-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 1 v./of 38
Weitergabe sowie Vervielfltigung dieses Dokuments, Verwertung
und Mitteilung seines
Inhalts sind verboten, soweit nicht ausdrcklich gestattet.
Zuwiderhandlungen verpflichten zu
Schadenersatz. Alle Rechte fr den Fall der Patent-,
Gebrauchsmuster- oder
Geschmacksmustereintragung vorbehalten.
The reproduction, distribution and utilization of this document
as well as the communication
of ist contents to others without express authorization is
prohibited. Offenders will be held
liable for the payment of damages. All rights reserved in the
event of the grant of a patent,
utility model or design.
No guarantee can be given in respect of the translation.In all
cases the latest German-Language version of this
standard shall be taken as authoritative.
MITTEILUNG NR.
NOTE NO.
DATUM
DATE
NORMUNG
STANDARDS DEPT.
FACHABTEILUNG
OPERATING DEPT.
GESEHEN
SEEN
Continental AG. 2009 FRA-09111495 06.04.09 Kranlich Kranlich
Schemainda82.9201-0000.4 / 807 / 0182.9201-0000.4 / 807 / 01
CONTENTS
Changes[03] . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . 5
Previous editions[03] . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . 5
1 SCOPE AND PURPOSE[03] . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 5
2 REFERENCES[03] . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . 6
3 FORMAT OF THE PRODUCT DOCUMENTATION . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . 8
3.1 Master data sheet[03] . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 8
3.2 Drawing . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 8
3.3 3D model . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 8
3.4 Parts list . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 8
3.5 References . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. 8
4 DRAWING SHEET SIZES AND DRAWING FRAMES[03] . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . 9
5 PREPARATION OF DRAWINGS . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . 9
5.1 Representations . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
5.2 Scales[03] . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 9
5.3 Line widths . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 9
5.4 Line spacing for microfilming . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
5.5 Administration, Procedures and Long-Term Archiving[03] . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.6 Lettering . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 10
5.6.1 Letter sizes [03] . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . 10
5.6.2 Orthography in German-language drawings and parts lists .
. . . . . . . . . . . . . . . . . . . . . . 11
6 INFORMATION IN, OR RELATING TO, DRAWINGS . . . . . . . . . . .
. . . . . . . . . . . . . . . . 12
6.1 General[03] . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 12
6.2 Tolerance studies / calculations . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.3 Workpiece edges . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 2 v./of 38
82.9201-0000.4 / 807 / 01
6.4 Units . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 13
6.5 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
6.5.1 Dimensions not drawn to scale[03] . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . 13
6.5.2 Dimensions for parts with surface protection . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.5.3 Double dimensions (multiple dimensions) . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.5.4 Identification of characteristics with D and W . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . 14
6.6 Dimensional tolerances / tolerances of form and position . .
. . . . . . . . . . . . . . . . . . . . . . 14
6.6.1 Tolerancing principle[03] . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 14
6.6.2 General tolerances . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
6.6.3 Tolerances of form and position . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.7 Projection methods . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
6.8 References[03] . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . 15
6.9 Abbreviations identifying products . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.9.1 Units operating on mineral oil . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
6.10 Project name . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. 16
6.11 Assembly drawings[03] . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 16
6.12 Material and semi-finished product specifications in
drawings . . . . . . . . . . . . . . . . . . . . . 16
6.12.1 Entry for semi-finished products and materials . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.12.2 Entry of the material without semi-finished product
specification . . . . . . . . . . . . . . . . . . . 17
6.12.3 Optional materials . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. 17
6.12.4 Material specifications for rubber or plastic parts[03] .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.12.5 Material specifications for composite parts . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.12.6 Material specifications for purchased parts[03] . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.12.7 Material specifications for electronic parts[03] . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.13 Specification of a surface protection treatment[03] . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.13.1 Material surface area for the surface protection
treatment . . . . . . . . . . . . . . . . . . . . . . . 19
6.14 Released suppliers[03] . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 19
6.15 Specification of weight . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
6.16 Other fields on the drawing . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 3 v./of 38
82.9201-0000.4 / 807 / 01
6.17 Drawings of unmachined parts . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.17.1 Identification of unmachined parts . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
6.17.2 Mounting points . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. 20
6.18 Several item codes (part numbers) on one drawing . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . 21
6.18.1 Drawings with two numbers . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
6.18.2 Collective drawings[03] . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 21
6.19 Referencing of drawings which must be changed together[03]
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
6.20 Drawing and parts list combined on one form (PLC) . . . . .
. . . . . . . . . . . . . . . . . . . . . . . 22
6.21 Supersedes entry[03] . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 23
6.22 Photo releases . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
6.23 Y-parts . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 23
7 DATA EXCHANGE . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.1 Data exchange with suppliers . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.2 Data exchange with customers[03] . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 24
8 DESIGN PARTS LISTS . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8.1 General[03] . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 24
8.1.1 Musts in all parts lists . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
8.1.2 Entries in the notes column[03] . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . 25
8.1.3 Parts lists without related drawings . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
8.1.4 Parts lists with two numbers . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
8.1.5 Field for remarks applying to the complete parts list . .
. . . . . . . . . . . . . . . . . . . . . . . . . . 26
8.1.6 Entries in parts lists of collective drawings - chart
drawings - (Catia V4 only) [03] . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 26
8.2 Parts list entries for unmachined parts . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8.3 Parts list entries for composite parts . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8.4 Parts list entries for optional parts (alternative parts
list items)[03] . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . 27
8.5 Parts list entries for standard parts and catalog parts[03]
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
8.6 Parts list entries for development parts[03] . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . 28
8.7 Units of quantity . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. 29
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 4 v./of 38
82.9201-0000.4 / 807 / 01
9 CUSTOMER DRAWINGS . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . 30
9.1 Preparation of customer drawings . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
9.2 Special customer requirements[03] . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . 30
10 FORMS . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
10.1 Drawing frames[03] . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . 30
10.1.1 Drawing frame - layout[03] . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . 31
10.2 Master data sheet - layout[03] . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 35
10.3 Parts list - layout[03] . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 36
11 ENVIRONMENTALLY COMPATIBLE PRODUCT DEVELOPMENT[03] . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . 38
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 5 v./of 38
82.9201-0000.4 / 807 / 01
Changes[03]
Standard fully revised
Previous editions[03]
[01] F22 FRA-00125318 07.12.00[02] F21 FRA-03110905 11.03.03
1 SCOPE AND PURPOSE[03]
This standard is valid for all companies, plants and operational
divisions within theContinental Automotive Divisions (CAS) and for
their suppliers.
The companies which were subsidiaries of Siemens VDO Automotive
AG on 03.12.2007are not currently covered by this standard, nor is
Continental Automotive GmbH. Theirinclusion in this standard will
be decided upon at a later stage of the integration process.
The purpose of this standard is to apply existing drafting
experience in such a manner thatproduction documents which can be
used internationally can be prepared with the digitalsystems
available today.
In view of changing social values, special attention shall be
paid to the environmentalcompatibility of product and production in
accordance with DIN EN ISO 14001.Today, the factors characterizing
a quality product include saving of resources, a recycling-oriented
production and the preparation of energy balances. Furthermore, all
drawings are expected to meet the following requirements:The
information provided by a drawing must be complete, unambiguous and
consistent interms of function, producibility and testability.
The original drawing on paper will be replaced by the digital
document. To permit this, theworkflow of all releases and changes
must be exclusively controlled by the PLM system
(Product Lifecycle Management system).The existing drafting
guidelines remain in force, especially for 2D representations and,
asfar as applicable, also for 3D representations.
Long-term filing and the problems related to the representation
of 3D files outside CADsystems are not covered by this
standard.
Changes and additions to this standard will be advised by
Standard DepartmentInformation Bulletin (Information der
Normenabteilung). They supplement / replace theaffected items of
this standard. The part not affected remains in force.
As used in this standard, the term systems refers to EDP
management systems, such asthe PLM system or/and a CAD system with
its utility programs. Details of the use of thesesystems are not
covered by this standard.
The term drawing is retained in this standard in order to
distinguish drawings from othertechnical documents.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 6 v./of 38
82.9201-0000.4 / 807 / 01
2 REFERENCES[03]
ATE N 101 00.02 Identification of technical documents with "D"
und "W"characteristics
ATE N 101 01.04 CATIA guidelines implementation proceduresATE N
101 01.06 Sizes and Layout of drawing sheetsATE N 101 01.07
Technical drawings - ScaleATE N 101 01.20 Lettering RequirementsATE
N 101 01.21 Lettering Greek AlphabetATE N 101 01.25 Basic
Conventions for LinesATE N 101 01.28 Basic Conventions for
TolerancingATE N 101 01.33 Item ReferencesATE N 101 01.38
Tolerancing Principle, Envelope PrincipleATE N 101 02.02 Change
Directive for Master Data Lists, Drawings, 3D
models and Part ListsATE N 101 02.03 Change Directive for Usage
Types and Exchangeability
for Product Parts / Device PartsATE N 101 02.04 Change Directive
for Release / Change Entries in Master
Data Lists, Drawings and Part ListsATE N 101 06.XX
Identification of ComponentsATE N 101 13.01 Release of Polymer
MaterialsATE N 101 24.01 Units; Names, SymbolsATE N 101 75.01
CAD/CAM Data Exchange, Guideline for Data Exchange
with Suppliers and Development PartnersATE N 101 78.XX Directive
on Data Exchange with CustomersATE N 111 02.01 Workpiece Edges of
Indeterminate ShapeATE N 113 01.01 General Tolerances, Linear and
Angular DimensionsATE N 113 01.02 General Tolerances, Form and
PositionATE N 113 01.03 General Tolerances, Linear and Angular
Dimensions,
Form and Position (Basic Conventions for TolerancingEnvelope
Principle)
ATE N 105 38.04 Indication of Surface TextureATE N 550 00.01
Environmentally Compatible Product DevelopmentATE N 550 00.02
Environmentally Compatible Product Development -
SuppliersDIN EN ISO 14001 Environmental Management SystemsDIN EN
ISO 3098-0 Alphabets - Basic RulesDIN EN ISO 3098-2 Alphabets -
Latin Alphabet, Numbers and CharactersDIN EN ISO 3098-3 Alphabets -
Greek AlphabetDIN EN ISO 3098-4 Alphabets - Diacritic and Special
Characters in the Latin
AlphabetDIN ISO 5456-2 Projection Methods, Orthographic
RepresentationDIN ISO 6428 Requirements for MicrocopyingDIN ISO
5455 Technical Drawings, ScaleDIN ISO 8015 Tolerancing PrincipleVDA
4953 Simplified CAD DrawingASME Y14.5M Dimensioning and
Tolerancing
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 7 v./of 38
82.9201-0000.4 / 807 / 01
All standards referenced in the text.
All national and international standards dealing with the
preparation of engineeringdrawings which do not conflict with the
standards mentioned in this document also apply.
Rules for the handling of systems (drawing administration
system, CAD systems, PCprograms etc.) will be advised by circulars
(standards department information bulletins).
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 8 v./of 38
82.9201-0000.4 / 807 / 01
3 FORMAT OF THE PRODUCT DOCUMENTATION
The product documentation may consist of several documents.
Example:
Master data sheet (always required)Drawing3D modelParts
listfurther references
3.1 Master data sheet[03]
The highest-order document in accordance with VDA 4953 is the
master data sheet. Themaster data sheet contains all data which can
be managed in the system. In order toavoid redundant data, many
entries which formerly appeared on the drawing will only
beindicated in the master data sheet in the future.The master data
sheet references all other documents required for a
completedescription of the product.Format and fields of the master
data sheet are described in para.10.2 of this standard.
3.2 Drawing
The drawing contains all geometrical data and specifications
required for productionsupplementally to the data of the master
data sheet. Only the necessary administrativedata is redundant,
being present on both the drawing and the master data sheet.Format
and fields of the drawing are described in para. 10.1.1 of this
standard.
3.3 3D model
The administrative data of a 3D model is covered by the master
data sheet.
3.4 Parts list
Format and fields of the parts list are described in para. 10.3
of this standard.
3.5 References
References are supplemental documents required for the
production, inspection ordelivery of the part, such as:
specifications, ATE standards, international standards
etc.References may also be documents which are important for the
further processing of thedocument or which serve documentation
purposes (such as data exchange guidelines,tolerance calculations,
studies, circuit diagrams etc.).
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 9 v./of 38
82.9201-0000.4 / 807 / 01
4 DRAWING SHEET SIZES AND DRAWING FRAMES[03]
The initial sheet sizes shall conform to ATE N 101 01.06. Always
use the smallest size
which still permits a clear representation. The sheet sizes A2
to A0 shall be preferred.
All drawing frames used require the approval of the User
Processes StandardsDepartment. Approved frames are usually filed in
the libraries of the correspondingsystems and/or the drawing
storage system.
5 PREPARATION OF DRAWINGS
5.1 Representations
Views, sections, details, dimensions and text or other
information for identical designs
shall generally be represented uniformly in accordance with the
national and
international standards and the supplemental ATE standards and
CAD definitions.For guidance, reference shall be made to drawings
which have already been releasedfor regular production
purposes.
5.2 Scales[03]
The scales to be used shall conform to DIN ISO 5455
corresponding to ATE N 100 01.07. Representations not drawn to
scale shall only be permitted by way ofexception (see ATE N 101
01.04).
5.3 Line widths
The line widths 0.5 (wide line) and 0.25 (narrow line) or 0.7
(wide line) and 0.35 (narrowline) of ATE N 101 01.25 shall be used
for all drawings.
5.4 Line spacing for microfilming
In many drawings, the line spacing may be so close that two
adjacent parallel lines areno longer distinguishable for reasons
inherent in the system.
For a merely pictorial representation of geometry without
dimensions, this is not critical(e.g. in assembly drawings).
In dimensioned drawings, scale-ups or scaled-up details shall be
represented such that -in accordance with DIN ISO 6428 - the
distance between two lines is not less than0.7 mm. The plot of a
microfilm blowback must be clearly legible.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 10 v./of 38
82.9201-0000.4 / 807 / 01
5.5 Administration, Procedures and Long-Term Archiving[03]
The documents stored in the released DIS are considered the
originals. All printouts ofsuch documents are thus uncontrolled
copies not covered by the Document Controlprocedure.
For long-term archiving purposes, each document is currently
archived in the IXOS system on magnetic-optical disks.
5.6 Lettering
5.6.1 Letter sizes [03]
Form B, vertical in accordance with ATE N 101 01.20 shall
generally be used for alllettering. If deviations are necessary for
reasons inherent in the system, the letter sizeshall be selected in
accordance with the implementation procedures of the CAD
system.
DIN 6776 corresponding to ATE N 101 01.20 applied for previous
drawings. This is nowinvalid and may no longer be used for new
designs.
If deviations are necessary for reasons inherent in the system,
the letter size shall beselected in accordance with the
implementation procedures of the CAD system.
Greek letters shall be represented by vertical lettering in
accordance with DIN EN ISO 3098-3. If this should not be possible
in CAD systems, follow theimplementation procedures of the CAD
system.
With the exception of symbols, units, surface finishes, material
and semi-finishedproduct specifications in accordance with the
applicable DIN/ISO or ATE standards, onlycapital letters should be
used on the drawings.
For the use of umlauts and special characters, follow the
implementation procedures ofthe respective CAD / management
system.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 11 v./of 38
82.9201-0000.4 / 807 / 01
The letter sizes to be used universally, irrespective of the
line group selected(see para. 5.3), are defined in the following
tables:
Lettering in
title block
Height of letters for all drawing sheetsizes[mm]
Document No. 5.0
Designation, 1st line 3.5
Additional designations 1 and 2 in 2nd line 2.0
Designation, 3rd line 2.0
Main scale 5.0
All other entries 3.5
Table of fits/allowances 3.5/2.5
Lettering and dimensioning in
drawing area
Height of letters for all drawing sheetsizes[mm]
Letters identifying sections, details,outlines, points etc.
5.0
Scale 5.0
Surface finish 3.5
Dimension figures 3.5
Tolerances for dimension figures 2.5/3.5
All other entries 3.5
5.6.2 Orthography in German-language drawings and parts
lists
The orthography of German texts in drawings and parts lists
shall conform to the latestedition of "DUDEN".
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 12 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
6 INFORMATION IN, OR RELATING TO, DRAWINGS
6.1 General[03]
The company language is English. German, the language of the
principal developmentlocation Germany, shall be preferred as second
mandatory language. Other decisionsare possible in special
cases.
As far as necessary, the drawings shall be lettered in two
languages. Depending on thedevelopment location, the text in
German, Portuguese, Japanese, Chinese or anotherlanguage shall be
legally binding. The respective language shall be incorporated into
thedrawing frames by the Central Standards Department.
All texts shall be entered in the appropriate fields as
specified in section 10 of thisstandard.
The designation of the part shall generally be given in 2
languages: in the languagelegally binding at the location in the
1st line and in the agreed second language in the3rd line.
The additional designation 1 or 2 may be used for an
abbreviation identifying a product,see also para. 6.9 of this
standard.
The designations and additional designations must always be
identical for drawing, partslist and master data sheet. For reasons
inherent in the system, the length ofdesignations is limited to 40
characters, that of additional designations to 30
characterseach.
Notes and instructions shall not be written directly into the
drawing area, but entered inthe notes columns provided for that
purpose (fields 3* and 4*).
In the drawing area, hexagons with 2-digit numbers allocated to
the notes in fields 3*and 4* shall be substituted for the texts.
The hexagons shall have a width across flats of10 mm and a line
width of 0.25 mm. Leaders, if required, shall be drawn from one
cornerof the hexagon to the corresponding item.
For texts with general applicability for the part drawn, the
hexagons with thecorresponding numbers shall be entered in field 7*
next to the title block.
If tables are provided in the drawing area, the table texts
shall be entered directly intothe tables.
Texts which appear on the body of the part drawn shall also be
placed on the body of thepart in the drawing (e.g. nameplates with
lettering).Related notes, such as height of letters etc., shall
again be identified by means of ahexagon.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 13 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
6.2 Tolerance studies / calculations
If tolerance studies / calculations are prepared for new
releases / new developments,these shall be filed with release level
F04 at the latest.
6.3 Workpiece edges
Workpiece edges shall be entered in accordance with ATE N 111
02.01.
The instruction Deburr in accordance with ATE N 111 06" is no
longer permitted for newdesigns.
6.4 Units
All units shall be SI units in accordance with ATE N 101
24.01.
6.5 Dimensions
6.5.1 Dimensions not drawn to scale[03]
Dimensions which are not drawn to scale are not permitted in
scaled CAD drawings.For exceptions see ATE N 101 01.04.Dimensions
not drawn to scale are indicated with an underlined dimension value
in theCatia V4 and Catia V5 CAD systems.
6.5.2 Dimensions for parts with surface protection
As specified in the title block (field 30*), all dimensions
apply to the condition afterSurface protection treatment. If
required - to preclude errors - the dimension beforesurface
treatment shall be stated in addition for fits.
6.5.3 Double dimensions (multiple dimensions)
Double dimensions may be used in a drawing by way of exception
and shall be identifiedby means of the symbol
( 4 mm)
In field 7*, such dimensions shall be identified by means of a
notes hexagon. The entryin the notes column (fields 3* and 4*) will
then read DOPPELMASS (DOUBLEDIMENSION), for example.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 14 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
6.5.4 Identification of characteristics with D and W
Identifications of engineering drawings for minimum requirements
which must bedocumented (D) and important characteristics (W) in
accordance with ATE N 101 00.02shall be implemented in the system
mask. The corresponding characteristics shall bemarked accordingly
in the drawing.References, such as specifications containing D or W
characteristics, must be listedin the field for notes (3/4*) in
addition to the master data sheet. To point out that thedocument
contains one or more such characteristics, D or W shall be added
inparentheses.
Example: Entry in notes field
ATE N 111 31.84 (W)
The number of D/W characteristics identified on the drawing
shall be indicated in themaster data sheet. In the above example,
the ATE standard would contribute 1 Wcharacteristic.
No identification is required in higher-ranking documents which
themselves contain noD or W characteristics.
6.6 Dimensional tolerances / tolerances of form and position
6.6.1 Tolerancing principle[03]
The tolerancing principle shall be indicated in the master data
sheet. This information isindispensable for all drawings containing
dimensions and all corresponding 3D models.All dimensions shall be
evaluated in accordance with the specified tolerancing
principle.Designers may choose between 4 options:
Standard Principle
ATE N 101 01.36 Envelope principle (not for new designs)
ATE N 101 01.38 Envelope principle
ASME Y14.5M Envelope principle
ISO 8015 Independency principle
ISO 8015 E Envelope principle
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 15 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
6.6.2 General tolerances
General tolerances shall always be specified if a drawing
contains dimension withouttolerance specifications. Dimensions
without tolerances do not exist. One exception fromthis rule are
theoretical dimensions, whose tolerances are determined by
otherinformation.
For this purpose, the title block offers the following
possibilities (see also 10.1.1):
Field No. Designation Entry
12* General tolerance forangles
Direct entry, e.g. 2/ or indirect entry byreference to a
standard orATE N 113 01.03
14* General tolerance for lineardimensions
Reference to a standard or ATE N 113 01.03, alternatively to a
table
13* Tables of generaltolerances for lineardimensions
3 alternate tables are made available inthe library of the CAD
system: JS14,JS15, JS17
Parts requiring specific materials and production processes
(such as castings and partsmade of elastomers) shall conform to the
applicable DIN/ISO or ATE standard.
6.6.3 Tolerances of form and position
General tolerances of form and position are defined in ATE N 113
01.02 (referencingDIN 7168 Part 2: 1981) or in ASME Y14.5M-1994.The
standard applicable for the respective location shall be defined by
the CentralStandards Department and fixed in the drawing frame in
field 27*. If the designer usesother specifications on the drawing,
then such other specifications shall prevail.
6.7 Projection methods
In accordance with DIN ISO 5456-2, the projection method shall
be indicated in field 24*of the drawing frame. The method shall be
defined by the Central StandardsDepartment.
6.8 References[03]
All standards (DIN, ISO), general technical specifications (ATE
N), tolerancecalculations, data exchange guidelines and other
documents required for the documentor the part in addition to the
drawing shall be indicated in the system screen under objectlinkage
in the document information set. They are then recorded as
References in themaster data sheet.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 16 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
6.9 Abbreviations identifying products
Products may be identified by means of abbreviations consisting
of a combination ofnumerals and letters. This characteristic for
identifying a product may be entered inaddition to the designation.
An overview of defined abbreviations is contained in ATE N101 04.XX
(depending on type of unit).
6.9.1 Units operating on mineral oil
Nur fr Minerall (for mineral oil only) shall be entered as
additional designation 1 or 2if a unit is designed for operation
with mineral oil, which means that all rubber parts, forexample,
must be made of a material which is resistant to mineral oil.
6.10 Project name
If drawings are exclusively prepared for a specific customer
project, then the system willenter the customer's project name in
field 16*.
6.11 Assembly drawings[03]
The individual parts shall be identified by means of item
numbers in accordance withATE N 101 01.33 corresponding to DIN ISO
6433. A parts list (bill of materials) shall beprepared for each
assembly drawing. If no parts list exists for the drawing,
NO PARTS LIST
shall be entered in the master data sheet as additional
designation.
6.12 Material and semi-finished product specifications in
drawings
Ensuring the functional integrity and arranging the laboratory
release of new materialsshall be the responsibility of the design
department. The material will then be releasedwith the release of
the drawing.Each new material / semi-finished product specification
must be requested from thestandards department in order to ensure
that the notation meets the requirements of thisstandard and will
then be made available to the design department in the material
database. This also applies to materials expected to meet an
additional requirement which isnot standardized as such.
For reasons inherent in the system, the material entry is made
exclusively in the masterdata sheet.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 17 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
6.12.1 Entry for semi-finished products and materials
The semi-finished product shall be entered in addition to the
material if the surface of thesemi-finished product is retained
without further processing in the range of at least onedimension or
if specific mechanical properties are required which are afforded
by thesemi-finished product.
The semi-finished product specifications shall be entered only
once (even if a choice isoffered between several alternate
materials).
6.12.2 Entry of the material without semi-finished product
specification
Only the material shall be entered for parts which are machined
to finished dimensionsall around if no mechanical properties of a
semi-finished product are required
6.12.3 Optional materials
Several material entries offer a choice between options. Such
options require no specialidentification.
6.12.4 Material specifications for rubber or plastic
parts[03]
For rubber or plastic parts, the corresponding materials from
the material data base shallbe entered in the master data sheet,
using the code numbers defined in ATE N 12502.XX / 126 01.XX.
An additional entry identifying the manufacturer is not
permitted.
Code numbers for new materials shall be defined by the User
Processes StandardsDepartment when the data of the materials is
known and has been released by theCentral Laboratory. Polymer
materials (e.g. plastics and rubber materials) which havenot
previously been used and are therefore also not entered in SAP-PLM
require aspecial release.Every manufacturer uses different mixture
compositions, even when the base polymerremains the same.
Corresponding tests are defined in order to ensure that the
materialsmeet the subsequent requirements. Release of the material
indicates that this is thecase. This also ensures that the material
is properly entered in the IMDS database.
For this purpose, ATE N 101 13.01 has been created as a process
procedure to ensurecorrect working procedures and define
responsibilities in the release procedure.
This standard is binding in accordance with the scope as per
section 1 of this standard.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 18 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
6.12.5 Material specifications for composite parts
Composite parts are parts which are permanently connected to
each other as a result oftheir processing or production method,
such as metal parts vulcanized or molded inposition.
Composite parts shall be depicted in a .2-drawing with separate
parts list. Insert andcomposite material shall be entered as
separate items. In the parts list, the insert shall appear with the
item code of the part. A .9-numbercorresponding to the .2-number
shall be defined for the composite material (e.g. rubberor
plastic). A .9-drawing need not be prepared. In the parts list, the
data record shall beidentified as ND (no drawing). The material
shall be obtained from the material database.
The entry in the parts list shall be made in accordance with
para. 8.3 of this standard.
Identification of the specifications as references shall be
implemented in accordancewith para. 6.8 of this standard.
6.12.6 Material specifications for purchased parts[03]
Purchased parts consisting of several individual parts for which
the materials cannot bedetermined will be entered as composite
parts in the master data sheet via the materialdata base of the PLM
system.If the data are not yet present in the PLM system, this is
detected automatically duringthe compulsory BOM-BOS check (Bill Of
Material - Bill Of Substance - Check). Thedata must then be
requested by the designer via the IMDS Task Management System.
6.12.7 Material specifications for electronic parts[03]
Electronic parts will be entered as electronic component in the
master data sheet viathe material database if the materials used
for such parts are not known. This applies forfully equipped and
soldered circuit boards. These are entered as an REC 019component
where the decision is made as to whether the material is entered as
PCB -high end printed circuit boards or as PCB - low end printed
circuit boards.
For further information on this, see the IMDS training
documentation and theTransaction Manual for CAS IMDS
Processing.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 19 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
6.13 Specification of a surface protection treatment[03]
Ensuring the functional integrity and arranging the laboratory
release of a new surfaceprotection treatment shall be the
responsibility of the design department. The surfaceprotection
treatment will then be released with the release of the
drawing.Each new surface protection treatment must be requested
from the User ProcessesStandards Department and will then be made
available to the design department in thesurface protection data
base of the system.
6.13.1 Material surface area for the surface protection
treatment
The surface area of a part in cm2 is required for the material
reporting of the plants if asurface protection coating is to be
applied. The surface area is used as a basis forcalculating the
weight of the chemical ingredients to be used for the surface
protectioncoating. The entry in the master data sheet is
exclusively made via the systems.
6.14 Released suppliers[03]
If only specific suppliers have been approved for a specific
part, then the suppliers shallbe obtained from the supplier data
base and entered via the systems. The textappearing in field 23*
Lieferant definiert / Supplier defined of the drawing then
reads:FEST / FIXED.
New entries in the supplier data base must be requested from the
User ProcessesStandards Department.
6.15 Specification of weight
The weight in grams of parts which can be weighed or calculated
must generally bespecified in each master data sheet and parts list
with release level F06 at the latest.However, this is not necessary
for documents which are not directly related to a part,such as
electric and hydraulic diagrams and software.
6.16 Other fields on the drawing
Explanations for the fields not explained up to this point will
be found in section 10 of thisstandard or the related other ATE
standards.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 20 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
6.17 Drawings of unmachined parts
6.17.1 Identification of unmachined parts
For the identification of unmachined parts with the
manufacturer's mark and date, theapplicable standard, i.e. ATE N
101 06.XX (depending on the design activity involved)shall be
entered in the master data sheet under References.
6.17.2 Mounting points
All points serving to mount a part in the tool shall be defined
as early as possible in thecourse of the development process. In
the drawing, the cross-sectioned areas shall beframed in accordance
with the geometry of the mounting arrangement (line
thickness0.25).
Examples:
The cross-sectioned area shall be entered in field 7* of the
drawing area together with itsnotes hexagon.
In fields 3* and 4*, this entry shall be explained as
follows:
Text in notes column Symbol identifying operation
Register point andmeasurement reference point
Centering point
Clamping point
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 21 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
6.18 Several item codes (part numbers) on one drawing
Drawings with two numbers must be distinguished from collective
drawings (chartdrawings). A separate master data sheet shall be
created for each item code. Drawingswith two numbers are used for
mirror-inverted parts if only one part is drawn.Collective drawings
(chart drawings) consist of a pictorial representation with a table
ofdimensions.
6.18.1 Drawings with two numbers
Only one drawing is prepared for parts which can be depicted by
mirror-invertedrepresentation (right-hand and left-hand design).
The first number identifies the part asdrawn (left-hand design, odd
number), the second number (right-hand design, evennumber) the
mirror-inverted design.Release and revision levels as well as
weight specification must be identical for bothdesigns.
Example: Left-hand design (1) and right-hand design (2)
6.18.2 Collective drawings[03]
A collective drawing (document carrier) consists of a pictorial
illustration of a part and atable listing the specific dimensions
of several parts. Each of these parts is assigned to aseparate item
code.
The creation of new collective drawings should be avoided
wherever possible.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 22 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
Where existing collective drawings are changed, the following
points must be compliedwith in SAP-PLM:
- The collective drawing document carrier (SZD) contains the
parts with similargeometry that are listed in the table of the
drawing as References. Note that only thelast version is entered in
the Object linkage screen.
- Material, weight and other information regarding the
respective material/part may notbe assigned to the document carrier
(collective drawing). This information mustalways be assigned to
the DIS of the item code itself. If this rule is not observed,
thematerial cannot be automatically identified and evaluated for
the Directive on End-of-Life Vehicles.
6.19 Referencing of drawings which must be changed
together[03]
Drawings which must be mutually taken into account in the event
of changes must havethe following entry in the notes columns
(fields 3* and 4*):
IN THE EVENT OF CHANGES, ALSO CHANGE XX.XXXX-XXXX.X
Note:
In older Catia V4 drawing frames, there used to be an entry
field in the drawing frame forentering a consecutive number in a
hexagon which was then put at the front in the notescolumns (fields
3* and 4*) as per the text - this entry field is no longer present
in thecurrent drawing frame. For this reason, this text shall be
entered without a consecutivenumber!
6.20 Drawing and parts list combined on one form (PLC)
A PLC is a combination of a drawing and a parts list on one
form. This representation
may no longer be used for new designs for EDP reasons.
F08 releases shall contain no PLC and no parts lists or parts
which cannot be set in thePLC system.When PLC drawings are changed,
they shall be separated into drawings and parts liststo make them
system-compatible.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 23 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
6.21 Supersedes entry[03]
If a new drawing or parts list supersedes a released drawing or
parts list, an entry withthe index of the document version (DV) and
a text comprising the words same numberfrom and the date of first
issue shall be made in field 18* (drawing), field 17* (part list)
orfield 6* (master data sheet).This entry may be abbreviated as
follows:
Example: German 09 GL. NR. V. 30.09.05
English 09 SM. NO. F. 30.09.05
The entry can be broken down as follows:
09 - The version number of the drawing being replaced (the new
version number would be 10 in this case)
SM. NO. F. - Same number from (date)
30.09.05 - Date of making this current version, according to
calendar date ofthis modified version.
Note:
This field must not be filled out for changes or a simple
increase in version number.
6.22 Photo releases
Photo releases are possible by way of exception to meet the
special requirements of theaftermarket. The photographs of the
parts shall be produced by means of digitalcameras in a readily
reproducible quality and set into the system. These drawings
willthen be released after providing them with a released drawing
frame and the necessaryadditional information.
6.23 Y-parts
In the past, drawings of parts and equipment for the German Army
were identified with a10 mm high Y in the title block. These parts
were subject to special regulations of theBundesamt fr Wehrtechnik
und Beschaffung. This identification will no longer be usedfor new
designs.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 24 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
7 DATA EXCHANGE
7.1 Data exchange with suppliers
The data exchange with suppliers is described in ATE N 101
75.01. If the proceduredescribed in that standard shall be used,
enter ATE N 101 75.01 in the master datasheet as reference.
7.2 Data exchange with customers[03]
Different rules defined in separate agreements apply to data
exchange with customers.
There are a series of customer-specific data exchange guidelines
which selectivelyexplain the special requirements for each customer
and the relevant procedures.
These data exchange guidelines have the number format ATE N 101
78.XX. The XXrepresents the respective customer number.
Example: The data exchange guideline for Daimler AG is ATE N 101
78.04
8 DESIGN PARTS LISTS
8.1 General[03]
The original parts list is the parts list stored in the PLM
system. It represents the startingpoint for further system
uses.
Each item code for which a parts list is required must have a
separate parts list.Double numbers require a separate parts list
for each number.
The parts list form is usually prepared in 2 languages,
depending on the developmentlocation.
Entries in a design parts list must cover all assemblies, parts
and auxiliary materialswhich are necessary for function, transport
and storage and included in the scope ofsupply.Packing and type of
delivery shall be ignored.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 25 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
8.1.1 Musts in all parts lists
For reasons inherent in the system, an entry must be made in the
following columns foreach listed part:- Item number, field 1*-
Quantity, fields 2*- Unit of quantity, field 3*- Item code, field
4*- Designation, field 5*.
If one of these fields is filled out, then all other fields must
be filled out as well.
8.1.2 Entries in the notes column[03]
The following entries can be made in the column headed NOTES
(field 6*):
Entry Meaning
PL Item code has or is a parts list
PLC Item code represents a combined drawing and parts list
STORAGE/SHIPMENTONLY
For storage and shipment only
OPTIONAL If several parts can be used interchangeably
Other texts if required
8.1.3 Parts lists without related drawings
In the case of assemblies or units for which only a parts list
exists and no drawing, thetext in field 14* of the parts lis must
read: O.Z./N.D. (ohne Zeichnung /no drawing). Thisentry is made
automatically by the system.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 26 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
Example:
8.1.4 Parts lists with two numbers
Parts lists with two numbers are no longer permitted.
8.1.5 Field for remarks applying to the complete parts list
In field 19*, remarks applying to the complete parts list can be
written via the system.
8.1.6 Entries in parts lists of collective drawings - chart
drawings - (Catia V4 only) [03]
If no separate drawing exists for a parts list contained in a
collective drawing, thefollowing note shall be entered in the field
for remarks applying to the complete parts list:
Example:
Note: In Catia V5 environment it will be no longer possible to
generate parts lists ofcollective drawings - without drawing.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 27 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
8.2 Parts list entries for unmachined parts
If a drawing of the unmachined part exists for a finished part,
then a parts list must beprepared for the finished part. In that
case, the parts list must contain the part number ofthe unmachined
part.
8.3 Parts list entries for composite parts
Composite parts are parts which are permanently connected to
each other as a result oftheir processing or production method.
Example: rubber part with integrated metal part
In order to permit the material to be allocated, the rubber part
without the metal partmust be given a separate item code (part
number) although it is only produced togetherwith the metal part.In
this case, N.D. (no drawing) will appear automatically in the
column headedO.Z./N.D. (field 20*) of the parts list.
Example:
8.4 Parts list entries for optional parts (alternative parts
list items)[03]
Optional parts or parts which are produced at different
locations with different machinesmay be entered in a parts list
under the following conditions:
The item number of the optional part is the same and appears
several times on the partslist.The unit of quantity must be
specified.The quantity shall be entered into the system such that
in the parts list the actual
quantity appears as 1, (for example in the case of pieces) and
all optional parts are
identified as 0.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 28 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
8.5 Parts list entries for standard parts and catalog
parts[03]
All standard parts and catalog parts of mechanical components
shall be given an itemcode and entered in the parts list.
All standard parts and catalog parts of electronic components
shall be given an itemcode from the E-CAD system and are
transferred to the parts list.
8.6 Parts list entries for development parts[03]
Looking on historical range of vision - status has been:
Parts which are not yet defined at the start of development work
for a product mayinitially be entered in a parts list as standard
dummies. The standard dummy must laterbe replaced by a real
part.The standard dummy will have the item code 84.4711-0815.0 and
will be automaticallydesignated as
F04 O. Z. WIRD NOCH FESTGELEGT / F04 N.D. T.B.D.
with the text appearing in the parts list with 40 characters.
This designation may not beoverwritten. The designation of the real
part may additionally be entered, in advance, inthe column for
notes.The item code may not be replaced by other entries, such as
ND (no drawing).
This proceeding becomes less interesting because in current
operational procedure ofCatia V5 it is necessary to create at first
a 3D-modell. Out of it the designer has to bleedoff the drawing.
Cause of this the processing with placeholder parts will become
lessimportant.
Important: For compliance with the end-of-life vehicle
regulation, a complete materialanalysis must be available as of
release level F07. Consequently, entering
the standard dummy in parts lists is not permissible once an
F07-release
has been issued.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 29 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
8.7 Units of quantity
For each item in the parts list, the appropriate unit of
quantity in accordance with thefollowing table shall be entered
under UNIT (field 3*).
In order to ensure system conformity, the SAP R3 units of
quantity shall be restricted tothe characters depicted in the
table.
valid no longerpermitted
no longerpermitted
Designation SI units SAP R3 UNIT SAP R2 UNIT IMS UNIT
Piece - ST (PC) ST (PC) 0
Set - SA (SET) SA (SET) 1
Pair - - PA 2
Kilogram kg KG KG 3
Millimeter mm MM MM 4
Ton (metric) t TO TO 5
Liter l L L 6
Meter m M M 7
Square meter m M2 M2 8
Cubic meter m M3 M3 9
Dozen - - DT 10
Gross - - GO 11
Hour h H H 12
Gram g G G/GR 13
Decimeter dm DM DM 14
Square decimeter dm DM2 D2 15
Cubic decimeter dm CDM D3 16
Centimeter cm CM CM 17
Square centimeter cm CM2 C2 18
Cubic centimeter cm CM3 C3 19
Micrometer :m - UM 20
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 30 v./of 38
* see pages 31 to 3782.9201-0000.4 / 807 / 01
9 CUSTOMER DRAWINGS
9.1 Preparation of customer drawings
(see also Job Instruction 1 to Organizational Procedure
4/75)
9.2 Special customer requirements[03]
To meet special customer requirements, different .6-drawings of
parts, units andaggregates shall be prepared for each customer.
Among other things, these shallcontain all installation and mating
dimensions, representations with item codes, materialand surface
protection specifications and the item code of the customer, as may
berequired.
If desired by the customer, the data from the master data sheet
must again betranscribed to the drawing.
The Continental purchase order number shall be indicated on the
drawing.
All drawings of parts contained in customer drawings can be
identified as follows via thenotes columns (fields 3* and 4*):
IN THE EVENT OF CHANGES ALSO CHANGE .6
Customer frames for special customers which do not conform to
the CAS standard willbe found in the corresponding system
libraries.
10 FORMS
All forms described in this standard have the same shape, size
and meaning of the fieldsworldwide. For explanations, the forms
valid at the Frankfurt location are used by way ofexample.
10.1 Drawing frames[03]
All drawing frames require the approval of the User Processes
Standards Department.
Three different drawing frames are available at this time (see
also section 4 of thisstandard):
- the standard frame for all normal applications - the standard
customer frame for all customer drawings without special
customer
frame permitting a customer title block to be inserted above the
ContinentalAutomotive title block
- the frame for studies and other representations
Special customer frames are defined by the customer and
therefore not covered by thisstandard.
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 31 v./of 38
82.9201-0000.4 / 807 / 01
10.1.1 Drawing frame - layout[03]
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 32 v./of 38
82.9201-0000.4 / 807 / 01
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 33 v./of 38
82.9201-0000.4 / 807 / 01
The following table lists the fields in the drawing frame with
the item numbers assignedto them and their meanings.
No. Meaning
1 Drawing area for geometry etc.
2 Columns for numbers of notes referenced in the drawing
3 Notes in English
4 Notes in language of development location
5 Space for representations on a scale of 1:1 if the drawing is
drawn to a differentscale
6 Space for symbols for workpiece edges in accordance with ATE N
111 02.01
7 Space for note numbers in hexagons for the complete part, from
right to left
8 Field for fits occurring in the drawing, all entries with 3
digits after the decimalpoint
9 Field for identification of CAD systems, with version and
model quality inaccordance with ATE N 101 01.04 if applicable
10 Field for release notes in accordance with ATE N 101
02.02
DV: Document version, identifies the change status of the
document.If the part is completely identical with the part/material
before the change, thechange is a change of the document version.
Changes of the document versionhave no effect on production.
RV: Revision Version, identifies the change status of the
material (the part).Material changes are all changes concerning the
material / part. This may be ageometrical change or a change of
material, treatment, surface finish. In anycase, this is a change
which affects production.
FR: Freigabe (release), indicates the current release level
11 Field for general tolerances for angular dimensions (para.
6.6.2)
12 Field for referencing standards for general tolerances if no
table is applicable(para. 6.6.2)
13 Table of general tolerances, several alternatives possible
(para. 6.6.2)
14 Main scale
15 Field for designating a part or product (2 languages
possible) (para. 6.1)
16 Field for project name
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 34 v./of 38
No. Meaning
82.9201-0000.4 / 807 / 01
17 Author of drawing or rather author of updated revisional
version, date and
department code (generated when DIS created or changed)
18 Field for supersedes entry in drawing (para 6.21) with
calendar date of currentdrawing version/modified version as
generated from DIS (No. 17 this table).
19 Field for document number(s), 2 numbers for
right-hand/left-hand design
20 Field for type of document, to distinguish different types
with identical numbers
21 Field for sheet number and number of sheets
22 Field for drawing sheet sizes
23 Field for entering the supplier
24 Projection method, depending on location (USA = 3, Europe,
Japan, Brazil = 1) inaccordance with DIN ISO 5456-2
25 Space for a customer title block
26 Field for entering the part document. For document types DPM
and DPS, thenumber in this field identifies a customer drawing for
a special customer
27 Field for entering the standard for general tolerances of
form and position (para.6.6.3)
28 Note drawing attention to the related master data sheet
29 Note stating which language is authoritative in the case of
entries in severallanguages
30 Note All dimensions after surface treatment
31 Copyright note, in 2 languages
32 Logo and company name
33 Company logo
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 35 v./of 38
82.9201-0000.4 / 807 / 01
10.2 Master data sheet - layout[03]
The following table lists the fields/blocks in the master data
sheet with the item numbersassigned to them and their meanings.
No. Meaning
1 Field for designation of the unit or assembly, in 2 languages,
if applicable, andabbreviation identifying a unit
2 Field for additional designation 1
3 Field for additional designation 2
4 Field for entering O.Z./N.D. if only the master data sheet
exists and no drawing
5 Field for master data sheet document number
6 Field for document number of predecessor master data sheet
and/or date of originalmaster data sheet
7 Field for sheet number and number of sheets of master data
sheet
8 Field for part document
9 Field for document type
10 Fields for name of author, date and department
11 Field for release notes (system entry)
12 Field for change notes (system entry)
13 Field for entering print date, hour and user
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 36 v./of 38
82.9201-0000.4 / 807 / 01
10.3 Parts list - layout[03]
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 37 v./of 38
82.9201-0000.4 / 807 / 01
The following table lists the fields/blocks in the master data
sheet with the item numbersassigned to them and their meanings.
No. Meaning
1 Column for item numbers, must be filled out consecutively, no
blank linesbetween successive items permitted
2 Column for quantities
3 Column for unit of quantity (see para. 8.7 of this standard
for permissible entries).
4 Column for item code of part (part number)
5 Column for designation
6 Column for notes, e.g.: ST (PC), STV (PLC), or other
additional information (seepara. 8.1.2 of this standard)
7 Field for release notes
8 Field for change notes
9 Field for abbreviation identifying the operating
department
10 Field for designation of unit or assembly, in 2 languages, if
applicable, andabbreviation identifying a unit
11 Field for parts list document number
12 Field for document type
13 Field for document part
14 Field for entering OHNE ZEICHNUNG (NO DRAWING) if only the
parts list existsand no drawing, see also para. 8.1.3 of this
standard (system entry)
15 Field for weight specification
16 Field for sheet number and number of sheets of the parts
list
17 Field for item code of predecessor parts list and /or date of
original parts list
18 Field for definition of O.Z./N.D.
19 Field for general remarks related to the parts list, see
para. 8.1.5 of this standard
20 Column for entering O.Z./N.D. if no drawing exists for the
parts list item (systementry)
21 Field for asterisk (*) if a changed version has been released
for the parts list item
-
Design Standards Doc. Type A T E
ENGINEERING DRAWINGS Doc. Num. N 101 01.01Rules of Preparation
Doc. Part 000 Doc.Ver. 03
Seite/Page 38 v./of 38
82.9201-0000.4 / 807 / 01
11 ENVIRONMENTALLY COMPATIBLE PRODUCT DEVELOPMENT[03]
The aims for environmentally compatible product development
described in ATE N 550 00.01 must be observed during design and
development.
Development checklists and tools for achieving these aims can be
found in the Intranetunder Environmental management in product
development.
For collaboration with suppliers, ATE N 550 00.02
Environmentally Compatible ProductDevelopment - Suppliers
applies.
On documentation/drawings for parts developed by a supplier,
there must be a referenceto environmentally compatible
development.
For this reason, all parts/products whose documentation is
provided to suppliers mustcontain a reference to ATE N 550 00.01
Sheet 200 / ATE N 550 00.02 Sheet 250Environmentally Compatible
Product Development in the DIS (link in the DIS). The ATE N is then
listed in References in the master data list for the
respectivesupplier.
This reference is particularly important for suppliers who
develop complicated purchasedparts/black box assemblies e.g.
electric motors etc.