A1-148 SRS Caged Ball LM Guide Miniature Type Model SRS Model SRS-WM Model SRS-M Wide type Compact type Side seal LM rail LM block Endplate End seal Ball Ball cage * For the ball cage, see A1-88. Point of Selection A1-10 Point of Design A1-450 Options A1-473 Model No. A1-537 Precautions on Use A1-543 Accessories for Lubrication A24-1 Mounting Procedure and Maintenance B1-89 Equivalent moment factor A1-43 Rated Loads in All Directions A1-58 Equivalent factor in each direction A1-60 Radial Clearance A1-70 Accuracy Standards A1-83 Shoulder Height of the Mounting Base and the Corner Radius A1-465 Permissible Error of the Mounting Surface A1-467 Flatness of the Mounting Surface A1-468 Dimensions of Each Model with an Option Attached A1-484
14
Embed
Caged Ball LM Guide Miniature Type Model · PDF fileA1-149 LM Guide SRS Structure and Features Caged Ball LM Guide model SRS has a structure where two raceways are incorporated into
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
A1-148
SRS Caged Ball LM Guide Miniature Type Model SRS
Model SRS-WM
Model SRS-M
Wide type
Compact type
Side seal
LM rail
LM block
Endplate
End seal
Ball
Ball cage
* For the ball cage, see A1-88 .
Point of Selection A1-10 Point of Design A1-450 Options A1-473 Model No. A1-537 Precautions on Use A1-543 Accessories for Lubrication A24-1 Mounting Procedure and Maintenance B1-89
Equivalent moment factor A1-43
Rated Loads in All Directions A1-58
Equivalent factor in each direction A1-60
Radial Clearance A1-70
Accuracy Standards A1-83
Shoulder Height of the Mounting Base and the Corner Radius A1-465
Permissible Error of the Mounting Surface A1-467
Flatness of the Mounting Surface A1-468
Dimensions of Each Model with an Option Attached A1-484
A1-149
LM G
uideSRS
Structure and Features
Caged Ball LM Guide model SRS has a structure where two raceways are incorporated into the compact body, enabling the model to receive loads in all directions, and to be used in locations where a moment is applied with a single rail. In addition, use of ball cages eliminates friction be-tween balls, thus achieving high speed, low noise, acceptable running sound, long service life, and long-term maintenance-free operation.
[Low Dust Generation] Use of ball cages eliminates friction between balls and retains lubricant, thus achieving low dust gen-eration. In addition, the LM block and LM rail use stainless steel, which is highly resistant to cor-rosion.
[Compact] Since SRS has a compact structure where the rail cross section is designed to be low and that con-tains only two rows of balls, it can be installed in space-saving locations.
[Lightweight] Since part of the LM block (e.g., around the ball relief hole) is made of resin and formed through in-sert molding, SRS is a lightweight, low inertia type of LM Guide.
A1-150
Types and Features
Model SRS5M Specifi cation Table⇒A1-154 SRS5 is the smallest caged ball LM guide and its mounting dimensions are interchangeable with the conventional RSR5 model.
Model SRS5WM Specifi cation Table⇒A1-154
This model has a larger overall LM block length (L), width (W), rated load and permissible mo-ment than model SRS5M. Mounting dimensions are interchangeable with RSR5WM.
Model SRS-M Specifi cation Table⇒A1-156 A standard type of SRS. Note) In addition to model SRS-M, a full-ball type without
ball cage is also available.If desiring this type, indicate type “SRS-G” when placing an order.However, since SRS-G does not have a ball cage, its dynamic load rating is smaller than SRS-M. See the table of basic load ratings for SRS-G on A1-157 for details.
A1-151
LM G
uideSRS
Model SRS-WM Specifi cation Table⇒A1-158 Has a longer overall LM block length (L), a great-er width and a larger rated load and permissible moment than SRS-M. Note) In addition to model SRS-WM, a full-ball type without
ball cage is also available.If desiring this type, indicate type “SRS-G” when placing an order.However, since SRS-G does not have a ball cage, its dynamic load rating is smaller than SRS-WM. See the table of basic load ratings for SRS-G on A1-159 for details.
Model SRS-N Specifi cation Table⇒A1-156 Compared with model SRS-M , it has a longer total LM block length (L) and a higher load rat-ing and permissible moment.
Model SRS-WN Specifi cation Table⇒A1-158 Compared with model SRS-WM , it has a longer total LM block length (L) and a higher load rat-ing and permissible moment.
A1-152
Flatness of the LM Rail and the LM Block Mounting Surface
The values in Table1 apply when the clearance is a normal clearance. If the clearance is C1 clearance and two rails are used in combina-tion, we recommend using 50% or less of the value in the table.
Note) Since SRS has Gothic-arch grooves, any accuracy er-ror in the mounting surface may negatively affect the operation. Therefore, we recommend using SRS on a highly accurate mounting surface.
Table1 Flatness of the LM Rail and the LM Block Mounting Surface
Note) Since stainless steel is used in the LM block, LM rail and balls, these models are highly resistant to corrosion. To secure the LM rail of model SRS5M, use cross-recessed head screws for precision equipment (No. 0 pan head screw, class 1) M2.
Symbol for No. of rails used on the same plane (*4)
LM rail length (in mm)
Contamination protection accessory symbol (*1)
Stainless steel LM rail
Accuracy symbol (*3) Normal grade (No Symbol)/Precision grade (P)
Radial clearance symbol (*2) Normal (No symbol) Light preload (C1)
No. of LM blocks used on the same rail
Model number
2 SRS5WM UU C1 +150L P M -Ⅱ
(*1) See contamination protection accessory on A1-510 . (*2) See A1-70 . (*3) See A1-83 . (*4) See A1-13 . Note) This model number indicates that a single-rail unit constitutes one set.(i.e. If you are using 2 shafts in parallel, the required
number of sets is 2.)
A1-155
LM G
uideSRS
W
NT
M h
W1W2
H3
(K)
2-S
M1
F
LL1
φ d2
φ d1
C
SRS5WM
Unit: mm
LM rail dimensions Basic Load Rating Static permissible moment N•m * Mass
Note) The maximum length under “Length * ” indicates the standard maximum length of an LM rail. (See A1-160 .) Static Permissible Moment * 1 block: Static permissible moment value with 1 LM block Double blocks: static permissible moment value with 2 blocks closely contacting with each other
● Reference bolt tightening torque when mounting an LM block for model SRS 5M/5WM is shown inthe table below.
Reference tightening torque
Model No. Model No. of screw Screw depth (mm) Reference tightening torque (N•m) *
SRS 5M M2 1.5 0.4
SRS 5WM M3 2.3 0.4
* Tightening above the tightening torque affects accuracy. Be sure to tighten at or below the defi ned tightening torque.
Model number coding
A1-156
Models SRS-S, SRS-M and SRS-N 4-S×ℓ
W2
W
N
TM (K)
H3
B
W1
Model No.
Outer dimensions LM block dimensions
Height Width Length
M W L B C S×ℓ L 1 T K N H 3
SRS 7M 8 17 23.4 12 8 M2×2.3 13.4 3.3 6.7 1.6 1.3
SRS 9XS SRS 9XM SRS 9XN
10 20 21.5 30.8 40.8
15 — 10 16
M3×2.8 10.5 19.8 29.8
4.5 8.5 2.4 1.5
SRS 12M SRS 12N 13 27 34.4
47.1 20 15 20 M3×3.2 20.6
33.3 5.7 11 3 2
SRS 15M SRS 15N 16 32 43
60.8 25 20 25 M3×3.5 25.7
43.5 6.5 13.3 3 2.7
SRS 20M 20 40 50 30 25 M4×6 34 9 16.6 4 3.4
SRS 25M 25 48 77 35 35 M6×7 56 11 20 5 5
Note) Since stainless steel is used in the LM block, LM rail and balls, these models are highly resistant to corrosion and environment.
Symbol for No. of rails used on the same plane (*4)
LM rail length (in mm)
Contamination protection accessory symbol (*1)
Stainless steel LM rail
Accuracy symbol (*3) Normal grade (No Symbol)/High accuracy grade (H) Precision grade (P)
Radial clearance symbol (*2) Normal (No symbol) Light preload (C1)
No. of LM blocks used on the same rail
With QZ Lubricator
Model number
2 SRS20M QZ UU C1 +220L P M -Ⅱ
(*1) See contamination protection accessory on A1-510 . (*2) See A1-70 . (*3) See A1-83 . (*4) See A1-13 .
Note) This model number indicates that a single-rail unit constitutes one set. (i.e., required number of sets when 2 rails are used in parallel is 2 at a minimum.) Those models equipped with QZ Lubricator cannot have a grease nipple.
A1-157
LM G
uideSRS
h
F
M1
φ d1
φ d2
L1
C
L
Unit: mm
LM rail dimensions Basic load rating Static permissible moment N-m * Mass
Note) If a grease nipple is required, indicate “with grease nipple”. (available for models SRS 15M/15N/15WM/15WN/20M/25M) If a greasing hole is required, indicate “with greasing hole”. (available for models SRS 7M/7WM/9WM/9WN/12M/12N/12WM/12WN) The maximum length under “Length * ” indicates the standard maximum length of an LM rail. (See A1-160 .) Static Permissible Moment * 1 block: static permissible moment value with 1 LMblock Double blocks: static permissible moment value with 2 blocks closely contacting with each other
● Reference bolt tightening torque when mounting an LM block for model SRS 7M is shown in the table below. Reference tightening torque
Model No. Model No. of screw Screw depth (mm) Reference tightening torque (N•m) * SRS 7M M2 2.3 0.4
* Tightening above the tightening torque affects accuracy. Be sure to tighten at or below the defi ned tightening torque.
Model number coding
A1-158
Models SRS-WM and SRS-WN
Models SRS7WM/9, 12WM/WN Models SRS15WM/WN
N N
4-S×ℓ4-S×ℓ
W1 W2
W3
W2 W1
W
T M (K)
H3 H3
B
W
M T
(K)
B
Model No.
Outer dimensions LM block dimensions
Height Width Length
M W L B C S×ℓ L 1 T K N H 3
SRS 7WM 9 25 31 19 10 M3×2.8 20.4 3.8 7.2 1.8 1.8
SRS 9WM SRS 9WN 12 30 39
50.7 21 23
12 24 M3×2.8 27
38.7 4.9 9.1 2.3 2.9
SRS 12WM SRS 12WN 14 40 44.5
59.5 28 15 28 M3×3.5 30.9
45.9 5.7 11 3 3
SRS 15WM SRS 15WN 16 60 55.5
74.5 45 20 35 M4×4.5 38.9
57.9 6.5 13.3 3 2.7
Note) Since stainless steel is used in the LM block, LM rail and balls, these models are highly resistant to corrosion and environment.
Symbol for No. of rails used on the same plane (*4)
LM rail length (in mm)
Contamination protection accessory symbol (*1)
Stainless steel LM rail
Accuracy symbol (*3) Normal grade (No Symbol)/High accuracy grade (H) Precision grade (P)
Radial clearance symbol (*2) Normal (No symbol) Light preload (C1)
No. of LM blocks used on the same rail
With QZ Lubricator
Model number
2 SRS15WM QZ UU C1 +550L P M -Ⅱ
(*1) See contamination protection accessory on A1-510 . (*2) See A1-70 . (*3) See A1-83 . (*4) See A1-13 .
Note) This model number indicates that a single-rail unit constitutes one set. (i.e., required number of sets when 2 rails are used in parallel is 2 at a minimum.) Those models equipped with QZ Lubricator cannot have a grease nipple.
A1-159
LM G
uideSRS
h
F
M1
φ d1
φ d2
L1
C
L
Unit: mm
LM rail dimensions Basic load rating Static permissible moment N-m * Mass
Note) If a grease nipple is required, indicate “with grease nipple”. (available for models SRS 15M/15N/15WM/15WN/20M/25M) If a greasing hole is required, indicate “with greasing hole”. (available for models SRS 7M/7WM/9M/9N/9WM/9WN/12M/12N/12WM/12WN). The maximum length under “Length * ” indicates the standard maximum length of an LM rail. (See A1-160 .) Static Permissible Moment * 1 block: static permissible moment value with 1 LMblock Double blocks: static permissible moment value with 2 blocks closely contacting with each other
SRS-G (Full-ball Type) Basic Load Ratings
Model No. Basic load rating C C 0 kN kN
SRS 7WGM 1.63 2.51
SRS 9WGM 2.67 3.35
SRS 12WGM 4.46 5.32
SRS 15WGM 7.43 8.59
● Reference bolt tightening torque when mounting an LM block for model SRS 7WM is shown in the table below. Reference tightening torque
Model No. Model No. of screw Screw depth (mm) Reference tightening torque (N•m) * SRS 7WM M3 2.8 0.4
* Tightening above the tightening torque affects accuracy. Be sure to tighten at or below the defi ned tightening torque.
A1-160
Standard Length and Maximum Length of the LM Rail
Table2 shows the standard lengths and the maximum lengths of model SRS variations. If the maxi-mum length of the desired LM rail exceeds them, jointed rails will be used. Contact THK for details. For the G dimension when a special length is required, we recommend selecting the corresponding G value from the table. The longer the G dimension is, the less stable the G area may become after installation, thus causing an adverse impact to accuracy.
G L0
F F G
Table2 Standard Length and Maximum Length of the LM Rail for Model SRS Unit: mm
Standard pitch F 15 20 15 30 20 30 25 40 40 40 60 60 G 5 5 5 10 7.5 10 10 15 15 15 20 20
Max length 220 220 480 480 1240 1430 1430 1600 1600 1800 1800 1800 Note1) The maximum length varies with accuracy grades. Contact THK for details. Note2) If jointed rails are not allowed and a greater length than the maximum values above is required, contact THK.
A1-161
LM G
uideSRS
Greasing Hole
[Grease Nipple and Greasing Hole for Model SRS] The standard version of Model SRS is not equipped with either a grease nipple or an oil hole. Grease nipple installation and greasing hole drilling are performed at THK. When ordering SRS, in-dicate that the desired model requires a grease nipple or greasing hole. Model SRS-G (full-ball type) has a grease nipple and a greasing hole as standard. (For greasing hole dimensions and supported grease nipple types and dimensions, see Table3 .) When using SRS under harsh conditions, use QZ Lubricator* (optional) or Laminated Contact Scraper LaCS* (optional). Note1) Grease nipple is not available for models SRS5M, SRS5WM, SRS7M, SRS7WM, SRS9XS, SRS9XM, SRS9XN, SR-
S9WM, SRS12M and SRS12WM. They can have a greasing hole. Note2) Using a greasing hole other than for greasing may cause damage. Note3) For QZ Lubricator*, see A1-502 . For Laminated Contact Scraper LaCS*, see A1-479 . Note4) When desiring a grease nipple for a model attached with QZ Lubricator, contact THK.
End seal
End seal L E
Fig.1 Dimensions of the Grease Nipple for Model SRS
Note) For the L dimension, see the corresponding specifi ca-tion table.
Table3 Table of Grease Nipple and Greasing Hole Dimensions