Top Banner
Underground drilling specialists Phone: (08) 9093 7600 Fax: (08) 9093 0388 Email: [email protected] Features Specifications ATLAS COPCO SIMBA H1257 Weight 11,800kg Width 2000mm Height Roof up 2800mm Roof down 2100mm Length for transport 8800 Diesel hydraulic tramming 5 cylinder deutz motor Max tramming speed flat ground 10km /h 1:8 decline 4km/h Carrier; 4 wheel drive, articulated steering, hydrodynamic transmission, service brakes, 2 separate circuits (hydraulically applied, fully enclosed wet disc brakes) Certified F.O.P.S canopy 1000 Volt electric hydraulic operation total installed power 65kw Low voltage system 24v Angle reading instrument ARI 1257 1838 drifter & 1238 drifters using R32, T38 & T45 running gear 10 rod handler capable of mechanized drilling to 20m 4 extendable outrigger jacks Front & rear hydraulic stingers to ensure stable set up for feed rail 45L fire suppression system 4.5kg dry chemical powder fire extingisher Hydraulic driven water booster pump – capacity @ 7 bar boost max 80l/min minimum inlet pressure 2 bar Laser offsets 3.9m @ 0º Dump 4.6m @ 10º Dump for 5m backs 5.3m @ 20º Dump for 10m backs The Simba H1257 is a compact, electric hydraulic, rig boom – mounted drill rig with 10 rod carousel. This top hammer rig is designed for small to medium sized drives and is capable of drilling 51mm to 89mm diameter holes and reaming to 127mm. It’s boom mounted rail makes it capable of performing 360 degree ring drilling. It is also capable of drilling parallel holes up to 5.7m apart from one set up.
2
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: Atlas Copco Simba h1257

Underground drilling specialistsPhone: (08) 9093 7600Fax: (08) 9093 0388

Email: [email protected]

Features

Specifications

ATLAS COPCO SIMBA H1257

• Weight 11,800kg• Width 2000mm• Height Roof up 2800mm Roof down 2100mm• Length for transport 8800• Diesel hydraulic tramming 5 cylinder deutz motor• Max tramming speed flat ground 10km /h 1:8 decline 4km/h• Carrier; 4 wheel drive, articulated steering, hydrodynamic transmission, service brakes, 2 separate circuits (hydraulically applied, fully enclosed wet disc brakes)• Certified F.O.P.S canopy• 1000 Volt electric hydraulic operation total installed power 65kw

• Low voltage system 24v• Angle reading instrument ARI 1257• 1838 drifter & 1238 drifters using R32, T38 & T45 running gear• 10 rod handler capable of mechanized drilling to 20m• 4 extendable outrigger jacks • Front & rear hydraulic stingers to ensure stable set up for feed rail• 45L fire suppression system• 4.5kg dry chemical powder fire extingisher• Hydraulic driven water booster pump – capacity @ 7 bar boost max 80l/min minimum inlet pressure 2 bar• Laser offsets 3.9m @ 0º Dump 4.6m @ 10º Dump for 5m backs 5.3m @ 20º Dump for 10m backs

The Simba H1257 is a compact, electric hydraulic, rig boom – mounted drill rig with 10 rod carousel. This top hammer rig is designed for small to medium sized drives and is capable of drilling 51mm to 89mm diameter holes and reaming to 127mm. It’s boom mounted rail makes it capable of performing 360 degree ring drilling. It is also capable of drilling parallel holes up to 5.7m apart from one set up.

Page 2: Atlas Copco Simba h1257

ATLAS COPCO SIMBA H1257

The technical information and photographs contained in this document are reproduced courtesy of Atlas Australia Pty. Limited.

2060

1350

1350

2100

2800

7450

3900

RA

L 65

0

900

Feed

ext

ensi

on

Dim

ensi

on

s in

mm

6150

175

2605

1250

1250

1380

Stin

ger

ext

ensi

on

55˚

35o

35

5757

*

* p

aral

lel c

over

age

R2

84

0

± 11

360

˚

(24

˚)

6014

8750

Rig

alig

nm

ent

lase

r po

siti

on

4100

300

500

500