Top Banner
Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations on your purchase of the Bee*R Rev Limiter! Please use the following instructions to properly install your Bee*R product.
13

Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Feb 29, 2020

Download

Documents

dariahiddleston
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

Bee*R Ignition Rev Limiter Fitting (English Instructions)

Congratulations on your purchase of the Bee*R Rev Limiter! Please use the following

instructions to properly install your Bee*R product.

Page 2: Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

Please read this literature in its entirety before you start to perform the installation to

ensure that you get the job done correctly and safely.

It is strongly recommended that you have a certified automotive electrician to perform

the installation of this product.

Before going any further, please note:

***NOTE***

These instructions are for the Type B rev limiters. For Honda applications please use

Type H or H2 rev limiters.

Safety:

A. For safe use, read, understand and consent to the safety notes.

B. Only install when the vehicle’s engine condition, performance and problems are

well known.

C. It not recommended using this product on a car that is not listed in the noted

vehicle applications. This also goes for cars that do have a listed application but has a

different engine not listed in the noted vehicle applications.

D. Please acknowledge that problems that may occur due to improper installation,

improper use, not fully understanding the instruction manual, or other unstated

problem(s) as a result of installing this product is not the responsibility of Bee*R or

Bee*R authorized agents in any way, form or fashion.

E. This product is an accessory used to improve performance, and it must be used

accordingly (please see note D).

F. Due to the nature of racing and the use of the product, all sales are final and the

end-user accepts all risks involved in using this product. All returns must be

authorized and inspected by Bee*R in any case where bad craftsmanship is suspected.

We do this due to the amount of fakes that are in production by counterfeit parties.

Just because it says Bee*R doesn’t mean it is a Bee*R product. Only Bee*R can

ascertain whether the product is genuine. Bee*R authorized agents must forward

returned Bee*R products to Bee*R and cannot make any assumptions nor take

action(s) without consent from Bee*R. If you purchased the product from an

authorized Bee*R agent, your item has already been verified as authentic and will be

returned to Bee*R for review and determination of course of action.

***WARNINGS***

A. Ignoring the WARNINGS may lead to accidental death of driver, passengers or

3rd parties.

Page 3: Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

B. Under no circumstances should the product be used in any other way than specified

in the manual.

C. The product cannot be guaranteed to perform in ways it was not intended to.

Misuse of this item may lead to engine malfunction, injury or death.

D. If strange noises or smells occurs at any time, discontinue use immediately to

prevent electric shock, fire and/or damage to electrical components.

E. Do not use this product other than what it was designed for. If used other than

designed for, loss and damage caused by or to customer and/or third parties may

occur.

F. If this product is installed in a non-stable environment, this product may interfere

with normal driving.

G. If the product becomes a hindrance or interferes with driving, please discontinue

use.

H. Please install only after removing negative terminal of the battery.

I. When the connector is disconnected, do not pull on the harness.

J. Do not wire together with other electrical components (shared wiring). Wiring with

other accessories may cause a short circuit or electrical fire.

K. Do not adjust product during normal driving or travelling. If used during normal

driving, the chance of accident and danger increases.

NOTES:

A. Ignoring the notes and cautions may lead to physical or fatal injury due to

dangerous handling.

B. Do not disassemble the product or modify. Doing so may lead to an electrical fire,

shock or electrical damage.

C. Do not install in an area exposed to heat or water. If exposed to heat or water,

product will malfunction and lead to possible electrical shock, fire or vehicle damage.

D. Please inspect the item regularly, and if the product appears normal, please use.

E. The product is manufactured with high quality material and strict quality standards.

Malfunction or decrease in performance may depend on the condition of the vehicle.

It is imperative that the car be properly tuned up and maintained before installing this

product.

F. This product must be installed by a qualified automotive technician, and if

questions arise please contact Bee*R directly.

Page 4: Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

G. Both the customer and installer must understand and read the manual and accept

the conditions before installing this product. Bee*R will not accept any liability or

responsibility for any damage or consequences of installing the product.

H. Please make sure that you read the instruction manual before asking any questions.

I. Use of this product is at customer consent. Bee*R is in no way responsible for

damage to vehicle, accidents or fatal injury due to improper use of this Bee*R

product. Bee*R can only warranty the craftsmanship and quality of this product. All

Bee*R products will be inspected upon return before any replacement is authorized or

given by Bee*R. This product is intended for race use only and may never be used on

the streets. All sales are final.

Let’s get going!

Page 5: Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

Page 6: Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

PART 1 (using Nissan S14 kouki as the example)

1) Disconnect the negative battery cable

2) Remove the trim covering the ECU in the passenger foot well (use the correct side

depending on your model). It is recommended that you take out the passenger seat to

give you more room to work.

Page 7: Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

3) With a 10 mm socket or wrench, disconnect the ECU plug and locate the correct

wires using the diagram below according to your vehicle specifications. You do not

have to remove the ECU unless you feel it is necessary to do so. The pins you will use

are identified in the diagram according to the engine/car type you have and are

colored to match the Bee-R wire colors. The green and yellow are already reversed

on this diagram as it seems the Bee-R diagram is wrong for most cars. When the car

is all back together and it won’t start, swap the green/ and yellow.

CA18DET (R)S13 and S14 (zenki) use diagram N01

SR20DET (R)PS13, S14 (kouki) and S15 use diagram N02

Page 8: Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

The picture below shows the wires on for N02 connection type.

***ATTENTION!***

The tools/items you will need to perform the electrical work, at a minimum are

electrical wire cutter and crimper and bullet connectors. These items can be found at

any automotive electrical store.

***CAUTION!***

Do not use electroclamps. These have been known to fail.

Page 9: Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

Cut the necessary wires one at a time. Do not rush this step.

Slip the bullet connector insulation onto the wire and strip the end about 10 mm to

expose the wiring.

Loop the exposed wiring.

Page 10: Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

Insert the bullet connection (male or female) and crimp the connection. Repeat this for

each of the wires.

Your wiring will look like this after you have completed the wiring of the Bee*R Rev

Limiter.

PART 2

1) On the controller, cut the gray wire for 4 cylinder applications.

Page 11: Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

2) The option to use REV2 setting requires the white wire to be connected in-line

with the e-brake switch. You must remove the center console to do this.

You will need a minimum of one meter of white wiring to do this option.

Page 12: Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

Now reconnect the ECU and the ECU plug.

Reconnect the negative battery cable.

3) Turn the ignition to the “ON” position and check for abnormal smells and/or

smoke. Start the car. If it won’t start, you need to swap the green and yellow wires.

Replace all the trim panels. Both the Rev 1 and Rev 2 should be at position 0. Rev

the car and it should cut at 2500rpm with the handbrake up or down. Change the

setting on Rev 1 to 2 and try again. With the handbrake up it should rev to 2500rpm,

with it down it should now be 3500rpm. Rev 2 can be used as a launch control.

Adjust Rev 1 and Rev 2 to the setting you require using the following:

0) 2500

1) 3000

2) 3500

3) 4000

4) 4500

5) 5000

6) 5500

7) 6000

8) 6500

Page 13: Bee-R Ignition Rev Limiter Fitting Guide · Translated with permission from Bee*R for Tuned Japan by Kenji Bou Bee*R Ignition Rev Limiter Fitting (English Instructions) Congratulations

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

9) 7000

A) 7500

B) 8000

C) 8500

D) 9000

E) 9500

F) 10000

REV1 is the normal rev limit and REV2 is the limit when e-brake switch is engaged.

GAIN sets the frequency and length of cut.

4) Once you are satisfied with the settings, mount the limiter using double-sided tape.

You will need to clean the surfaces the tape will be adhered to. Brake/parts cleaner is

an excellent choice to remove oil and residue.

5) DO NOT TRY TO ADJUST THE LIMITER “ON THE FLY”! You will risk

damaging your electronics. It is highly recommended that the Bee*R Rev Limiter be

adjusted in a controlled environment.

6) Enjoy!