J- 2 Surface Roughness Testing TESA RUGOSURF 10G Surface roughness gage TESA –TECHNOLOGY Genuine Swiss Made Quality RUGOSURF 10G is a portable and versa- tile roughness gage that can be used in the workshop, for incoming inspection or in the laboratory. This heavy-duty hand-held tool offers a wide range of accessories and can be used in a number of applications that’s virtually unlimited. Technical Data Table of measured roughness parameters International Standards ISO 4287 Ra Rq Rt Rz Rp Rv Rc RSm Rδc Rpc 1997 Rk Rpk Rvk Mr1 Mr2 Pa Pq Pt Pp Pv Pc Psm Pδc Ppc Din Rmax R3z R3zm ISO 12085 R AR Rx Rke Rpke Ryke Measuring range 0 + 300 μm / 0 + 12 μin Resolution 0.005 μm / 0.02 μin Cut-offs (Ic in in) 0.01 in 0.03 in 0.1 in Total length (Im in in) 0.05 in 0.15 in 0.5 in Traversing length (Ic in in) 0.06 in 0.18 in 0.6 in Possible selection of 2,3,4 or 5 cut-offs for the measurement (length from 0.75 to 16 mm)
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
J-2
Surface Roughness Testing
TESA RUGOSURF 10G Surface roughness gage
TESA –TECHNOLOGYGenuine Swiss Made Quality
RUGOSURF 10G is a portable and versa-tile roughness gage that can be used in theworkshop, for incoming inspection or in thelaboratory. This heavy-duty hand-held tooloffers a wide range of accessories and canbe used in a number of applications that’svirtually unlimited.
Technical DataTable of measured roughness parametersInternational StandardsISO 4287 Ra Rq Rt Rz Rp Rv Rc RSm Rδc Rpc1997 Rk Rpk Rvk Mr1 Mr2
Pa Pq Pt Pp Pv Pc Psm Pδc PpcDin Rmax R3z R3zmISO 12085 R AR Rx Rke Rpke Ryke
Measuring range 0 + 300 µm / 0 + 12 µinResolution 0.005 µm / 0.02 µinCut-offs (Ic in in) 0.01 in 0.03 in 0.1 inTotal length(Im in in) 0.05 in 0.15 in 0.5 inTraversing length (Ic in in) 0.06 in 0.18 in 0.6 in
Possible selection of 2,3,4 or 5 cut-offs for the measurement (length from 0.75 to 16 mm)
Summary of Roughness ParametersCommonly UsedArithmetical mean deviation of the profile Ra (ISO 4287, DIN 4768)
The arithmetical mean deviation Ra is the mean value of the absolute valueof the profile departure y within the reference length l.
Max. profile valley depth Rmax (DIN 4768)
Among the existing single roughness depths Zi, the max. profile valley depthRmax counts for the most significant within the total measuring length lm.
According to ISO 4288 and DIN 4287 - Part 1, this parameter is also specified as Ry max.
Mean roughness depth Rz DIN (DIN 4768)
The mean roughness depth Rz is the arithmetical mean of the single rough-ness depths of successive sampling lengths le.
According to ISO 4287 and DIN 4762, the parameter Rz DIN is also specified as Ry5.
Because Rz is named differently in DIN 4768 and ISO 4287, this para mater isalso specified as Rz DIN or Rz ISO.
When the parameter Rz is measured according to DIN, it is generally admit-ted that the extreme value ISO is also matched providing thatRz ISO is not exceeding Rz DIN .
Application of Roughness Comparison SpecimensThese specimens for testing the surface finish quality have long proven theirvalue in practical use.
They serve for touch and/or sight comparisons with the surface of the work-pieces that are manufactured using the same method. Condition is thatmaterials have to be comparable.
The comparison of the roughness of theworkpiece surface is not quantitativelyexpressed. The extent to which the surfacesof both the specimen and the workpiece arematched is appreciated subjectively only.
Sight comparison requires optimum lightsource angle. For small surfaces, the use ofa magnifying glass with up to 8x magnifica-tion is recommended.
Touch comparison is made using the fingernail or a small copper piece like a coin, forinstance.
06930000 29527 Rugosurf 100 S, for probes with contact skids 06930001 29910 Rugosurf 100 SF, for probes without contact skids06930002 29911 Rugosurf 100 S-CNOMO, for probes with contact skids06930003 29912 Rugosurf 100 SF-CNOMO, for probes without contact skids
�
Probe system:Hall EffectTechnology,
analogue with high-linearoutput signal.90° diamond stylus, radius 5 μm25 mm contact skid (TESA standard probe STS)
Stylus force in static
measuring: < 0,5 mN (DIN 4772)Resting force on contactskids: < 0,15 mN
Class 1 (± 5%) as per DIN 4772
Linearity: < 2% throughoutthe measuring range, temperature compensationfrom 0 to 60 °C
Probing speed:0,8 mm/s
Reverse speed: approx. 2,0 mm/s
Rechargeable batteries with μPcontrolled checkThermal printer for all measuredvalues plus curve tp
RS-232 digital output
80%, with no con-densation
10 °C to 40 °C
130 x 78 x 245 mm
700 g
�
Suited plastic case
Declaration ofconformity
TESA Surface Roughness Gage RUGOSURF 100Versatile roughness gauge designed for measuring roughness parametersaccording to ISO 4287/1, DIN 4768, 4772, 4777 or CNOMO (ISO 12085). A wide variety of interchangeable probes allows you to solve specific applications, such as roughness measurements on surfaces of grooves, smallbores, cylinders, steel balls etc.• Measured parameters: Ra, Rz DIN, Rmax, R3z, Rt, Rq RMS along with
printed profile bearing portion tp.• Integrated thermal printer.• Choice of cut-offs from 0.08 to 2.5 mm.• Traversing length lt from 0.48 to 15.0 mm.• RS-232 digital output compatible with PC.• Possible storage of the last 50 measured values.• Drive unit with or without contact skids.• Easily interchangeable probes (Hall Effect Technology).
Roughness Gages
RUGOSURF 100CNOMO
S SF S SFControl unit � �
CNOMO control unit � �
S type measuring unit � �
SF type measuring unit Battery charger, 90 - 230 Vac + Adapter EU/US � �
TESA standard probe STS � � � �
Connecting cable � � � �
Roughness specimen, nominal value Ra = 2,95 µm � � � �
Probe for measuring concave or convex surfaces(radius from 3 mm, lc = 0.08 mm, lt = 0.48 mm)
Probe for measuring grooves (with contact skids fordepth up to 15 mm)
Type CCS No. 06960004 Type SLS No. 06960005
Ø 8Ø
3.5
27.0
4.5
Ø 8Ø
3.5
27
10 Ø4.
3
2
ca. 1.5
Standard probe Probe for checking gear tooth flanks (module from 1,5)
Type STS No. 06960006 Type TFS No. 06960007
Ø8.0
Ø 7
.0
27
Ø 3
.5
90
18
S / SF
Ø 8
22
ca. 1
28
b = 13 mm
Transverse probe
Probe for depth measurement
Type TRS No. 06960008
Ø 8
ca. 140
13
917
8
1
Tangent from 4 mm diameter
Type CBS No. 06960010
Type BAS No. 06960009
Probes without contact skids (for use with the SF drive unit)
Ø 8Ø
3.5
28
Ø 3.5
1
Ø 8Ø
3
26
14
1 / 0
.6
Transverse chisel probe. Measures small shafts(max. diameter: 1.0 mm), sharp edges etc.
BOSF-1.5: probe for small bores and gear toothflanks, module from 0.75, 1.5 mm diameterBOSF-1.0: probe for small bores and gear toothflanks, module from 0.5, 1.0 mm diameter
Type AKSF No. 06960011 Type BOSF-1.5 No. 06960012Type BOSF-1.0 No. 06960013
SLSF-15: probe for slots. Max. depth: 15 mmSLSF-10-1.5: probe for slots. Max. depth: 10 mm,min. width: 1.5 mmSLSF-20: probe for slots. Max. depth 20 mm (on request)
X = 15 mm, type SLSF-15 No. 06960014X = 10 mm, type SLSF-10-1.5 No. 06960015X = 20 mm, type SLSF-20 No. 06960016
Ø 8
26
7
Ø 3
.5
max
. 20
mm
LASF
RASF
LASF, angled, left-hand side model, 20 mmRASF, angled, right-hand side model, 20 mmLASF-10, angled, left-hand side model, 10 mm(No. 06960019)RASF-10, angled, right-hand side model, 10 mm(No. 06960020)
Type LASF No. 06960017Type RASF No. 06960018
Additional accessories
06960021 29935 EX100 Extension, 100 mm (for STS probe only)
06960022 29936 RS-3 Roughness specimen, nominal value Ra = 3 μm, 3% (as standard)06960023 29937 RS-0.8 Reference specimen, nominal value Ra = 0.7-0.8 μm, 8%06960024 29938 RSGM Roughness specimen in glass, nominal value Ra = 0.5-2.5 μm06960025 29939 RSGH Roughness specimen in glass, nominal value Ra > 2.51 μm06960026 29976 RSGL Roughness specimen in glass, nominal value Ra < 0.49 μm
06960027 29977 MESU Measuring support, complete with granite plate06960028 29978 AMU Adapter for both S and SF drive units06960029 29979 CP90 Connector, 90°06960030 29980 PR-20 Thermal paper roll, 20 items
Pocket Surf® Gage The Pocket Surf gage is a pocket-sized, economically priced, completelyportable instrument for performing traceable surface roughness measurementson a wide variety of surfaces (including small inside diameters). The PocketSurf gage is solidly built with a durable cast aluminum housing to provide years of accurate, reliable surface finish gaging. Designed for use in a shopenvironment or in the laboratory, the Pocket Surf works on both horizontal andvertical surfaces. It can be used at any angle and can even be held upside-down. For even greater versatility, it operates in four probe positions – closedor with the probe at 90˚, 180˚ or 270˚. Use the Pocket Surf for flat surfaces ofboth, inside and outside diameters, as well as many difficult-to-gage surfaces.
CapabilitiesThe Pocket Surf can measure any one of four switch-selectable parameters.
• Ra Average Roughness• Ry Maximum Roughness Depth• Rmax Maximum Roughness Depth (DIN)• Rz Mean Roughness Depth (DIN), also called Rtm
Rmax and Ry are convenient “burr” and “scratch” control parameters and valu-able additions to Ra and Rz. The gage’s digital display is conveniently locatedon the top of the unit for optimum visibility. The easy-to-read LCD readoutpresents the measured roughness value, in microinches or micrometers, withinhalf a second after the surface is traversed. Out-of-range (high or low) and“battery low” signals are also displayed.
Selectable Traverse Length 1, 3, or 5 cutoffs of .030" (0.8 mm) each, permit checking surface lands as shortas .075" (1.9 mm). The start switch is centrally located for optimum stability.
4 possible measuring positions of the stylus
�
Measuring prin-ciple of the contact
system, piezoelectric
3-digit LC display
0.01 μm1 μin
See adjoiningtable
Class 2 (± 10%)
according to DIN 4772
Cut-off : 0.03 in /0.8 mm
(ANSI 2RC filter)
The total measuringlength lm may be set for 1, 3, or 5 cut-off lengths
Feed rateVt : 5 mm / s
15 mN
RS-232
9V alkaline bat-tery, IEC 6F22
≈ 3000 h
Durable castaluminum
housing
50°F to 113°F
- 4°F to 149°F
Basic instrumentwithout probe:
5.5 x 3 x 1 in
Basic instr. withoutprobe: ≈435 g
Plastic case
Declaration of conformity.
Available upon request :reference standard No. 81.60000 with calibration certificate
Ra / Ry .075 / 2.0 .030 / 0.8 1 .135 / 3.5 .090 / 2.4 3
Ra / Rz / Rmax .195 / 5.0 .150 / 4.0 5
Evaluation Lengthin / mm
Number of Cutoffs/Switch Position
Traverse Lengthin / mm
Pocket Surf Measurement ParametersRa — Roughness AverageThe arithmetic average height of roughness irregularities measured from a mean line within the evaluation length (L).
Rmax — Maximum Roughness Depth (per DIN)The largest of the 5 maximum peak-to-valley roughness depths in 5 succes-sive sampling lengths. In the illustration below, Rmax (DIN) = Ry 4
Rz — Mean Roughness Depth (per DIN), also known as Rtm
The mean of 5 maximum peak-to-valley roughness depths in 5 successivesampling lengths
Note: To fully meet the requirements of DIN 4768 for Rmax and Rz, probes having a stylus radius of .0002" (5 µm) are available.
Ry — Maximum Roughness DepthFor the evaluation length equaling one cutoff, it is the vertical distance betweenthe highest peak and the deepest valley within the sampling length. For theevaluation length equaling 3 cutoffs, it is the largest of the 3 maximum peak-to-valley roughness depths in 3 successive sampling lengths.
Probe VarietyA variety of probes are easily interchangeable, increasing the gage’s capabilityfor a wide range of applications, such as flats, O.D.s, I.D.s (including smallbores), sharp edges, inside “O” ring grooves, short lands and shoulders.
Built-in Digital OutputWith built-in digital output, the Pocket Surf gage is designed for SPC applications and is compatible with most major SQC datacollection systems. Although it provides powerful flexibility for a portable sur-face finish gage, the Pocket Surf gage uses a regular, consumer-type, 9 voltalkaline battery. Data can be output through an RS-232 port and printed on aBrown & Sharpe SPC printer.
Portable Vee FixtureThe Portable Vee Fixture simplifies themeasurement of small outside diameterparts up to 1" (25mm). This optionalaccessory comes complete with a PS-145 setting pin.
599-4000-2421 26841
Height StandCompact and convenient, an optionalheight stand with bracket is available asa holding fixture for the Pocket Surf gage.This optional accessory holds the PocketSurf both horizontally and vertically,making it easy to take measurementson a surface plate or on any suitable,flat working surface.
599-4000-2496 26843
Swivel Fixture for Mounting on Height Gage DP.For added flexibility, the Swivel Fixtureallows the Pocket Surf to be moved and locked into position at any angle.Complete with a T-Bar attachment fixture, the Swivel Fixture will work with most standard column gages andheight stands.
599-4000-2500 26899
Height Stand with Swivel FixtureFor maximum convenience and flexibil-ity, purchase the Height Stand togetherwith the Swivel Fixture. This completeset will give you a fully functional holdingfixture for your Pocket Surf gage, allow-ing you to position the tool horizontally,vertically, or at any angle in between.
Parallel Chisel Probe (Optional extra)A 90˚ sapphire chisel, .0004" (10μm)radius. Gages sharp edges or smallO.D.s where probe is perpendicular (in 90˚ or 270˚ position) to axis of traverse.Also for O.D.s smaller than .25" (6.35 mm)staged on 599-4000-2421 Vee Fixture.
599-4000-1020-2 26836
Transverse Chisel Probe (Optional extra)A 90˚ sapphire chisel, .0004" (10μm)radius. Gages sharp edges or smallO.D.s where probe is aligned with (in 180˚or closed position) axis of traverse.
599-4000-1020-1 26835
Groove Bottom Probe (Optional extra)A 90˚ conical diamond stylus, .0004"(10μm) radius. Gages grooves,recesses and holes to depths of .25"(6.35 mm). Also used for short landsand shoulders.
Note: Groove Bottom Probes can onlybe used in the “180˚ position” with thePocket Surf unit supported in a heightstand or other fixture.
599-4000-1028 26840
Small Bore Probe (Optional extra)A 90˚ conical diamond stylus, .0002"(5μm) radius. Gages small bores (1/8" [3.2 mm] min I.D.) up to a depth of 3/4" (19 mm).
Note: Small Bore Probes can only beused in the “180˚ position” with thePocket Surf unit supported in a heightstand or other fixture.
599-4000-1027 26839
Small Bore Probe (Optional extra)A 90˚ conical diamond stylus, .0004"(10μm) radius. Gages small bores (1/8" [3.2 mm] min I.D.) up to a depth of 3/4" (19 mm).
Note: Small Bore Probes can only beused in the “180˚ position” with thePocket Surf unit supported in a heightstand or other fixture.
599-4000-1021 26837
General Purpose ProbesA 90˚ conical diamond stylus, .0004" (10μm)radius per ANSI–B46.1, ISO, and MIL specs.
599-4000-1019 26834A 90˚ conical diamond stylus, .0002"(5μm) radius per DIN 4768 and certainISO specs. This probe is identified byyellow dot at end of connector.