User Instructions PLEASE READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE. BABY MONITOR 4.3” Video Display [email protected]
User Instructions
PLEASE READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE.
BABY MONITOR4.3” Video Display
IMPORTANT SAFETY INSTRUCTIONS
BEFORE USING THESE APPLIANCES READ ALL INSTRUC-TIONS AND CAUTIONARY MAKINGS IN THIS MANUAL AND ON THE APPLIANCE.
When using an electrical appliance, basic precautions should always be followed, including the following:
1.These devices are not intended for use by persons (includingchildren) with sensory or mental capabilities, or lack of experienceand knowledge, unless they have been given supervision or instruc-tion by a responsible person concerning use of the appliance toensure that they can use it safely.
2.Do not allow to be used as a toy. Close attention is necessary when used by or near children.
3.Suitable for dry locations ONLY. Do not use outdoors or on a wetsurface.
4.Do not handle any part of the plug or device with wet hands.
5.Do not use with a damaged cable or plug. If the supply cable isdamaged it must be replaced by VMAI.
6.If the appliance is not working as it should, has received a sharpblow, has been dropped, damaged, left outdoors, or dropped intowater, do not use and contact the VMAI customer service.
7.Do not stretch the cable or place the cable under strain. Keep thecable away from the heated surface. Do not close a door on thecable, or pull the cable around sharp edges or corners. Arrange thecable away from traffic areas and where it will not be stepped on ortripped over. Do not run the appliance over the cable.
8.Do not unplug by pulling on the cable. To unplug, grasp the plug,not the cable. The use of an extension cable is not recommended.
1
IMPORTANT SAFETY INSTRUCTIONS
BEFORE USING THESE APPLIANCES READ ALL INSTRUC-TIONS AND CAUTIONARY MAKINGS IN THIS MANUAL AND ON THE APPLIANCE.
When using an electrical appliance, basic precautions should always be followed, including the following:
1.These devices are not intended for use by persons (including children) with sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruc-tion by a responsible person concerning use of the appliance to ensure that they can use it safely.
2.Do not allow to be used as a toy. Close attention is necessary when used by or near children.
3.Suitable for dry locations ONLY. Do not use outdoors or on a wet surface.
4.Do not handle any part of the plug or device with wet hands.
5.Do not use with a damaged cable or plug. If the supply cable is damaged it must be replaced by VMAI.
6.If the appliance is not working as it should, has received a sharp blow, has been dropped, damaged, left outdoors, or dropped into water, do not use and contact the VMAI customer service.
7.Do not stretch the cable or place the cable under strain. Keep the cable away from the heated surface. Do not close a door on the cable, or pull the cable around sharp edges or corners. Arrange the cable away from traffic areas and where it will not be stepped on or tripped over. Do not run the appliance over the cable.
8.Do not unplug by pulling on the cable. To unplug, grasp the plug, not the cable. The use of an extension cable is not recommended.
9.Unplug when not in use for extended periods and before mainte-
nance or servicing.
10.Use only VMAI chargers for charging this VMAI Baby Monitor.
11.FIRE WARNING - Do not place this product on or near a cooker or any other hot surface and do not incinerate this appliance even if it is severely damaged. The battery might catch fire or explode.
12.Strangulation Hazard - Children can be STRANGLED in cords. Keep this cord out of the reach of the children (more than 1 meter away).
- or servicing.
Use only VMAI chargers for charging this VMAI Baby Monitor.
FIRE WARNING - Do not place this product on or near acooker or any other hot surface and do not incinerate this applianceeven if it is severely damaged. The battery might catch fire orexplode.
Strangulation Hazard - Children can be STRANGLED incords. Keep this cord out of the reach of the children (more than 1meter away).
2
Getting StartThank you for choosing VMAI Baby Monitor as your partner!
Before using, please check carefully if there was any damage and crack by transit. Please contact us with any problem with [email protected]
We will reply patiently and kindly as soon as possible.
1.Included in the Box
Baby Camera x 2
Baby Monitor x 1
Adaptor (5V DC/1A) x 2
Adaptor (5V DC/1.5A) x 1
User Manual x 1
2.Setting up your Video Baby Monitor
2.1.Connecting the power adapter for the monitor if it is in low battery status.
•Connect the small plug of the adapter to the monitor and the other end to the power socket (Figure 1)
•Only use the enclosed adapter (5V DC/1.5A)
•Recommended charging time of at least 16 hours before the first use.
•Press and hold the POWER button on the top of the display to turn it ON (Figure 2)
3
Figure 1 Figure 2
Figure 3 Figure 4
2.2. Connecting the power adapter for the camera unit
•Connect the small plug of the adapter to the camera and the other end to the power socket (Figure 3)
•Only use the enclosed adapter (5V DC/1A)
•Switch the button by the side of the camera to turn it on (Figure 4)
4
Basic Operations
Monitor Unit
ON/OFF ButtonSwitch ON/OFF - Press and hold 3 seconds
Screen Sleep/Wake - Quick press one time
Menu Key Press to access different menu options
Back Key Press to back to previous directory
UP/DOWN Key Video Brightness / Temperature “+” & “-“
LEFT/RIGHT Key Navigation Key
OK Key Press and confirm the selection
Talk Button Press and hold to talk
Zoom Button Press to digital zoom
Adjust Button Press to adjust the volume level
Camera Unit
ON/OFF Button Switch the button to turn ON/OFF
Pair Button Press and hold to pair the monitor unit
5
3.To Pair the Devices
Please see the below chapter of “Menu and Functions” ---“Setting” ---“Camera”
Menu and FunctionsPress the Menu Button to set and select the functions you need.
Lullabies
Select the Lullabies icon and press the “OK” button, then user can choose lullaby to play from the lullabies list.
It will automatically single cycle the song if choose any lullaby in the display.
It will automatically repeat all lullabies list if select ALL.
Singing volume can be adjusted by choosing the level.
6
7
View
Select the View icon and press the “OK” button, user can view any camera from 1-4 or scan these 4 cameras.
8
Temperature Alarm Setting
By setting the highest and lowest temperature limitation parameters, when room temperature exceeds the limitation setting, monitor will alarm automatically.
9
Feeding Timer
Select the Feeding Timer icon and press the “OK” button, user can choose or customize the alarming time to remind for feeding kids. After selected, an alarm icon will appear in video view interface. If reaches predefined time, monitor will alarm for 5 seconds.
10
VOX
When the baby is sleeping quietly, the camera will not pick any noise, the monitor can switch to the Stand By mode automatical-ly and it switches on again as soon as the baby starts crying.
Select the VOX icon and press the OK button. Use the up and down button to select one of the following options:
“OFF”: The VOX function is disabled. All sounds from the baby room wouldn’t be transmitted, even when the baby is crying.
“Low”: The VOX function is enabled with low sensitivity, sounds are transmitted only when the baby is crying loudly
“Middle”: The VOX function is enabled with medium sensitivity, the camera transmits sounds when the baby is crying normally
“High”: The VOX function is enabled with high sensitivity, even soft sound from the baby room is transmitted
The word “VOX” appears at the top of the screen while this function is enabled.
11
VOX + Power Save: Screen will automatically switch on if sound is detected. The monitor will be switched into sleep mode if no sound is detected in 30s or press the Power Button.
Remarks:
The sound of the monitor is switched off approximately 30 seconds after the camera is no longer picking up any noises. The display remains enabled.
As soon as the camera detects noise, depending on the sensitivity setting, the sound is enabled again and can be heard through the monitor.
12
Warm Tip:
This function is designed for making parents feel relieved without viewing or nobody besides the baby. To let them know whether the baby is crying as soon as possible. If the alarm is too sensitive to bother in life, please TURN IT OFF.
Setting
Some basic settings such as display brightness, time, add/delete cameras can be operated in this function.
13
1.Brightness Level
Users can select brightness levels according to the light changes.
2.Camera
Select the “Add Camera” (it supports add 4 cameras at most) to add connection camera to monitor.
To pair the camera and monitor, select one of the slots from “Add Camera” and press camera “Pair” button to pair within 30 seconds.
To remove the connection, just simply select the corresponding camera in the “Delete Camera”.
14
3.Motion Detection
Users can hear alarm once any movement happened if the function is ON.
Warm Tips:
The function can be sensitive by slow actions from baby and alarm can be frequently triggered. If bothering normal life, please Turn Off the function.
The alarm might not be activated by a fast movement which is probaly defined as an adult’s action.
15
16
4.Other Function
Display time can be set and modified by access “Time” page.
Users can switch 60Hz&50Hz easily by “Frequency” function.
Users can delete all cameras and settings history by “Default Setting”.
To Mount the Camera1.Drill two holes on the wall.
2.Install the green kits in the wall
3.Insert the nails at the bottom of the camera
4.Insert the nails part into the green part (in the wall)
Reset:If the monitor is crushed, please carefully use a needle to press the Reset Key at the lower right back of the monitor; then; the monitor will be shut down. You could restart the monitor by pressing the power button later.
Warm Tips
1.All alarm functions are designed to assist users to take care ofthe baby better and make life easier. If they are so sensitive thatalarm frequently and bother your living, please turn them off.
2.If your devices fail to operate, please ensure that your camera is plugged in the power and plug is working properly. And pleaseensure the monitor has power.
4.WARRANTY - When used strictly in accordance with instruc-tions, if you discover that any parts of the VMAI Baby Monitor aredamaged or broken, whether due to manufacturing, shipping oraccidents while in use, please email us, we will reply you within 24 hrs and help you solve the problem.
Email: [email protected]
3.The camera and monitor are supposed to be paired. If not, please repair it following the instruction. If meet some problems, please feel free to contact us.