CurrentTransformer with 6 ½Digit Multimeter 8846Aby Direct Method
3 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current 50 Hz to 1kHz
0.2 mA to 100 mA 0.39% to 0.18% Using 6 ½ DigitMultimeter 8846A byDirect Method
4 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Measure)
AC Current 50 Hz to 1kHz
100 mA to 10 A 0.18% to 0.29% Using 6 ½ DigitMultimeter 8846A byDirect Method
5 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Current 1 kHz to 5kHz
3 mA to 3 A 0.16% to 3.54% Using Multi ProductCalibrator 5502A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 52 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 54
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
6 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Current 50 Hz 20 A to 1000 A 0.79% Using MPF 5502 A withCurrent Coil by DirectMethod
7 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Current 50 Hz to 1kHz
10 A to 20 A 0.17% to 0.36% Using Multi ProductCalibrator 5502A byDirect Method
8 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Current 50 Hz to 1kHz
3 A to 10 A 0.16% to 0.17% Using Multi ProductCalibrator 5502A byDirect Method
9 ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1 GHZ)(Source)
AC Current 50 Hz to 1KHz
30 uA to 3 mA 1.44% to 0.16% Using Multi ProductCalibrator 5502A byDirect Method
10 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 10 uA to 100 mA 0.36% to 0.064% Using 6 ½ DigitMultimeter 8846A byDirect Method
11 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 100 mA to 3 A 0.064% to 0.19% Using 6 ½ DigitMultimeter 8846A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 53 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 55
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
12 ELECTRO-TECHNICAL- DIRECTCURRENT (Measure)
DC Current 3 A to 10 A 0.19% Using 6 ½ DigitMultimeter 8846A byDirect Method
13 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Current 10 µA to 100 µA 0.26% to 0.044% Using Multi ProductCalibrator 5502A byDirect Method
14 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Current 100 uA to 3 mA 0.044% to 0.031% Using Multi ProductCalibrator 5502A byDirect Method
15 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Current 20 A to 1000 A 0.64% Using MPF 5502 AWith Current Coil byDirect Method
16 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Current 3 A to 20 A 0.11% to 0.38% Using Multi ProductCalibrator 5502A byDirect Method
17 ELECTRO-TECHNICAL- DIRECTCURRENT (Source)
DC Current 3 mA to 3 A 0.031% to 0.11% Using Multi ProductCalibrator 5502A byDirect Method
18 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
CurrentTransformer(PhaseError)5A (Secondary)1% to 120% of ratedcurrent
1 A to 3200 A 3.34min Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
19 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
CurrentTransformer(RatioError)5A (Secondary)1% to 120% of ratedcurrent
1 A to 3200 A 0.047% Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 54 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 56
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
20 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
AC HIGH VOLTAGE 1 kV to 40 kV 3.2% Using HV Divider withKV Meter
21 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
AC High Voltage 50 Hz 1 kV to 5 kV 3.2% to 3.8% Using Udeyraj makeHV Divider withindicator by DirectMethod
22 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
AC High Voltage 50 Hz 5 kV to 100 kV 3.8% to 3.2% Using Udeyraj makeHV Divider withindicator by DirectMethod
23 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
AC Voltage 1 kHz 1 mV to 20 mV 4.72% to 0.33% Using 6 ½ DigitMultimeter 8846A byDirect Method
24 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
AC Voltage 50 Hz to 1kHz
20 mV to 1000 V 0.54% to 0.10% Using 6 ½ DigitMultimeter 8846A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 55 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 57
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
25 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Phase Error)1A(Secondary)From 1%to 120% of ratedcurrent
1 A to 3200 A 3.36min Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
26 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Phase Error)1A/5ASecondary from 1% to120% of rated current
2000 A to 7500 A 3.4min Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
27 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Phase Error)5A (Secondary)From 5% to120% of rated current
3000 A to 6000 A 3.36min Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
28 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Phase Error)5A(Secondary)From 1%to 5% of rated current
3000 A to 6000 A 3.36min Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
29 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Ratio Error)1A(Secondary)From 1%to 120% of ratedcurrent
1 A to 3200 A 0.05% Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 56 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 58
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
30 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Ratio Error)1A/5ASecondary from 1% to120% of Rated Current
2000 A to 7500 A 0.085% Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
31 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Ratio Error)5A (Secondary)From 5% to120% of rated current
3000 A to 6000 A 0.1% Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
32 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Current Transformer(Ratio Error)5A(Secondary)From 1%to 5% of rated current
3000 A to 6000 A 0.1% Using Standard Currenttransformer &Instrument transformertest set up ByComparison Method
33 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC High Voltage 1 kV to 5 kV 3.2% Using Udeyraj makeHV Divider withindicator by DirectMethod
34 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC High Voltage 5 kV to 40 kV 3.2% Using Udeyraj makeHV Divider withindicator by DirectMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 57 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 59
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
35 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC Resistance 1 mOhm to 1 Ohm 0.42% to 0.36% Using 6 ½ DigitMultimeter 8846A byV/I Method
36 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC Resistance 1 MOhm to 1000MOhm
0.013% to 2.31% Using 6 ½ DigitMultimeter 8846A byDirect Method
37 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC Resistance 1 Ohm to 1 MOhm 0.36% to 0.013% Using 6 ½ DigitMultimeter 8846A byDirect Method andVoltage/ CurrentMethod
38 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC Voltage 1 mV to 100 mV 0.42% to 0.085% Using 6 ½ DigitMultimeter 8846A byDirect Method
39 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
DC Voltage 100 mV to 1000 V 0.085% to 0.007% Using 6 ½ DigitMultimeter 8846A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 58 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 60
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
40 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Potential Transformer(Phase Error)
11000/110 4.03min Using StandardPotential transformer &Instrument transformertest set up ByComparison Method
41 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Potential Transformer(Phase Error)
11000/63.5 3.16min Using StandardPotential transformer &Instrument transformertest set up ByComparison Method
42 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Potential Transformer(Ratio Error)
11000/110 0.16% Using StandardPotential transformer &Instrument transformertest set up ByComparison Method
43 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Potential Transformer(Ratio Error)
11000/63.5 0.16% Using StandardPotential transformer &Instrument transformertest set up ByComparison Method
44 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT(Measure)
Voltage Ratio 0.8 to 2021 ratio 0.16% Using 6 ½ DigitMultimeter 8846A andFluke 5502A by DirectMethod
45 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Power 50 [email protected] UPF 120/2240 V 0.1A to 20 A
1.2 W to 4800 W 3.47% to 0.23% Using Multi ProductCalibrator 5502A withPower Option by DirectMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 59 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 61
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
46 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Vertical deflectionHorizontal Deflection 1kHz
5m V to 50 V 2.64% to 0.40% Using Multi ProductCalibrator 5502A withScope Option by DirectMethod
47 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Voltage 1 kHz 2 mV to 10 mV 1.76% to 0.41% Using Multi ProductCalibrator 5502A byDirect Method
48 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Voltage 1 kHz to 10kHz
30 V to 1000 V 0.1% Using Multi ProductCalibrator 5502A byDirect Method
49 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Voltage 50 Hz to 1kHz
10 mV to 300 mV 0.41% to 0.044% Using Multi ProductCalibrator 5502A byDirect Method
50 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Voltage 50 Hz to 1kHz
300 mV to 300 V 0.044% to 0.1% Using Multi ProductCalibrator 5502A byDirect Method
51 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
AC Voltage 50 Hz to 1kHz
300 V to 1000 V 0.1% Using Multi ProductCalibrator 5502A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 60 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 62
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
52 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Capacitance @ 1 kHz 10 pF to 1 nF 2.98% to 1.2% Using DecadeCapacitance Box &Multi Product Calibrator5502A by DirectMethod
53 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Capacitance @1 kHz 9 nF to 1 mF 1.26% to 0.80% Using DecadeCapacitance Box &Multi Product Calibrator5502A by DirectMethod
54 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Capacitance @1kHz 1 nF to 9 nF 1.7% to 1.26% Using DecadeCapacitance Box &Multi Product Calibrator5502A by DirectMethod
55 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Power @ 1 V to600 V, 1A to 20 A
1 W to 12 KW 0.37% to 0.25% Using MultiproductCalibrator 5502A withPower Option by DirectMethod.
56 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Resistance 1 mohm to 1 mohm 0.6% to 0.6% Using Shunt By DirectMethod
57 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Resistance 1 Ohm to 100 Ohm 0.25% to 0.072% Using Multi ProductCalibrator 5502A byDirect Method.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 61 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 63
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
58 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Resistance 100 kOhm to 100MOhm
0.021% to 0.58% Using Multi ProductCalibrator 5502A byDirect Method
59 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Resistance 100 ohm to 100 kOhm 0.072% to 0.021% Using Multi ProductCalibrator 5502A byDirect Method
60 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Voltage 1 mV to 100 mV 0.36% to 0.013% Using Multi ProductCalibrator 5502A byDirect Method.
61 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Voltage 100 mV to 30 V 0.013% to 0.0064% Using Multi ProductCalibrator 5502A byDirect Method.
62 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
DC Voltage 30 V to 1000 V 0.0064% to 0.007% Using Multi ProductCalibrator 5502A byDirect Method.
63 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
High Resistance 100 kohm to 1 Tohm 1.2% to 2.4% Using DecadeResistance Box byDirect Method
64 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Inductance @1 kHz 1 mH to 10 H 1.53% to 2.03% Using DecadeInductance Box byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 62 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 64
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
65 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
ODD Harmonics(Current) upto 41st
100 mA to 6 A 0.75% Using FlukeMultiProduct Calibrator5502A
66 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
ODD Harmonics upto41st Voltage
100 mV to 60 V 0.75% Using FlukeMultiproduct Calibrator5502A
67 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Oscilloscope DCFunction
2 mV to 33 V 6.59% to 0.33% Using Multi ProductCalibrator 5502A withScope Option by DirectMethod
68 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Power Factor 50 Hz 0.1 to UPF 0.05PF Using Multi ProductCalibrator 5502A withPower Option by DirectMethod
69 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Voltage ratio 0.8 to 400 0.5% to 0.3% Using TransformerRatio Standard byComparison Method
70 ELECTRO-TECHNICAL-ELECTRICALEQUIPMENT (Source)
Voltage Ratio 400 to 2021 0.5% to 0.3% Using TransformerRatio Standard byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 63 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 65
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
71 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -RTD(Calibration oftemperature Indicator /Controller/ Recorder/Calibrator)
(-)200 °C to 800 °C 0.51°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
72 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)C-Type
0 °C to 2315 °C 1.4°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
73 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)E-Type
(-)270 °C to 1300 °C 0.37°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
74 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)J-Type
(-)200 °C to 1200 °C 0.35°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 64 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 66
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
75 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)K-Type
(-)250 °C to 1137 °C 0.47°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
76 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)L-Type
(-)200 °C to 600 °C 0.37°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
77 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)N-Type
(-)270 °C to 1300 °C 0.47°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
78 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)R-Type
(-)50 °C to 1767 °C 0.9°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 65 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 67
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
79 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)S-Type
(-)50 °C to 1767 °C 0.8°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
80 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)T-Type
(-)270 °C to 400 °C 0.35°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
81 ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator /Controller/Recorder/Calibrator)U-Type
(-)200 °C to 600 °C 0.5°C Using MultifunctionCalibrator(BeamextoMC2) byDirect Method
82 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -RTD(Calibration oftemperature Indicator /Controller/ Recorder/Calibrator)
(-) 200 °C to 800 °C 0.27°C Using Multi ProductCalibrator 5502A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 66 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 68
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
83 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)EType
(-)200 °C to 1000 °C 0.55°C Using Multi ProductCalibrator 5502A byDirect Method
84 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)JType
(-)210 °C to 1200 °C 0.37°C Using Multi ProductCalibrator 5502A byDirect Method
85 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)KType
(-)200 °C to 1372 °C 0.51°C Using Multi ProductCalibrator 5502A byDirect Method
86 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)NType
(-)200 °C to 1300 °C 0.61°C Using Multi ProductCalibrator 5502A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 67 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 69
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
87 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)RType
0 °C to 1700 °C 0.51°C Using Multi ProductCalibrator 5502A byDirect Method
88 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)SType
0 °C to 1700 °C 0.58°C Using Multi ProductCalibrator 5502A byDirect Method
89 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)TType
(-)200 °C to 400 °C 0.70°C Using Multi ProductCalibrator 5502A byDirect Method
90 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)UType
(-)200 °C to 600 °C 0.65°C Using Multi ProductCalibrator 5502A byDirect Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 68 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 70
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
91 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)BType
600 °C to 1820 °C 0.55°C Using Multi ProductCalibrator 5502A byDirect Method
92 ELECTRO-TECHNICAL-TEMPERATURESIMULATION (Source)
TemperatureSimulation -Thermocouple(Calibration of temperatureIndicator / Controller/Recorder/ Calibrator)CType
200 °C to 2315 °C 0.95°C Using Multi ProductCalibrator 5502A byDirect Method
93 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Frequency 10 Hz to 1 MHz 0.084% to 0.014% Using 6 ½ DigitMultimeter 8846A byDirect Method
94 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Time 0.1 sec to 1 hr 0.013sec to 2.32sec Using Digital TimeInterval Meter By DirectMethod
95 ELECTRO-TECHNICAL- TIME &FREQUENCY(Measure)
Time 1 hr to 24 hr 2.32sec to 5.18sec Using Digital TimeInterval Meter Bycomparison Method
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 69 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 71
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
96 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Bandwidth 50 MHz to 250 MHz 6.21% Using Multi ProductCalibrator 5502A withScope Option by DirectMethod
97 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Frequency 10 Hz to 300 kHz 0.086% to 0.0094% Using Multi ProductCalibrator 5502A byDirect Method
98 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Frequency 300 kHz to 2 MHz 0.0094% to 0.49% Using Multi ProductCalibrator 5502A byDirect Method
99 ELECTRO-TECHNICAL- TIME &FREQUENCY (Source)
Time Base 2 n Sec to 5 Sec 0.3% to 0.67% Using Multi ProductCalibrator 5502A withScope Option by DirectMethod
100 MECHANICAL-ACCELERATION ANDSPEED
Speed RPM - (Non-Contact)
10 RPM to 5000 RPM 2.1RPM Using Tachometer.
101 MECHANICAL-ACCELERATION ANDSPEED
Speed RPM - (Non-Contact)
5000 RPM to 30000RPM
19RPM Using Tachometer.
102 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Caliper(Vernier/Dial/Digital)L.C.:10 µm
1000 mm to 2000 mm 22.5µm Using Caliper Checker;Gauge Block; LengthBar & ExternalMicrometer.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 70 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 72
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
103 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial CalibrationTesterL.C.: 0.1 µm
0 to 25 mm 1.12µm Using Electronic Probe
104 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Electronic HeightGaugeL.C.: 0.5 µm
0 to 600 mm 8µm Using Gauge Block;Long Gauge & SurfacePlate.
105 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Height Gauge(Vernier/Dial/Digital)L.C.: 10 µm
0 to 1000 mm 20µm Using Caliper Checker;Gauge Block & SurfacePlate.
106 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Height Gauge(Vernier/Dial/Digital)L.C.: 10 µm
0 to 600 mm 11µm Using Caliper Checker;Gauge Block & SurfacePlate.
107 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
MetallurgicalMicroscope
100 x to 1000 x 0.3% Using Micro Scale ofL.C. 10 µm.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 71 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 73
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
108 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Straight Edge Upto 2000 mm 1.8 x v(L/125) µm L inmm
Using Electronic LevelL.C.1µm/m & GaugeBlock.
109 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Surface Plate 4000 mm X3000 mm 1.2 xv(L+W)/125 L&Win mm
Using Electronic Level,L.C.1 µm/m
110 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Length MeasuringMachine.L.C.:0.0001mm
0 to 100 mm 0.66µm Using Slip Gauge SetGrade 'k' byComparison Method.
111 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Profile Projector/VideoMeasuringMachineAngleL.C.:1sec
0 ° to 360 ° 6.0arc sec. Using AngularGraticule / AngleGauge Set.
112 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Profile Projector/VideoMeasuringMachineLinear : L.C.:0.1 µm
0 to 200 mm 4.8µm Using Glass Scale./Gauge Block.
113 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Profile Projector/VideoMeasuringMachineMagnification
Up to 100 X 1.2% Using Glass Scale &Digimatic Caliper.
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 72 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 74
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
114 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic Pressure -Dial/Digital PressureIndicating Device;PressureTransmitter/Switches.
0 bar to 1000 bar 0.12bar Using Digital PressureCalibrator & HydraulicComparator as perDKD- R - 6 -1
115 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic Pressure -Dial/Digital PressureIndicating Device;PressureTransmitter/Switches.
0 bar to 250 bar 0.05bar Using Digital PressureCalibrator & HydraulicComparator as perDKD- R - 6 -1
116 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic Pressure -Dial/Digital PressureIndicating Device;PressureTransmitter/Switches.
0 bar to 700 bar 0.12bar Using Digital PressureCalibrator & HydraulicComparator as perDKD- R - 6 -1
117 MECHANICAL-PRESSUREINDICATING DEVICES
Hydraulic Pressure -Dial/Digital PressureIndicating Device;PressureTransmitter/Switches.
0 bar to 20 bar 5.6mbar Using Digital PressureCalibrator & HydraulicComparator as perDKD- R - 6 -1
118 MECHANICAL-PRESSUREINDICATING DEVICES
Negative Pressure -Dial / Digital VacuumGauge, PressureIndicating Devices.
0 mbar to -200 mbar 0.25mbar Using Digital PressureCalibrator with Vacuum/ Pneumatic HandPressure Pump byComparison MethodDKD- R - 6 -1
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 73 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 75
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
119 MECHANICAL-PRESSUREINDICATING DEVICES
Negative Pressure -Dial / Digital VacuumGauge, PressureIndicating Devices,PressureTransmitter/Switches.
0 bar to -0.95 bar 1.3mbar Using Digital PressureCalibrator with Vacuum/ Pneumatic HandPressure Pump byComparison MethodDKD- R - 6 -1
120 MECHANICAL-PRESSUREINDICATING DEVICES
Pneumatic Pressure -Dial / Digital PressureGauge, PressureIndicating Devices &PressureTransmitter/Switches
0 bar to 20 bar 5.6mbar Using Digital PressureCalibrator with Vacuum/ Pneumatic HandPressure Pump byComparison Method asper DKD- R - 6 -1
121 MECHANICAL-PRESSUREINDICATING DEVICES
Pneumatic Pressure -Dial / Digital PressurePressure IndicatingDevice & PressureTransmitter/Switches
0 bar to 2 bar 1mbar Using Digital PressureCalibrator with Vacuum/ Pneumatic HandPressure Pump byComparison Method asper DKD- R - 6 -1
122 MECHANICAL-PRESSUREINDICATING DEVICES
Pneumatic Pressure -Dial/Digital LowPressure IndicatingDevices & PressureTransmitter.
0 mbar to 200 mbar 0.25mbar Using DigitalManometer withVacuum / PneumaticHand Pressure Pumpby Comparison Methodas per DKD- R - 6 -1
123 MECHANICAL-PRESSUREINDICATING DEVICES
Pneumatic Pressure -Pressure IndicatingDevices(MaghnelicGauges, Low PressureGauges, Calibrators)
0 Pa to 500 Pa 0.35 Pa Using Digital PressureCalibrator byComparison MethodDKD- R - 6 -1
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 74 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 76
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
124 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing Balance(d =0.01 g)
0 kg to 5 kg 0.1g Using Weights ofaccuracy class E2 & F1as per OIML R-76
125 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing Balance(d =0.01 mg)
0 g to 100 g 0.03mg Using Weights ofaccuracy class E2 asper OIML R-76
126 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing Balance(d =0.1 g)
0 kg to 30 kg 0.1g Using Weights ofaccuracy class E2 & F1as per OIML R-76
127 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing Balance(d =0.1 mg)
0 g to 200 g 0.10mg Using Weights ofaccuracy class E2 asper OIML R-76
128 MECHANICAL-WEIGHING SCALEAND BALANCE
Weighing Balance(d =1 mg)
0 kg to 1 kg 1.0mg Using Weights ofaccuracy class E2 asper OIML R-76
129 THERMAL-MISCELLANEOUS
Temperature Gauge 30°C to 250°C0.30°C Using PRT with
6.5DMM orMUltifunction Calibratorand Liquid bath bycomparison method
130 THERMAL- SPECIFICHEAT & HUMIDITY
Humidity chamber/climatic chamber/Environmentalchamber
10 °C to 60 °C 0.31°C Using Temperature &humidity Data loggerswireless by Multi PointCalibration
131 THERMAL- SPECIFICHEAT & HUMIDITY
Humidity chamber/climatic chamber/Environmentalchamber @25°C
15% RH to 95% RH 2.44%RHRH Using Temperature &humidity Data loggerswireless by Multi PointCalibration
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 75 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 77
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
132 THERMAL-TEMPERATURE
Deep Freezer,Refrigerators,Incubator, Oven,Temperature Bath,Chamber, Furnace
-80 °C to 300 °C 2.37°C UsingRTD/Thermocouple(K/J/N/ other type)sensor with MultiChannel Data Loggermulti Point Calibration
133 THERMAL-TEMPERATURE
Glass Thermometers 30 °C to 250 °C 0.25°C Using PRT with6.5DMM orMultifunction calibratorAnd Liquid bath byComparison Method
134 THERMAL-TEMPERATURE
Infrared /Non-contactType Thermometer
>300 °C to 650 °C 6.1°C Using RTD/N type/IRPyrometer Sensor withMultifunction calibratorand Black body sourceBy Comparison Method
135 THERMAL-TEMPERATURE
Infrared /Non-contactType Thermometer
50 °C to 300 °C 5.1°C Using RTD/N type/IRPyrometer Sensor withMultifunction calibratorand Black body sourceBy Comparison Method
136 THERMAL-TEMPERATURE
Temperature Bath,Chamber & Furnace.
300 °C to 1200 °C 2.95°C UsingRTD/Thermocouple(K/J/N/ other type)sensor with MultiChannel Data Loggermulti Point Calibration
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 76 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 78
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
137 THERMAL-TEMPERATURE
Temperature Indicator/Controller with Sensorof Dry Well Block &Furnace.
>400 °C to 650 °C 1.70°C Using R- TypeThermocouple withMultifunction calibratorand Liquid bath /Dryblock by ComparisonMethod Single PositionCalibration
138 THERMAL-TEMPERATURE
Temperature Indicator/Controller with Sensorof Dry Well Block &Furnace.
>650 °C to 1000 °C 2.32°C Using R- TypeThermocouple withMultifunction calibratorand Liquid bath /Dryblock by ComparisonMethod Single PositionCalibration
139 THERMAL-TEMPERATURE
Temperature Indicator/Controller with Sensorof Dry Well Block/Furnace.
>1000 °C to 1200 °C 2.44°C°C Using R- TypeThermocouple withMultifunction calibratorand Liquid bath /Dryblock by ComparisonMethod Single PositionCalibration
140 THERMAL-TEMPERATURE
Temperature Indicator/Controller with Sensorof Dry Well Block/Liquid Bath / Incubators/ Oven / Furnace
>50 °C to 250 °C 0.30°C Using PRT with6.5DMM orMultifunction calibratorAnd Liquid bath /Dryblock by ComparisonMethod Single PositionCalibration
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 77 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 79
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
141 THERMAL-TEMPERATURE
Temperature Indicator/Controller with Sensorof Dry Well Block/Liquid Bath /Incubators.
-80 °C to 50 °C 0.25°C°C Using PRT with6.5DMM orMultifunction calibratorAnd Liquid bath /Dryblock by ComparisonMethod Single PositionCalibration
142 THERMAL-TEMPERATURE
Temperature Indicator/Controller with Sensorof Dry Well Block/Liquid Bath / Oven /Furnace
>250 °C to 400 °C 0.65°C°C Using PRT with6.5DMM orMultifunction calibratorAnd Liquid bath /Dryblock by ComparisonMethod Single PositionCalibration
143 THERMAL-TEMPERATURE
Temperature sensor(RTD/Thermocouple)With & without indicator &Temperaturetransmitter
>1000 °C to 1200 °C 2.44°C Using R- TypeThermocouple withMultifunction calibrator& dry blockTemperature baths andDry bath byComparison Method
144 THERMAL-TEMPERATURE
Temperature sensor(RTD/Thermocouple)With & without indicator &Temperaturetransmitter
>250 °C to 400 °C 0.65°C Using SPRT/PRT with6.5DMM orMultifunction calibratorand Liquid/Dry blockbath By ComparisonMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 78 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -
Page 80
S.No Discipline / Group Measurand orReferenceMaterial/Type ofinstrument ormaterial to becalibrated ormeasured / QuantityMeasured /Instrument
Measurement rangeand additionalparameters whereapplicable(Rangeand Frequency)
Calibration andMeasurementCapability(CMC)(±)
Calibration orMeasurementMethod orprocedure)
145 THERMAL-TEMPERATURE
Temperature sensor(RTD/Thermocouple)With & without indicator &Temperaturetransmitter
>400 °C to 650 °C 1.70°C Using R- TypeThermocouple withMultifunction calibrator& dry blockTemperature baths andDry bath byComparison Method
146 THERMAL-TEMPERATURE
Temperature sensor(RTD/Thermocouple)With & without indicator &Temperaturetransmitter
>50 °C to 250 °C 0.30°C Using SPRT/PRT with6.5DMM orMultifunction calibratorand Liquid/Dry blockbath By ComparisonMethod
147 THERMAL-TEMPERATURE
Temperature sensor(RTD/Thermocouple)With & without indicator &Temperaturetransmitter
>650 °C to 1000 °C 2.32°C Using R- TypeThermocouple withMultifunction calibrator& dry blockTemperature baths andDry bath byComparison Method
148 THERMAL-TEMPERATURE
Temperature sensor(RTD/Thermocouple)With & without indicator &Temperaturetransmitter
-35 °C to 50 °C 0.25°C Using SPRT/PRT with6.5DMM orMultifunction calibratorand Liquid/Dry blockbath By ComparisonMethod
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, PLOT NO. 126,POR GIDC, POR, RAMANGAMDI, VADODARA, GUJARAT, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2205 Page No. : 79 / 79
Validity 17/01/2020 to 17/05/2021 Last Amended on -