-
- 1 -
Denon AVR control protocol
Ver.03
Application model : AVR-X4000
Application terminal: Ethernet
RS-232C
Rev 10.3.0
Version Date Contents Page
01 12.Mar.13 Original 02 25.April.13 Corrected SIMPLAY command
P10,P33 03 21.May.13 Corrected Tuner/HD Radio preset channel
command
TPAN**, TPANMEM**, TPHD**, TPHDMEM**
(** is replaced from "A1
G8" to "01
56")
P26,P27 P48,P49
-
- 2 -
Connector specification
. RS-232C
Connector type: DB-9pin female type, slave straight connection
(DCE type)
( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) ,
4,6,7,8,9pin : NC )
Communication format:
Synchronous system : Tone step synchronization
Communication system : A half duplex
Communication speed : 9600bps
Character length : 8 bits
Parity control : None
Start bit : 1 bit
Stop bit : 1 bit
Communication procedure : Non procedural
Communication data length : 135 bytes (maximum)
-
- 3 -
. Ethernet
Connector type
RJ-45(10BASE-T/100BASE-TX)
Communication format
Communication system : A half duplex
Communication speed : 10Mbps/100Mbps
Communication port : TCP port 23 (telnet)
Communication data length : 135bytes (maximum)
PC
AVR Ethernet
Cross cable
PC
AVR
HUB
Ethernet Straight cable
Ethernet Straight cable
Example
Example
-
- 4 -
NETWORK SETUP of AVR-X4000
>Procedure of Network Setup mode.
(1)Press SETUP MENU button, then Menu appears on FL-display(and
GUI)
(2)Select Setup Menu > Network > Settings .
(3)Set parameters described below.
"On"---Use this setting when DHCP server is on the local
network.
"Off"---Use this setting when DHCP server is not on the local
network.
When sets "Off, please set IP address.
When sets "On, you can confirm the IP address that is set by
server.
When sets "Off, please set Subnet Mask.
When sets "On, you can confirm the Subnet Mask that is set by
server.
Set the address of Gateway when Gateway is on the local
network.
Do not set this parameter when Gateway is not on the local
network.
Do not set this parameter.
Do not set this parameter.
Set this parameter "Off".
(1)Press SETUP MENU button, then Menu appears on FL-display (and
GUI)
(2)Select Setup Menu > Network > IP Control
(3)Set parameters described below.
Always On---Use this setting when using the AVR-X4000 Connected
in a network.
Off In Standby--- Use this setting when not using the AVR-X4000
connected in a network.
This setting is reducing the power consumption in the standby
mode.
-
- 5 -
Protocol specification
The following three data forms are defined.
COMMAND : The message sent to a system(AVR) from a
controller(Touch Panel etc.)
A command to a system is given from a controller.
EVENT : The message sent to a controller (Touch Panel etc.) from
a system (AVR)
The result is sent, when a system is operated directly and a
state changes.
*The form of EVENT presupposes that it is the same as that of
COMMAND.
**Refer to the following table for the contents of COMMAND and
EVENT.
RESPONSE : The message sent to a controller (Touch Panel etc.)
from a system (AVR)
if the request command (COMMAND+?+CR(0x0D)) has came from a
controller.
The RESPONSE should be sent within 200ms of receiving the
COMMAND.
*The form of RESPONSE presupposes that it is the same as that of
EVENT.
Basic specification: The command by ASCII CODE, parameter
expression
*ASCII CODE which can be used is from 0x20 to 0x7F: the alphabet
and the number of 0-9, and space (0x20), some signs,
AND carriage return (0x0D) --- It is used only as a pause
sign.
Command structure: COMMAND + PARAMETER + CR (0x0D)
COMMAND: ASCII CODE of 2 characters
Ex. SI : Select Input source
MS : surround Mode Setting
MV : Master Volume setting
PW : system PoWer setting
PARAMETER : ASCII CODE ( up to 25 characters)
ex. DVD : function name
SUPER STADIUM : surround mode name
*Special Parameter--- ? : for request command
-
- 6 -
The example of a command * is the meaning of 0x0D.
SIDVD : Select Input source DVD
MSSTEREO : surround Mode Set to STEREO
MVUP : Master Volume UP
PWON : system PoWer ON
PWSTANDBY : system PoWer STANDBY
SI? : Request command for now playing input source >>
Return RESPONSE SI***
-
- 7 -
Others
A) COMMAND is receivable also during transmission of EVENT.
B) Since CHANNEL VOLUME changes simultaneously when the SURROUND
MODE changes, the value of the channel volume of all channels
returns as EVENT.
C) CHANNEL VOLUME returns the data of ALL channels by the
present SURROUND MODE also including an intact channel. In this
case,
the data of an intact channel is set to "50".
D) Since SURROUND MODE changes simultaneously when the INPUT
source changes, the SURROUND MODE (and also the value of the
channel
volume of all channels , It described in B) ) returns as
EVENT.
E) When SURROUND MODE is the same in between INPUT source change
before and after, EVENT of SURROUND MODE and CHANNEL VOLUME
does NOT return.
F) Although EVENT of SURROUND MODE returns when the present
SURROUND MODE is set up again, CHANNEL VOLUME does NOT return.
G) When SURROUND MODE is changed, before returning SURROUND MODE
after change as EVENT, the present SURROUND MODE is returned.
H) The RESPONSE should be sent as opposed to the request command
by all the commands with which an EVENT exists , not need to
the another request commands(ex. SV command).
I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum
level of MASTER VOLUME defines 99.
J) If the MASTER VOLUME & CHANNEL VOLUME set with 0.5dB
step, the PARAMETER (with COMMAND and RESPONSE, EVENT) defines
three
ASCII characters as bellows.
Ex. MASTER VOLUME = +18.0dB : MV98
| |
+1.0dB : MV81
+0.5dB : MV805
0dB : MV80
-0.5dB : MV795
-1.0dB : MV79
| |
-79.5dB : MV005
--- : MV00
* At the **.0dB step, only uses two ASCII characters as
PARAMETER, same as usual.
K) 1 seconds later, please transmit the next COMMAND after
transmitting a power on COMMAND
PWON
.
-
- 8 -
COMMAND and PARAMETER list
COMMAND PARAMETER function example PW ON POWER ON/STANDBY change
PWON STANDBY PWSTANDBY ? Return PW Status PW? MV UP MASTER VOLUME
UP/DOWN , direct change to **(**dB) MVUP DOWN MVDOWN ** **:00 to 98
by ASCII , 80=80(0dB), 00=-0(--dB)(MIN) MV80 ? Return MV Status MV?
CV FL UP CHANNEL VOLUME UP/DOWN , direct change to **dB CVFL UP FL
DOWN ---FRONT Lch CVFL DOWN FL ** **:38 to 62 by ASCII , 50=0dB
CVFL 50 FR UP CVFR UP FR DOWN ---FRONT Rch CVFR DOWN FR ** **:38 to
62 by ASCII , 50=0dB CVFR 50 C UP CVC UP C DOWN ---CENTERch CVC
DOWN C ** **:38 to 62 by ASCII , 50=0dB CVC 50 SW UP CVSW UP SW
DOWN ---SUBWOOFER1ch CVSW DOWN SW ** **:38 to 62 by ASCII ,
50=0dB,00=OFF CVSW 50 SW2 UP CVSW UP SW2 DOWN ---SUBWOOFER2ch CVSW
DOWN SW2 ** **:38 to 62 by ASCII , 50=0dB,00=OFF CVSW 50 SL UP CVSL
UP SL DOWN ---SURROUND Lch CVSL DOWN SL ** **:38 to 62 by ASCII ,
50=0dB CVSL 50 SR UP CVSR UP SR DOWN ---SURROUND Rch CVSR DOWN SR
** **:38 to 62 by ASCII , 50=0dB CVSR 50 SBL UP CVSBL UP SBL DOWN
---SURROUND BACK Lch (SBch 2SP) CVSBL DOWN SBL ** **:38 to 62 by
ASCII , 50=0dB CVSBL 50
MV, CV COMMAND : "*" parameter uses two or three ASCII
characters. (see page6 J) section)
-
- 9 -
COMMAND PARAMETER function example CV SBR UP CVSBR UP SBR DOWN
---SURROUND BACK Rch (SBch 2SP) CVSBR DOWN SBR ** **:38 to 62 by
ASCII , 50=0dB CVSBR 50 SB UP CVSB UP SB DOWN ---SURROUND BACKch
(SBch 1SP) CVSB DOWN SB ** **:38 to 62 by ASCII , 50=0dB CVSB 50
FHL UP CVFHL UP FHL DOWN ---FRONT HEIGHT Lch CVFHL DOWN FHL **
**:38 to 62 by ASCII , 50=0dB CVFHL 50 FHR UP CVFHR UP FHR DOWN
---FRONT HEIGHT Rch CVFHR DOWN FHR ** **:38 to 62 by ASCII , 50=0dB
CVFHR 50 FWL UP CVFWL UP FWL DOWN ---FRONT WIDE Lch CVFWL DOWN FWL
** **:38 to 62 by ASCII , 50=0dB CVFWL 50 FWR UP CVFWR UP FWR DOWN
---FRONT WIDE Rch CVFWR DOWN FWR ** **:38 to 62 by ASCII , 50=0dB
CVFWR 50 ? Return CV Status CV?
MV, CV COMMAND : "*" parameter uses two or three ASCII
characters. (see page6 J) section)
-
- 10 -
COMMAND PARAMETER function example MU ON VOLUME MUTE ON/OFF
change MUON OFF MUOFF ? Return MU Status MU? SI PHONO SIPHONO CD
SICD HDRADIO ---HD RADIO (North America model Only) SIHDRADIO TUNER
---FM TUNER(Except North America model) SITUNER DVD SIDVD BD
---Blu-ray SIBD TV ---TV AUDIO SITV SAT/CBL ---CBL/SAT SISAT/CBL
MPLAY ---MEDIA PLAYER SIMPLAY
GAME SIGAME AUX1 SIAUX1 AUX2 SIAUX2 NET ---NETWORK SINET PANDORA
(North America model Only) SIPANDORA SIRIUSXM (North America model
Only) SISIRIUSXM SPOTIFY (North America & Europe model Only)
SISPOTIFY FLICKR SIFLICKR FAVORITES SIFAVORITES IRADIO SIIRADIO
SERVER SISERVER USB/IPOD Select iPod/USB SIUSB/IPOD USB Select
INPUT source iPod/USB and USB Start Playback SIUSB IPD Select INPUT
source iPod/USB and iPod Direct Start Playback SIIPD IRP Select
INPUT source NETWORK and Internet Radio Start Playback SIIRP FVP
Select INPUT source NETWORK and Favorites Start Playback SIFVP ?
Return SI Status SI?
-
- 11 -
COMMAND PARAMETER function example ZM ON MAIN ZONE ON/OFF change
ZMON OFF ZMOFF ? Return ZM Status ZM? FAVORITE1 FAVORITE STATION
1-3 MODE SELECT ZMFAVORITE1 FAVORITE2 ZMFAVORITE2 FAVORITE3
ZMFAVORITE3 FAVORITE4 ZMFAVORITE4 FAVORITE1
MEMORY FAVORITE STATION 1-3 MODE MEMORY ZMFAVORITE1 MEMORY
FAVORITE2 MEMORY
ZMFAVORITE2 MEMORY
FAVORITE3 MEMORY
ZMFAVORITE3 MEMORY
FAVORITE4 MEMORY
ZMFAVORITE4 MEMORY
-
- 12 -
COMMAND PARAMETER function example SD AUTO set AUTO mode
(Priority:HDMI>>DIGITAL>>ANALOG) SDAUTO HDMI set force
HDMI INPUT mode SDHDMI DIGITAL set force DIGITAL INPUT
(Optical,Coaxial)mode SDDIGITAL ANALOG set force ANALOG INPUT mode
SDANALOG ? Return SD Status SD? DC AUTO set DIGITAL INPUT AUTO mode
DCAUTO PCM set DIGITAL INPUT force PCM mode DCPCM DTS set DIGITAL
INPUT force DTS mode DCDTS ? Return DC Status DC? SV ON VIDEO
SELECT mode set to ON SVON
OFF VIDEO SELECT mode cancel SVOFF
DVD VIDEO SELECT mode set to ON, and select source SVDVD
BD ---Blu-ray SVBD
TV ---TV AUDIO SVTV
SAT/CBL ---CBL/SAT SVSAT/CBL
MPLAY ---MEDIA PLAYER SVMPLAY
GAME SVGAME
AUX1 SVSAUX1
AUX2 SVSAUX2
CD SVCD
? Return SV Status SV? SLP OFF MAIN ZONE SLEEP TIMER setting
SLPOFF *** ***:001 to 120 by ASCII , 010=10min SLP120 ? Return SLP
Status SLP?
-
- 13 -
COMMAND PARAMETER function example MS MOVIE Select SURROUND mode
MSMOVIE MUSIC MSMUSIC GAME MSGAME PURE DIRECT MSPURE DIRECT DIRECT
MSDIRECT STEREO MSSTEREO STANDARD MSSTANDARD DOLBY DIGITAL MSDOLBY
DIGITAL DTS SUROUND MSDTS SURROUND MCH STEREO ---MULTI CH STEREO
mode MSMCH STEREO ROCK ARENA MSROCK ARENA JAZZ CLUB MSJAZZ CLUB
MONO MOVIE MSMONO MOVIE MATRIX MSMATRIX VIDEO GAME MSVIDEO GAME
VIRTUAL MSVIRTUAL ? Return MS Status MS? QUICK1 QUICK SELECT 1-5
MODE SELECT MSQUICK1 QUICK2 MSQUICK2 QUICK3 MSQUICK3 QUICK4
MSQUICK4 QUICK5 MSQUICK5 QUICK1 MEMORY QUICK SELECT 1-5 MODE MEMORY
MSQUICK1 MEMORY QUICK2 MEMORY MSQUICK2 MEMORY QUICK3 MEMORY
MSQUICK3 MEMORY QUICK4 MEMORY MSQUICK4 MEMORY QUICK5 MEMORY
MSQUICK5 MEMORY QUICK ? Return MSQUICK Status MSQUICK ?
-
- 14 -
COMMAND PARAMETER function example VS ASPNRM Set Aspect Ratio to
4:3 mode
Set Aspect Ratio to 16:9 mode VSASPNRM
ASPFUL VSASPFUL ASP ? Return VSASP Status VSASP ? SC48P Set
Resolution to 480p/576p VSSC48P SC10I Set Resolution to 1080i
VSSC10I SC72P Set Resolution to 720p VSSC72P SC10P Set Resolution
to 1080p VSSC10P SC10P24 Set Resolution to 10P24 VSSC10P24 SC4K Set
Resolution to 4K VSSC4K SCAUTO Set Resolution to AUTO VSSCAUTO SC ?
Return VSSC Status VSSC ? SCH48P Set Resolution to 480p/576p (HDMI)
VSSCH48P SCH10I Set Resolution to 1080i(HDMI) VSSCH10I SCH72P Set
Resolution to 720p(HDMI) VSSCH72P SCH10P Set Resolution to
1080p(HDMI) VSSCH10P SCH10P24 Set Resolution to 10P24(HDMI)
VSSCH10P24 SCH4K Set Resolution to 4K (HDMI) VSSCH4K SCHAUTO Set
Resolution to AUTO(HDMI) VSSCHAUTO SCH ? Return VSSCH Status(HDMI)
VSSCH ? AUDIO AMP Set HDMI AUDIO Output to AMP VSAUDIO AMP AUDIO TV
Set HDMI AUDIO Output to TV VSAUDIO TV AUDIO ? Return VSAUDIO
Status VSAUDIO ? VPMAUTO Set Video Processing Mode to AUTO
VSVPMAUTO VPMGAME Set Video Processing Mode to GAME VSVPMGAME
VPMMOVI Set Video Processing Mode to MOVIE VSVPMMOVI VPM ? Return
VSVPM Status VSVPM ?
-
- 15 -
COMMAND PARAMETER function example
PS TONE CTRL OFF PARAMETER setting PSTONE CTRL OFF TONE CTRL ON
TONE CONTROL ON/OFF PSTONE CTRL OFF TONE CTRL ? Return PSTONE
CONTROL Status PSTONE CTRL ? CINEMA EQ.ON CINEMA EQ. ON/OFF
PSCINEMA EQ.ON
CINEMA EQ.OFF PSCINEMA EQ.OFF CINEMA EQ. ? Return PSCINEMA
EQ.Status PSCINEMA EQ. ? MODE:MUSIC CINEMA / MUSIC / GAME mode
change PSMODE:MUSIC MODE:CINEMA (This parameter can change DOLBY
PL2,PL2x, DTS NEO:X mode.) PSMODE:CINEMA MODE:GAME ---SB=ON
PL2x mode / SB=OFF
PL2 mode PSMODE:GAME
--- GAME can change DOLBY PL2 & PL2x & DTS NEO:X mode
MODE: ? Return PSMODE: Status PSMODE: ? LOM ON Loudness Management
ON/OFF Control PSLOM ON LOM OFF PSLOM OFF
LOM ? Return PSLOM: Status PSLOM ? PHG LOW PL
z HEIGHT GAIN direct change PSPHG LOW
PHG MID PSPHG MID
PHG HI PSPHG HI PHG ? Return PSPHG Status PSPHG ? SP:FH Speaker
Output set(F.Height/F.Wide/S.Back) PSSP:FH SP:FW PSSP:FW SP:SB
PSSP:SB SP:HW PSSP:HW
SP:BH PSSP:BH
SP:BW PSSP:BW
SP: ? Return PSSP: Status PSSP: ?
-
- 16 -
COMMAND PARAMETER function example PS MULTEQ:AUDYSSEY MultEQ
XT32 mode direct change PSMULTEQ:AUDYSSEY MULTEQ:BYP.LR
PSMULTEQ:BYP.LR MULTEQ:FLAT PSMULTEQ:FLAT MULTEQ:MANUAL
PSMULTEQ:MANUAL
MULTEQ:OFF PSMULTEQ:OFF MULTEQ: ? Return PSMULTEQ: Status
PSMULTEQ: ? DYNEQ ON Dynamic EQ = ON PSDYNEQ ON DYNEQ OFF Dynamic
EQ = OFF PSDYNEQ OFF DYNEQ ? Return PSDYNEQ Status PSDYNEQ ? REFLEV
0 Reference Level Offset=0dB PSREFLEV 0
REFLEV 5 Reference Level Offset=5dB PSREFLEV 5 REFLEV 10
Reference Level Offset=10dB PSREFLEV 10 REFLEV 15 Reference Level
Offset=15dB PSREFLEV 15 REFREV ? Return PSREFLEV Status PSREFLEV ?
DYNVOL HEV Dynamic Volume = Heavy PSDYNVOL HEV DYNVOL MED Dynamic
Volume = Medium PSDYNVOL MED DYNVOL LIT Dynamic Volume = Light
PSDYNVOL LIT DYNVOL OFF Dynamic Volume = OFF PSDYNVOL OFF DYNVOL ?
Return PSDYNVOL Status PSDYNVOL ? LFC ON Audyssey LFC = ON PSLFC
ON
LFC OFF Audyssey LFC = OFF PSLFC OFF
LFC ? Return PSLFC Status PSLFC ?
CNTAMT UP Containment Amount UP/DOWN, direct change to **
PSCNTAMT UP
CNTAMT DOWN **:00 to 99 by ASCII , 00=0, PSCNTAMT DOWN
CNTAMT ** ---AVR-X4000 can be operated from 1 to 7 (01 to 07)
PSCNTAMT **
CNTAMT ? Return PSCNTAMT Status PSCNTAMT ?
-
- 17 -
COMMAND PARAMETER function example PS DSX ONHW Audyssey DSX
ON(Heights & Wides) PSDSX ONHW
DSX ONH Audyssey DSX ON(Heights) PSDSX ONH DSX ONW Audyssey DSX
ON(Wides) PSDSX ONW DSX OFF Audyssey DSX OFF PSDSX OFF DSX ? Return
PSDSX Status PSDSX ? STW UP STAGE WIDTH UP/DOWN, direct change to
**dB PSSTW UP STW DOWN **:00 to 99 by ASCII, 50=0dB PSSTW DOWN STW
** ---AVR-X4000 can be operated from -10 to +10(40 to 60) PSSTW 50
STW ? Return PSSTW Status PSSTW ? STH UP STAGE HEIGHT UP/DOWN ,
direct change to **dB PSSTH UP STH DOWN **:00 to 99 by ASCII ,
50=0dB PSSTH DOWN STH ** ---AVR-X4000 can be operated from -10 to
+10(40 to 60) PSSTH 50 STH ? Return PSSTH Status PSSTH ?
PS COMMAND : "*" parameter uses two or three ASCII characters.
(see page6 J) section)
-
- 18 -
COMMAND PARAMETER function example PS BAS UP BASS UP/DOWN ,
direct change to **dB PSBAS UP BAS DOWN **:00 to 99 by ASCII ,
50=0dB PSBAS DOWN BAS ** ---AVR-X4000 can be operated from -6 to
+6(44 to 56) PSBAS 50 BAS ? Return PSBAS Status PSBAS ? TRE UP
TREBLE UP/DOWN , direct change to **dB PSTRE UP TRE DOWN **:00 to
99 by ASCII , 50=0dB PSTRE DOWN TRE ** ---AVR-X4000 can be operated
from -6 to +6(44 to 56) PSTRE 50 TRE ? Return PSTRE Status PSTRE ?
DRC AUTO Dynamic Compression direct change PSDRC AUTO DRC LOW PSDRC
LOW DRC MID PSDRC MID DRC HI PSDRC HI DRC OFF PSDRC OFF DRC ? PSDRC
? LFE UP LFE UP/DOWN , direct change to **dB PSLEE UP LFE DOWN
**:00 to 99 by ASCII , 00=0dB, 10=-10dB PSLFE DOWN LFE **
---AVR-X4000 can be operated from 0 to -10 PSLFE 10 LFE ? Return
PSLFE Status PSLFE ? EFF UP EFFECT UP/DOWN , EFFECT LEVEL direct
change to **dB PSEFF UP EFF DOWN **:00 to 99 by ASCII , 00=0dB,
10=10dB PSEFF DOWN EFF ** ---AVR-X4000 can be operated from 1 to 15
PSEFF 10 EFF ? Return PSEFF Status PSEFF ? DEL UP DELAY UP/DOWN ,
direct change to ***dB PSDEL UP DEL DOWN ***:000 to 999 by ASCII ,
000=0ms, 300=300ms PSDEL DOWN DEL *** ---AVR-X4000 can be operated
from 0 to 300 PSDEL *** DEL ? Return PSDEL Status PSDEL ?
PS COMMAND : "*" parameter uses two or three ASCII characters.
(see page6 J) section)
-
- 19 -
COMMAND PARAMETER function example PS PAN ON PANORAMA ON/OFF
PSPAN ON PAN OFF PSPAN OFF PAN ? Return PSPAN Status PSPAN ? DIM UP
DIMENSION UP/DOWN , direct change to **dB PSDIM UP DIM DOWN **:00
to 99 by ASCII , 00=0, PSDIM DOWN DIM ** ---AVR-X4000 can be
operated from 0 to 6 PSDIM ** DIM ? Return PSDIM Status PSDIM ? CEN
UP CENTER WIDTH UP/DOWN , direct change to **dB PSCEN UP CEN DOWN
**:00 to 99 by ASCII , 00=0 PSCEN DOWN CEN ** ---AVR-X4000 can be
operated from 0 to 7 PSCEN 07 CEN ? Return PSCEN Status PSCEN ? CEG
UP CENTER GAIN UP/DOWN , direct change to **dB PSCEG UP
CEG DOWN **:00 to 99 by ASCII , 00=0.0 PSCEG DOWN
CEG ** --- AVR-X4000 can be operated from 0.0 to 1.0 PSCEG
10
CEG ? Return PSCEG Status PSCEG ?
SWR ON SW ON/OFF PSSWR ON SWR OFF PSSWR OFF SWR ? Return PSSWR
Status PSSWR ? RSZ S ROOM SIZE direct change PSRSZ S RSZ MS PSRSZ
MS RSZ M PSRSZ M RSZ ML PSRSZ ML RSZ L PSRSZ L RSZ ? Return PSRSZ
Status PSRSZ ? DELAY UP AUDIO DELAY UP/DOWN , direct change to
***dB PSDELAY UP DELAY DOWN ***:000 to 999 by ASCII , 000=0ms,
200=200ms PSDELAY DOWN DELAY *** ---AVR-X4000 can be operated from
0 to 200 PSDELAY 200 DELAY ? Return PSDELAY Status PSDELAY ?
PS COMMAND : "*" parameter uses two or three ASCII characters.
(see page6 J) section)
-
- 20 -
COMMAND PARAMETER function example PS RSTR OFF AUDIO RESTORER
direct change PSRSTR OFF
RSTR LOW PSRSTR LOW
RSTR MED PSRSTR MED
RSTR HI PSRSTR HI
RSTR ? Return PSRSTR Status PSRSTR ?
FRONT SPA FRONT SPEAKER direct change PSFRONT SPA
FRONT SPB PSFRONT SPB
FRONT SPA+B PSFRONT A+B
FRONT? Return PSFRONT Status PSFRONT?
-
- 21 -
COMMAND PARAMETER function example PV OFF Picture Mode=OFF
PVOFF
STD Picture Mode=STANDARD PVSTD
MOV Picture Mode=MOVIE PVMOV
VVD Picture Mode=VIVID PVVVD
STM Picture Mode=STREAM PVSTM
CTM Picture Mode=CUSTOM PVCTM
? Return PV Status PV?
CN UP CONTRAST UP/DOWN , direct change to **dB PVCN UP CN DOWN
**:44 to 56 by ASCII , 50=0 PVCN DOWN CN ** --- AVR-X4000 can be
operated from -6 to +6(44 to 56) PVCN 50 CN ? Return PVCN Status
PVCN ? BR UP BRIGHTNESS UP/DOWN , direct change to **dB PVBR UP BR
DOWN **:00 to 12 by ASCII , 00=0 PVBR DOWN BR ** --- AVR-X4000 can
be operated from 0 to 12 PVBR 12 BR ? Return PVBR Status PVBR ? ST
UP Saturation UP/DOWN , direct change to **dB PVST UP
ST DOWN **:44 to 56 by ASCII , 50=0 PVST DOWN
ST ** --- AVR-X4000 can be operated from -6 to +6(44 to 56) PVST
50
ST ? Return PVST Status PVST ?
HUE UP HUE UP/DOWN , direct change to **dB PVHUE UP HUE DOWN
**:44 to 56 by ASCII , 50=0 PVHUE DOWN HUE ** --- AVR-X4000 can be
operated from -6 to +6(44 to 56) PVHUE 50 HUE ? Return PVHUE Status
PVHUE ? DNR OFF DNR direct change PVDNR OFF DNR LOW PVDNR LOW DNR
MID PVDNR MID DNR HI PVDNR HI DNR ? Return PVDNR Status PVDNR ? ENH
UP ENHANCER UP/DOWN, direct change to **dB PVENH UP ENH DOWN **:00
to 12 by ASCII, 00=0 PVENH DOWN ENH ** --- AVR-X4000 can be
operated from 0 to 12 PVENH 12 ENH ? Return PVENH Status PVENH
?
PV COMMAND : "*" parameter uses two ASCII characters. (see page6
J) section)
-
- 22 -
Z2 Z2CV COMMAND : "*" parameter uses two ASCII characters. (see
page6 J) section)
COMMAND PARAMETER function example Z2 PHONO ZONE2 mode set , and
select source Z2CD | ---The name of PARAMETER is | USB/IPOD the
same as that of the time of SI COMMAND. Z2USB/IPOD USB Select ZONE2
source iPod/USB and USB Start Playback Z2USB IPD Select ZONE2
source iPod/USB and iPod Direct Start Playback Z2IPD IRP Select
ZONE2 source NETWORK and Internet Radio Start Playback Z2IRP FVP
Select ZONE2 source NETWORK and Favorites Start Playback Z2FVP
SOURCE ZONE2 mode cancel Z2SOURCE UP ZONE2 VOLUME UP/DOWN , direct
change to **dB Z2UP DOWN Z2DOWN ** **:00 to 98 by ASCII ,
80=80(0dB), 00=-0(--dB)(MIN) Z280 ON ZONE2 ON/OFF change Z2ON OFF
Z2OFF ? Return Z2 Status Z2? Z2MU ON ZONE2 OUTPUT MUTE ON/OFF
change Z2MUON OFF Z2MUOFF ? Return Z2MU Status Z2MU? Z2CS ST ZONE2
Channel setting Z2CSST MONO Z2CSMONO ? Return Z2CS Status Z2CS?
Z2CV FL UP ZONE2 CHANNEL VOLUME UP/DOWN , direct change to **dB
Z2CVFL UP FL DOWN ---FRONT Lch Z2CVFL DOWN FL ** **:38 to 62 by
ASCII , 50=0dB Z2CVFL 50 FR UP ZONE2 CHANNEL VOLUME UP/DOWN ,
direct change to **dB Z2CVFR UP FR DOWN ---FRONT Rch Z2CVFR DOWN FR
** **:38 to 62 by ASCII , 50=0dB Z2CVFR 50 ? Return Z2CV Status
Z2CV? Z2HPF ON ZONE2 HPF ON/OFF Z2HPFON OFF Z2HPFOFF ? Return Z2HPF
Status Z2HPF?
-
- 23 -
Z2PS COMMAND : "*" parameter uses two ASCII characters. (see
page6 J) section)
COMMAND PARAMETER function example Z2PS BAS UP ZONE2 BASS
UP/DOWN , direct change to **dB Z2PSBAS UP BAS DOWN **:00 to 99 by
ASCII , 00=0dB Z2PSBAS DOWN BAS ** ---AVR-X4000 can be operated
from -10 to +10(40 to 60) Z2PSBAS 50 BAS ? Return Z2PSBAS Status
Z2PSBAS ? TRE UP ZONE2 TREBLE UP/DOWN , direct change to **dB
Z2PSTRE UP TRE DOWN **:00 to 99 by ASCII , 00=0dB Z2PSTRE DOWN TRE
** ---AVR- X4000 can be operated from -10 to +10(40 to 60) Z2PSTRE
50 TRE ? Return Z2PSTRE Status Z2PSTRE ? Z2SLP OFF ZONE2 SLEEP
TIMER setting Z2SLPOFF *** ***:001 to 120 by ASCII , 010=10min
Z2SLP120 ? Return Z2SLP Status Z2SLP? Z2 FAVORITE1 ZONE2 FAVORITE
STATION 1-3 MODE SELECT Z2FAVORITE1 FAVORITE2 Z2FAVORITE2 FAVORITE3
Z2FAVORITE3 FAVORITE4 Z2FAVORITE4 FAVORITE1 MEMORY ZONE2 FAVORITE
STATION 1-3 MODE MEMORY Z2FAVORITE1 MEMORY FAVORITE2 MEMORY
Z2FAVORITE2 MEMORY FAVORITE3 MEMORY Z2FAVORITE3 MEMORY FAVORITE4
MEMORY Z2FAVORITE4 MEMORY QUICK1 ZONE2 QUICK SELECT 1-5 MODE SELECT
Z2QUICK1 QUICK2 Z2QUICK2 QUICK3 Z2QUICK3 QUICK4 Z2QUICK4 QUICK5
Z2QUICK5 QUICK1 MEMORY ZONE2 QUICK SELECT 1-5 MODE MEMORY Z2QUICK1
MEMORY QUICK2 MEMORY Z2QUICK2 MEMORY QUICK3 MEMORY Z2QUICK3 MEMORY
QUICK4 MEMORY Z2QUICK4 MEMORY QUICK5 MEMORY Z2QUICK5 MEMORY QUICK ?
Return Z2QUICK Status Z2QUICK ?
-
- 24 -
Z3 Z3CV COMMAND : "*" parameter uses two ASCII characters. (see
page6 J) section)
COMMAND PARAMETER function example Z3 PHONO ZONE3 mode set , and
select source Z3PHONO | ---The name of PARAMETER is | USB/IPOD the
same as that of the time of SI COMMAND. Z3USB/IPOD USB Select ZONE3
source iPod/USB and USB Start Playback Z3USB IPD Select ZONE3
source iPod/USB and iPod Direct Start Playback Z3IPD IRP Select
ZONE3 source NETWORK and Internet Radio Start Playback Z3IRP
FVP Select ZONE3 source NETWORK and Favorites Start Playback
Z3FVP
SOURCE ZONE3 mode cancel Z3SOURCE UP ZONE3 VOLUME UP/DOWN ,
direct change to **dB Z3UP DOWN Z3DOWN ** **:00 to 98 by ASCII ,
80=80(0dB), 00=-0(--dB)(MIN) Z380 ON ZONE3 ON/OFF change Z3ON OFF
Z3OFF ? Return Z3 Status Z3? Z3MU ON ZONE3 OUTPUT MUTE ON/OFF
change Z3MUON OFF Z3MUOFF ? Return Z3MU Status Z3MU? Z3CS ST ZONE3
Channel setting Z3CSST MONO Z3CSMONO ? Return Z3CS Status Z3CS?
Z3CV FL UP ZONE3 CHANNEL VOLUME UP/DOWN , direct change to **dB
Z3CVFL UP FL DOWN ---FRONT Lch Z3CVFL DOWN FL ** **:38 to 62 by
ASCII , 50=0dB Z3CVFL 50 FR UP ZONE3 CHANNEL VOLUME UP/DOWN ,
direct change to **dB Z3CVFR UP FR DOWN ---FRONT Rch Z3CVFR DOWN FR
** **:38 to 62 by ASCII , 50=0dB Z3CVFR 50 ? Return Z3CV Status
Z3CV? Z3HPF ON ZONE3 HPF ON/OFF Z3HPFON OFF Z3HPFOFF ? Return Z3HPF
Status Z3HPF?
-
- 25 -
Z3PS COMMAND : "*" parameter uses two ASCII characters. (see
page6 J) section)
COMMAND PARAMETER function example Z3PS BAS UP ZONE3 BASS
UP/DOWN , direct change to **dB Z3PSBAS UP BAS DOWN **:00 to 99 by
ASCII , 00=0dB Z3PSBAS DOWN BAS ** ---AVR-X4000 can be operated
from -10 to +10(40 to 60) Z3PSBAS 50 BAS ? Return Z3PSBAS Status
Z3PSBAS ? TRE UP ZONE3 TREBLE UP/DOWN , direct change to **dB
Z3PSTRE UP TRE DOWN **:00 to 99 by ASCII , 00=0dB Z3PSTRE DOWN TRE
** ---AVR-X4000 can be operated from -10 to +10(40 to 60) Z3PSTRE
50 TRE ? Return Z3PSTRE Status Z3PSTRE ? Z3SLP OFF ZONE3 SLEEP
TIMER setting Z3SLPOFF *** ***:001 to 120 by ASCII , 010=10min
Z3SLP120 ? Return Z3SLP Status Z3SLP? Z3 FAVORITE1 ZONE3 FAVORITE
STATION 1-4 MODE SELECT Z3FAVORITE1 FAVORITE2 Z3FAVORITE2 FAVORITE3
Z3FAVORITE3 FAVORITE4 Z3FAVORITE4 FAVORITE1 MEMORY ZONE3 FAVORITE
STATION 1-4 MODE MEMORY Z3FAVORITE1 MEMORY FAVORITE2 MEMORY
Z3FAVORITE2 MEMORY FAVORITE3 MEMORY Z3FAVORITE3 MEMORY FAVORITE4
MEMORY Z3FAVORITE4 MEMORY QUICK1 ZONE3 QUICK SELECT 1-5 MODE SELECT
Z3QUICK1 QUICK2 Z3QUICK2 QUICK3 Z3QUICK3 QUICK4 Z3QUICK4 QUICK5
Z3QUICK5 QUICK1 MEMORY ZONE3 QUICK SELECT 1-5 MODE MEMORY Z3QUICK1
MEMORY QUICK2 MEMORY Z3QUICK2 MEMORY QUICK3 MEMORY Z3QUICK3 MEMORY
QUICK4 MEMORY Z3QUICK4 MEMORY QUICK5 MEMORY Z3QUICK5 MEMORY QUICK ?
Return Z3QUICK Status Z3QUICK ?
-
- 26 -
ANALOG TUNER Control
COMMAND PARAMETER function example
TF ANUP TUNER Frequency UP/DOWN TFANUP ANDOWN TFANDOWN
AN******
(6 digits) --- ****.** MHz at FM band (
-
- 27 -
HD RADIO Control(North America model only)
COMMAND PARAMETER function example TF HDUP HD Channel UP/DOWN ,
direct change TFHDUP HDDOWN TFHDDOWN HD******
(6 digits) --- ****.** kHz at AM band (>050000 is AM.)
****.** MHz at FM band (
-
- 28 -
Network Audio/USB /iPod DIRECT Extended Control
COMMAND PARAMETER function example NS 90 Cursor Up Control NS90
91 Cursor Down Control NS91 92 Cursor Left Control NS92 93 Cursor
Right Control NS93 94 Enter (Play/Pause) Control NS94 9A Play
Control(iRadio/mServer/USB)
Play/Pause Control(iPod Direct) NS9A
9B Pause Control Play/Pause Control(iPod Direct)
NS9B
9C Stop Control NS9C 9D Skip Plus Control NS9D 9E Skip Minus
Control NS9E 9F Manual Search Plus Control(USB/iPod) NS9F
9G Manual Search Plus Control(USB/iPod) NS9G
9H Repeat One (USB/iPod DIRECT/mServer/Spotify) NS9H 9I Repeat
All (USB/iPod DIRECT/mServer/Spotify) NS9I 9J Repeat Off (USB/iPod
DIRECT/mServer/Spotify) NS9J 9K Random On/Repeat ALL
(USB/mServer/Spotify)
Shuffle Songs Control (iPod Direct Only) NS9K
9M Random Off (USB/mServer/Spotify) Shuffle Off Control (iPod
Direct Only)
NS9M
9W Toggle Switch Browse Mode/Remote Mode
Control (iPod Direct Only)
NS9W
9X Page Next Control NS9X
9Y Page Previous Control NS9Y
9Z Manual Search STOP Control(USB/iPod) NS9Z
RPT Repeat(toggle) (Media Server,USB,iPod
Direct,Spotify,AirPlay)
NSRPT
RND Random(toggle)" (Media Server,USB,iPod
Direct,Spotify,AirPlay)
NSRND
-
- 29 -
COMMAND PARAMETER function example
NS A Return Onscreen Display Information List NSA
(ASCII CODE Character) (Return NSA0-NSA8,Refer to Page 39
E Request Onscreen Display Information List NSE
(UTF-8 CODE Character) (Return NSE0-NSE8,Refer to Page 40
D* Direct Text Search(iRadio/mServer/USB only) NSD0
(*:0-9,A-Z)
B** (PRESET No.)
Preset Call
**
00-55 00=CH01,55=CH56
NSB00
C** (PRESET No.)
Preset Memory, Preset stored at No.**
**
00-55 00=CH01,55=CH56
NSC00
H Return Preset Channel 01-56 status
UTF-8
NSH
-
- 30 -
Cursor/Enter/Setup Menu
COMMAND PARAMETER function example
MN CUP Cursor Up Control MNCUP CDN Cursor Down Control MNCDN CLT
Cursor Left Control MNCLT CRT Cursor Right Control MNCRT ENT Enter
Control MNENT RTN RETURN Control MNRTN OPT OPTION Control MNOPT INF
INFO Control MNINF MEN ON Setup Menu ON Control MNMEN ON MEN OFF
Setup Menu OFF Control MNMEN OFF MEN? Return MNMEN(Menu) status
MNMEN?
PRV ON InstaPrevue ON Control MNPRV ON
PRV OFF InstaPrevue OFF Control MNPRV OFF
PRV? Return MNPRV(InstaPrevue) status MNPRV?
ZST ON "All Zone Stereo ON" direct Control MNZST ON
ZST OFF "All Zone Stereo OFF" direct Control MNZST OFF
TRIGGER CONTROL
COMMAND PARAMETER function example TR 1 ON Trigger 1 ON/OFF
Control TR1 ON 1 OFF TR1 OFF 2 ON Trigger 2 ON/OFF Control TR2
ON
2 OFF TR2 OFF
? Return TR status TR?
-
- 31 -
Remote Lock/Panel Lock
COMMAND PARAMETER function example
SY REMOTE LOCK ON REMOTE CONTROL LOCK ON/OFF SYREMOTE LOCK ON
REMOTE LOCK OFF SYREMOTE LOCK OFF PANEL LOCK ON PANEL BUTTON
(Except MASTER VOL.)CONTROL LOCK ON SYPANEL LOCK ON PANEL+V LOCK ON
PANEL BUTTON & MASTER VOL. CONTROL LOCK ON SYPANEL+V LOCK ON
PANEL LOCK OFF PANEL BUTTUM & MASTER VOL. CONTROL LOCK OFF
SYPANEL LOCK OFF
UPGRADE ID Display
COMMAND PARAMETER function example UG IDN ID Number for UPGRADE
is displayed on FL Display UGIDN
-
- 32 -
EVENT(or RESPONSE) and PARAMETER list
EVENT PARAMETER function example PW ON POWER ON/STANDBY change
PWON STANDBY PWSTANDBY MV ** MASTER VOLUME change , **:00 to 98 by
ASCII MV80 98 = 18dB(MAX) 80 = 00dB 01 = -79dB
005 = -79.5dB
00 = ---(MIN) CV FL ** CHANNEL VOLUME change , **:00,38 to 62 by
ASCII CVFL 50 FR ** 62 = +12dB(MAX) CVFR 50 C ** 50 = 0dB CVC 50 SW
** 38 = -12dB(MIN) CVSW 50 SW2 ** 00 = OFF (define ONLY SWch in
DIRECT mode.) CVSW2 50 SL ** CVSL 50 SR ** CVSR 50 SBL ** (at SBch
2SP) CVSBL 50 SBR ** (at SBch 2SP) CVSBR 50 SB ** (at SBch 1SP)
CVSB 50 FHL ** CVFHL 50 FHR ** CVFHR 50 FWL ** CVFWL 50 FWR **
CVFWR 50 MU ON OUTPUT MUTE ON/OFF change MUON OFF MUOFF
The PARAMETER of MV, CV EVENT : Uses two or three ASCII
characters. (see page6 J) section)
-
- 33 -
EVENT PARAMETER function example SI PHONO INPUT source change
SIPHONO CD SICD HDRADIO ---HD RADIO (North America model Only)
SIHDRADIO TUNER ---FM TUNER(Except North America model) SITUNER DVD
SIDVD BD ---Blu-ray SIBD TV ---TV AUDIO SITV SAT/CBL ---CBL/SAT
SISAT/CBL MPLAY ---MEDIA PLAYER SIMPLAY
GAME SIGAME AUX1 SIAUX1 AUX2 SIAUX2 NET ---NETWORK SINET PANDORA
(North America model Only) SIPANDORA SIRIUSXM (North America model
Only) SISIRIUSXM SPOTIFY (North America & Europe model Only)
SISPOTIFY FLICKR SIFLICKR FAVORITES SIFAVORITES IRADIO SIIRADIO
SERVER SISERVER USB/IPOD ---iPod/USB SIUSB/IPOD USB DIRECT SIUSB
DIRECT IPOD DIRECT SIIPOD DIRECT USB SIUSB IPD SIIPD IRP SIIRP FVP
SIFVP
-
- 34 -
EVENT PARAMETER function example ZM ON MAIN ZONE ON/OFF change
ZMON OFF ZMOFF FAVORITE1 FAVORITE STATION 1-3 MODE SELECT
ZMFAVORITE1 FAVORITE2 ZMFAVORITE2 FAVORITE3 ZMFAVORITE3 FAVORITE4
ZMFAVORITE4 FAVORITE1 MEMORY FAVORITE STATION 1-3 MODE MEMORY
ZMFAVORITE1 MEMORY FAVORITE2 MEMORY ZMFAVORITE2 MEMORY FAVORITE3
MEMORY ZMFAVORITE3 MEMORY FAVORITE4 MEMORY ZMFAVORITE4 MEMORY SD
AUTO INPUT mode change SDAUTO HDMI SDHDMI DIGITAL SDDIGITAL ANALOG
SDANALOG ARC ARC playing SDARC NO No Input SDNO DC AUTO DIGITAL
INPUT mode change DCAUTO PCM DCPCM DTS DCDTS SV ON VIDEO SELECT
mode set SVON
OFF VIDEO SELECT mode cancel SVOFF
DVD VIDEO SELECT mode set to ON, and select source SVDVD
BD ---Blu-ray SVBD
TV ---TV AUDIO SVTV
SAT/CBL ---CBL/SAT SVSAT/CBL
MPLAY ---MEDIA PLAYER SVMPLAY
GAME SVGAME
AUX1 SVSAUX1
AUX2 SVSAUX2
CD SVCD
SLP OFF MAIN ZONE SLEEP TIMER setting change SLPOFF ***
SLP120
-
- 35 -
EVENT PARAMETER function example MS DIRECT SURROUND mode change
MSDIRECT PURE DIRECT MSPURE DIRECT STEREO MSSTEREO MULTI CH IN
MSMULTI CH IN M CH IN+PL2X C MSM CH IN+PL2X C M CH IN+PL2X M MSM CH
IN+PL2X M M CH IN+PL2Z H MSM CH IN+PL2Z H M CH IN
+DOLBY EX MSM CH IN+DOLBY EX
MULTI CH IN 7.1 MSMULTI CH IN 7.1 M CH IN+NEO:X C MSM CH
IN+NEO:X C
M CH IN+NEO:X M MSM CH IN+NEO:X M
M CH IN+NEO:X G MSM CH IN+NEO:X G
DOLBY PL2 C MSDOLBY PL2 C DOLBY PL2 M MSDOLBY PL2 M DOLBY PL2 G
MSDOLBY PL2 G DOLBY PL2X C MSDOLBY PL2X C DOLBY PL2X M MSDOLBY PL2X
M DOLBY PL2X G MSDOLBY PL2X G DOLBY PL2Z H MSDOLBY PL2Z H DOLBY
DIGITAL MSDOLBY DIGITAL DOLBY D EX MSDOLBY D EX DOLBY D+PL2X C
MSDOLBY D+PL2X C DOLBY D+PL2X M MSDOLBY D+PL2X M DOLBY D+PL2Z H
MSDOLBY D+PL2Z H DOLBY D+NEO:X C MSDOLBY D+NEO:X C
DOLBY D+NEO:X M MSDOLBY D+NEO:X M
DOLBY D+NEO:X G MSDOLBY D+NEO:X G
-
- 36 -
EVENT PARAMETER function example MS DTS NEO:X C MSDTS NEO:X
C
DTS NEO:X M MSDTS NEO:X M
DTS NEO:X G MSDTS NEO:X G
DTS SURROUND MSDTS SURROUND DTS ES DSCRT6.1 MSDTS ES DSCRT6.1
DTS ES MTRX6.1 MSDTS ES MTRX6.1 DTS+PL2X C MSDTS+PL2X C DTS+PL2X M
MSDTS+PL2X M DTS+PL2Z H MSDTS+PL2Z H DTS+NEO:X C MSDTS+NEO:X C
DTS+NEO:X M MSDTS+NEO:X M
DTS+NEO:X G MSDTS+NEO:X G
DTS96/24 MSDTS96/24 DTS96 ES MTRX MSDTS96 ES MTRX MCH STEREO
MSMCH STEREO ROCK ARENA MSROCK ARENA JAZZ CLUB MSJAZZ CLUB MONO
MOVIE MSMONO MOVIE MATRIX MSMATRIX VIDEO GAME MSVIDEO GAME VIRTUAL
MSVIRTUAL DOLBY D+ MSDOLBY D+ DOLBY D+ +EX MSDOLBY D+ +EX DOLBY D+
+PL2X C MSDOLBY D+ +PL2X C DOLBY D+ +PL2X M MSDOLBY D+ +PL2X M
DOLBY D+ +PL2Z H MSDOLBY D+ +PL2Z H DOLBY D+ +NEO:X C MSDOLBY D+
+NEO:X C
DOLBY D+ +NEO:X M MSDOLBY D+ +NEO:X M
DOLBY D+ +NEO:X C MSDOLBY D+ +NEO:X G
-
- 37 -
EVENT PARAMETER function example DOLBY TRUEHD MSDOLBY HD DOLBY
HD MSDOLBY HD DOLBY HD+EX MSDOLBY HD+EX DOLBY HD+PL2X C MSDOLBY
HD+PL2X C DOLBY HD+PL2X M MSDOLBY HD+PL2X M DOLBY HD+PL2Z H MSDOLBY
HD+PL2Z H DOLBY HD+NEO:X C MSDOLBY HD+NEO:X C
DOLBY HD+NEO:X M MSDOLBY HD+NEO:X M
DOLBY HD+NEO:X G MSDOLBY HD+NEO:X G
DTS HD MSDTS HD DTS HD MSTR MSDTS HD MSTR DTS HD+PL2X C MSDTS
HD+PL2X C DTS HD+PL2X M MSDTS HD+PL2X M DTS HD+PL2Z H MSDTS HD+PL2Z
H DTS HD+NEO:X C MSDTS HD+NEO:X C
DTS HD+NEO:X M MSDTS HD+NEO:X M
DTS HD+NEO:X G MSDTS HD+NEO:X G
DTS ES 8CH DSCRT MSDTS ES 8CH DSCRT DTS EXPRESS MSDTS EXPRESS
MPEG2 AAC (JAPAN model Only) MSMPEG2 AAC AAC+DOLBY EX (JAPAN model
Only) MSAAC+DOLBY EX AAC+PL2X C (JAPAN model Only) MSAAC+PL2X C
AAC+PL2X M (JAPAN model Only) MSAAC+PL2X M
-
- 38 -
EVENT PARAMETER function example MS QUICK1 QUICK SELECT mode
change MSQUICK1 QUICK2 MSQUICK2 QUICK3 MSQUICK3 QUICK4 MSQUICK4
QUICK5 MSQUICK5 QUICK0 ---QUICK 1(or 2, 3, 4, 5) Change QUICK
SELECT OFF MSQUICK0
-
- 39 -
EVENT PARAMETER function example VS ASPNRM ASPECT setting change
VSASPNRM ASPFUL NRM=4:3 , FUL=16:9 VSASPFUL SC48P
Resolution(analog) setting change VSSC48P SC10I VSSC10I SC72P
VSSC72P SC10P VSSC10P SC10P24 VSSC10P24 SC4K VSSC4K SCAUTO VSSCAUTO
SCH48P Resolution(HDMI) setting change VSSCH48P SCH10I VSSCH10I
SCH72P VSSCH72P SCH10P VSSCH10P SCH10P24 VSSCH10P24 SCH4K VSSCH4K
SCHAUTO VSSCHAUTO AUDIO AMP HDMI AUDIO Output setting change
VSAUDIO AMP AUDIO TV VSAUDIO TV VPMAUTO Video Mode setting change
VSVPMAUTO VPMGAME VSVPMGAME VPMMOVI VSVPMMOVI
-
- 40 -
EVENT PARAMETER function example PS TONE CTRL OFF TONE CONTROL
ON/OFF change PSTONE CTRL OFF TONE CTRL ON PSTONE CTRL OFF CINEMA
EQ.ON CINEMA EQ. ON/OFF change PSCINEMA EQ.ON CINEMA EQ.OFF
PSCINEMA EQ.OFF
MODE:CINEMA CINEMA / MUSIC / GAME / HEIGHT mode change
PSMODE:CINEMA MODE:MUSIC PSMODE:MUSIC MODE:GAME PSMODE:GAME
MODE:HEIGHT PSMODE:HEIGHT LOM ON Loudness Management ON/OFF change
PSLOM ON LOM OFF PSLOM OFF
PHG LOW PL
z HEIGHT GAIN change PSPHG LOW
PHG MID PSPHG MID PHG HI PSPHG HI
MULTEQ:AUDYSSEY MultEQ XT32 mode change PSMULTEQ:AUDYSSEY
MULTEQ:BYP.LR PSMULTEQ:BYP.LR MULTEQ:FLAT PSMULTEQ:FLAT
MULTEQ:MANUAL PSMULTEQ:MANUAL MULTEQ:OFF PSMULTEQ:OFF DYNEQ ON
DYNAMIC EQ ON/OFF change PSDYNEQ ON
DYNEQ OFF PSDYNEQ OFF REFLEV 0 Reference Level Offset change
PSREFLEV 0 REFLEV 5 PSREFLEV 5 REFLEV 10 PSREFLEV 10 REFLEV 15
PSREFLEV 15 DYNVOL HEV DYNAMIC VOLUME change PSDYNVOL HEV
DYNVOL MED PSDYNVOL MED
DYNVOL LIT PSDYNVOL LIT DYNVOL OFF PSDYNVOL OFF
-
- 41 -
EVENT PARAMETER function example PS LFC ON Audyssey LFC change
PSLFC ON
LFC OFF PSLFC OFF
CNTAMT ** Containment Amount change PSCNTAMT 07
DSX ONHW Audyssey DSX change PSDSX ONHW DSX ONH PSDSX ONH DSX
ONW PSDSX ONW DSX OFF PSDSX OFF STW ** STAGE WIDTH change PSSTW 50
STH ** STAGE HEIGHT change PSSTH 50
-
- 42 -
EVENT PARAMETER function example PS BAS ** BASS change PSBAS 50
TRE ** TREBLE change PSTRE 50 DRC AUTO Dynamic Compression change
PSDRC AUTO DRC LOW When the input signal is Dolby TrueHD PSDRC LOW
DRC MID PSDRC MID DRC HI PSDRC HI DRC OFF PSDRC OFF LFE ** LFE
change PSLFE 10 EFF ** EFFECT LEVEL change PSEFF 10 DEL *** DELAY
change PSDEL 100 PAN ON PANORAMA ON/OFF change PSPAN ON PAN OFF
PSPAN OFF DIM ** DIMMENSION change PSDIM 06 CEN ** CENTER WIDTH
change PSCEN 07 CEG ** CENTER GAIN change PSCEG 10
SWR ON SW ON/OFF change PSSWR ON
SWR OFF PSSWR OFF RSZ S ROOM SIZE change PSRSZ S RSZ MS PSRSZ MS
RSZ M PSRSZ M RSZ ML PSRSZ ML RSZ L PSRSZ L
DELAY *** AUDIO DELAY change PSDELAY 200 RSTR OFF AUDIO RESTORER
change PSRSTR OFF RSTR LOW PSRSTR LOW
RSTR MED PSRSTR MID
RSTR HI PSRSTR HI
FRONT SPA FRONT SPEAKER direct change PSFRONT SPA
FRONT SPB PSFRONT SPB
FRONT SPA+B PSFRONT A+B
PS COMMAND : "*" parameter uses two or three ASCII characters.
(see page6 J) section)
-
- 43 -
EVENT PARAMETER function example PV OFF Picture Mode=OFF
PVOFF
STD Picture Mode=STANDARD PVSTD
MOV Picture Mode=MOVIE PVMOV
VVD Picture Mode=VIVID PVVVD
STM Picture Mode=STREAM PVSTM
CTM Picture Mode=CUSTOM PVCTM
CN ** CONTRAST change PVCN 50 BR ** BRIGHTNESS Change PVBR 12 ST
** Saturation change PVST 50
HUE ** Hue Change PVHUE 50
DNR OFF DNR change PVDNR OFF DNR LOW PVDNR LOW DNR MID PVDNR MID
DNR HI PVDNR HI ENH ** ENHANCER change PVENH 12
-
- 44 -
EVENT PARAMETER function example Z2 PHONO ZONE2 source change
Z2PHONO | ---The name of PARAMETER is | USB DIRECT
IPOD DIRECT the same as that of the time of SI COMMAND. Z2USB
DIRECT
Z2IPOD DIRECT SOURCE ZONE2 mode cancel Z2SOURCE QUICK1 ZONE2
QUICK SELECT mode change Z2QUICK1 QUICK2 Z2QUICK2
QUICK3 Z2QUICK3 QUICK4 Z2QUICK4 QUICK5 Z2QUICK5 QUICK0 ---Z2
QUICK SELECT 1(or 2, 3, 4, 5)
Change QUICK SELCT OFF Z2QUICK0
FAVORITE1 ZONE2 FAVORITE STATION 1-3 MODE SELECT ZMFAVORITE1
FAVORITE2 ZMFAVORITE2
FAVORITE3 ZMFAVORITE3
FAVORITE4 ZMFAVORITE4
FAVORITE1 MEMORY ZONE2 FAVORITE STATION 1-3 MODE MEMORY
ZMFAVORITE1 MEMORY
FAVORITE2 MEMORY ZMFAVORITE2 MEMORY
FAVORITE3 MEMORY ZMFAVORITE3 MEMORY
FAVORITE4 MEMORY ZMFAVORITE4 MEMORY
** ZONE2 VOLUME change , **:00 to 98 by ASCII Z280 98 =
18dB(MAX) 80 = 00dB 01 = -79dB
00 = ---(MIN)
ON ZONE2 ON/OFF change Z2ON OFF Z2OFF Z2MU ON ZONE2 OUTPUT MUTE
ON/OFF change Z2MUON OFF Z2MUOFF
The PARAMETER of Z2 EVENT : Uses two ASCII characters. (see
page4 J) section)
-
- 45 -
EVENT PARAMETER function example Z2CS ST ZONE2 Channel setting
Z2CSST MONO Z2CSMONO Z2CV FL ** **:38 to 62 by ASCII , 50=0dB
Z2CVFL 50 FR ** **:38 to 62 by ASCII , 50=0dB Z2CVFR 50
Z2HPF ON ZONE2 HPF ON/OFF change Z2HPFON OFF Z2HPFOFF Z2PS BAS
** ZONE2 BASS change Z2PSBAS 50 TRE ** ZONE2 TEBLE change Z2PSTRE
50
-
- 46 -
EVENT PARAMETER function example Z3 PHONO ZONE3 source change
Z3PHONO | ---The name of PARAMETER is | USB DIRECT
IPOD DIRECT the same as that of the time of SI COMMAND. Z3USB
DIRECT
Z3IPOD DIRECT SOURCE ZONE3 mode cancel Z3SOURCE QUICK1 ZONE3
QUICK SELECT mode change Z3QUICK1
QUICK2 Z3QUICK2 QUICK3 Z3QUICK3 QUICK4 Z3QUICK4 QUICK5 Z3QUICK5
QUICK0 ---Z3 QUICK SELECT 1(or 2, 3, 4, 5)
Change QUICK SELCT OFF Z3QUICK0
FAVORITE1 ZONE3 FAVORITE STATION 1-4 MODE SELECT Z3FAVORITE1
FAVORITE2 Z3FAVORITE2 FAVORITE3 Z3FAVORITE3 FAVORITE4
Z3FAVORITE4 FAVORITE1 MEMORY ZONE3 FAVORITE STATION 1-4 MODE MEMORY
Z3FAVORITE1 MEMORY FAVORITE2 MEMORY Z3FAVORITE2 MEMORY FAVORITE3
MEMORY Z3FAVORITE3 MEMORY
FAVORITE4 MEMORY Z3FAVORITE4 MEMORY ** ZONE3 VOLUME change ,
**:00 to 98 by ASCII Z380 98 = 18dB(MAX) 80 = 00dB 01 = -79dB
00 = ---(MIN)
ON ZONE3 ON/OFF change Z3ON OFF Z3OFF Z3MU ON ZONE3 OUTPUT MUTE
ON/OFF change Z3MUON OFF Z3MUOFF
-
- 47 -
EVENT PARAMETER function example Z3CS ST ZONE3 Channel setting
Z3CSST MONO Z3CSMONO Z3CV FL ** **:38 to 62 by ASCII , 50=0dB
Z3CVFL 50 FR ** **:38 to 62 by ASCII , 50=0dB Z3CVFR 50
Z3HPF ON ZONE3 HPF ON/OFF change Z3HPFON OFF Z3HPFOFF Z3PS BAS
** ZONE3 BASS change Z3PSBAS 50 TRE ** ZONE3 TEBLE change Z3PSTRE
50
-
- 48 -
ANALOG TUNER Control
EVENT PARAMETER function example TF AN******
(6 digits) TUNER Frequency change TFAN105000
--- ****.** kHz at AM band (1050.00kHz at AM) ****.** MHz at FM
band TP AN**(PRESET No.) TUNER PRESET change to No.** TPAN01 **
01-56 01=CH01,56=CH56 (PRESET No.01)
ANOFF Change Preset Channel select OFF TPANOFF ANMEM** TUNER
PRESET MEMORY
**
01-56 01=CH01,56=CH56
TPANMEM01
TM ANAUTO ---Tuning mode set to AUTO mode TMANAUTO ANMANUAL
---Tuning mode set to MANUAL mode TMANMANUAL
-
- 49 -
HD RADIO Control(North America model only)
EVENT PARAMETER function example
TF HD****** (6 digits)
--- ****.** kHz at AM band (>050000 is AM.) ****.** MHz at FM
band (
-
- 50 -
EVENT PARAMETER function example HD PTY(18 digits) HD PROGRAM
TYPE change HDPTY (18 digits) ARTIST(40 digits) HD ARTIST NAME
change HDARTIST (40 digits) TITLE(40 digits) HD TITLE NAME change
HDTITLE (40 digits) ALBUM(40 digits) HD ALBUM NAME change HDALBUM
(40 digits) GENRE(23 digits) HD GANRE change HDGENRE (23 digits)
MODE HD MODE(ANALOG/DIGITAL) HDMODE DIGITAL HDMODE ANALOG
-
- 51 -
Network Audio/USB /iPod DIRECT Extended Control
EVENT PARAMETER function example
NSA Onscreen Display Information is Answered By the NSA
Command.
0 Display Line1 Information NSA0**************_?????
1 Display Line3 Information NSA1
************_?????
2 Display Line4 Information NSA2
************_?????
3 Display Line5 Information NSA3
************_?????
4 Display Line6 Information NSA4
************_?????
5 Display Line7 Information NSA5
************_?????
6 Display Line8 Information NSA6
************_?????
7 Display Line9 Information NSA7**************_????? 8 Display
Line10 Information NSA8**************_?????
*:Character Length MAX96byte _:Null ?:Exclusion(The character
after Null
should be disregarded) :Cursor&Playable Information
Data(1Byte)
Bit1:Playable Music Bit2:Directory Bit4:CURSOR SELECT=1
Bit7:Picture Bit3,5,6,8:Don't Care
NSA0Now Playing USB_????
NSA1
Come Away With Me_???
NSA2
Norah Jones_?????????
NSA3
_????????????????????
NSA4
_????????????????????
NSA5
00:11 100%_???????
NSA6
_???????????????????? NSA7_????????????????????
NSA8_????????????????????
-
- 52 -
EVENT PARAMETER function example NSE Onscreen Display
Information(mServer/iRadio) is
Answered By the NSE Command.
0 Display Line1 Information NSE0**************_????? 1 Display
Line3 Information NSE1
************_?????
2 Display Line4 Information NSE2
************_?????
3 Display Line5 Information NSE3
************_?????
4 Display Line6 Information NSE4
************_?????
5 Display Line7 Information NSE5
************_?????
6 Display Line8 Information NSE6
************_?????
7 Display Line9 Information NSE7**************_????? 8 Display
Line10 Information NSE8**************_?????
*:UTF-8 CODE Character(MAX96byte) _:Null ?: Don't Care (The
character after Null
should be disregarded) :Cursor&Playable Information
Data(1Byte)
Bit1:Playable Music =1 Bit2:Directory Bit4:CURSOR SELECT=1
Bit7:Picture Bit3,5,6,8:Don't Care ************_?????:96byte
Fixed
NSE0Now Playing USB_????
NSE1
Come Away With Me_???
NSE2
Norah Jones_?????????
NSE3
_????????????????????
NSE4
_????????????????????
NSE5
00:11 100%_???????
NSE6
_???????????????????? NSE7_????????????????????
NSE8_????????????????????
-
- 53 -
COMMAND PARAMETER function example
NS B** (PRESET No.)
Preset Call
**
00-55 00=CH01,55=CH56
NSB00
C** (PRESET No.)
Preset Memory, Preset stored at No.**
**
00-55 00=CH01,55=CH56
NSC00
H Return Preset Channel CH1-CH56 status
UTF-8
**
00-55 00=CH01,55=CH56
NSH00**********(20 digits) NSH01**********(20 digits) |
NSH54**********(20 digits) NSH55**********(20 digits)
-
- 54 -
Cursor/Enter/Setup Menu
COMMAND PARAMETER function example
MN MEN ON Setup Menu ON Control MNMEN ON
MEN OFF Setup Menu OFF Control MNMEN OFF
PRV ON InstaPrevue ON Control MNPRV ON
PRV OFF InstaPrevue OFF Control MNPRV OFF
ZST ON All Zone Stereo ON Control MNZST ON
ZST OFF All Zone Stereo OFF Control MNZST OFF
TRIGGER CONTROL
EVENT PARAMETER function example
TR 1 ON Trigger 1 ON TR1 ON 1 OFF Trigger 1 OFF TR1 OFF 2 ON
Trigger 2 ON TR2 ON 2 OFF Trigger 2 OFF TR2 OFF
Remote Lock/Panel Lock
EVENT PARAMETER function example
SY REMOTE LOCK ON REMOTE CONTROL LOCK ON/OFF SYREMOTE LOCK ON
REMOTE LOCK OFF SYREMOTE LOCK OFF PANEL LOCK ON PANEL BUTTON(Except
MASTER VOL.)CONTROL LOCK ON SYPANEL LOCK ON PANEL+V LOCK ON PANEL
BUTTON & MASTER VOL. CONTROL LOCK ON SYPANEL+V LOCK ON PANEL
LOCK OFF PANEL BUTTUM & MASTER VOL. CONTROL LOCK OFF SYPANEL
LOCK OFF
UPGRADE ID Display
COMMAND PARAMETER function example UG IDN ************ ID Number
for UPGRADE is displayed on FL Display
************:12-digit ID Number UGIDN ************
IDN NG Cant get ID number from DPMS UGIDN NG
-
- 55 -
Extension COMMAND
The RC code can be sent from Serial protocol commands Protocol
specification
Command structure: COMMAND + RC FORMAT + RC DATA + CR (0x0D)
COMMAND : ASCII CODE of 2 characters
Ex. RC : RC CODE
RC FORMAT : ASCII CODE of 3 characters
Ex. KSK : KASEIKYO FORMAT
SHP : SHARP FORMAT
RC DATA : ASCII CODE of 7 characters
For details of the RC CODE , please refer to the IR remote
control code list.
KASEIKYO FORMAT
SHARP FORMAT
-
- 56 -
The example of a command * is the meaning of 0x0D.
RCKSK0410002 : All Power ON by using KASEIKYO FORMAT
RCSHP0230033 : All Power ON by using SHARP FORMAT