Bridge Corrosion A look at the corrosion of steel in Bridges
Mar 29, 2015
Bridge CorrosionA look at the corrosion of
steel in Bridges
Steel Life Cycle
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Iron ore
Blast furnace - reduction to iron
Steelmaking furnace (add carbon)
Structural steel
Oxidation of iron - rust
How a bridge cable is made
• Cables are made of thousands of individual steel wires bound tightly together. Steel, which is very strong under tension, is an ideal material for cables; a single steel wire, only 0.1 inch thick,
can support over half a ton without breaking.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Suspension Bridges• The towers are built up from reinforced concrete or steel, with a
gap for the main roadway. Then the anchorages are installed to hold the cables. Very thin steel cable is spun from between the anchorages until it can be gathered together to form two large cables. Other cables are then dropped down from the main cables and the sections of prefabricated roadway are attached to them.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Corrosion
• This is the last stage of a steel product’s life cycle.
• When steel is exposed to water and oxygen, it rusts
• Forms iron oxideQuickTime™ and a
TIFF (Uncompressed) decompressorare needed to see this picture.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Ways to prevent corrosion
• Protective coatings
plating with another metal painting
galvanized steel
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Preventing Corrosion
• Use corrosion resistant metalex: stainless steel
Only problem?
Stainless steel is an alloy of chromium
and is therefore a heck of a lot more
expensive than regular steel!
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Gateway Arch, St. Louis
Preventing Corrosion
• Anodic/Cathodic protectiona technique used to control the corrosion of a
metal surface by making it work as a cathode. This is achieved by placing in contact with the metal to be protected another more easily corroded metal to act as the anode.
Aluminum cathodes on steel
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Anodic region
• The negative part of the cell to which current flows• Oxidation occurs (gaining electrons)• Rust forms• The more reactive metal!
Zinc anode
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Cathodic region
• The positive part of the cell to which current flows from• No rust forms• Less reactive metal
• The area turns pink in phenolphthalein indicator (its basic!)
Steel (Iron) pipe cathode
What do you think?
• If you were to use anode/cathode protection for a piece of copper wrapped in zinc, which metal would be rusted?
• (remember the more reactive metal will be the anode and rust!)
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Corrosion Impact
• Approximately 20% of all the iron and steel produced is used to repair or replace corroded structures. (and this cost billions of dollars each year in repair and maintenance costs!)
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.