This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
220 V AC, 60 Hz (Korean)220 – 240 V AC, 50/60 Hz (EC1, EC2, CEK, Australian, Chinese, Russian)
Jack type/Output level/Load impedance)
Saudi Arabia, Brazilian, Hong Kong, Thai)
(US, Canadian, Australian, Chinese, PX, Russian, Saudi Arabia, Hong Kong, Taiwan, Korea, Thai)
(BX2: US, Canadian/S360: E, Brazilian)
– 2 –
BDP-BX2/S357/S360/S363
SAFETY CHECK-OUT
LEAKAGE TESTThe AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods.1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these instruments.
2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A)
1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.
5. Check the line cord for cracks and abrasion. Recommend the replacement of any such line cord to the customer.
6. Check the B+ voltage to see it is at the values specified.7. Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
After correcting the original service problem, perform the following safety checks before releasing the set to the customer:
1.5 kΩ0.15 µFACvoltmeter(0.75 V)
To Exposed MetalParts on Set
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
Unleaded solderBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder. Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to
about 350°C. Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!• Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.
• Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
CAUTION:The use of optical instrument with this product will increase eye hazard.
CAUTIONUse of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radia-tion exposure.
This label is located on the laser protective housing inside the enclosure.
WARNING!!WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 25 cm FROM THE SURFACE OF THE OBJEC-TIVE LENS ON THE OPTICAL PICK-UP BLOCK.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK OR DOTTED LINE WITH MARK ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. RE-PLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉ-MENTS PUBLIÉS PAR SONY.
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the laser protective housing inside the enclosure. (EC1, EC2, CEK, Australian, Chinese, Russian, Saudi Arabia, Hong Kong, Taiwan, Korea, Thai)
– 3 –
BDP-BX2/S357/S360/S363
TABLE OF CONTENTS
Section Title Page Section Title Page
1. SERVICE NOTE
1-1. Disc Removal Procedure If The Tray Cannot Be Ejected (Forced Ejection) ............................................. 1-11-2. Work when optical device are replaced ........................ 1-11-3. Test Disc ....................................................................... 1-2 1-3-1. Operation and Display ............................................. 1-21-4. Drive Repairing............................................................. 1-15 1-4-1. Preparation .............................................................. 1-15 1-4-2. Checking Flow ~ Drive (BU) section ~ .................... 1-15 1-4-3. BU Check Flow [zz] ~ .............................................. 1-16 1-4-4. BU (Optical Block) Repair Guide ............................. 1-16 1-4-5. BU Adjustment Flow [yy] ~ ...................................... 1-17 1-4-6. KEM-430AAA/C2RP Packing Spec. ....................... 1-17 1-4-7. KEM-430AAA/C2RP Folding Motor FFC ................ 1-18 1-4-8. KEM-430AAA/C2RP Packing .................................. 1-18 1-4-9. BU Data Decode Jig ................................................ 1-19 1-4-10. Loading For Service ................................................ 1-19 1-4-11. Laser Caution Label ................................................ 1-20 1-4-12. Useful service mode function .................................. 1-201-5. BU Service Policy ......................................................... 1-21
10-1. Exploded Views ............................................................ 10-1 10-1-1. Case Section ........................................................... 10-1 10-1-2. Front/Rear Chassis Section .................................... 10-2 10-1-3. Main Chassis Section .............................................. 10-3 10-1-4. BD Section .............................................................. 10-4 10-1-5. Accessories ............................................................. 10-510-2. Electrical Parts List ....................................................... 10-6
1-1
BDP-BX2/S357/S360/S363SECTION 1
SERVICE NOTE
1-1. DISC REMOVAL PROCEDURE IF THE TRAY CANNOT BE EJECTED (FORCED EJECTION)
1. Remove the upper case. (Refer to page 2-1)2. Insert a clip in the hole of a drive and open a tray. Note: Use a clip of about 1.2 mm in the diameter
1-2. Work when optical device are replaced
Note: Please do the following work when you replace the optical device.
1. Install it in PC after downloading two set of software from following URL. (Refer to “1-4-9. BU Data Decode Jig” on page 1-19)
STEP 1 Microsoft .NET Framework Version 2.0 Redistributable Package (x86) http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=0856eacb-4362-4b0d-8edd-aab15c5e04f5
STEP 2 Microsoft .NET Framework 2.0 Service Pack 1 (x86) http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=79bc3b77-e02c-4ad3-aacf-a7633f706ba5
2. Take the photograph the part of the bar code of the optical device. (Refer to the following picture)
3. Drag-and-drop the bar code photograph to the icon of decode software (BDBUDec). * The decode software is a complete set of “BDBUDec”, “Tasman.Bars.dll”, and “SavePath”. * Because docode software cannot be attached, it separately distributes it.
4. Input the password when you start decode software.* Inquire of each service headquarters because the password cannot be disclosed.
5. Write the decode data to the set. (Refer to “1-4-4. BU (Optical Block) Repair Guide” on page 1-16 and “1-4-5. BU Adjustment Flow [yy]” on page 1-17)
tray
clip(Use that of about 1.2 mm in the diameter)
hole
1-2
BDP-BX2/S357/S360/S363
1-3. TEST DISC
Part No. Description LayerJ-6090-199-A BLX-104 Single Layer
J-6090-200-A BLX-204 Dual Layer
J-2501-307-A CD (HLX-A1)
J-2501-305-A HLX-513 Single Layer (NTSC)
J-2501-306-A HLX-514 Dual Layer (NTSC)
J-6090-077-A HLX-506 Single Layer (PAL)
J-6090-078-A HLX-507 Dual Layer (PAL)
1-3-1. Operation and Display
Check Items1) BLX-104 1. Select 23.976Hz/1080p 2. Play “4.Motion pictures” 3. Check whether player can play back or not 4. Check each outputs Video: Composite/S Video/component/HDMI Audio: Digital out (Coaxial/Optical)/Audio out/5.1Ch output* When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz) can use instead of 1080/24p. However this is temporary correspondence.
2) BLX-204 1. Select 1080i (59.94Hz or 50Hz) 2. Play “4.Motion pictures” 3. Check whether player can play back or not (Check the picture and sound output)
3) CD (HLX-A1) Check whether player can play back or not (Check the sound output)
4) HLX-513/514 (NTSC), HLX-506/507 (PAL) 1. After displayed Main Menu, select “1.Video” 2. Play “1.Color Bar 100%” (Check the picture and sound output) 3. Return to Menu 4. Play “Demonstration 4:3” or “5.Demonstration 16:9” (Check the picture and sound output)
1-3
BDP-BX2/S357/S360/S363
1-3-1-1. BLX-104 Menu Function (1)Main Menu
X
X
X
X
X
X
X
X
X
X X X
X X X
X
1) When the disc is inserted, 1. Video Signal of 59.94Hz/1080i of the Main Menu is selectively displayed.
1-3-1-2. BLX-104 Menu Function (2)Main Menu
Sub_menu1 is displayedTo Main Menu after playback from T2_C1 to T19_C1To Main Menu after playback of T20_C1To Main Menu after playback of T21_C1
Sub_menu3 is displayedTo Main Menu after playback from T54_C1 to T60_C1To Main Menu after playback of T61_C1To Main Menu after playback of T62_C1
* When returning to Main Menu after playback from each button of 59.94Hz/1080i, 1. Video Signal of 59.94Hz/1080i is selectively dis-played.
* When returning to Main Menu after playback from each button of 50Hz/1080i, 1. Video Signal of 50Hz/1080i is selectively displayed.* 5. AV Sync does not operate.Note: Txx_ Cxx Chapter No. Title No.
1-4
BDP-BX2/S357/S360/S363
1-3-1-3. BLX-104 Menu Function (3)Main Menu
To Main Menu after playback from T23_C1 to T40_C1To Main Menu after playback of T41_C1To Main Menu after playback of T42_C1
Sub_menu2 is displayedTo Main Menu after playback from T44_C1 to T50_C1To Main Menu after playback of T51_C1To Main Menu after playback of T52_C1
Sub_menu4 is displayed
* When returning to Main Menu after playback from each button of 59.94Hz/720P, 1. Video Signal of 59.94Hz/720P is selectively dis-played.
* When returning to Main Menu after playback from each button of 23.976Hz/1080P, 1. Video Signal of 23.976Hz/1080P is selectively displayed.
* 5. AV Sync does not operate.
1-5
BDP-BX2/S357/S360/S363
1-3-1-4. BLX-104 Menu Function (4)Sub menu1
X
X
X
X
X
X
1) At the display of Sub menu1, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu1 after seamless playback from T1_C1 to T1_C13. 1. Color Bar 100% is selec-
tively displayed on Sub menu1 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu1 after seamless playback from T1_C2 to T1_C13. 1. Color Bar 100% is selectively
displayed on Sub menu1 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu1, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/1080i
is selectively displayed.6) Selection of LPCM Audio t Playback from T2_C1 to T19_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen.7) Selection of Dolby AC-3 Audio t Playback of T20_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen.8) Selection of Motion Picture t Return to Sub menu1 after playback of T21_C1. 1. ColorBar 100% is selectively displayed on Sub
menu1 screen.9) At the selection of Main Menu, 1. VideoSignal of 1080/59.94i of Main Menu is selectively displayed.10) AV Sync does not operate.
1-6
BDP-BX2/S357/S360/S363
1-3-1-5. BLX-104 Menu Function (5)Sub menu2
X
X
X
X
X
X
1) At the display of Sub menu2, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu2 after seamless playback from T43_C1 to T43_C13. 1. Color Bar 100% is
selectively displayed on Sub menu2 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu2 after seamless playback from T43_C2 to T43_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu2 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu2, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of
23.976Hz/1080P is selectively displayed.6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen.7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen.8) Selection of Motion Picture t Return to Sub menu2 after playback of T52_C1. 1. Color Bar 100% is selectively displayed on Sub
menu2 screen.9) At the selection of Main Menu, 1. Video Signal of 1080/23.976P of Main Menu is selectively displayed.10) AV Sync does not operate.
1-7
BDP-BX2/S357/S360/S363
1-3-1-6. BLX-104 Menu Function (6)Sub menu3
X
X
X
X
X
X
1) At the display of Sub menu3, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu3 after seamless playback from T53_C1 to T53_C13. 1. Color Bar 100% is
selectively displayed on Sub menu3 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu3 after seamless playback from T53_C2 to T53_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu3 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu3, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 50Hz/1080i
is selectively displayed.6) Selection of LPCM Audio t Playback from T54_C1 to T60_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen.7) Selection of Dolby AC-3 Audio t Playback of T61_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen.8) Selection of Motion Picture t Return to Sub menu3 after playback of T62_C1. 1. Color Bar 100% is selectively displayed on Sub
menu3 screen.9) At the selection of Main Menu, 1. Video Signal of 1080/50i of Main Menu is selectively displayed.10) AV Sync does not operate.
1-8
BDP-BX2/S357/S360/S363
1-3-1-7. BLX-104 Menu Function (7)Sub menu4
X
X
X
X
X
X
1) At the display of Sub menu4, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu4 after seamless playback from T22_C1 to T22_C13. 1. Color Bar 100% is
selectively displayed on Sub menu4 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu4 after seamless playback from T22_C2 to T22_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu4 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu4, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/720P
is selectively displayed.6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen.7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen.8) Selection of Motion Picture t Return to Sub menu4 after playback of T52_C1. 1. Color Bar 100% is selectively displayed on Sub
menu4 screen.9) At the selection of Main Menu, 1. Video Signal of 720/59.94P of Main Menu is selectively displayed.10) AV Sync does not operate.
1-9
BDP-BX2/S357/S360/S363
1-3-2-1. BLX-204 Menu Function (1)Main Menu
X
X
X
X
X
X
XX
X
X X X X
X X
X
X
X
1) When the disc is inserted, 1. Video Signal of 59.94Hz/1080i of the Main Menu is selectively displayed.
1-3-2-2. BLX-204 Menu Function (2)Main Menu
Sub_menu1 is displayedTo Main Menu after playback from T2_C1 to T19_C1To Main Menu after playback of T20_C1To Main Menu after playback of T21tT63tT64tT65tT66
Sub_menu3 is displayedTo Main Menu after playback of T54_C1-T60_C1tT83_C1-T94_C1To Main Menu after playback of T61_C1To Main Menu after playback of T62tT82
To Main Menu after playback of T67_C1
To Main Menu after playback of T83_C1
* When returning to Main Menu after playback from each button of 59.94Hz/1080i, 1. Video Signal of 59.94Hz/1080i is selectively dis-played.
* When returning to Main Menu after playback from each button of 50Hz/1080i, 1. Video Signal of 50Hz/1080i is selectively displayed.Note: Txx_ Cxx Chapter No. Title No.
1-10
BDP-BX2/S357/S360/S363
1-3-2-3. BLX-204 Menu Function (3)Main Menu
Sub_menu4 is displayedTo Main Menu after playback from T23_C1 to T40_C1To Main Menu after playback of T41_C1To Main Menu after playback of T42_C1
Sub_menu2 is displayedTo Main Menu after playback of T44_C1-T50_C1tT71_C1-T81_C1To Main Menu after playback of T51_C1To Main Menu after playback of T52_C1tT69
To Main Menu after playback of T68_C1
To Main Menu after playback of T70_C1
* When returning to Main Menu after playback from each button of 59.94Hz/720P, 1. Video Signal of 59.94Hz/720P is selectively dis-played.
* When returning to Main Menu after playback from each button of 23.976Hz/1080P, 1. Video Signal of 23.976Hz/1080P is selectively displayed.
1-11
BDP-BX2/S357/S360/S363
1-3-2-4. BLX-204 Menu Function (4)Sub menu 1
X
X
X
X
X
X
1) At the display of Sub menu1, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu1 after seamless playback from T1_C1 to T1_C13. 1. Color Bar 100% is selec-
tively displayed on Sub menu1 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu1 after seamless playback from T1_C2 to T1_C13. 1. Color Bar 100% is selectively
displayed on Sub menu1 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu1, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of
59.94Hz/1080i is selectively displayed.6) Selection of LPCM Audio t Playback from T2_C1 to T19_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen.7) Selection of Dolby AC-3 Audio t Playback of T20_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen.8) Selection of Motion Picture t Return to Sub menu1 after playback of T21_C1. 1. Color Bar 100% is selectively displayed on Sub
menu1 screen.9) Selection of AV Sync t Return to Sub menu1 after playback of T67_C1. 1. Color Bar 100% is selectively displayed on Sub menu1
screen.10) At the selection of Main Menu, 1. Video Signal of 1080/59.94i of Main Menu is selectively displayed.
1-12
BDP-BX2/S357/S360/S363
1-3-2-5. BLX-204 Menu Function (5)Sub menu 2
X
X
X
X
X
X
1) At the display of Sub menu2, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu2 after seamless playback from T43_C1 to T43_C13. 1. Color Bar 100% is
selectively displayed on Sub menu2 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu2 after seamless playback from T43_C2 to T43_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu2 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu2, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of
23.976Hz/1080P is selectively displayed.6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1 and from T71_C1 to T81_C1. SubPic that corresponds to Audio stream
1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen.7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen.8) Selection of Motion Picture t Return to Sub menu2 after playback of T52_C1 and T69. 1. Color Bar 100% is selectively displayed on
Sub menu2 screen.9) Selection of AV Sync t Return to Sub menu2 after playback of T70_C1. 1. Color Bar 100% is selectively displayed on Sub menu2
screen.10) At the selection of Main Menu, 1. Video Signal of 1080/23.976P of Main Menu is selectively displayed.
1-13
BDP-BX2/S357/S360/S363
1-3-2-6. BLX-204 Menu Function (6)Sub menu 3
X
X
X
X
X
X
1) At the display of Sub menu3, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu3 after seamless playback from T53_C1 to T53_C13. 1. Color Bar 100% is
selectively displayed on Sub menu3 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu3 after seamless playback from T53_C2 to T53_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu3 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu3, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 50Hz/1080i
is selectively displayed.6) Selection of LPCM Audio t Playback from T54_C1 to T60_C1 and from T84_C1 to T94_C1. SubPic that corresponds to Audio stream
1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen.7) Selection of Dolby AC-3 Audio t Playback of T61_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen.8) Selection of Motion Picture t Return to Sub menu3 after playback of T62_C1 and T82. 1. Color Bar 100% is selectively displayed on
Sub menu3 screen.9) Selection of AV Sync t Return to Sub menu3 after playback of T83_C1. 1. Color Bar 100% is selectively displayed on Sub menu3
screen.10) At the selection of Main Menu, 1. Video Signal of 1080/50i of Main Menu is selectively displayed.
1-14
BDP-BX2/S357/S360/S363
1-3-2-7. BLX-204 Menu Function (7)Sub menu 4
X
X
X
X
X
X
1) At the display of Sub menu4, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu4 after seamless playback from T22_C1 to T22_C13. 1. Color Bar 100% is
selectively displayed on Sub menu4 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu4 after seamless playback from T22_C2 to T22_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu4 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu4, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/720P
is selectively displayed.6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen.7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen.8) Selection of Motion Picture t Return to Sub menu4 after playback of T52_C1. 1. Color Bar 100% is selectively displayed on Sub
menu4 screen.9) Selection of AV Sync t Return to Sub menu4 after playback of T68_C1. 1. Color Bar 100% is selectively displayed on Sub menu4
screen.10) At the selection of Main Menu, 1. Video Signal of 720/59.94P of Main Menu is selectively displayed.
1-15
BDP-BX2/S357/S360/S363
1-4. DRIVE REPAIRING1-4-1. Preparation
1-4-2. Checking Flow ~ Drive (BU) section ~
• ESD Measures It is necessary to check the working space ESD condition before starting the Drive Part (BU) repairs
The ESD-resistance of BD Laser is weaker than DVD/CD Laser.
To prevent ESD destruction, please make sure the working space and human ESD.
Flow chart No.xx (other check sheet)
Yes
Check/replace the FFC cable, then check BDP-S360 operates normally.
FFC Cable(1-xxxxxxxx)
No
OK
Yes
NoCheck the Optical Block Unit (BU) by service mode . (Flowchart zz)BU Iop is OK?
Replace the BU.
Yes BDP-S360 can play the DVD/CD-disc.BDP-S360 can play the BD-disc.
No
Yes
No
BLX-104 DVD TEST DISC HLX-513CD TEST DISC HLX-A1
B
B
Check Drive Power Supply CN301 15p 12V / 12p 5V?
Check PS301,303 and 304Replace PS when open
Yes
No
Optical Block Check (Flowchart yy)
A
A
1-16
BDP-BX2/S357/S360/S363
1-4-3. BU Check Flow [zz] ~
Before BU Replacement ~
Enter the Service Mode
Select [2] DriveMenu
Select [7]DeltaIOPCheck for checking. specification
BD,DVD,CD; within 12Iop is out of specification,
replace BU to new one.
Check DriveDeviceDiag
No
Yes
Optical Block Check (Flowchart yy)
1-4-4. BU (Optical Block) Repair Guide
BDP 4G (BDP-S360) series component structure is as same as conventional DVD Players.However BD player requires precise read out functions and also secure contents Protection system.Since above requirement, it is necessary to set/adjust BU data to EEPROM.
The following cases need Adjustments;(1)Replace BU (MB is original)(2)Replace MB (BU is original)(3)Replace both BU and MB
•JIG RequirementDigital camera (recommend with macro mode)Barcode decoder (4GBUJIG) installed in JIG PC’sUSB memory ESD work bench
•Procedure (all cases) Refer the diagram
Remarks: The servo adjustment procedure will be carried out during OP data Writing.There is no manual adjustment procedure. LD ON TIME history doesn’t carry over. Do not touch any optical block parts, Turn Table and during replacing. BD Laser diode is very sensitive!
1-17
BDP-BX2/S357/S360/S363
1-4-5. BU Adjustment Flow [yy] ~
1-4-6. KEM-430AAA/C2RP Packing Spec.
BU Adjustment Flow [yy] ~After BU/MB Replacement ~
Remove the defective BU from Loading Assy. Also remove the BU dumpers (4pcs)
Unpack new parts and take Barcode photo by camera
Assemble BU with dumpers to Loading Ass’y(tighten screw with 2kgf)
Decode the Barcode photo by usingBDBUDec and
save the text data to USB memory
Enter the service mode and insert USB memory to rear panel
Select [2]Drive Menu → [3]RewriteOPData
After finishing the Rewrite OP data, confirm [7] DeltaIOPcheck for
BU Laser quality.
The Iop data is within specification, turn off the power
Turn On the Power and check the playbackperformance by using CD, DVD and BD.
DVD TEST DISC HLX-513CD TEST DISC HLX-A1
BLX-104
Don’t Reuse the bag!!
Open a box
Take a corrugatedcushion out
Don’t touch the area!!
Open a bag
Open a cushion
Take BU out
KEM-430AAA/C2RP Packing Spec.
1-18
BDP-BX2/S357/S360/S363
1-4-7. KEM-430AAA/C2RP Folding Motor FFC
BU Packing Condition
Marking for fold
Stretch the bent FFC straight
Fold downFFC
KEM-430AAA/C2RP Folding Motor FFC
1-4-8. KEM-430AAA/C2RP Packing
1) Store it in Cushion Carton
2) Store it in Individual Carton
3) Store it in Master Carton
4) Master carton is sealedwith the PP tape.
Individual Carton (E430-BU-RP)
Individual Carton (E430-BU-RP)
Stick it to H.PP Tape
Shipment Label(Care Mark 3)
Antistatic Bag
InstructionManual
1Process the bend of FFC.(Do as well as the state when massproduction is packed)
2 It is necessary to fold the antistaticbag in order of A to B.(Purpose: To apply loosening to part C)
3Set the upper surface of the turntable tothe part of the φ14 hole.
Store 10 individual cartons 1 step X 2 steps= 20 individual cartons in the master carton.Master Carton (E430-BU-RP)
The side with the turned flap is alid side of the individual carton.
BDBUDec.exe ; SoftwareSavePath.ini ; decoded file destination setting file (initial destination is C:¥BuData.txt)TasmanBars.dll ; decode dllUninst.exe ; unistall BDBUDec.exe from PC
・Installations1.Unzip files to any PC Folder2.Check the attached Bar code photo click and drop onto BDBUDec.exe, the Password will
be required at first time only, no need P/W from second time.3.If there is the error message (.NET frame work requirements) please apply Microsoft .NET Framework 2.0 and 2.0 SP1 from Microsoft download site.
STEP 1Microsoft .NET Framework Version 2.0 Redistributable Package (x86)http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=0856eacb-4362-4b0d-
8edd-aab15c5e04f5
STEP 2Microsoft .NET Framework 2.0 Service Pack 1 (x86)http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=79bc3b77-e02c-4ad3-
aacf-a7633f706ba5
Remarks:Do not change the decoded file name “BuData.txt”.
Loading For Service BDP 4G Loading Ass’y service parts consists from 3 parts.
①Holder, Clamper Assy②Loading Assy③Holder FFC
Currently these parts are producing 2 venders. But the THERE IS NO COMPATIBILITY.So, please DO NOT MIX the ① and ② of Loading for service and original Loading.“Loading for service” A-1727-332-A (with Loading motor FFC)
FFC1-836-504-11
(Supplied folded)
③ Holder, FFC 4-137-203-0
(FFC Holder can be used both service parts and original
parts)
①Holder, Clamper Assy
②Loading AssyLaser Caution Label
1-20
BDP-BX2/S357/S360/S363
1-4-11. Laser Caution LabelLaser Caution Label
The Loading Ass’y service parts does not have Laser Caution Label.So that please reuse the original Laser Caution label and paste it on top of new Loading Ass’y.
Limit SampleFollowing peel off condition are acceptable
1-4-12. Useful service mode functionUseful service mode functionJitter measurementSelect DriveJTCheck for Jitter value measurement. It is better to check with customer disc to reproduce their complain (If possible)
Or check the BU damage due to abnormal customer usage (suspension bending by Lens cleaner, Foreign materials inside the optical block etc…)
1 Tray open2 set the any disc3 Tray close4 press PSN and set the measurement area address. Please refer following
address for each Format (inner to outer) CD 200000 ~ 500000DVD 200000 ~ 2200000BD 1200000 ~ 12000000
5 Jitter value should be kept within following criteria.
1932
1740
BD
1795
1643
DVD
Check disc dirty or deformation 1808Market Disc
The BU suspicious1742Reference disc
Remarks (if JT Value larger than spec.)CD
1-21
BDP-BX2/S357/S360/S363
1-5. BU SERVICE POLICY2BDP_4G_BU_Service policy
BD/DVD/CD SATA Player Drive (BPD-200)
EMMA3PBE LSI
BE
BDP3G (S350)
BD/DVD/CDBare Drive
EMMA3PFFE + BE LSI
BDP4G
BDP3G = Complete BD Drive + BE LSI
BDP4G = BD Bare Drive + FE/BE LSI
BEFE
BPD-300
FE
Sony confidential
3BDP_4G_BU_Service policy
BPD-300Bare Drive
BPD-200Complete Drive
Main Board
LU + BUSATAto MB
Sony confidential
1-22
BDP-BX2/S357/S360/S3634BDP_4G_BU_Service policy
for BPD-300KEM-410ADAnext
for BPD-200KEM-410ADA
・OP = No Change・FFC Length will change for New LU
+ Cost down Items
Sony confidential
5BDP_4G_BU_Service policy
BPD-200 BPD-300
Sony confidential
1-23
BDP-BX2/S357/S360/S363
In case of BU assy replacement:
1. OP related data for new assy is controlled by BU factory 2. All of data is recorded into a barcode label3. The label is put on the assy4. Service parts will be followed5. In service, the data should be read out from problem assy6. The read data should be saved to new assy
Fact finding:
1. The label is “DATA MATRIX” format2. The number of data is 91 words3. The method of reading and saving is required when BU and
main board are replaced.
New service method
1. All of BU data on the barcode label is shot by digital camera inorder to make a JPEG file of BU data.
2. Application software in the PC makes digital data from JPEG file.
3. The converted data is stored to USB memory.
4. The USB memory is connected to BDP 4G unit.
5. In service mode, there is a command to save the data from USB memory to board memory.
1-24
BDP-BX2/S357/S360/S363
Shoot the barcodeFormat is JEPG
Application SoftwareData convert fromJEPG TEXT
Save the TEXT data
USB device is connected to EXT USB terminal on the unit, and the TEXT data as new data is loaded to unit by service mode.
The application software will be a service jig with J parts number as service jig, and the recording media will be CD-R.
PN: J6090212ADescription: BDBUDEC
When instruction to PC, password is required.
The password will be supplied to only service HQ, and service center name, q’ty and all of software registered information should be maintained by service HQ, and Video will ask to report the registration information.
・Software Contents:BDBUDec.exe ; SoftwareSavePath.ini ; decoded file destination setting file (initial destination is C:¥BuData.txt)TasmanBars.dll ; decode dllUninst.exe ; unistall BDBUDec.exe from PC
・Installations1.Files to any PC Folder2.Check the attached Bar code photo click and drop onto BDBUDec.exe, the password willbe required at first time only, no need P/W from second time.3.If there is the error message (.NET frame work requirements) please applyMicrosoft .NET Framework 2.0 and 2.0 SP1 from Microsoft download site.
STEP 1Microsoft .NET Framework Version 2.0 Redistributable Package (x86)http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=0856eacb-4362-4b0d-8edd-aab15c5e04f5STEP 2Microsoft .NET Framework 2.0 Service Pack 1 (x86)http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=79bc3b77-e02c-4ad3-aacf-a7633f706ba5Remarks:Do not change the decoded file name “BuData.txt”.
2-1
BDP-BX2/S357/S360/S363SECTION 2
DISASSEMBLY• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
2-2. UPPER CASE
2-2. UPPER CASE(Page 2-1)
2-3. FRONT PANEL ASSY(Page 2-2)
2-4. BD DRIVE(Page 2-2)
2-5. REAR PANEL BLOCK(Page 2-3)
2-7. SWITCHING REGULATOR(Page 2-4)
2-6. MB-127 BOARD(Page 2-3)
SET
1 tapping screw(tightening torque = 5.5 to 7.5 kgf•cm)
1 tapping screw(tightening torque = 5.5 to 7.5 kgf•cm)
2 three screws(tightening torque = 5.5 to 7.5 kgf•cm)
3 upper case
2-2
BDP-BX2/S357/S360/S363
2-3. FRONT PANEL ASSY
2-4. BD DRIVE
1 seven claws
2 front panel assy
7 four screws (BV3)(tightening torque = 5.5 to 7.5 kgf•cm)
8 BD drive
1 non-halogene tape
2 harness (PM-156)(CN2)
4 flexible flat cable(CN4261)
5 flexible flat cable(CN4201)
6 flexible flat cable(CN1301)
3 harness (PM-157)(CN3)
2-3
BDP-BX2/S357/S360/S363
2-5. REAR PANEL BLOCK
2-6. MB-127 BOARD
3 three screws (BV3)(tightening torque = 5.5 to 7.5 kgf•cm)
5 screw (P3)(tightening torque = 5.5 to 7.5 kgf•cm)
6 rear panel block
1 fan harness(CN1403)
4 screw (B3)(tightening torque = 4 to 5 kgf•cm)
2 two screws(tightening torque = 5.5 to 7.5 kgf•cm)
8 six screws (BV3)(tightening torque = 5.5 to 7.5 kgf•cm)
9 MB-127 board
2 harness (PM-156)(CN301)
6 harness (PM-157)(CN801)
7 harness (UV-005)(CN602)
1 flexible flat cable (FMF-003)(CN1404)
3 flexible flat cable(CN4261)
4 flexible flat cable(CN4201)
5 flexible flat cable(CN1301)
2-4E
BDP-BX2/S357/S360/S363
2-7. SWITCHING REGULATOR
2-8. CIRCUIT BOARDS LOCATION
4 five screws (BV3)(tightening torque = 5.5 to 7.5 kgf•cm)
5 switching regulator
3 harness (PM-157)(CN3)
2 harness (PM-156)(CN2)
1 harness (PF-139)(CN1)
FR-301 board
switching regulator
FL-193 board
MB-127 board
USB-014 board
3-1
BDP-BX2/S357/S360/S363SECTION 3
BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM
OPTICALTRANSMITTER
IC801
BD DRIVEDVD
Blu-rayDRIVE
MB-127 BOARD
MOTOR DRIVE
DVD/BD RFVIDEO
AUDIO(ANALOG OUTPUT)
AUDIO(DIGITAL OUTPUT)
ETHERNET
USB
IC4201
MAIN SYSTEM CONTROL, DSP,SATA I/F, MEMORY CONTROL,A/V OUT, HDMI, ETHERNET I/F,
MAIN SYSTEM CONTROL, DSP,SATA I/F, MEMORY CONTROL,A/V OUT, HDMI, ETHERNET I/F,
USB I/F
IC101
GRD1-GRD8, GRD11, GRD12
SEG1-SEG16
Q710LED DRIVE
Q711LED DRIVE
x
CN1101
LAN (100)
EXT
S701KEY2 47
RXP
Z
S703KEY3
LED_DTLED_CK
FLD_STB
SIRCS
KEY1
KEY2
KEY346CECCEC 22
N
108
14
13
17
11
15
108
USB-014 BOARD
CN362CN602
USBDP2 V34USBDM2 W34
DPDM
D+D-
23
23
CN361
32
14
13
17
11
15
X60130MHz
2
MC-10121F1_XRST
MC-10121F1_XRST
(1/3)(SEE PAGE 3-2)
(2/3)(SEE PAGE 3-3)
1
1
2
5
6
32
RXN 31
TXP 29
TXN 28
USBXO AE35
USBXI AF35
05
(IFCON FLASH WRITTER)
D701, D708(BLU-RAY DISC INDICATOR)
3-5
BDP-BX2/S357/S360/S363
3-5. POWER BLOCK DIAGRAM (1/2)
12
7-9
3, 4
1126
15
MOTORDRIVE
IC4201
+5VREGULATOR
IC601
PS304CN301
CN101
CN1301
CN1404
DR_SW12V DR_SW12VVoVCC
+8VREGULATOR
IC1351
1FB 2EN 4
6
BUFFERIC703
Q305SWITCH
P FAIL
SWITCHINGREGULATOR
IC1404
DR_SW5V DR_SW5V
11ATA-PCONT ATA_PCONT
1P-ON KEY0
UNSW6V
10 8.0V
5.0V5V_PD
14 3.3V
HB+
CN801
1UNSW12VA
FR_6V
FLD_PCONT
IT_3.3V
UNSW6V
FLD_PCONTLED_DIM
UNSW3.3V
DR_VCC8
CN602 CN361CN362
CN702
4 4 1
1
7LED_DIM
6
VBUS
VCCBLDCONLDEN
DR_VCC15
DR_VCC33
ATA_PCONT2
USB_VBUS_PCONT
PS301 UNSW6VUNSW6V
UNSW12V UNSW12V
3, 4
12
7-9
15CN2
11
1
3, 4 PS303
PS802
UNSW12V
LxVIN1
+1.5V/+3.3VREGULATOR
IC1280
7FB 9
LDOUT 2
8
ENLDO 5
VOUT 1
VIN21
L1287
R4218
DCSW
3.3V
DCSW3.3V SW3.3V
POWER
CONTROL
MC-10121F1_SW3.3VPCONT1
PCONT2
SW5VD
PCONT3
SWVIN
SW+3.3VREGULATOR
IC311
3FB 5EN 7
2
3.3V
L303
D308
+5VREGULATOR
IC70518
CN902
1
CN1402VCC
(IFCON FLASH WRITER)
(JIG)
6
+5V POWER
VBUS
+5V
+3.3V (HDMI)
CN420118
PCONT3PCONT3
SW5VD
PCONT1
+3.3VREGULATOR
IC704
SW+5VREGULATOR
IC304
PFAIL
+3.3V (AV)+3.3V
REGULATOR
IC802
UNSW3.3VUNSW+3.3VREGULATOR
IC301
DCSW5VDCSW5V
REGULATOR
IC302
-5VREGULATOR
IC806
+3.3VREGULATOR
IC805
LINE AMPIC807
VIDEOAMP
IC808
PCONT2
DLL/HDVDD_1.05VDLL+1.05V
REGULATOR
IC307
PLL_1.05VPLL+1.05V
REGULATOR
IC308
Q306, Q309B+ SWITCH
Q808, Q809B+ SWITCH
Q805, Q807B- SWITCH
FB303
HDMI OUT
EXT
USB-014 BOARD
BDDRIVE
5
Q813, Q815B- SWITCH
UNSW-9VA PS804
RESETIC809
3CN3
1
5
3 UNSW6VA PS803
D/ACONVERTER
IC804
POWER-2(SEE PAGE 3-6)
A
POWER-2(SEE PAGE 3-6)
C
POWER-2(SEE PAGE 3-6)
B
MB-127 BOARD (1/2)
1, 2
(AC IN)
CN331
CN1
1
FL-193 BOARD
1
S331I/1
05
3-6E
BDP-BX2/S357/S360/S363
3-6. POWER BLOCK DIAGRAM (2/2)
FL DRIVER
D703-D706RECT
Q706, Q707DC/DC
CONVERTER
Q1408FAN SPEEDCONTROL
IC702
REMOTE CONTROLRECEIVER
IC701
ND701FLUORESENT
INDICATORTUBE
MAIN SYSTEM CONTROL, DSP,SATA I/F, MEMORY CONTROL,A/V OUT, HDMI, ETHERNET I/F,
USB I/F
IC101
DAOUT1VCCBLDCON
E3
SUB SYSTEMCONTROL
IC1403
PFAILPFAIL
45
PB3/SW4LDEN
E12GPIO57
USB_VBUS_PCONTF30
L701PS701CN701
FLD_PCONT
FR_6V
SW3.3
V
MC-1
0121
F1_S
W3.3
V
MC-10121F1_SW3.3V
DR_V
CC15
DDR2
_1.8V
+3.3V
(AV)
+3.3V
(HDM
I)
UNSW
3.3V
CORE
_1.05
V
DLL/H
DVDD
_1.05
V
DR_V
CC33
DR_VCC33
FB60
1
PLL_
1.05V
FB40
1
FB20
1FB
101
ETHERNETPHY
IC1101
DDR2_1.8V
DDR2SDRAM
IC104DDR2
SDRAM
IC105
16MS-FLASH
IC1245
F1, F2
VEE
LED B+
R720
D707
T701Q703, Q704B+ SWITCH
Q708, Q709B+ SWITCH
64MSDRAM
IC1251
SW5V
D
OPTICALTRANSMITTER
IC801L601
DDR2SDRAM
IC204DDR2
SDRAM
IC205
4M NORFLASHROM
IC5012G NAND
FLASHROM
IC502
KEY0KEY0
49
ATA_PCONT2ATA_PCONT2
32
FLD_PCONTFLD_PCONT
53
ATA_PCONT1ATA_PCONT
33
PCONT4PCONT4
31
PCONT3PCONT3
20
PCONT2PCONT2
21PCONT1
PCONT128
FAN_CONT0FAN_CONT0 58
7
3, 4
LED_DIM6
IT_3.3V1
FR-301 BOARD
Q301, Q302SWITCHING
Q307REGULATOR
CONTROLPCONT2
CORE
_1.05
V
DRVHV5DRV
MULTIREGULATOR
IC309
13DRVL 9VOUT 3
10
EN_PSV1
FAN_CONT0
FAN_CONT1FAN_CONT2
FAN_DET
V5FILT4
L304 L301
D301
VoutViv
FANCONTROL
IC1401
3CONT 2
ADJ 4
1CN1403
32 M1401
(FAN)
FB301
FB11
01
FB11
02
1
FL303, FL307, FL308
Q303, Q304SWITCHING
Q308REGULATOR
CONTROLPCONT4
DDR2
_1.8VDRVHV5DRV
MULTIREGULATOR
IC310
13DRVL 9VOUT 3
10
EN_PSV1
V5FILT4
L302FB302 FL304, FL305
MM
UNSW6V
UNSW12V
DCSW5V
POWER-1(SEE PAGE 3-5)
C
POWER
POWER-1(SEE PAGE 3-5)
A
CONTROL
POWER-1(SEE PAGE 3-5)
B
MB-127 BOARD (2/2)
FAN_CONT1FAN_CONT1 57
FAN_CONT2FAN_CONT2 54
FAN_DETFAN_DET1 55
05
4-1
BDP-BX2/S357/S360/S363SECTION 4
SCHEMATIC DIAGRAMS
• All capacitors are in μF unless otherwise noted. pF : μμF. 50V or less are not indicated except for electrolytics and tantalums.
• All resistors are in ohms, 1/4 W (Chip resistors : 1 /10 W) un-less otherwise specified.
kΩ=1000Ω, MΩ=1000kΩ.• % : indicates tolerance.• Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, because
it is damaged by the heat.• Constants of resistors, capacitors, ICs and etc with XX indicate
that they are not used. In such cases, the unused circuits may be indicated.• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.• : nonflammable resistor• : fusible resistor• : panel designation• f : internal component.• : adjustment for repair.• : B+ Line• : B– Line• Circled numbers refer to waveforms.• Voltages are dc between measurement point.• Readings are taken with a color-bar signals on Blu-ray disc.• Readings are taken with a digital multimeter (DC 10MΩ).• Voltage variations may be noted due to normal production toler-
ances.
Note: The components identified by mark or dotted line with mark are critical for safety.Replace only with part num-ber specified.
Note: Les composants identifiés par une marque sont critiquens pour la sécurité.Ne les remplacer que par une pièce portant le numéro spécifié.
When indicating parts by reference number, please include the board name.
• Abbreviation AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EA : Saudi Arabia model HK : Hong Kong model KR : Korea model RU : Russian model TH : Thai model TW : Taiwan model
4-1. THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
4-2
BDP-BX2/S357/S360/S363
4-2. FRAME SCHEMATIC DIAGRAM
: US, CND
: EC1, EC2, CEK, AUS, CH, RU, KR
: E, PX, EA, BR, HK, TW, TH
BD DRIVESWITCHINGREGULATOR
AC IN
MB-127 BOARD
FAN
FR-301BOARD
FL-193 BOARD
USB-014BOARD
PF-139
CN3312P
CN1
CN2
CN3
HARNESS
FMF-003FFC
CN70117P
CN140417P
CN30115P
CN42615P
CN420118P
CN130145P
CN8015P
CN3625P
CN6025P
CN14033P
PM-156HARNESS
PM-157HARNESS
UV-005HARNESS
(SRV2180UC)
(SRV2182EK)
(SRV2183WW)
18
M
9
D
E
1110 152 5
K
3
I
17
05
F
1612
C
1 1986
G
14
A
13
H
L
74
J
B
4-3
BDP-BX2/S357/S360/S363
S331
1
2
2PCN331
SWITCH
2
FL-193 BOARD31
A
B
05
SWITCHINGREGULATOR
GND
P ON
/
4-3. FL-193 BOARD (SWITCH) SCHEMATIC DIAGRAM • See page 5-2 for printed wiring board.- Ref. No.: FL-193 board; 20,000 series -
4-4
BDP-BX2/S357/S360/S363
4-4. FR-301 BOARD (FL DRIVER) SCHEMATIC DIAGRAM • See page 5-3 for printed wiring board.- Ref. No.: FR-301 board; 20,000 series -
There are a few cases that the part isn’t mounted in this model is printed on this diagram.
: Uses unleaded solder.
5-7. USB-014 BOARD (USB CONNECTOR) PRINTED WIRING BOARD - Ref. No.: USB-014 board; 20,000 series -• See page 2-4 for circuit boards location.
51
1 45 6
VDR361
CN361
CN362A
1 205
1-878-085- 11
USB-014 BOARD (SIDE A)
A
1205 1-878-085- 11
USB-014 BOARD (SIDE B)
EXT
USB-014 BOARD (SIDE B)
CN362 A-1
6-1
BDP-BX2/S357/S360/S363SECTION 6
IC PIN FUNCTION DESCRIPTION
6-1. MAIN SYSTEM CONTROL PIN FUNCTION (MB-127 BOARD IC101: MC-10121F1-207-TA1-A)Pin No. Name I/O Description
A1 VOID - This pin is not ball.A2 VOID - This pin is not ball.A3 VOID - This pin is not ball.A4 RFN2 I RF I/F RF differential signal (-) InputA5 RFP2 I RF I/F RF differential signal (+) InputA6 RFN I RF I/F RF differential signal (-) InputA7 RFP I RF I/F RF differential signal (+) InputA8 AGND - Analog GND for Drive Controller BlockA9 E I RF I/F Main Beam Signal (E) InputA10 F I RF I/F Main Beam Signal (F) InputA11 D I RF I/F Main Beam Signal (D) InputA12 A I RF I/F Main Beam Signal (A) InputA13 CAGC1 I/O RF I/F Connection to condenser for AGC detector (normal)A14 CAGC2 I/O RF I/F Connection to condenser for AGC detector (for CAPA)A15 ADIN0/RFP7 I RF I/F A/D Input/GPIO 7A16 MON1/RFP4 I/O RF I/F Internal Signal Monitor, Monitor Input Signal/GPIO 4A17 RFEQOP O RF I/F RFEQ (+) Output (for monitor)A18 SAGNDANA - Analog ground for Serial ATAA19 SACREFN I Serial ATA Reference Clock Negative InputA20 SAGNDDIG - Digital ground for Serial ATAA21 SATXN0 O Serial ATA Serial Transmit Data0A22 SAGNDDIG - Digital ground for Serial ATAA23 SARXP0 I Serial ATA Serial Receive Data0A24 SAGNDDIG - Digital ground for Serial ATAA25 GND - Ground for digital and DDR2 SDRAMA26 GPIO35 I/O Horizontal Sync Signal/Composite Sync SignalA27 GND - Ground for digital and DDR2 SDRAMA28 GPIO43 I/O VODY6: Digital Video Y Data OutputA29 GND - Ground for digital and DDR2 SDRAMA30 N.U. I Not used (Fixed at "L")A31 GND - Ground for digital and DDR2 SDRAMA32 N.U. I Not used (Fixed at "H")A33 VOID - This pin is not ball.A34 VOID - This pin is not ball.A35 VOID - This pin is not ball.B1 VOID - This pin is not ball.B2 VOID - This pin is not ball.B3 AGND - Analog GND for Drive Controller BlockB4 AGND - Analog GND for Drive Controller BlockB5 AVDD33 - Analog 3.3V supply for Drive Controller BlockB6 CREG O RF I/F Regulator Voltage Output (1.65V)B7 VREFIO I/O RF I/F Reference Voltage Input/Output for pickupB8 RFTSTIN1 I RF I/F RF Test InputB9 G/FOP I RF I/F Main Beam Signal (G) Input/FO (+) Input for focusingB10 H/FOM I RF I/F Main Beam Signal (H) Input/FO (-) Input for focusingB11 B I RF I/F Main Beam Signal (B) InputB12 C I RF I/F Main Beam Signal (C) InputB13 CEQ I/O RF I/F Connection to condenser for RF EQ fc control circuitB14 REQ I/O RF I/F Connection to resistor for setting RF EQ circuit currentB15 ADIN1 I RF I/F A/D InputB16 MON2/RFP5 I/O RF I/F Internal Signal Monitor, Monitor Input Signal/GPIO 5B17 RFEQOM O RF I/F RFEQ (-) Output (for monitor)B18 SAVDDANA - 1.8V supply (Serial ATA analog VDD)B19 SACREFP I Serial ATA Reference Clock Positive InputB20 SAGNDDIG - Digital ground for Serial ATAB21 SATXP0 O Serial ATA Serial Transmit Data0B22 SAGNDDIG - Digital ground for Serial ATAB23 SARXN0 I Serial ATA Serial Receive Data0B24 SAGNDDIG - Digital ground for Serial ATA
6-2
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionB25 GPIO40 I/O VODY3: Digital Video Y Data OutputB26 GPIO42 I/O VODY5: Digital Video Y Data OutputB27 GPIO45 I/O VODY8: Digital Video Y Data OutputB28 GPIO46 I/O VODY9: Digital Video Y Data OutputB29 N.U. I/O Not usedB30 N.U. I Not used (Fixed at "H")B31 N.U. O Not usedB32 N.U. I Not used (Fixed at "H")B33 S2CSB I Clocked Serial I/F 2 Slave Select InputB34 VOID - This pin is not ball.B35 VOID - This pin is not ball.C1 VOID - This pin is not ball.C2 SDRV2 O Motor Drive I/F Thread Drive OutputC3 AVDD33 - Analog 3.3V supply for Drive Controller BlockC4 FPDVINP2 I RF I/F Front Monitor Input (+)C5 FPDVINP I RF I/F Front Monitor Input (+)C6 AGND - Analog GND for Drive Controller BlockC7 AGND - Analog GND for Drive Controller BlockC8 AVDD15 - Analog 1.5V supply for Drive Controller BlockC9 AVDD33 - Analog 3.3V supply for Drive Controller BlockC10 AVDD15 - Analog 1.5V supply for Drive Controller BlockC11 AGND - Analog GND for Drive Controller BlockC12 VDD15RVAD - Power Supply 1.5V for RV ADCC13 AVDD15 - Analog 1.5V supply for Drive Controller BlockC14 AGND - Analog GND for Drive Controller BlockC15 MON3/RFP6 I/O RF I/F Internal Signal Monitor, Monitor Input Signal/GPIO 6C16 MA4 O External SDRAM I/F Memory Address OutputC17 DVDD33 - Digital 3.3V supply for Drive Controller Block)C18 DGND - Digital GND for Drive Controller BlockC19 SAGNDDIG - Digital ground for Serial ATAC20 SAGNDDIG - Digital ground for Serial ATAC21 SAGNDDIG - Digital ground for Serial ATAC22 SAGNDDIG - Digital ground for Serial ATAC23 SAGNDDIG - Digital ground for Serial ATAC24 GPIO41 I/O VODY4: Digital Video Y Data OutputC25 GPIO50 I/O VODC3: Digital Video Cb/Cr Data OutputC26 GPIO51 I/O VODC4: Digital Video Cb/Cr Data OutputC27 VDD3 - 3.3V supply (I/O buffers)C28 GND - Ground for digital and DDR2 SDRAMC29 VDD3 - 3.3V supply (I/O buffers)C30 ATX O Sample data output for S/PDIF, HDMIC31 VDD3 - 3.3V supply (I/O buffers)C32 S2CKIN I Clocked Serial I/F 2 Serial Clock InputC33 S2DOUT O Clocked Serial I/F 2 Serial Data OutputC34 S2DIN I Clocked Serial I/F 2 Serial Data InputC35 VOID - This pin is not ball.D1 MDRV O Motor Drive I/F Spindle Drive OutputD2 SDRV1 O Motor Drive I/F Thread Drive OutputD3 DAOUT2 O RF I/F General-purpose D/A Converter OutputD4 FPDVINN2 I RF I/F Front Monitor Input (-)D5 FPDVINN I RF I/F Front Monitor Input (-)D6 CBC I/O RF I/F Connector to condenser for setting WOBBLE circuit (A+D) signal AGC response speedD7 RFTSTIN2 I RF I/F RF Test InputD8 REF16 O RF I/F System Reference Voltage Output (for 3.3V supply)D9 RFOP O RF I/F Read RF Output (+)D10 RFTST3/RFP3 O RF I/F RF Test/GPIO 3D11 DGND - Digital GND for Drive Controller BlockD12 PB0/SW1 I/O General Port I/F, Three values Control Output SW (default)D13 PB1/SW2 I/O General Port I/F, Three values Control Output SW (default)D14 MA1 O External SDRAM I/F Memory Address OutputD15 MA6 O External SDRAM I/F Memory Address Output
6-3
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionD16 MA0 O External SDRAM I/F Memory Address OutputD17 MA2 O External SDRAM I/F Memory Address OutputD18 MA3 O External SDRAM I/F Memory Address OutputD19 GND - Ground for digital and DDR2 SDRAMD20 SAVDDDIG - 1.05V supplyD21 SAVDDTIO - 1.8V supply (Serial ATA Tx I/O)D22 GPIO34 I/O Video Pixel ClockD23 GPIO37 I/O VODY0: Digital Video Y Data OutputD24 GPIO49 I/O VODC2: Digital Video Cb/Cr Data OutputD25 GPIO53 I/O VODC6: Digital Video Cb/Cr Data OutputD26 GND - Ground for digital and DDR2 SDRAMD27 AO0BD3 O Audio PCM Serial Data OutputD28 AO0BD0 O Audio PCM Serial Data-L/R Output/Down Mixed OutputD29 GND - Ground for digital and DDR2 SDRAMD30 AO0MCK O Audio Master Clock OutputD31 GND - Ground for digital and DDR2 SDRAMD32 N.U. I Not usedD33 S0DIN I Not usedD34 S0DOUT O Clocked Serial I/F 0 Serial Data OutputD35 S0CKOUT O Clocked Serial I/F 0 Serial Clock OutputE1 FDRV O Motor Drive I/F Focus Drive OutputE2 DAOUT0 O RF I/F General-purpose D/A Converter OutputE3 DAOUT1 O RF I/F General-purpose D/A Converter OutputE4 VDD15WBLAD - Power Supply 1.5V for WOBBLE ADCE5 GND_WBLAD - Ground for WOBBLE ADCE6 CWAGC I/O RF I/F Connection to condenser for setting WOBBLE circuit AGC response speedE7 CAD I/O RF I/F Connection to condenser for setting WOBBLE circuit (A+D) signal AGC response speedE8 REF075 O RF I/F System Reference Voltage Output (for 1.5V supply)E9 RFON O RF I/F Read RF Output (-)E10 AGCINP I RF I/F AGC Input (+)E11 DVDD33 - Digital 3.3V supply for Drive Controller Block)E12 PB3/SW4 I/O General Port I/F, Three values Control Output SW (default)E13 PB2/SW3 I/O General Port I/F, Three values Control Output SW (default)E14 MA7 O External SDRAM I/F Memory Address OutputE15 MA10 O External SDRAM I/F Memory Address OutputE16 MA8 O External SDRAM I/F Memory Address OutputE17 MA5 O External SDRAM I/F Memory Address OutputE18 GPIO7 O GPIO7E19 N.U. I/O Not usedE20 SAVDDDIG - 1.05V supplyE21 SAVDDTIO - 1.8V supply (Serial ATA Tx I/O)E22 GPIO38 I/O VODY1: Digital Video Y Data OutputE23 GPIO47 I/O VODC0: Digital Video Cb/Cr Data OutputE24 GPIO54 I/O VODC7: Digital Video Cb/Cr Data OutputE25 GND - Ground for digital and DDR2 SDRAME26 AO0BD1 O Audio PCM Serial Data-SL/SR OutputE27 AO0LRCK O Audio L/R Clock OutputE28 AO1BD O Audio PCM Serial Data-L/R Output/Down Mixed OutputE29 AO1BCK O Audio Data Clock OutputE30 GPIO10 I/O FORMAT0 (480, 1080="0" 720="1")E31 N.U. I/O Not usedE32 GND - Ground for digital and DDR2 SDRAME33 GND - Ground for digital and DDR2 SDRAME34 VDD3 - 3.3V supply (I/O buffers)E35 GND - Ground for digital and DDR2 SDRAMF1 TDRV O Motor Drive I/F Tracking Drive OutputF2 AVDD15 - Analog 1.5V supply for Drive Controller BlockF3 AVDD15 - Analog 1.5V supply for Drive Controller BlockF4 AGND - Analog GND for Drive Controller BlockF5 AGND - Analog GND for Drive Controller BlockF6 AVDD33 - Analog 3.3V supply for Drive Controller Block
6-4
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionF7 RLD O RF I/F Laser Driver Control for ReadF8 CBCO I/O RF I/F Connection to condenser for WOBBLE circuit (A+D) HPF
F9 CBHWBL/CID I/O RF I/F Connection to condenser for LPP circuit bottom hold (WOBBLE level) and ID detection circuit LPF
F10 AGCINN I RF I/F AGC Input (-)F11 DGND - Digital GND for Drive Controller BlockF12 MBA1 O External SDRAM I/F Memory Bank Address OutputF13 MA9 O External SDRAM I/F Memory Address OutputF14 MBA0 O External SDRAM I/F Memory Bank Address OutputF15 MA11 O External SDRAM I/F Memory Address OutputF16 MD8 I/O External SDRAM I/F Memory Data Input/OutputF17 MD11 I/O External SDRAM I/F Memory Data Input/OutputF18 GPIO6 I/O GPIO6F19 N.U. I/O Not usedF20 SAVDDDIG - 1.05V supplyF21 SAVDDTIO - 1.8V supply (Serial ATA Tx I/O)F22 GPIO39 I/O VODY2: Digital Video Y Data OutputF23 GPIO48 I/O VODC1: Digital Video Cb/Cr Data OutputF24 GPIO56 I/O VODC9: Digital Video Cb/Cr Data OutputF25 NMI I Not used (Fixed at "H")F26 AO0BD2 O Audio PCM Serial Data-C/LE OutputF27 AO1LRCK O Audio L/R Clock OutputF28 GND - Ground for digital and DDR2 SDRAMF29 GPIO15 O IT_GPIO1F30 GPIO57 O USB VBUS PCONT ("H": ON, "L": OFF)F31 UA0RXDB I UART 0 Receive DataF32 GND - Ground for digital and DDR2 SDRAMF33 VAY O S-Video Y or Composite CVBS Signal OutputF34 GND - Ground for digital and DDR2 SDRAMF35 VAB O Component Output either B or Pb SignalG1 DVDD33 - Digital 3.3V supply for Drive Controller Block)G2 SDCK O General Serial I/F Clock SignalG3 SDCS1B O General Serial I/F Channel #1 Select SignalG4 SDCS3B I/O General Serial I/F Channel #3 Select SignalG5 PA2 I/O General Port I/F G6 PA0 I/O General Port I/F G7 AVDD33 - Analog 3.3V supply for Drive Controller BlockG8 RFTST1/SWRF1/RFP1 O RF I/F RF Test Output/SWRF1 Output/GPIO 1G9 CADO I/O RF I/F Connection to condenser for WOBBLE circuit (B+C) HPF
G10 CBHLPP I/O RF I/F For LPP circuit bottom hold (LPP)G11 DVDD15 - Digital 1.5V supply for Drive Controller BlockG12 CASB O External SDRAM I/F Memory Column Address StrobeG13 MCKE O External SDRAM I/F SDRAM Clock EnableG14 RASB O External SDRAM I/F Memory Row Address StrobeG15 MD9 I/O External SDRAM I/F Memory Data Input/OutputG16 MD4 I/O External SDRAM I/F Memory Data Input/OutputG17 MD3 I/O External SDRAM I/F Memory Data Input/OutputG18 N.U. I/O Not usedG19 SAVDDDIG - 1.05V supplyG20 SAVDDTIO - 1.8V supply (Serial ATA Tx I/O)G21 GPIO36 I/O Vertical Sync Signal/Blanking Sync SignalG22 GPIO44 I/O VODY7: Digital Video Y Data OutputG23 GPIO52 I/O VODC5: Digital Video Cb/Cr Data OutputG24 GPIO55 I/O VODC8: Digital Video Cb/Cr Data OutputG25 VDD3 - 3.3V supply (I/O buffers)G26 AO0BCK O Audio Data Clock OutputG27 AO1MCK O Audio Master Clock OutputG28 GPIO14 I/O IP (Progressive="0" Interlace="1") (Not used)G29 GPIO12 I/O ASPECT0 (4:3="0" 16:9, 4:3LB="1")G30 UA0TXDB O UART 0 Transfer DataG31 SCL1 I/O I2C I/F 1 Serial Clock
6-5
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionG32 VDD3 - 3.3V supply (I/O buffers)G33 GND - Ground for digital and DDR2 SDRAMG34 VAR O Component Output either R or Pr SignalG35 GND - Ground for digital and DDR2 SDRAMH1 DGND - Digital GND for Drive Controller BlockH2 DVDD15 - Digital 1.5V supply for Drive Controller BlockH3 SDIO I/O General Serial I/F Input/Output DataH4 SDCS0B O General Serial I/F Channel #0 Select SignalH5 SDCS2B I/O General Serial I/F Channel #2 Select SignalH6 PA3 I/O General Port I/F H7 PA1 I/O General Port I/F H8 WALPF1 I/O Connection to condenser for WAPLLH9 RFTST2/SWRF2/RFP2 O RF I/F RF Test Output/SWRF2 Output/GPIO 2H10 CWHP I/O RF I/F Connection to condenser for WOBBLE circuit HPFH11 MD12 I/O External SDRAM I/F Memory Data Input/OutputH12 WEB O External SDRAM I/F Memory Write EnableH13 MCLKOUT O External SDRAM I/F SDRAM Clock OutputH14 MD7 I/O External SDRAM I/F Memory Data Input/OutputH15 MD6 I/O External SDRAM I/F Memory Data Input/OutputH16 GPIO20 I GPIO20H17 N.U. I/O Not usedH18 SAGNDDIG - Digital ground for Serial ATAH19 SAGNDDIG - Digital ground for Serial ATAH20 PVDD - 1.05V supply for PLLH21 PGND - Ground for PLLH22 RSTSWB I Hardware Reset (L: RESET)H23 TMODE4 I Not used (Fixed at "L")H24 TEST I Not used (Fixed at "L")H25 TMODE1 I Not used (Fixed at "L")H26 TMODE0 I Not used (Fixed at "L")H27 TMODE2 I Not used (Fixed at "L")H28 GPIO13 I/O ASPECT1 (4:3, 16:9="0" 4:3LB="1")H29 GPIO58 O GPIO58H30 SDA1 I/O I2C I/F 1 Serial DataH31 SDA0 I/O I2C I/F 0 Serial DataH32 GND - Ground for digital and DDR2 SDRAMH33 VAC O S-Video C Signal OutputH34 GND - Ground for digital and DDR2 SDRAMH35 VAG O Component Output either G or Y SignalJ1 X2 I/O Crystal Input/OutputJ2 SFSIO2 I/O Flash Memory I/F Serial Data Input/OutputJ3 SFSIO3 I/O Flash Memory I/F Serial Data Input/OutputJ4 PC0 I/O General Port I/F J5 PA7 I/O General Port I/F J6 PA6 I/O General Port I/F J7 PA4 I/O General Port I/F J8 MD15 I/O External SDRAM I/F Memory Data Input/OutputJ9 MD1 I/O External SDRAM I/F Memory Data Input/OutputJ10 MD2 I/O External SDRAM I/F Memory Data Input/OutputJ11 MD13 I/O External SDRAM I/F Memory Data Input/OutputJ12 LDQM I/O External SDRAM I/F Lower Data Mask ControlJ13 UDQM I/O External SDRAM I/F Upper Data Mask ControlJ14 MD5 I/O External SDRAM I/F Memory Data Input/OutputJ15 MD10 I/O External SDRAM I/F Memory Data Input/OutputJ16 GPIO5 I Not Used (Fixed at "H")J17 GPIO2 O Not UsedJ18 SAGNDDIG - Digital ground for Serial ATAJ19 VDD3 - 3.3V supply (I/O buffers)J20 PVDD - 1.05V supply for PLLJ21 PGND - Ground for PLLJ22 VDD3 - 3.3V supply (I/O buffers)
6-6
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionJ23 GND - Ground for digital and DDR2 SDRAMJ24 TMODE3 I Not used (Fixed at "L")J25 TMODE5 I Not used (Fixed at "L")J26 VRVDD - 1.05V supply for VR5500 PLLJ27 VRGND - Ground for VR5500 PLLJ28 GPIO11 I/O FORMAT1 (480="0" 720, 1080="1")J29 GND - Ground for digital and DDR2 SDRAMJ30 SCL0 I/O I2C I/F 0 Serial ClockJ31 GND - Ground for digital and DDR2 SDRAMJ32 VDD3 - 3.3V supply (I/O buffers)J33 GND - Ground for digital and DDR2 SDRAMJ34 HDVSS - Analog ground for HDMIJ35 HDVSS - Analog ground for HDMIK1 X1 I Crystal InputK2 PC1 I/O General Port I/FK3 SFCS0B O Flash Memory I/F Serial Memory Chip SelectK4 SFSIO0 I/O Flash Memory I/F Serial Data Input/OutputK5 PB4 I/O General Port I/FK6 DVDD15 - Digital 1.5V supply for Drive Controller BlockK7 PTEST28 O Test I/F (HIOCS16B)K8 PA5 I/O General Port I/FK9 MD0 I/O External SDRAM I/F Memory Data Input/OutputK10 VOID - This pin is not ball.K11 VOID - This pin is not ball.K12 VOID - This pin is not ball.K13 VOID - This pin is not ball.K14 VOID - This pin is not ball.K15 VOID - This pin is not ball.K16 VOID - This pin is not ball.K17 VOID - This pin is not ball.K18 VOID - This pin is not ball.K19 VOID - This pin is not ball.K20 VOID - This pin is not ball.K21 VOID - This pin is not ball.K22 VOID - This pin is not ball.K23 VOID - This pin is not ball.K24 VOID - This pin is not ball.K25 VOID - This pin is not ball.K26 VOID - This pin is not ball.K27 VDD10 - 1.05V supply (core)K28 VDD10 - 1.05V supply (core)K29 GND - Ground for digital and DDR2 SDRAMK30 GND - Ground for digital and DDR2 SDRAMK31 VDD3 - 3.3V supply (I/O buffers)K32 VACOMPYC - Compensation capacitanceK33 HDVSS - Analog ground for HDMIK34 HTXP2 O HDMI TMDS Data Output 2+K35 HTXN2 O HDMI TMDS Data Output 2-L1 DGND - Digital GND for Drive Controller BlockL2 PC2 I/O General Port I/FL3 SFSIO1 I/O Flash Memory I/F Serial Data Input/OutputL4 SFSCK O Flash Memory I/F Serial Interface Clock OutputL5 DVDD15 - Digital 1.5V supply for Drive Controller BlockL6 DGND - Digital GND for Drive Controller BlockL7 PTEST17 I/O Test I/F (DASPB)L8 PB5 I/O General Port I/FL9 MD14 I/O External SDRAM I/F Memory Data Input/OutputL10 VOID - This pin is not ball.L11 VOID - This pin is not ball.L12 VOID - This pin is not ball.L13 VOID - This pin is not ball.
6-7
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionL14 VOID - This pin is not ball.L15 VOID - This pin is not ball.L16 VOID - This pin is not ball.L17 VOID - This pin is not ball.L18 VOID - This pin is not ball.L19 VOID - This pin is not ball.L20 VOID - This pin is not ball.L21 VOID - This pin is not ball.L22 VOID - This pin is not ball.L23 VOID - This pin is not ball.L24 VOID - This pin is not ball.L25 VOID - This pin is not ball.L26 VOID - This pin is not ball.L27 GND - Ground for digital and DDR2 SDRAML28 VDD3 - 3.3V supply (I/O buffers)L29 GND - Ground for digital and DDR2 SDRAML30 VARSETYC - 680-ohm ResisterL31 VAREFRGB - Voltage Reference Input for DAC (1.32V)L32 HDVSS - Analog ground for HDMIL33 HDVSS - Analog ground for HDMIL34 HTXP1 O HDMI TMDS Data Output 1+L35 HTXN1 O HDMI TMDS Data Output 1-M1 CLK27OUT O 27MHz Clock output for XTALM2 FG I Motor Drive I/F FG Signal InputM3 PSI5 I/O General Port I/FM4 PSI3 I/O General Port I/FM5 PSI1 I/O General Port I/FM6 DVDD33 - Digital 3.3V supply for Drive Controller Block)M7 PTEST30 I/O Test I/F (PDIAGB)M8 DGND - Digital GND for Drive Controller BlockM9 VDD15OSC - Power Supply 1.5V for OscillatorM10 VOID - This pin is not ball.M11 VOID - This pin is not ball.M12 VOID - This pin is not ball.M13 VOID - This pin is not ball.M14 VOID - This pin is not ball.M15 VOID - This pin is not ball.M16 VOID - This pin is not ball.M17 VOID - This pin is not ball.M18 VOID - This pin is not ball.M19 VOID - This pin is not ball.M20 VOID - This pin is not ball.M21 VOID - This pin is not ball.M22 VOID - This pin is not ball.M23 VOID - This pin is not ball.M24 VOID - This pin is not ball.M25 VOID - This pin is not ball.M26 VOID - This pin is not ball.M27 VDD3 - 3.3V supply (I/O buffers)M28 DVDDYC - 3.3V supply (DAC Digital VDD)M29 VAREFYC - Voltage Reference Input for DAC (1.32V)M30 VARSETRGB - 470-ohm ResisterM31 GND - Ground for digital and DDR2 SDRAMM32 HVDD_IO - 3.3V supply (HDMI Tx I/O)M33 HDVSS - Analog ground for HDMIM34 HTXP0 O HDMI TMDS Data Output 0+M35 HTXN0 O HDMI TMDS Data Output 0-N1 CLK27IN I 27MHz Clock InputN2 P53 I/O General Port I/F N3 DVDD33 - Digital 3.3V supply for Drive Controller Block)N4 PSI4 I/O General Port I/F
6-8
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionN5 PSI2 I/O General Port I/FN6 PTEST01 I/O Test I/F (HDD1)N7 PTEST00 I/O Test I/F (HDD0)N8 PTEST14 I/O Test I/F (HDD14)N9 GNDOSC - Oscillator GNDN10 VOID - This pin is not ball.N11 VOID - This pin is not ball.N12 VOID - This pin is not ball.N13 PTEST18 I Test I/F (DIORB)N14 PTEST27 O Test I/F (HINTRQ)N15 PTEST22 I Test I/F (HDA0)N16 VDD10 - 1.05V supply (core)N17 PB7 I/O General Port I/FN18 VDD10 - 1.05V supply (core)N19 GND - Ground for digital and DDR2 SDRAMN20 VDD10 - 1.05V supply (core)N21 GND - Ground for digital and DDR2 SDRAMN22 VDD10 - 1.05V supply (core)N23 VDD10 - 1.05V supply (core)N24 VOID - This pin is not ball.N25 VOID - This pin is not ball.N26 VOID - This pin is not ball.N27 AVDDYC - Analog 3.3v supply for Sub Video DACsN28 AGNDYC - Analog ground for Sub Video DACsN29 VACOMPRGB - Compensation capacitanceN30 HDVDD - 1.05V supply (HDMI analog VDD)N31 HDVSS - Analog ground for HDMIN32 HVDD_IO - 3.3V supply (HDMI Tx I/O)N33 HDVSS - Analog ground for HDMIN34 HTXCP O HDMI TMDS Clock Output+N35 HTXCN O HDMI TMDS Clock Output-P1 GND - Ground for digital and DDR2 SDRAMP2 P52 I/O General Port I/FP3 P56 I/O General Port I/FP4 P57 I/O General Port I/FP5 PSI6 I/O General Port I/FP6 PSI0 I/O General Port I/FP7 PTEST12 I/O Test I/F (HDD12)P8 PTEST11 I/O Test I/F (HDD11)P9 PTEST02 I/O Test I/F (HDD2)P10 VOID - This pin is not ball.P11 VOID - This pin is not ball.P12 VOID - This pin is not ball.P13 PTEST15 I/O Test I/F (HDD15)P14 PTEST19 I Test I/F (DIOWB)P15 PTEST29 O Test I/F (IORDY)P16 VDD10 - 1.05V supply (core)P17 PB6 I/O General Port I/FP18 VDD10 - 1.05V supply (core)P19 GND - Ground for digital and DDR2 SDRAMP20 VDD10 - 1.05V supply (core)P21 GND - Ground for digital and DDR2 SDRAMP22 VDD10 - 1.05V supply (core)P23 VDD10 - 1.05V supply (core)P24 VOID - This pin is not ball.P25 VOID - This pin is not ball.P26 VOID - This pin is not ball.P27 AGNDYC - Analog ground for Sub Video DACsP28 AGNDRGB - Analog ground for Main Video DACsP29 DVDDRGB - 3.3V supply (DAC Digital VDD)P30 HDVSS - Analog ground for HDMI
6-9
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionP31 HDVDD - 1.05V supply (HDMI analog VDD)P32 HDVSS - Analog ground for HDMIP33 HDVSS - Analog ground for HDMIP34 HEXTP I HDMI Resistance Connection Terminal for Output Amplitude ControlP35 HEXTN I HDMI Resistance Connection Terminal for Output Amplitude ControlR1 XI I Crystal InputR2 P51 I/O General Port I/FR3 P54 I/O General Port I/FR4 P55 I/O General Port I/FR5 VDD3 - 3.3V supply (I/O buffers)R6 P50 I/O General Port I/FR7 PTEST10 I/O Test I/F (HDD10)R8 PTEST05 I/O Test I/F (HDD5)R9 PTEST06 I/O Test I/F (HDD6)R10 VOID - This pin is not ball.R11 VOID - This pin is not ball.R12 VOID - This pin is not ball.R13 PTEST26 O Test I/F (HDMARQ)R14 PTEST25 I Test I/F (HDMACKB)R15 PTEST23 I Test I/F (HDA1)R16 PTEST21 I Test I/F (HCS1B)R17 PTEST20 I Test I/F (HCS0B)R18 GND - Ground for digital and DDR2 SDRAMR19 GND - Ground for digital and DDR2 SDRAMR20 GND - Ground for digital and DDR2 SDRAMR21 GND - Ground for digital and DDR2 SDRAMR22 GND - Ground for digital and DDR2 SDRAMR23 GND - Ground for digital and DDR2 SDRAMR24 VOID - This pin is not ball.R25 VOID - This pin is not ball.R26 VOID - This pin is not ball.R27 AVDDRGB - Analog 3.3v supply for Main Video DACsR28 AGNDRGB - Analog ground for Main Video DACsR29 HDVSS - Analog ground for HDMIR30 HDVSS - Analog ground for HDMIR31 HDVDD - 1.05V supply (HDMI analog VDD)R32 HVDD_IO - 3.3V supply (HDMI Tx I/O)R33 HDVDD - 1.05V supply (HDMI analog VDD)R34 HDVSS - Analog ground for HDMIR35 HDVSS - Analog ground for HDMIT1 XO O Crystal OutputT2 CLKSEL I OSC27/CLK27IN Select SignalT3 GND - Ground for digital and DDR2 SDRAMT4 VDD18 - 1.8V supply (DDR2 SDRAM)T5 D0DQ9 I/O DDR2 Data Input/OutputT6 GND - Ground for digital and DDR2 SDRAMT7 VDD18 - 1.8V supply (DDR2 SDRAM)T8 PTEST08 I/O Test I/F (HDD8)T9 PTEST16 I Test I/F (HRESETB)T10 VOID - This pin is not ball.T11 VOID - This pin is not ball.T12 VOID - This pin is not ball.T13 VDD10 - 1.05V supply (core)T14 VDD10 - 1.05V supply (core)T15 PTEST03 I/O Test I/F (HDD3)T16 PTEST13 I/O Test I/F (HDD13)T17 PTEST24 I Test I/F (HDA2)T18 GND - Ground for digital and DDR2 SDRAMT19 GND - Ground for digital and DDR2 SDRAMT20 GND - Ground for digital and DDR2 SDRAMT21 GND - Ground for digital and DDR2 SDRAM
6-10
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionT22 VDD10 - 1.05V supply (core)T23 VDD10 - 1.05V supply (core)T24 VOID - This pin is not ball.T25 VOID - This pin is not ball.T26 VOID - This pin is not ball.T27 GND - Ground for digital and DDR2 SDRAMT28 GND - Ground for digital and DDR2 SDRAMT29 HDVSS - Analog ground for HDMIT30 HDVSS - Analog ground for HDMIT31 HHPD I HDMI Hot Plug DetectT32 ETMDC O Ether Management Clock OutputT33 ETMDIO I/O Ether Management Data Input/OutputT34 ETREFCLK I Ether Reference Clock InputT35 VDD3 - 3.3V supply (I/O buffers)U1 GND - Ground for digital and DDR2 SDRAMU2 GND - Ground for digital and DDR2 SDRAMU3 D0DQ10 I/O DDR2 Data Input/OutputU4 D0DM1 I/O DDR2 Data MaskU5 GND - Ground for digital and DDR2 SDRAMU6 D0DQ11 I/O DDR2 Data Input/OutputU7 D0DQ8 I/O DDR2 Data Input/OutputU8 VDD18 - 1.8V supply (DDR2 SDRAM)U9 GND - Ground for digital and DDR2 SDRAMU10 VOID - This pin is not ball.U11 VOID - This pin is not ball.U12 VOID - This pin is not ball.U13 TEST1 I Test I/FU14 PTEST07 I/O Test I/F (HDD7)U15 PTEST09 I/O Test I/F (HDD9)U16 PTEST04 I/O Test I/F (HDD4)U17 GND - Ground for digital and DDR2 SDRAMU18 GND - Ground for digital and DDR2 SDRAMU19 GND - Ground for digital and DDR2 SDRAMU20 GND - Ground for digital and DDR2 SDRAMU21 GND - Ground for digital and DDR2 SDRAMU22 GND - Ground for digital and DDR2 SDRAMU23 GND - Ground for digital and DDR2 SDRAMU24 VOID - This pin is not ball.U25 VOID - This pin is not ball.U26 VOID - This pin is not ball.U27 HDSCL I/O HDMI DDC ClockU28 HDVSS - Analog ground for HDMIU29 ETRXER I Ether RX Error DetectionU30 ETRXD0 I Ether RX Data InputU31 ETRXD1 I Ether RX Data InputU32 VDD3 - 3.3V supply (I/O buffers)U33 ETCRS I Ether RX Data EnableU34 GND - Ground for digital and DDR2 SDRAMU35 GND - Ground for digital and DDR2 SDRAMV1 D0DQS1 I/O DDR2 Positive Data StrobeV2 D0DQS1B I/O DDR2 Negative Data StrobeV3 GND - Ground for digital and DDR2 SDRAMV4 D0DQ13 I/O DDR2 Data Input/OutputV5 GND - Ground for digital and DDR2 SDRAMV6 D0DQ12 I/O DDR2 Data Input/OutputV7 D0DQ14 I/O DDR2 Data Input/OutputV8 GND - Ground for digital and DDR2 SDRAMV9 D0VDD10 - 1.05V supply (DDR2 SDRAM DLL)V10 VOID - This pin is not ball.V11 VOID - This pin is not ball.V12 VOID - This pin is not ball.
6-11
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionV13 GND - Ground for digital and DDR2 SDRAMV14 GND - Ground for digital and DDR2 SDRAMV15 GND - Ground for digital and DDR2 SDRAMV16 GND - Ground for digital and DDR2 SDRAMV17 GND - Ground for digital and DDR2 SDRAMV18 GND - Ground for digital and DDR2 SDRAMV19 GND - Ground for digital and DDR2 SDRAMV20 GND - Ground for digital and DDR2 SDRAMV21 GND - Ground for digital and DDR2 SDRAMV22 HAVDD - 3.3V supply (HDMI Analog VDD)V23 HAVSS - Analog ground for HDMIV24 VOID - This pin is not ball.V25 VOID - This pin is not ball.V26 VOID - This pin is not ball.V27 HDSDA I/O HDMI DDC DataV28 VDD10 - 1.05V supply (core)V29 VDD10 - 1.05V supply (core)V30 ETTXD1 O Ether TX Data OutputV31 ETTXD0 O Ether TX Data OutputV32 ETTXEN O Ether TX Data EnableV33 GND - Ground for digital and DDR2 SDRAMV34 USBDP2 I/O USB D+ signalV35 USBRSDP2 I/O USB Full/low speed D+ signalW1 GND - Ground for digital and DDR2 SDRAMW2 GND - Ground for digital and DDR2 SDRAMW3 D0DQ15 I/O DDR2 Data Input/OutputW4 GND - Ground for digital and DDR2 SDRAMW5 D0DQ1 I/O DDR2 Data Input/OutputW6 D0DQ3 I/O DDR2 Data Input/OutputW7 D0DQ0 I/O DDR2 Data Input/OutputW8 VDD18 - 1.8V supply (DDR2 SDRAM)W9 VDD18 - 1.8V supply (DDR2 SDRAM)W10 VOID - This pin is not ball.W11 VOID - This pin is not ball.W12 VOID - This pin is not ball.W13 PVDD - 1.05V supply for PLLW14 PGND - Ground for PLLW15 GND - Ground for digital and DDR2 SDRAMW16 GND - Ground for digital and DDR2 SDRAMW17 GND - Ground for digital and DDR2 SDRAMW18 GND - Ground for digital and DDR2 SDRAMW19 GND - Ground for digital and DDR2 SDRAMW20 GND - Ground for digital and DDR2 SDRAMW21 GND - Ground for digital and DDR2 SDRAMW22 GND - Ground for digital and DDR2 SDRAMW23 GND - Ground for digital and DDR2 SDRAMW24 VOID - This pin is not ball.W25 VOID - This pin is not ball.W26 VOID - This pin is not ball.W27 GND - Ground for digital and DDR2 SDRAMW28 GND - Ground for digital and DDR2 SDRAMW29 GND - Ground for digital and DDR2 SDRAMW30 USBOCI2 I USB Over-current statusW31 USBOCI1 I USB Over-current statusW32 GND - Ground for digital and DDR2 SDRAMW33 USBDGND - Ground for USBW34 USBDM2 I/O USB D- signalW35 USBRSDM2 I/O USB Full/low speed D- signalY1 D0CLK0B O DDR2 Negative ClockY2 D0CLK0 O DDR2 Positive ClockY3 GND - Ground for digital and DDR2 SDRAM
6-12
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionY4 D0DM0 I/O DDR2 Data MaskY5 GND - Ground for digital and DDR2 SDRAMY6 D0DQ2 I/O DDR2 Data Input/OutputY7 D0DQ5 I/O DDR2 Data Input/OutputY8 VDD18 - 1.8V supply (DDR2 SDRAM)Y9 D0VDD10 - 1.05V supply (DDR2 SDRAM DLL)Y10 VOID - This pin is not ball.Y11 VOID - This pin is not ball.Y12 VOID - This pin is not ball.Y13 PVDD - 1.05V supply for PLLY14 PGND - Ground for PLLY15 GND - Ground for digital and DDR2 SDRAMY16 GND - Ground for digital and DDR2 SDRAMY17 GND - Ground for digital and DDR2 SDRAMY18 GND - Ground for digital and DDR2 SDRAMY19 GND - Ground for digital and DDR2 SDRAMY20 GND - Ground for digital and DDR2 SDRAMY21 GND - Ground for digital and DDR2 SDRAMY22 VDD10 - 1.05V supply (core)Y23 VDD10 - 1.05V supply (core)Y24 VOID - This pin is not ball.Y25 VOID - This pin is not ball.Y26 VOID - This pin is not ball.Y27 VDD3 - 3.3V supply (I/O buffers)Y28 VDD3 - 3.3V supply (I/O buffers)Y29 VDD3 - 3.3V supply (I/O buffers)Y30 USBPPON2 O USB Power ControlY31 USBPPON1 O USB Power ControlY32 USBVDD33 - 3.3V supply for USBY33 USBVDD33 - 3.3V supply for USBY34 USBDGND - Ground for USBY35 USBDGND - Ground for USBAA1 GND - Ground for digital and DDR2 SDRAMAA2 GND - Ground for digital and DDR2 SDRAMAA3 D0DQ7 I/O DDR2 Data Input/OutputAA4 D0DQ4 I/O DDR2 Data Input/OutputAA5 VDD18 - 1.8V supply (DDR2 SDRAM)AA6 D0DQ6 I/O DDR2 Data Input/OutputAA7 D0WEB O DDR2 Command Write EnableAA8 GND - Ground for digital and DDR2 SDRAMAA9 GND - Ground for digital and DDR2 SDRAMAA10 VOID - This pin is not ball.AA11 VOID - This pin is not ball.AA12 VOID - This pin is not ball.AA13 GND - Ground for digital and DDR2 SDRAMAA14 GND - Ground for digital and DDR2 SDRAMAA15 GND - Ground for digital and DDR2 SDRAMAA16 GND - Ground for digital and DDR2 SDRAMAA17 GND - Ground for digital and DDR2 SDRAMAA18 GND - Ground for digital and DDR2 SDRAMAA19 GND - Ground for digital and DDR2 SDRAMAA20 GND - Ground for digital and DDR2 SDRAMAA21 GND - Ground for digital and DDR2 SDRAMAA22 GND - Ground for digital and DDR2 SDRAMAA23 GND - Ground for digital and DDR2 SDRAMAA24 VOID - This pin is not ball.AA25 VOID - This pin is not ball.AA26 VOID - This pin is not ball.AA27 GND - Ground for digital and DDR2 SDRAMAA28 GND - Ground for digital and DDR2 SDRAMAA29 GND - Ground for digital and DDR2 SDRAM
6-13
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionAA30 GND - Ground for digital and DDR2 SDRAMAA31 GND - Ground for digital and DDR2 SDRAMAA32 USBPVDDFIL O USB Connector for USBPGNDAA33 USBPVSS - Analog ground for USB PLLAA34 USBDP1 I/O USB D+ signalAA35 USBRSDP1 I/O USB Full/low speed D+ signalAB1 D0DQS0 I/O DDR2 Positive Data StrobeAB2 D0DQS0B I/O DDR2 Negative Data StrobeAB3 GND - Ground for digital and DDR2 SDRAMAB4 VDD18 - 1.8V supply (DDR2 SDRAM)AB5 D0CKE O DDR2 Clock EnableAB6 D0CKERSTB I DDR2 D0CKERSTB output controlAB7 D0ADD10 O DDR2 Address OutputAB8 GND - Ground for digital and DDR2 SDRAMAB9 D0VREF I DDR2 Reference VoltageAB10 VOID - This pin is not ball.AB11 VOID - This pin is not ball.AB12 VOID - This pin is not ball.AB13 VDD10 - 1.05V supply (core)AB14 VDD10 - 1.05V supply (core)AB15 GND - Ground for digital and DDR2 SDRAMAB16 PGND - Ground for PLLAB17 PGND - Ground for PLLAB18 GND - Ground for digital and DDR2 SDRAMAB19 GND - Ground for digital and DDR2 SDRAMAB20 VDD10 - 1.05V supply (core)AB21 GND - Ground for digital and DDR2 SDRAMAB22 VDD10 - 1.05V supply (core)AB23 VDD10 - 1.05V supply (core)AB24 VOID - This pin is not ball.AB25 VOID - This pin is not ball.AB26 VOID - This pin is not ball.AB27 PVDD - 1.05V supply for PLLAB28 PGND - Ground for PLLAB29 PVDD - 1.05V supply for PLLAB30 VDD10 - 1.05V supply (core)AB31 VDD3 - 3.3V supply (I/O buffers)AB32 GPIO18 I/O AOHBCK: BCK Output for External HDMI DeviceAB33 GPIO32 I/O AOHBD3: Data Output for External HDMI DeviceAB34 USBDM1 I/O USB D- signalAB35 USBRSDM1 I/O USB Full/low speed D- signalAC1 GND - Ground for digital and DDR2 SDRAMAC2 GND - Ground for digital and DDR2 SDRAMAC3 VDD18 - 1.8V supply (DDR2 SDRAM)AC4 GND - Ground for digital and DDR2 SDRAMAC5 D0ADD7 O DDR2 Address OutputAC6 D0ADD14 O DDR2 Address OutputAC7 D0ADD12 O DDR2 Address OutputAC8 GND - Ground for digital and DDR2 SDRAMAC9 GND - Ground for digital and DDR2 SDRAMAC10 VOID - This pin is not ball.AC11 VOID - This pin is not ball.AC12 VOID - This pin is not ball.AC13 VDD10 - 1.05V supply (core)AC14 VDD10 - 1.05V supply (core)AC15 GND - Ground for digital and DDR2 SDRAMAC16 PVDD - 1.05V supply for PLLAC17 PVDD - 1.05V supply for PLLAC18 GND - Ground for digital and DDR2 SDRAMAC19 GND - Ground for digital and DDR2 SDRAMAC20 VDD10 - 1.05V supply (core)
6-14
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionAC21 GND - Ground for digital and DDR2 SDRAMAC22 VDD10 - 1.05V supply (core)AC23 VDD10 - 1.05V supply (core)AC24 VOID - This pin is not ball.AC25 VOID - This pin is not ball.AC26 VOID - This pin is not ball.AC27 PGND - Ground for PLLAC28 PGND - Ground for PLLAC29 PVDD - 1.05V supply for PLLAC30 GPIO16 I/O AOHTX: IEC60958 Output for External HDMI DeviceAC31 GPIO17 I/O AOHLRCK: LRCK Clock Output for External HDMI DeviceAC32 GPIO33 I/O AOHMCK: Master Clock Output for External HDMI DeviceAC33 GPIO31 I/O AOHBD2: Data Output for External HDMI DeviceAC34 USBAVDD - Analog 3.3V supply for USBAC35 USBRREF I USB Connector for USBAGNDAD1 VDD18 - 1.8V supply (DDR2 SDRAM)AD2 VDD18 - 1.8V supply (DDR2 SDRAM)AD3 D0BA1 O DDR2 Bank AddressAD4 D0ADD1 O DDR2 Address OutputAD5 D0ADD6 O DDR2 Address OutputAD6 D0ADD4 O DDR2 Address OutputAD7 D0CASB O DDR2 Colmun Address Strobe SignalAD8 GND - Ground for digital and DDR2 SDRAMAD9 D0VDD10 - 1.05V supply (DDR2 SDRAM DLL)AD10 VOID - This pin is not ball.AD11 VOID - This pin is not ball.AD12 VOID - This pin is not ball.AD13 VOID - This pin is not ball.AD14 VOID - This pin is not ball.AD15 VOID - This pin is not ball.AD16 VOID - This pin is not ball.AD17 VOID - This pin is not ball.AD18 VOID - This pin is not ball.AD19 VOID - This pin is not ball.AD20 VOID - This pin is not ball.AD21 VOID - This pin is not ball.AD22 VOID - This pin is not ball.AD23 VOID - This pin is not ball.AD24 VOID - This pin is not ball.AD25 VOID - This pin is not ball.AD26 VOID - This pin is not ball.AD27 VDD3 - 3.3V supply (I/O buffers)AD28 VDD3 - 3.3V supply (I/O buffers)AD29 GPIO30 I/O AOHBD1: Data Output for External HDMI DeviceAD30 GPIO19 I/O AOHBD0: Data Output for External HDMI DeviceAD31 PCIRSTB I PCI I/F PCI Hardware ResetAD32 PCICLKI I PCI 33MHz Clock Input/27MHz Clock Input for System ClockAD33 GND - Ground for digital and DDR2 SDRAMAD34 USBCOM - Analog ground for USB (bulk)AD35 USBAVSS - Analog ground for USBAE1 D0BA0 O DDR2 Bank AddressAE2 D0ADD9 O DDR2 Address OutputAE3 D0ADD3 O DDR2 Address OutputAE4 D0ADD5 O DDR2 Address OutputAE5 D0ADD11 O DDR2 Address OutputAE6 D0ADD0 O DDR2 Address OutputAE7 GND - Ground for digital and DDR2 SDRAMAE8 VDD18 - 1.8V supply (DDR2 SDRAM)AE9 VDD18 - 1.8V supply (DDR2 SDRAM)AE10 VOID - This pin is not ball.AE11 VOID - This pin is not ball.
6-15
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionAE12 VOID - This pin is not ball.AE13 VOID - This pin is not ball.AE14 VOID - This pin is not ball.AE15 VOID - This pin is not ball.AE16 VOID - This pin is not ball.AE17 VOID - This pin is not ball.AE18 VOID - This pin is not ball.AE19 VOID - This pin is not ball.AE20 VOID - This pin is not ball.AE21 VOID - This pin is not ball.AE22 VOID - This pin is not ball.AE23 VOID - This pin is not ball.AE24 VOID - This pin is not ball.AE25 VOID - This pin is not ball.AE26 VOID - This pin is not ball.AE27 GND - Ground for digital and DDR2 SDRAMAE28 GND - Ground for digital and DDR2 SDRAMAE29 RDATA15/GDATA15 I/O ROM Data Input/OutputAE30 RDATA14/GDATA14 I/O ROM Data Input/OutputAE31 RDATA13/GDATA13 I/O ROM Data Input/OutputAE32 RDATA12/GDATA12 I/O ROM Data Input/OutputAE33 RDATA11/GDATA11 I/O ROM Data Input/OutputAE34 VDD3 - 3.3V supply (I/O buffers)AE35 USBXO O USB Clock output from OscillatorAF1 D0ADD13 O DDR2 Address OutputAF2 D0ADD8 O DDR2 Address OutputAF3 GND - Ground for digital and DDR2 SDRAMAF4 D0CS1B O DDR2 Chip Select/Bank AddressAF5 D0ODT1 O DDR2 On Die terminal controlAF6 GND - Ground for digital and DDR2 SDRAMAF7 D0ODT0 O DDR2 On Die terminal controlAF8 VDD18 - 1.8V supply (DDR2 SDRAM)AF9 D0VDD10 - 1.05V supply (DDR2 SDRAM DLL)AF10 VOID - This pin is not ball.AF11 VOID - This pin is not ball.AF12 VOID - This pin is not ball.AF13 VOID - This pin is not ball.AF14 VOID - This pin is not ball.AF15 VOID - This pin is not ball.AF16 VOID - This pin is not ball.AF17 VOID - This pin is not ball.AF18 VOID - This pin is not ball.AF19 VOID - This pin is not ball.AF20 VOID - This pin is not ball.AF21 VOID - This pin is not ball.AF22 VOID - This pin is not ball.AF23 VOID - This pin is not ball.AF24 VOID - This pin is not ball.AF25 VOID - This pin is not ball.AF26 VOID - This pin is not ball.AF27 VDD10 - 1.05V supply (core)AF28 VDD10 - 1.05V supply (core)AF29 RDATA10/GDATA10 I/O ROM Data Input/OutputAF30 RDATA9/GDATA9 I/O ROM Data Input/OutputAF31 RDATA8/GDATA8 I/O ROM Data Input/OutputAF32 RDATA7/GDATA7 I/O ROM Data Input/OutputAF33 RDATA6/GDATA6 I/O ROM Data Input/OutputAF34 GND - Ground for digital and DDR2 SDRAMAF35 USBXI I USB Clock input to OscillatorAG1 GND - Ground for digital and DDR2 SDRAMAG2 GND - Ground for digital and DDR2 SDRAM
6-16
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionAG3 D0ADD2 O DDR2 Address OutputAG4 D0CS0B O DDR2 Chip SelectAG5 D0RASB O DDR2 Raw Address Strobe SignalAG6 D0DQ22 I/O DDR2 Data Input/OutputAG7 D0ADD15 O DDR2 Address OutputAG8 GND - Ground for digital and DDR2 SDRAMAG9 VDD18 - 1.8V supply (DDR2 SDRAM)AG10 GND - Ground for digital and DDR2 SDRAMAG11 VDD18 - 1.8V supply (DDR2 SDRAM)AG12 GND - Ground for digital and DDR2 SDRAMAG13 D1VDD10 - 1.05V supply (DDR2 SDRAM DLL)AG14 VDD18 - 1.8V supply (DDR2 SDRAM)AG15 D1VDD10 - 1.05V supply (DDR2 SDRAM DLL)AG16 GND - Ground for digital and DDR2 SDRAMAG17 D1VREF I DDR2 Reference VoltageAG18 GND - Ground for digital and DDR2 SDRAMAG19 D1VDD10 - 1.05V supply (DDR2 SDRAM DLL)AG20 VDD18 - 1.8V supply (DDR2 SDRAM)AG21 D1VDD10 - 1.05V supply (DDR2 SDRAM DLL)AG22 GND - Ground for digital and DDR2 SDRAMAG23 VDD3 - 3.3V supply (I/O buffers)AG24 GND - Ground for digital and DDR2 SDRAMAG25 VDD10 - 1.05V supply (core)AG26 GND - Ground for digital and DDR2 SDRAMAG27 GND - Ground for digital and DDR2 SDRAMAG28 N.U. I Fixed at "H"AG29 RDATA5/GDATA5 I/O ROM Data Input/OutputAG30 RDATA4/GDATA4 I/O ROM Data Input/OutputAG31 VDD3 - 3.3V supply (I/O buffers)AG32 RDATA3/GDATA3 I/O ROM Data Input/OutputAG33 RDATA2/GDATA2 I/O ROM Data Input/OutputAG34 RDATA1/GDATA1 I/O ROM Data Input/OutputAG35 GND - Ground for digital and DDR2 SDRAMAH1 D0DQS2 I/O DDR2 Positive Data StrobeAH2 D0DQS2B I/O DDR2 Negative Data StrobeAH3 GND - Ground for digital and DDR2 SDRAMAH4 D0DQ21 I/O DDR2 Data Input/OutputAH5 D0DQ23 I/O DDR2 Data Input/OutputAH6 D0DQ20 I/O DDR2 Data Input/OutputAH7 GND - Ground for digital and DDR2 SDRAMAH8 VDD18 - 1.8V supply (DDR2 SDRAM)AH9 GND - Ground for digital and DDR2 SDRAMAH10 VDD18 - 1.8V supply (DDR2 SDRAM)AH11 GND - Ground for digital and DDR2 SDRAMAH12 VDD18 - 1.8V supply (DDR2 SDRAM)AH13 VDD18 - 1.8V supply (DDR2 SDRAM)AH14 VDD18 - 1.8V supply (DDR2 SDRAM)AH15 GND - Ground for digital and DDR2 SDRAMAH16 GND - Ground for digital and DDR2 SDRAMAH17 GND - Ground for digital and DDR2 SDRAMAH18 GND - Ground for digital and DDR2 SDRAMAH19 VDD18 - 1.8V supply (DDR2 SDRAM)AH20 VDD18 - 1.8V supply (DDR2 SDRAM)AH21 GND - Ground for digital and DDR2 SDRAMAH22 GND - Ground for digital and DDR2 SDRAMAH23 VDD3 - 3.3V supply (I/O buffers)AH24 GND - Ground for digital and DDR2 SDRAMAH25 VDD10 - 1.05V supply (core)AH26 GPIO24 O NAND_WP (L: Write Protect)AH27 GPIO26 O XAMUTE (L: MUTE)AH28 GND - Ground for digital and DDR2 SDRAM
6-17
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionAH29 RDATA0/GDATA0 I/O ROM Data Input/OutputAH30 RADD25/GADD25 O ROM Address OutputAH31 RADD24/GADD24 O ROM Address OutputAH32 GND - Ground for digital and DDR2 SDRAMAH33 RADD23/GADD23 O ROM Address OutputAH34 RADD22/GADD22 O ROM Address OutputAH35 RADD21/GADD21 O ROM Address OutputAJ1 GND - Ground for digital and DDR2 SDRAMAJ2 GND - Ground for digital and DDR2 SDRAMAJ3 D0DQ18 I/O DDR2 Data Input/OutputAJ4 D0DQ16 I/O DDR2 Data Input/OutputAJ5 D0DQ30 I/O DDR2 Data Input/OutputAJ6 D0DQ19 I/O DDR2 Data Input/OutputAJ7 VDD18 - 1.8V supply (DDR2 SDRAM)AJ8 GND - Ground for digital and DDR2 SDRAMAJ9 VDD18 - 1.8V supply (DDR2 SDRAM)AJ10 GND - Ground for digital and DDR2 SDRAMAJ11 VDD18 - 1.8V supply (DDR2 SDRAM)AJ12 GND - Ground for digital and DDR2 SDRAMAJ13 VDD18 - 1.8V supply (DDR2 SDRAM)AJ14 GND - Ground for digital and DDR2 SDRAMAJ15 D1RQ1 O DDR2 Pull up (150 ohm) to DDR2 SDRAM power supplyAJ16 D1RQ0 O DDR2 Pull down (150 ohm) to DDR2 SDRAM GNDAJ17 GND - Ground for digital and DDR2 SDRAMAJ18 VDD18 - 1.8V supply (DDR2 SDRAM)AJ19 GND - Ground for digital and DDR2 SDRAMAJ20 GND - Ground for digital and DDR2 SDRAMAJ21 VDD18 - 1.8V supply (DDR2 SDRAM)AJ22 VDD18 - 1.8V supply (DDR2 SDRAM)AJ23 GND - Ground for digital and DDR2 SDRAMAJ24 GND - Ground for digital and DDR2 SDRAMAJ25 VDD3 - 3.3V supply (I/O buffers)AJ26 GPIO25 O IT_REQ (Communication request for front micon)AJ27 GPIO28 O EMMA_CSI0_DAC2_XCS (L: Active)AJ28 GPIO23 O GLB_XRST (L: RESET)AJ29 RADD20/GADD20 O ROM Address OutputAJ30 RADD19/GADD19 O ROM Address OutputAJ31 RADD18/GADD18 O ROM Address OutputAJ32 RADD17/GADD17 O ROM Address OutputAJ33 RADD16/GADD16 O ROM Address OutputAJ34 RADD15/GADD15 O ROM Address OutputAJ35 VDD3 - 3.3V supply (I/O buffers)AK1 D0CLK1B O DDR2 Negative ClockAK2 D0CLK1 O DDR2 Positive ClockAK3 GND - Ground for digital and DDR2 SDRAMAK4 D0DM2 I/O DDR2 Data MaskAK5 D0DQ28 I/O DDR2 Data Input/OutputAK6 D0DQ17 I/O DDR2 Data Input/OutputAK7 GND - Ground for digital and DDR2 SDRAMAK8 VDD18 - 1.8V supply (DDR2 SDRAM)AK9 GND - Ground for digital and DDR2 SDRAMAK10 D1DQ24 I/O DDR2 Data Input/OutputAK11 D1DQ25 I/O DDR2 Data Input/OutputAK12 GND - Ground for digital and DDR2 SDRAMAK13 VDD18 - 1.8V supply (DDR2 SDRAM)AK14 VDD18 - 1.8V supply (DDR2 SDRAM)AK15 GND - Ground for digital and DDR2 SDRAMAK16 GND - Ground for digital and DDR2 SDRAMAK17 VDD18 - 1.8V supply (DDR2 SDRAM)AK18 D1ADD9 O DDR2 Address OutputAK19 D1ADD1 O DDR2 Address Output
6-18
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionAK20 VDD18 - 1.8V supply (DDR2 SDRAM)AK21 GND - Ground for digital and DDR2 SDRAMAK22 VDD18 - 1.8V supply (DDR2 SDRAM)AK23 VDD18 - 1.8V supply (DDR2 SDRAM)AK24 VDD18 - 1.8V supply (DDR2 SDRAM)AK25 GND - Ground for digital and DDR2 SDRAMAK26 GPIO29 O DAC_XRST (L: RESET)AK27 N.U. I Fixed at "H"AK28 GPIO27 I/O XVMUTE (Video Mute ON="0")AK29 RADD14/GADD14 O ROM Address OutputAK30 GND - Ground for digital and DDR2 SDRAMAK31 RADD13/GADD13 O ROM Address OutputAK32 RADD12/GADD12 O ROM Address OutputAK33 RADD11/GADD11 O ROM Address OutputAK34 RADD10/GADD10 O ROM Address OutputAK35 RADD9/GADD9 O ROM Address OutputAL1 GND - Ground for digital and DDR2 SDRAMAL2 GND - Ground for digital and DDR2 SDRAMAL3 D0DQ26 I/O DDR2 Data Input/OutputAL4 D0DQ24 I/O DDR2 Data Input/OutputAL5 D0DQ31 I/O DDR2 Data Input/OutputAL6 D0DQ29 I/O DDR2 Data Input/OutputAL7 VDD18 - 1.8V supply (DDR2 SDRAM)AL8 GND - Ground for digital and DDR2 SDRAMAL9 D1DQ26 I/O DDR2 Data Input/OutputAL10 D1DQ27 I/O DDR2 Data Input/OutputAL11 D1DQ31 I/O DDR2 Data Input/OutputAL12 D1DQ16 I/O DDR2 Data Input/OutputAL13 D1DQ20 I/O DDR2 Data Input/OutputAL14 D1DQ21 I/O DDR2 Data Input/OutputAL15 GND - Ground for digital and DDR2 SDRAMAL16 D1ADD4 O DDR2 Address OutputAL17 D1ADD6 O DDR2 Address OutputAL18 D1WEB O DDR2 Command Write EnableAL19 D1BA1 O DDR2 Bank AddressAL20 D1DQ1 I/O DDR2 Data Input/OutputAL21 D1DQ0 I/O DDR2 Data Input/OutputAL22 D1DQ14 I/O DDR2 Data Input/OutputAL23 D1DQ10 I/O DDR2 Data Input/OutputAL24 D1DQ11 I/O DDR2 Data Input/OutputAL25 D1DQ9 I/O DDR2 Data Input/OutputAL26 GND - Ground for digital and DDR2 SDRAMAL27 VDD3 - 3.3V supply (I/O buffers)AL28 GND - Ground for digital and DDR2 SDRAMAL29 RADD8/GADD8 O ROM Address OutputAL30 RADD7/GADD7 O ROM Address OutputAL31 VDD3 - 3.3V supply (I/O buffers)AL32 RADD6/GADD6 O ROM Address OutputAL33 RADD5/GADD5 O ROM Address OutputAL34 RADD4/GADD4 O ROM Address OutputAL35 GND - Ground for digital and DDR2 SDRAMAM1 D0DQS3 I/O DDR2 Positive Data StrobeAM2 D0DQS3B I/O DDR2 Negative Data StrobeAM3 GND - Ground for digital and DDR2 SDRAMAM4 D0DM3 I/O DDR2 Data MaskAM5 D0DQ25 I/O DDR2 Data Input/OutputAM6 VDD18 - 1.8V supply (DDR2 SDRAM)AM7 GND - Ground for digital and DDR2 SDRAMAM8 D1DQ28 I/O DDR2 Data Input/OutputAM9 D1DM3 I/O DDR2 Data MaskAM10 D1DQ18 I/O DDR2 Data Input/Output
6-19
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionAM11 D1DQ22 I/O DDR2 Data Input/OutputAM12 VDD18 - 1.8V supply (DDR2 SDRAM)AM13 D1DM2 I/O DDR2 Data MaskAM14 D1DQ23 I/O DDR2 Data Input/OutputAM15 D1CS1B O DDR2 Chip Select/Bank AddressAM16 D1ADD14 O DDR2 Address OutputAM17 D1ADD12 O DDR2 Address OutputAM18 GND - Ground for digital and DDR2 SDRAMAM19 D1CKE O DDR2 Clock EnableAM20 D1DM0 I/O DDR2 Data MaskAM21 D1DQ3 I/O DDR2 Data Input/OutputAM22 D1DQ2 I/O DDR2 Data Input/OutputAM23 VDD18 - 1.8V supply (DDR2 SDRAM)AM24 D1DQ8 I/O DDR2 Data Input/OutputAM25 D1DQ13 I/O DDR2 Data Input/OutputAM26 D1DM1 I/O DDR2 Data MaskAM27 GND - Ground for digital and DDR2 SDRAMAM28 FCSB0 O ROM Chip selectAM29 FCSB1 O ROM Chip selectAM30 FCSB2 O ROM Chip select (Not used)AM31 FCSB3 O ROM Chip select (Not used)AM32 GND - Ground for digital and DDR2 SDRAMAM33 RADD3/GADD3 O ROM Address OutputAM34 RADD2/GADD2 O ROM Address OutputAM35 RADD1/GADD1 O ROM Address OutputAN1 VOID - This pin is not ball.AN2 GND - Ground for digital and DDR2 SDRAMAN3 D0DQ27 I/O DDR2 Data Input/OutputAN4 GND - Ground for digital and DDR2 SDRAMAN5 VDD18 - 1.8V supply (DDR2 SDRAM)AN6 GND - Ground for digital and DDR2 SDRAMAN7 D1DQ30 I/O DDR2 Data Input/OutputAN8 GND - Ground for digital and DDR2 SDRAMAN9 D1DQ29 I/O DDR2 Data Input/Output
AN10 D1DQ17 I/O DDR2 Data Input/OutputAN11 VDD18 - 1.8V supply (DDR2 SDRAM)AN12 GND - Ground for digital and DDR2 SDRAMAN13 D1ADD15 O DDR2 Address OutputAN14 D1ADD2 O DDR2 Address OutputAN15 D1ADD0 O DDR2 Address OutputAN16 D1ADD7 O DDR2 Address OutputAN17 D1ADD13 O DDR2 Address OutputAN18 D1CKERSTB I DDR2 D0CKERSTB output controlAN19 GND - Ground for digital and DDR2 SDRAMAN20 D1DQ6 I/O DDR2 Data Input/OutputAN21 D1DQ4 I/O DDR2 Data Input/OutputAN22 VDD18 - 1.8V supply (DDR2 SDRAM)AN23 GND - Ground for digital and DDR2 SDRAMAN24 D1DQ12 I/O DDR2 Data Input/OutputAN25 GND - Ground for digital and DDR2 SDRAMAN26 D1DQ15 I/O DDR2 Data Input/OutputAN27 GND - Ground for digital and DDR2 SDRAMAN28 VDD18 - 1.8V supply (DDR2 SDRAM)AN29 VDD3 - 3.3V supply (I/O buffers)AN30 GRDYB I GIO I/F Ready for external device Not used)AN31 FOEB/GOEB O NOR Flash ROM Output EnableAN32 FWEB/GWEB O NOR Flash ROM Write EnableAN33 VDD3 - 3.3V supply (I/O buffers)AN34 RADD0/GADD0 O ROM Address OutputAN35 VOID - This pin is not ball.AP1 VOID - This pin is not ball.
6-20
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionAP2 VOID - This pin is not ball.AP3 GND - Ground for digital and DDR2 SDRAMAP4 D1DQS3B I/O DDR2 Negative Data StrobeAP5 GND - Ground for digital and DDR2 SDRAMAP6 D1CLK1 O DDR2 Positive ClockAP7 GND - Ground for digital and DDR2 SDRAMAP8 D1DQS2B I/O DDR2 Negative Data StrobeAP9 GND - Ground for digital and DDR2 SDRAMAP10 VDD18 - 1.8V supply (DDR2 SDRAM)AP11 GND - Ground for digital and DDR2 SDRAMAP12 D1RASB O DDR2 Raw Address Strobe SignalAP13 D1CS0B O DDR2 Chip SelectAP14 D1CASB O DDR2 Colmun Address Strobe SignalAP15 GND - Ground for digital and DDR2 SDRAMAP16 VDD18 - 1.8V supply (DDR2 SDRAM)AP17 D1ADD8 O DDR2 Address OutputAP18 D1ADD10 O DDR2 Address OutputAP19 D1ADD3 O DDR2 Address OutputAP20 GND - Ground for digital and DDR2 SDRAMAP21 VDD18 - 1.8V supply (DDR2 SDRAM)AP22 GND - Ground for digital and DDR2 SDRAMAP23 D1DQS0B I/O DDR2 Negative Data StrobeAP24 GND - Ground for digital and DDR2 SDRAMAP25 D1CLK0 O DDR2 Positive ClockAP26 GND - Ground for digital and DDR2 SDRAMAP27 D1DQS1B I/O DDR2 Negative Data StrobeAP28 GND - Ground for digital and DDR2 SDRAMAP29 VDD18 - 1.8V supply (DDR2 SDRAM)AP30 NRBB I NAND Flash ROM Ready/BusyAP31 NCLE O NAND Flash ROM Command Latch EnableAP32 GCSB0 O GIO I/F Chip selectAP33 GCSB1 O GIO I/F Chip select (Not used)AP34 VOID - This pin is not ball.AP35 VOID - This pin is not ball.AR1 VOID - This pin is not ball.AR2 VOID - This pin is not ball.AR3 VOID - This pin is not ball.AR4 D1DQS3 I/O DDR2 Positive Data StrobeAR5 GND - Ground for digital and DDR2 SDRAMAR6 D1CLK1B O DDR2 Negative ClockAR7 GND - Ground for digital and DDR2 SDRAMAR8 D1DQS2 I/O DDR2 Positive Data StrobeAR9 GND - Ground for digital and DDR2 SDRAMAR10 VDD18 - 1.8V supply (DDR2 SDRAM)AR11 D1DQ19 I/O DDR2 Data Input/OutputAR12 D1ODT0 O DDR2 On Die terminal controlAR13 D1ODT1 O DDR2 On Die terminal controlAR14 D1ADD11 O DDR2 Address OutputAR15 VDD18 - 1.8V supply (DDR2 SDRAM)AR16 GND - Ground for digital and DDR2 SDRAMAR17 D1ADD5 O DDR2 Address OutputAR18 D1BA0 O DDR2 Bank AddressAR19 D1DQ7 I/O DDR2 Data Input/OutputAR20 D1DQ5 I/O DDR2 Data Input/OutputAR21 VDD18 - 1.8V supply (DDR2 SDRAM)AR22 GND - Ground for digital and DDR2 SDRAMAR23 D1DQS0 I/O DDR2 Positive Data StrobeAR24 GND - Ground for digital and DDR2 SDRAMAR25 D1CLK0B O DDR2 Negative ClockAR26 GND - Ground for digital and DDR2 SDRAMAR27 D1DQS1 I/O DDR2 Positive Data Strobe
6-21E
BDP-BX2/S357/S360/S363
Pin No. Name I/O DescriptionAR28 GND - Ground for digital and DDR2 SDRAMAR29 VDD18 - 1.8V supply (DDR2 SDRAM)AR30 NFOEB O NAND Flash ROM Output EnableAR31 NWEB O NAND Flash ROM Write EnableAR32 NALE O NAND Flash ROM Address Latch EnableAR33 VOID - This pin is not ball.AR34 VOID - This pin is not ball.AR35 VOID - This pin is not ball.
CSI communication timeoutMainly ITcon communication error 0x01 csi_id Replace the chip corresponding to the ID, or replace the EMMA3P chip.
Cases where problem occursDevice for sending only (ex. DAC 2ch/8ch, ES DAC 2ch/8ch device)Recorded to log during a timeout of the sending complete interruptDevice for sending and receiving (ex. IFcon device)Recorded to log during a timeout of the receiving complete interruptOther VIDEO_GLUE and HDE specifications are unknown at this time.ID list (Driver/Common/CSI/if/csi_id_bdp3g_ryoushi.h)
CSI_ID_DAC_2CH = 0, / Audio DAC AK4385A 2ch Write only / CSI_ID_DAC_8CH = 1, / Audio DAC AK4358 8ch Write only / CSI_ID_DAC_2CH_ES = 2, / Audio DAC PCM1796 2ch Write only for ES / CSI_ID_DAC_8CH_ES = 3, / Audio DACs PCM1791A 2ch 4 Write only for ES / CSI_ID_VIDEO_GLUE = 4, / VIDEO Glue for ES / CSI_ID_HDE1 = 5, / HD Enhancer1 for ES / CSI_ID_HDE2 = 6, / HD Enhancer2 for ES / CSI_ID_CC_UCOM = 7, / Spare micro-controller for CC / CSI_ID_ITCON = 8, / ITcon /
I2C communication timeout 0x02 i2c_id Replace the chip corresponding to the ID, or replace the EMMA3P chip.
Cases where problem occursRecorded to log during a timeout at sending interrupt standbyID list (Driver/Common/I2C/if/i2c_id_bdp3g_ryoushi.h)
Device ID error for HDMI device 0x03 VendorId DeviceId EMMA fault/External HDMI device fault (for ES)
Read error 0x00 Check for scratches and dust on the disc. Stream or NaviPack read error. Read error for information is not handled.Wrong region 0x01 Unable to play because of wrong regionDecode error 0x02 Problem with stream This is output by detection of EMMA, and so output may continue for some time.AACS verify error 0x03 Disc may be invalid. When an error has occurred in ReqAacsPmVerifyUsageHashWrong TV system (DVD-Video) 0x04 Disc is invalid. If the TV_system is mixed in the DVD-Video disc, playback stops when mixing is found.
Drive communication error 0x00 opcode Perform key operation again. Replace if the error occurs again. EMMA error. Perform a system reboot if this occurs.Drive mechanical error 0x01 opcode Service repair Perform a system reboot if this occurs.Tray open/close error 0x02 - - - - Perform key operation again. Replace if the error occurs again. LU error: (Disc loading errorCommand timeout 0x03 Perform key operation again. Replace if the error occurs again. Immediate timeout type. Perform a system reboot if this occurs.
Shutdown due to overheating of set FAN ERR 0x01Temperature data
(8bit)Check the operating temperature environment of the set.
Cases where problem occursIf the temperature rise results in a thermal shutdown, this is recorded in the log.
No information is available yet in the conversion table between temperature data (8bit) A/D value andtemperature data.
FAN breakdown FAN ERR 0x02 Replace the fan. Cases where problem occursWhen FANDET is used, a fan breakdown diagnosis by FANDET is recorded in the log.
NAND Error E7001 0x01After rebooting, if the error occurs again, or a malfunction occurs, repair by the Service Center is needed.Replace NAND if a forced formatting of the NVRAM does not fix the problem. The settings and all other data in
the NVRAM are reset.
NAND Error E7002 0x02After rebooting, if the error occurs again, or a malfunction occurs, repair by the Service Center is needed.Replace NAND if a forced formatting of the NVRAM does not fix the problem. The settings and all other data in
the NVRAM are reset.
NAND Error E7003 0x03After rebooting, if the error occurs again, or a malfunction occurs, repair by the Service Center is needed.Replace NAND if a forced formatting of the NVRAM does not fix the problem. The settings and all other data in
the NVRAM are reset.
NAND Error E7004 0x04After rebooting, if the error occurs again, or a malfunction occurs, repair by the Service Center is needed.Replace NAND if a forced formatting of the NVRAM does not fix the problem. The settings and all other data in
the NVRAM are reset.
NAND Error E7005 0x05Reboot and perform automatic repair. If the error occurs again, repair by the Service Center is needed.Replace NAND if a forced formatting of the NVRAM does not fix the problem. The settings and all other data in
the NVRAM are reset.
NAND Error E7006 0x06Reboot and perform automatic repair. If the error occurs again, repair by the Service Center is needed.Replace NAND if a forced formatting of the NVRAM does not fix the problem. The settings and all other data in
the NVRAM are reset.
NAND Error E7007 0x07Reboot and perform automatic repair. If the error occurs again, repair by the Service Center is needed.Replace NAND if a forced formatting of the NVRAM does not fix the problem. The settings and all other data in
the NVRAM are reset.
NAND Error E7008 0x08Reboot and perform automatic repair. If the error occurs again, repair by the Service Center is needed.Replace NAND if a forced formatting of the NVRAM does not fix the problem. The settings and all other data in
the NVRAM are reset.
NAND Error E7009 0x09Reboot and perform automatic repair. If the error occurs again, repair by the Service Center is needed.Replace NAND if a forced formatting of the NVRAM does not fix the problem. The settings and all other data in
the NVRAM are reset.
NAND Error E7010 0x0AReboot and perform automatic repair. If the error occurs again, repair by the Service Center is needed.Replace NAND if a forced formatting of the NVRAM does not fix the problem. The settings and all other data in
the NVRAM are reset.
NAND Error E7011 0x0BReboot and perform automatic repair. If the error occurs again, repair by the Service Center is needed.Replace NAND if a forced formatting of the NVRAM does not fix the problem. The settings and all other data in
the NVRAM are reset.NAND (SdmRegistry) error E7101 0x65 If the error still appears after rebooting, repair by the Service Center is needed. (NAND lifespan replacementNAND (SdmRegistry) error E7102 0x66 If the error still appears after rebooting, repair by the Service Center is needed. (NAND lifespan replacementNAND (SdmRegistry) error E7103 0x67 If the error still appears after rebooting, repair by the Service Center is needed. (NAND lifespan replacementNAND (SdmRegistry) error E7104 0x68 If the error still appears after rebooting, repair by the Service Center is needed. (NAND lifespan replacementNAND (SdmRegistry) error E7105 0x69 If the error still appears after rebooting, repair by the Service Center is needed. (NAND lifespan replacement
Video filesystem mount error 0x01 Load a different disc.Photo filesystem mount error 0x02 Load a different disc.Video database mount error 0x03 Load a different disc.Photo database mount error 0x04 Load a different disc.USB mount error 0x05 Insert a USB memory device.Video unplayable 0x11 Load a different disc.Video unplayable (invalid region) 0x12 Check the product region, and load a different disc.Video unplayable (invalid tv system) 0x13 Check the product region, and load a different disc.Video unplayable (pin lock) 0x14Video unplayable (parental lock) 0x15Virtual package authentication error 0x21 Delete the BD data.Invalid disc 0x31 Load a different disc.Disc read error 0x32 Load a different disc.Buda read error 0x41 Insert a USB memory device.Buda write error 0x42 Insert a USB memory device.Ada read error 0x51 Load a different disc, and initialize the settings. There may be something wrong with the BD-J read/write, and the NAND may be corrupted.Ada write error 0x52 Load a different disc, and initialize the settings. There may be something wrong with the BD-J read/write, and the NAND may be corrupted.
ercdsense_key
cdb
Response by Service Center Additional NotesMajor ClassificationClassification Number Cause/Error Description err_info (4-byte length)
Error Information Displayed in Error LogMessage onDisplay Panel
Playback relatedERRLOG_CATEGORY_PB
DB relatedERRLOG_CATEGORY_DB
System relatedERRLOG_CATEGORY_SYSTEM
Disc, Drive, or Tray relatedERRLOG_CATEGORY_DISC
Heating relatedERRLOG_CATEGORY_THERMO
NVRAM relatedERRLOG_CATEGORY_NVRAM
0x08
0x00
0x02
0x04
0x05
0x07
9-1
BDP-BX2/S357/S360/S363SECTION 9
TROUBLESHOOTINGM
ain
Flow
char
t
No
No
Yes
Yes
No
Yes
No
Yes
No
Yes
No
No
No
Yes
Yes
Yes
No
Yes
Yes
No
Yes
No
No
Yes
Yes
No
Yes
Pow
er O
N b
y po
wer
sw
itch
on fr
ont o
r rem
ote
cont
rol.
Has
sys
tem
rese
t (E
MM
A_X
RS
T) b
een
canc
elle
d? M
easu
rem
ent p
oint
JL9
61
To V
ideo
sec
tion
flow
char
t
To IF
con
sect
ion
flow
char
t
Sta
rt (a
nd re
turn
from
eac
h flo
wch
art)
App
roxi
mat
ely
10 s
econ
ds a
fter t
he A
C is
appl
ied,
the
WA
IT d
ispl
ay fl
ashe
s se
vera
ltim
es a
nd th
e po
wer
is tu
rned
OFF
auto
mat
ical
ly.
Are
the
pow
er s
uppl
y vo
ltage
s on
the
MB
boar
d no
rmal
?To
Pow
er S
uppl
y (S
yste
m) f
low
char
t.
EN
D
Rep
lace
the
MB
boa
rd.
To D
rive
flow
char
tB
U A
djus
tmen
t Flo
w [y
y] ~
Afte
r BU
/MB
Rep
lace
men
t ~
To D
rive
flow
char
t
To F
L/FR
boa
rd fl
owch
art
Che
ck th
e pa
rts a
nd m
ount
ing
arou
nd X
401.
Rep
lace
the
MB
boa
rd.
To D
rive
flow
char
tB
U A
djus
tmen
t Flo
w [y
y] ~
Afte
r BU
/MB
Rep
lace
men
t ~
Is O
PE
N o
r CLO
SE
dis
play
ed o
n th
eflu
ores
cent
tube
?
Is th
ere
any
prob
lem
in th
e FF
C c
onne
ctio
n to
CN
4261
whi
ch c
onne
cts
the
driv
es?
To F
L/FR
boa
rd fl
owch
art
Is X
MB
or t
he S
ETU
P s
cree
n di
spla
yed
on th
evi
deo
outp
ut s
cree
n?
Do
the
up,
dow
n, le
ft, a
nd ri
ght a
rrow
key
s of
the
rem
ote
cont
rol p
erm
it op
erat
ions
on
the
XM
B?
Is th
e m
ain
cloc
k (X
401)
osc
illat
ing
prop
erly
at
27 M
Hz?
Che
ck th
e fle
xibl
e ca
ble
of th
e dr
ive.
Are
CN
1301
, CN
4201
, or C
N42
61di
scon
nect
ed?
Che
ck th
e co
nnec
tions
of t
he c
onne
ctor
s.If
ther
e is
no
impr
ovem
ent,
repl
ace
the
MB
boar
d.To
Driv
e flo
wch
art
BU
Adj
ustm
ent F
low
[yy]
~ A
fter B
U/M
BR
epla
cem
ent ~
SY
S E
RR
dis
play
app
ears
on
fluor
esce
nt tu
be.
To D
rive
flow
char
t
Is th
e so
und
repr
oduc
ed p
rope
rly w
hen
a B
D,
DV
D, o
r oth
er d
isc
is p
laye
d?To
Aud
io s
ectio
n flo
wch
art
Is th
e pi
ctur
e re
prod
uced
pro
perly
whe
n a
BD
,D
VD
, or o
ther
dis
c is
pla
yed?
To V
ideo
sec
tion
flow
char
t
Are
BD
, DV
D, o
r oth
er d
iscs
that
are
load
ed o
nth
e dr
ive
reco
gniz
ed c
orre
ctly
?
9-2
BDP-BX2/S357/S360/S363
Pow
er S
uppl
y (S
yste
m) f
low
char
t
AC
IN
Che
ck th
e ou
tput
vol
tage
s fro
m th
e po
wer
supp
ly b
lock
.A
re th
e fo
llow
ing
volta
ges
OK
?N
o
CN
301
pin
3, 4
:+12
V (U
NS
W12
V)
CN
301
pin
7, 8
, 9: +
5.8V
(UN
SW
6V)
CN
801
pin
1: +
12V
(UN
SW
12V
A)
CN
801
pin
3: +
6V (U
NS
W6V
A)
CN
801
pin
5: -9
V (U
NS
W-9
VA
)
Yes
Che
ck o
f fus
esH
ave
any
of th
e fo
llow
ing
fuse
s bl
own?
No
Rep
lace
blo
wn
fuse
s.R
epla
ce th
e M
B b
oard
if th
ere
is n
oim
prov
emen
t.
MB
boa
rd: P
S30
1, P
S30
3, P
S30
4, P
S80
2,P
S80
3, P
S80
4FR
boa
rd: P
S70
1
Yes
Che
ck th
e fo
llow
ing
pow
er c
ontro
l sig
nals
whi
le th
e po
wer
is O
N.
Are
they
H le
vel (
3.3
V)?
No
To IF
con
sect
ion
flow
char
t
PC
ON
T1: M
B b
oard
R30
4P
CO
NT2
: MB
boa
rd R
309
PC
ON
T3: M
B b
oard
R37
6P
CO
NT3
: MB
boa
rd R
367
ATA
_PC
ON
T: M
B b
oard
CN
301
pin
11A
TA_P
CO
NT2
: MB
boa
rd C
1285
(+ s
ide)
Yes
Che
ck th
e vo
ltage
s ba
sed
on th
e sc
hem
atic
diag
ram
.A
re th
ey o
utpu
t cor
rect
ly?
No
Vol
tage
line
s th
at a
re n
ot o
utpu
t are
sho
rted
to G
ND
.N
o
Failu
re o
f pow
er s
uppl
y IC
-->
Rep
lace
the
IC. R
epla
ce th
e M
B b
oard
if th
ere
is n
oim
prov
emen
t.To
Driv
e flo
wch
art
BU
Adj
ustm
ent F
low
[yy]
~ A
fter B
U/M
BR
epla
cem
ent ~
Yes
Yes
Pow
er s
uppl
y is
OK
Rep
lace
the
MB
boa
rd w
hen
the
parts
on
that
vol
tage
line
can
not b
e id
entif
ied
assh
orte
d.To
Driv
e flo
wch
art
BU
Adj
ustm
ent F
low
[yy]
~ A
fter B
U/M
BR
epla
cem
ent ~
Che
ck th
at th
e ha
rnes
s ha
s be
en in
serte
dpr
oper
ly. I
f the
re is
no
prob
lem
, rep
lace
the
pow
er s
uppl
y bl
ock.
To D
rive
flow
char
tB
U A
djus
tmen
t Flo
w [y
y] ~
Afte
r BU
/MB
Rep
lace
men
t ~
9-3
BDP-BX2/S357/S360/S363
Aud
io s
ectio
n flo
wch
art
Aud
io d
oes
not s
ound
righ
t
Aud
io is
out
put p
rope
rly.
No
Vid
eo is
out
put p
rope
rly.
Yes
To V
ideo
sec
tion
flow
char
t
Yes
Is th
e flu
ores
cent
tube
/LE
D d
ispl
ay c
orre
ct?
No
To M
ain
flow
char
t
Yes
Is th
e dr
ive
oper
atin
g pr
oper
ly?
No
To D
rive
flow
char
t
Yes
Is e
ach
pow
er s
uppl
y su
pplie
d to
the
AU
DIO
Blo
ck?
No
To P
ower
Sup
ply
(Sys
tem
) flo
wch
art
CN
801
pin
1: +
12V
CN
801
pin
3: +
6VC
N80
1 pi
n 5:
-9V
CN
203
pin
21: +
5V
Yes
Che
ck th
e in
put o
f eac
h po
wer
sup
ply.
No
Rep
lace
IC li
nk
Q80
7 (E
mitt
er):
-8V
Q80
8 (E
mitt
er):
+12V
IC80
9 pi
n 5:
+6V
Whe
n Q
807
is d
efec
tive:
Rep
lace
PS
804
Whe
n Q
808
is d
efec
tive:
Rep
lace
PS
802
Whe
n IC
809
is d
efec
tive:
Rep
lace
PS
803
Yes
Che
ck th
e ou
tput
of e
ach
pow
er s
uppl
y.N
oW
hen
IC80
4 is
def
ectiv
e, c
heck
the
outp
ut o
fIC
304.
No
To P
ower
Sup
ply
(Sys
tem
) flo
wch
art
Yes
Is a
n au
dio
syst
em d
igita
l sig
nal i
nput
toIC
804?
No
IC80
4 pi
n 1:
MC
LKIC
804
pin
2: B
CLK
IC80
4 pi
n 3:
DA
TAIC
804
pin
4: L
RC
K
Yes
Are
con
trol s
igna
ls in
put t
o IC
804?
No
IC80
4 pi
n 6:
CS
NIC
804
pin
7: C
CLK
IC80
4 pi
n 8:
CD
TIC
N80
4 pi
n 1:
XA
MU
TEC
N80
4 pi
n 9:
Res
et
Yes
Is a
dig
ital o
utpu
t (H
DM
I/Coa
x/O
pt) s
igna
lou
tput
from
eac
h of
the
Aud
io o
utpu
tco
nnec
tors
?
No
If fa
ulty
, rep
lace
the
MB
boa
rd.
To D
rive
flow
char
tB
U A
djus
tmen
t Flo
w [y
y] ~
Afte
r BU
/MB
Rep
lace
men
t ~
If fa
ulty
, rep
lace
the
MB
boa
rd.
To D
rive
flow
char
tB
U A
djus
tmen
t Flo
w [y
y] ~
Afte
r BU
/MB
Rep
lace
men
t ~
If fa
ulty
, rep
lace
the
MB
boa
rd.
To D
rive
flow
char
tB
U A
djus
tmen
t Flo
w [y
y] ~
Afte
r BU
/MB
Rep
lace
men
t ~
IC30
4 pi
n 4:
+5V
Q80
7 (C
olle
ctor
): -8
VQ
808
(Col
lect
or):
+12V
IC80
4 pi
n 14
: +5V
9-4
BDP-BX2/S357/S360/S363
Vide
o se
ctio
n flo
wch
art
Rep
rodu
ced
vide
o do
es n
ot a
ppea
r rig
ht
Is th
e flu
ores
cent
tube
/LE
D d
ispl
ay c
orre
ct?
No
To M
ain
flow
char
t
Y
es
Is th
e dr
ive
oper
atin
g pr
oper
ly?
No
To D
rive
flow
char
t
Y
es
Che
ck th
e in
put o
f eac
h po
wer
sup
ply.
No
Rep
lace
the
IC li
nk.
Q81
5 (E
mitt
er):
-9V
IC80
5 pi
n 5:
+6V
Whe
n Q
815
is d
efec
tive:
Rep
lace
PS
804
Whe
n IC
805
is d
efec
tive:
Rep
lace
PS
803
Yes
Che
ck th
e ou
tput
of e
ach
pow
er s
uppl
y.N
oC
heck
the
cont
rol o
f eac
h po
wer
sup
ply.
No
Che
ck th
e co
ntro
l lin
es
Q81
5 (C
olle
ctor
): -8
VIC
805
pin
4: +
3.3V
Q81
3 (E
mitt
er):
3.3V
IC80
5 pi
n 1:
5V
Whe
n Q
813
is d
efec
tive:
Che
ck P
CO
NT2
Whe
n IC
805
is d
efec
tive:
Che
ck S
W5V
D
Yes
Yes
Rep
lace
men
t dev
ice
Whe
n Q
801
(Col
lect
or) i
s de
fect
ive:
Rep
lace
Q80
1W
hen
IC80
5 pi
n 4
is d
efec
tive:
Rep
lace
IC80
5
Che
ck -5
V P
ower
sup
ply
No
Rep
lace
men
t dev
ice
IC80
6 O
UTP
UT:
-5V
Rep
lace
IC80
6
Yes
Are
vid
eo s
igna
ls in
put t
o IC
808?
No
Che
ck th
e w
iring
from
IC10
1.
Pin
8 Y
sig
nal
Pin
3 C
sig
nal
Pin
10
Y s
igna
lP
in 1
2 C
b si
gnal
Pin
14
Cr s
igna
l
Yes
Are
con
trol s
igna
ls in
put t
o IC
808?
No
Che
ck th
e w
iring
from
IC10
1.
IC80
8 pi
n 16
PS
1 (X
VM
UTE
+3.
3V)
IC80
8 pi
n 15
PS
2 (X
VM
UTE
+3.
3V)
Yes
Is a
vid
eo s
igna
l out
put f
rom
IC80
8?N
oR
epla
ce IC
808
Yes
Is a
sig
nal o
utpu
t fro
m e
ach
Vid
eo o
utpu
tco
nnec
tor?
No
Che
ck o
utpu
t res
isto
rs (R
8045
, R80
41,
R80
42, a
nd R
8043
).C
heck
the
pin
jack
blo
ck.
9-5
BDP-BX2/S357/S360/S363
Driv
e flo
wch
art
BD
P-B
X2/
S36
0 ca
n pl
ay th
e B
D-d
isc.
NO
Che
ck D
rive
Pow
er S
uppl
yC
N30
1 pi
n 15
: 12V
/pin
12:
5V
?
NO
Che
ck P
S30
1, P
S30
3 an
d P
S30
4R
epla
ce P
S w
hen
open
Ye
s
Y
es
Che
ck/re
plac
e th
e FF
C c
able
, the
n ch
eck
BD
P-B
X2/
S36
0 op
erat
es n
orm
ally
.FF
C C
able
(1-x
xxxx
xxx)
NO
Che
ck th
e O
ptic
al B
lock
Uni
t (B
U) b
y se
rvic
em
ode.
(Flo
wch
art z
z) B
U Io
p is
OK
?N
OR
epla
ce th
e B
U.
Yes
Yes
OK
Opt
ical
Blo
ck C
heck
(Flo
wch
art y
y)
BD
P-B
X2/
S36
0 ca
n pl
ay th
e D
VD
/CD
-dis
c.N
O
Ye
s
Flow
cha
rt N
o.xx
(oth
er c
heck
she
et)
BU
Che
ck F
low
[zz]
~ B
efor
e B
U R
epla
cem
ent ~
BU
Adj
ustm
ent F
low
[yy]
~ A
fter B
U/M
B R
epla
cem
ent ~
Ent
er th
e S
ervi
ce M
ode
Pre
ss <
Ope
n/C
lose
>, <
PLA
Y>,
<S
TOP
> an
dpl
ug in
AC
pow
er.
Rem
ove
the
defe
ctiv
e B
U fr
om L
oadi
ng A
ssy.
Als
o re
mov
e th
e B
U d
umpe
rs (4
pcs)
Sel
ect [
2] D
riveM
enu
Unp
ack
new
par
ts a
nd ta
ke B
arco
de p
hoto
by
cam
era
Sel
ect [
7] D
elta
IOP
Che
ck fo
r che
ckin
g.sp
ecifi
catio
n B
D, D
VD
, CD
; with
in ±
12
NO
Iop
is o
ut o
f spe
cific
atio
n, re
plac
e B
U to
new
one.
Ass
embl
e B
U w
ith d
umpe
rs to
Loa
ding
Ass
’y(ti
ghte
n sc
rew
with
2kg
f)
Ye
s
Che
ck D
riveD
evic
eDia
gO
ptic
al B
lock
Che
ck (F
low
char
t yy)
Dec
ode
the
Bar
code
pho
to b
y us
ing
BD
BU
Dec
.exe
and
sav
e th
e te
xt d
ata
to U
SB
mem
ory
Ent
er th
e se
rvic
e m
ode
and
inse
rt U
SB
mem
ory
to re
ar p
anel
The
Iop
data
is w
ithin
spe
cific
atio
n, tu
rn o
ffth
e po
wer
Sel
ect [
2] D
riveM
enu
[3] R
ewrit
eOP
Dat
aTu
rn O
n th
e P
ower
and
che
ck th
e pl
ayba
ckpe
rform
ance
by
usin
g C
D, D
VD
and
BD
.
Afte
r fin
ishi
ng th
e R
ewrit
e O
P d
ata,
con
firm
[7] D
elta
IOP
Che
ck fo
r BU
Las
er q
ualit
y.
BLX
-104
DV
D T
ES
T D
ISC
:H
LX-5
13C
D T
ES
T D
ISC
:H
LX-A
1
BLX
-104
DV
D T
ES
T D
ISC
: HLX
-513
CD
TE
ST
DIS
C: H
LX-A
1
Th
e fo
llow
ing
case
s ne
ed A
djus
tmen
ts;
(
1) R
epla
ce B
U (M
B is
orig
inal
)
(2)
Rep
lace
MB
(BU
is o
rigin
al)
(
3) R
epla
ce b
oth
BU
and
MB
JI
G R
equi
rem
ent
D
igita
l cam
era
(
reco
mm
end
with
mac
ro m
ode)
B
arco
de d
ecod
er (B
DB
UD
ec.e
xe)
i
nsta
lled
in J
IG
P
C’s
U
SB
mem
ory
E
SD
wor
k be
nch
9-6
BDP-BX2/S357/S360/S363
IFco
n se
ctio
n flo
wch
art (
1/2)
IFco
n bl
ock
pow
er s
uppl
y ch
eck
UN
SW
3.3V
vol
tage
(+3.
3 V
)Is
3.3
V o
utpu
t fro
m IC
301
pin
4?
No
Inpu
t vol
tage
Is +
5.8
V in
put t
o IC
301
pin
5?
No
Is th
e fu
se (P
S30
1) b
low
n?N
oTo
Pow
er S
uppl
y (S
yste
m) f
low
char
t
Yes
Ye
s
Yes
Rep
lace
PS
301
If sy
mpt
oms
do n
ot im
prov
e, c
heck
for
a sh
ort o
n th
e ci
rcui
t boa
rd.
RE
G c
ontro
l vol
tage
Is +
5.8
V in
put t
o IC
301
pin
1?
No
Rep
lace
IC30
1
Ye
s
P_FA
IL d
etec
tion
oper
atio
n ch
eck
Rep
lace
R30
5If
sym
ptom
s do
not
impr
ove,
repl
ace
IC30
1.
Che
ck th
e P
_FA
IL v
olta
ge
Is +
3.3
V o
utpu
t fro
m IC
1404
pin
1?
No
Rep
lace
R14
65 a
nd c
heck
for +
3.3
V a
tIC
1404
pin
1. I
f sym
ptom
s do
not
impr
ove,
repl
ace
IC14
04 (P
_FA
IL d
etec
tion)
.
No
Yes
Mai
n un
it ke
y ch
eck
Key
Tab
leC
heck
of k
ey v
olta
ge fr
om m
ain
unit
Key
Tab
le (
) whe
n ke
y is
pre
ssed
or n
ot p
ress
ed.
No
Is th
e FF
C fr
om C
N14
04 d
isco
nnec
ted?
(Oth
er th
an th
e P
OW
ER
key
)N
o
Is th
e ha
rnes
s fro
m C
N30
1 di
scon
nect
ed?
(PO
WE
R k
ey)
Is th
e FL
-193
har
ness
from
the
pow
er s
uppl
ydi
scon
nect
ed?
(PO
WE
R k
ey)
Yes
Rem
ote
cont
rol o
pera
tion
chec
k
Che
ck th
e w
avef
orm
whe
n th
e re
mot
eco
ntro
l but
ton
is n
ot p
ress
ed.
No
Che
ck w
heth
er th
e FF
C is
dis
conn
ecte
d fro
mC
N14
04. (
Oth
er th
an th
e P
OW
ER
key
)
No
Che
ck o
f the
3.3
V v
olta
geC
N14
04 p
in 1
7, a
nd IC
1403
pin
24
Is th
ere
a pr
oble
m w
ith th
e R
B14
03 m
ount
ing
cond
ition
?
Yes
Che
ck o
f the
wav
efor
m w
hen
the
key
is p
ress
ed.
In c
ompa
rison
with
a n
orm
al w
avef
orm
,is
the
wav
efor
m o
f the
vol
tage
out
put
corr
ectly
?
No
Is th
e re
mot
e co
ntro
l tha
t is
used
in th
ein
spec
tion
brok
en?
No
Doe
s re
plac
emen
t of t
he F
L/FR
boa
rd re
sult
in im
prov
emen
t?
No
Yes
Che
ck w
heth
er th
e FF
C is
dis
conn
ecte
d fro
mC
N14
04. (
Oth
er th
an th
e P
OW
ER
key
)
Y
es
To F
L/FR
boa
rd fl
owch
art
Is th
ere
a pr
oble
m w
ith th
e m
ount
ing
cond
ition
of R
B14
01, o
r 140
2?Is
ther
e a
prob
lem
with
the
mou
ntin
gco
nditi
on o
f C14
14, 1
415,
141
6, o
r 141
7?
PO
WE
R:
CN
301
pin
1 K
EY
0S
TOP
: CN
1404
pin
13
KE
Y 1
OP
EN
/CLO
SE
: CN
1404
pin
14
KE
Y 2
PLA
Y: C
N14
04 p
in 1
5 K
EY
3
9-7
BDP-BX2/S357/S360/S363
IFco
n se
ctio
n flo
wch
art (
2/2)
Che
ck o
f IFc
on re
set i
n put
port
Is th
e vo
ltage
of I
C14
03 p
in 6
"H" (
3.3
V)?
No
Is th
ere
a pr
oble
m w
ith th
e m
ount
ing
cond
ition
of R
1414
, C14
10, o
r R14
08?
Yes
Yes
Pcon
t out
putp
ort c
heck
Che
ck o
f eac
h po
wer
sup
ply
cont
rol p
ort
whe
n th
e po
wer
is O
N C
orre
spon
ding
out
put
IC14
03 p
in 2
0 P
cont
3IC
1403
pin
21
Pco
nt2
IC14
03 p
in 2
8 P
cont
1IC
1403
pin
31
Pco
nt4
IC14
03 p
in 3
2 A
TAP
CO
NT2
IC14
03 p
in 3
3 A
TAP
CO
NT2
SW
3.3V
out
put
1.05
V s
yste
m o
utpu
tD
CS
W3.
3V o
utpu
t1.
8 V
sys
tem
out
put
DR
_SW
12V
out
put
PO
WE
R (3
.3 V
and
1.5
V) o
utpu
t
No
Che
ck fo
r sho
rts a
t eac
h po
rtN
oA
ll th
e po
rts g
o "H
" with
in 2
to 1
0 m
s, b
utso
on g
o "L
".
No
Yes
Yes
Yes
Do
the
sym
ptom
s im
prov
e af
ter c
heck
ing
the
sold
erin
g an
d pa
ttern
of I
C14
03?
No
Pow
er s
u ppl
y ou
tput
che
ckSW
3.3V
Sho
rt c
ircui
t ope
ratio
n ch
eck
Che
ck th
e ou
tput
of t
he c
orre
spon
ding
volta
ge.
No
Whe
n IC
1403
pin
20
Pco
nt3
has
gone
"H",
isth
e S
W3.
3V v
olta
ge o
utpu
t?
Yes
No
To P
ower
Sup
ply
(Sys
tem
) flo
wch
art
Do
the
sym
ptom
s im
prov
e af
ter c
heck
ing
the
mou
ntin
g co
nditi
on o
f R14
39, R
1442
, and
IC14
03 p
in 5
2?
No
Rep
lace
IC14
03 o
r rep
lace
the
MB
boa
rd.
To D
rive
flow
char
tB
U A
djus
tmen
t Flo
w [y
y] ~
Afte
r BU
/MB
Rep
lace
men
t ~
Yes
Che
ck S
YS_R
ST s
igna
l out
put
Is IC
1403
pin
35
"H" (
3.3
V)?
The
mou
ntin
g co
nditi
on o
f R91
9 an
d R
523
are
OK
.
No
Rep
lace
IC14
03 a
nd th
e M
B b
oard
.To
Driv
e flo
wch
art
BU
Adj
ustm
ent F
low
[yy]
~ A
fter B
U/M
BR
epla
cem
ent ~
No
Yes
Che
ck th
e co
mm
unic
atio
n w
ith th
e ho
st C
PU(S
YSC
ON
_REQ
sig
nal c
heck
)
Do
cycl
ical
"H" a
nd "L
" com
mun
icat
ion
wav
efor
ms
com
e to
IC14
03 p
in 3
6?
No
Is th
ere
a pr
oble
m w
ith th
e m
ount
ing
cond
ition
of R
1450
, or 1
462?
No
Do
the
sym
ptom
s im
prov
e af
ter r
epla
cing
IC10
1?
No
Yes
Che
ck th
e co
mm
unic
atio
n w
ith th
e ho
st C
PU(S
eria
l com
mun
icat
ion
sign
al c
heck
)
Do
cycl
ical
"H" a
nd "L
" com
mun
icat
ion
wav
efor
ms
com
e to
IC14
03 p
ins
25, 2
6, a
nd27
?
No
Is th
ere
a pr
oble
m w
ith th
e m
ount
ing
cond
ition
of R
B14
03, R
1430
, R93
7, R
936,
R93
9, o
r R93
8?
No
Rep
lace
IC14
03 o
r rep
lace
the
MB
boa
rd.
To D
rive
flow
char
tB
U A
djus
tmen
t Flo
w [y
y] ~
Afte
r BU
/MB
Rep
lace
men
t ~
Is th
e vo
ltage
at t
he "H
" lev
el (3
.3 V
)?
SW
3.3V
out
put
1.05
V s
yste
m o
utpu
tD
CS
W3.
3V o
utpu
t1.
8 V
sys
tem
out
put
DR
_SW
12V
out
put
PO
WE
R (3
.3 V
and
1.5
V) o
utpu
t
9-8
BDP-BX2/S357/S360/S363
FL/F
R B
oard
flow
char
t (1/
3)
Pow
er b
utto
n on
the
mai
n un
it do
es n
ot w
ork
Ke y
1 do
es n
ot o
pera
te
Doe
s sy
mpt
om im
prov
e w
hen
repl
acin
g th
e FL
boa
rd?
No
To IF
con
sect
ion
flow
char
tIs
ther
e vo
ltage
of a
bout
3.3
V a
t pin
13 o
f CN
701
with
out p
ress
ing
the
keys
?N
oTo
IFco
n se
ctio
n flo
wch
art
Yes
Yes
The
pote
ntia
l of p
in 1
of C
N33
1 do
esno
t cha
nge
from
3.3
V to
nea
r 0V
whe
n pr
essi
ng th
e po
wer
but
ton
No
Che
ck p
atte
rn a
nd S
331
mig
ht b
ebr
oken
.
Che
ck th
e re
sist
ance
of r
esis
tors
of
Key
1 lin
e. A
lso
chec
k th
e su
rrou
ndin
gpa
ttern
.
Yes
Dis
conn
ecte
d ha
rnes
s or
repl
ace
FLbo
ard.
Ke y
ope
ratio
ns c
anno
t be
mad
e on
Key
2 do
es n
ot o
pera
te
Doe
s sy
mpt
om im
prov
e w
hen
repl
acin
g th
e FR
boa
rd?
No
To IF
con
sect
ion
flow
char
tIs
ther
e vo
ltage
of a
bout
3.3
V a
t pin
14 o
f CN
701
with
out p
ress
ing
the
keys
?N
oTo
IFco
n se
ctio
n flo
wch
art
Yes
Yes
Whi
ch ro
w o
f key
s do
not
ope
rate
?R
efer
ence
: Rel
atio
nshi
p of
But
tons
and
Vol
tage
sC
heck
the
resi
stan
ce o
f res
isto
rs o
fK
ey2
line.
Als
o ch
eck
the
surr
ound
ing
patte
rn.
STO
P b
utto
ns ->
To
Key
1 do
es n
ot o
pera
te
OP
EN
/CLO
SE
but
ton
-> T
o K
ey2
does
not
ope
rate
PLA
Y b
utto
n ->
To
Key
3 do
es n
ot o
pera
te
Ke y
3 do
es n
ot o
pera
te
Is th
ere
volta
ge o
f abo
ut 3
.3V
at p
in15
of C
N70
1 w
ithou
t pre
ssin
g th
eke
ys?
No
To IF
con
sect
ion
flow
char
t
Yes
Che
ck th
e re
sist
ance
of r
esis
tors
of
Key
3 lin
e. A
lso
chec
k th
e su
rrou
ndin
gpa
ttern
.
9-9
BDP-BX2/S357/S360/S363
FL/F
R B
oard
flow
char
t (2/
3)
FLD
doe
s no
t lig
htLE
D d
oes
not l
ight
Is th
ere
volta
ge o
f abo
ut 5
.8V
at
PS
701?
No
To "F
LD S
witc
h S
urro
undi
ng C
heck
"Is
ther
e vo
ltage
of a
bout
5.8
V a
tP
S70
1?
No
To "L
ED
Sw
itch
Sur
roun
ding
Che
ck"
Yes
Yes
Is th
ere
volta
ge o
f abo
ut -2
2V a
tJL
701?
No
Che
ck th
e ci
rcui
ts s
urro
undi
ng th
eFL
D D
D C
ON
VE
RTE
R.
If N
G, t
hen
repl
ace
the
FR b
oard
.
Is th
ere
volta
ge o
f abo
ut 5
.8V
at
Em
itter
Q70
9 ?
No
Che
ck th
e "L
ED
Sw
itch
Sur
roun
dch
eck"
If N
G, t
hen
repl
ace
the
FR b
oard
.
Yes
Yes
Is th
ere
volta
ge o
f 3.3
V a
t Pin
43
ofIC
702
?
No
Che
ck th
e 3.
3V li
ne o
f the
FR
boa
rd.
Is th
ere
volta
ge o
f 3.3
V a
t Pin
43
ofIC
702
?
No
Che
ck th
e 3.
3V li
ne o
f the
FR
boa
rd.
Yes
Yes
Is p
in 5
of I
C70
2 os
cilla
ting?
No
Rep
lace
IC70
2. If
no
effe
ct, r
epla
ceth
e FR
boa
rd.
Is p
in 1
and
pin
2 of
IC70
2 ab
out
3.3V
?
No
Rep
lace
IC70
2.If
no e
ffect
, rep
lace
the
FR b
oard
.
Yes
Yes
Is th
ere
inpu
t of p
ulse
to p
ins
7, 8
and
9 of
IC70
2?
No
Rep
lace
FFC
bet
wee
n FR
and
MB
.If
no e
ffect
, the
n go
to "I
FD f
low
"R
epla
ce Q
711
and
Q71
0, if
no
effe
ctth
en re
plac
e FR
boa
rd
Yes
Che
ck c
onne
ctio
n of
FLD
and
IC70
2.R
epla
ce IC
702
if O
K.
If no
effe
ct, r
epla
ce th
e FL
boa
rd.
FLD
Sw
itch
Surr
ound
ing
Che
ck
Is th
e po
tent
ial o
f pin
3 o
f Q70
4 5.
8V?
No
Che
ck th
e 5.
8V li
ne o
f the
FR
boa
rd.
Yes
Is th
e po
tent
ial o
f the
bas
e of
Q70
4ar
ound
5V
?Ye
sIs
the
colle
ctor
vol
tage
of Q
703
abou
t0V
?N
oIs
the
volta
ge o
f the
bas
e of
Q70
3 at
3.3V
?N
oIs
pin
7 o
f CN
701
at 3
.3V
?N
o
Rep
lace
FFC
, and
Che
ck p
atta
ern
near
IC14
03 o
f MB
boa
rd. R
epla
ceIC
1403
or M
B b
oard
if N
G.
To D
rive
flow
char
tB
U A
djus
tmen
t Flo
w [y
y] ~
Afte
rB
U/M
B R
epla
cem
ent ~
No
Yes
Yes
Yes
Rep
lace
Q70
4R
epla
ce Q
704
Rep
lace
Q70
3R
epla
ce th
e FR
boa
rd
9-10
BDP-BX2/S357/S360/S363
FL/F
R B
oard
flow
char
t (3/
3)
LED
Sw
itch
Surr
ound
ing
Che
ck
Is th
e po
tent
ial o
f pin
3 o
f Q70
9 5.
8V?
No
Che
ck th
e 5.
8V li
ne o
f the
FR
boa
rd.
Yes
Is th
e po
tent
ial o
f the
bas
e of
Q70
9ar
ound
5V
?Ye
sIs
the
colle
ctor
vol
tage
of Q
708
abou
t0V
?N
oIs
the
volta
ge o
f the
bas
e of
Q70
8 at
3.3V
?N
oIs
pin
6 o
f CN
701
at 3
.3V
?N
o
Rep
lace
FFC
, and
Che
ck p
atta
ern
near
IC14
03 o
f MB
boa
rd. R
epla
ceIC
1403
or M
B b
oard
if N
G.
To D
rive
flow
char
tB
U A
djus
tmen
t Flo
w [y
y] ~
Afte
rB
U/M
B R
epla
cem
ent ~
No
Yes
Yes
Yes
Rep
lace
Q70
9R
epla
ce Q
709
Rep
lace
Q70
8R
epla
ce th
e FR
boa
rd
Rem
ote
cont
rol d
oes
not o
pera
te
Sym
ptom
impr
ove
whe
n re
plac
ing
FRbo
ard?
No
Are
ther
e si
gnal
s to
pin
17
of M
Bbo
ard
CN
1404
?
No
Rep
lace
FFC
Yes
Yes
Are
ther
e si
gnal
s to
IC14
03 p
in 2
4?N
oC
heck
MB
pat
tern
nea
r IC
1403
Yes
To IF
con
sect
ion
flow
char
t
Is th
ere
outp
ut o
f abo
ut 3
.3V
for
pote
ntia
l of
CN
701
pin
17?
No
Rep
lace
IC70
1 an
d ch
eck
FR b
oard
patte
rn
Yes
Dis
conn
ecte
d fle
xibl
e ha
rnes
s
9-11
BDP-BX2/S357/S360/S363
Fan
flow
char
t
The
FAN
ER
R d
ispl
ay a
ppea
rs o
n th
eflu
ores
cent
tube
sur
face
.
Ent
er th
e S
ervi
ce M
ode
and
turn
on
the
fan
from
the
IFco
n m
enu.
Is th
e vo
ltage
of C
N14
03 p
in 3
on
the
orde
rof
10
V?
No
Dis
conn
ect t
he h
arne
ss fr
om th
e fa
n th
at is
inse
rted
in C
N14
03, a
nd ta
ke th
em
easu
rem
ent a
gain
.Is
it o
n th
e or
der o
f 10
V?
No
Is th
e vo
ltage
of I
C14
01pi
n 2
on th
e or
der o
f3.
3 V
?N
oIs
the
conn
ectio
n be
twee
n IC
1401
pin
1an
dIC
1403
pin
58
brok
en?
Als
o ch
eck
whe
ther
the
trace
is b
ridge
d w
ithth
e ad
jace
nt o
ne.
Yes
Yes
Yes
Is th
e fa
n ro
tatin
g?N
oR
epla
ce th
e fa
n.C
heck
aro
und
the
fan
pow
er s
uppl
y(IC
1401
).
Yes
Is F
anS
tate
of t
he S
ervi
ce M
ode
scre
en s
etto
ON
?N
o
Dis
conn
ect t
he h
arne
ss fr
om th
e fa
n th
at is
inse
rted
in C
N14
03, a
nd s
hort
pins
1 a
nd 2
toge
ther
.D
oes
FanS
tate
of t
he S
ervi
ce M
ode
scre
engo
ON
?
No
Is th
e co
nnec
tion
betw
een
IC14
03 p
in 2
and
IC14
03 p
in 5
5 br
oken
?A
lso
chec
k w
heth
er th
e tra
ce is
brid
ged
with
the
adja
cent
one
.
Yes
Yes
Che
ck w
heth
er s
omet
hing
is c
augh
t in
the
fan
blad
es.
If th
ere
is n
othi
ng th
ere,
repl
ace
the
fan.
Rep
lace
the
fan.
9-12
BDP-BX2/S357/S360/S363
Ethe
rnet
flow
char
t
Can
not c
onne
ct w
ith th
e ne
twor
k, c
anno
tup
date
the
netw
ork.
Is th
e LA
N c
able
plu
gged
in p
rope
rly?
No
Plu
g in
the
LAN
cab
le fi
rmly
.
Y
es
Is th
e LE
D o
f the
hub
rout
er li
t?(L
INK
LE
D)
No
Is p
ower
sup
plie
d to
the
MB
boa
rd?
No
To P
ower
Sup
ply
(Sys
tem
) flo
wch
art
Y
es
Yes
Rep
lace
the
MB
boa
rd.
To D
rive
flow
char
tB
U A
djus
tmen
t Flo
w [y
y] ~
Afte
r BU
/MB
Rep
lace
men
t ~
Are
the
netw
ork
setti
ngs
of th
e m
enu
corr
ect?
No
Mak
e th
e co
rrec
t net
wor
k se
tting
s.
Y
es
Rep
lace
the
MB
boa
rd.
To D
rive
flow
char
tB
U A
djus
tmen
t Flo
w [y
y] ~
Afte
r BU
/MB
Rep
lace
men
t ~
9-13E
BDP-BX2/S357/S360/S363
USB
Dev
ice
flow
char
t
The
USB
dev
ice
is n
ot re
cogn
ized
.
Inse
rt th
e U
SB
dev
ice
agai
n. Is
it re
cogn
ized
whe
n th
e po
wer
istu
rned
OFF
and
then
ON
aga
in?
No
Is 5
V p
rese
nt a
t CN
361
pin
1?N
oIs
5 V
pre
sent
at C
617?
No
Is 5
.8 V
pre
sent
at C
610?
No
Pow
er s
uppl
y bo
ard
defe
ctiv
e
Yes
Y
es
Yes
Yes
Poo
r con
tact
of t
he U
SB
dev
ice
Def
ectiv
e ha
rnes
s be
twee
n th
e U
SB
boar
d an
d th
e M
B b
oard
.D
oes
repl
acin
g IC
601
impr
ove
the
sym
ptom
s?N
oR
epla
ce th
e M
B b
oard
.To
Driv
e flo
wch
art
BU
Adj
ustm
ent F
low
[yy]
~ A
fter
BU
/MB
Rep
lace
men
t ~
Yes
Rep
lace
the
harn
ess
betw
een
the
MB
boar
d an
d th
e U
SB
boa
rd.
Do
the
sym
ptom
s im
prov
e?
No
Rep
lace
the
MB
boa
rd.
To D
rive
flow
char
tB
U A
djus
tmen
t Flo
w [y
y] ~
Afte
rB
U/M
B R
epla
cem
ent ~
IC60
1 de
fect
ive
Y
es
Def
ectiv
e ha
rnes
s be
twee
n th
e U
SB
boar
d an
d th
e M
B b
oard
10-1
BDP-BX2/S357/S360/S363SECTION 10
REPAIR PARTS LIST
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 A-1729-291-A PANEL BLOCK ASSY, FRONT (S360: BR) 1 X-2345-872-1 PANEL ASSY, FRONT
(S360: EXCEPT EC1, EC2, CEK, BR) 1 X-2348-793-1 PANEL ASSY, FRONT (S363) 1 X-2348-794-1 PANEL ASSY, FRONT (S357) 1 X-2348-841-1 PANEL ASSY, FRONT (S360: EC1, EC2, CEK)
2 A-1704-697-A CASE BLOCK (SERVICE USE SOEM) (EXCEPT EC1, EC2, CEK, BR)
2 A-1716-947-A CASE BLOCK (SERVICE USE GDL) (EC1, EC2, CEK, BR)
The components identified by mark or dotted line with mark are critical for safety.Replace only with part number specified.
Les composants identifiés par une marque sont critiquens pour la sécurité.Ne les remplacer que par une pièce portant le numéro spécifié.
3
2
4
3
1
The components identified by mark contain confidential information.Strictly follow the instructions whenever the components are repaired and/or replaced.
Les composants identifiés par la marque contiennent des informations confidentielles.Suivre scrupuleusement les instructions chaque fois qu’un composant est remplacé et / ou réparé.
10-1. EXPLODED VIEWS
10-1-1. CASE SECTION
NOTE:• -XX and -X mean standardized parts, so they
may have some difference from the original one.• Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) ↑ ↑ Parts Color Cabinet’s Color• Items marked “*” are not stocked since they are
seldom required for routine service. Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Accessories and packing materials are given in the last of the electrical parts list.
• Abbreviation AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EA : Saudi Arabia model HK : Hong Kong model KR : Korea model RU : Russian model TH : Thai model TW : Taiwan model
10-2
BDP-BX2/S357/S360/S363
10-1-2. FRONT/REAR CHASSIS SECTION
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
The components identified by mark or dotted line with mark are
critical for safety.Replace only with part number specified.
Les composants identifiés par une marque sont critiquens pour la sécurité.Ne les remplacer que par une pièce portant le numéro spécifié.
The components identified by mark contain confidential information.Strictly follow the instructions whenever the components are repaired and/or replaced.
Les composants identifiés par la marque contiennent des informations confidentielles.Suivre scrupuleusement les instructions chaque fois qu’un composant est remplacé et / ou réparé.
10-4
BDP-BX2/S357/S360/S363
10-1-4. BD SECTION
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 A-1727-332-A LOADING FOR SERVICE 152 4-137-203-01 HOLDER, FFC (EXCEPT EC1, EC2, CEK) 152 4-137-203-11 HOLDER, FFC (EC1, EC2, CEK)
204Audio/Video Cable (Phono Plug x3)(EXCEPT EC1, EC2, CEK, E, BR)
206Conversion Adaptor (E, EA, PX)
205HDMI Cable(BX2/S360: E, BR)
The components identified by mark or dotted line with mark are
critical for safety.Replace only with part number specified.
Les composants identifiés par une marque sont critiquens pour la sécurité.Ne les remplacer que par une pièce portant le numéro spécifié.
10-6
BDP-BX2/S357/S360/S363
10-2. ELECTRICAL PARTS LISTNOTE:• Due to standardization, replacements in the parts
list may be different from the parts specified in the diagrams or the components used on the set.
• -XX and -X mean standardized parts, so they may have some difference from the original one.
• RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable• Items marked “*” are not stocked since they are
seldom required for routine service. Some delay should be anticipated when ordering
these items.• SEMICONDUCTORS In each case, u: μ, for example: uA. . : μA. . uPA. . : μPA. . uPB. . : μPB. . uPC. . : μPC. . uPD. . : μPD. .
• CAPACITORS uF: μF• COILS uH: μH• Abbreviation AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EA : Saudi Arabia model HK : Hong Kong model KR : Korea model RU : Russian model TH : Thai model TW : Taiwan model
The components identified by mark or dotted line with mark are critical for safety.Replace only with part number specified.
Les composants identifiés par une marque sont critiquens pour la sécurité.Ne les remplacer que par une pièce portant le numéro spécifié.
When indicating parts by reference number, please include the board.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R701 1-216-833-11 METAL CHIP 10K 5% 1/10W R702 1-216-033-00 METAL CHIP 220 5% 1/10W R705 1-216-821-11 METAL CHIP 1K 5% 1/10W R707 1-216-828-11 METAL CHIP 3.9K 5% 1/10W R712 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R713 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R714 1-216-838-11 METAL CHIP 27K 5% 1/10W R715 1-216-845-11 METAL CHIP 100K 5% 1/10W R717 1-216-033-00 METAL CHIP 220 5% 1/10W R718 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R719 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R720 1-216-805-11 METAL CHIP 47 5% 1/10W R721 1-216-833-11 METAL CHIP 10K 5% 1/10W
FR-301FL-193
The components identified by mark contain confidential information.Strictly follow the instructions whenever the components are repaired and/or replaced.
Les composants identifiés par la marque contiennent des informations confidentielles.Suivre scrupuleusement les instructions chaque fois qu’un composant est remplacé et / ou réparé.
10-7
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
The components identified by mark contain confidential information.
Strictly follow the instructions whenever the components are repaired and/or replaced.
Les composants identifiés par la marque contiennent des infor-mations confidentielles.Suivre scrupuleusement les instruc-tions chaque fois qu’un composant est remplacé et / ou réparé.
10-8
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
IC301 6-711-237-01 IC NJM2878F3-33 (TE2) IC302 6-711-050-01 IC S-1170B50UC-OUJTFG IC304 6-705-337-01 IC TK11150CSCL-G IC502 6-710-563-01 IC K9F2G08U0A-PCBOT IC601 6-712-613-01 IC SI-3010KM-TLS
IC703 6-706-487-01 IC TC7SH08FU (T5RSOYJF) IC704 6-702-302-01 IC TK11133CSCL-G IC705 6-705-337-01 IC TK11150CSCL-G IC802 6-711-237-01 IC NJM2878F3-33 (TE2) IC804 6-702-630-01 IC AK4382AVTN-E2
IC805 6-711-237-01 IC NJM2878F3-33 (TE2) IC806 8-759-667-17 IC L79M05TLL-SONY-TL-E IC807 8-759-100-96 IC uPC4558G2 IC808 6-713-907-01 IC NJM2564BV (TE2) IC1101 6-712-663-11 IC LAN8700C-AEZG-CTI
IC1351 6-713-929-01 IC BD35630HFV-TR IC1401 6-708-762-01 IC PQ200WNA1ZPH IC1403 6-808-722-01 IC R5F212A7SNA18FP