metal made easy www.industrialmetalsupply.com Ready to Install Cable Assemblies Includes one Invisiware ® with Swaged Threaded Ferrule tensioning end and one Pull-Lock ™ fixed end. Install the Cable and field trim after tensioning. CABLE ASSEMBLIES INCLUDE: • Fittings for both ends of your Cable run • All Washers and Fasteners necessary • 3⁄16” Diameter, Type 316 Stainless Steel Cable • Instructions Los Angeles 818-729-3333 Inland Empire 951-300-9900 Orange County 949-250-3343 San Diego 858-277-8200 Phoenix 602-454-1500 Tucson 520-441-5161
3
Embed
CABLE RAIL - Industrial Metal Supply · CABLE RAIL CABLE ASSEMBLIES INCLUDE: • Fittings for both ends of your Cable run • All Washers and Fasteners necessary • 3⁄16” Diameter,
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
metal made easy
www.industrialmetalsupply.com
Ready to Install Cable AssembliesIncludes one Invisiware® with Swaged Threaded Ferrule tensioning end and one Pull-Lock™ fi xed end.
Install the Cable and fi eld trim after tensioning.
Field installed Pull-Lock fittingsmake installing cables easy.
No field swaging Pull-Lockfittingsaredesignedforusewith1x19left- hand-laystrandonly.Easy to install 1.InserttheInvisiware Receiver with Swaged Threaded Ferrule on one End Post. 2.SlipthePull-Lock fitting into the other End PostandpulltheCable all the waythroughthePull-Lock fitting. 3.TensiontheCablethencut the excess Cable off on the back side of the fitting with a4”rightanglegrinder or a cutting wheel (CRCUTOFFKIT) used with a hand drill.
How to Order: Determine your Railing frame materials–woodormetal–andthewidthordiameterofyourEndPost–Posts to which tensioning and other mounting hardware will be attached.
Measure the length of each Cable run:• Addatleast6inchestoyourmeasurement.• OrdertheassembliesinCablelengthincrementsof10, 20or30feet–toprovidesufficientCableforeachof yourCableruns. Cablewillbecuttoproperlengthonsite.Order Cable Cutter and other tools separately – as required.
MakesurehalfoftheThreadedFerrule’sthreadsare visible so that there is enough draw in the ReceivertoproperlytensiontheCable.
3⁄16” Cable Pull-Lock with 2” Long Invisiware Receiver
Tupe 316,Stainless Steel Length
CR2326-10 10’
CR2326-20 20’
CR2326-30 30’
Pull-LockInstall Video
InvisiwareInstall Video
3⁄16”Stainless
SteelCable
Delrin®WashersForUseWithMetal Posts
StainlessSteelWashersforUseWithWoodPosts
InvisiwareReceiver
Pull-LockFittingW/Cap
SURFACE MOUNT POSTS FACIA MOUNT POSTS
Co
rner
Po
st
Co
rner
Po
st
Inte
rmed
iate
Po
st
Inte
rmed
iate
Po
st
En
d P
ost
En
d P
ost
CABLE CLAMPBolts onto cable to minimize Cable flex.
Satin Stainless CRCC188-12
SATIN FINISH POST TYPE MOUNT CABLE LINES TYPE 304 STAINLESS STEEL Corner Post Fascia Mount 12 CR190SS42CF Intermediate Post Fascia Mount 12 CR190SS42LF End Post Fascia Mount 12 CR190SS42EF Corner Post Surface Mount 12 CR190SS42CS Intermediate Post Surface Mount 12 CR190SS42LS End Post Surface Mount 12 CR190SS42ES
In order to meet load requirements, these Posts should bespaced4 to5 feetoncenterwithaCableClamp insertedatthe mid-point between Posts. With this configuration, Cablesneedtoonlybetensionedto200lbs.Thesystemwillonlybeasstrongasthestructuretowhichitisattached.Youmayneedreinforcementinyourexistingstructuretoassureperformance.
End Intermediate CornerPost Cable Clamp Post Cable Clamp Post
CAST ELBOWS AND TEEThesecastStainlessSteelFittingsaredesignedtopermitweld-freeassemblyofWagnerailsystems.ComponentsarejoinedtoTopRailandPostsusingEpoxy.