athena A2 Kit User Manual Version 1.0 Published August 2020 Copyright©2020 ASRock INC. All rights reserved.
athena A2 Kit
User Manual
Version 1.0Published August 2020
Copyright©2020 ASRock INC. All rights reserved.
Version 1.0 Published September 2020 Copyright©2020 ASRock INC. Inc. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock.
Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock. assumes no responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance.“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock INC.’s Website: www.asrockind.com
The terms HDMI® and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
CAUTION:
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Specifications 2
1.3 Motherboard Layout 4
1.4 I/O Panel 7
1.5 Expansion Slots (M.2 Slots) 8
1.6 Jumper Setup 9
1.7 Onboard Headers and Connectors 10
1.8 Power and Reset Switch 13
Chapter 2 Installation 14
2.1 Hardware Setup 14
2.2 Installing the Heatsink FAN 17
2.3 Connecting with the SATA Power and SATA Data Cables 18
Chapter 3 Software Settings 19
3.1 Settings for the Ubuntu operating system 19
3.2 IP Camera Settings 22
3.3 OpenVINO™ Toolkit 24
3.4 AWS Greengrass 26
athena A2 Kit
PB 1
Engl
ish
Chapter 1 IntroductionThank you for purchasing ASRock Industrial athena A2 Kit, a reliable motherboard produced under ASRock INC.’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock INC.’s commitment to quality and endurance.
1.1 Package Contents• 1 x athena A2 Motherboard • 1 x Heatsink FAN • 1 x IP Camera • 1 x IP Camera Signal Cable • 1 x IP Camera Power Cable• 1 x SATA Data Cable• 1 x SATA Power Cable • 1 x M.2 (Key M, 2280) Myriad X/Keem Bay (Optional) • 8 x Standoffs • 1 x AC-in 100-240V, DC-out 12V Power Adapter
If any items are missing or appear damaged, contact your authorized dealer.
If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. https://event.asrockind.com/tsd.asp
2 3
English
1.2 Specifications
athena A2Form FactorDimensions 6.5-in x 3.8-inProcessor SystemCPU Intel® Atom Apollo Lake J3455 processor Chipset SoCBIOS AMI SPI 128 MbitMemoryTechnology Onboard LPDDR4 2400 MHzCapacity 4 GB, up to 8GBGraphicsController SoC integrated graphicsHDMI HDMI 1.4b
Max resolution up to 3840x2160@30HzExpansion SlotM.2 1 x M.2 (Key E, 2230) with PCIe x1 and USB 2.0 for WirelessSIM Socket 1 x micro SIM Socket connected to M.2 Key B 3042/3052EthernetController/ Speed
LAN: 1 x Realtek RTL8111G with 10/100/1000 Mbps (PoE (PD) with 25.5W)LAN: 2 x Realtek RTL8111G with 10/100/1000 Mbps (IP Camera Header)
Connector 1 x RJ-45Rear I/OHDMI 1 x HDMI 1.4bEthernet 1 x 1 Gigabit LAN, Optional PoE (PD) with 25.5WUSB 2 x USB 3.2 (Gen1)others 1 x Micro SD connectorInternal ConnectorUSB 2 x USB 2.0 headerTPM TPM 2.0 onboard ICSATA PWR Output
1 x 4-pin SATA Power
IPCAM interfaceLAN signal 1x6 headerPower 1x2 header
40-pin GP-bus 40 pin General Purpose busStorage
M.21 x M.2 (Key B, 3042/3052) with PCIe x1 and USB 3.2 Gen1, USB 2.01 x M.2 (Key M, 2280) with PCIe x2
SATA 1 x SATA3 (6Gb/s)
athena A2 Kit
2 3
Engl
ish
* For detailed product information, please visit our website: http://www.asrockind.com
eMMC Onboard eMMC 32GBWatchdog TimerOutput From Super I/O to drag RESETCON#Interval 256 Segments, 0, 1, 2, ...255secPower RequirementsInput PWR 12V DC-In (DC Jack)
PoE (PD) with 25.5W (LAN Port) (Optional)Power On AT/ATX Supported
- AT : Directly PWR on as power input ready - ATX : Press button to PWR on after power input ready
EnvironmentOperating Temp 0ºC ~ 50ºCStorage Temp -40° C – 85° COperating Humidity
10% ~ 90%
Storage Humidity
10% ~ 90%
OthersIP camera 2MP, 1080P@30fps, H.264Movidius 1 x M.2 (Key M, 2280) Myriad X/Keem Bay (Optional)Adapter 1 x AC-in 100~240V, DC-out 12VOS Support Linux Ubuntu 16.04
Accessories
1 x IP Camera Signal Cable1 X IP Camera Power Cable1 x SATA Data Cable1 x SATA Power Cable1 x Heatsink Fan8 x Standoffs
4 5
English
1.3 Motherboard Layout
BIOSROM
Ind
us
tria
l
R
CAM
CAM_PWR1
RESET1
1 2 3
SATA3_1
SATA_PWR1
USB2_4_5
USB2_2_3
PANEL1 LPC1
FAN1
BAT1
CLRMOS1 PWR_JP1
4
5
6
7
8
9
10
11
12
13
14
15
PWR_BTN1
HDMI1
S 1D
USB 3.2 Gen1T: USB3_1B: USB3_0
ETH_PWR1
DC_JACK1
athena A2 Kit
4 5
Engl
ish
No. Description
1 USB2.0 Connector (USB2_2_3)
2 40-pin General Purpose Bus Connector (PI1)
3 FAN Connector (FAN1)
4 Battery Connector (BAT1)
5 LPC Debug Header (LPC1)
6 System Panel Header (PANEL1)
7 Power Button (PWR_BTN1)
8 Reset Button (RESET1)
9 IP Camera Power Connector (CAM_PWR1)
10 ATX/AT Mode Jumper (PWR_JP1)
11 IP Camera Signal Connector (CAM1)
12 Clear CMOS Headers (CLRMOS1)
13 SATA3 Connector (SATA3_1)
14 USB2.0 Connector (USB2_4_5)
15 SATA Power Output Connector (SATA_PWR1)
6 7
English
Back Side
M2_M1
M2_E1
16
17
18
SIM1 M2_B1
NUT_B2 NUT_B1
NUT6
NUT1
19
No. Description
16 M.2 Socket (Key E, Type 2230)
17 M.2 Socket (Key M, Type 2280)
18 M.2 Socket (Key B, Type 3042 / 3052)
19 micro SIM Socket (SIM1)
athena A2 Kit
6 7
Engl
ish
1.4 I/O Panel
No. Description No. Description
1 Micro SD Card Slot (SD1) 4RJ-45 LAN (PoE, PD 25.5W, Optional) (ETH_PWR1)
2 HDMI 1.4b (HDMI1) 5 12V DC-in (DC_JACK1)
3USB 3.2 Gen1 Connector (USB3_0_1)
1 32 4 5
8 9
English
1.5 Expansion Slots (M.2 Slots)There are 2 M.2 slots on this motherboard.
M.2 for SSD: Key B (M2_B1) (3042 / 3052) PCIe x1 and USB 3.2 Gen1 and USB 2.0. M.2 for SSD: Key M (M2_M1) (2280) PCIe x2. M.2 for Wi-Fi: Key E (M2_E1) (2230) supports with PCIe x1 and USB 2.0 for Wireless.
Pin Signal Signal Pin
1 NA +3.3V 2 3 GND +3.3V 4 5 GND FuLL_Card_Power_off 6
7 USB_D+ W_DISABLE 8 9 USB_D- WWAN_LED# 10
11 GND
21 NA NA 20 23 NA NA 22
25 NA NA 24 27 GND NA 26 29 USB3_RX- NA 28
31 USB3_RX+ UIM_RESET 30 33 GND UIM_CLK 32 35 USB3_TX- UIM_DATA 34
37 USB3_TX+ UIM_PWR 36 39 GND NA 38 41 PERn0/ SATA-B+ SMB_CLK 40
43 PERp0/ SATA-B- SMB_DATA 42 45 GND NA 44 47 PETn0/ SATA-A- NA 46
49 PETP0/ SATA-A+ NA 48 51 GND PERST# 50 53 PEFCLKn CLKREQ# 52
55 PEFCLKp WAKE# 54 57 GND NA 56 59 NA NA 58
61 NA NA 60 63 NA NA 62 65 NA NA 64
67 NA SIM Detect 66 69 PEDET NA 68 71 GND +3.3V 70 73 GND +3.3V 72
75 NA +3.3V 74
Pin Signal Signal Pin
1 GND +3.3V 2
3 USB_D+ +3.3V 4
5 USB_D- NA 6
7 GND NA 8
9 NA NA 10
11 NA NA 12
13 GND MODEM_CLKREQ 14
15 NA NA 16
17 NA GND 18
19 GND NA 20
21 NA CNV_BRI_RSP 22
23 NA
33 GND NA 32
35 PETp NA 34
37 PETn NA 36
39 GND NA 38
41 PERp NA 40
43 PERn NA 42
45 GND NA 44
47 PEFCLKp NA 46
49 PEFCLKn NA 48
51 GND SUSCLK 50
53 CLKREQ# PERST0# 52
55 WAKE# W_DISABLE1# 54
57 GND W_DISABLE2# 56
59 NA SMB_DATA 58
61 NA SMB_CLK 60
63 GND NA 62
65 NA NA 64
67 NA NA 66
69 GND NA 68
71 NA NA 70
73 NA +3.3V 72
75 GND +3.3V 74
M.2 Key-B Socket (M2_B1) M.2 Key-E Socket (M2_E1) M.2 Key-M Socket (M2_M1)
Pin Signal Signal Pin
1 GND +3.3V 2
3 GND +3.3V 4
5 NA NA 6
7 NA NA 8
9 GND SATA_LED 10
11 NA +3.3V 12
13 NA +3.3V 14
15 GND +3.3V 16
17 NA +3.3V 18
19 NA NA 20
21 GND NA 22
23 NA NA 24
25 NA NA 26
27 GND NA 28
29 PERn1 NA 30
31 PERn1 NA 32
33 GND NA 34
35 PETn1 NA 36
37 PETn1 DEVSLP 38
39 GND SMB_CLK 40
41 PERn0 SMB_DATA 42
43 PERn0 NA 44
45 GND NA 46
47 PETn0 NA 48
49 PETn0 PERST# 50
51 GND CLKREQ# 52
53 PEFCLKn WAKE# 54
55 PEFCLKp NA 56
57 GND NA 58
67 NA NA 68
69 PEDET +3.3V 70
71 GND +3.3V 72
73 GND +3.3V 74
75 GND
athena A2 Kit
8 9
Engl
ish
1.6 Jumper Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when a jumper cap is placed on these 2 pins.
Clear CMOS Jumper(CLRMOS1)(see p.4, No. 12)
CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, and user default profile will be cleared only if the CMOS battery is removed.
ATX/AT Mode Jumper(3-pin PWR_JP1)(see p.4, No. 10)
AT Mode
ATX Mode
Clear CMOSDefault
10 11
English
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.
1.7 Onboard Headers and Connectors
System Panel Header(9-pin PANEL1)(see p.4, No. 6)
Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
GND
RESET#
PWRBTN#
PLED-
PLED+
GND
HDLED-
HDLED+
1
GND
PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch.
RESET (Reset Switch): Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the system is in S1/S3 sleep state. The LED is off when the system is in S4 sleep state or powered off (S5).
HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connect-ing your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.
athena A2 Kit
10 11
Engl
ish
LPC Debug Header(19-pin LPC1)(see p.4, No. 5)
1
GN
D
GN
D
S_
PW
RD
WN
#
LA
D2
SM
B_
CLK
_M
AIN
PC
ICLK
PC
IRST#
LA
D3
+3
.3V
LA
D0
GN
D
FR
AM
E
SM
B_
DA
TA
_M
AIN
LA
D1
SE
RIR
Q#
GN
D
+3
.3V
STA
ND
BY
48
MH
z+
5V
This connector supports a Trusted Platform Module system, which can securely store keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity.
FAN Connector(4-pin FAN1)(see p.4, No. 3) 1
FAN_SPEED_CONTROL
FAN_SPEED
+12VGND Please connect the CPU FAN
cable to the connector.
USB 2.0 Headers (9-pin USB2_2_3)(see p 4, No. 1)(9-pin USB2_4_5)(see p 4, No. 14)
DUMMYGND
GND
P+P-
USB_PWR
P+P-
USB_PWR
1
There are two USB 2.0 headers on this motherboard. Each USB 2.0 header can support two USB 2.0 ports.
IP Camera Signal Connector(6-pin CAM)(see p 4, No. 11)
MDI0P
MDI1P
MDI0N
MDI1N
1
MDI2P
MDI3N Please connect the IP Camera Signal cable to the connector.
IP Camera Power Connector(2-pin CAM_PWR1)(see p 4, No. 9)
GND
+12V
1
Please connect the IP Camera Power cable to the connector.
Serial ATA3 Connectors(SATA3_1: see p.4, No. 13)
This SATA3 connector supports SATA data cables for internal storage devices with up to 6.0 Gb/s data transfer rate.
SATA
3_1
12 13
English
SATA Power Output Connector (4-pin SATA_PWR1) (see p.4, No. 15)
+5V
+12V
1
GND
GND
Please connect a SATA (SATA_PWR1) power cable to this connector.
USB 2.0 Headers(9-pin USB3_4)(see p.4, No. 21)(9-pin USB5_6)(see p.4, No. 20)
DUMMYGND
GND
P+P-
USB_PWR
P+P-
USB_PWR
1
There are two USB 2.0 headers on this motherboard.Each USB 2.0 header can support two ports.
Battery Connector(2-pin BAT1: see p.4, No. 4)
Connect battery to this connector.
40-pin General Purpose Bus Connector(40-pin PI1)(see p 4, No. 6)
athena A2 Kit
12 13
Engl
ish
1.8 Power and Reset Switch
Power Button (PWR_BTN1)(see p.4, No. 7)
Press the Power button to turn on the deivce. Press it again to turn if off.
Reset Button (RESET1)(see p.4, No. 8)
Press the Reset button to repower on the device.
14 15
English
Chapter 2 Installation
2.1 Hardware Setup1. Take the athena A2 Kit out of the box.
2. Flip the athena A2 motherboard and IP camera over.
180o
180o
athena A2 Kit
14 15
Engl
ish
3. Install four standoffs.
4. Plug the power cord into the athena A2 motherboard and into the electrical outlet. Connect the cables to the IP Camera. IP Camera address:192.168.1.200
Black
Red
Black
Red
16 17
English
5. Carefully place the athena A2 Kit into the box.
6. Press the power button.
athena A2 Kit
16 17
Engl
ish
2.2 Installing the Heatsink FAN1. Locate the FAN on the heatsink and use screws to secure the FAN to the heatsink.2. Connect the FAN cable to the FAN connector (FAN1) on the athena A2 motherboard.
18 19
English
2.3 Connecting with the SATA Power and SATA Data Cables1. Insert the one ends of the provided SATA power and SATA Data cables into the
connectors on the athena A2 motherboard.2. Connect the other ends to a hard disk drive.
athena A2 Kit
18 19
Engl
ish
Chapter 3 Software Settings
3.1 Settings for the Ubuntu operating systemWhen your athena A2 Kit is ready and turned on for the first time, you need to set up the system configuration.
1. Select your language and click "Continue".
2. Select your time zone and click "Continue".
20 21
English
3. Select your keyboard layout and click "Continue".
4. Create your account. Enter all required information and click "Continue".
athena A2 Kit
20 21
Engl
ish
5. System will be ready for a few minutes.
6. Log in the system with the password you've set in Step 4.
22 23
English
3.2 IP Camera SettingsYou can go to the IP Camera setting page for more configurations on the system, network, A/V setting, event and others.
1. Open your web browser, such as Firefox, type web browser 192.168.1.200 in the address bar, and then press "Enter".
2. Then enter the user name and password, and click "OK" to log in. Default username: admin Default passoword: admin
3. Click on the Tool icon on the upper-right corner to enter the IP Camera setting page.
athena A2 Kit
22 23
Engl
ish
4. For example, if you want to adjust the video quality, select the "Video Setting" tab on the left panel, and then you can configure the Resolution, Video Frame Rate or other options. Click "Apply" to save the settings.
24 25
English
3.3 OpenVINO™ Toolkit Before you use the athena A2 Kit with the Intel® OpenVINO Toolkit, make usre you have properly installed the Intel® Movidius Myriad X.
1. Go to search bar and search for "Terminal".
2. Double-click on the Terminal icon.
athena A2 Kit
24 25
Engl
ish
3. Enter the OpenVINO sample code command.
Scan the QR Code below to go to the OpenVINO™ Toolkit official website to download the configuration guide for the Intel Distribution of Open-VINO™ Toolkit for Linux.
Website: https://docs.openvinotoolkit.org/latest/_docs_install_guides_installing_openvino_linux.html
26 27
English
3.4 AWS Greengrass 1. Go to "Terminal".
2. Enter the command for the AWS Greengrass.
athena A2 Kit
26 27
Engl
ish
Scan the QR Code below to view the AWS Greengrass referenced document.
Website: https://docs.aws.amazon.com/greengrass/latest/developerguide/what-is-gg.html