ISDN DIGITAL TELEPHONE SET ISDN DIGITAL TELEPHONE SET ISDN DIGITAL TELEPHONE SET ISDN DIGITAL TELEPHONE SET ISDN DIGITAL TELEPHONE SET ASSISTANT ASSISTANT ASSISTANT ASSISTANT ASSISTANT LIPTOVSKÝ HRÁDOK, a. s. TLH 99-003.1 * Producer reserves the right to change technical parameters of products. Services and capabilties of digital telephone set ASSISTANT Functions 1. Ten-digit memory for personal abbreviated dialling. 2. Redialling. 3. Selection from 10 types of ringers and regulation of their loudness level. 4. Different types of acoustic operation. 5. Keys for speech power regulation of call for telephone receiver and loudspeaker. 6. Notebook (NOTES). 7. Personal data protection code. 8. Dialling when telephone handset is hung up. 9. Display of actual date and time. 10. Do not disturb! 11. Dual-tone multifrequency pulsing, 12. Calling party identification presentation (CLIP), Calling party identification restriction (CLIR). 13. Connected party identification presentation (COLP), Connected party identification restriction (COLR). 14. Multiple subscriber’s number (MSN). 15. Portability of telephone set (TP). 16. Holding of a call (HOLD). 17. Three party group connection (3PTY). 18. Call accounting information (AOC). 19. Call waiting (CW). 20. Call forwarding (CFU, CFB, CFNR). 21. Malicious call interception (MCID). 22. User-to-user signalling (UUS) 23. Information about 10 outstanding incoming calls 24. Discreet reject of incoming call 25. Keypad protocol 26. Completion of Call To Busy Subscriber 27. Completion of Call No Reply 28. Call transfer (ECT) 29. Blocking of outgoing calls (5 different levels) 30. Emergency dialling possibility (5 diffrent numbers) 31. Filtering of incoming calls Technical parameters Display: 2x16-character alphanumeric display Keys: 12 digit selection keys 13 stable function keys System interface: 1. Two-wire connection - variants: Upo with range of max. 3 km Upn with range of max. 1 km 2. Four-wire connection to the bus So with range from 500 to 1000 m according to configuration. Dimensions: height 90 mm width 160 mm depth 220 mm Connection: from the side of telephone set - miniwestern connector (RJ 45), from the side of network - in accordance with standards valid in SR Connection of analog telephone terminal equipment (TA a/b) Connection cable: 3 m standard length Power supply: 40 V - from exchange or network termination. Emergency operation: ASSISTANT with So interface via switch over „+“ key for increase of output acoustic signal level of DTS: speech signal, acoustic signals, ringing. „-“ key for decrease of output acoustic signal level of DTS: speech signal, acoustic signals, ringing. LOUDSPEAKING OPERATION / LISTENING-IN, an indicator light key for putting a digital telephone set into loudspea- king operation without lifting a handset or for putting it into loud listening-in condition during quiet operation. SWITCHING OFF A MICROPHONE, an indicator light key for putting a digital telephone set into a mute condition (switched-off acoustic inputs in quiet and loudspeaking operation) during all call modes. HOLD/THREE PARTY CONFERENCE CALL, an indicator light key for activation of HOLD and 3PTY service REDIAL , a dialling of last called number is activated by this key. RELEASE, a key for release of digital telephone set to idle condition from any of its actions (calling, memory reviewing, programming). RETURN, an indicator light key for return to the held party. INFORMATION, an indicator light key for gaining information about memory set-up of digital telephone set. WARNING, a wrong manipulation or overflow of control timer during communicating with communication system. CONNECTION, an indicator light to indicate an establishment of protocol connection with communication system - „You can dial“. RIGHT SHIFT, a key for shifting a presentation shown on the display to the right. OK, a key for confirmation of display presentation or parameters entered into memory of digital telephone set. LEFT SHIFT, a key for shifting a presentation shown on the display to the left. Meaning of stable function keys and indicator lights Producer: Liptovský Hrádok a. s., 033 17 Liptovský Hrádok, SLOVAK REPUBLIC tel.: +421-44-5201 111, fax: +421-44-5222 391 e-mail:[email protected]www.teslalh.sk Certified by DQS DIN EN ISO 9001 Reg. No.: 052 881-01 ISDN S o bus PC with ISDN card Network termination ISDN telephone set ASSISTANT ISDN telephone set ASSISTANT U PBX or public switch Signalling Q.SIG DSS1 U Fig.: Practical use of ISDN telephone set „ASSISTANT“ drawing number line interface Upo So 3FP 251 53.605 ❋ 3FP 251 53.606 ❋ Produced versions of digital telephone set ASSISTANT MESSAGES, an indicator light key for viewing and activating of user’s text information. It is determined for using ISDN (Integrated Services Digital Network) services and complies with all international standards and recommendations. It enables to an user to use services provided by such network. It is produced in different versions which varries in the type of line interface. Digital telephone set ASSISTANT is designed for use of all facilities and full performance of digital telephone exchanges. It provides a high comfort to users during telephone communication with variety of selectable services including ISDN services. It is connected to service lines corresponding to EuroISDN standards with the basic access.
2
Embed
ASSISTANT - webzdarmaASSISTANT ASSISTANT LIPTOVSKÝ HRÁDOK, a. s. TLH 99-003.1 * Producer reserves the right to change technical parameters of products. Services and capabilties of
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
ISD
N D
IGIT
AL
TE
LE
PH
ON
E S
ET
ISD
N D
IGIT
AL
TE
LE
PH
ON
E S
ET
ISD
N D
IGIT
AL
TE
LE
PH
ON
E S
ET
ISD
N D
IGIT
AL
TE
LE
PH
ON
E S
ET
ISD
N D
IGIT
AL
TE
LE
PH
ON
E S
ET
AS
SIS
TA
NT
AS
SIS
TA
NT
AS
SIS
TA
NT
AS
SIS
TA
NT
AS
SIS
TA
NTL
IPT
OV
SK
Ý H
RÁ
DO
K, a
. s.
TL
H 99-003.1
* Producer reserves the right to change technical parameters of products.
Se
rvic
es a
nd
ca
pa
biltie
s o
f dig
ital te
lep
ho
ne
se
t AS
SIS
TA
NT
Functions1.Ten-digit m
emory for personal abbreviated dialling.
2.Redialling.3.Selection from
10 types of ringers and regulation of their loudness level.4.Different types of acoustic operation.5.Keys for speech pow
er regulation of call for telephone receiver and loudspeaker.6.Notebook (NOTES).7.Personal data protection code.8.Dialling w
hen telephone handset is hung up.9.Display of actual date and tim
e.10.Do not disturb!11.Dual-tone m
ultifrequency pulsing,12.Calling party identification presentation (CLIP), Calling party identification restriction (CLIR).13.Connected party identification presentation (COLP), Connected party identification restriction (COLR).14.M
ultiple subscriber’s number (M
SN).15.Portability of telephone set (TP).16.Holding of a call (HOLD).17.Three party group connection (3PTY).18.Call accounting inform
ation (AOC).19.Call w
aiting (CW).
20.Call forwarding (CFU, CFB, CFNR).
21.Malicious call interception (M
CID).22.User-to-user signalling (UUS)23.Inform
ation about 10 outstanding incoming calls
24.Discreet reject of incoming call
25.Keypad protocol26.Com
pletion of Call To Busy Subscriber27.Com
pletion of Call No Reply28.Call transfer (ECT)29.Blocking of outgoing calls (5 different levels)30.Em
ergency dialling possibility (5 diffrent numbers)
31.Filtering of incoming calls
Technical parameters
Display:2x16-character alphanum
eric displayKeys:
12 digit selection keys13 stable function keys
System interface:1. Tw
o-wire connection - variants:
Upo with range of m
ax. 3 kmUpn w
ith range of max. 1 km
2. Four-wire connection to the bus So w
ith rangefrom
500 to 1000 m according to configuration.
Dimensions:height
90 mm
width
160 mm
depth220 m
mConnection:from
the side of telephone set - miniw
estern connector (RJ 45),from
the side of network - in accordance with standards valid in SR
Connection of analog telephone terminal equipm
ent (TA a/b)Connection cable:3 m
standard lengthPower supply:
40 V - from exchange or netw
ork termination.
Emergency operation: ASSISTANT with So interface via sw
itch over
„+“ key for increase of output acoustic signal level of DTS: speech signal, acoustic signals, ringing.
„-“ key for decrease of output acoustic signal level of DTS: speech signal, acoustic signals, ringing.
LOUDSPEAKING OPERATION / LISTENING-IN, an indicator light key for putting a digital telephone set into loudspea-king operation without lifting a handset or for putting it into loud listening-in condition during quiet operation.
SWITCHING OFF A M
ICROPHONE, an indicator light key for putting a digital telephone set into a mute
condition (switched-off acoustic inputs in quiet and loudspeaking operation) during all call m
odes.
HOLD/THREE PARTY CONFERENCE CALL, an indicator light key for activation of HOLD and3PTY service
REDIAL , a dialling of last called number is activated by this key.
RELEASE, a key for release of digital telephone set to idle condition from any of its actions
(calling, mem
ory reviewing, program
ming).
RETURN, an indicator light key for return to the held party.
INFORMATION, an indicator light key for gaining inform
ation about mem
ory set-up of digitaltelephone set.
WARNING, a w
rong manipulation or overflow
of control timer during com
municating w
ithcom
munication system
.
CONNECTION, an indicator light to indicate an establishment of protocol connection w
ithcom
munication system
- „You can dial“.
RIGHT SHIFT, a key for shifting a presentation shown on the display to the right.
OK, a key for confirmation of display presentation or param
eters entered into mem
ory of digital telephone set.
LEFT SHIFT, a key for shifting a presentation shown on the display to the left.
10 types of ringers and regulation of their loudness level.4.Different types of acoustic operation.5.Keys for speech pow
er regulation of call for telephone receiver and loudspeaker.6.Notebook (NOTES)7.Personal data protection code.8.Dialling w
hen telephone handset is hung up.9.Display of actual date and tim
e.10.Do not disturb!11.Dual-tone m
ultifrequency pulsing,12.Calling party identification presentation (CLIP), Calling party identification restriction (CLIR).13.Connected party identification presentation (COLP), Connected party identification restriction (COLR).14.M
ultiple subscriber’s number (M
SN).15.Portability of telephone set (TP).16.Holding of a call (HOLD).17.Three party group connection (3PTY).18.Call accounting inform
ation (AOC).19.Call w
aiting (CW).
20.Call forwarding (CFU, CFB, CFNR).
21.Malicious call interception (M
CID).22.User-to-user signalling (UUS)23.Inform
ation about 10 outstanding incoming calls
24.Discreet reject of incoming call
25.Keypad protocol26.Com
pletion of Call To Busy Subscriber27.Com
pletion of Call No Reply28.Call transfer (ECT)29.Blocking of outgoing calls (5 different levels)30.Em
ergency dialling possibility (5 different numbers)
31.Filtering of incoming calls
32.Possibility to connect an extending keyboard(m
ax. 2 pcs)33.Possibility of data transm
ission via interface V.2434.Assem
bly of Director - Secretary Unit35.Possibility to connect analog telephone term
inal devices (telephone set, fax unit, modem
etc.)36.Possibility to build up a bus So w
ith DTS and interface Upn
Me
an
ing
of s
tab
le fu
nc
tion
ke
ys a
nd
ind
ica
tor lig
hts
Se
rvic
es a
nd
ca
pa
biltie
s o
f dig
ital te
lep
ho
ne
se
t MA
NA
GE
R
Technical parameters
Display:2x20-character alphanum
eric displayKeys:
12 digit selection keys12 stable function keys 3 keys w
ith selectable meaning
16 keys for abbreviated diallingSystem interface: 1. Tw
o-wire connection - variants:Upo w
ith range of max.3 km
Upn with range of m
ax.1 km2. Four-w
ire connection to the bus So with range from
500 to 1000 m according to configuration.
Control signalling via D channel:DSS1
Dimensions:height
90 mm
width
215 mm
depth220 m
mConnection:
from the side of telephone set - m
iniwestern connector (RJ 45),
from the side of netw
ork - in accordance with standards valid in SR
Connection of analog telephone terminal equipm
ent (TA a/b) (in preparatory state)Connection cable: 3 m
standard lengthPower supply:
40 V - from exchange or netw
ork termination.
Emergency operation: all types of DTS with So interface via sw
itch over
Fa
x G3
PC
with
ISD
N ca
rd
DE
CT
ba
sic sta
tion
PB
X o
r pu
blic
switch
So
Up
nS
o b
us
Syste
mfo
r PC
Ad
ap
tatio
nsyste
mU
po
a/b
ISD
N te
lep
ho
ne
set M
AN
AG
ER
ISD
N te
lep
ho
ne
set M
AN
AG
ER
with
bu
ilt-in N
T
ISD
N te
lep
ho
ne
set M
AN
AG
ER
with
bu
ilt-in a
/b a
da
pte
r
Fig.: Practical use of ISDN telephone set „MANAGER“
1. System for PC - transmission of files and data among PCs in ISDN - receiving and sending of fax messages of G3 group - remote access to LAN via ISDN - complementary services according to EuroISDN
2. Adaptation system - possibility to connect analog terminal devices (fax, telephone recording device etc.) to ISDN via a/b adapter - complementary services according to EuroISDN
DrawingLine
Terminal
Integr.netw.num
berinterface
adaptersterm
inationUp
SoTA-V.24
TA-a/bIN
T
3FP 251 53.608❋
3FP 251 53.609❋
3FP 251 53.610❋
❋
3FP 251 53.611❋
❋
3FP 251 53.612❋
❋
3FP 251 53.613❋
❋
3FP 251 53.614❋
❋
- in preparatory state
„+“ key for increase of output acoustic signal level of DTS: speech signal, acoustic signals, ringing.
„-“ key for decrease of output acoustic signal level of DTS: speech signal, acoustic signals, ringing.
MESSAGES, an indicator light key designed for activating, sending, receiving and
viewing of user’s text m
essages.
LOUDSPEAKING OPERATION / LISTENING-IN, an indicator light key for puttinga digital telephone set into loudspeaking operation during all call m
odes.
SWITCHING OFF A MICROPHONE, an indicator light key for putting a digital telephone set into a mute
condition (switched-off microphone in quiet and loudspeaking operation) during all call modes.
INFORMATION, an indicator light key for gaining inform
ation about mem
ory set-up ofdigital telephone set and for NOTES service in tim
e of established connection.
CONNECTION, an indicator light to indicate an establishment of
protocol connection with com
munication system
- „You can dial“.
WARNING, a w
rong manipulation or overflow
of control timer during
comm
unicating with com
munication system
.
KEYS FOR DIGIT DIALLING
RELEASE, a key for release of digital telephone set to idle condition from any of its
actions (calling, mem
ory reviewing, program
ming).
REDIAL , a dialling of last called number is activated by this key.
CONSULT CONNECTION, an indicator light key for control of consult (switched over)
connection between tw
o remote subscribers.
HOLD/THREE PARTY CONFERENCE CALL, an indicator light key for activation of HOLDand 3PTY service.
DISPLAY, your telephone set is equipped by two line alphanum
eric display
PROGRAMM
ABLE KEYS, three keys with selectable m
eaning (soft keys)
Left shift and right shift
KEYS for abbreviated dialling
LIP
TO
VS
KÝ
HR
ÁD
OK
, a. s
.
It is determined for m
anagers of companies and organizations in all
branches of industry, services, departments, public adm
inistration.
It facilitates work of m
anagers and their secretaries. It distinguishes
itself by its service comfort w
ith keys located lucidly and complem
ented
by LED
signalling. It is produced in different versions which w
arries in
the type of line interface and built-in adapters.
ISD
N D
IGIT
AL
TE
LE
PH
ON
E S
ET
MA
NA
GE
RD
igital telephone set MA
NA
GE
R is a high-duty and m
odern telephone set designed for
connection to private branch and public digital switching system