ART. nr Dimension - wood-lord.comwood-lord.com/documents/cutting_tools/PCD tools.pdf · Nr Dimension Typ D d S Z FPF 12 120 30/35/40 4 FPF 15 150 30/35/40 4 FPF 16 160 30/35/40 4

www.npol.com.pl 4 - 2

www.npol.com.pl

Posu

w w

m/m

in

Grubość w mm

Re-sharpening shank cutter in diamond, single tip Z=1, suitable for working on

chipboard panels, laminated, coated, surfaced, M.D.F., hard woods,

plastics, corian and polymers, and working as grooving bit on coated panels.

*CUTTING: D = straight, P = positive, N = negative.

ART. nr Dimension

right left D L1 L2 L3 d Z

EC1 0510R EC1 0510L 5 60 10 40 6 1

EC1 0612R EC1 0612L 6 60 12 40 6 1

EC1 0712R EC1 0712L 7 60 12 40 8 1

EC1 0812R EC1 0812L 8 65 12 40 8 1

EC1 0912R EC1 0912L 9 65 12 40 8 1

EC1 1015R EC1 1015L 10 70 15 40 10 1

EC1 1220R EC1 1220L 12 70 20 40 10 1

DIA ROUTER BIT Z=1 art. EC1


DIA ROUTER BIT Z=1 + 1 art. SC/SC2

Posu

w w

m/m

in

Grubość w mm

Re-sharpening shank cutter in diamond, single tip, one or two engaged cuts,

PCD height 4,5 mm, suitable for working on chipboard panels,

laminated, coated, M.D.F., hard woods, polymers, plastic materials, CORIAN,

HPL, etc. Excellent finishing.

ART. nr Dimension

Prawe Lewe D L1 L2 L3 d Z

SC 1625R SC 1625L 16 85 25 50 16 1+1

SC2 1625R SC2 1625L 16 85 25 50 16 2+1

SC 1825R SC 1825L 18 85 25 50 20 1+1

SC2 1825R SC2 1825L 18 85 25 50 20 2+1

SC 2034R SC 2034L 20 94 34 50 20 1+1

SC2 2034R SC2 2034L 20 94 34 50 20 2+1

SC 2243R SC 2243L 22 103 43 50 20 1+1

SC2 2243R SC2 2243L 22 103 43 50 20 2+1


DIA ROUTER BIT Z=1+1 art. EC2E

Posu

w w

m/m

in

Grubość w mm

Diamond shank cutter economic type with two helicoidal wings , PCD height

2,5 mm, suitable for working on chipboard panels, surfaced,

laminated, coated, M.D.F.

Positive/negative cutters, good finishing on the upper and lower side, low no-

isiness.

ART nr Dimension


EC2E 1225R EC2E 1225L 12 75 25 40 12 1+1

EC2E 1234R EC2E 1234L 12 85 34 40 12 1+1

EC2E 1625R EC2E 1625L 16 85 25 50 16 1+1

EC2E 1634R EC2E 1634L 16 94 34 50 16 1+1

EC2E 1643R EC2E 1643L 16 103 43 50 16 1+1

EC2E 1825R EC2E 1825L 18 85 25 50 20 1+1

EC2E 1834R EC2E 1834L 18 94 34 50 20 1+1

EC2E 1843R EC2E 1843L 18 103 43 50 20 1+1

EC2E 2025R EC2E 2025L 20 85 25 50 20 1+1

EC2E 2034R EC2E 2034L 20 94 34 50 20 1+1

EC2E 2043R EC2E 2043L 20 103 43 50 20 1+1

EC2E 2052R EC2E 2052L 20 112 52 50 20 1+1

EC2E 2061R EC2E 2061L 20 121 61 50 20 1+1


DIA ROUTER BIT Z=1 + 1 art. EC3E

Posu

w w

m/m

in

Grubość w mm

Shank cutter in diamond economic type with three helicoidal wings, height

PCD 2,5 mm, suitable for working on chipboard panels, coated,

laminated, M.D.F.

Positive /negative cutters, good finishing on the upper and lower side, low

noisiness

ART. nr Dimension


EC3E 1025R EC3E 1025L 10 75 25 40 12 1+1

EC3E 1225R EC3E 1225L 12 75 25 40 12 1+1

EC3E 1234R EC3E 1234L 12 85 34 40 12 1+1

EC3E 1625R EC3E 1625L 16 85 25 50 16 1+1

EC3E 1634R EC3E 1634L 16 94 34 50 16 1+1

EC3E 1643R EC3E 1643L 16 103 43 50 16 1+1

EC3E 1825R EC3E 1825L 18 85 25 50 20 1+1

EC3E 1834R EC3E 1834L 18 94 34 50 20 1+1

EC3E 1843R EC3E 1843L 18 103 43 50 20 1+1

EC3E 2025R EC3E 2025L 20 85 25 50 20 1+1

EC3E 2034R EC3E 2034L 20 94 34 50 20 1+1

EC3E 2043R EC3E 2043L 20 103 43 50 20 1+1

EC3E 2052R EC3E 2052L 20 112 52 50 20 1+1

EC3E 2061R EC3E 2061L 20 121 61 50 20 1+1


DIA ROUTER BIT Z=2+2 art. EC4E

Posu

w w

m/m

in

Grubość w mm

Shank cutter in diamond economic type , with four helicoidal wings, two cut-

ters engaged on all working capacity, height PCD 2,5 mm,

suitable for working on chipboard panels,coated, laminated, M.D.F.

Positive /negative cutters, excellent finishing, good feeding speed, low

noisiness.

ART. Nr Dimension


EC4E 1225R EC4E 1225L 12 75 25 40 12 2+1

EC4E 1625R EC4E 1625L 16 85 25 50 16 2+1

EC4E 1634R EC4E 1634L 16 94 34 50 16 2+1

EC4E 1825R EC4E 1825L 18 85 25 50 20 2+1

EC4E 1834R EC4E 1834L 18 94 34 50 20 2+1

EC4E 1843R EC4E 1843L 18 103 43 50 20 2+1

EC4E 2025R EC4E 2025L 20 85 25 50 20 2+1

EC4E 2034R EC4E 2034L 20 94 34 50 20 2+1

EC4E 2043R EC4E 2043L 20 103 43 50 20 2+1

EC4E 2052R EC4E 2052L 20 112 52 50 20 2+1

EC4E 2061R EC4E 2061L 20 121 61 50 20 2+1


DIA ROUTER BIT Z=3 + 1 art. ECXE

Posu

w w

m/m

in

Grubość w mm

Shank cutter in diamond economic type with three helicoidal wings uninterrup-

ted, two engaged cutters, height PCD 2,5 mm, suitable for

working on chipboard panels , coated, laminated, M.D.F..

Positive /negative cutters, excellent finishing, good feeding speed, low noisi-

ness

ART. nr Dimension


ECXE 1227R ECXE 1227L 12 75 27 40 12 3+1

ECXE 1236R ECXE 1236L 12 85 36 40 12 3+1

ECXE 1627R ECXE 1627L 16 86 27 50 16 3+1

ECXE 1636R ECXE 1636L 16 95 36 50 16 3+1

ECXE 1645R ECXE 1645L 16 105 45 50 16 3+1

ECXE 1836R ECXE 1836L 18 95 36 50 20 3+1

ECXE 1845R ECXE 1845L 18 105 45 50 20 3+1

ECXE 2056R ECXE 2056L 20 116 56 50 20 3+1

ECXE 2267R ECXE 2267L 22 127 67 50 20 3+1


DIA ROUTER BIT Z=3+3 art. RX3S

Re-sharpening shank cutter in diamond with six helicoidal wings uninterrup-

ted, three engaged cutters on all working capacity, height PCD

4,5 mm, suitable for working on chipboard panels, coated, laminated, M.D.F.

Positive /negative cutters, high feeding speed, excellent

finishing, low noisiness.

ART. nr Wymiary


RX3S 2027R RX3S 2027L 20 87 27 50 20 3+3

RX3S 2236R RX3S 2236L 22 96 36 50 20 3+3

RX3S 2527R RX3S 2527L 25 97 27 55 25 3+3

RX3S 2536R RX3S 2536L 25 105 36 55 25 3+3

RX3S 2546R RX3S 2546L 25 115 46 55 25 3+3

RX3S 2555R RX3S 2555L 25 120 55 55 25 3+3


DIA ROUTER BIT Z=4 + 2 art. RX4 +C

Re-sharpening shank cutter in diamond with four wings uninterrupted, two

engaged cutters on all working capacity, height PCD 4,5 mm,

suitable for working on chipboard panels, coated, laminated, M.D.F.

Positive /negative cutters, high feeding speed, excellent finishing, low

noisiness.

ART. nr Wymiary


RX4 2225R RX4 2225L 22 86 25 50 20 4+2

RX4 2231R RX4 2231L 22 91 31 50 20 4+2

RX4 2236R RX4 2236L 22 96 36 50 20 4+2

RX4 2241R RX4 2241L 22 101 41 50 20 4+2

RX4 2247R RX4 2247L 22 106 47 50 20 4+2

RX4 2552R RX4 2552L 25 121 52 55 25 4+2

RX4 2557R RX4 2557L 25 125 57 55 25 4+2

RX4 2563R RX4 2563L 25 131 63 55 25 4+2

RX4 2568R RX4 2568L 25 135 68 55 25 4+2

ART. nr Wymiary Ilość

ostrzy


RX4C 2225R RX4C 2225L 22 86 25 50 20 4+2

RX4C 2231R RX4C 2231L 22 91 31 50 20 4+2

RX4C 2236R RX4C 2236L 22 96 36 50 20 4+2

RX4C 2241R RX4C 2241L 22 101 41 50 20 4+2

RX4C 2247R RX4C 2247L 22 106 47 50 20 4+2

RX4C 2552R RX4C 2552L 25 121 52 55 25 4+2

RX4C 2557R RX4C 2557L 25 125 57 55 25 4+2

RX4C 2563R RX4C 2563L 25 131 63 55 25 4+2

RX4C 2568R RX4C 2568L 25 135 68 55 25 4+2


DIA ROUTER BIT Z=4+2 art. RX4S+C

Re-sharpening shank cutter in diamond with four wing uninterrupted , two en-

gaged cutters on all working capacity, height PCD 4,5 mm,

drilling tip in PCD, suitable for working on chipboard panels, M.D.F. with thin

layers coatings or thin papers covered. Positive /negative

cutters, elevate feeding speed, excellent finishing and good wooden-chip

extraction due to the special geometry construction, low noisiness.

ART. nr Dimension


RX4S 2225R RX4S 2225L 22 86 25 50 20 4+2

RX4S 2231R RX4S 2231L 22 91 31 50 20 4+2

RX4S 2236R RX4S 2236L 22 96 36 50 20 4+2

RX4S 2241R RX4S 2241L 22 101 41 50 20 4+2

RX4S 2547R RX4S 2547L 25 116 47 55 25 4+2

RX4S 2552R RX4S 2552L 25 121 52 55 25 4+2

RX4S 2557R RX4S 2557L 25 125 57 55 25 4+2

RX4S 2563R RX4S 2563L 25 131 63 55 25 4+2

RX4S 2568R RX4S 2568L 25 135 68 55 25 4+2

ART. nr Dimension


RX4SC 2225R RX4SC 2225L 22 86 25 50 20 4+2

RX4SC 2231R RX4SC 2231L 22 91 31 50 20 4+2

RX4SC 2236R RX4SC 2236L 22 96 36 50 20 4+2

RX4SC 2241R RX4SC 2241L 22 101 41 50 20 4+2

RX4SC 2547R RX4SC 2547L 25 116 47 55 25 4+2

RX4SC 2552R RX4SC 2552L 25 121 52 55 25 4+2

RX4SC 2557R RX4SC 2557L 25 125 57 55 25 4+2

RX4SC 2563R RX4SC 2563L 25 131 63 55 25 4+2

RX4SC 2568R RX4SC 2568L 25 135 68 55 25 4+2


DIA ROUTER BIT Z=6 + 3 art. RX6+C

Re-sharpening shank cutter in diamond with six wings uninterrupted , three

engaged cutters on all the working capacity, height PCD 4,5 mm,

suitable for working on chipboard panels, coated, laminated, M.D.F.

Positive/negative cutters, very high feeding speed, excellent finishing on

all the thicknesses, low noisiness.

ART. nr Dimension


RX6 2525R RX6 2525L 25 86 25 40 25 6+3

RX6 2531R RX6 2531L 25 91 31 40 25 6+3

RX6 2536R RX6 2536L 25 96 36 50 25 6+3

RX6 2541R RX6 2541L 25 101 41 50 25 6+3

RX6 2547R RX6 2547L 25 116 47 50 25 6+3

RX6 2552R RX6 2552L 25 121 52 50 25 6+3

RX6 2557R RX6 2557L 25 131 57 50 25 6+3

RX6 2563R RX6 2563L 25 135 63 50 25 6+3

ART. nr Dimension


RX6C 2525R RX6C 2525L 25 86 25 40 25 6+3

RX6C 2531R RX6C 2531L 25 91 31 40 25 6+3

RX6C 2536R RX6C 2536L 25 96 36 50 25 6+3

RX6C 2541R RX6C 2541L 25 101 41 50 25 6+3

RX6C 2547R RX6C 2547L 25 116 47 50 25 6+3

RX6C 2552R RX6C 2552L 25 121 52 50 25 6+3

RX6C 2557R RX6C 2557L 25 131 57 50 25 6+3

RX6C 2563R RX6C 2563L 25 135 63 50 25 6+3


DIA ROUTER BIT Z=3+1 art. UL + C

Re-sharpening shank cutter in diamond with three continuous wings , three en-

gaged cutters on all working capacity, height PCD 4,5 mm,

suitable for working on chipboard panels, coated, laminated, M.D.F. Positive /

negative cutters, high feeding speed, excellent finishing

ART. nr Dimension


UL 2025R UL 2025L 20 87 25 50 20 3+1

UL 2030R UL 2030L 20 91 30 50 20 3+1

UL 2235R UL 2235L 22 96 35 50 20 3+1

UL 2240R UL 2240L 22 101 40 50 20 3+1

UL 2525R UL 2525L 25 98 25 55 25 3+1

UL 2530R UL 2530L 25 98 30 55 25 3+1

UL 2535R UL 2535L 25 104 35 55 25 3+1

UL 2540R UL 2540L 25 109 40 55 25 3+1

UL 2545R UL 2545L 25 114 45 55 25 3+1

UL 2550R UL 2550L 25 120 50 55 25 3+1

UL 2555R UL 2555L 25 125 55 55 25 3+1

UL 2562R UL 2562L 25 128 61 55 25 3+1

UL 2567R UL 2567L 25 133 66 55 25 3+1

ART. nr Dimension


ULC 2025R ULC 2025L 20 87 25 50 20 3+1

ULC 2030R ULC 2030L 20 91 30 50 20 3+1

ULC 2235R ULC 2235L 22 96 35 50 20 3+1

ULC 2240R ULC 2240L 22 101 40 50 20 3+1

ULC 2525R ULC 2525L 25 98 25 55 25 3+1

ULC 2530R ULC 2530L 25 98 30 55 25 3+1

ULC 2535R ULC 2535L 25 104 35 55 25 3+1

ULC 2540R ULC 2540L 25 109 40 55 25 3+1

ULC 2545R ULC 2545L 25 114 45 55 25 3+1

ULC 2550R ULC 2550L 25 120 50 55 25 3+1

ULC 2555R ULC 2555L 25 125 55 55 25 3+1

ULC 2562R ULC 2562L 25 128 61 55 25 3+1

ULC 2567R ULC 2567L 25 133 66 55 25 3+1


DIA ROUTER BIT DIA Z=4 + 4 art. TRPE

Re-sharpening shank cutter in diamond, helicoidal design , height PCD 4,5

mm, suitable for finishing working on chipboard panels, coated,

laminated, veneered, M.D.F. High feeding speed, excellent finishing of the

panel, low noisiness

ART. nr Dimension


TRPE 50254R TRPE 50254L 50 85 25 50 20 4+4

TRPE 50252R TRPE 50252L 50 90 25 55 20 4+2

TRPE 50354R TRPE 50354L 50 95 35 50 20 4+4

TRPE 50352R TRPE 50352L 50 100 35 55 20 4+2

TRPE 50454R TRPE 50454L 50 105 45 50 20 4+4

TRPE 50452R TRPE 50452L 50 110 45 55 20 4+2


DIA ROUTER Z=1 art. EC3E RB

Shank cutter in diamond economic type with copying bearing, three uninterrup-

ted wings, height PCD 2,5 mm, suitable for trimming and

routing on chipboard panels, coated, M.D.F. Positive /negative cutters, good fi-

nishing both sides of panel, low noisiness

ART. nr Dimension

Prawe D1 L1 L2 d Z

EC3E 12725RB 12,7 81 25 12 1+1

EC3E 12735RB 12,7 91 35 12 1+1

EC3E 12743RB 12,7 101 43 12 1+1


PROFILED DIA ROUTER Z=2 + 2 art. FSP

"T" slot shank cutter diamond Z=2+2 suitable for carrying out aluminium profi-

le grooving on chipboard panels, surfaced, MDF, excellent

upper finishing of the panel, low noisiness.

ART. nr Wymiary Ilość

ostrzy

Prawe D L1 L2 L3 d Z

FSP A 21,5 80 9,6 50 20 2+2

FSP B 24 80 7 50 20 2+2

FSP C 26 80 7 50 20 2+2

FSP D 27 80 7 50 20 2+2

FSP E 30,3 80 7,35 50 20 2+2


PROFILED ROUTER DIA


DIAMOND SAW BLADES

Diamond saw blades for panel machine

Diamond scoring saw blades

Adjustable diamond scoring saw blades


DIA CUTTER FOR EDGEBANDING art. TRBE

ART. Nr Dimension

Prawe Lewe D S d Z

TRBE 840R TRBE 840L 80 40 30 3+3

TRBE 848R TRBE 848L 80 48 30 3+3

TRBE 855R TRBE 855L 80 55 30 3+3

TRBE 865R TRBE 865L 80 65 30 3+3

TRBE 1040R TRBE 1040L 100 40 30 3+3

TRBE 1048R TRBE 1048L 100 48 30 3+3

TRBE 1055R TRBE 1055L 100 55 30 3+3

TRBE 1065R TRBE 1065L 100 65 30 3+3

TRBE 1240R TRBE 1240L 125 40 30 3+3

TRBE 1248R TRBE 1248L 125 48 30 3+3

TRBE 1255R TRBE 1255L 125 55 30 3+3

TRBE 1265R TRBE 1265L 125 65 30 3+3

Jointing cutter in diamond with helicoidal wings, height PCD 2,5 mm, suitable for

working on chipboard panels, coated, laminated, veneered,

M.D.F., it can be used on edgebanding machines. Excellent finishing, low noisi-

ness.


ART. Nr Dimension

Prawe Lewe D S d Z

TRBA 840R TRBA 840L 80 40 30 4+4

TRBA 848R TRBA 848L 80 48 30 4+4

TRBA 855R TRBA 855L 80 55 30 4+4

TRBA 865R TRBA 865L 80 65 30 4+4

TRBA 1040R TRBA 1040L 100 40 30 4+4

TRBA 1048R TRBA 1048L 100 48 30 4+4

TRBA 1055R TRBA 1055L 100 55 30 4+4

TRBA 1065R TRBA 1065L 100 65 30 4+4

TRBA 1240R TRBA 1240L 125 40 30 4+4

TRBA 1248R TRBA 1248L 125 48 30 4+4

TRBA 1255R TRBA 1255L 125 55 30 4+4

TRBA 1265R TRBA 1265L 125 65 30 4+4

Jointing cutter in diamond with helicoidal wings, height PCD 2,5 mm, suitable for

working on chipboard panels, coated, laminated, veneered,

M.D.F., it can be used on edgebanding machines. Excellent finishing, low noisi-

ness.

DIA CUTTER FOR EDGEBANDING art. TRBA


DIA CUTTER FOR EDGEBANDING art. TRS

ART. Nr Dimension

Prawe/Lewe D S d Z

TRS 18205 R/L 180 20/38 30/35/40 5+5

TRS 18206 R/L 180 20/38 30/35/40 6+6

TRS 18255 R/L 180 25/48 30/35/40 5+5

TRS 18256 R/L 180 25/48 30/35/4 6+6

TRS 20205 R/L 200 20/38 30/35/40 5+5

TRS 20206 R/L 200 20/38 30/35/40 6+6

TRS 20255 R/L 200 25/48 30/35/40 5+5

TRS 20256 R/L 200 25/48 30/35/4 6+6

Re-sharpening and adjustable jointing cutter in diamond , height PCD 5 mm,

made in two pieces adjustable by spacer rings , suitable for

working on chipboard panels,coated, laminated, veneered, M.D.F., can be used

on squaring and edgebanding machines. Excellent



DIA CUTTER FOR EDGEBANDING art. TRBR

Re-sharpening and adjustable jointing cutter in diamond , height PCD 5 mm,

made in two pieces adjustable by spacer rings , suitable for

working on chipboard panels, coated, laminated, veneered, M.D.F., can be used

on squaring and edgebanding machines. Excellent


ART. Dimension

Prawe Lewe D S d Z

TRBR 820R TRBR 820L 80 20/38 25/30 3+3+3+3

TRBR 825R TRBR 825L 80 25/48 25/30 3+3+3+3

TRBR 830R TRBR 830L 80 30/58 25/30 3+3+3+3

TRBR 1020R TRBR 1020L 100 20/38 25/30 3+3+3+3

TRBR 1025R TRBR 1025L 100 25/48 25/30 3+3+3+3

TRBR 1030R TRBR 1030L 100 30/58 25/30 3+3+3+3

TRBR 1220R TRBR 1220L 125 20/38 25/30 3+3+3+3

TRBR 1225R TRBR 1225L 125 25/48 25/30 3+3+3+3

TRBR 1230R TRBR 1230L 125 30/58 25/30 3+3+3+3


DIA TRIMMING CUTTER art. FSBP

Re-sharpening trimming cutter for chanfering off the edges, height PCD 4,5 mm,

suitable for working on chipboard panels laminated, coated,

veneered, M.D.F.,. it can be used on edgebanding machines. Excellent finishing,

low noisiness.

ART. Dimension

Prawe Lewe D S d Z

FSBP 70164R FSBP 70164L 70 16 10 4

FSBP 70166R FSBP 70166L 70 16 10 6

FSBP 70204R FSBP 70204L 70 20 10 4

FSBP 70206R FSBP 70206L 70 20 10 6

FSBPH 7084R FSBPH 7084L 70 HSK25 8 4





DIA TRIMMING CUTTER art. FSBI




low noisiness.

ART. Dimension

Prawe Lewe D S d < Z

FSBI 73164R FSBI 73164L 73 16 10 20 4

FSBI 73166R FSBI 73166L 73 16 10 20 6

FSBI 73204R FSBI 73204L 73 20 10 20 4

FSBI 73206R FSBI 73206L 73 20 10 20 6

FSBIH 7364R FSBIH 7364L 73 HSK25 6 20 4

FSBIH 7366R FSBIH 7366L 73 HSK25 6 20 6


DIA TRIMMING CUTTER art. FRB




low noisiness.

ART. nr Dimension

Prawe Lewe D d R < Z

FRB 7514R FRB 7514L 75 HSK 25R 1 * 4

FRB 76154R FRB 76154L 76 HSK 25R 1,5 * 4

FRB 7724R FRB 7724L 77 HSK 25R 2 * 4

FRB 78254R FRB 78254L 78 HSK 25R 2,5 * 4

FRB 7834R FRB 7834L 78 HSK 25R 3 * 4

FRB 80354R FRB 80354L 80 HSK 25R 3,5 * 4

FRB 8144R FRB 8144L 81 HSK 25R 4 * 4

FRB 82454R FRB 82454L 82 HSK 25R 4,5 * 4

FRB 8354R FRB 8354L 83 HSK 25R 5 * 4

FRB 7516R FRB 7516L 75 HSK 25R 1 * 6

FRB 76156R FRB 76156L 76 HSK 25R 1,5 * 6

FRB 7726R FRB 7726L 77 HSK 25R 2 * 6

FRB 78256R FRB 78256L 78 HSK 25R 2,5 * 6

FRB 7836R FRB 7836L 78 HSK 25R 3 * 6

FRB 80356R FRB 80356L 80 HSK 25R 3,5 * 6

FRB 8146R FRB 8146L 81 HSK 25R 4 * 6

FRB 82456R FRB 82456L 82 HSK 25R 4,5 * 6

FRB 8356R FRB 8356L 83 HSK 25R 5 * 6


DIA TRIMMING CUTTER art. FBM




low noisiness.

Prawe Lewe D d R1 R2 R3 ° Z

FBM 70164R FBM 70164L 70 16 3 2 1,5 20 4

FBM 70166R FBM 70166L 70 16 3 2 1,5 20 6

FBM 70204R FBM 70204L 70 20 3 2 1,5 20 4

FBM 70206R FBM 70206L 70 20 3 2 1,5 20 6

FBMH 8134R FBMH 8134L 81,1 HSK25 3 2 20 4

FBMH 8136R FBMH 8136L 81,1 HSK25 3 2 20 6

FBMH 81154R FBMH 81154L 81,1 HSK25 1,5 2 3 20 4

FBMH 81156R FBMH 81156L 81,1 HSK25 1,5 2 3 20 6

ART. nr Dimension


DIA HOGGER

Re-sharpening compact hogger in

diamond with cut positive angle,

height PCD 6 mm, suitable for wor-

king on chipboard panels, lamina-

ted,

M.D.F.,calcium silicate flooring, it

can be used on squaring machines

and squaring-edging machines.

Steel body with a high resistance.

DIA COMPAKT HOGGER „Positiv” or „Negativ”

DIA HOGGER „M-POWER”

DIA HOGGER „PROGRESIV”

DIA HOGGER „RADIUS”

DIA HOGGER WITH SAW BLADE

DOUBLE HOGGERS

HOGGER WITH SCORING SAW


DIA ADJUSTABLE GROOVING CUTTER WITH ADJUSTABLE CHANFERING KNIFE art. FRCS

Re-sharpening and adjustable grooving cutter in diamond with adjustable chan-

fering knife, suitable for grooving on chipboard panels,coated,

laminated, veneered, M.D.F., it can be used on edgebanding machines, excel-

lent finishing both in favour and against the working feed.

ART. Nr Dimension

Typ D d S Z

FRCS 124 120 30/35/40 4/7,5 6+6+3+3

FRCS 126 120 30/35/40 6/11,5 6+6+3+3

FRCS 164 160 30/35/40 4/7,5 8+8+4+4

FRCS 166 160 30/35/40 6/11,5 8+8+4+4

FRCS 184 180 30/35/40 4/7,5 10+10+5+5

FRCS 186 180 30/35/40 6/11,5 10+10+5+5


DIA ADJUSTABLE GROOVING CUTTER art. FRC

Re-sharpening and adjustable grooving cutter in diamond, height PCD 6 mm,

suitable for grooving on chipboard panels,coated, laminated,

veneered, M.D.F., it can be used on edgebanding machines.

ART. Nr Dimension

Typ D d S Z

FRC 124 120 30/35/40 4/7,5 8+8

FRC 126 120 30/35/40 6/11,5 8+8

FRC 164 160 30/35/40 4/7,5 8+8

FRC 166 160 30/35/40 6/11,5 8+8

FRC 184 180 30/35/40 4/7,5 8+8

FRC 186 180 30/35/40 6/11,5 8+8

FRC 204 200 30/35/40 4/7,5 12+12

FRC 206 200 30/35/40 6/11,5 12+12


CUTTERS FOR FOLDING art. FPF

Milling cutter in diamond suitable for working on folding with 90°, 95° and 100°

angles, it can be used on CNC machines for working

chipboard panels, coated in PVC and CTC.

ART. Nr Dimension

Typ D d S Z

FPF 12 120 30/35/40 4

FPF 15 150 30/35/40 4

FPF 16 160 30/35/40 4

FPF 18 180 30/35/40 4

FPF 20 200 30/35/40 4


DIA CUTTER FOR POSTFORMING - SOFTFORMING

The Post-forming process enables to fold the laminated plastic trimming

of M-D.F. panels on itself and either raw or surfaced

chipboard panels, already moulded.

The Softforming process enables to apply the edge/border to panels made of

M.D.F., raw or surfaced chipboard panels,

already moulded.

POSTFORMING

SOFTFORMING

ART. nr Dimension - wood-lord.comwood-lord.com/documents/cutting_tools/PCD tools.pdf · Nr Dimension Typ D d S Z FPF 12 120 30/35/40 4 FPF 15 150 30/35/40 4 FPF 16 160 30/35/40 4

Documents