CA-NV AWWA 2013 Fall Conference · 2013. 10. 2. · 10/2/2013 11 Setting Pump Stroke and Speed Try to keep stroke length at largest setting. Adjust the pump speed for flow rate. Using

Chemical Metering Pump, Accessories

and Systems.

By

Richard Hopkins

Hopkins Technical Products, Inc

CA-NV AWWA

2013 Fall Conference

10/2/2013 22

Mathematics

Equation #: 1 for Chlorine

Flow(MGD) x Dosage(mg/l) x 3.785/gal x 1,000,000

Liquid (mg/ml) x (24 hr/day) x 60 minutes/Hours

2 x 2 x 3.785 x 1,000,000

315.16 x 24 x 60

33.36 PPD

10/2/2013 33

Mathematic

Equation #: 2

GPM x Dosage x 1440 / Concentration

1388.88 x 2 x 1440 / 120000

33.33

10/2/2013 44

Mathematics

Equation #: 3

Feed Rate (lbs/day) = Chlorine Demand (MGDl) X

Dosage (mg/l) X 8.34 lb/gal.

2 MGD X 2 mg/l X 8.34

33.36 PPD

10/2/2013 55

Mathematic

Equation #: 4

GPM X 0.012 X Dosage

1388.88 x 0.012 x 2

33.33

10/2/2013 66

Mathematic

Equation Any Chemical for 1 PPM

Millions Gallons Per Day

Concentration

2

0.120

16.66 Gallons x 2 = 33.33 Gallons Per Day

10/2/2013 77

Mathematic Equations

Flow(MGD) x Dosage(mg/l) x 3.785/gal x 1,000,000

Liquid (mg/ml) x (24 hr/day) x 60 minutes/Hours

GPM x Dosage x 1440 / Concentration

Feed Rate (lbs/day) = Chlorine Demand (MGDl X

Dosage (mg/l) X 8.34 lb/gal.

GPM X 0.012 X Dosage

Millions Gallons Per Day

Concentration

10/2/2013 88

Mathematics

What did the equations have in common?

33.3 Pounds Per Day

10/2/2013 99

Pump Sizing

GPM x 0.012 x PPM – Pounds Per Day Chlorine

Well Flow Rate – 1388.89 GPM

Dosage – 2.0 Parts per Million

How much Chlorine do we need?

1388.89 GPM x 0.012 x 2 =

33.33 Pounds per Day.

33.33 / 24 hours

Or 1.38889 GPH.

10/2/2013 1010

Pump Selection

10/2/2013 1111

Setting Pump Stroke and Speed

Try to keep stroke length at largest setting.

Adjust the pump speed for flow rate.

Using the previous example we needed 1.39 GPH.

Pump capacity selected was 1.66 GPH.

Feed Rate / Pump Capacity = Pump Percentage

1.39 GPH / 1.66 GPH = 84%

Metering Pump has 180 SPM so we set the

pump speed at (180 SPM x 84%) = 151 spm.

Or adjust the stroke length to 84%

10/2/2013 1212

Chemical Metering Systems

What is the minimum equipment requirements

needed for a chemical metering system?

Pump.

Tank.

10/2/2013 1313

Pump Installation

10/2/2013 1414

Pump Installation

10/2/2013 1515

Pump Installation

10/2/2013 1616

Pump Installation

10/2/2013 1717

Pump Installation

10/2/2013 1818

Seismic Restrained Pump Installation

10/2/2013 1919

Pump Installation

10/2/2013 2020

Tank and a Pump

Does this work?

Is this the best installation?

What are the potential problems?

Inconsistent Feeding.

Over Pressuring System.

General Maintenance.

10/2/2013 2121

Pump Accessories

Back Pressure Valve.

Pressure Relief Valve.

Multi-function Valve.

Calibration Column.

Pulsation Dampener.

Inlet Stabilizers.

Y-Strainers/Basket Strainers.

Pressure Gauge.

Pressure Switch.

Flow Meter / Sensor

10/2/2013 2222

Back Pressure Valves

Positive Discharge Pressure.

Prevents Anti-Siphoning.

Eliminates Varying Dosage Rates.

Install Close to Injection Point to Prevent

Chemical Line Siphoning

Prevents Back Flow.

10/2/2013 2323

Back Pressure Valve

10/2/2013 2424

Pressure Relief Valve

Designed to Protect Chemical Feed System from

over pressuring caused by defective equipment and

blockage.

Relief port back to chemical tank or pump suction

side.

Off-Gassing Chemical will require a PRV between

valves.

10/2/2013 2525

Pressure Relief Valve

10/2/2013 2626

Multi-Function Valve

Mounts directly on liquid end of pump.

Back Pressure.

Pressure Relief.

Anti-siphon.

Priming.

Draining the discharge line.

10/2/2013 2727

Calibration Column

Installed to enhance performance of your chemical

feed system by providing verifying flow rates of the

chemical feed pump.

10/2/2013 2828

Calibration Column

10/2/2013 2929

Pulsation Dampener

Why use a Pulsation Dampener?

Positive Displacement pumps create pulsation

and hydraulic shock due to the reciprocating

nature of their stroking action, potentially

damaging the entire pumping system.

10/2/2013 3030

Pulsation Dampener

Reduces pump pulsation and pipe vibration up to

99%.

Protects Pipes, Valves, Fittings, Meters and In-Line

Instrumentation from destructive pulsations,

vibrations, surges, cavitation, thermal expansion

and water hammer.

Produce an even and smooth flow (Pressure

Gauges and flow meters).

Extend pump component life and improve pump

performance.

Insures accuracy, longevity and repeatability of In-

Line Meters.

10/2/2013 3131

Pulsation Dampener

Manufacturer’s Installation Requirements:

Install Dampener in-line as close as possible to

the pump discharge.

Installation should be no more than 10 pipe

diameters from the pump discharge.

Isolation Valve should be installed between the

dampener and pump.

10/2/2013 3232

Pulsation Dampener

10/2/2013 3333

Pulsation Dampener – Peristaltic Pump

10/2/2013 3434

Pulsation Dampener

10/2/2013 3535

Inlet Stabilizer

Why use an Inlet Stabilizer?

Positive Displacement pumps contain an inlet

valve that alternately opens and closes, creating

an acceleration and deceleration of fluid into the

pump.

Under High Pressure – Liquid flow is abruptly

stopped as the inlet valve closes. Rapid

deceleration creates a pressure spike or “Water

Hammer”.

10/2/2013 3636

Inlet Stabilizer

Under Low Pressure – Process fluid separate at

the pump’s inlet as the inlet valve closes. May

not be enough to meet required pump’s inlet

pressure and may result in product starvation or

“cavitation”.

10/2/2013 3737

Inlet Stabilizer

Use an Inlet Stabilizer to:

Ensure complete chamber fill extending

component service life.

Protects pumps, valves and diaphragms from

excess stress and strain.

Prevents unbalanced hydraulics from friction,

acceleration and head (Starvation).

Prevents premature system component failure.

Extends diaphragm life in all diaphragm pumps.

10/2/2013 3838

Inlet Stabilizer

Manufacturer’s Installation Requirements:

Install as close to pump inlet as possible.

Upstream of any valves, elbows and filters.

No more than 10 pipe diameters from pump inlet.

10/2/2013 3939

Inlet Stabilizer

10/2/2013 4040

Wye / Basket Strainer

Removes sedimentation from fluid that may plug the

pump check valves.

10/2/2013 4141

Pressure Gauge / Switch

Best troubleshooting device in the system. Displays

system pressure.

Pressure Switch will shut system off if exceeds set

point for protection.

Pressure Switch set-point?

10/2/2013 4242

Piping

Check chemical compatibility. Where to Check?

Piping / Material

Sch. 80 PVC, CPVC, Polypro, PVDF, 316SS,

Alloy 20, Etc.

Check elastomer compatibility.

Viton, EPDM, PTFE.

Valves

Ball Valves (Vented or Non-vented), diaphragm

Valves

End Connections

Threaded, socket, flanged.

10/2/2013 4343

What is wrong

You decide

10/2/2013 4444

Engineers Drawing

10/2/2013 4545

Contractor’s Installation

10/2/2013 4646

What’s Wrong

10/2/2013 4747

Inlet Stabilizer

10/2/2013 4848

Pump Installation

10/2/2013 4949

FET UP!

10/2/2013 5050

Pump Installation

10/2/2013 5151

Pump Installation

10/2/2013 5252

What is the Red Hose

10/2/2013 5353

10 lbs in a 5lb building

10/2/2013 5454

What’s Wrong

10/2/2013 5555

What is wrong

10/2/2013 5656

What is wrong

10/2/2013 5757

What’s wrong

10/2/2013 5858

Questions

Any Questions

10/2/2013 5959

Thank you

Thank you