ORDER NO. PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2008 AVIC-F700BT/XS/UC CRT4157 FLASH MEMORY MULTIMEDIA AV NAVIGATION RECEIVER AVIC-F700BT /XS/UC AVIC-F7010BT /XS/UC NAVIGATION AV SYSTEM AVIC-F700BT /XS/EW5 This service manual should be used together with the following manual(s): Model No. Order No. Mech.Module Remarks CX-3195 CRT3815 S10.5COMP2 CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly For details, refer to "Important Check Points for Good Servicing". K-ZZZ.-001 MAY 2008 Printed in Japan
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
For details, refer to "Important Check Points for Good Servicing".
K-ZZZ.-001 MAY 2008 Printed in Japan
C
D
F
A
B
E
1 2 3 4
SAFETY INFORMATION
CAUTION:USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
- Safety Precautions for those who Service this Unit. When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable results.
Caution: 1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept. 2. During repair or tests, do not view laser beam for 10 seconds or longer.
CAUTION
WARNING
Where in a manufacturer’s service documentation, for example in circuit diagrams or listsof components, a symbol is used to indicate that a specific component shall be replaced onlyby the component specified in that documentation for safety reasons, the following symbol shallbe used:
The backlighting lamp of LCD in this equipment contains mercury. Disposal of this material may be regulated due to environmental considerations according to Local, State or Federal Laws. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance: www.eiae.org
This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance: www.eiae.org.
This product contains certain electrical parts contain chemicals which are known to the State ofCalifornia to cause cancer, birth defects or other reproductive harm.Health & Safety Code Section 25249.6 - Proposition 65
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repaircomplex products such as those covered by this manual.Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do soand refer the repair to a qualified service technician.
AVIC-F700BT/XS/UC21 2 3 4
C
D
F
A
B
E
5 6 7 8
WARNING!The AEL (accessible emission level )of the laser power output is less than CLASS 1 but the laser component is capable of emitting radiation exceeding the limit for CLASS 1.A specially instructed person should do servicing operation of the apparatus.
Laser diode characteristicsWave length : 785 nm to 814 nm
Maximum output : 1 190 W(Emitting period : unlimited)
Additional Laser Caution
Transistors Q101 in PCB drive the laser diodes.When Q101 is shorted between their terminals, the laser diodes will radiate beam.If the top cover is removed with no disc loaded while such short-circuit is continued, the naked eyes may be exposed to the laser beam.
AVIC-F700BT/XS/UC 35 6 7 8
C
D
F
A
B
E
1 2 3 4
[Important Check Points for Good Servicing]In this manual, procedures that must be performed during repairs are marked with the below symbol.Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure connections and suitable usage. Please exchange the power cord if necessary.
a Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries. Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance. Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
AVIC-F700BT/XS/UC41 2 3 4
C
D
F
A
B
E
5 6 7 8
CONTENTS SAFETY INFORMATION .....................................................................................................................................21. SERVICE PRECAUTIONS................................................................................................................................6
1.1 SERVICE PRECAUTIONS.........................................................................................................................61.2 NOTES ON SOLDERING...........................................................................................................................7
3. BASIC ITEMS FOR SERVICE ........................................................................................................................173.1 CHECK POINTS AFTER SERVICING .....................................................................................................173.2 PCB LOCATIONS.....................................................................................................................................183.3 JIGS LIST .................................................................................................................................................193.4 CLEANING ...............................................................................................................................................20
4. BLOCK DIAGRAM ..........................................................................................................................................224.1 OVERALL CONNECTION DIAGRAM ......................................................................................................224.2 BLOCK DIAGRAM....................................................................................................................................244.3 POWER SUPPLY SYSTEM FIGURE.......................................................................................................32
6. SERVICE MODE.............................................................................................................................................446.1 TEST MODE.............................................................................................................................................446.2 CD TEST MODE.......................................................................................................................................566.3 uBOOT MENU..........................................................................................................................................596.4 USING THE TEST DISC ..........................................................................................................................60
7. DISASSEMBLY ...............................................................................................................................................668. EACH SETTING AND ADJUSTMENT............................................................................................................75
8.1 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT ....................................................758.2 AV UNIT ADJUSTMENT...........................................................................................................................778.3 FLICKER ADJUSTMENT .........................................................................................................................79
9. EXPLODED VIEWS AND PARTS LIST ..........................................................................................................809.1 PACKING..................................................................................................................................................809.2 EXTERIOR(1) ...........................................................................................................................................849.3 EXTERIOR(2) ...........................................................................................................................................869.4 EXTERIOR(3) ...........................................................................................................................................889.5 CD MECHANISM MODULE .....................................................................................................................90
10. SCHEMATIC DIAGRAM................................................................................................................................9210.1 AV UNIT(PS/IF SECTION)(GUIDE PAGE).............................................................................................9210.2 AV UNIT(A/V SECTION)(GUIDE PAGE) ................................................................................................9810.3 AV UNIT(TUNER SECTION) ................................................................................................................10410.4 AV UNIT(SYSTEM uCOM SECTION)(GUIDE PAGE)..........................................................................10610.5 AV UNIT(RGB LED DRIVER SECTION) .............................................................................................. 11210.6 AV UNIT(IF SECTION)(GUIDE PAGE)................................................................................................. 11410.7 KEYBOARD UNIT ................................................................................................................................12010.8 CD MECHANISM MODULE(GUIDE PAGE).........................................................................................12210.9 WAVEFORMS.......................................................................................................................................128
11. PCB CONNECTION DIAGRAM ..................................................................................................................13011.1 AV UNIT ................................................................................................................................................13011.2 KEYBOARD UNIT.................................................................................................................................13411.3 CD CORE UNIT(S10.5COMP2) ...........................................................................................................136
12. ELECTRICAL PARTS LIST.........................................................................................................................138
AVIC-F700BT/XS/UC 55 6 7 8
C
D
F
A
B
E
1 2 3 4
1. SERVICE PRECAUTIONS1.1 SERVICE PRECAUTIONS
1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual.2. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic induction.3. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment (shorting-solder) by referring to "the DISASSEMBLY".4. After replacing the pickup unit, be sure to check the grating.
EJECT LOCK MODE for CD mechanismIn order to change the EJECT LOCK/UNLOCK status of the mechanism, please perform following procedure.
< Procedure >Top Menu -> AV Source -> Source OFF
Short push area "A" -> Short push area "B" -> Long push area "C" on above screen. (In order to change the status, follow the same operation.)
The current status can be confirmed by "OFF" character color.
A BC
Eject Lock: ONEject Lock: OFF
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.and any use of such marks by Pioneer Corporation is under license. Other trademarks and trade names are those of their respective owners.
AVIC-F700BT/XS/UC61 2 3 4
C
D
F
A
B
E
5 6 7 8
1.2 NOTES ON SOLDERING
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering.
Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C. Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of the soldering iron.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden).
The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia.
AVIC-F700BT/XS/UC 75 6 7 8
C
D
F
A
B
E
1 2 3 4
2. SPECIFICATIONS2.1 SPECIFICATIONS
AVIC-F700BT/XS/UC81 2 3 4
C
D
F
A
B
E
5 6 7 8
AVIC-F700BT/XS/UC 95 6 7 8
C
D
F
A
B
E
1 2 3 4
AVIC-F700BT/XS/UC101 2 3 4
C
D
F
A
B
E
5 6 7 8
2.2 DISC/CONTENT FORMAT
AVIC-F700BT/XS/UC 115 6 7 8
C
D
F
A
B
E
1 2 3 4
2.3 PANEL FACILITIES
.
.
.
.
AVIC-F700BT/XS/UC121 2 3 4
C
D
F
A
B
E
5 6 7 8
AVIC-F700BT/XS/UC 135 6 7 8
C
D
F
A
B
E
1 2 3 4
AVIC-F700BT/XS/UC141 2 3 4
C
D
F
A
B
E
5 6 7 8
2.4 CONNECTION DIAGRAM
AVIC-F700BT/XS/UC 155 6 7 8
C
D
F
A
B
E
1 2 3 4
AVIC-F700BT/XS/UC161 2 3 4
C
D
F
A
B
E
5 6 7 8
3. BASIC ITEMS FOR SERVICE3.1 CHECK POINTS AFTER SERVICING
To keep the product quality after servicing, please confirm following check points.
demrifnocebotmetIserudecorP.oN1 Confirm whether the customer complain has
been solved.If the customer complain occurs with thespecific media, use it for the operation check.
The customer complain must not bereappeared.Display, video, audio and operations must benormal.
2 CD Play back a CD.(Track search)
Display, audio and operations must benormal.
3 FM/AM tuner Check FM/AM tuner action.(Seek, Preset)Switch band to check both FM and AM.
Display, audio and operations must benormal.
4 GPS positioning Connect GPS antenna to the product, andcheck whether the current location is correct.
Current location must be correct.Display and operations must be normal.
Check functions of map scale change andmap scroll.
Display and operations must be normal.
6 data added during the operatingcheck.Check whether no media (CD etc.) is insidethe product.
Make sure to delete data added during theoperating check.The media used for the operating check mustbe ejected.
retfaecnaraeppastinotridrosehctarcsoNkcehcecnaraeppA7receiving it for service.
See the table below for the items to be checked regarding video and audio:
Item to be checked regarding video Item to be checked regarding audionoitrotsiDesion-kcolB
esioNesionlatnoziroHwolootemuloVesiontoD
Disturbed image (video jumpiness) Volume too highgnitautculfemuloVkradooTdetpurretnidnuoSthgirbooT
Mottled color
AVIC-F700BT/XS/UC 175 6 7 8
C
D
F
A
B
E
1 2 3 4
3.2 PCB LOCATIONS
C CD Core Unit(S10.5COMP2)
B
AV UnitA
Keyboard Unit
Unit Number : CWN3170(UC)Unit Number : CWN3168(EW5)Unit Name : AV Unit Unit Number : Unit Name : Keyboard Unit Unit Number : CWX3514 Unit Name : CD Core Unit(S10.5COMP2)
AVIC-F700BT/XS/UC181 2 3 4
C
D
F
A
B
E
5 6 7 8
3.3 JIGS LIST
15P FFC GGD1123 Navi Unit <---> SD Unit74P FFC GGD1560 Navi Unit <---> Panel Unit50P FFC GGD1250 Navi Unit <---> AV Unit20P Extension Cable GGD1327 Navi Unit <---> AV UnitTORX screwdriver GGK1068 T8 (For top cover)15P BBR GGD1561 AV Unit <---> CD Mechanism ModuleTest Disc TCD-782 Checking the gratingL.P.F. Checking the grating (Two pieces)Service Data Disc GGV1322 for Test Mode, Test Disc
- Grease List NameGreaseGrease
Grease No.GEM1024GEM1045
RemarksCD Mechanism ModuleCD Mechanism Module
GGD1327
Navi Unit
GGD1250
GGD1560
CD Mechanism Module
Panel Unit
GGD1561
AV Unit
- Jigs List
AVIC-F700BT/XS/UC 195 6 7 8
C
D
F
A
B
E
1 2 3 4
3.4 CLEANING
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools:
Portions to be cleaned Cleaning toolsCD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008
Portions to be cleaned Cleaning toolsFans Cleaning paper : GED-008
AVIC-F700BT/XS/UC201 2 3 4
C
D
F
A
B
E
5 6 7 8
AVIC-F700BT/XS/UC 215 6 7 8
C
D
F
A
B
E
MIC
CP
42
FM/AM
ANT1
CN1
D ME
J2
/AM ANT
MJ1
1 2 3 4
4. BLOCK DIAGRAM4.1 OVERALL CONNECTION DIAGRAM
}
}
}
}60
LCJ31
REAR CAMERA INPUT
REAR MONITOR OUTPUT
MUTE
REAR OUTPUT
FRONT OUTPUT
1
24
AUDIO INPUT
VIDEO INPUT1
SUBWOOFER OUTPUT
SYSTEM REMOTE CONTROL
CORD ASSY
CN8011
1
74
LCJ1
1
24
CN803
OTJ211
OTJ1
1 10
1LCJ6
LCJ1
LCD MODULE
PANEL UNIT
TOUCH PANEL
CWX3611
CWX3651
CWX1136
C
1
4
LCD MODULE ASSY
VIDEO INPUT2
BT
CN
802
FM
CN
1016
(AV MINIJACK IN)
T
22
22
4
74
CXC8914
C
B KEYBOARD UNIT
:CDP1143
AVIC-F700BT/XS/EW5 :CDP1092
AVIC-F700BT/XS/UCAVIC-F7010BT/XS/UC
AVIC-F700BT/XS/UC221 2 3 4
C
D
F
A
B
E
1
74
1
24
CN
1016
C
5 6 7 8
FAN
GND
10A
POWER SUPPLY TERMINALS
ACC
PKB
ILM
RR-
FL-
RR+
FL+
RL-
FR-
FR+
RL+
CN1005
150
OTJ1
MIC ASSY
GPS ANTENNA ASSY
CXC8574
CPM1064
1
16
AANT
REVPULSE
5
1
CORD ASSY
SPJ221
LCJ1
SPJ11
OT
J5
1
MICBLACK 2.5
1
142
FM/AM TUNER UNIT
GPJ131
CN100120 11
CN100050
1
ANT1401
CN1441
SD UNITCWX3652
CXM1320
115
CD MECHANISM MODULE
115
USB
OTJ6OTJ11BTJ2
FM/AM ANTENNA IN
CDE8561
BUP
CN701
CN701
OTJ2
TMJ1
1
16
1
CN1021IP BUS
11
20
NAVI UNIT
6 15
15
TUNER SECTION
SYSTEM uCOM SECTION
RGB LED DRIVER SECTION
IF SECTION
A/V SECTION
PS/IF SECTION
A AV UNIT
1/6A2/6A3/6A4/6A5/6A6/6A
AVIC-F700BT/XS/UC 235 6 7 8
C
D
F
A
B
E
D(NAV
posite
posite
GND
U
G
1 2 3 4
4.2 BLOCK DIAGRAM
to Titan (NAVIBD)
to CPL
GPS Antenna CONN
USB 2.0 Slot*1
RS232CONN*1
Rear Camera CONN
Speaker CONN Speaker Out
Composite In
Composite In (1)
USB 2.0
GPS AntennaGPSAntenna
RadioAntenna
Com
Com
R-sound InL-sound In
Phone Mute Input
Wire Remote Input
Acc/Bup/ILM
Speed Pulse Input
Parking Signal Input
Reverse Signal Input
Reset
Reset Signal
UART(2)
TMC
Composite In (2)
GUIDANCE (Audio Signal)
Source Audio Signal
CPU WatchdogAn Information of Power offAn Answer of Power off
Reverse Signal
VCC 5 V
Speed Pulse
Control Signal
Video Out CONN
Radio Antenna CONN
Phone Mute CONN
Parking Signal CONN
Wire Remote Input
Reverse Signal Input
Power Supply CONN
Speed Pulse CONN
RF Splitter
I2C
AMP E-vol
SD/MMC Slot SDIO(1)
AVSelector ICAudio Unit
FM/AMTuner
FMMPX DARC
Only AVN-Japan
ArrangeWaveform
ArrangeWaveform
VotageDetecting IC
VotageDetecting ICArrange
Waveform
ArrangeWaveform
LPF
DC/DC Switch
DVD or CD (S10.5 comp2)
Systemu-COM
Sence
Digital Out CONN
3RCA CONN
IP-BUS CONN
SD Board
Audio Unit
RearPannel
AVIC-F700BT/XS/UC241 2 3 4
C
D
F
A
B
E
t
t Signal
T(2)
posite In
Signal)
l
Watchdwer offoff
rse Sign
5 V
d Pulse
comp2)
5 6 7 8
to CPLD(NAVI BD)
Composite In (1)
Composite In (2)
GND
(2)
og
al
Transmitter
Switch
CKS4823-A
5 V In Jack
Digital Out CONN
USB 2.0
H & D GyroADC
I2C(1)
ROM 16-bit
SDIO(1)
133 MHz
USB 2.0
AC97
UART(0)
USP(0)
USB 2.0
GPS Antenna
RS232
I2C(0)UART(2)
VCC 5 V
Reset Signal
ITU-R BT601/6568-bit
Dead Reckoning
G Sensor
GPS Front end
Bluetooth Module
TMC/FM6 Module
BT Antenna
TMC
Mono Out
Speed Pulse
16-bitColor-TFT
Touch Panel4-wire
Headphone Out
LED Driver
LVDS RX
5.8” TFT LCDwith
Touch Panel
LVDS TX
Xilinx CPLDTimingControl
ADC
VolumeController
AuX-in
BT Antenna
Buttons1. Eject2. Menu3. Map4. Mute
DDR1*2(16Meg*32)
SLC Flash 256 MB
Video Decoder
Front PanelKey PadBoard
600 MHz
LCD Board
Navigation Unit
CPU
Audio Codec
UP to 400 MHz DDR or 166 MHz SDRAM Enhanced 32 channel GPS base band 24-bit Color-TFT LCD panel interface 8/16-bit HAND flash interface CMOS/CCD sensor interface USB OTG 2.0 high-speed interface ATA-4 interface (UDMA33) 2 slots SD/SDIO/MMC/MMC4.0/CE-ATA 2 CANBus ports AC97 & I2C Audio CODEC interface3 Universal Serial Ports (USP) & 3 UARTs 2 SPI interface 2 I2C interface PWM interface
AVIC-F700BT/XS/UC 255 6 7 8
C
D
F
A
B
E
IC10A4558R
OLAT
8
T/XS/E
T/XS/U
BT/XS/
3
60835FVE
CT
VDD
SRCM
1 2 3 4
AV UNIT(1/2)A
FL
ANT1401
FM DISTRIBUTION
VICS/TMC AMPNAVI UNIT
TMJ1
FM/AMANTENNA
Q1421
AV8
FLQ1401
T1403T1402
T1401
CN1441 Q1441
FM/AM TUNER UNIT
617 8 93 54
FM
_AN
T
1A
M_A
NT
A
CB
VC
CA
V8
13V
DD
5V
DD
_3.3
TU
3
SL
CE
2C
E1
CK
10 14
DI
DO
TU
NS
L
23Lc
hF
ML
TU
NC
E2
TU
NC
E1
TU
NC
LKT
UN
DO
TU
ND
I
11 18
LDE
TR
DS
_CK
19 20
RD
S_D
AT
AR
DS
_LO
CK
21R
DS
_HS
LK
HR
CK
HLD
ET
HR
DT
HR
LKH
RH
SLK
Q752
Q753
Q754
Q751
A
HRCK
HLDET
HRDT
HRLK
HRHSLK
RO
M_V
DD
134ILLSNS
72TEIN
78SELSDA
79SELSCL
95VST
96VDT
97VCK
FML
B3
GUIDE ISGUIDE
ILMSNS
CDL
B
D
C
IPL
VD8
CD3.3
21
VD(7.5V)
9
8RESET CDRESET
13LOUT CDLVDD(3.3V)
CN701RESET 19
SREMOTE 66
MUTE 85
TUNSL141
TUNCE29
TUNCE18
TUNCLK7
TUNDO5
TUNDI6
LDET26
RCK25
RDT17
RDSLK14
RDS57K18
XOUT
XIN
X60120.000MHz
20
22
CDRESET113
TEMPIN137
TEMP SENSORTH601
103ASENS
73FANCONT
CN
701
C
TO 2/2
77NOSELR
GUIDEMUTENOSELR
AV
SYSTEM-uCOMIC610(1/2)PEG446APEG447A
A
CB
BRST,BRXEN,BSRQ,BDATA,BSCK
A AVIC-F700B
B AVIC-F700B
C AVIC-F7010
D TO 2/2
1
ICBD53
IC603TC7SH04FUS1
IC604TC7S32FU
VOUT2
4
412
Q2860BUP
AVIC-F700BT/XS/UC261 2 3 4
C
D
F
A
B
E
3GUID
C
AVIC-F7
AVIC-F7
AVIC-F7
O 2/2
1B
US1
IC604C7S32F
V
12
Q28
5 6 7 8
30LOUT2
19L4-1
15L3-1
23L5-1
AV SELECTORIC4171
AN15887A
36SCL
35SDA
34VOUT1
6IN2_L
IC1016BA4558RFVM
7
2IN5+_L
3IN4+_L
EVOLIC4271
PML018A
E ISOLATOR/LPF AMP
MUTE
MUTE
MUTE
10
5
Frout_L
IN3_L
11
FL
RLRear_L
12Pre/SW_L
Q4232VR4231Q4231
VIDEO BUFFERVOUT
1VIN
4BCVIN
BACK CAMERA ISOLATORIC4251
NJM2505AF
VCKVDT
20CLK
19DATA
VST 21STB
43V4-1
37V1-1
14
5123
2123
4
22
SREMOTE
PWR AMPIC1007
PAL007C
IN2 OUT2+OUT2-
IN4 OUT4+OUT4-
25B_REMOTE
STBY
MUTE
CN1005
8
12
14
57
ILMILMSNS
ACC
6
CN1016
BCV
12BREMBREMOTE
13
ASENS
11REVREVSNS
9PKBPKBOUT
Q2880
Q2900
PFLPRL
RL+RL-
FL+
CN1000(1/2)
PO
WE
R S
UP
PLY
TE
RM
INA
LSC
OR
D A
SS
YN
AV
I UN
ITO
TJ1
NA
VI U
NIT
SP
J127FRV
FL-
95
13SWL
FLRL
PFLPRL
ANTB16BUP
Q2870
Q4751
7IN1-L
Q4333
Q4331
Q4332
CB
SWL
POMUTE
29
AANT
GUIDEMUTE30
GUIDE32
PKBPKBOUT42
KMODEKMODEOUT43
REVREVSNS44
AUX-LAV2LS12
AUX-VAV2VINNAVIAL
15
VTR1LAV1LS17
VTR1VAV1VIN19
TELMUTE1
TEIN
BCV23
NaviAL23
8KMODEKMODEOUT
Q4752
Q601
MUT
FANV
AV8V
CN1001
2
20
ASENSFANUP
FANCONTQ4771
IQ4776
AV8
468
1012141618
NAVI5V
FU4771
RESETHDRST4
HDRST
FAN DRIVER
PARKING SENS
REVSNS
ASENS
TELMUTE
KMODE
ILMSNSQ4314
Q4312
AV8
00BT/XS/EW5
00BT/XS/UC
010BT/XS/UC
SREMOTE
POMUTE
RSTMUTE
RSTIN
Q1016(2/2)
Q1016(1/2)
5
3
IC608D5335FVE
U
OUT
CT
VDD UVDD5VDD5
SRCMUTE
MUT
4
Q2863
60 Q2861
Q2864
Q2865
Q2862
AV8
AVIC-F700BT/XS/UC 275 6 7 8
C
D
F
A
B
E
1
3V→5VIC605HCT08
5V→3VIC609
VHC08
R651
R650
4
1 2 3 4
NAVI5VIC4601
TPS5103IDB
9
14
Q4661
VCC_SENSE
RWMSKIP
10STBYQ4602
19
18
17
LL48
NAVICON
49DCSKIP
88
104
FCONT
BSENS
OUT_U
OUT_D3
FB
NKBUP
NAVI5V
2INV
FU4601
FU4602
CD7.5VIC4641
TPS5103IDB
14VCC_SENSE
10STBY
Q4642
19
18
17
LL58
VDCONT
OUT_U
OUT_D3
FBBU
VD8
2INV
FU4641
FU4642
92ANTON
ANTB5
Q4601
RT
5
Q4641
RT
DSCKIPCD
36RX
70IPPW
71ASENBO
37TX
Q4733
Q4731
86BSENSN
Q4738
139WREMIN
133WCONT
AV UNIT(2/2)A
121RSTOUT
119OFFINFO
126SYSTOC
131SYSTOCV
117BATFAULT
120CPUWDT
118OFFANS
125CTOSYS
128CTOSYSV
124DVEJKY
112ROT1
111ROT0
CTOSYS5CTOSYSV5
OFFANS5CPUWDT5
3
TC74V
68
11
SYSTOCV5BATFAULT5
SYSTOC5OFFINFO5
9,10
TC74
1,24,5
12,13
Q661
Q662
RESETIC601
TC7SH08FUS1
NAVIC
1,2 4
105106107
LEDDTLEDCKLEDCS
5655
51
SIMUKE0SIMUKE1
SIMUKE4
5352
SIMUKE2SIMUKE3
R658 R655
R657 R654
13VCC
13VCC
69SYSPW
67SWACPW
SWVDD5 VDD5
Q2881
Q2882
SYSPW3.3V NAVI3V
Q4753
Q4754
SYSPW
FU4631ILMV
Q4631
Q4632
BU
Q2811
Q2812
ILMV
4 2AV8
VIDEO5Q2810
BUP
SWACPW
IC2801BA00CC0WCP-V5
AV8
4 2TU3 VT6IC2830
BA00BC0WFP
TU3
VIDEO5
1
1
SYSPWSWACPW
SYSPW
SYSTEM-uCOMIC610(2/2)PEG446APEG447ACB
A
50
VT8
VICS8
VT6
A
AVIC-F700BT/XS/UC281 2 3 4
C
D
F
A
B
E
ANTB
Q47
31
38
YS5YSV5
NS5WDT5
TC7
OCV5AULT5
OC5FO5
9
TC
14
12
Q661
ESETC601H08FUS
IC
4
R658 R
R657 R
8
6
5 6 7 8
BUP35 1,3IC4703
S-L2980A33MC-C6S VDD5
BUP3
AU43,4 1IC1008
NJM2125F AV8
AU4
1 5
6
IC2890TPD1018F BUP
AANT
B
D
C
KBUP
Q4732
Q4734
ASENBO
BU BUP
NKBUP
KBUP
NAVIC+
CD3.33 1IC4702
NJM2885DL1-33 VDD5
CD3.3
VT6
BU
KBUP
33
NAVIC
CN1021
IPBUS-
IPL+IPL
IPBUS+
7
15
IC4721HA12241FP
65
DIN1ROUT
BUS+BUS-
ASENBO8
12
TXRX
8IPPW
STBYIP BUS
CN1015
WIRED REMOTE(Black)
3 1,2
3V→5VIC605
4VHCT08AFTS1
6 4,58 9,1011 12,13
CTOSYSV3CTOSYS3
SYSTOCV3SYSTOC3
OFFANS3CPUWDT3
BATFAULT3
OFFINFO3
ROT1
ROT0
RESETB
,10 8
5V→3VIC609
74VHC08FTS1
,2 3,5 6,13 11
1
CN1000(2/2)
9
ILMR7
ILMG6
ILMB5
EJECTDVEJKY3
ROT117
ROT018
RESETB48
NAVI33V24
CTOSYSV334
CTOSYS337
OFFANS45
WDOGOFFANS3CPUWDT3
47BATTERY-FAULTBATFAULT3
16SYSTOCV3
35SYSTOC3
38OFFINFOOFFINFO3
46
NAVI3VFU2900
A, B, CR643104
R644NM
SIMUKE4R646104
R647NM
SIMUKE3R650104
R651NM
SIMUKE2R654104
R655NM
SIMUKE1R657NM
R658104
SIMUKE0655 R651 R647 R644
654 R650 R646 R643
UVDD5
NAVI UNITOTJ1
TO 1/2
NKBUP
4 2
1
IC2820BA00CC0WCP-V5 KBUP
VT8
ILMR
ILMG
ILMB
ILMV
6 1DI AO1
7 2CLK AO2
8 3LD AO3
Q3604
Q3605
LEDDT
LEDCK
LEDCS
Q3606
Q3601
Q3602
Q3603
RED
GREEN
BLUE
IC3601M62343FP
RGB LED DRIVER
ILMVILMV(LEDSW)
WCONTWIREIN
32
1
VDD55 1IC4701
BD3931HFP KBUP
UVDD5
VDD5
A
B AVIC-F700BT/XS/UC
AVIC-F7010BT/XS/UC
AVIC-F700BT/XS/EW5
C
D TO 1/2
AVIC-F700BT/XS/UC 295 6 7 8
C
D
F
A
B
E
1 2 3 4
KEYBOARD UNITB
RESET
CN801
2
RESETS801
EJECT3
EJECTS804
INT_KEY04
ROT114
1
2
3 A
B
C
Com
Enc-Com
4
7
10
9PUSH
D 8
5
MENUS802
MAPS805
KEY05
INT_KEY16
ROT0 Phase-B
Phase-A
13ROTARY COMMANDER
S803
KEY17
BL-LED8
AUX-V21
AUX-AG20
AUX-VG VGAG
22AUX-L
19
ILMV9
ILMR
D801
10
ILMG11
ILMB
R
G
B12
PUSH
A
C
B D
CN803
3
D815
1
CN802
AV MINIJACK IN
NAVI UNITBTJ2
PANEL UNITOTJ2
R4
L
2AUX-G
1V
2,3
1
BT-ANTANT801
RF_I/O
AVIC-F700BT/XS/UC301 2 3 4
C
D
F
A
B
E
5 6 7 8
CD CORE UNIT(S10.5COMP2)CPICKUP UNIT(P10.5)(SERVICE)
BRST,BRXEN,BSRQ
CN701Q101
M
LASERDIODE
MONITORDIODE
S903DSCSNS
SPINDLEMOTOR
MCARRIAGEMOTOR
LOAD/
LD-
MD
15
5
HOLOGRAM UNIT
IC301BA5839FP IC201
PE5547A
RF-AMP, CD DECODER, MP3/WMA DECODER,
DIGITAL SERVO / DATA PROCESSOR
CDDRIVER
2VD
VD
13LOUT
9
CN101
16SOP
15SOM
18LCOP
17LCOM
21CLCONT
55LOUT
9CONT
TD,FD
AC,BD,F,E
SD,MD
S901HOME
S90412EJ
S9058EJ
LD+ 14
141LD
142PD
12EJ
CONT
CLCONT
HOME
8
9
43
41
VDD
1
VDD
BDATA,BSCK
Q102
39/PUEN
VDD
15
5
FOCUS ACT.TRACKING ACT.
FOP
TOP21 TOP
FOP
11 FOP14 TOP
21
14
8EJ7
DSCSNS6
VCC
16/RESET 8/RESET
88VREFREFO 133
REFOUT
33FOM FOM
12 FOM
44TOM TOM
13 TOM
22LOEJ LOEJ5
52
50
X201
XTAL
/XTAL16.93MHz
VDSENS11
VD
CN701A
AVIC-F700BT/XS/UC 315 6 7 8
C
D
F
A
B
E
POW
->SYS4VHCT
2 mA
ERN
1 2 3 4
4.3 POWER SUPPLY SYSTEM FIGURE
+B
AV UNIT
SYS u-comM30878FJBGP
VDD5REGULARPOWER SUPPLY5 VBD3931HFP HA12241FP
IP-BUS DRIVER
RESET ICBD5335FVE
NAVI -> SYSTC74VHCT08T
UVDD5
ROM COLLECTIONS-93C568DOI
BUP 3 VS-L2980A33MC-C6C
ATT CONTROLUMD3N*3
+
DCSKIPCD
FM/AMTUNERUNITX-2026
VT8(8 V)BA00CC0WFP
typ 103 mAmax 140 mA
typ 172 mAmax 200 mA
DISTRIBUTORMACHINE
+
TU3BA00CC0WFP
SYSPW orSWACPW
SYSPWIR REMOTERPMS2401-H19E4AV
2 mA2 mA2 mA
SWVDD5
MS5TC7
SYS -> MSTC74VHC08FT
2 mA
1 mA
MAX 45 mATYP 32 mA2 mA
FM/AM TunerFront stepamplifier
TMC/VICS/MSN/DirectTuner Front step amplifier
63 mA
4 mA
11 mA
81 mA
172 mA
25.4 mA
25.4 mA
27.3 mA
427 mA
+
RGB_LED DRIVM62343&UMX1
3 mA
DA B C E
AVIC-F700BT/XS/UC321 2 3 4
C
D
F
A
B
E
YST08T
MR
6
MT
S08FT
irectmplifier
_LED D343&UM
3 mA
5 6 7 8
POWER SUPPLY
RQ(WDT,IRQ)TC7WH32FU
3 -> 5AND IPDTC7SET08FU
RST INVTC74SH04
2 mA
OR MUTE CIRCUITTC7S32FU
2 mA
AV SELECTOR
2 mA
S5 ->SYSC74VHCT32T
2 mA 2 mA
TEMPERATURE CIRCUITRIVERX1N
AVIC-F700BT/XS/UC 335 6 7 8
C
D
F
A
B
E
SNS
NAVIHCT08
1 2 3 4
D/D
CD 7.5 V(S10.5)
IP_BUS POWER SUPPLYSW
ASENBO
POWER , AMPPAL007B
SW FOR ANT +
ANTON
SYSPWR orSWACPW
AUTO ANTENNA
AV8(8.3 V)BA00CCOWCP
SWACP
VIDEO ISOLATORNJM2505F
typ 19 mAmax 29.0 mA
VIDEO 5 V
VDCONT
D/DNAVI 5 V
NAVICO
max 2.5A
CD 3.3 VNJM2885DL1-33
MAX 230 mATYP 160 mACD Source OFF40 mA
FCONT
FCONT
S10.5(CD)
SYSPW
ILMV 9 V
KMOD TR PKBSYSPW
SYS->NAVITC7SH08FU
SYS->TC74V
NAVI 3.3 V
ILMV
MAX 1 100 mATYP 300 mACD Source OFF20 mA
DCSKIP
121.6 mA
181.1 mA
24 mA
326.7 mA
30 mA
VDD5
VT8
DA B C E
NAVI, LCD BORD
AVIC-F700BT/XS/UC341 2 3 4
C
D
F
A
B
E
P
SYTC
5 6 7 8
GUIDE MIXNJM2060V
MUTE CIRCUIT
AU4NJM2125
CAPTAIN6
AV SELECTORAN15887A
KB SNS
S->NAVI74VHCT08FTS1
50 mA9 mA
1 mA37 mA
8.4 mA
KEY BORD
AVIC-F700BT/XS/UC 355 6 7 8
C
D
F
A
B
E
K(200 ms
K(200 ms
K(200 ms
1 2 3 4
5. DIAGNOSIS5.1 OPERATIONAL FLOWCHART
Acc on (USUALLY Acc ON)/BSENS
/ASENS
STATUS
MUTE
ASENBO
SREMOTE
SYSPW
DCSKIPCD
ANTON
SWACPW
DCSKIP
BSENSN
RSTOUT
BATFAULT
CPUWDT
OFFINFO
OFFANS
NAVICON
FANCONTFAN CONTROL
200 msEXTERNALOUTPUTAUDIO
CONTROL
NAVI POWERSUPPLY
CONTROL
NAVI CONTROL
ANTON (Source interlockingmovement, forced OFF)
250 300 ms( SURVEY) POWER SUPPLY MAS1 sec 2 sec
IP-BUSPRETREATMENT
IP-BUS SLAVECONNECTION CHECK
SOUND MUTECONTROL
POWER SUPPLY MAS
SENSE SYSTEM
POWERSUPPLY
CONTROL
IP-BUSSYSTEM
POWER SUPPLY MAS
WAITING FOR SLAVEPOWER SUPPLY
OSCILLATION STOP STANDBY LOOP
500 ms
(At the time of a reset start)
AVIC-F700BT/XS/UC361 2 3 4
C
D
F
A
B
E
R SUPPLY
R SUPPLY
R SUPPLY
5 6 7 8
8 ms to 16 ms or more
FANCONT(At the time of high temperature)
MASK(200 ms)
16 ms
MAIN LOOP
After mute (300 ms)(After SYSPWR ON, at least 300 ms. MUTE time is extended to OFFANS Low henceforth.)
MASK(200 ms)
MASK(200 ms)
AVIC-F700BT/XS/UC 375 6 7 8
C
D
F
A
B
E
1 2 3 4
5.2 ERROR CODE LIST
- Error MessagesIf a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the users and also for facilitating trouble analysis and repair work in servicing.
(1) Basic Indication Method
1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains in blank as before.
2) Head unit display examples
Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.
8-digit display 6-digit display 4-digit display
ERROR-xx ERR-xx E-xx
(2) Error Code List
Code Class Displayed error code Description of the code and potential cause(s)
10 Electricity Carriage Home NG CRG can't be moved to inner diameter.
SERVO LSI Com- CRG can't be moved from inner diameter.
munication Error -> Failure on home switch or CRG move mechanism.
Communication error between microcomputer and SERVO LSI.
11 Electricity Focus Servo NG Focusing not available.
-> Stains on rear side of disc or excessive vibrations on REWRITABLE.
12 Electricity Spindle Lock NG Spindle not locked. Sub-code is strange (not readable).
Subcode NG -> Failure on spindle, stains or damages on disc, or excessive vibrations.
A disc not containing CD-R data is found.
Turned over disc are found, though rarely.
CD signal error.
17 Electricity Setup NG AGC protection doesn't work. Focus can be easily lost.
-> Damages or stains on disc, or excessive vibrations on REWRITABLE.
30 Electricity Search Time Out Failed to reach target address.
-> CRG tracking error or damages on disc.
44 Electricity ALL Skip Skip setting for all track.
(CD-R/RW)
50 Mechanism CD On Mech Error Mechanical error during CD ON.
-> Defective loading motor, mechanical lock and mechanical sensor.
A0 System Power Supply NG Power (VD) is ground faulted.
-> Failure on SW transistor or power supply (failure on connector).
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors).
Unreadable TOC does not constitute an error. An intended operation continues in this case.
Upper digits of an error code are subdivided as shown below:
Check the following signal in theAV unit.(BSEN/ASEN/ILM, 8 V Powersupply)
Key illumination is
lighted more than 20
seconds?
LCD backlight is OK?
NAVI5V is OK?
Check the Power supply (D/Dconverter) block and Control signal(48pin NAVICON) of the Systemu-com in the AV unit.
LCD unit failure.Power supply
block for "LCD Panel
unit" is OK?
LCD Panel unit failure.NAVI unit failure.
NAVI3V from theNAVI unit is OK?
NAVI unit failure.(NAVI3V is supplied from NAVIunit and also NAVI3V isgenerated from NAVI5V)
NO
YES
NO
YES
NO
(No output)
YES
NO
Key illiminationgo off after 20seconds.
Initial communication errorbetween NAVI and AV unit.- Confirm communication line between 2 unit. (*1)- Change the NAVI unit
(*1)Normal operation after ACC ON- RESETB: High- OFFINFO: L -> H- OFFANS: H -> L- CTOSYS: UART- SYSTOC: UART- CPUWDT: L- BATFAULT: L
Notes:All siganl mentioned above are controlkey signal from System u-com (AVunit) to NAVI unit.The "H" voltage is different depends onthe location. - Port of system u-com: 5 V - Connector of AV unit: 3 V
YES
No Display(White or Gray screen)
YES
NO
(No output)
NO
YES
- FLOWCHART
AVIC-F700BT/XS/UC401 2 3 4
C
D
F
A
B
E
5 6 7 8
LCD BD Side ANAVI BD Side BNAVI BD Side A
Case 1 System can not wake-up.
ACC ON ACC OFFPin27: NAVI33V High High This power supply is from NAVI BD to AV BD.Pin5: OFFINFO High Low This signal is from AV BD(system-ucom) to NAVI BD.Pin6: OFFANS Low High This signal is from NAVI BD to AV BD(system-ucom).
(High = 3.3 V)Pin13: SYSTOC Communication line (Sys u-com to NAVI unit)Pin14: CTOSYS Communication line (NABI unit to Sys u-com)
Pin3,5,7,9,11,13,15,17,19 ACC ON ACC OFFNAVI 5V 5V 5V power supply is from AV BD to NAVI BD.
Case 2 Navi image can not be displayed on LCD.
Pin1: TFT_ANODEPin36: LVDSN Video signal (LVDS) from NAVI to LCD BD. Pin2: TFT_ANODE2Pin37: LVDSP Video signal (LVDS) from NAVI to LCD BD. Pin6: TFT_CATHODE
Pin7: TFT_CATHODE
Power supplyfrom LCD BD to
LCD unit
05niP1niP
Pin1
Pin2
Pin19
Pin20
Pin1 Pin74
Chip resistor (0 ohm)
A B
CD
E
B
C
D
F
Pin1 Pin10
- DIAGNOSIS POINT
AVIC-F700BT/XS/UC 415 6 7 8
C
D
F
A
B
E
1 2 3 4
Case 3 Touch panel operation doesn't work
Pin1: nYPONPin2: nXPONPin3: YMONPin4: XMON
Pin29: nYPONPin30: nXPONPin31: YMONPin32: XMON
Case 4 Hard Key doesn't work
Pin8: KEY0 KEY (Push, Menu, Right) signal from KEY BD to LCD BD (DC Voltage)Pin9: KEY1 KEY (MAP, Left, Down ,Up) signal from KEY BD to LCD BD (DC Voltage)Pin11: ROT0 KEY (Rotary) signal from KEY BD to LCD BD (Pulse waveform)Pin12: ROT1 KEY (Rotary) signal from KEY BD to LCD BD (Pulse waveform)
Pin33: ROT0 KEY (Rotary) signal from KEY BD to LCD BD (Pulse waveform)Pin34: ROT1 KEY (Rotary) signal from KEY BD to LCD BD (Pulse waveform)
The signal from touch-panel to LCD BD(Wavefrom pulse can be mintored while operating touch-panel.)
The signal from LCD BD to NAVI BD(Wavefrom pulse can be mintored while operating touch-panel.)
Pin1 Pin4
Pin1 Pin74
Pin1 Pin74
05niP1niP
E
A
D
B
AVIC-F700BT/XS/UC421 2 3 4
C
D
F
A
B
E
5 6 7 8
Case 5 Audio (NAVI SOURCE) or Guide voice (BEEP sound) is NG.
Pin19: GUI_P Guidance or BEEP sound Pin28: NAVI L Audio Lch Pin30: NAVI R Audio RchPin29,31: GND
05niP1niPB
AVIC-F700BT/XS/UC 435 6 7 8
C
D
F
A
B
E
1 2 3 4
6. SERVICE MODE6.1 TEST MODE
1. Test mode menu selection method
The main keyboard cannot be used for this operation. Double-click the touch panel directly.
2. Test mode activation method
1. Copy a "TestMode" folder under “TestMode” folder on GGV1322 to a SD card. Note: "TestMode" folder must be on the SD card root. 2. Download a ID file from the Service Site and copy the file to the "TestMode" folder on the SD card. 3. Insert the SD card into the main unit. 4. Turn ACC ON. 5. The test mode menu is displayed.
<< Enter the test mode in the set procedure. >>
When the set procedure is followed (Procedure OK)
Start screen
Jig No : GGV1322
AVIC-F700BT/XS/UC441 2 3 4
C
D
F
A
B
E
5 6 7 8
3. Test mode menu
No. Test Item Test Content 1 Audio Playback of audio 2 AV Test Not for service 3 TEL Test Not for service 4 GPS CHK GPS receiver test 5 GYRO Not for this model (F900 series only) 6 Flash ROM Flash ROM read/write test 7 TMC/VICS FM multiplex error test 8 Dir CMD Not for service 9 Graphics Graphics test 10 Ver Info Display version information of software, mecha, and microcomputers. 11 Touch Correction and test of Touch Panel 12 Key Test Not for service 13 Port Test Display states such as parking and reverse. 14 Voice Test Not for service 15 Memory Not for service 16 MSN-Direct Not for service 17 USB Test Not for service 18 DTV Test Not for service 19 SD Test SD card test 20 EQ Flat/Vo Not for service 21 RGB Illumin Not for service 22 BT Test Not for service 23 Screen Not for service 24 BAK CTL Adjustment of the LCD backlight
<< Operation method >>1. Select ‘Start Type’. Normally, ‘Hot’. 2. Press ‘Start’ to start the test.
AVIC-F700BT/XS/UC461 2 3 4
C
D
F
A
B
E
5 6 7 8
Tracking
Signal
<< Operation method >>1. When GPS Running is red, press ‘hot’.
<< Operation method >>1. When GPS Running is green, the test is started.2. When Valid Position is green, the measurement is successfully conducted.
<< Operation method >>1. The screen will be in this state if the test is not started.2. To start the test, press ‘hot’.
AVIC-F700BT/XS/UC 475 6 7 8
C
D
F
A
B
E
1 2 3 4
Sats
<< Operation method >>1. The screen will be in this state if the test starts.2. When the blue color bar appears, GPS signal is locked.
<< Operation method >>1. The screen will be in this state if the test is not started.2. To start the test, refer to ‘Start test’ tab.
<< Operation method >>1. When the test starts and a satellite is started to be acquired, the screen will be in this state.Red • • • Not acquired. Yellow • • • Already acquired. Green • • • Acquired and data obtained.
AVIC-F700BT/XS/UC481 2 3 4
C
D
F
A
B
E
5 6 7 8
NAND Flash test mode start screen
Write files Conduct a write test to NAND Flash disc.
Read/verify files Conduct a read test to NAND Flash disc. Notes) It will take time by test completion.
Delete Files Conduct a deletion test to NAND Flash disc.
Format disc Conduct a formatting test to NAND Flash disc. Notes) Only the test area of the Flash disc will be formatted.
GpsTmcDemo
TMC measurement selection screen
<< Test Content >>The TMC error rate can be measured.The frequency can be changed by tapping ‘<’ or ‘>’.The test can be terminated by tapping the left ‘x’ mark.
AVIC-F700BT/XS/UC 495 6 7 8
C
D
F
A
B
E
1 2 3 4
Graphics Test start screen
Start screen
<< Operation method >>1. The screen will be in this state after started.2. Press ‘Test’ to start the test.
<< Operation method >>1. The menu appears when ‘Test’ is pressed. Select the item to test.
<< Operation method >>1. To terminate the test, press ‘File’ and then ‘Exit’.
AVIC-F700BT/XS/UC501 2 3 4
C
D
F
A
B
E
5 6 7 8
Version Information screen
Touch Panel Test screen
Start screen
Start screen
<< Key operation >>[Get Version] • • • Display the version of Bootloader, GPS, and BSP.
[Get Application Version] • • • Display the version of each application.
[uCOM Ver] • • • Display the microcomputer version and ROM Collection version.[Get DVD-Mecha] • • • Display the DVD and CD mecha version.[Clear] • • • Clear the display of the version of microcomputer, ROM, and mecha.
<< Key operation >>Touch panel calibration can be conducted by tapping five ‘+’ marks.
<< Key operation >>A line appears when a line is drawn by a finger on the touch panel.The test can be terminated by pressing the top right ‘x’ mark.
AVIC-F700BT/XS/UC521 2 3 4
C
D
F
A
B
E
5 6 7 8
Port Test screen
SD Card Test screen
Start screen
Start screen
<< Key operation >>[Start] • • • Start the test.
<< Key operation >>[Get signal] • • • Display the states of Parking brake, Reverse, K-Mode, and Speed Pulse.The states of Illumination, Cellular mute, OPTSNS, Antenna control, and Remote control are displayed automatically.
[Clear] • • • Clear the display.
[High] • • • Not for service[Low] • • • Not for service
AVIC-F700BT/XS/UC 535 6 7 8
C
D
F
A
B
E
1 2 3 4
Backlight Test screen
Error screen
Start screen
<< Key operation >>[Backlight Off] • • • The backlight turns off. Notes) No operation can be conducted after this operation. Make a recovery by turning ACC OFF ON.[Backlight on] • • • The backlight turns on.[Set] • • • The brightness of the backlight can be changed.
This is the state when an error occurred in the test.
AVIC-F700BT/XS/UC541 2 3 4
C
D
F
A
B
E
5 6 7 8
<< Key operation >>3. When the keyboard appears, tap the edit box again to make it active. Then input by keyboard becomes possible.
Enter a desired number and tap ‘Set’ to change the brightness of the backlight.
Backlight Level setting method
<< Key operation >>1. Tap the edit box at the left of the Set button to make it active.2. Then, tap the bottom left of the screen, and the screen will be as shown below. Tap ‘Keyboard’.
AVIC-F700BT/XS/UC 555 6 7 8
C
D
F
A
B
E
1 2 3 4
6.2 CD TEST MODE
1) Cautions on adjustments In this product the single voltage (3.3 V) is used for the regulator. The reference voltage is the REFO1 (1.65 V) instead of the GND.If you should mistakenly short the REFO1 with the GND during adjustment, accurate voltage will not be obtained, and the servo’s misoperation will apply excessive shock to the pickup. To avoid such problems:a. Do not mix up the REFO1 with the GND when connecting the (-) probe of measuring instruments. Especially on an oscilloscope, avoid connecting the (-) probe for CH1 to the GND. b. In many cases, measuring instruments have the same potential as that for the (-) probe. Be sure to set the measuring instruments to the floating state.c. If you have mistakenly connected the REFO1 to the GND, turn off the regulator or the power immediately.
Before mounting and removing filters or leads for adjustment, be sure to turn off the regulator.
For stable circuit operation, keep the mechanism operating for about one minute or more after the regulator is turned on.
In the test mode, any software protections will not work. Avoid applying any mechanical or electrical shock to the mechanism during adjustment.
The RFI and RFO signals with a wide frequency range are easy to oscillate. When observing the signals, insert a resistor of 1k ohms in series.
The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it.
2) Test modeThis mode is used to adjust the CD mechanism module. To exit from the test mode.Turn off the ACC and back up.
Notes:a. During ejection, do not press any other keys than the EJECT key until the loaded disc is ejected.b. If you have pressed the (→) key or (←) key during focus search, turn off the power immediately to protect the actuator from damage caused by the lens stuck.c. For the TR jump modes except 100TR, the track jump operation will continue even if the key is released.d. For the CRG move and 100TR jump modes, the tracking loop will be closed at the same time when the key is released.e. When the power is turned off and on, the jump mode is reset to the single TR (91), the RF amp gain is set to 0 dB, and the auto-adjustment values are reset to the default settings.
AVIC-F700BT/XS/UC561 2 3 4
C
D
F
A
B
E
5 6 7 8
WMM-14-23-01 E RE UC AU J CN PKB
(1), (2) and (3) are invisible buttons
In this screen, press long the areas (1), (2) and (3) that display the test mode selection screen by implementing the operations below in order.
Detailed procedureStep1 change the screen to source OFF screenStep2 press the area of (1) longStep3 press the area of (2) longStep4 press the area of (3) long
* When the operation above is normally implemented, BEEP sound 1 is output.
If the operation is completed successfully, the screen shifts to test mode screen after (3) is pressed long
The test mode is released by ACC-OFF operation.
Source PlateOFF
SlaveTestMode
DVD(CD) region display
DVD(CD) debug display
DVD(CD) touch direct display
Back
Shift to selected test mode.
Map
AVIC-F700BT/XS/UC 575 6 7 8
C
D
F
A
B
E
1 2 3 4
[Key]
Contents
Display
Test Mode In
Source On
TRK MIN SEC
[07]
Power On(T.Offset is adjusted)TRK MIN SEC00 00 00
[03]
Power On(T.Offset is not adjusted)
99 99 99
[02]
RF AMPGain switching
GG GG GG
*1[04]
SPINDLESpeed switching
SP SP SP
*9
[03]
Focus CloseS curve check
TRK MIN SEC91 91 91
[06]
Focus Mode switching
0X 0X 0X
*2
[01]
Tracking ServoClose
00 00 00or 99 99 99
[08]
CRG +
[02]
Self-adjustingswitching
TRK MIN SEC?? ?? ??
*3*8
[09]
CRG -*8
[07]
Power Off
TRK MIN SEC
[07]
Power Off
TRK MIN SEC
[07]
Power Off
TRK MIN SEC
[07]
Power Off
TRK MIN SEC
[01]T.Close & AGC
Applicable servomechanism
TRK MIN SEC?tr ?min ?sec
[06] [03]
RF AGC /RF AGC coefficient display
[08]
CRG +
8X 8X 8Xor 9X 9X 9X
[02]
T.Balance adjustment /T.BAL coefficient display
TRK MIN SEC?? ?? ??
[09]
CRG -T.CloseApplicable servomechanism
?? ?? ??
[01]
F,T,RF AGCF.Bias display switchingTRK MIN SEC
TRK MIN SEC
TRK MIN SEC
TRK MIN SEC?tr ?min ?sec
TRK MIN SEC
[03] [06]
CRG/TR jumpvalue switching
[08]
CRG/TR Jump +
[02]
Tracking Open
[09]
CRG/TR Jump -
?tr ?min ?sec
TRK MIN SEC
TRK MIN SEC
TRK MIN SEC?tr ?min ?sec
00 00 00or 99 99 99
TRK MIN SEC
TRK MIN SEC?tr ?min ?sec
8X 8X 8Xor 9X 9X 9X
8X 8X 8Xor 9X 9X 9X
00 00 00or 99 99 99
TRK MIN SEC?tr ?min ?sec?? ?? ??
*7 F,T AGC / F.BiasRF AGC
8X 8X 8Xor 9X 9X 9X
[02]
Tracking Open
*6
*5
*4 *4
Operation[Key] Test Mode
[07] Power On/Off[08] CRG + / TR Jump +
(Direction of the external surface)[09] CRG - / TR Jump -
(Direction of the internal surface)[01] T. CLS & AGC & Applicable servomechanism /
[6] F. Mode switching / Tracking Close / CRG•TRJump Switching
*) • After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete.• When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
sticks to Wall, causing the actuator to be damaged).• In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.
*10
TRK MIN SEC
[05]
Gop ModeGop Mode switching
OL OL OL
- Flow Chart
*1) TYP → + 6 dB → + 12 dB TRK MIN SEC TRK06MIN06SEC06 TRK12MIN12SEC12
*2) Focus Close → S Curve check setting → F EQ measurement setting TRK00MIN00SEC00
TRK01MIN01SEC01 TRK02MIN02SEC02 (TRK99MIN99SEC99)
*3) F.Offset Display → RF.Offset → T.Offset Display → Switch to the order of the original display
TRK22MIN22SEC22 TRK11MIN11SEC11*10) OFF(TYP) → FORCUS → TRACKING TRK MIN SEC
TRK70MIN70SEC70 TRK71MIN71SEC71
• As for the double speed (2x), audio output cannot be supported
AVIC-F700BT/XS/UC581 2 3 4
C
D
F
A
B
E
5 6 7 8
6.3 uBOOT MENU
UBOOT Upgrade
1. Copy the Uboot files named as “uboot.bin” and “uboot.cks” to the SD/MMC card2. Inset SD/MMC card to the Main Unit at first, then enter the Uboot interface.3. Select ““3=UBOOT Upgrade” item in Uboot menu, then select ““1=UBOOT by SD/MMC” item in “UBOOT Upgrade” menu and execute.
UBOOT Upgrade
0=WINCE Upgrade 0=UBOOT by USB1=GPS Tools 1=UBOOT by SD/MMC2=BT Tools 2=Exit3=UBOOT Upgrade Choice: 14=Memory Tools5=Other ToolsCoice: 0
<Uboot Menu> <UBOOT Upgrade Menu>
UBOOT Upgrade UBOOT Upgrade
0=UBOOT by USB 0=UBOOT by USB1=UBOOT by SD/MMC 1=UBOOT by SD/MMC2=Exit 2=ExitChoice: 1 Choice: 1
Star Erase & Write UT!!UT Upgrade OK
Star Erase & Write UT!! Please restart your device!!Read Progress : 31% Read process 100%
4. After the menu of “UBOOT Upgrade” show “UT Upgrade OK”, restart the device.
WINCE Image Upgrade
1. Copy the image files named as “winceimg.bin” and “winceimg.cks” to the SD/MMC card.2. Inset SD/MMC card to the Main Unit at first, then enter the Uboot interface.3. Select “0=WINCE Upgrade” item in Uboot menu, then select “1=WINCE bySD/MMC” item in “WINCE Upgrade” menu and execute.
WINCE Upgrade
0=WINCE Upgrade 0=WINCE by SD/MMC (Format)1=GPS Tools 1=WINCE by SD/MMC2=BT Tools 2=WINCE by USB (Format)3=UBOOT Upgrade 3=WINCE by USB4=Memory Tools 4=Exit5=Other Tools Coice: 1Coice: 0
<Uboot Menu> <WINCE Upgrade Menu>
WINCE Upgrade WINCE Upgrade
0=WINCE by SD/MMC (Format) 0=WINCE by SD/MMC (Format)1=WINCE by SD/MMC 1=WINCE by SD/MMC2=WINCE by USB (Format) 2=WINCE by USB (Format)3=WINCE by USB 3=WINCE by USB4=Exit 4=ExitCoice: 1 Coice: 1
Image RegionChecksum = 0x64463447
Read Progress : 31% CE Upgrade OKPlease restart your device!!
4. After the menu of “WINCE Upgrade” show “CE Upgrade OK”, restart the device.
AVIC-F700BT/XS/UC 595 6 7 8
C
D
F
A
B
E
1 2 3 4
6.4 USING THE TEST DISC
Test Disc 1 Start Screen Specification
Test Disc 1 Start
1. Copy all files under “Test Disc1” folder on GGV1322 to a SD card. 2. Download a ID file from the Service Site and copy the file to the SD card. 3. Insert the Test Disc in the SD card and turn ACC OFF ON. Then, the test disc starts. The test can be terminated by turning ACC OFF. After turning ACC OFF, remove the SD card.
Test Disc 1 Start Screen
MIC Test
<< Operation method >>1. This screen appears when the Test Disc is activated.2. Tap ‘E-MIC’ to start the test.
<< Operation method >>1. This screen appears when the test is started.2. Put a sound into the microphone while this screen is shown. The sound is recorded.
Jig No : GGV1322
AVIC-F700BT/XS/UC601 2 3 4
C
D
F
A
B
E
5 6 7 8
<< Operation method >>1. When this screen appears, the recorded sound is played ‘loudly’.Notes) The sound volume cannot be adjusted.
<< Operation method >>1. When this screen appears, the recorded sound is played ‘quietly’.Notes) The sound volume cannot be adjusted.
<< Operation method >>1. When this screen appears, the recorded sound is muted.Notes) The sound volume cannot be adjusted.
AVIC-F700BT/XS/UC 615 6 7 8
C
D
F
A
B
E
1 2 3 4
<< Operation method >>1. When the test finishes, this screen appears.2. To proceed to the next test, tap ‘OK’. To conduct MIC Test again, tap ‘Retry’.
<< Operation method>>1. This screen appears when the Test Disc is activated.If you tap "GPS_TTFF", the test is started.
GPS Test
<< Operation method >>1. When the test is started, this screen is displayed.When you terminate the test in the way, tap the "Exit".
AVIC-F700BT/XS/UC621 2 3 4
C
D
F
A
B
E
5 6 7 8
<< Operation method >>When the positioning is terminated within one minute, the test is completed successfully, and this screen is displayed.If you implement the test again, tap the "Retry".If you go to next step, tap "OK".
Version Check
<< Operation method >>1. This screen appears when the Test Disc is activated. 2. When ‘Version’ is tapped, the test starts. If the "Reality" corresponds to "Plan", the result becomes "OK".
AVIC-F700BT/XS/UC 635 6 7 8
C
D
F
A
B
E
1 2 3 4
<< Operation method >>If the test result is "OK", the blue screen is displayed."Reality" is each version on actual machine and the "Plan" is the version information described in "Information.txt" of SD card.
<< Operation method >>If the test result is "NG", the red screen is displayed.
AVIC-F700BT/XS/UC641 2 3 4
C
D
F
A
B
E
5 6 7 8
Test Disc 2 Start Screen Specification
Test Disc 2 Start
1. Copy all files under “Test Disc 2” folder on GGV1322 to a SD card. 2. Download a ID file from the Service Site and copy the file to the SD card. 3. Insert the SD card into the Main Unit and turn ACC OFF ON. Then, the test disc starts.
The test can be terminated by turning ACC OFF. After turning ACC OFF, remove the SD card.
Test Disc 2 Start Screen
The user data is deleted
<< Operation method >>1. This screen appears when the Test Disc is activated.2. If you tap the "Restore", the user data is deleted.
<< Operation method >>If the deletion is terminated, this screen is displayed.
Jig No : GGV1322
Notes:) "Splash screen setting" is not back to default after performing this function. Please set the "Splash screen setting", before performing this function.
AVIC-F700BT/XS/UC 655 6 7 8
C
D
F
A
B
E
1 2 3 4
7. DISASSEMBLY
1 1 1
Fig.1
Removing the Case (Fig.1)
Remove the two screws and then removethe Case.
Note)To remove the screws, use jig No. GGK1068.
Case
NOTE) While the photograph shown is slightly different from this model in shape, the disassembly procedure is the same.
1
1
1
1
1
Fig.2
Remove the four screws.
Disconnect the connector on the back and then remove the CD Mechanism Module.
Removing the CD Mechanism Module (Fig.2)
CD Mechanism Module
AVIC-F700BT/XS/UC661 2 3 4
C
D
F
A
B
E
5 6 7 8
1
21 2
1
1
112
2
Fig.4
Remove the five screws.
Disconnect the four connectors and thenremove the Navi Unit.
Removing the Navi Unit (Fig.4)Navi Unit
1
2
3
(Right side)
2
1
1
1
3
2
33
1
1
1
(Top side)
(Left side)
Fig.3
Removing the Monitor Assy (Fig.3)
Remove the six screws.
Release the two latches.
Disconnect the three connectors and thenremove the Monitor Assy.
Monitor Assy
Monitor Assy
Monitor Assy
2
AVIC-F700BT/XS/UC 675 6 7 8
C
D
F
A
B
E
1 2 3 4
1
2
3
Remove the screw.
Remove the six screws and then removethe AV Unit.
5
6
4
6
6
2
6
5
2
4
66
2
2
3
22
1 1
2
4 4
6
(Right side)
(Left side)
Fig.5
Remove the two screws.
Remove the seven screws.
Disconnect the connector and thenremove the Heat Sink.
Remove the three screws and thenremove the Chassis(Upper).
Removing the AV Unit (Fig.5)
AV Unit
Chassis(upper)
Chassis(Upper)
Heat Sink
Remove the FFC(CDE8550).
Remove the FFC(CDE8552).
Remove the cord assy(CDE8393).
Remove the cord assy(CDH1381).
AVIC-F700BT/XS/UC681 2 3 4
C
D
F
A
B
E
5 6 7 8
1
2
3
1
2
3
1
3 3
3
22
3 3
2 2 2
2
2
SD Unit
3
2
3
3
3
1
1
12
1
Fig.6
Fig.7
Removing the Panel Unit (Fig.6)
Removing the Keyboard Unit (Fig.7)
Panel Unit
LCD Module Assy
Keyboard Unit
Remove the four screws.
Release the five latches and then removethe LCD Module Assy.
Remove the four screws and then removethe Keyboard Unit.
Remove the screw and connectorand then remove the SD Unit.
Disconnect the four connectors.
Remove the five screws and then removethe Panel Unit.
1
AVIC-F700BT/XS/UC 695 6 7 8
C
D
F
A
B
E
1 2 3 4
A
A
B
B
Upper Frame
Lower Frame
B
B
B
B
a
Damper
Carriage Mechanism
Damper
Do not squeeze this area.
- How to hold the Mechanism Unit
- Removing the Upper and Lower Frames1. With a disc inserted and clamped in the
mechanism, remove the two Springs (A), the six Springs (B), and the four Screws.
2. Turn the Upper Frame using the part "a" as a pivot, and remove the Upper Frame.
3. While lifting the Carriage Mechanism, remove it from the three Dampers.
Caution: When assembling, be sure to apply some alcohol to the Dampers and assemble the mechanism in a clamped state.
1. Hold the Upper and Lower Frames.2. Do not hold the front portion of the Upper
Frame, because it is not very solid.
AVIC-F700BT/XS/UC701 2 3 4
C
D
F
A
B
E
5 6 7 8
Screw
Shorting Solder
CD Core Unit
Solder
Chassis
Pickup Rack
Pickup
Poly Washer Change Arm
Pickup Lock Arm
Feed Screw
Planet Gear
Inner Holder
- How to remove the CD Core Unit1. Apply Shorting Solder to the flexible cable of
the Pickup, and disconnect it from the connector.
2. Unsolder the four leads, and loosen the Screw.
3. Remove the CD Core Unit.Caution: When assembling the CD Core Unit,
assemble it with the SW in a clamped state so as not to damage it.
- How to remove the Pickup Unit1. Make the system in the carriage mechanism mode, and have it clamped.2. Remove the CD Core Unit and remove the leads from the Inner Holder.3. Remove the Poly Washer, Change Arm, and Pickup Lock Arm.4. While releasing from the hook of the Inner Holder, lift the end of the Feed Screw.Caution: When assembling, move the Planet Gear to the load/eject position before setting the Feed Screw in the Inner
Holder.Assemble the sub unit side of the Pickup, taking the plate (Chassis) in-between. When treating the leads of the Load Carriage Motor Assy, do not make them loose over the Feed Screw.
AVIC-F700BT/XS/UC 715 6 7 8
C
D
F
A
B
E
1 2 3 4
• Notes on disassembly
• When separating the MONITOR ASSY from the MAIN UNIT ASSY, do so slowly. Two FFCs (CDE8554, CDE8556) and one CODE ASSY (CDE8559) are connected. The strength of the joint part of the code and terminals of CDE8559 (CODE ASSY for Bluetooth to connect the keyboard unit and navi unit) is weak, it may break or the code may extend.
Remove after peeling off the tape of CDE8556 and the shield.
• When demounting LCD PANEL ASSY from the grille, be careful not to bend LCD plate (CND4319) as there are snap fits on the right and left. Demount LCD PANEL ASSY by extending snap fits on the grille side.
CDE8559
Snap fit2 place
Do not bend CND4319
Remove snap fits by extending them on the grille side using tweezers or bamboo tweezers.
Do not bend CND4319
Actually does the CODE ASSY (CDE8559) to a left connector of a round inclosing. *
AVIC-F700BT/XS/UC721 2 3 4
C
D
F
A
B
E
5 6 7 8
• Be sure to remove the MONITOR ASSY after removing the CD mecha. If the procedure is done oppositely, the FFC (CDE8556) connecting the MONITOR ASSY and the MAIN UNIT ASSY will be damaged. At assembly, be sure to fix the MONITOR ASSY first and then fix the CD mecha. If it is done oppositely, the FFC (CDE8556) cannot be folded as intended under the CD mecha.
• When connecting the code assy connecting 1F AV UNIT and 2F NAVI UNIT (CDH1381) on NAVI UNIT side, do so as shown below.
• The code assy connecting 1F AV UNIT and 2F NAVI UNIT (CDE8393) shall be fitted on the back side of the choke coil (CTH1347) after 1F Chassis Unit and 2F Chassis Unit are fixed, as shown below.
CDE8556
OKHorizontal
NGVertical
CDE8393
CTH1347
AVIC-F700BT/XS/UC 735 6 7 8
C
D
F
A
B
E
1 2 3 4
• When mounting KNOB ASSY (CXC8994, CXC8995) in the MONITOR ASSY, be careful to don't destroy encoder part.
• Since two case (CNB3472) fixing screws are ‘TORX tamper’ (tamper-proof screws with a projection in TORX), a special tool is required.TORX screwdriver(T8) : GGK1068
CSX1135 shaft of an encoder CXC8994 CXC8995
Mark 1 (T8 size)
M2.6 thread
AVIC-F700BT/XS/UC741 2 3 4
C
D
F
A
B
E
5 6 7 8
8. EACH SETTING AND ADJUSTMENT8.1 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT
CD CORE UNIT(S10.5COMP2)
Note :The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the PU unit must be changed, the grating should be checked using the procedure below.
Purpose :To check that the grating is within an acceptable range when the PU unit is changed.
Symptoms of Mal-adjustment :If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform track search operations, or taking a long time for track searching.
Method :
Measuring Equipment Measuring Points
Oscilloscope, Two L.P.F. E, F, REFO1
Disc TCD-782 Mode TEST MODE
Checking Procedure1. In test mode, load the disc and switch the 3 V regulator on.2. Using the key 08 and key 09, move the PU unit to the innermost track.3. Press key 03 to close focus, the display should read "91". Press key 02 to implement the tracking balance adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the fourth press.4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase difference is within 75 degrees. Refer to the photographs supplied to determine the phase angle.5. If the phase difference is determined to be greater than 75 degrees try changing the PU unit to see if there is any improvement. If, after trying this a number of times, the grating angle does not become less than 75 degrees then the mechanism should be judged to be at fault. NoteBecause of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle.
HintReloading the disc changes the clamp position and may decrease the "wobble".
100 kohm
390 pF
100 kohm
390 pF
E
VREF
F
VREF
Xch Ych
L.P.F.
L.P.F.
Oscilloscope
FE
REFO1
AVIC-F700BT/XS/UC 755 6 7 8
C
D
F
A
B
E
1 2 3 4
Grating waveform
45 degrees
0 degrees
75 degrees
60 degrees
30 degrees
90 degrees
Ech → Xch 20 mV/div, ACFch → Ych 20 mV/div, AC
AVIC-F700BT/XS/UC761 2 3 4
C
D
F
A
B
E
5 6 7 8
8.2 AV UNIT ADJUSTMENT
- Adjustment pointAV UNIT(SIDE A)
AV UNIT(SIDE B)
VR4231
V1VG(GND)
V1V
FRV
FRG
1
CN1016AV CONNECTOR
AVIC-F700BT/XS/UC 775 6 7 8
C
D
F
A
B
E
1 2 3 4
AV
UN
ITA
DJU
ST
ME
NT
Step
Adj
ustm
ent
item
Mod
eIn
puts
igna
l(In
putt
estp
in,s
pecs
,ot
herc
ondi
tions
)
Out
puts
igna
l(M
easu
rem
ent p
oint
,wav
e pa
ttern
)M
asur
ing
inst
rum
ents
Spec
sA
djus
ting
poin
t
1V
ideo
leve
lad
just
men
tA
Vse
lect
orV
TR1
TPV
1V, V
1VG
(GN
D)
100
IRE
(whi
te10
0%)
1.0
Vp-
p(In
putv
ia75
ohm
)
Mea
sure
men
tpoi
nt:
FRV
FRG
(GN
D)
(To
mea
sure
the
AVU
nit o
nly,
conn
ect
1.4
kohm
betw
een
TPFR
Van
dFR
G.)
Osc
illosc
ope
1.00
V±
0.02
Vp-
p
Mea
sure
betw
een
the
sync
tipan
d10
0IR
E(w
ave
top)
.
Sym
ptom
sw
ithpo
orad
just
men
t.O
verl
evel
:Lu
min
ance
isto
ohi
gh.
Und
erle
vel:
Lum
inan
ceis
too
low
.
VR42
31
AVIC-F700BT/XS/UC781 2 3 4
C
D
F
A
B
E
5 6 7 8
8.3 FLICKER ADJUSTMENT
FLIC
KER
AD
JUST
MEN
T
Adj
ustm
enti
tem
Mea
sure
men
tpoi
ntA
djus
tmen
t poi
ntTh
eco
nten
tsof
adju
stm
ent
Rem
arks
.langis%001
etihwtupnI
gnigA
1Le
ave
form
ore
than
30m
inut
esin
oper
atio
nm
ode.
2Fl
icke
radj
ustm
ent
Scr
een
LCV
R1
Adj
ustt
hefli
cker
leve
lto
min
imum
from
all
dire
ctio
ns.
Sig
nalf
or F
licke
radj
ustm
ent…
Sel
ect “
Gra
phic
s” ->
“Fl
icer
Adj
ustm
ent”
in th
e Te
st M
ode.
(In
puta
sign
alfo
r al
tern
ate
whi
te a
ndbl
ack
line.
The
lum
inan
cele
velo
fthe
inpu
tsig
nal:
50%
)
AVIC-F700BT/XS/UC 795 6 7 8
C
D
F
A
B
E
1 2 3 4
9. EXPLODED VIEWS AND PARTS LIST
9.1 PACKING
NOTES : Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.)
""
AVIC-F700BT/XS/UC801 2 3 4
C
D
F
A
B
E
5 6 7 8
(1) PACKING SECTION PARTS LIST
(2) CONTRAST TABLEAVIC-F700BT/XS/UC, AVIC-F7010BT/XS/UC and AVIC-F700BT/XS/EW5 are constructed the same except for the following:
Installation Manual
Mark No. Description Part No.
1 Unit Box See Contrast table(2)
2 Contain Box See Contrast table(2)
3 Protector See Contrast table(2)
4 Protector See Contrast table(2)
5 Screw Assy See Contrast table(2)
6 Screw BMZ50P060FTC
* 7 Polyethylene Bag CEG-127
8 Screw See Contrast table(2)
9 Polyethylene Bag CEG1116
10 Sub Unit Box CHG6491
11 Connector CKX1049
12 Seal CNN2515
13 Pen CNV8969
14 CD-ROM See Contrast table(2)
15 Microphone Assy CPM1064
16 Clip Holder CZN5471
17 Microphone Holder CZN5472
18 Cushion CZN5473
* 19 Microphone CZX5059
20 GPS Antenna Assy CXC8574
21 Attachment Assy CEA4636
22 Water Proof Pad CZN7150
23 Sheet CZN7151
24 •••••
25 Polyethylene Bag See Contrast table(2)
26 Panel See Contrast table(2)
27 Cord CDE6825
28 Cord Assy See Contrast table(2)
29 Cord Assy See Contrast table(2)
30 Cord Assy See Contrast table(2)
31-1 Installation Manual See Contrast table(2)
31-2 Caution Card See Contrast table(2)
* 31-3 Registration Card See Contrast table(2)
* 31-4 Warranty Card See Contrast table(2)
31-5 Owner's Manual See Owner’s manual parts list(3)
* 31-6 Passport See Contrast table(2)
* 31-7 Caution Card See Contrast table(2)
Mark No. Description Part No.
Mark No. Description AVIC-F700BT/XS/UC AVIC-F7010BT/XS/UC AVIC-F700BT/XS/EW5
Decimal points for resistorand capacitor fixed valuesare expressed as :2.2 t 2R20.022 t R022
Symbol indicates a resistor.No differentiation is made between chip resistors anddiscrete resistors.
NOTE :
Symbol indicates a capacitor.No differentiation is made between chip capacitors anddiscrete capacitors.
to NAVI UNITSPJ1
AVIC-F700BT/XS/UC921 2 3 4
C
D
F
A
B
E
VIC
SO
N
AN
TO
N
A
NF
CO
NT
C28
04R
1
R
R28
0410
0K
AS
EN
S
-V5
R
AN
TO
N
VIC
SO
N
16 17 18 19
C28
33
R1
C28
23
R1
GND
NF
CO
NT
NA
VI5
V
NA
VI5
V
NA
VG
ND
AV
8V G
ND
5.0V
5.0V
5 6 7 8
1/6A
A-b 1/6
RR
RR+
PKB
FL+
ASENS
FR-
ILMSNS
ANTON
SR
CM
UT
E
FR+
SR
EM
OT
E
REVSNS
FANUP
SREMOTE
OFFMUTE
RL-
FR
FL-
FL
BREMOTE
RL+
RL
RR-
AV
2RS
AS
EN
S
SR
CM
UT
E
GU
IDE
MU
TE
MO
NV
BS
NA
VIL
G
AV
2RG
NA
VIR
G
AV
2LG
AV
2VG
AV
2LS
AV
2VIN
NA
VIA
R
NA
VIA
L
GU
IDE
GU
IDE
G
FR
V
FR
VG
ND
RS
TM
UT
E
KM
OD
EO
UT
FA
NU
P
PK
BO
UT
PK
B
AN
TO
N
ILM
B
ILM
R
ILM
G
PO
MU
TE
BR
EM
OT
E FR
FL
RR
RL
ILM
V
RL+
FL+
FR+
FL-
RL-
SYSPW
FR-
RR+
RR-
KB
UP
SYSPW
DCSKIPCD
NA
VI3
V
V8
AV
8
BU
P
GNDA
R28
814R
7K(1
/4W
)
BUP2
IC1007PAL007C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
FR
Q28
63U
MD
2N
2E1
2B2
1C3
1E45
1B
62C
ILM
G
GNDD
R28
73
4R7K
GND1
AN
TO
N
R29021K
(1/4W)
R29
0110
0K
R29
034R
7K(1
/4W
)
R2875
4R7K(1/4W)
GNDD
D2802B060L-40
DTC114EUAQ2880
C29
32
2R2
(212
5)
GN
DD
GNDD
AV
2LS
GU
IDE
MU
TE
D2862DAN202U
NA
VIR
G
GNDD
GNDD
GNDD
C2926
1
FR
VG
ND
DTC114EUAQ2864
R29
10
47K
33/1
0
C28
62
IC28
90T
PD
1018
F
1O
UT
2G
ND
13
GN
D2
4G
ND
35
VD
D6
IN
7G
ND
4
8G
ND
5
9G
ND
6
10D
IAG
R290047K
ILM
R
L2871
C28
82
R00
1
C28
61R
1
C29
311
Q28
61U
MD
2N
2E1
2B2
1C3
1E45
1B
62C
GNDD
BU
P
C2922
1(2125)
KM
OD
EO
UT
GNDD
C2925
AV
2LG
Q28
60U
MD
2N
2E1
2B2
1C3
1E45
1B
62C
D2860MA111
GNDD
FA
NU
P
GNDD
47/1
6C
2860
KB1
IL1
GNDD
SR
CM
UT
E
L2930
KB
UP
C29
01R
1
CN1005
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1000
0/16
C29
10
3300
/16
C29
35
NA
VIA
L
VD
D5
NA
VIA
R
C28
72
R00
1
C28
90R
1
RS
TM
UT
E
ILM
V
MO
NV
BS
FR
V
C29
24
R1
DTC124EUAQ2865
C2921
C2923
GNDD
AV
2VG
L2872
D2863DAN202U
D2821B060L-40
NA
VIL
G
ILM
B
C28
71
R00
1
C2920
D2900
HZU8R2(B1)
R2870
47K
MUT
GU
IDE
R2874
1K(1/4W)
ISN
GNDD
BR
EM
OT
E
PK
B
PK
BO
UT
D2910KS926S2
FL
AV
2RG
Q28
702S
C41
16
Q28
62
2SC
4081
C28
81 1
C28
92R
001
AV
2RS
D2861UDZS8R2(B)
GNDD
R2880
10K
R2872
1K
AV
2VIN
C28
91R
001
D2890
1SR154-400
C2927
D28
911S
R15
4-40
0
R2865
1K(1/10W)
100/
25C
2929
C29
33 2R2
(321
6)
R28821K
(1/4W)
RR
R28
71
100K
PO
MU
TE
D28
74
PT
Z18
A
R29
2510
K
C2928
20
RL
R29
2410
K
D28801SR154-400
GU
IDE
G
R2926
10K
D2870
UDZS5R1(B)
C28
70
R00
1BUP1
GND2
C29
30R
1
10/1
6C
2934
Q29002SC4116
D29
30
ST
70-2
7F
1000
0/16
C29
11
1000
0/16
C29
12
DTC114EUA
Q2881
2SA1576AQ2882
R28
34
100K
D29
11
RB
060L
-40
R29
12
4R7
R29
13
4R7
D2912KS926S2
GNDD
NK
BU
PR
2911
47K
GNDD
AC2
KB2
RV2
MUB
ACC
AANT
ILM
REV
PLS
PKB
RL-
FL-
RL+
FL+
RR-
FR-
RR+
FR+
SW
VD
D5
R2860
390
R2861
390
R2863
22K
R28
62
47K
R28
64
10K
R2868
220
R28
66
10K
R28
67
10K
R2869
100
R2884
4R7K
R28
83
4R7K
D28
22
DA
N20
2U
D2831RR264M-400
R28
23
1M
NA
VIC
D2825
1SS400G
NA
VI3
V
MTB
A
R2920 0R0
R2921 0R0
R2922 0R0
R2923 0R0
R4802
0R0
R4801
0R0
GNDRF GNDRF GNDRF
PWR AMP
ILM
AANT
ACC
GND
IN4
S-GND
REV
IN2
PKB
PW.GND1
IN1
PW.GND2
TAB
PW.GND4
PW.GND3
VCC1/2
OUT2+
STBY
Vehicle I/F
OUT2-
OUT4-
MUTE
OUT4+
VCC3/4
OUT3-
OUT3+
SVR
OUT1+
OUT1-
PULSE
B_REMOTE
AC GND
IN3
AV8
BUP
AANT
sensing "low voltage"or "reset"
emergency MUTE
AV
8V
1/4W
1/4W
RL+
FL+
RR-
FR-
RL-
RR+
FL-
FR+
AV SECTION
ASENS
ILMSNS
PKB
UCEW5
6.5V
14.4V
14.4V
14.4
V
5.0V
5.0V
5.0V
5.0V
V3.8V3.8
8.3V
600uH
2/6A 6/6A5/6A
6/6A
6/6A AV UNIT(PS/IF SECTION)1/6A
The > mark found on some component parts indicatesthe importance of the safety factor of the part.Therefore, when replacing, be sure to use parts ofidentical designation.
NOTE FOR PCB DIAGRAMS1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic dia- gram.2.Viewpoint of PCB diagrams
1
E
E
E
E
E
1
5
1
1
1
1 101 5 10 15 20 25
1
15
1
5
1
5
10
15
20
1
5
10
1
1
1
510
1 5
10
1
5
1
R601
D3041
R
R606
R
C4201
R3628
C4212
C4213
CN601
C4218
R621
C4219
C4220
ANT1401
R
C4232
C4233
L1403
C603C605
TH601
R4021
R4801
R4802
C4061
C4062
C4063C4064
R4811
R4812
R4813
R4814
R4238
R4815
R4239
R4816 C4070
C4071
C4072
C4073
C4075
C4076
C4078
R4821
C40
79
L1441
Y1461
L1442
L1443
C4080
C2911
D4061
D4062
VR4231
R40
61
R685
R4062
C4288C4289
L472
1
R40
71
R40
72
R4073
R4074
C4291
R4075
Y1481
R4076
L1462
C4293
R4077
R4078
C4294
L1465
C4295
R4079
D2911
R4080
R2912
R2913
C672
L1481
L1482L1483
IC602
C68
5
IC605
R4292
CN1
L7
R4296
L4371
R2941
R2942
CN1015R
2947R
2948
R2949
R2950
CN1021
Q1016
C1406
C1407
C1408
C1409
C1023
IC1000
L3601
IC1008
C430
IC1015
C4314
CN1441
C4316
R1410
R1411
R1412
R1413
C1441
C1442
C1443
C1444C
1445
Q1441
C47
21
C47
22
R1433
C47
23
R1434
C1077
R4318
C1078
C1461
C1462
C1463
C1464
C1465
C1466
R4321
R1441
R1442
R1443
R
R1444R1445
R4
T1401
T1402T1403
C1476
R761
R762
R763
R76R7C1481
R4721
C1482
R47
22
R47
23
C1484
R47
24
C1485
C4171
R47
25
C1486
R47
26
C4173C4175
C4751
C4176
Q4751
Q4752
C4371
C4372
C1494
C1495
C1498
R4164R4166
R4167
R4168
D14
81
C2830
R1481
R1482
R1483
R1484
Q2831
C2835
D47
51
C4199
C2836
Q2832
D47
52
C2837
R4751
R4752
R4753
R4754
R4755
D4371
R4756
R4757
R4758 R1491
R1493
R1495
R1496
R14
98
L603L605
C36
02
C36
03
D2835
C36
05
R2832
C36
06
R28
33
R28
35
L4271
R2836
R2837
R2838
R28
39C3611
C3612
C3613
Q3042
R4794
IC3601
10 20 30 40 50 60 70X
130
120
110
100
90
80
70
60
50
40
30
20
10
0
Y
FR
ANTENNA
FM
/AM
TU
NE
R U
NIT
IP-BUS(UC)
NAVI UNITTMJ1
FU 4631 (A,114,85) Fuse 200 mA CEK1247FU 4641 (A,141,8) Fuse 3.15 A CEK1259FU 4661 (A,136,8) Fuse 2.5 A CEK1258FU 4771 (A,115,106) Fuse 1 A CEK1254
>>>>
WIRED REMOTE
AVIC-F700BT/XS/UC1301 2 3 4
C
D
F
A
B
E
15 20
1
5
D3
C4213
C
C
TH601
C4070
C4071
C4072
C4073
R685
C4288
R40
71
R40
72
4074
4076
CN
C
C4316
RR
C417
R4166
R4167
R4168
71
Q30
70
5 6 7 8
A
SIDE A
E
E
E
E
E
E
E
E
E
E
E
E
1
5
1
5
1
5
1
5
1
5
1
5
1
1
5
10
15
20
25
30
35
40 4550 55606570
75
80
85
90
95
100
105
110115120125130135140
1 1 1
1
1
10
15
20
15
10
15
20
1
5
10
15
20
25
30
35
40
25 30 35 40 45 50
1
10
515
1
15
1
1
10
15
20
25
1
5 10
1
5 10
1
1 5 10 15L2940
C2892
D2870
041
R603
R604
R2870
R3041
R2871
R3042
R3043
R60
7
R608
R3044
C42
08
R613R614
R2880
R615R616
R617
C4210
C4212
R620
D2890
4219
D2891
R622R623
R624
L1004
Q4602
R62
7
4220
R4200
FU4631
C4611
C4612 C4613
R634
C4614
R63
5
R638
FU4641
R64
3R
644
R64
6
D4602
R64
7
C610
X601
C611
C612
R65
0
C4631
R65
1
C617
R653C618
R65
4
Q4631
R65
5
Q4632
R656
R65
7R
658
R65
9
C620
C621
C622
R66
0
R661
FU4661
R66
2
R663
R664
Q4642
C42
62
C42
63C4264
C2900
Q4261
C2901
R670
Q2900
R671
C4651
C4652
C4653 C4654
D4631
R676R677
R4632
R4633
C2910
C2912
R682
R683
R684
D4642
D4643
Q4663
R690
C2924
D2900
C4671
R4262
C4672
R4263
C4673
R694
R4264
R29
00
C4674
C2929
R2901
R2902
R2903
C2930
C2931C2932
C42
97
C2933
R4657
C2934
C2935
C4682
C4685
D4662
C4686 C4687
R4279
L4351
L4352
L704
R2924
L705
R2925
L706
R2926
L707
L708L709
D2930
C68
5
IC606
L710
1000
L711
CN1001
L712
L713
EF4353
L714
EF4354
EF4355
CN1005
EF4356
EF4357
IC610
EF4358
R4686
EF4361
CN1016
Q751
FB701
Q752
Q753 Q754
R2962
R29
63
R29
64
IC1002
IC1007
C4302
R2978
R2979
R2980
R714
R2981
R2982
R717
R2983
R718
C4312
C43134314
CN701
C4315
CN702
C4317
IC1020
C43
18
C4702
R72
2
C4704
C4705
C4708
C4710
R732
C4331
C4332
C4333C4334
C701
C4335C4336
C705
C70
6C70
7 C708
D4701
C709
4318R4319
R43204321
R751
R43
22
IC4703
R43
23
R4324
R43
25
R4326 R43
27R4328
R43
29
C4352
C4353
C2801
C2802
C2803
R764
C2804
R765
L4601
R766
L4602
R767
C4363
C4364
1
C2810
FU4771
C2812Q2811
Q2812
C2820
R4351
D4355
C2821
R4352
D43
56
C2822
D43
57
C2823
C2824
D43
58
D2802
R4163
R4164
R41
65
D4361
D4364
D4365 IC2801
D4368
D2810C4774
C4776
R43
67
R2811
C2840
C28
42
C2843
C2844
Q2841
L4641
D2821
C4786
D2822
L4642
D2823 D2824
D2825R2823
L606
IC2820
L611
L612
L613
L615
C2860C2862
L4661L4662
R2840R2841
R2846
C2870
C3041
C3042
Q2870
Q3041
42
R2852
R2853
C2880
L2930
C2881
Q2880
L4681
L4682
5
5
D43
59
2
80 90 100 110 120 130 140 150 160 170
FRONT
CCN701
NAVI UNITOTJ1
NAVI UNITSPJ1
VEHICLE I/F
AV CONNECTOR
AVIC-F700BT/XS/UC 1315 6 7 8
C
D
F
A
B
E
0
E
1
1
1
R609
611
R61
625
6
R630
632
R636
641
C609
C613
C4252
C4254
1
R4254
251
C2923
R695R697
R
IC
C69
C696
R
C4338
C4339C
4340
C7
IC4702
R4332
R4333
R4335
C2806
R4338
R4339
C4362
R4340
2811
0
R
R4362
R4363
R43646
08
09
R4
1 2 3 4
A
A AV UNIT
170 160 150 140 130 120 110 10
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E E
E
E
E
E
1
15
1
5
1
5
1
1
5
1
5
1
1
1
1
1
5
10
1
1
5
1
5 10
1
10
1
5
10
15
20
1
5
10
15
20
1
5
10
15
20
R2860
R2861
R2862
R2863
R2864
R2865
R2866
R2867
R2868
C2890
R2869
C2891
Q661
D2871
FU460
Q662
D2872
FU4602
D2873
D2874
R605
R2872R2873
R2874
R2875
D2880
R
R2881
R2883 R2884
R619
C4600
C4601
C4602
C4603
C4604
R
C4605
Q4601
R62
C4606
C4607
C4608
R629
C4609
IC2890
C4610
R631
R
R633
C4616
C4617
R637
C4618C4619
R639C601
C604
R640
R
C606
R642
FU4642
R645
D4601
R648
R649
R4601
R4602
R4603
R4604
R4605
R4606
R4607
C614
R4608
R4609IC4601
C616
R652
R4610
C4251
R4611
R4612
C4253
R4613
R4614
R4615
C4641
C4642
FU4662
C4643
C4644
C629
R665
C4645
Q4641 R666
C4646
R667
C4647
R668
C4648
C4261
C4649
C630
C631
C632
C633
R4628
C634
C4650
C4655
C4656C4657
C4658
C4659
R679
R680
R681
R425
C4661
R4252
C4662
R4253
C4663
C4664
R4255
C4665
Q4661
D4641
R686
C4666
Q4662
R687
C4667
Q4664
C4668
IC4
C4669
R4641
R4642
R4643
R4644
R4645
R4646
R4647
C4670
R4648
R691
R4261
R4649
IC4641
R692
R693
C4675
C4676
C4677
C4678
R698
R4650
C4679
R699
R4651
R4652
R4653
R4654
R4655
R4656
D2910
C4681
D2912
C4683
C4684
R2910
R2911
D4661
Q4681Q4682
C4688
R4662
R4663
R4664
R4665
R4666
R4667
R4668
R4669
IC4661
L701
L702
R4670
R4671R4672
R4673
R4674
R4675
EF4731
R4676
EF4732
IC603
EF4733
R4677
R4678
IC604
R4679
IC607
D4681
EF4351
D4682
EF4352
R4680
R4681
R4682 R4683R4684
IC611
R4685
EF4359
IC612
R4687R4688
IC4681
EF4360
R701
R702
R703
R704
R705
R706
R707
R708
R709
R710
R711R712R713
R716
L2870
IC1021
L2871L2872
C4703
C4711
R733
FU4351
FU4352
Q4331
C702
C703
C4337
C704
D4702
R4701
C710
C4731
C4732
Q4731
Q4732
Q4733
Q4734
C4351
Q4738
R4331
R4337
R768
C4361
C
R4343
Q281
D4731
R4346
D4732D
4733
D4734
D4735
R4731
D4736
R4732
D4737
R4733
R4734
D4351
R4735
D4352
R4736
D4353
R4737
R4738
D4354
R4739
D2801
R2801
R2802
R2803
D4360
R2804
D4362
D4363
R4361
C4771
C4772
D4366
C4773
Q601
Q4771
C4775
R436
Q4772Q4773
R2810
Q4774
Q4775
Q4776
C2841
C4784
Q2840
D2820
C4785
R2820
L601
R2821
R2822
L604
L607
L6
R2829
L6
D4771
D4772
D4773
D4774
D4775
R4771
D4776R
4772
R4773
L614
R4774
R4775
R4776
L617
R4777
R4778
C2861
D2840
Q2860
Q2861
Q2862
Q2863Q2864
R2842
R4783
R2843
R4784
R2844
R4785
R2845
R2847
R2848
R2849
C2871
C2872
R2850
R2851
C2882
D2860
Q2881
D2861
Q2882
D2862 D2863
R2882
Q2865
5
5
1
1
FU 2900 (B,71,7) Fuse 250 mA CEK1276FU 4351 (B,116,117) Fuse 40 A MINISMDC075F/24FU 4352 (B,128,133) Fuse 3.15 A CEK1259FU 4601 (B,103,60) Fuse 5 A CEK1261FU 4602 (B,143,58) Fuse 5 A CEK1261FU 4642 (B,157,71) Fuse 2.5 A CEK1258FU 4662 (B,147,55) Fuse 2.5 A CEK1258
>>>>>>>
AVIC-F700BT/XS/UC1321 2 3 4
C
D
F
A
B
E
E
1
5
1
5
1
F
C4601
Q46014608
R629 R6
R633
R
R639 R6
C6
R642
R645
648
R649
R4601
C
C616
R652
C4251
C4253
C4261
C632
R4252
R4
R4255
R4261
98
IC607
R701
R708
R709
716
IC1021
C4703
Q43
C702
C4337
R4331
R4337
C4361
R4343
D4352
R4361
5 6 7 8
A
SIDE B
100 90 80 70 60 50 40 30 X
130
120
110
100
90
80
70
60
50
40
30
20
10
0
Y
20 10
E
E
E
E
E
E
E
E
E
E
1
5
1
5
1
1
1
5
10
15
20 25 30
35
40
45
505560
1510
15
20
25 30 35
40
45
1
1 5
1
15
15
1
5
1
5
11 1
11 1
1
10
1 5
101
1
5
10
15
20
25
R3610
R3611
R3612
R3613
R3614
R3615
R3616
R3617
R3618
R3619
U4601
R602
R3620
C4200
R609
R3621
R3622
C4202
C4203
R3623
R3624
C4204
R3625
R3626
C4206
R3627
C4207
R610
R3629
R611
R612
R618
C4211
C4215
C4216
C4217
R625
R4001
R626
R628
C4221
C4222
C4224
R63031
R632
R636
637C4231
L1401
L1402
Q4231
Q4232
C602
40
R641
06
C607
C608
C609
C4241
FU
2900
C613
614
C615
C619
L1421
L1422
C4252
L1423
C4254
R4616
C623
R4231
R4232
R4233
R4234
R4041
R4235
R4236
R4237
R4240
R4241
C635
L4701
C636
X1481
C4271
C4273 C4274C4275
C4276
C4277
C4278
C4279
R4251
253
R4254
R688
C4280
R689
C4281
IC4251
C4282
C4283C4284
C2920
C4285
C2921
C4286
C2922
C4287
C2923
C2925
L4722
C2926
C2927
L4723
C2928
L4724
R695
L4725
R696
R697
C4290
L1461
C4292
L1463
L1464
C4296
R4271
R4272
R4273
R4274
R4275 R4276
R4277
R4278
IC4271
C671
R4280
R4281
R4282
R4283
R4284
R2920
R4285
R2921
R4286
R2922
R4287
R2923
R4288
R4289
IC601
L4171
L4172
R4290
R4291
R4293
IC608
R4295
IC609
L4372
C695
C696
C697
R2940
R2943
R2944
R2945
R2946
L731
R2951
R2952
R2953
R2954
C1401C1402
C1403
C1404
R2959
C1405
Q1401
C1020
C1021
C1022
R2960
R2961
R2967
R2968
R2969
R2970
R2971
R2972
R2973
R2974
R2975
C1421
C4301
C1422
R2976
R2977
C1423
C4303
C4304
C1424
Q1421
Q4301
C1425
C1426
R1016
R715
IC1016
R1409
C4311
Q4311
Q4312Q4313
Q4314
C4701C4706
C4707
C4709
D4301
R731
C4711
R1421
R4301
R1422
R1423
R1424
R1425
R1426
C4719
C1451C1452C1453C1454
C1455
D4311
31
C1456
D4312
Q4332
C1457
Q4333
C1458
C4338
R4311
C4339
R4312
R4313
R4314
C4724
R4316 R4317
C4340
C4341
C4342
C711
C4151
C4152C
4153
C1467
C1468
C4154
C1469IC4701
C4155
C4156
IC4702
C4157 C4158
C4159
C1470
C1471
C1472
C1473
C4160
C1474
C4161
C1475
D4331
C2800
R4332
R4333 R4334
C2805
D4721
R4335
C2806
D4722
R4336
D4723
D4724
R4338
D4725
R4339
C4362
D4726
C1483
D4727
C4172
C1487
R4727
R4728
C4174
C1488
R4340
R1461
C1489
C2811
IC4721
R4341
R1462
R4342
C4177
R1463R1464
Q2810
R4344
R4151
R1465
R4345
R4152
R1466
R4346
Q4753
R4153
R1467
R4347
Q4754
R4154
R1468
R4348
R1469
C1491
R4155
C1492
R4156
C1493
R4157
R4158 R4159
C4181
L4231
C4182
C4183
C1497
C4184
R1470
R1471
C4185
C4186
R1472
R1473
C4187
R4160
C4188
R1474
R4161
C4189
R1475
R1476
R4162
R1477R1478
R1479
C4190
C4191
C4192
C4193
C4194
R4749
C4195
C2831
R4362
C2832
R4363
C4197
C2833
R4364
R4170
C4198
R4365
R4171
R1485
R4366
R1486
R1487
R4173
R4174
R4750
R1488
R4175
R1489IC1481
ZNR1401
R4176
IC4171
D4372
R1490
R1492 R1494
R1497
L602
R4187
R4188
L607
L608
L609
D2830D2831
U695
C3601
L610
C3604
R2830
R4194
R4195
R2831
Q3601
Q3602
Q3603
C3607
Q3604
R2834
R4198
C3608
R4199
Q3605
Q3606
IC2830
R4779
R4780
R4781
2874RR
3601
R3602
R3603
R3604
R3605
R3606
R3607
R3608
R3609
1
1
AVIC-F700BT/XS/UC 1335 6 7 8
C
D
F
A
B
E
1 2 3 4
11.2 KEYBOARD UNIT
B
SIDE AB KEYBOARD UNIT
1
1
1
1
1
15
1
5
10
1
R802
R807
R809
R810
CN802
C801
C803
C804
C805
C806
C807
R850
S801
S802
S803
S804
S805
D801
D802D805
D809
D810
D815
D854D855
D857
D858
D861
D862
D863D866
D867
D869
D870
D871
D872
ANT801
10 20X
90
80
70
60
50
40
30
20
10
0
Y
AV-IN
ROTARYCOMMANDER
RESET
MENU
EJECT
MAP
BT-ANTENNA
AVIC-F700BT/XS/UC1341 2 3 4
C
D
F
A
B
E
5 6 7 8
B
SIDE BB KEYBOARD UNIT
20 10X
90
80
70
60
50
40
30
20
10
0
Y
1 5 10 15 20
R801
R803
R804
R805
R806
R808
CN801
CN803
C802
C854C856
D803
D804
D806
D807
D808
D811
D812
D852D853D856
D859
D860
D864
D868
PANEL UNITOTJ2
NAVI UNITBTJ2
AVIC-F700BT/XS/UC 1355 6 7 8
C
D
F
A
B
E
1 2 3 4
11.3 CD CORE UNIT(S10.5COMP2)
C
SIDE AC CD CORE UNIT(S10.5COMP2)
PICKUP UNIT(P10.5)(SERVICE)A CN701
M2LOADING
/CARRIAGEMOTOR
M1SPINDLEMOTOR
AVIC-F700BT/XS/UC1361 2 3 4
C
D
F
A
B
E
5 6 7 8
C
SIDE BC CD CORE UNIT(S10.5COMP2)
AVIC-F700BT/XS/UC 1375 6 7 8
C
D
F
A
B
E
1 2 3 4
12. ELECTRICAL PARTS LISTNOTE: Parts whose parts numbers are omitted are subject to being not supplied. The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS..... The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Meaning of the figures and others in the parentheses in the parts list. Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board. IC 301 (A, 91, 111) IC NJM2068V The expression of the unit in this manual is shown by u instead of µ. Please do not make a mistake.
Circuit Symbol and No. Part No.
Unit Number : CWN3170(UC)
Unit Number : CWN3168(EW5)
Unit Name : AV Unit
Unit Number :
Unit Name : Keyboard Unit
Unit Number : CWX3514
Unit Name : CD Core Unit(S10.5COMP2)
AUnit Number : CWN3170(UC)Unit Number : CWN3168(EW5)Unit Name : AV Unit
MISCELLANEOUS
IC 601 (B,46,6) IC TC7SH08FUS1IC 603 (B,121,44) IC TC7SH04FUS1IC 604 (B,121,41) IC TC7S32FUIC 605 (A,42,8) IC TC74VHCT08AFTS1IC 608 (B,97,44) IC BD5335FVE
IC 609 (B,27,8) IC TC74VHC08FTS1IC 610 (A,107,34) IC(UC) PEG447A
(A,107,34) IC(EW5) PEG446AIC 1007 (A,88,128) IC PAL007CIC 1008 (A,56,38) IC NJM2125F
IC 1016 (B,69,33) IC BA4558RFVMIC 2801 (A,168,99) IC BA00CC0WCP-V5IC 2820 (A,168,88) IC BA00CC0WCP-V5IC 2830 (B,33,36) IC BA00BC0WFPIC 2890 (B,156,104) IC TPD1018F
IC 3601 (A,11,20) IC M62343FPIC 4171 (B,67,49) IC AN15887AIC 4251 (B,103,107) IC NJM2505AFIC 4271 (B,68,73) IC PML018AIC 4601 (B,118,65) IC TPS5103IDB
IC 4641 (B,150,24) IC TPS5103IDBIC 4701 (B,88,55) IC BD3931HFPIC 4702 (B,95,7) IC NJM2885DL1-33IC 4703 (A,86,45) IC S-L2980A33MC-C6SIC 4721 (B,44,129) IC(UC) HA12241FP