APPLICATION OF CATALYTIC CONVERTER It basically converts harmful gases into harmless gases, whichare environment friendly, with the help of a catalyst.Engine exhausts having harmful gases like CO, NOx & HC which are converted into harmless gase s like CO2, N2 & H2O respectively with the use of catalytic converterTwo-way catalytic converter is widely used on diesel enginesto reduce hydrocarbon and carbon monoxide emissions. They were also used on gasoline engines in American- and Canadian-market automobiles until 1981. Because of their inability to control oxides ofnitrogen,Three-way (oxidation-reduction) catalytic converters have been used in vehicle emission control systems in the United States and Canada; many other countries have also adopted stringent vehicle emission regulationsthat in effect require three-way converters on gasoline-powered vehicles. A three-way catalytic converter has three simultaneous tasks: 1.Reductionof nitrogen oxides tonitrogenandoxygen: 2NO x → xO 2 + N 2 2.Oxidationof carbon monoxide to carbon dioxide: 2CO + O 2 → 2CO 2 3.Oxidation of unburnt hydrocarbons (HC) to carbon dioxide and water: C x H 2x+2 + [(3x+1)/2]O 2 → xCO 2 + (x+1)H 2 O The primary use of this element is in automobiles as a catalytic converter , which changes harmful emissions from the engine into less polluting gases. Three-way catalytic converters can store oxygen from the exhaust gas stream, usually when the air-fuel ratiogoes lean.When insufficient oxygen is available from the exhaust stream, the stored oxygen is released and consumed . Alack of sufficient oxygen occurs either when oxygen derived from NO x reduction is unavailable or when certain maneuvers such as hard acceleration enrich the mixture beyond the ability of the converter to supply oxygen. Rhodium-based catalysts are used in a number of industrial processes; notably, in the automobilecatalytic convertersand for catalytic carbonylation of methanol to produce acetic acidby theMonsanto process. It is also used to catalyze addition of hydrosilanes to molecular double bonds, a process important in manufactur e of certain silicone rubbers.Rhodium catalysts are also used to reducebenzenetocyclohexane ..Rhodium finds use injewelryand for decorations. It is electroplated on white goldand platinum to give it a reflective white surface. This is known as rhodium flashing in the jewelry business. It may also be used in coatingsterling silver to protect against tarnish, which issilver sulfide(Ag 2 S) produced from the atmospheric hydrogen sulfide (H 2 S). Solid (pure) rhodium jewelry is
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
8/4/2019 Benazir Or
http://slidepdf.com/reader/full/benazir-or 1/11
APPLICATION OF CATALYTIC CONVERTER
It basically converts harmful gases into harmless gases, whichare environment
friendly, with the help of a catalyst.Engine exhausts having harmful gases like CO, NOx
& HC which are converted into harmless gases like CO2, N2 & H2O respectively with
the use of catalytic converter
Two-way catalytic converter is widely used on diesel engines to reduce hydrocarbon and
carbon monoxide emissions. They were also used on gasoline engines in American- and
Canadian-market automobiles until 1981. Because of their inability to control oxides of
nitrogen,
Three-way (oxidation-reduction) catalytic converters have been used in vehicle emission control
systems in the United States and Canada; many other countries have also adopted stringent
vehicle emission regulations that in effect require three-way converters on gasoline-powered
vehicles. A three-way catalytic converter has three simultaneous tasks:
1. Reduction of nitrogen oxides to nitrogen and oxygen: 2NOx → xO2 + N2
2. Oxidation of carbon monoxide to carbon dioxide: 2CO + O2 → 2CO2
3. Oxidation of unburnt hydrocarbons (HC) to carbon dioxide and water: CxH2x+2 +
[(3x+1)/2]O2 → xCO2 + (x+1)H2O
The primary use of this element is in automobiles as a catalytic converter, which changes
harmful emissions from the engine into less polluting gases.
Three-way catalytic converters can store oxygen from the exhaust gas stream, usually when the
air-fuel ratio goes lean.When insufficient oxygen is available from the exhaust stream, the stored
oxygen is released and consumed. Alack of sufficient oxygen occurs either when oxygen derived
from NOx reduction is unavailable or when certain maneuvers such as hard acceleration enrich
the mixture beyond the ability of the converter to supply oxygen.
Rhodium-based catalysts are used in a number of industrial processes; notably, in the
automobile catalytic converters and for catalytic carbonylation of methanol to produce acetic
acid by the Monsanto process. It is also used to catalyze addition of hydrosilanes to molecular
double bonds, a process important in manufacture of certain silicone rubbers.Rhodium
catalysts are also used to reduce benzene to cyclohexane.
.
Rhodium finds use in jewelry and for decorations. It is electroplated on white gold and platinum
to give it a reflective white surface. This is known as rhodium flashing in the jewelry business. It
may also be used in coating sterling silver to protect against tarnish, which is silver sulfide
(Ag2S) produced from the atmospheric hydrogen sulfide (H2S). Solid (pure) rhodium jewelry is
very rare, because the metal has both high melting point and poor malleability (making such
jewelry very hard to fabricate) rather than due to its high price. Additionally, iassures that most
of its jewelry usage is in the form of tiny amounts of power (commonly called rhodium sponge)
dissolved into electroplating solutionsts .
It is also used as a filter in mammography systems because of the characteristic X-rays it
produces.
Rhodium is also used to coat some parts of high-quality fountain pens due to its high
reflectance, as well as its chemical and mechanical resistance.
Rhodium neutron detectors are used in combustion engineering nuclear reactors to
measure neutron flux levels – a method that requires a digital filter to determine the
current neutron flux level, as there are three signals generated: immediate, a fewseconds later, and a minute later, each with its own signal level, and all three are
combined in the rhodium detector signals. The three Palo Verde nuclear reactors each
have 305 rhodium neutron detectors, 61 detectors on each of 5 vertical levels, providing
an accurate 3-D "picture" of reactivity and allowing fine tuning to most economically
Reducing amount of CO, HC and NOx, particulate emission, it leads to pollution free
environment. It is having long life.
An increase in peak engine horsepower can be achieved. Gas mileage can be increased in a well designed aftermarket system.
Aftermarket parts can be cost effective replacements for stock parts when OEM parts are
not readily available (or are more expensive).
Aftermarket parts are often available in longer lasting stainless steel, whereas many OEM
exhaust components are made from mild steel and have a limited lifespan.
DISADVANTAGES OF CATALYTIC CONVERTER
Cost is high.
Volume required is high
Some amount of weight is added
There is over temperature problem. Heat shields required otherwise areas around it will
beseverely due to thermal stresses. Catalytic material is lost. Unleaded fuel is required
otherwise lead will be replacethe catalyst and so no reactions will be carried out
Removing or bypassing a catalytic converter may interfere with emission laws in some
jurisdictions.
A noticeable increase in noxious fumes may result (particularly when the catalytic
converter is removed or bypassed, and/or when exhaust outlets are rerouted to the side
of the car as with side-exit exhausts).
Engine sound may be more noticeable to both driver and pedestrians, resulting in
increased noise pollution.
An incorrectly designed exhaust can cause loss of low-RPM torque, and a decrease in
fuel economy.
8/4/2019 Benazir Or
http://slidepdf.com/reader/full/benazir-or 4/11
THE FUTURE OF CATALYTIC CONVERTER
The Four-Way Catalytic Converter consists of a three-way catalytic converter and one more
component, which reduces CO2. The different components reduce all known harmful car
emissions.
The newly-designed component uses a completely different process than any of the units of
the three-way catalytic converter. First the exhaust from the car goes through the three-way
catalytic converter. Then the exhaust goes through a pipe into a chamber containing a fan
on one end. The fan would blow all of the exhaust against a high aluminum content zeolite
on the other end of the chamber. It is a CO2 adsorbent which means that only
CO2 would be let through to the subsequent chamber (University of Oviedo). A CO2 sensor
would be in the pipe leading to the next chamber. Then, when approximately 14.67 grams of
CO2 are collected in the next chamber, (Toreki) the fan would deactivate, and the excess
exhaust would drift out into the air. These exhausts consist of H2O, N2, and oxygen and are
completely harmless to the environment and humans (Nice). Back in the chamber with theCO2, the chamber would seal itself off to prevent other gases from entering. Then, 16
grams of burning magnesium would be dropped into the chamber from a chute above
(Toreki). The supply of magnesium could be refilled at gas stations like gasoline. The
reaction causes the reactants to reach a temperature of 2000 degrees Celsius(Toreki). As
well, the reaction emits a bright light. Surrounding the chamber are three layers. The
innermost layer is made of a see-through material embedded with quantum dots. When the
quantum dots are manufactured in a certain way, they emit light when heated to a high
temperature (Poole & Owens). The second layer contains a layer of photovoltaic cells
(i.e., solar panels). The third, outermost, layer is an outside shell that contains the entire
assembly. So, when the reaction is initiated by the introduction of magnesium into the
chamber, it heats up the quantum dots and causes the dots to emit light. Then, the light fromthe quantum dots as well as from the reaction itself charges the photovoltaic cells. The
electrical energy generated by the photovoltaic cells goes down a conducting wire to the car
battery, thereby continuously generating energy for the car. The by-products of this reaction
are white magnesium oxide and black carbon. When the reaction is over, the floor of the
reaction chamber opens up so that the byproducts drop down into a collection chamber. The
byproducts could be emptied out at gas stations, where they could be transported to
processing centers that can utilize the byproducts. For instance, white magnesium oxide
can be used to preserve books, and black carbon can act as a substitute for salt in melting
snow. This process is repeated over and over again throughout a car ride.
Quantum dots are found in two aspects of the Four-Way Catalytic Converter: on the inner layer
of the reaction chamber and on the photovoltaic cells. Based on current technologies, when a
light photon hits a photon absorber, it typically releases only one electron. Once it becomes
commercially feasible to manufacture photon absorbers at the quantum scale (i.e., less than 100
nanometers in length, width and height), it has been shown that one photon could release as
many as seven electrons (Jobwerx). This would make the Four-Way Catalytic Converter almost
8/4/2019 Benazir Or
http://slidepdf.com/reader/full/benazir-or 5/11
seven times more efficient. As well, quantum dots of a heat-resistant material would have to be
manufactured for the inner layer of the reaction chamber. Manufacturers would have to use
extremely acute and fast machines to efficiently mass-produce the quantum dots.
CONCLUSION
1- It is found that the reason behind the increase of totalhydrocarbon (THC) in compressed natural gas (CNG)operated vehicle over that produced in gasoline operatedvehicle is due to the difficulty in oxidizing the unburnedhydrocarbons in the exhaust gases, where the oxidizationof hydrocarbons is one of the functions of the three –waycatalyzer. The exhaust hydrocarbons of a gas-operatedvehicle have a significantly different composition to thoseof a gasoline-operated vehicle.2- The effectiveness of catalytic converter (catalyzer) inthe condition of idle state is much better than that fortransient state based on the European Driving Cycle(ECE-15) shown in Figure 3, where in the case of idle
state, the catalyzer is fully warm and hence operating atit's maximum efficiency, while for the case of transientstate condition the effectiveness is not very well, wherethe catalyzer was faced by air flow and temperaturechanges rapidly.3- In the case of catalyst conversion efficiency, thecatalytic converter reduces the amount of both CO andTHC, while increases the amount of CO2 (idle state). Thisis attributed to the fact that the vehicle emission levelsare quite low and the noble metal catalyst required for theTHC emissions would easy remove most of the CO under
these lean conditions. Furthermore, the catalyticconverter is more effective in MPI-gasoline than those forthe other two injection systems (transient state).4- It is hope that the results in this study can help toadopt and developed Cairo driving cycle, which is morerealistic to represent Cairo traffic conditions, and can beused for tests of vehicles running in Cairo in future inorder to report the real world performance of vehicles in
8/4/2019 Benazir Or
http://slidepdf.com/reader/full/benazir-or 6/11
service. Thus providing information for Egyptian's energyand environmental ministry on how to set up propernational standards for the motor vehicles fuelconsumption and exhaust emissions. It is also hoped thatthe proposed methods could be used for other big cities
as well as for other types of vehicle
ACKNOWLEDGEMENT
I pay profound greatefulness to my project guide Lecturer prof. L.K. TOKE (Mechanical
Engineering Department) whose guidance & constant motivation led me towards thesucceeful completion of the seminar work . I acknowledge with a deep sense of gratitude,
the encouragement received from them .
Last but not the least I would like to thank all the staff members (Mechanical
Department ) & my friends who helped me directly or indirectly for the successful