ATA 191 Specifications • Physical Specifications, page 1 • Electrical Specifications, page 2 • Environmental Specifications, page 2 • Physical Interfaces, page 3 • Ringing Characteristics, page 3 • Software Specifications, page 4 • SIP Compliance Reference Information, page 5 Physical Specifications Table 1: Physical Specifications Specification Description FCC (Part 15 Class B), CE, ICES-003, A-Tick certification, Restriction of Hazardous Substances (RoHS), and UL Regulatory compliance DC input voltage: 5V DC at 2.0A maximum power consumption: 5W Switching type (100-240V): Automatic Power adapter: 100-240V and 50-60 Hz (26-34 VA) input with 1.8m cord Power supply Phone 1, phone 2, network, Problem Report Tool (PRT), and power Indicator lights and LEDs User Guide (online) Administration Guide (online) Regulatory Compliance and Safety Information guide (online) Documentation 3.98 x 3.98 x 1.10 in. (101 x 101 x 28mm) Dimensions (W x H x D) Cisco ATA 191 Analog Telephone Adapter Administration Guide for Cisco Unified Communications Manager 1
6
Embed
ATA 191 Specifications - Cisco€¦ · Cisco ATA 191 Analog Telephone Adapter Administration Guide for Cisco Unified Communications Manager 1. Description Specification Unitweight
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Tip/ring interfaces for each RJ-11 FXS port (SLIC)
70VRMS (typical, balanced ringing only)Ring voltage
20 HzRing frequency
Trapezoidal with 1.2 to 1.6 crest factorRing waveform
1400 ohm + 40μFRing load
Up to 5 REN per RJ-11 FXS portRinger equivalence number (REN)
Up to 200 ohms (plus 430-ohm maximum phone DCresistance)
Loop impedance
On-hook/off-hook characteristics
–47VOn-hook voltage (tip/ring)
24 mA (nominal)Off-hook current
The ATA 191 provides multiple impedance, such as 600ohm for American SKU, 900 ohm for European SKU,220 ohm (820 ohm || 120nF) for Australian SKU, andso on.
RJ-11 FXS port terminating impedance option
Cisco ATA 191 Analog Telephone Adapter Administration Guide for Cisco Unified Communications Manager 3
Configurable for two sets of frequencies and single set of on/offcadence
Call progress tones
DTMF tone detection and generationDual-tone multifrequency (DTMF)
Fax pass-through and T.38 fax relay mode.
V34 fax is supported for pass-through mode. Success of faxtransmissions up to 33.6 kb/s depends on network conditions, andfax modem/fax machine tolerance to those conditions. The networkmust have reasonably low network jitter, network delay, andpacket-loss rate.
The ATA 191 only supports T38 Fax Relay Version 0 (G3).
Fax
• Echo canceler for each port
• 8 ms echo length
• Nonlinear echo suppression (ERL > 28 dB for frequency = 300to 2400 Hz)
• Convergence time = 250 ms
• ERLE = 10 to 20 dB
• Double-talk detection
Line-echo cancellation
RFC 2833 AVT tones for SIP
Cannot transmit RFC 2833 and in-band signaling,simultaneously.
Cisco ATA 191 Analog Telephone Adapter Administration Guide for Cisco Unified Communications Manager4
ATA 191 SpecificationsSoftware Specifications
SpecificationDescription
Encryption for TFTP configuration filesSecurity
• G.729A, G.729AB
• G.711A-law
• G.711µ-law
Voice coder-decoders (codecs)
• Voice activity detection (VAD)
• Comfort noise generation (CNG)
• Dynamic jitter buffer (adaptive)
Voice features
SIP (RFC 3261)Voice-over-IP (VoIP) protocols
SIP Compliance Reference InformationInformation on how the ATA 191 complies with the IETF definition of SIP as described in RFC 2543 is foundat the following URL:
http://www.ietf.org/rfc/rfc2543.txt
Cisco ATA 191 Analog Telephone Adapter Administration Guide for Cisco Unified Communications Manager 5
ATA 191 SpecificationsSIP Compliance Reference Information