BSEN 10025 : 2000 New (Edition)
Eltel Middle East, Syria BSEN 10025 : 2000 (New Edition)
A) General Information
SelectSpecificationDesignationSteel NumberProduct FormAlloy GroupTitleNotesICS NumberStatus
EN 10025-1:2004------bar, rod, plate, sheet, strip, shape---Hot Rolled Products of Structural Steels - Part 1: General Technical Delivery Conditionsdetails77.140.10, 77.140.50 Current
EN 10025-2:2004S1851.0035bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-2:2004S235JR1.0038bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-2:2004S275JR1.0044bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-2:2004S355JR1.0045bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-2:2004E2951.0050bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-2:2004E3351.0060bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-2:2004E3601.0070bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-2:2004S235J01.0114bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-2:2004S235J21.0117bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-2:2004S275J01.0143bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-2:2004S275J21.0145bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
SelectSpecificationDesignationSteel NumberProduct FormAlloy GroupTitleNotesICS NumberStatus
EN 10025-2:2004S355J01.0553bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-2:2004S355J21.0577bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-2:2004S450J01.0590bar, rod, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-2:2004S355K21.0596bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels---77.140.10, 77.140.45, 77.140.50 Current
EN 10025-3:2004S275N1.0490bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 3: Technical Delivery Conditions for Normalized/Normalized Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-3:2004S275NL1.0491bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 3: Technical Delivery Conditions for Normalized/Normalized Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-3:2004S355N1.0545bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 3: Technical Delivery Conditions for Normalized/Normalized Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-3:2004S355NL1.0546bar, rod, plate, sheet, strip, shapecarbon steelHot Rolled Products of Structural Steels - Part 3: Technical Delivery Conditions for Normalized/Normalized Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-3:2004S460N1.8901bar, rod, plate, sheet, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 3: Technical Delivery Conditions for Normalized/Normalized Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-3:2004S420N1.8902bar, rod, plate, sheet, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 3: Technical Delivery Conditions for Normalized/Normalized Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-3:2004S460NL1.8903bar, rod, plate, sheet, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 3: Technical Delivery Conditions for Normalized/Normalized Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-3:2004S420NL1.8912bar, rod, plate, sheet, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 3: Technical Delivery Conditions for Normalized/Normalized Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-4:2004S275M1.8818bar, rod, plate, sheet, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 4: Technical Delivery Conditions for Thermomechanical Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
B) Chemical Composition
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)CMnPSSiCrNiMoVAlCuTiNbNNotes
EN 10025-2:2004S1851.0035t 250------------------------------------------details
EN 10025-2:2004S235JR1.0038t 400.17 max.1.40 max.0.035 max.0.035 max.------------------0.55 max.------0.012 max.details
EN 10025-2:2004S235JR1.003840 < t 1500.20 max.1.40 max.0.035 max.0.035 max.------------------0.55 max.------0.012 max.details
EN 10025-2:2004S235JR1.0038150 < t 2500.20 max.1.40 max.0.035 max.0.035 max.------------------0.55 max.------0.012 max.details
EN 10025-2:2004S275JR1.0044t 400.21 max.1.50 max.0.035 max.0.035 max.------------------0.55 max.------0.012 max.details
EN 10025-2:2004S275JR1.004440 < t 1500.22 max.1.50 max.0.035 max.0.035 max.------------------0.55 max.------0.012 max.details
EN 10025-2:2004S275JR1.0044150 < t 2500.22 max.1.50 max.0.035 max.0.035 max.------------------0.55 max.------0.012 max.details
EN 10025-2:2004S355JR1.0045t 300.24 max.1.60 max.0.035 max.0.035 max.0.55 max.---------------0.55 max.------0.012 max.details
EN 10025-2:2004S355JR1.004530 < t 1500.24 max.1.60 max.0.035 max.0.035 max.0.55 max.---------------0.55 max.------0.012 max.details
EN 10025-2:2004S355JR1.0045150 < t 2500.24 max.1.60 max.0.035 max.0.035 max.0.55 max.---------------0.55 max.------0.012 max.details
EN 10025-2:2004E2951.0050t 250------0.045 max.0.045 max.---------------------------0.012 max.details
EN 10025-2:2004E3351.0060t 250------0.045 max.0.045 max.---------------------------0.012 max.details
EN 10025-2:2004E3601.0070t 250------0.045 max.0.045 max.---------------------------0.012 max.details
EN 10025-2:2004S235J01.0114t 400.17 max.1.40 max.0.030 max.0.030 max.------------------0.55 max.------0.012 max.details
EN 10025-2:2004S235J01.011440 < t 1500.17 max.1.40 max.0.030 max.0.030 max.------------------0.55 max.------0.012 max.details
EN 10025-2:2004S235J01.0114150 < t 2500.17 max.1.40 max.0.030 max.0.030 max.------------------0.55 max.------0.012 max.details
EN 10025-2:2004S235J21.0117t 400.17 max.1.40 max.0.025 max.0.025 max.------------------0.55 max.---------details
EN 10025-2:2004S235J21.011740 < t 1500.17 max.1.40 max.0.025 max.0.025 max.------------------0.55 max.---------details
EN 10025-2:2004S235J21.0117150 < t 2500.17 max.1.40 max.0.025 max.0.025 max.------------------0.55 max.---------details
EN 10025-2:2004S235J21.0117250 < t 4000.17 max.1.40 max.0.025 max.0.025 max.------------------0.55 max.---------details
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)CMnPSSiCrNiMoVAlCuTiNbNNotes
EN 10025-2:2004S275J01.0143t 400.18 max.1.50 max.0.030 max.0.030 max.------------------0.55 max.------0.012 max.details
EN 10025-2:2004S275J01.014340 < t 1500.18 max.1.50 max.0.030 max.0.030 max.------------------0.55 max.------0.012 max.details
EN 10025-2:2004S275J01.0143150 < t 2500.18 max.1.50 max.0.030 max.0.030 max.------------------0.55 max.------0.012 max.details
EN 10025-2:2004S275J21.0145t 400.18 max.1.50 max.0.025 max.0.025 max.------------------0.55 max.---------details
EN 10025-2:2004S275J21.014540 < t 1500.18 max.1.50 max.0.025 max.0.025 max.------------------0.55 max.---------details
EN 10025-2:2004S275J21.0145150 < t 2500.18 max.1.50 max.0.025 max.0.025 max.------------------0.55 max.---------details
EN 10025-2:2004S355J01.0553t 300.20 max.1.60 max.0.030 max.0.030 max.0.55 max.---------------0.55 max.------0.012 max.details
EN 10025-2:2004S355J01.055330 < t 400.20 max.1.60 max.0.030 max.0.030 max.0.55 max.---------------0.55 max.------0.012 max.details
EN 10025-2:2004S355J01.055340 < t 1500.22 max.1.60 max.0.030 max.0.030 max.0.55 max.---------------0.55 max.------0.012 max.details
EN 10025-2:2004S355J01.0553150 < t 2500.22 max.1.60 max.0.030 max.0.030 max.0.55 max.---------------0.55 max.------0.012 max.details
EN 10025-2:2004S355J21.0577t 300.20 max.1.60 max.0.025 max.0.025 max.0.55 max.---------------0.55 max.---------details
EN 10025-2:2004S355J21.057730 < t 400.20 max.1.60 max.0.025 max.0.025 max.0.55 max.---------------0.55 max.---------details
EN 10025-2:2004S355J21.057740 < t 1500.22 max.1.60 max.0.025 max.0.025 max.0.55 max.---------------0.55 max.---------details
EN 10025-2:2004S355J21.0577150 < t 2500.22 max.1.60 max.0.025 max.0.025 max.0.55 max.---------------0.55 max.---------details
EN 10025-2:2004S355J21.0577250 < t 4000.22 max.1.60 max.0.025 max.0.025 max.0.55 max.---------------0.55 max.---------details
EN 10025-2:2004S450J01.05903 t 400.20 max.1.70 max.0.030 max.0.030 max.0.55 max.---------------0.55 max.------0.025 max.details
EN 10025-2:2004S450J01.059040 < t 1500.22 max.1.70 max.0.030 max.0.030 max.0.55 max.---------------0.55 max.------0.025 max.details
EN 10025-2:2004S355K21.0596t 300.20 max.1.60 max.0.025 max.0.025 max.0.55 max.---------------0.55 max.---------details
EN 10025-2:2004S355K21.059630 < t 400.20 max.1.60 max.0.025 max.0.025 max.0.55 max.---------------0.55 max.---------details
EN 10025-2:2004S355K21.059640 < t 1500.22 max.1.60 max.0.025 max.0.025 max.0.55 max.---------------0.55 max.---------details
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)CMnPSSiCrNiMoVAlCuTiNbNNotes
EN 10025-2:2004S355K21.0596150 < t 2500.22 max.1.60 max.0.025 max.0.025 max.0.55 max.---------------0.55 max.---------details
EN 10025-2:2004S355K21.0596250 < t 4000.22 max.1.60 max.0.025 max.0.025 max.0.55 max.---------------0.55 max.---------details
EN 10025-3:2004S275N1.0490t 630.18 max.0.50 - 1.500.030 max.0.025 max.0.40 max.0.30 max.0.30 max.0.10 max.0.05 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.details
EN 10025-3:2004S275N1.049063 < t 2500.18 max.0.50 - 1.500.030 max.0.025 max.0.40 max.0.30 max.0.30 max.0.10 max.0.05 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.details
EN 10025-3:2004S275NL1.0491t 630.16 max.0.50 - 1.500.025 max.0.020 max.0.40 max.0.30 max.0.30 max.0.10 max.0.05 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.details
EN 10025-3:2004S275NL1.049163 < t 2500.16 max.0.50 - 1.500.025 max.0.020 max.0.40 max.0.30 max.0.30 max.0.10 max.0.05 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.details
EN 10025-3:2004S355N1.0545t 630.20 max.0.90 - 1.650.030 max.0.025 max.0.50 max.0.30 max.0.50 max.0.10 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.details
EN 10025-3:2004S355N1.054563 < t 2500.20 max.0.90 - 1.650.030 max.0.025 max.0.50 max.0.30 max.0.50 max.0.10 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.details
EN 10025-3:2004S355NL1.0546t 630.18 max.0.90 - 1.650.025 max.0.020 max.0.50 max.0.30 max.0.50 max.0.10 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.details
EN 10025-3:2004S355NL1.054663 < t 2500.18 max.0.90 - 1.650.025 max.0.020 max.0.50 max.0.30 max.0.50 max.0.10 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.details
EN 10025-3:2004S460N1.8901t 630.20 max.1.00 - 1.700.030 max.0.025 max.0.60 max.0.30 max.0.80 max.0.10 max.0.20 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.details
EN 10025-3:2004S460N1.890163 < t 1000.20 max.1.00 - 1.700.030 max.0.025 max.0.60 max.0.30 max.0.80 max.0.10 max.0.20 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.details
EN 10025-3:2004S460N1.8901100 < t 2500.20 max.1.00 - 1.700.030 max.0.025 max.0.60 max.0.30 max.0.80 max.0.10 max.0.20 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.details
EN 10025-3:2004S420N1.8902t 630.20 max.1.00 - 1.700.030 max.0.025 max.0.60 max.0.30 max.0.80 max.0.10 max.0.20 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.details
EN 10025-3:2004S420N1.890263 < t 1000.20 max.1.00 - 1.700.030 max.0.025 max.0.60 max.0.30 max.0.80 max.0.10 max.0.20 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.details
EN 10025-3:2004S420N1.8902100 < t 2500.20 max.1.00 - 1.700.030 max.0.025 max.0.60 max.0.30 max.0.80 max.0.10 max.0.20 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.details
EN 10025-3:2004S460NL1.8903t 630.20 max.1.00 - 1.700.025 max.0.020 max.0.60 max.0.30 max.0.80 max.0.10 max.0.20 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.details
EN 10025-3:2004S460NL1.890363 < t 1000.20 max.1.00 - 1.700.025 max.0.020 max.0.60 max.0.30 max.0.80 max.0.10 max.0.20 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.details
EN 10025-3:2004S460NL1.8903100 < t 2500.20 max.1.00 - 1.700.025 max.0.020 max.0.60 max.0.30 max.0.80 max.0.10 max.0.20 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.details
EN 10025-3:2004S420NL1.8912t 630.20 max.1.00 - 1.700.025 max.0.020 max.0.60 max.0.30 max.0.80 max.0.10 max.0.20 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.details
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)CMnPSSiCrNiMoVAlCuTiNbNNotes
EN 10025-3:2004S420NL1.891263 < t 1000.20 max.1.00 - 1.700.025 max.0.020 max.0.60 max.0.30 max.0.80 max.0.10 max.0.20 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.details
EN 10025-3:2004S420NL1.8912100 < t 2500.20 max.1.00 - 1.700.025 max.0.020 max.0.60 max.0.30 max.0.80 max.0.10 max.0.20 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.details
EN 10025-4:2004S275M1.8818t 400.13 max.1.50 max.0.030 max.0.025 max.0.50 max.0.30 max.0.30 max.0.10 max.0.08 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.details
EN 10025-4:2004S275M1.881840 < t 630.13 max.1.50 max.0.030 max.0.025 max.0.50 max.0.30 max.0.30 max.0.10 max.0.08 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.details
EN 10025-4:2004S275M1.881863 < t 1500.13 max.1.50 max.0.030 max.0.025 max.0.50 max.0.30 max.0.30 max.0.10 max.0.08 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.details
E) Carbon Equivalent
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Carbon EquivalenceNotes
EN 10025-2:2004S1851.0035t 250------
EN 10025-2:2004S235JR1.0038t 40CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.35 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
EN 10025-2:2004S235JR1.003840 < t 150CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.38 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
EN 10025-2:2004S235JR1.0038150 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.40 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Carbon EquivalenceNotes
EN 10025-2:2004S275JR1.0044t 40CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.40 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S275JR1.004440 < t 150CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.42 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S275JR1.0044150 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.44 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S355JR1.0045t 30CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.45 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Carbon EquivalenceNotes
EN 10025-2:2004S355JR1.004530 < t 150CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.47 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S355JR1.0045150 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.49 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
For long products a maximum CE of 0.54 applies.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004E2951.0050t 250------
EN 10025-2:2004E3351.0060t 250------
EN 10025-2:2004E3601.0070t 250------
EN 10025-2:2004S235J01.0114t 40CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.35 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
EN 10025-2:2004S235J01.011440 < t 150CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.38 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Carbon EquivalenceNotes
EN 10025-2:2004S235J01.0114150 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.40 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
EN 10025-2:2004S235J21.0117t 40CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.35 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
EN 10025-2:2004S235J21.011740 < t 150CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.38 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
EN 10025-2:2004S235J21.0117150 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.40 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
EN 10025-2:2004S235J21.0117250 < t 400CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.40 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
EN 10025-2:2004S275J01.0143t 40CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.40 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S275J01.014340 < t 150CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.42 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S275J01.0143150 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.44 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S275J21.0145t 40CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.40 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S275J21.014540 < t 150CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.42 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Carbon EquivalenceNotes
EN 10025-2:2004S275J21.0145150 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.44 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S355J01.0553t 30CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.45 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S355J01.055330 < t 40CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.47 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Carbon EquivalenceNotes
EN 10025-2:2004S355J01.055340 < t 150CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.47 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S355J01.0553150 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.49 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
For long products a maximum CE of 0.54 applies.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S355J21.0577t 30CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.45 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Carbon EquivalenceNotes
EN 10025-2:2004S355J21.057730 < t 40CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.47 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S355J21.057740 < t 150CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.47 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S355J21.0577150 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.49 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
For long products a maximum CE of 0.54 applies.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S355J21.0577250 < t 400CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.49 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Carbon EquivalenceNotes
EN 10025-2:2004S450J01.05903 t 40CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE applicable to long products only. CE 0.47 max.
EN 10025-2:2004S450J01.059040 < t 150CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE applicable to long products only. CE 0.49 max.
EN 10025-2:2004S355K21.0596t 30CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.45 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S355K21.059630 < t 40CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.47 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Carbon EquivalenceNotes
EN 10025-2:2004S355K21.059640 < t 150CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.47 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S355K21.0596150 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.49 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
For long products a maximum CE of 0.54 applies.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-2:2004S355K21.0596250 < t 400CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15CE 0.49 max.
Copper-content between 0.25% and 0.40% on ladle analysis and between 0.20% and 0.45% on product analysis can be agreed at the time of order. In this case the maximum carbon equivalent shall be increased by 0.02%.
When supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
EN 10025-3:2004S275N1.0490t 63CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.40 max.
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Carbon EquivalenceNotes
EN 10025-3:2004S275N1.049063 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.42 max.
EN 10025-3:2004S275NL1.0491t 63CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.40 max.
EN 10025-3:2004S275NL1.049163 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.42 max.
EN 10025-3:2004S355N1.0545t 63CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.43 max.
EN 10025-3:2004S355N1.054563 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.45 max.
EN 10025-3:2004S355NL1.0546t 63CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.43 max.
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Carbon EquivalenceNotes
EN 10025-3:2004S355NL1.054663 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.45 max.
EN 10025-3:2004S460N1.8901t 63CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.53 max.
EN 10025-3:2004S460N1.890163 < t 100CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.54 max.
EN 10025-3:2004S460N1.8901100 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.55 max.
EN 10025-3:2004S420N1.8902t 63CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.48 max.
EN 10025-3:2004S420N1.890263 < t 100CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.50 max.
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Carbon EquivalenceNotes
EN 10025-3:2004S420N1.8902100 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.52 max.
EN 10025-3:2004S460NL1.8903t 63CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.53 max.
EN 10025-3:2004S460NL1.890363 < t 100CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.54 max.
EN 10025-3:2004S460NL1.8903100 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.55 max.
EN 10025-3:2004S420NL1.8912t 63CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.48 max.
EN 10025-3:2004S420NL1.891263 < t 100CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.50 max.
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Carbon EquivalenceNotes
EN 10025-3:2004S420NL1.8912100 < t 250CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.52 max.
EN 10025-4:2004S275M1.8818t 40CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.34 max.
EN 10025-4:2004S275M1.881840 < t 63CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.35 max.
EN 10025-4:2004S275M1.881863 < t 150CE=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15When products are supplied with a control on Si, the maximum carbon equivalent shall be increased as follows:S0.030%; increase CE by 0.02%Si0.25% increase CE by 0.01%
CE 0.38 max.
For thicknesses 120 < t 150mm the CE only applies for long products.
C) Mechanical Properties
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Yield Strength (MPa)Tensile Strength (MPa)% ElongationGrain SizeHeat TreatmentNotes
EN 10025-2:2004S1851.0035t < 3185 min.310 - 540------as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S1851.00353 t 16185 min.290 - 51018 min. (L)16 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S1851.003516 < t 40175 min.290 - 51018 min. (L)16 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S1851.003540 < t 63175 min.290 - 51017 min. (L)15 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S1851.003563 < t 80175 min.290 - 51016 min. (L)14 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S1851.003580 < t 100175 min.290 - 51016 min. (L)14 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Yield Strength (MPa)Tensile Strength (MPa)% ElongationGrain SizeHeat TreatmentNotes
EN 10025-2:2004S1851.0035100 < t 150165 min.280 - 50015 min. (L)13 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S1851.0035150 < t 200155 min.270 - 49015 min. (L)13 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S1851.0035200 < t 250145 min.270 - 49015 min. (L)13 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235JR1.0038t < 3235 min.360 - 510------as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235JR1.00383 t 16235 min.360 - 51026 min. (L)24 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235JR1.003816 < t 40225 min.360 - 51026 min. (L)24 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235JR1.003840 < t 63215 min.360 - 51025 min. (L)24 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235JR1.003863 < t 80215 min.360 - 51024 min. (L)22 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235JR1.003880 < t 100215 min.360 - 51024 min. (L)22 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235JR1.0038100 < t 150195 min.350 - 50022 min. (L)22 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235JR1.0038150 < t 200185 min.340 - 49021 min. (L)21 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235JR1.0038200 < t 250175 min.340 - 49021 min. (L)21 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275JR1.0044t < 3275 min.430 - 580------as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275JR1.00443 t 16275 min.410 - 56023 min. (L)21 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275JR1.004416 < t 40265 min.410 - 56023 min. (L)21 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275JR1.004440 < t 63255 min.410 - 56022 min. (L)20 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275JR1.004463 < t 80245 min.410 - 56021 min. (L)19 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275JR1.004480 < t 100235 min.410 - 56021 min. (L)19 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275JR1.0044100 < t 150225 min.400 - 54019 min. (L)19 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275JR1.0044150 < t 200215 min.380 - 54018 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275JR1.0044200 < t 250205 min.380 - 54018 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Yield Strength (MPa)Tensile Strength (MPa)% ElongationGrain SizeHeat TreatmentNotes
EN 10025-2:2004S355JR1.0045t < 3355 min.510 - 680------as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355JR1.00453 t 16355 min.470 - 63022 min. (L)20 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355JR1.004516 < t 40345 min.470 - 63022 min. (L)20 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355JR1.004540 < t 63335 min.470 - 63021 min. (L)19 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355JR1.004563 < t 80325 min.470 - 63020 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355JR1.004580 < t 100315 min.470 - 63020 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355JR1.0045100 < t 150295 min.450 - 60018 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355JR1.0045150 < t 200285 min.450 - 60017 min. (L)17 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355JR1.0045200 < t 250275 min.450 - 60017 min. (L)17 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E2951.0050t < 3295 min.490 - 660------as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E2951.00503 t 16295 min.470 - 61020 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E2951.005016 < t 40285 min.470 - 61020 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E2951.005040 < t 63275 min.470 - 61019 min. (L)17 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E2951.005063 < t 80265 min.470 - 61018 min. (L)16 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E2951.005080 < t 100255 min.470 - 61018 min. (L)16 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E2951.0050100 < t 150245 min.450 - 61016 min. (L)15 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E2951.0050150 < t 200235 min.440 - 61015 min. (L)14 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E2951.0050200 < t 250225 min.440 - 61015 min. (L)14 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3351.0060t < 3335 min.590 - 770------as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3351.00603 t 16335 min.570 - 71016 min. (L)14 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3351.006016 < t 40325 min.570 - 71016 min. (L)14 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Yield Strength (MPa)Tensile Strength (MPa)% ElongationGrain SizeHeat TreatmentNotes
EN 10025-2:2004E3351.006040 < t 63315 min.570 - 71015 min. (L)13 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3351.006063 < t 80305 min.570 - 71014 min. (L)12 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3351.006080 < t 100295 min.570 - 71014 min. (L)12 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3351.0060100 < t 150275 min.550 - 71012 min. (L)11 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3351.0060150 < t 200265 min.540 - 71011 min. (L)10 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3351.0060200 < t 250255 min.540 - 71011 min. (L)10 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3601.0070t < 3360 min.690 - 900------as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3601.00703 t 16360 min.670 - 83011 min. (L)10 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3601.007016 < t 40355 min.670 - 83011 min. (L)10 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3601.007040 < t 63345 min.670 - 83010 min. (L)9 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3601.007063 < t 80335 min.670 - 8309 min. (L)8 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3601.007080 < t 100325 min.670 - 8309 min. (L)8 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3601.0070100 < t 150305 min.650 - 8308 min. (L)7 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3601.0070150 < t 200295 min.640 - 8307 min. (L)6 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004E3601.0070200 < t 250285 min.640 - 8307 min. (L)6 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J01.0114t < 3235 min.360 - 510------as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J01.01143 t 16235 min.360 - 51026 min. (L)24 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J01.011416 < t 40225 min.360 - 51026 min. (L)24 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J01.011440 < t 63215 min.360 - 51025 min. (L)24 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J01.011463 < t 80215 min.360 - 51024 min. (L)22 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J01.011480 < t 100215 min.360 - 51024 min. (L)22 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Yield Strength (MPa)Tensile Strength (MPa)% ElongationGrain SizeHeat TreatmentNotes
EN 10025-2:2004S235J01.0114100 < t 150195 min.350 - 50022 min. (L)22 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J01.0114150 < t 200185 min.340 - 49021 min. (L)21 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J01.0114200 < t 250175 min.340 - 49021 min. (L)21 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J21.0117t < 3235 min.360 - 510---6 min.as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J21.01173 t 16235 min.360 - 51026 min. (L)24 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J21.011716 < t 40225 min.360 - 51026 min. (L)24 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J21.011740 < t 63215 min.360 - 51025 min. (L)24 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J21.011763 < t 80215 min.360 - 51024 min. (L)22 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J21.011780 < t 100215 min.360 - 51024 min. (L)22 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J21.0117100 < t 150195 min.350 - 50022 min. (L)22 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J21.0117150 < t 200185 min.340 - 49021 min. (L)21 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J21.0117200 < t 250175 min.340 - 49021 min. (L)21 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S235J21.0117250 < t 400165 min.330 - 48021 min. (L)21 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J01.0143t < 3275 min.430 - 580------as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J01.01433 t 16275 min.410 - 56023 min. (L)21 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J01.014316 < t 40265 min.410 - 56023 min. (L)21 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J01.014340 < t 63255 min.410 - 56022 min. (L)20 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J01.014363 < t 80245 min.410 - 56021 min. (L)19 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J01.014380 < t 100235 min.410 - 56021 min. (L)19 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J01.0143100 < t 150225 min.400 - 54019 min. (L)19 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J01.0143150 < t 200215 min.380 - 54018 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Yield Strength (MPa)Tensile Strength (MPa)% ElongationGrain SizeHeat TreatmentNotes
EN 10025-2:2004S275J01.0143200 < t 250205 min.380 - 54018 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J21.0145t < 3275 min.430 - 580---6 min.as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J21.01453 t 16275 min.410 - 56023 min. (L)21 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J21.014516 < t 40265 min.410 - 56023 min. (L)21 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J21.014540 < t 63255 min.410 - 56022 min. (L)20 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J21.014563 < t 80245 min.410 - 56021 min. (L)19 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J21.014580 < t 100235 min.410 - 56021 min. (L)19 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J21.0145100 < t 150225 min.400 - 54019 min. (L)19 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J21.0145150 < t 200215 min.380 - 54018 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J21.0145200 < t 250205 min.380 - 54018 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S275J21.0145250 < t 400195 min.380 - 54018 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J01.0553t < 3355 min.510 - 680------as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J01.05533 t 16355 min.470 - 63022 min. (L)20 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J01.055316 < t 40345 min.470 - 63022 min. (L)20 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J01.055340 < t 63335 min.470 - 63021 min. (L)19 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J01.055363 < t 80325 min.470 - 63020 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J01.055380 < t 100315 min.470 - 63020 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J01.0553100 < t 150295 min.450 - 60018 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J01.0553150 < t 200285 min.450 - 60017 min. (L)17 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J01.0553200 < t 250275 min.450 - 60017 min. (L)17 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J21.0577t < 3355 min.510 - 680---6 min.as-rolled, normalized rolled, or thermomechanically rolleddetails
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Yield Strength (MPa)Tensile Strength (MPa)% ElongationGrain SizeHeat TreatmentNotes
EN 10025-2:2004S355J21.05773 t 16355 min.470 - 63022 min. (L)20 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J21.057716 < t 40345 min.470 - 63022 min. (L)20 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J21.057740 < t 63335 min.470 - 63021 min. (L)19 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J21.057763 < t 80325 min.470 - 63020 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J21.057780 < t 100315 min.470 - 63020 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J21.0577100 < t 150295 min.450 - 60018 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J21.0577150 < t 200285 min.450 - 60017 min. (L)17 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J21.0577200 < t 250275 min.450 - 60017 min. (L)17 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355J21.0577250 < t 400265 min.450 - 60017 min. (L)17 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S450J01.05903 t 16450 min.550 - 72017 min. (L)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S450J01.059016 < t 40430 min.550 - 72017 min. (L)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S450J01.059040 < t 63410 min.550 - 72017 min. (L)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S450J01.059063 < t 80390 min.550 - 72017 min. (L)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S450J01.059080 < t 100380 min.550 - 72017 min. (L)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S450J01.0590100 < t 150380 min.530 - 70017 min. (L)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355K21.0596t < 3355 min.510 - 680---6 min.as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355K21.05963 t 16355 min.470 - 63022 min. (L)20 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355K21.059616 < t 40345 min.470 - 63022 min. (L)20 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355K21.059640 < t 63335 min.470 - 63021 min. (L)19 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355K21.059663 < t 80325 min.470 - 63020 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355K21.059680 < t 100315 min.470 - 63020 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Yield Strength (MPa)Tensile Strength (MPa)% ElongationGrain SizeHeat TreatmentNotes
EN 10025-2:2004S355K21.0596100 < t 150295 min.450 - 60018 min. (L)18 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355K21.0596150 < t 200285 min.450 - 60017 min. (L)17 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355K21.0596200 < t 250275 min.450 - 60017 min. (L)17 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-2:2004S355K21.0596250 < t 400265 min.450 - 60017 min. (L)17 min. (T)---as-rolled, normalized rolled, or thermomechanically rolleddetails
EN 10025-3:2004S275N1.0490t 16275 min.370 - 51024 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275N1.049016 < t 40265 min.370 - 51024 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275N1.049040 < t 63255 min.370 - 51024 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275N1.049063 < t 80245 min.370 - 51023 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275N1.049080 < t 100235 min.370 - 51023 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275N1.0490100 < t 150225 min.350 - 48023 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275N1.0490150 < t 200215 min.350 - 48023 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275N1.0490200 < t 250205 min.350 - 48023 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275NL1.0491t 16275 min.370 - 51024 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275NL1.049116 < t 40265 min.370 - 51024 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275NL1.049140 < t 63255 min.370 - 51024 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275NL1.049163 < t 80245 min.370 - 51023 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275NL1.049180 < t 100235 min.370 - 51023 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275NL1.0491100 < t 150225 min.350 - 48023 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275NL1.0491150 < t 200215 min.350 - 48023 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S275NL1.0491200 < t 250205 min.350 - 48023 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355N1.0545t 16355 min.470 - 63022 min.6 min.normalized or normalized rolleddetails
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Yield Strength (MPa)Tensile Strength (MPa)% ElongationGrain SizeHeat TreatmentNotes
EN 10025-3:2004S355N1.054516 < t 40345 min.470 - 63022 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355N1.054540 < t 63335 min.470 - 63022 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355N1.054563 < t 80325 min.470 - 63021 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355N1.054580 < t 100315 min.470 - 63021 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355N1.0545100 < t 150295 min.450 - 60021 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355N1.0545150 < t 200285 min.450 - 60021 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355N1.0545200 < t 250275 min.450 - 60021 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355NL1.0546t 16355 min.470 - 63022 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355NL1.054616 < t 40345 min.470 - 63022 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355NL1.054640 < t 63335 min.470 - 63022 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355NL1.054663 < t 80325 min.470 - 63021 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355NL1.054680 < t 100315 min.470 - 63021 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355NL1.0546100 < t 150295 min.450 - 60021 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355NL1.0546150 < t 200285 min.450 - 60021 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S355NL1.0546200 < t 250275 min.450 - 60021 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S460N1.8901t 16460 min.540 - 72017 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S460N1.890116 < t 40440 min.540 - 72017 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S460N1.890140 < t 63430 min.540 - 72017 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S460N1.890163 < t 80410 min.540 - 72017 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S460N1.890180 < t 100400 min.540 - 72017 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S460N1.8901100 < t 150380 min.530 - 71017 min.6 min.normalized or normalized rolleddetails
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Yield Strength (MPa)Tensile Strength (MPa)% ElongationGrain SizeHeat TreatmentNotes
EN 10025-3:2004S460N1.8901150 < t 200370 min.530 - 71017 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420N1.8902t 16420 min.520 - 68019 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420N1.890216 < t 40400 min.520 - 68019 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420N1.890240 < t 63390 min.520 - 68019 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420N1.890263 < t 80370 min.520 - 68018 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420N1.890280 < t 100360 min.520 - 68018 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420N1.8902100 < t 150340 min.500 - 65018 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420N1.8902150 < t 200330 min.500 - 65018 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420N1.8902200 < t 250320 min.500 - 65018 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S460NL1.8903t 16460 min.540 - 72017 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S460NL1.890316 < t 40440 min.540 - 72017 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S460NL1.890340 < t 63430 min.540 - 72017 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S460NL1.890363 < t 80410 min.540 - 72017 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S460NL1.890380 < t 100400 min.540 - 72017 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S460NL1.8903100 < t 150380 min.530 - 71017 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S460NL1.8903150 < t 200370 min.530 - 71017 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420NL1.8912t 16420 min.520 - 68019 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420NL1.891216 < t 40400 min.520 - 68019 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420NL1.891240 < t 63390 min.520 - 68019 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420NL1.891263 < t 80370 min.520 - 68018 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420NL1.891280 < t 100360 min.520 - 68018 min.6 min.normalized or normalized rolleddetails
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)Yield Strength (MPa)Tensile Strength (MPa)% ElongationGrain SizeHeat TreatmentNotes
EN 10025-3:2004S420NL1.8912100 < t 150340 min.500 - 65018 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420NL1.8912150 < t 200330 min.500 - 65018 min.6 min.normalized or normalized rolleddetails
EN 10025-3:2004S420NL1.8912200 < t 250320 min.500 - 65018 min.6 min.normalized or normalized rolleddetails
EN 10025-4:2004S275M1.8818t 16275 min.370 - 53024 min.6 min.thermomechanically rolleddetails
EN 10025-4:2004S275M1.881816 < t 40265 min.370 - 53024 min.6 min.thermomechanically rolleddetails
EN 10025-4:2004S275M1.881840 < t 63255 min.360 - 52024 min.6 min.thermomechanically rolleddetails
EN 10025-4:2004S275M1.881863 < t 80245 min.350 - 51024 min.6 min.thermomechanically rolleddetails
EN 10025-4:2004S275M1.881880 < t 100245 min.350 - 51024 min.6 min.thermomechanically rolleddetails
EN 10025-4:2004S275M1.8818100 < t 120240 min.350 - 51024 min.6 min.thermomechanically rolleddetails
D) Impact Test Data
SpecificationDesignationSteel NumberTest PieceSection ThicknessAbsorbed EnergyTemp.Notes
J
mmAvgC
EN 10025-2:2004S235JR1.0038L, V, Ft 2502720details
EN 10025-2:2004S275JR1.0044L, V, Ft 2502720details
EN 10025-2:2004S355JR1.0045L, V, Ft 2502720details
EN 10025-2:2004S235J01.0114L, V, Ft 250270details
EN 10025-2:2004S235J21.0117L, V, Ft 40027-20details
EN 10025-2:2004S275J01.0143L, V, Ft 250270details
EN 10025-2:2004S275J21.0145L, V, Ft 40027-20details
EN 10025-2:2004S355J01.0553L, V, Ft 250270details
EN 10025-2:2004S355J21.0577L, V, Ft 40027-20details
EN 10025-2:2004S450J01.0590L, V, Ft 150270details
EN 10025-2:2004S355K21.0596L, V, Ft 15040-20details
L, V, F150 < t 40033-20details
EN 10025-3:2004S275N1.0490L, V, F---5520details
L, V, F---470details
L, V, F---43-10details
L, V, F---40-20details
EN 10025-3:2004S275NL1.0491L, V, F---6320details
L, V, F---550details
L, V, F---51-10details
L, V, F---47-20details
L, V, F---40-30details
L, V, F---31-40details
L, V, F---27-50details
EN 10025-3:2004S355N1.0545L, V, F---5520details
L, V, F---470details
L, V, F---43-10details
L, V, F---40-20details
EN 10025-3:2004S355NL1.0546L, V, F---6320details
L, V, F---550details
L, V, F---51-10details
L, V, F---47-20details
L, V, F---40-30details
L, V, F---31-40details
L, V, F---27-50details
EN 10025-3:2004S460N1.8901L, V, F---5520details
L, V, F---470details
L, V, F---43-10details
SpecificationDesignationSteel NumberTest PieceSection ThicknessAbsorbed EnergyTemp.
J
mmAvgC
L, V, F---40-20details
EN 10025-3:2004S420N1.8902L, V, F---5520details
L, V, F---470details
L, V, F---43-10details
L, V, F---40-20details
EN 10025-3:2004S460NL1.8903L, V, F---6320details
L, V, F---550details
L, V, F---51-10details
L, V, F---47-20details
L, V, F---40-30details
L, V, F---31-40details
L, V, F---27-50details
EN 10025-3:2004S420NL1.8912L, V, F---6320details
L, V, F---550details
L, V, F---51-10details
L, V, F---47-20details
L, V, F---40-30details
L, V, F---31-40details
L, V, F---27-50details
EN 10025-4:2004S275M1.8818L, V, F---5520details
L, V, F---470details
L, V, F---43-10details
L, V, F---40-20deta
A) Genaral Information
SelectSpecificationDesignationSteel NumberProduct FormAlloy GroupTitleNotesICS NumberStatus
EN 10025-4:2004S275ML1.8819bar, rod, plate, sheet, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 4: Technical Delivery Conditions for Thermomechanical Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-4:2004S355M1.8823bar, rod, plate, sheet, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 4: Technical Delivery Conditions for Thermomechanical Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-4:2004S420M1.8825bar, rod, plate, sheet, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 4: Technical Delivery Conditions for Thermomechanical Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
SelectSpecificationDesignationSteel NumberProduct FormAlloy GroupTitleNotesICS NumberStatus
EN 10025-4:2004S460M1.8827bar, rod, plate, sheet, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 4: Technical Delivery Conditions for Thermomechanical Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-4:2004S355ML1.8834bar, rod, plate, sheet, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 4: Technical Delivery Conditions for Thermomechanical Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-4:2004S420ML1.8836bar, rod, plate, sheet, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 4: Technical Delivery Conditions for Thermomechanical Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-4:2004S460ML1.8838bar, rod, plate, sheet, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 4: Technical Delivery Conditions for Thermomechanical Rolled Weldable Fine Grain Structural Steels---77.140.10, 77.140.50 Current
EN 10025-5:2004S355J0WP1.8945plate, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 5: Technical Delivery Conditions for Structural Steels with Improved Atmospheric Corrosion Resistancedetails77.140.10, 77.140.50 Current
EN 10025-5:2004S355J2WP1.8946plate, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 5: Technical Delivery Conditions for Structural Steels with Improved Atmospheric Corrosion Resistancedetails77.140.10, 77.140.50 Current
EN 10025-5:2004S235J0W1.8958bar, rod, plate, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 5: Technical Delivery Conditions for Structural Steels with Improved Atmospheric Corrosion Resistancedetails77.140.10, 77.140.50 Current
EN 10025-5:2004S355J0W1.8959bar, rod, plate, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 5: Technical Delivery Conditions for Structural Steels with Improved Atmospheric Corrosion Resistancedetails77.140.10, 77.140.50 Current
EN 10025-5:2004S235J2W1.8961bar, rod, plate, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 5: Technical Delivery Conditions for Structural Steels with Improved Atmospheric Corrosion Resistancedetails77.140.10, 77.140.50 Current
EN 10025-5:2004S355J2W1.8965bar, rod, plate, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 5: Technical Delivery Conditions for Structural Steels with Improved Atmospheric Corrosion Resistancedetails77.140.10, 77.140.50 Current
EN 10025-5:2004S355K2W1.8967bar, rod, plate, strip, shapealloy steelHot Rolled Products of Structural Steels - Part 5: Technical Delivery Conditions for Structural Steels with Improved Atmospheric Corrosion Resistancedetails77.140.10, 77.140.50 Current
EN 10025-6:2004S550Q1.8904plate, sheet, stripalloy steelHot Rolled Products of Structural Steels - Part 6: Technical Delivery Conditions for Flat Products of High Yield Strength Structural Steels in the Quenched and Tempered Condition---77.140.10, 77.140.50 Current
EN 10025-6:2004S460QL1.8906plate, sheet, stripalloy steelHot Rolled Products of Structural Steels - Part 6: Technical Delivery Conditions for Flat Products of High Yield Strength Structural Steels in the Quenched and Tempered Condition---77.140.10, 77.140.50 Current
SelectSpecificationDesignationSteel NumberProduct FormAlloy GroupTitleNotesICS NumberStatus
EN 10025-6:2004S460Q1.8908plate, sheet, stripalloy steelHot Rolled Products of Structural Steels - Part 6: Technical Delivery Conditions for Flat Products of High Yield Strength Structural Steels in the Quenched and Tempered Condition---77.140.10, 77.140.50 Current
EN 10025-6:2004S500QL1.8909plate, sheet, stripalloy steelHot Rolled Products of Structural Steels - Part 6: Technical Delivery Conditions for Flat Products of High Yield Strength Structural Steels in the Quenched and Tempered Condition---77.140.10, 77.140.50 Current
EN 10025-6:2004S620Q1.8914plate, sheet, stripalloy steelHot Rolled Products of Structural Steels - Part 6: Technical Delivery Conditions for Flat Products of High Yield Strength Structural Steels in the Quenched and Tempered Condition---77.140.10, 77.140.50 Current
EN 10025-6:2004S460QL11.8916plate, sheet, stripalloy steelHot Rolled Products of Structural Steels - Part 6: Technical Delivery Conditions for Flat Products of High Yield Strength Structural Steels in the Quenched and Tempered Condition---77.140.10, 77.140.50 Current
EN 10025-6:2004S500Q1.8924plate, sheet, stripalloy steelHot Rolled Products of Structural Steels - Part 6: Technical Delivery Conditions for Flat Products of High Yield Strength Structural Steels in the Quenched and Tempered Condition---77.140.10, 77.140.50 Current
EN 10025-6:2004S890QL11.8925plate, sheet, stripalloy steelHot Rolled Products of Structural Steels - Part 6: Technical Delivery Conditions for Flat Products of High Yield Strength Structural Steels in the Quenched and Tempered Condition---77.140.10, 77.140.50 Current
EN 10025-6:2004S550QL1.8926plate, sheet, stripalloy steelHot Rolled Products of Structural Steels - Part 6: Technical Delivery Conditions for Flat Products of High Yield Strength Structural Steels in the Quenched and Tempered Condition---77.140.10, 77.140.50 Current
EN 10025-6:2004S620QL1.8927plate, sheet, stripalloy steelHot Rolled Products of Structural Steels - Part 6: Technical Delivery Conditions for Flat Products of High Yield Strength Structural Steels in the Quenched and Tempered Condition---77.140.10, 77.140.50 Current
EN 10025-6:2004S690QL1.8928plate, sheet, stripalloy steelHot Rolled Products of Structural Steels - Part 6: Technical Delivery Conditions for Flat Products of High Yield Strength Structural Steels in the Quenched and Tempered Condition---77.140.10, 77.140.50 Current
B) Chemical Composition
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)CMnPSSiCrNiMoVAlCuTiNbNBZrNotes
EN 10025-4:2004S275ML1.8819t 400.13 max.1.50 max.0.025 max.0.020 max.0.50 max.0.30 max.0.30 max.0.10 max.0.08 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.------details
EN 10025-4:2004S275ML1.881940 < t 630.13 max.1.50 max.0.025 max.0.020 max.0.50 max.0.30 max.0.30 max.0.10 max.0.08 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.------details
EN 10025-4:2004S275ML1.881963 < t 1500.13 max.1.50 max.0.025 max.0.020 max.0.50 max.0.30 max.0.30 max.0.10 max.0.08 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.------details
EN 10025-4:2004S355M1.8823t 400.14 max.1.60 max.0.030 max.0.025 max.0.50 max.0.30 max.0.50 max.0.10 max.0.10 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.------details
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)CMnPSSiCrNiMoVAlCuTiNbNBZrNotes
EN 10025-4:2004S355M1.882340 < t 630.14 max.1.60 max.0.030 max.0.025 max.0.50 max.0.30 max.0.50 max.0.10 max.0.10 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.------details
EN 10025-4:2004S355M1.882363 < t 1500.14 max.1.60 max.0.030 max.0.025 max.0.50 max.0.30 max.0.50 max.0.10 max.0.10 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.------details
EN 10025-4:2004S420M1.8825t 160.16 max.1.70 max.0.030 max.0.025 max.0.50 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S420M1.882516 < t 400.16 max.1.70 max.0.030 max.0.025 max.0.50 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S420M1.882540 < t 630.16 max.1.70 max.0.030 max.0.025 max.0.50 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S420M1.882563 < t 1500.16 max.1.70 max.0.030 max.0.025 max.0.50 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S460M1.8827t 160.16 max.1.70 max.0.030 max.0.025 max.0.60 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S460M1.882716 < t 400.16 max.1.70 max.0.030 max.0.025 max.0.60 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S460M1.882740 < t 630.16 max.1.70 max.0.030 max.0.025 max.0.60 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S460M1.882763 < t 1500.16 max.1.70 max.0.030 max.0.025 max.0.60 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S355ML1.8834t 400.14 max.1.60 max.0.025 max.0.020 max.0.50 max.0.30 max.0.50 max.0.10 max.0.10 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.------details
EN 10025-4:2004S355ML1.883440 < t 630.14 max.1.60 max.0.025 max.0.020 max.0.50 max.0.30 max.0.50 max.0.10 max.0.10 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.------details
EN 10025-4:2004S355ML1.883463 < t 1500.14 max.1.60 max.0.025 max.0.020 max.0.50 max.0.30 max.0.50 max.0.10 max.0.10 max.0.02 min.0.55 max.0.05 max.0.05 max.0.015 max.------details
EN 10025-4:2004S420ML1.8836t 160.16 max.1.70 max.0.025 max.0.020 max.0.50 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S420ML1.883616 < t 400.16 max.1.70 max.0.025 max.0.020 max.0.50 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S420ML1.883640 < t 630.16 max.1.70 max.0.025 max.0.020 max.0.50 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S420ML1.883663 < t 1500.16 max.1.70 max.0.025 max.0.020 max.0.50 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S460ML1.8838t 160.16 max.1.70 max.0.025 max.0.020 max.0.60 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S460ML1.883816 < t 400.16 max.1.70 max.0.025 max.0.020 max.0.60 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)CMnPSSiCrNiMoVAlCuTiNbNBZrNotes
EN 10025-4:2004S460ML1.883840 < t 630.16 max.1.70 max.0.025 max.0.020 max.0.60 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-4:2004S460ML1.883863 < t 1500.16 max.1.70 max.0.025 max.0.020 max.0.60 max.0.30 max.0.80 max.0.20 max.0.12 max.0.02 min.0.55 max.0.05 max.0.05 max.0.025 max.------details
EN 10025-5:2004S355J0WP1.8945t 400.12 max.1.0 max.0.06 - 0.150.035 max.0.75 max.0.30 - 1.25------------0.25 - 0.55------0.009 max.------details
EN 10025-5:2004S355J2WP1.8946t 400.12 max.1.0 max.0.06 - 0.150.030 max.0.75 max.0.30 - 1.25------------0.25 - 0.55---------------details
EN 10025-5:2004S235J0W1.8958t 1500.13 max.0.20 - 0.600.035 max.0.035 max.0.40 max.0.40 - 0.80------------0.25 - 0.55------0.009 max.------details
EN 10025-5:2004S355J0W1.8959t 1500.16 max.0.50 - 1.500.035 max.0.035 max.0.50 max.0.40 - 0.80------------0.25 - 0.55------0.009 max.------details
EN 10025-5:2004S235J2W1.8961t 1500.13 max.0.20 - 0.600.035 max.0.030 max.0.40 max.0.40 - 0.80------------0.25 - 0.55---------------details
EN 10025-5:2004S355J2W1.8965t 1500.16 max.0.50 - 1.500.030 max.0.030 max.0.50 max.0.40 - 0.80------------0.25 - 0.55---------------details
EN 10025-5:2004S355K2W1.8967t 1500.16 max.0.50 - 1.500.030 max.0.030 max.0.50 max.0.40 - 0.80------------0.25 - 0.55---------------details
EN 10025-6:2004S550Q1.89043 t 500.20 max.1.70 max.0.025 max.0.015 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S550Q1.890450 < t 1000.20 max.1.70 max.0.025 max.0.015 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S550Q1.8904100 < t 1500.20 max.1.70 max.0.025 max.0.015 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S460QL1.89063 t 500.20 max.1.70 max.0.020 max.0.010 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S460QL1.890650 < t 1000.20 max.1.70 max.0.020 max.0.010 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S460QL1.8906100 < t 1500.20 max.1.70 max.0.020 max.0.010 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S460Q1.89083 t 500.20 max.1.70 max.0.025 max.0.015 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S460Q1.890850 < t 1000.20 max.1.70 max.0.025 max.0.015 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S460Q1.8908100 < t 1500.20 max.1.70 max.0.025 max.0.015 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S500QL1.89093 t 500.20 max.1.70 max.0.020 max.0.010 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
SpecificationDesignationSteel NumberSection Thickness / Diameter (mm)CMnPSSiCrNiMoVAlCuTiNbNBZrNotes
EN 10025-6:2004S500QL1.890950 < t 1500.20 max.1.70 max.0.020 max.0.010 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S620Q1.89143 t 500.20 max.1.70 max.0.025 max.0.015 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S620Q1.891450 < t 1000.20 max.1.70 max.0.025 max.0.015 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S620Q1.8914100 < t 1500.20 max.1.70 max.0.025 max.0.015 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S460QL11.89163 t 500.20 max.1.70 max.0.020 max.0.010 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S460QL11.891650 < t 1000.20 max.1.70 max.0.020 max.0.010 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S460QL11.8916100 < t 1500.20 max.1.70 max.0.020 max.0.010 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S500Q1.89243 t 500.20 max.1.70 max.0.025 max.0.015 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S500Q1.892450 < t 1500.20 max.1.70 max.0.025 max.0.015 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S890QL11.89253 t 500.20 max.1.70 max.0.020 max.0.010 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S890QL11.892550 < t 1000.20 max.1.70 max.0.020 max.0.010 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S550QL1.89263 t 500.20 max.1.70 max.0.020 max.0.010 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15 max.details
EN 10025-6:2004S550QL1.892650 < t 1000.20 max.1.70 max.0.020 max.0.010 max.0.80 max.1.50 max.2.0 max.0.70 max.0.12 max.---0.50 max.0.05 max.0.06 max.0.015 max.0.0050 max.0.15
