Page 1
Operating Parameters
Standard cylinders
Working pressure 250 bar
External sea pressure - Cepac subsea cylinders
350 bar depth : 3500 metres
Temperature range -10°C to +80°C
Hydraulic fluid All good quality mineral oils, water in oil emulsions, water glycols and 95/5 HWB fluids
Rod speed 500mm/sec maximum with mineral oil at working pressure
Rec filtration NAS 1638 class 10 (ISO 19/16) or 25 micron absolute
Materials of construction
Tubes Dom 1026 or ST52 steel, honed to 0.4µm Ra. minimum UTS 580 N/mm2
Rods - C10 BS 970: 080M40 steel hard chrome plated to depth of 0.025mm and polished to
0.15µm Ra. minimum UTS 550N/mm2
Rods - Cepac BS 970: 431 S29T hardened and tempered, stress relieved stainless steel hard chrome
plated to depth of 0.025mm and polished to 0.15µm Ra. minimum UTS 850N/mm2
Note
The above parameters apply to cylinders within the standard range of C10 and Cepac cylinders manufactured by the company. Custom built cylinders are supplied to meet other specifications including higher operating pressures, temperatures and fire resistant fluids.
Application
Check that the cylinder application is the same as when the cylinder was ordered. Special attention should be given to the load-carrying capacity. Long cylinders, particularly with rear mountings have limited load- carrying capacity due to their ‘strut’ strength. Consequently, cylinders are selected in accordance with the APH buckling charts on pages B6 and B7, thereby ensuring the correct size of rod necessary to transmit the required thrust at full stroke.
Attention should also be paid to support tubes which are necessary to avoid high mechanical load on piston seals and gland bushings.
C10-CEP-OP
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825 Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
B2
CYLINDERS C10 & CEPAC
OPERATING PARAMETERS
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
B2
Page 2
Installation
Mounting the cylinders
1 Where cylinders are supplied for rigid mounting,
ensure that the direction of travel of the load
connected to the piston rod exactly aligns with the
piston rod travel. If not, provision must be made for
axial misalignment.
2 Flange mounted cylinders should be solidly mounted to
a rigid section of the machine using high-tensile bolts
(socket head type recommended). Where a spigot
diameter cannot be used to locate the cylinder, it must
be accurately aligned to the work, tightened in place,
and the flange drilled for a dowel pin to prevent axial
movement.
3 Standard clevis and trunnion mounted cylinders are
designed for pivoting in one plane only. It is therefore
essential that these cylinders are accurately aligned
throughout their operating arc thereby avoiding
excessive side loading. Where accurate alignment is
not possible, the cylinder must be equipped with two-
directional pivoting at both ends eg swivel eye
mountings.
4 When fitting trunnion mounted cylinders, pillow-
blocks of adequate dimensions should be rigidly
mounted as close as possible to the trunnion faces.
Bearings must be provided over the full length of the
trunnion pins and lubrication provided to the bearing
interface.
Storage
If it is necessary to store cylinders prior to installation, the
following provisions should be made for their protection:
1 Cylinders should be stored indoors in a clean, dry
environment with the rod retracted. Where this is not
possible, and they are likely to be exposed to dampness
or other corrosive atmospheres, all unpainted external
parts, including the piston rod, must be coated with a
corrosion inhibiting material. In addition, both ends of
the cylinder should be filled with a corrosion resistant
fluid which is compatible with the operating fluid.
2 Where possible, the cylinders should be stored in a
vertical position with the piston rod upwards.
3 Dirt-protection plugs must be left in the ports during
storage.
C10-CEP-INST
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265
Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
B3
CYLINDERS C10 & CEPAC
INSTALLATION
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
B3
Page 3
Cylinders
Pencyl Cylinders Operating Parameters
Standard cylinders
Working pressure 350 bar
Temperature range -40°C to +80°C
Hydraulic fluid All good quality mineral oils, water in oil emulsions, water glycols, 95/5 HWB fluids and fresh water
Seal material Medium nitrile rubber (Buna N) and polyurethane or PTFE depending on fluid
Rod speed 500mm/sec maximum with mineral oil at working pressure
Rec filtration NAS 1638 class 10 (ISO 19/16) or 25 micron absolute
Materials of construction - Pencyl
External parts BS 970 316S11 stainless steel
Internal parts NES 833 aluminium bronze or equivalent
Rod BS 970 431S29T hardened and tempered, stress relieved stainless steel hard chrome
plated to depth of 0.025mm and polished to 0.15µm Ra. minimum UTS 850N/mm2
Materials of construction - Pencyl Lite
External parts 6082 T6 hard anodised aluminium alloy
Internal parts NES 833 aluminium bronze or equivalent
Rod BS 970 431S29T hardened and tempered, stress relieved stainless steel hard chrome
plated to depth of 0.025mm and polished to 0.15µm Ra. minimum UTS 850N/mm2
Note
The above parameters apply to cylinders within the standard range of Pencyl and Pencyl Lite cylinders manufactured by the company. Custom built cylinders are supplied to meet other specifications including higher operating pressures, temperatures and special fluids.
PEN-OP
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825 Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
CYLINDERS PENCYL
OPERATING PARAMETERS
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
B4
Page 4
Cylinders
C10 & Cepac Cylinders Electronic Rod Position Indication
Introduction
Air Power & Hydraulics first introduced Internal
Electronic Rod Position Indication in 1990. Since then the
range of transducers has increased making it possible now
to offer our 18 series cylinder - 32mm bore x 18mm rod
- incorporating a VRVT type transducer with up to 300mm
of stroke.
The sectional drawing above is typical of the whole range
of our cylinders with Electronic Rod Position Indication
and shows a 48 series Cepac subsea cylinder with
transducer and straight subsea connector.
Transducer models available
Penny & Giles VRVT type transducer with loose electronic modules
to handle all standard input and output signals.
Accuracy: ± 0.2% of electrical stroke. Maximum stroke: 1000mm.
Rota multiple reed switch transducer giving variable output voltage
signal of 0.5v to 5.0v DC (4 to 20 mA optional) with input of 12v to
24v DC.
Signal resolution: 3, 5 or 10mm. Maximum stroke : 4000mm. Temposonics III and Balluff robust design magnetostrictive transducers
with on board digital or analog electronics for high accuracy and long
stroke applications.
Analog resolution: Infinite. Digital resolution: 0.1 mm, 0.01 mm or 0.0025mm max. Maximum stroke: 7500mm.
Features
Available with C10 heavy duty and Cepac marine & subsea cylinders.
Stroke indication to client specification.
Available currently with all cylinders from 32mm to 250mm bore.
Suitable for system pressures up to 350 bar.
Water-tight connectors for subsea applications.
Suitable for use with all standard mineral oils, water glycols and
HWB (95/5) fluids and [inhibited] water.
Options
Output connector can be 90º type and positioned at an angle to
the rear port.
Ported rod cylinders available with all types of transducer.
Electronic packages available for computer control including
interconnecting cabling and plugs.
Cartridge valves such as dual overcentre, pilot-operated check and
flow controls can be incorporated in the cylinder end cap with a fully
welded transfer tube to the annular port for operation in extremely
arduous conditions.
ERP1
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265
Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
CYLINDERS C10 & CEPAC
ELECTRONIC ROD POSITION
INDICATION
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
B5
Page 5
Cylinders
C10, Cepac & K10 Cylinders Stroke / Buckling length limits
Chart A
Piston rod selection
The standard catalogue cylinder/rod diameter combinations are suitable for most applications but the
tendency for "long" rods to buckle under compressive loads should always be considered. In these
circumstances, selection of the piston rod diameter
should be determined prior to finalising the mounting style.
The optimum rod diameter is established with the following procedure:-
1 Calculate the cylinder push force “P” (tonnes) available
by multiplying the cylinder full bore area (cm2) by the maximum pressure (bar) to be applied to the cylinder
(please refer to technical bulletin - areas and performance data on pages C1 & D1).
2 Relating the cylinder mounting style to chart A,
establish the distance "E" and hence the buckling length "Lb" in metres.
3 Using this value of Lb in chart B on page B7, follow its
line vertically up till it intersects the horizontal line representing the cylinder push force in tonnes. The
correct piston rod diameter can now be read from the curved line immediately above the point of interestion.
Internal support (stop) tube
Long stroke cylinders are fitted with an internal stop tube between the piston and gland assembly (or in special
circumstances an additional piston); this increases bearing spread hence reducing the bearing load, especially at full
stroke.
The stop tube length (if required) can be established with the following procedure:-
1 Relate the cylinder mounting style to chart A, establish
the distance "E" and hence the buckling length "Lb" in metres.
2 If "Lb" is less than 1 metre, no stop tube is required.
3 If "Lb" is greater than 1 metre, 25 mm of stop tube is
recommended for every 250 mm (or part thereof)
beyond 1 metre.
Note carefully: Stop tube length adds to basic cylinder
length.
C10-CEP-K10-A
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
P P P P P P P P
Lb = 0.7E Lb = 2E
B6
E
E
E
E
E
E
E
E
CYLINDERS C10 & CEPAC
STROKE / BUCKLING LENGTH
LIMITS
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
B6
Page 6
Cylinders
C10, Cepac & K10 Cylinders Piston rod buckling chart
Chart B
C10-CEP-K10-B
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
Chart values based on a factor of safety of 3 on buckling
1000
900
700
500
350
250
1000
800
600
400
300
200
150
100 90
70
50
35
25
100
80
60
40
30
20
15
10 9.0
10
0.50
0.35
BUCKLING Lb IN METERS
B7
PER
MIS
SIB
LE P
USH
ING
FO
RC
E P
IN
TO
NN
ES
CYLINDERS C10 & CEPAC
PISTON ROD BUCKLING CHART
(CHART B)
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
B7
Page 7
Areas and Performance Data
Cylinder sizes
SERIES
BORE
mm in
ROD
mm in
BORE
cm2 in2
AREA
ROD
cm2 in2
ANNULUS
cm2 in2
12 28.58 1.125 12.70 0.50 6.415 0.994 1.267 0.196 5.148 0.798
18 31.75 1.25 18 0.71 7.95 1.23 2.55 0.39 5.40 0.84
21 50.8 2 25.4 1 20.32 3.14 5.08 0.78 15.24 2.36
28 63.5 2.5 31.75 1.25 31.75 4.91 7.93 1.23 23.82 3.68
35 76.2 3 44.45 1.75 45.72 7.07 15.55 2.41 30.17 4.66
38 80 3.15 56 2.20 50.27 7.79 24.63 3.82 25.64 3.97
48 100 3.94 63.5 2.50 78.75 12.19 31.75 4.91 47.00 7.28
52 125 4.92 70 2.76 123.04 19.01 38.58 5.97 84.46 13.04
63 152.4 6 88.9 3.50 182.90 28.27 62.07 9.62 120.67 18.65
65 160 6.30 88.9 3.50 201.06 31.16 62.07 9.62 139.00 21.55
85 200 7.87 110 4.33 315.00 48.70 95.28 14.73 219.72 33.97
100 250 9.84 160 6.30 491.00 76.08 201.06 31.16 290.00 44.92
Conversions
Forces
CEP-PERF
1 c m 2 = 0.155 i n 2
1 i n 2 = 6.452 c m 2
1 bar = 1.020 Kg /c m 2 = 14.504 lb/ i n 2
1 Kg/c m 2 = 0.980 bar = 14.233 lb/ i n 2
1 at m = 1.033 Kg/c m 2 = 14.700 lb/ i n 2
1 lbf = 4. 4 50 N
1 bar = 0. 100 Mega Pascals (M Pa)
CYLINDERS MARINE & SUBSEA
AREAS & PERFORMANCE DATA
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D1
PUSH FORCE (tonnes) = BORE AREA (cm 2) x PRESSURE (bars)
1000
PULL FORCE ( tonnes) = ANNULAR AREA ( cm 2) x PRESSURE (bars)
1000
PUSH FORCE ( tons) = BORE AREA ( in 2) x PRESSURE ( lb / in 2)
2240
PULL FORCE (tons) = ANNULAR AREA ( in 2) x PRESSURE ( lb / in 2)
2240
Page 8
Weights (Kg)
Cylinder weights
SERIES
BORE
ROD
BASE WEIGHT
ZERO STROKE
Kg
REAR EYE
RE-SERIES
Kg
REAR FLANGE
RF SERIES
Kg
FRONT FLANGE
FF-SERIES
Kg
FOOT
FT-SERIES
Kg
TRUNNION
TN-SERIES
Kg
ADD PER MM
OF STROKE
Kg
12 28.58 12.70 .72 .12 .47 .40 .17 .34 .0035
18 31.75 18 .70 .15 .30 .30 .20 .50 .0047
21 50.8 25.4 2.50 .40 .50 1.20 .70 1.50 .0106
28 63.5 31.75 4.50 .80 .50 1.50 1.50 3.50 .0177
35 76.2 44.45 7.50 .90 2.0 4.2 2.5 3.0 .0255
38 80 56 10.0 1.80 6.5 5.0 4.9 4.2 .0355
48 100 63.5 16.50 3.5 8.5 5.5 6.5 6.5 .0457
52 125 70 30.0 5.4 11.0 8.0 11.0 10.0 .0657
63 152.4 88.9 45.0 6.4 15.0 10.0 14.0 20.0 .0886
65 160 88.9 49.0 9.3 25.0 20.0 21.0 26.0 .0907
85 200 110 107 19.5 31.5 29.2 29.3 42.0 .1401
100 250 160 216 39.5 71.5 69.4 62.2 68.0 .2492
Accessory weights
SERIES BORE ROD SCREWED ROD EYE
Kg
WELDED ROD EYE
Kg
SPHERICAL ROD EYE
Kg
FORK CLEVIS
Kg
12 28.58 12.70 - .20 .20 .073
18 31.75 18 .20 .10 .20 .22
21 50.8 25.4 .62 .35 .40 .72
28 63.5 31.75 1.40 .75 .80 1.34
35 76.2 44.45 1.23 1 .80 1.34
38 80 56 2.40 1.80 1.20 4.30
48 100 63.5 4.11 3.50 2.80 -
52 125 70 6.36 6.00 4.30 -
63 152.4 88.9 8.10 6.00 5.00 -
65 160 88.9 11.0 9.30 8.50 -
85 200 110 25 19.5 16 -
100 250 160 50 39.5 27 -
CEP-WTS
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265
Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
D2
CYLINDERS MARINE & SUBSEA
WEIGHTS
(KG)
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D2
Page 9
Cylinder Section Series 12-21
ITEM DESCRIPTION ITEM DESCRIPTION
1 CYLINDER BODY *9 GLAND ROD SEAL
2 PISTON *10 SCRAPER RING SEAL
3 PISTON ROD *11 GLAND SEAL
4 GLAND *12 ROD / PISTON SEAL
5 GLAND RING *13 WIPER SEAL
6 SCRAPER RING *14 GLAND RING SEAL
*7 PISTON SEAL *15 RETAINING PIN
*8 SCRAPER RING ROD SEAL
Rear eye mounting style shown * Seal kit items For Surface Marine cylinders omit items 6,8 and 10
CEP-12-21-SEC
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265
Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
3 13 5 14 10 6 11 8 9 4 12 7 1 2 15
D3
CYLINDERS MARINE & SUBSEA
CYLINDER SECTION SERIES 12-21
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D3
Page 10
ITEM DESCRIPTION ITEM DESCRIPTION
1 CYLINDER BODY *9 GLAND ROD SEAL
2 PISTON *10 SCRAPER RING SEAL
3 PISTON ROD *11 GLAND SEAL
4 GLAND *12 ROD / PISTON SEAL
5 GLAND RING *13 WIPER SEAL
6 SCRAPER RING *14 GLAND RING SEAL
*7 PISTON SEAL *15 RETAINING PIN
*8 SCRAPER RING ROD SEAL
Rear eye mounting style shown * Seal kit items For Surface Marine cylinders omit items 6,8 and 10
CEP-28-SEC
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265
Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
3 13 5 14 10 6 11 8 9 4 12 7 1 2 15
D4
CYLINDERS MARINE & SUBSEA
CYLINDER SECTION
SERIES 28
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D4
Page 11
ITEM DESCRIPTION ITEM DESCRIPTION
1 CYLINDER BODY *9 GLAND ROD SEAL
2 PISTON *10 SCRAPER RING SEAL
3 PISTON ROD *11 GLAND SEAL
4 GLAND *12 ROD / PISTON SEAL
5 GLAND RING *13 WIPER SEAL
6 SCRAPER RING *14 GLAND RING SEAL
*7 PISTON SEAL *15 RETAINING PIN
*8 SCRAPER RING ROD SEAL
Rear eye mounting style shown * Seal kit items For Surface Marine cylinders omit items 6,8 and 10
CEP-35-SEC
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265
Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
13 14 10 6 8 11 9 4 12 7 2 15
D5
CYLINDERS MARINE & SUBSEA
CYLINDER SECTION SERIES 35
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D5
Page 12
Cylinder Section
Series 48-85
ITEM DESCRIPTION ITEM DESCRIPTION
1 CYLINDER BODY *8 ROD SEAL
2 PISTON *9 SCRAPER RING SEAL
3 PISTON ROD *10 GLAND SEAL
4 GLAND *11 ROD / PISTON SEAL
5 GLAND RING *12 WIPER
6 SCRAPER RING *13 GLAND RING SEAL
*7 PISTON SEAL *14 RETAINING PIN
Rear eye mounting style shown * Seal kit items For Surface Marine cylinders omit items 6,8 and 9
CEP-48-85-SEC
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265
Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
12 13 6 10 8 7 11 2 1 14
D6
CYLINDERS MARINE & SUBSEA
CYLINDER SECTION
SERIES 48-85
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D6
Page 13
Cylinder Section Series 100
ITEM DESCRIPTION ITEM DESCRIPTION
1 CYLINDER BODY *8 ROD SEAL
2 PISTON *9 SCRAPER RING SEAL
3 PISTON ROD *10 GLAND SEAL
4 GLAND *11 ROD / PISTON SEAL
5 GLAND RING *12 WIPER
6 SCRAPER RING *13 GLAND RING SEAL
*7 PISTON SEAL *14 RETAINING PIN
Rear eye mounting style shown * Seal kit items For Surface Marine cylinders omit items 6,8 and 9
CEP-100-SEC
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265
Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
3 12 5 9 13 8 6 10 8 4 7 11 2 1 14
D7
CYLINDERS MARINE & SUBSEA
CYLINDER SECTION SERIES 100
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D7
Page 14
Rear Swivel Eye Mounting Series 12-100 WP 250 bar
SERIES BORE ROD D2 D3 D4 D5 D6 L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 L12 L13
12 28.58 12.7 M10 35 12.7 3x5 1/8 140 19 50 46 20 13 44 28 12.7 14.3 38 32 27
18 31.75 18 1/2 38 15.87 4x6 1/4 148 19 54 48 22 13 45 30 14.3 17.5 38 32 27
21 50.8 25.4 3/4 60 19.05 5x6 1/2 197 25.5 73 66 29 17 57 45 19 22 51 38 31
28 63.5 31.75 1 76 25.4 5x6 1/2 204 31.75 75 72 38 19 57 53 25 31.75 63.5 38 31
35 76.2 44.45 11/4 89 25.4 6x8 3/4 222 38 83 76 51 22 63 60 25 31.75 76 38 29
38 80 56 M42x2 95 32 8x10 3/4 248 38 87 86 56 24 75 64 28 32 76 50 41
48 100 63.5 13/4 115 38.1 8x10 3/4 316 51 108 102 76 25 105 73 32 41 102 64 53
52 125 70 21/4 145 44.45 8x13 3/4 346 57 129 98 80 18 119 89 38 48 114 70 57
63 152.4 88.9 21/2 171 50.8 10x13 3/4 378 76 129 128 89 31 121 102 44.5 51 152 70 56
65 160 88.9 M64x3 180 60 10x13 1 388 82 129 128 90 31 131 113 50 60 164 80 62
85 200 110 3x12 230 82.5 16x25 1 494 95 149 165 89 28 180 138 70 76 190 98 77
100 250 140/160 31/2x12 278 110 20x25 1 657 130 131 288 110 50 238 162 80 90 260 146 121
Swivel eye angular movement ±10º Long stroke cylinders may require internal stop tube - refer to pages B6 and B7
Alternative rod and bore combinations available
CEP-12 -100RSE
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
D8
L7 L3 + STROKE
L12
L4
L6
D3
D6 BSP.P (RAISED REAR PORT
L2
L13 L1 + STROKE
D5
L10 OVER BALL
L9 OVER HSG
L11
D2
BSF
L8
CYLINDERS MARINE & SUBSEA
REAR SWIVEL EYE MOUNTING SERIES 12-100 WP 250 BAR
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D8
Page 15
Swivel Eye Mounting Series 12-100 WP 250 bar
SERIES BORE ROD D2 D3 D4 D5 D6 D7 L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 L12 L13 L14 L15
12 28.58 12.7 M10 35 12.7 3x5 1/8 19 140 190 50 96 50 13 44 28 12.7 14.3 38 32 19 172 27
18 31.75 18 1/2 38 15.87 4x6 1/4 25 148 205 54 106 57 13 45 30 14.3 17.5 38 32 19 180 27
21 50.8 25.4 3/4 60 19.05 5x6 1/2 35 197 267 73 137 70 17 57 45 19 22 51 38 25.4 235 31
28 63.5 31.75 1 76 25.4 5x6 1/2 40 204 274 75 142 70 19 57 53 25 31.75 63.5 38 31.75 242 31
35 76.2 44.45 11/4 89 25.4 6x8 3/4 45 222 298 83 152 76 22 63 60 25 31.75 76 38 38 260 29
38 80 56 M42x2 95 32 8x10 3/4 63.5 248 348 87 186 100 24 75 64 28 32 76 50 38 298 41
48 100 63.5 13/4 115 38.1 8x10 3/4 64 316 431 108 217 115 25 105 73 32 41 102 64 51 380 53
52 125 70 21/4 145 44.45 8x13 3/4 76 346 481 129 233 135 18 119 89 38 48 114 70 57 416 57
63 152.4 88.9 21/2 171 50.8 10x13 3/4 89 378 517 129 267 139 31 121 102 44.5 51 152 70 76 448 56
65 160 88.9 M64x3 180 60 10x13 1 90 388 538 129 278 150 31 131 113 50 60 164 80 82 468 62
85 200 110 3x12 230 82.5 16x25 1 110 494 675 149 346 181 28 180 138 70 76 190 98 95 592 77
100 250 140/160 31/2x12 278 110 - 1 125 657 898 130 530 241 50 238 162 80 90 260 146 130 803 121
Swivel eye angular movement ±10º Long stroke cylinders may require internal stop tube - refer to pages B6 and B7
Alternative rod and bore combinations available
CEP-12 -100SE
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
D9
L7
L2 + STROKE
L3 + STROKE L4
D3
D7
L12
D6 BSP.P (RAISED REAR PORT
L6 L5
L12
L15
L13
L1 + STROKE L15
L10 OVER BALL
L9 OVER HSG
L14 + STROKE
SWIVEL EYE WELDED L6 L12
L13
L15
D5
L11
D2
BSF
L11
L8
CYLINDERS MARINE & SUBSEA
SWIVEL EYE MOUNTING SERIES 12-100 WP 250 BAR
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D9
Page 16
SERIES BORE ROD D2 D3 D4 D5 D6 L1 L2 L3 L4 L5 L6 L7 L8
12 28.58 12.7 M10 35 12.7 3x5 1/8 115 126 50 46 20 13 30 28
18 31.75 18 1/2 38 13 4x6 1/4 122 135 54 48 22 13 33 30
21 50.8 25.4 3/4 60 19.1 5x6 1/2 165 181 73 66 29 17 41 45
28 63.5 31.75 1 76 25.4 5x6 1/2 175 194 75 72 38 19 48 53
Long stroke cylinders may require internal stop tube - refer to pages B6 and B7 Alternative rod and bore combinations available
CEP-12 -28RE
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
D10
L7 L3 + STROKE L4 L5 D3
D6 BSP.P L6
D4
D5
L1 + STROKE
L2 + STROKE
D2
BSF
L8
CYLINDERS MARINE & SUBSEA
REAR EYE MOUNTING
SERIES 12-28 WP 250 BAR
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D10
Page 17
Rear Eye Mounting Series 35-100 WP 250 bar
SERIES BORE ROD D2 D3 D4 D5 D6 L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 L12
35 76.2 44.45 11/4 89 25.40 6x8 3/4 222 38 83 76 51 22 63 60 38 76 38 29
38 80 56 M42x2 95 32 8x10 3/4 248 40 87 86 56 24 75 64 40 80 50 41
48 100 63.5 13/4 115 38.10 8x10 3/4 308 51 108 102 76 25 98 73 50 102 57 46
52 125 70 21/4 145 45 8x13 3/4 336 60 129 98 80 18 109 89 60 120 60 47
63 152.4 88.9 21/2 171 50.80 10x13 3/4 371 64 129 128 89 31 114 102 65 128 63 49
65 160 88.9 M64x3 180 60 10x13 1 382 70 129 128 90 31 125 113 75 140 75 57
85 200 110 3x12 230 80 16x25 1 496 80 149 165 89 28 182 138 100 160 100 79
100 250 140/160 31/2x12 278 90 – 1 638 101.5 131 288 110 50 219 162 150 203 127 102
Long stroke cylinders may require internal stop tube - refer to pages B6 and B7 Alternative rod and bore combinations available
CEP-35-100RE
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
D11
L7 L3 + STROKE L4 L5 D3
D6 BSP.P L11 L6
D4 (H8) PORT
L2 L12
D5
L9
L1 + STROKE
L10
D2
BSF
L8
CYLINDERS MARINE & SUBSEA
REAR EYE MOUNTING SERIES 35-100 WP 250 BAR
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D11
Page 18
Pad Eye Mounting Series 12-100 WP 250 bar
SERIES BORE ROD D2 D3 D4 D5 D6 D7 L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 L12 L13 L14
12 28.58 12.7 M10 35 10 3x5 1/8 19 133 181 50 89 48 13 37 28 13 26 25 13 158 20
18 31.75 18 1/2 38 12.7 4x6 1/4 25 141 191 54 99 50 13 38 30 13 26 25 13 166 20
21 50.8 25.4 3/4 60 19.05 5x6 1/2 35 191 255 73 131 64 17 51 45 19 40 32 20 223 25
28 63.5 31.75 1 76 25.4 5x6 1/2 40 204 274 75 142 70 19 57 53 26 50 38 25 242 31
35 76.2 44.45 11/4 89 25.4 6x8 3/4 45 222 298 83 152 76 22 63 60 38 76 38 38 260 29
38 80 56 M42x2 95 32 8x10 3/4 64 248 348 87 186 100 24 75 64 40 80 50 40 298 41
48 100 63.5 13/4 115 38.1 8x10 3/4 64 308 416 108 210 108 25 98 73 50 102 57 51 365 39
52 125 70 21/4 145 45 8x13 3/4 76 336 461 129 223 125 18 109 89 60 120 60 60 396 47
63 152.4 88.9 21/2 171 50.8 10x13 3/4 89 371 504 129 260 133 31 114 102 65 128 63 64 434 50
65 160 88.9 M64x3 180 60 10x13 1 89 382 527 129 273 145 31 125 113 75 140 75 70 457 58
85 200 110 3x12 230 80 16x25 1 110 496 679 149 348 183 28 182 138 100 160 100 80 596 80
100 250 140/160 31/2x12 278 90 20x25 1 125 638 860 131 462 222 50 219 162 150 203 127 101.5 765 104
Long stroke cylinders may require internal stop tube - refer to pages B6 and B7 Alternative rod and bore combinations available
CEP-12 -100PE
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
D12
7L
L2 + STROKE
L3 + STROKE 4L
D3
D7
L11
D4 (H8)
D6 BSP.P (RAISED REAR PORT
L6 L5
L11
L12
L14 L1 + STROKE
D5
L12
L14 L9
L13 + STROKE
PAD EYE WELDED 6L
L12
L14
L10
D2
BSF
L10
L10
L8
CYLINDERS MARINE & SUBSEA
PAD EYE MOUNTING SERIES 12-100 WP 250 BAR
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D12
Page 19
SERIES BORE ROD D2 D3 D4 D5 D6 L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 L12
12 28.58 12.7 M10 35 12 3x5 1/8 73 108 50 46 20 13 12 28 47 12 51 25
18 31.75 18 1/2 38 19.05 4x6 1/4 76 116 54 49 22 13 13 30 64 19 51 25
21 50.8 25.4 3/4 60 25.4 5x6 1/2 107 159 73 66 29 17 19 45 89 25 76 38
28 63.5 31.75 1 76 31.75 5x6 1/2 119 166 75 72 38 19 19 53 114 32 102 51
35 76.2 44.45 11/4 89 38.1 6x8 3/4 138 184 83 76 51 22 25 60 115 44 102 51
38 80.0 56 M42x2 95 40 8x10 3/4 150 198 87 86 56 24 25 64 120 44 127 51
L1 trunnion centre line can coincide with L4 rod port centre line Long stroke cylinders may require internal stop tube - refer to pages B6 and B7
Alternative rod and bore combinations available
CEP-12-38TN
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
D13
L7 L3 + STROKE L4 L5 L10 = L9 = L10
D6 BSP.P
L6
L1 MIN
D5
L2 + STROKE
D3
D2
BSF
D4
F8
L8
= L1
1 =
CYLINDERS MARINE & SUBSEA
TRUNNION MOUNTING
SERIES 12-38 WP 250 BAR
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D13
Page 20
Trunnion Mounting Series 48-100 WP 250 bar
SERIES BORE ROD D2 D3 D4 D5 D6 L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 L12
48 100 63.5 13/4 115 44.45 8x10 3/4 155 251 108 102 76 25 41 73 165 44 152 60
52 125 70 21/4 145 50.8 8x13 3/4 154 276 129 98 80 18 49 89 203 51 184 65
63 152.4 88.9 21/2 171 63.5 10x13 3/4 190 308 129 128 89 31 51 102 229 64 229 75
65 160 88.9 M64x3 180 70 10x13 1 210 308 129 128 90 31 50 113 250 70 250 85
85 200 110 3 x12 230 88.9 16x25 1 260 396 149 165 89 28 82 138 305 89 280 125
100 250 140/160 31/2x12 278 100 – 1 430 511 131 288 110 50 92 162 350 100 340 150
L1 trunnion centre line can coincide with L4 rod port centre line Long stroke cylinders may require internal stop tube - refer to pages B6 and B7
Alternative rod and bore combinations available
CEP-48 -100TN
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
D14
L7 L3 + STROKE L4 L5 L10 = L9 = L10
D6 BSP.P
L6
L12
L1 MIN
D5
L2 + STROKE
D3
D2
BSF
D4
F8
L8
=
L11
=
CYLINDERS MARINE & SUBSEA
TRUNNION MOUNTING SERIES 48-100 WP 250 BAR
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D14
Page 21
Front Flange Mounting Series 12-100 WP 250 bar
SERIES BORE ROD D2 D3 D4 D5 D6 D7 D8 D9 L1 L2 L3 L4 L5 L6 L7 L8 L9
12 28.58 12.7 M10 35 4x9 3x5 1/8 62 85 35 18 108 50 46 20 5 12 28 8
18 31.75 18 1/2 38 4x9 4x6 1/4 65 85 42 17 116 54 49 22 4 13 30 8
21 50.8 25.4 3/4 60 4x14 5x6 1/2 102 127 76 20 159 73 66 29 3 19 45 16
28 63.5 31.75 1 76 6x14 5x6 1/2 115 140 89 22 166 75 72 38 3 19 53 16
35 76.2 44.45 11/4 89 6x18 6x8 3/4 152 191 114 23 184 83 76 51 3 25 60 22
38 80 56 M42x2 95 6x18 10x8 3/4 160 200 120 28 198 87 86 54 4 25 64 22
48 100 63.5 13/4 115 6x21 8x10 3/4 191 235 140 30 251 108 102 76 5 41 73 22
52 125 70 21/4 145 8x23 8x13 3/4 220 270 175 23 276 129 98 80 5 49 89 22
63 152.4 88.9 21/2 171 8x27 10x13 3/4 241 305 197 35 307 129 128 89 4 50 102 25
65 160 88.9 M64x3 180 8x32 10x13 1 280 350 220 35 307 129 128 90 5 50 113 32
85 200 110 3x12 230 8x34 16x25 1 318 406 241 35 396 149 165 89 7 82 138 42
100 250 140/160 31/2x12 278 10x35 – 1 400 500 300 60 511 131 288 110 10 92 162 70
Long stroke cylinders may require internal stop tube - refer to pages B6 and B7 Alternative rod and bore combinations available
CEP-12-100FF
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
L7 L3 + STROKE L4 L5 D8
D9
D6 BSP.P (RAISED REAR PORT
D5
L6 D7
(PCD)
L9 L1 D4
L2 + STROKE
D15
D3
D2
BSF
L8
CYLINDERS MARINE & SUBSEA
FRONT FLANGE MOUNTING SERIES 12-100 WP 250 BAR
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D15
Page 22
SERIES BORE ROD D2 D3 D4 D5 D6 D7 L1 L2 L3 L4 L5 L6 L7 L8 L9
12 28.58 12.7 M10 35 4x7 3x5 1/8 60 104 22 50 46 20 13 11 28 57
18 31.75 18 1/2 38 4x7 4x6 1/4 60 108 22 48 48 22 13 11 30 57
21 50.8 25.4 3/4 60 4x11 5x6 1/2 83 149 32 67 66 29 17 16 45 76
28 63.5 31.75 1 76 4x11 5x6 1/2 102 156 32 69 72 38 19 16 53 90
35 76.2 44.45 11/4 89 4x14 6x8 3/4 124 171 38 76 76 51 22 19 60 120
Long stroke cylinders may require internal stop tube - refer to pages B6 and B7 Alternative rod and bore combinations available
CEP-12-35RF
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
L7 L3 + STROKE L4 L5
D6 BSP.P D7 (PCD)
L6 D5
L2
L1 + STROKE D4
D16
L9
SQ
UAR
E
D3
D2
BSF
L8
CYLINDERS MARINE & SUBSEA
REAR FLANGE MOUNTING
SERIES 12-35 WP 250 BAR
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D16
Page 23
Rear Flange Mounting Series 38-100 WP 250 bar
SERIES BORE ROD D2 D3 D4 D5 D6 D7 D8 L1 L2 L3 L4 L5 L6 L7 L8
38 80 56 M42x2 95 6x18 8x10 3/4 160 200 229 24 87 86 56 24 56 64
48 100 63.5 13/4 115 6x21 8x10 3/4 191 235 277 25 108 102 76 25 67 73
52 125 70 21/4 145 8x23 8x13 3/4 220 270 302 25 129 98 80 18 75 89
63 152.4 88.9 21/2 172 8x27 10x13 3/4 242 305 337 28 129 128 89 31 79 102
65 160 88.9 M64x3 180 8x32 10x13 1 280 350 344 35 129 128 90 31 86 113
85 200 110 3x12 230 8x34 16x25 1 318 406 438 45 149 165 89 28 124 138
100 250 140/160 31/2x12 278 10x35 – 1 400 500 578 70 131 288 110 50 159 162
Long stroke cylinders may require internal stop tube - refer to pages B6 and B7 Alternative rod and bore combinations available
CEP-38-100RF
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
D17
L7 L3 + STROKE L4 L5 D8
D6 BSP.P D3
L6 D5
L2
L1 + STROKE
D7 (PCD) D4
D2
BSF
L8
CYLINDERS MARINE & SUBSEA
REAR FLANGE MOUNTING SERIES 38-100 WP 250 BAR
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D17
Page 24
Foot Mounting Series 12-85 WP 250 bar
SERIES BORE ROD D2 D3 D4 D5 D6 L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 L12 L13 L14
12 28.58 12.7 M10 35 9 3x5 1/8 65 108 50 46 20 13 12 28 19 10 70 50 25 33
18 31.75 18 1/2 38 9 4x6 1/4 70 116 54 48 22 13 13 30 19 10 76 57 26 37
21 50.8 25.4 3/4 60 14 5x6 1/2 98 159 73 66 29 17 19 45 25 19 108 83 43 49
28 63.5 31.75 1 76 17 5x6 1/2 96 166 75 72 38 19 19 53 32 25 140 108 53 54
35 76.2 44.45 11/4 89 21 6x8 3/4 98 184 83 76 51 22 25 60 51 25 165 127 64 61
38 80 56 M42x2 95 25 8x10 3/4 105 198 87 86 56 24 25 64 55 30 190 140 68 65
48 100 63.5 13/4 115 27 8x10 3/4 145 252 108 102 76 25 41 73 64 32 229 172 80 75
52 125 70 21/4 145 27 8x13 3/4 149 276 129 98 80 18 49 89 90 38 267 203 100 82
63 152.4 88.9 21/2 171 30 10x13 3/4 168 308 129 128 89 31 51 102 90 38 292 229 111 95
65 160 88.9 M64x3 180 45 10x13 1 152 307 129 128 90 31 50 113 100 40 350 260 115 105
85 200 110 3x12 230 48 16x25 1 243 396 149 165 89 28 82 138 102 50 394 305 146 102
Long stroke cylinders may require internal stop tube - refer to pages B6 and B7 Alternative rod and bore combinations available
CEP-12-85FT
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
D18
7L L3 + STROKE 4L L5 D3
(RAISED REAR PORT
L6
L9 L9 D5
D4 L12
L1 + STROKE
L2 + STROKE
L14
L11
D6 BSP.P
D2
BSF
L10 L1
3
L8
CYLINDERS MARINE & SUBSEA
FOOT MOUNTING SERIES 12-85 WP 250 BAR
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D18
Page 25
Marine & Subsea Cylinders Welded Swivel Eye Mounting
PART NO. D I S D1 D2 D5 SI L LOAD kN
WSE-20 20 38 16 50 24 35 19 63 47
WSE-25 25 45 20 55 29 42 23 72.5 47
WSE-30 30 51 22 65 34 47 28 83.5 83
WSE-35 35 61 25 83 39.5 55 30 102.5 137
WSE-40 40 69 28 100 45 62 35 119 210
WSE-50 50 88 35 123 56 75 40 149.5 308
WSE-60 60 100 44 140 66.5 90 50 170 400
WSE-70 70 115 49 164 77.5 105 55 197 487
WSE-80 80 141 55 180 89 120 60 231 546
WSE-90 90 150 60 226 98 130 65 263 938
WSE-100 100 170 70 250 110 150 70 295 1050
WSE-110 110 185 70 295 121 160 80 322.5 1512
WSE-120 120 210 85 360 136 180 90 390 2275
Optional swivel eye mountings: ±6º angular movement Steel on steel sliding contact with lubricator
CEP-AWSE
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
D19
S1
D1
PIN NOT SUPPLIED
I
L
D5
D2
D
CYLINDERS MARINE & SUBSEA
WELDED SWIVEL EYE MOUNTING
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D19
Page 26
Alternative Rod Mounting Screwed Swivel Eye
PART NO. D I S LF D1 D2 D3 D4 D5 SI S2 L L1 F LOAD kN
SSE-20 20 50 16 17 56 46 25 24 35 19 17 80 25 M16X1.5 47
SSE-25 25 50 20 17 56 46 25 29 42 23 21 80 25 M16X1.5 47
SSE-30 30 60 22 23 64 50 32 34 47 28 26 94 30 M22X1.5 70
SSE-35 35 70 25 29 78 66 40 39.5 55 30 28 112 38 M28X1.5 100
SSE-40 40 85 28 36 94 76 49 45 62 35 33 135 45 M35X1.5 160
SSE-50 50 105 35 46 116 90 61 56 75 40 37 165 55 M45X1.5 240
SSE-60 60 130 44 59 130 120 75 66.5 90 50 46 200 65 M58X1.5 270
SSE-70 70 150 49 66 154 130 86 77.5 105 55 51 232 75 M65X1.5 310
SSE-80 80 170 55 81 176 160 102 89 120 60 55 265 80 M80X2.0 400
SSE-90 90 210 60 101 206 180 124 98 130 65 60 323 90 M100X2 570
SSE-100 100 235 70 111 230 200 138 110 150 70 65 360 105 M110X2 680
SSE-110 110 265 70 125 265 220 152 121 160 80 74 408 115 M120X3 1000
SSE-120 120 310 85 135 340 257 172 136 180 90 84 490 140 M130X3 1800
Optional swivel eye mountings: ±6º angular movement Steel on steel sliding contact with lubricator
CEP-ASSE
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
D20
D1
D2
D3
PIN NOT SUPPLIED
S2
I
L
D5
D4
D
LF
L1
CYLINDERS MARINE & SUBSEA
ALTERNATIVE ROD MOUNTING
SCREWED SWIVEL EYE
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D20
Page 27
H
ØG(H8) D CLEVIS SCREWED
(PIN & CLIPS SUPPLIED)
ØH
B ØG(H8)
WELD CLEARANCE
ROD SHOULDER
PAD EYE SCREWED
(PIN NOT SUPPLIED)
ØG(H8)
WELD CLEARANCE
ROD SHOULDER
PAD EYE WELDED
(PIN NOT SUPPLIED)
Rod End Mountings
SERIES A B C D E F G H 12 M10
X 1.5 40 52 10 20 20 10 20
18 1/2 56 72 13 28 25 13 25 21 3/4 80 105 19 40 40 19 40 28 1 100 132 26 50 50 26 50 35 11/4 100 132 26 50 50 26 50 38 M36x2 144 188 35 72 70 35 70
SERIES A B C D E F G H J 12 M10
X 1.5 48 61 13 25 26 12.7 19 20
18 1/2 50 63 13 25 26 12.7 25 20
21 3/4 64 84 19 32 40 19.05 35 25
28 1 70 95 26 38 50 25.4 40 31
35 11/4 76 114 38 38 76 25.4 45 29
38 13/4 100 140 40 50 80 32 64 41
48 13/4 108 159 50 57 102 38.1 64 39
52 21/4 125 185 60 60 120 45 76 47
63 21/2 133 197 65 63 128 50.8 89 50
65 21/2 145 215 75 75 140 60 90 58
85 3x12 183 263 100 100 160 80 110 80
100 31/2x12 222 324 150 127 203 90 125 104
SERIES A B C D E F G H J
12 – – 38 13 25 26 12.7 – 20
18 – – 38 13 25 26 12.7 – 20
21 – – 52 19 32 40 19.05 – 25
28 – – 63 26 38 50 25.4 – 31
35 – – 76 38 38 76 25.4 – 29
38 – – 90 40 50 80 32 – 41
48 – – 108 50 57 102 38.1 – 39
52 – – 120 60 60 120 45 – 47
63 – – 127 65 63 128 50.8 – 50
65 – – 145 75 75 140 60 – 58
85 – – 180 100 100 160 80 – 80
100 – – 229 150 127 203 90 – 104
CEP-RDM
Subsea and industrial hydraulic manufacturers
Hillington Park Glasgow G52 4PQ Scotland Tel: 0141 810 4511 Fax: 0141 883 3825
Email: [email protected] Internet: www.aph.co.uk
Represented in USA by: Air Power Hydraulics Inc 87 Amlajack Way Newnan GA 30265 Tel: 770 683 7221 Fax: 770 683 7242 E: [email protected] Web: www.aphusa.com
D21
A
BSF
A
BSF
F
F
F
CYLINDERS MARINE & SUBSEA
ROD END MOUNTINGS
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D21
Page 28
Ordering Code
Example
CEPAC
100 SS 2000 150 FF 19T
ROD MOUNTING
BORE mm
*28.58
32
*50.8
*63.5
*76.2
80
100
ROD DIA mm
*12.7
18
*25.4
*31.75
*44.5
56
*63.5
SERIES
12
18
21
28
35
38
48
19T
19E
19S
19C
19EW
19SW
WSE
SSE
Threaded
Pad Eye Screwed
Swivel Eye Screwed
Clevis Screwed
Pad Eye Welded
Swivel Eye Welded
Alternative Welded Swivel Eye
Alternative Screwed Swivel Eye
125
*152.4
70 52
*88.9 63
BODY MOUNTING
* Imperial Size
APPLICATION
TN
FF
RF
FT
WSE
Trunnion
Front Flange
Rear Flange
Foot
Alternative Welded Swivel Eye
Surface Marine SM
Subsea SS
Stop Tube in mm - Refer to pages B6 and B7
Stroke in mm
Optional extras
1. Phosphor bronze self-aligning eyes
2. Through-rod design
3. Rod-to-bore ratios other than specified
4. Special purpose telescopic design
5. Load-holding and control valves
integrally-mounted
6. Internal electronic rod position indication
7. Fixed cushioning
160 *88.9 65 SE Swivel Eye
200 110 85 RE Rear Eye
250 140/160 100 PE Pad Eye
CYLINDERS MARINE & SUBSEA
ORDERING CODE
Hillington Park, Glasgow, G52 4PQ, Scotland Tel: 0141 810 4511 - Fax: 0141 883 3825
Email: [email protected] - Website: www.aph.co.uk
D22