INSTALLATION INSTRUCTIONS TOYOTA MOTOR CORPORATION PART NUMBER Manual Ref. Nr. D3RT25/W-0-0 FOR ** T25 * R TOYOTA NAVIGATION SYSTEM Avensis (RHD) MOUNTING BRACKET KIT PZ425-T0330-60 RDS-ANTENNA KIT PZ445-T9281-00 NAVIGATION KIT 08545-20800 ADDITIONAL PARTS see page 7
28
Embed
Avensis (RHD) - Toyota Service Information77D74891-DEAF-42FB-9E2C-F09658… · installation instructions toyota motor corporation part number manual ref. nr. d3rt25/w-0-0 for **t25*r
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
INSTALLATION INSTRUCTIONS
TOYOTA MOTOR CORPORATION
PART NUMBER
Manual Ref. Nr. D3RT25/W-0-0
FOR
**T25*R
T O Y O T A N A V I G A T I O N S Y S T E M
Avensis (RHD)
MOUNTING BRACKET KIT PZ425-T0330-60RDS-ANTENNA KIT PZ445-T9281-00NAVIGATION KIT 08545-20800ADDITIONAL PARTS see page 7
06-03
Avensis (T25) TNS300ETA
Avensis (RHD) - 2
PRECAUTIONS
• Do not pinch the rear wiring or har-ness in the tightened part.
PLEASE READ THOROUGHLY THESE PRECAUTIONS BEFORE THE INSTALLATION
• Be sure to disconnect the negative(-) lead from the battery terminals.
• When passing the wires through thedashboard or other panels, use agrommet to ensure waterproofing.
• Protect the wiring with tape when it ispassed through a hole.
• When disconnecting the connectors,be sure to grip the connector body.Do not tug on the wiring.
• Do not forcibly pull any car wiring harness.Rough tugging may result in opened con-nections, or a broken wire or harness.
• Confirm that lamps, horn, wiper andother car accessories operate normally.
• Protect your car with fender covers, seatand so on.
• Use the correct tool when tighteningbolts or nuts.
• Before drilling a hole, check that the rear ofthe mounting wall is clear.
• Be sure to firmly tighten connectorsand terminals.
• Before connecting the power wiring tothe battery, check the wiring con-nections, harness, etc. to see that theyare properly secured.
• Check body and trim near area of installation to be certain nodirt or scratches resulted from the installation.
7. Required parts ....................................................................................................................................................... 6
8. Additional parts ...................................................................................................................................................... 7
12. Installation of the GPS antenna .............................................................................................................................. 16
14. Installation of the RDS antenna wire ...................................................................................................................... 19
15. Installation of the RDS antenna ............................................................................................................................ 21
16. Installation of the TNS computer + ETA ................................................................................................................. 23
17. Installation of the navigation disc .......................................................................................................................... 26
To be ordered separately. Please refer to the list of available DVD-ROM for TNS300 Navigation Systems (Access to accessories).
OWNER’S MANUAL
To be ordered separately.
REQUIRED PARTS
(1): For vehicles without pre-wired RDS-antenna.
RDS-ANTENNA KIT PZ445-T9281-00
(1)
(1)
I II
III IV
No. Part name Part No. Quantity
Antenna strip PZ445-E9281-01 1
(1) RDS antenna wire PZ445-T9281-01 1
(1) Ground bolt 1
Fakra connector PZ445-E9330-01 1IV
III
II
I
Avensis (T25) TNS300ETA
Avensis (RHD) - 7 06-03
No. Part name Part No. Quantity
Bracket cover 86804-32010 1
RDS-Tuner PZ445-E9330-02 1
Subwire harness PZ445-E9330-03 1
(3) Extension wire PZ445-T0210-60 1
(2) GPS antenna 08663-00811 1
(2) Earth plate 08674-00810 1
Wire tie 1212
11
9
8
5
4
2
2 4
5 8
12119
ADDITIONAL PARTS
(2): For vehicles without pre-wired GPS-antenna.(3): For vehicles without pre-wired connector.
(2) (2)
(3)
Avensis (T25) TNS300ETA
Avensis (RHD) - 806-03
WIRING CONNECTION
Connection Method:
Vehicle Wire harness
4
8
9
No. Part name
RDS-TUNER
SUBWIRE HARNESS
EXTENSION WIRE
GPS ANTENNA
NAVIGATION ECU
RDS ANTENNA WIREII
A
98
5
4
1P
8P
13P
A
5
GPS antenna
II
Avensis (T25) TNS300ETA
Avensis (RHD) - 9 06-03
INSTALLATION OVERVIEW
9
4
8
A
EXTENSION WIRE
GPS ANTENNA WIRE
RDS ANTENNA WIRE
RDS-TUNER
ANTENNA STRIP
NAVIGATION ECUA
I
4
II
9
8
II
I
Avensis (T25) TNS300ETA
Avensis (RHD) - 1006-03
VEHICLE DISASSEMBLY
Fig. 3
Fig. 1
Fig. 2
1
2
3
3. Remove the instrument panel clustermoulding .
: Clip (5x)3
1. Remove the shift knob .
2. Remove the shift hole cover .: Clip (4x)
2
1
4. Remove the console panel .: Clip (6x): Screw (2x)108
19
FOR M/T MODELS
FOR ALL MODELS
19
108
Avensis (T25) TNS300ETA
Avensis (RHD) - 11 06-03
Fig. 6
7. Remove the heater control assembly.
: Bolt (4x)1004
4
100
Fig. 4
5. Remove the rear console heater panelas shown using bolts (2x).: Bolt (2x)
: Clip (4x)109
10920
Fig. 5
6. Remove the cover of the midconsole.
: Bolt (2x): Screw (4x)111
11021
20
21
109
111
110
Avensis (T25) TNS300ETA
Avensis (RHD) - 1206-03
10. Remove the kick panel (L) .: Nut (1x)
: Hook (2x)102
7
Fig. 9
7
102
Fig. 7
Fig. 8
8. Remove the multi display .: Screw (2x)
: Clip (2x)101
5
5
6
101
9. Remove the front door scuff plate (L).: Hook (6x)
6
Avensis (T25) TNS300ETA
Avensis (RHD) - 13 06-03
11. Remove the glove box .: Bolt (1x)103
8
Fig. 10
Fig. 11
8103
9
104
12. a) Remove the passenger and driver side
sun visor holder by turning it 90°counterclockwise.
b) Remove the passenger side sun visor.: Clip (2x): Screw (2x)104
10
9
Fig. 12
13. Remove the rain sensor cover .22
ONLY FOR VEHICLES WITH RAIN SENSOR
10
22
16. Remove the passenger side front pillargarnish .
: Clip (2x)13
Avensis (T25) TNS300ETA
Avensis (RHD) - 1406-03
14. Remove the map lamp cover .: Clip (6x)
11
Fig. 13
11
15. Release the map lamp assembly .: Screw (2x)105
12
Fig. 14
Fig. 15
First release the clip at the innerside of the pillar.
106
CAUTION
12
105
106
13
Avensis (T25) TNS300ETA
Avensis (RHD) - 15 06-03
17. Remove the passenger seat .: Bolt (4x)107
14
Fig. 16
10714
Avensis (T25) TNS300ETA
Avensis (RHD) - 1606-03
INSTALLATION OF THE GPS ANTENNA
1. Cut the foam (d) into 8 large piecesand 2 small pieces as shown in theillustration.
(d)-a: Foam tape (8x)(d)-b: Foam tape (2x)i
i
i
Fig. 18
Fig. 19
3.a) Remove the release paper of the earth
plate and attach the butyl tape asshown.
b) Apply the tapes to the adhesive sideof the earth plate .11
C
C1111
x 2
x 8
Fig. 17
C
C
(d)
2. Cut one butyl tape into 2 equal sizedpieces.
C
i
Avensis (T25) TNS300ETA
Avensis (RHD) - 17 06-03
4.a) Attach the earth plate to the multi
display as shown and mount theGPS antenna to the earth plate .
b) Fix the antenna cord using the foamtapes (d)-a (2x).i
9
119
511
Centre
Fig. 20
Fig. 21
9
9
11
(d)-a
When affixing the earth plate makesure to carefully wipe of any dirt,moisture or oil from the surface of thelocation where it is to be affixed.
11
CAUTION
5
5. Route the antenna cord as shown.9
i
Avensis (T25) TNS300ETA
Avensis (RHD) - 1806-03
WIRE HARNESS INSTALLATION
1. Disconnect the 18P connector of thevehicle wire harness as shown.15WIRE SIDE VIEW
18P
3.a) Route and attach the extension wire
and GPS antenna cord along themidconsole area through the excistingslit using wire ties .
: Wire tie (2x).b) Bundle up and attach the excess part
of the extension wire and excessGPS antenna cord as shown usingwire ties .
: Wire tie (2x).12
12
9
8
12
12
9
8
Fig. 22
Fig. 23
Fig. 24
15
15
18P
8
9
12
12
8
9
8
9Excisting slit
Excess wire
Excess wire
2.a) Connect the 18P connector of the
extension wire to the vehicle wireharness .
b) Attach the extension wire and GPSantenna cord to the vehicle wire har-ness using a wire tie .
: Wire tie (2x).12
12159
8
158
Avensis (T25) TNS300ETA
Avensis (RHD) - 19 06-03
INSTALLATION OF THE RDS ANTENNA WIRE
Fig. 27
15
Fig. 25
ground wire
12
16
1. If not yet insulated, insulate the com-plete ground wire of the RDS antennawire by wrapping it into tape .16II
3.a) Tuck the RDS antenna wire into the
space between the roof headliner andwindshield.
b) Route and attach the RDS antennawire to the vehicle wire harness along the passenger side front pillarusing wire ties .
: Wire tie (2x)12
12
15II
II
II
II
Fig. 26
2. Cut off the indicated area of the lip ofthe RDS-antenna using scissors.II
Lip
II
06-03
Avensis (T25) TNS300ETA
Avensis (RHD) - 20
5. Route the RDS antenna wire alongthe front door scuff plate area throughthe excisting slit and attach using thevehicle clamps .
: Vehicle clamp (2x).1717
II
Fig. 29
17Excisting slit
II
4. Route and attach the RDS antennawire along the instrument panel tothe vehicle wire harness as shownusing wire ties .
: Wire tie (2x)12
12
15II
Fig. 28
15
12
II
Avensis (RHD) - 21 06-03
Avensis (T25) TNS300ETA
INSTALLATION OF THE RDS ANTENNA
centre
70 mm 20 mm
Coated area
Fig. 30
2.a) Thoroughly clean the mounting sur-
face of the front window to which theantenna strip is to affixed.
b) Remove the release paper of theantenna strip .
c) Attach the antenna strip to the frontwindow as shown. Ensure that theantenna strip is attached horizontal-ly.
I
I
I
I
Fig. 31
Be sure the top side of the joggle ispushed against the body of the roof.
CAUTION
centre
ONLY FOR VEHICLES WITH RAIN SENSOR
I
I
II
Antenna joggle
Avensis (T25) TNS300ETA
Avensis (RHD) - 2206-03
Fig. 32
Antenna joggle
centre
Be sure the top side of the joggle ispushed against the body of the roof.
CAUTION
ONLY FOR VEHICLES WITHOUT RAIN SENSOR
3.a) Route the ground wire of the RDS
antenna as shown.b) Attach the ground wire using screws
when reassembling the map lampassembly .
: Screw (2x)10512
105
II
Ground wire
Fig. 33
10512
Make sure to route the ground wire insuch a way that it will not cause shortcircuit.
CAUTION
I
I
II
Avensis (T25) TNS300ETA
Avensis (RHD) - 23 06-03
INSTALLATION OF THE TNS COMPUTER + ETA
Fig. 34
30 mm
20 mm
30 mm
1.a) Slit the floor carpet according to the
measurements as shown.b) Remove the button by turning it
counterclockwise.18
18
Fig. 35
(a)
B
(b)
Fig. 36
3.a) Attach the RDS-tuner to the naviga-
tion ECU bracket (b) using bolts (c).(c): Bolt (M5x8) (2x)
b) Fit the TNS-cover to the side brackets (a) and (b) using theexisting clips.
ii
2i
i
i
4
(b)
(a)
(c)
Ai
i
i
i
i
2. Attach the navigation ECU-brackets(a) and (b) to the navigation ECUusing bolts .
: Bolt (M5x8) (4x)B
BA
ii
2
4
Avensis (T25) TNS300ETA
Avensis (RHD) - 2406-03
Black wired Pin
antenna connector
6.
a) Connect the RDS-antenna connec-tor to the fakra connector as shown.
b) Insert the fakra connector with theantenna connector to the RDS-tuner
.4
IV
IV
II
Be careful not to close the fakra con-nector before the RDS antennaconnector is inserted till it clicks.II
IV
ATTENTION
Fig. 39
4
AII
II
IV
IV
Fig. 37
Navigationharness
4
Navigation harness
13P
13P
13P
8P1P8P 5
5
WIRE SIDE VIEW
Black wired Pin
12P
Fig. 38
A
A
4
4.a) Connect the 1P and 8P connector of
the navigation harness to the naviga-tion ECU .
b) Connect the navigation harness 13Pfemale connector to the subwire har-ness 13P male connector.
c) Connect the 13P subwire harness connector to the navigation ECU .
d) Connect the 12P subwire harness connector to the RDS-tuner .4
5
A
5
5
A
II
5.a) Locate the RDS antenna black
wired pin.b) Connect the RDS antenna black
wired pin to the subwire harness 12P connector to the second positionfrom the left on the top row (wires faceyou and tab is on top).
5
II
II
Avensis (T25) TNS300ETA
Avensis (RHD) - 25 06-03
9. Bundle up and attach the excess wireharness using wire ties asshown.
: Wire tie (2x).12
128
Fig. 42
8
12
Fig. 41
4
A
B
(a)
(b)
18
i
i
Fig. 40
4
A
(a)i
7. Push the bracket (a) of the naviga-tion ECU with RDS-Tuner intothe slit on the floor under the passen-ger seat as shown.
4A
i
When affixing the navigation ECU ,make sure to carefully wipe off anydirt, moisture or oil from the surfaceof the location where it is to be affixed.
A
CAUTION
8.a) Attach the bracket (a) of the naviga-
tion ECU with RDS-Tuner usinga button as shown.
b) Attach the bracket (b) of the naviga-tion ECU with RDS-Tuner usinga bolt as shown.B
4A
i
184A
i
06-03
Avensis (T25) TNS300ETA
Avensis (RHD) - 26
INSTALLATION OF NAVIGATION DISC
Fig. 43
1. Connect the battery and turn the igni-tion switch to the ACC position.
2. Slide the eject switch on the computerto the left to open the disc insertionslot.
3. With the label side of the disc facingup, insert the Navigation Disc into thedisc insertion slot.
* The disc will be pulled into thecomputer automatically.
4. Slide the eject switch on the computerto the right to close the disc inser-
tion slot.1
06-03
Avensis (T25) TNS300ETA
Avensis (RHD) - 27
Return all vehicle parts that have been removed to their original locations. Especially make sure to attach trim and other inte-rior materials properly so that they do not have a detrimental effect on the function of the vehicle. During reassembling, makesure that wires are not pinched and all bolts and screws are tightened.
REASSEMBLING
POST-INSTALLATION INSPECTION
ENSURE THAT ALL REMOVED CONNECTORSARE PUT BACK CORRECTLY.
REFIT THE TRIM AND REMOVED PARTS.
Installation Check
1. Inspect the wiring and installation for abnormalities.2. Check particularly closely for any locations where the vehicle harness, wire harness or divergency harness is being pushed, pulled
or pinched with excessive force. Also check again that clamps and bands have not shifted out of position and that all parts havebeen tightened.
Operation Check
1. Attach the (-) terminal of the battery and turn the key to the ACC or ON position or start the engine.2. Press the NAVI switch and confirm that the navigation screen is displayed.3. Adjust the volume by following the section on ”Adjusting the Volume of the Guide Voice” in the TNS300 Owner’s Manual, and
confirm that the sound from the speakers changes.4. Perform the “auto-compensation” procedure by following the section on “When Tires are Replaced” in the TNS300 Owner’s
Manual.
When an abnormality is suspected, perform troubleshooting based on the “Toyota Genuine Navigation System Service Manual”.