This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Disassembly and Assembly 920 & 930 WHEEL LOADER POWER TRAIN
Transmission SMCS - 3150-16; 3150-15
Disassemble Transmission
start by:
a) separation of torque converter from transmission
34. Push the pins into shafts (40) with a punch and hammer.
35. Remove shafts (40), gears (39) and the washers from carrier assembly (36). There is a washer on each side of the gears. Remove the bearings from the gears. Remove the pins from the shafts.
36. Remove the dowel and sleeve (37) from carrier assembly (36) if a replacement is necessary.
37. Remove shaft assembly (42).
38. Remove pin (44) and seal rings (43) from the shaft assembly.
39. Remove the seal ring from coupling (41).
40. Remove the ring that holds coupling (41) in position and remove coupling (41) from shaft assembly (42).
41. Remove gear (45), disc assemblies (46) and plates (47) from the No. 2 clutch housing.
42. Remove No. 2 clutch housing (49) and remove piston (48) from the housing.
43. Remove the seal rings from piston (48).
Página 7 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE(S...
50. Install two 1/2"-13 NC forged eyebolts in clutch housing (55). Fasten a hoist and remove clutch housing (55) the pistons and the two planetary gear assemblies as a unit. Weight of the unit is 90 lb. (41 kg).
51. Remove tool (B) and remove the pistons from clutch housing (55).
52. Remove the seal rings from the pistons.
53. Remove bolt (59), the plate and the No. 3 carrier from clutch housing (55).
54. Turn clutch housing (55) over. Remove ring (63) that holds carrier (60) in position and remove No. 2 carrier (60) from the clutch housing.
55. Remove ring (61) and bearing (62) from clutch housing (55).
56. Remove seal rings (64) from each side of the clutch housing.
57. Remove the pins and the ring from the groove in No. 2 carrier (60).
58. Push pins (66) into shafts (65) with a punch and hammer.
59. Remove shafts (65), gears (67) and the washers from carrier (60). There is a washer on each side of the
Página 9 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE(S...
gears. Remove the bearings from the gears. Remove the pins from the shafts.
60. Remove seal ring (68) from No. 3 carrier (71).
61. Push pins (70) into shafts (69) with a punch and hammer.
62. Remove shafts (69), gears (72) and the washers from carrier (71). There is a washer on each side of the gears. Remove the bearings from the gears. Remove the pins from the shafts.
63. Remove springs (73) and pins (74).
64. Remove No. 4 disc assemblies (75) and the plates.
65. Remove ring (76) and remove gear (77).
Página 10 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE...
72. Remove bolts (87) and the washer and remove carrier (86).
73. Push pins (88) into the shafts with a punch and hammer.
74. Remove the shafts, the washers and gears (89) from carrier (86). There is a washer on each side of the gears. Remove the bearings from the gears. Remove the pins from the shafts.
75. Remove springs (90), pins (91), gear (93), disc assemblies (92) and the plates.
76. Remove bolts (94), the locks and retainer (95).
Página 12 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE...
2. Lower the temperature of bearing (4) and install it in No. 6 clutch housing (2).
3. Install ring (1) to hold bearing in position.
4. Install the pistons and seal rings in all of the clutch housings as follows:
a) Put clean oil on the seal rings.
b) Install seal rings (6) in the clutch housings.
c) Install seal rings (7) in pistons (5).
d) Make sure the seal rings are in the centers of their respective grooves. Lightly push the pistons into position in the housings.
5. Install two 3/8"-16 NC forged eyebolts in No. 6 clutch housing (2) and install the clutch housing and piston in the output transfer gear case.
NOTICEBe extra careful when the pistons are installed in the housings. Seal rings with damage or broken seal rings can be the result of too much force used or the pistons not in alignment with the housings.
Página 14 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE...
b) Put gears (17) in position in carrier (15) with washers (20) and (21) on each side of the gears.
c) Install shafts (18) in carrier (15) to hold gears (17) and the washers. Make sure the holes in the shafts are in alignment with the holes in the carrier.
d) Install pins (19) even with the surface of carrier (15) to hold shafts (18) in position.
11. Put No. 6 planet carrier (15) in position on the clutch housing. Make sure the springs and pins are in position and install the washers and bolts (24). Tighten the bolts to a torque of 85 ± 5 lb.ft. (115 ± 7 N·m).
12. Install sleeve (23), sun gear (22), the washer and bolt. Tighten the bolt to a torque of 34 ± 2 lb.ft. (45 ± 3 N·m).
13. Install plate (26) and No. 5 clutch ring gear (25).
14. Install long pins (28), the two disc assemblies (27) and plate (29). There must be a disc assembly on each side of plate (29).
Página 16 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE...
b) Install bearings (39) and (41) in each gear (40).
c) Put gears (40) in position in carrier (45) with washers (44) on each side of the gears.
d) Install each shaft (42) in carrier (45) to hold gears (40) and washers (44) in position. Make sure the holes in the shafts are in alignment with the holes in the carrier.
3) Install pins (43) even with the surface of carrier (45) to hold shafts (42) in position.
22. Assemble No. 3 planetary carrier as follows:
a) Install seal ring (46) on carrier (47).
b) Install bearings (48) and (50) in each gear (49).
Página 18 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE...
c) Put gears (49) in position in carrier (47) with washers (53) on each side of the gears.
d) Install each shaft (51) in carrier (47) to hold gears (49) and washers (53) in position. Make sure the holes in the shafts are in alignment with the holes in the carrier.
e) Install pins (52) even with the surface of carrier (47) to hold shafts (51) in position.
23. Lower the temperature of bearing (54). Install the bearing in No. 3 and 4 clutch housing (55) with the notch of the bearing down toward the No. 3 clutch side of housing (55).
24. Install ring (56) to hold bearing (54) in position.
25. Install No. 3 planetary carrier (47) in the No. 3 and 4 clutch housing. Make sure dowel (57) in the carrier is in alignment with notch (58) in the bearing.
26. Turn housing (55) and planetary carrier (47) over and install ring (59) to hold the planetary carrier in position.
Página 19 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE...
27. Install the No. 4 planetary carrier (45) in clutch housing (55).
28. Turn clutch housing (55) and the No. 4 planetary carrier over and install the plate and bolt (61) to hold the carrier in position. Make sure the boss in the plate is engaged with the hole in the No. 4 planetary carrier. Tighten bolt (61) to a torque of 34 ± 2 lb.ft. (45 ± 3 N·m).
29. Install ring (60) in No. 3 carrier (47).
30. Install tooling (A) to hold the No. 4 piston in position in clutch housing (55).
31. Install two 1/2"-13 NC forged eyebolts in clutch housing (55) and fasten a hoist to it.
32. Put clutch housing (55) in position on the transmission. Make sure the springs are correctly engaged in the No. 4 piston.
33. Remove the eyebolts and tooling (A).
Página 20 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE...
a) Install the seal ring on carrier assembly (79).
b) Install bearings (80) and (82) in each gear (81).
c) Put gears (81) in position in carrier assembly (79) with washers (85) on each side of the gears.
d) Install shaft (83) in carrier assembly (79) to hold gears (81) and washers (85) in position. Make sure the holes in the shafts are in alignment with the holes in the carrier assembly.
e) Install pins (84) even with the surface of carrier assembly (79) to hold shafts (83) in position.
46. Lower the temperature of bearing (87) and install it in plate (89). Make sure the notch in bearing (87) is down when it is installed in the plate. Install ring (86) to hold the bearing.
47. Heat sleeve (88) in oil to a maximum temperature of 275°F (135°C) and install it on carrier assembly (79). Install the dowel in carrier assembly (79) above sleeve (88). Install the seal ring on sleeve (88).
48. Put plate (89) on carrier assembly (79). Make sure the notch in bearing (87) engages with the dowel in carrier assembly (79). Install the ring that holds plate (89) and carrier assembly (79) together.
Página 23 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE...
49. Install plate (89) on the No. 2 clutch housing.
50. Install springs (90), the washers and bolts (91). Make sure all springs are engaged correctly and tighten bolts (91) to a torque of 85 ± 5 lb.ft. (115 ± 7 N·m).
51. Check to make sure the pistons are free in their clutch housings as follows:
a) Put air (free of water) under a pressure of 100 to 150 psi (7.0 to 10.5 kg/cm2) or (690 to 1030 kPa) into the five oil passages with tool (B).
b) There must be .12 to .25 in. (3.0 to 6.4 mm) of travel for each piston.
c) If the pistons do not move the distance in Step 51 b put a small amount of oil in the five passages. Follow procedure in Step 51 a. If the pistons still do not move, the transmission must be disassembled and the pistons checked.
52. Install two 3/8"-16 NC forged eyebolts in case (92). Fasten a hoist to case (92). Make sure the O-ring seals are in position on the output transfer gear case and install case (92).
53. Install the nine long bolts and washers that hold case (92) in position and tighten them to a torque of 85 ± 5 lb.ft. (115 ± 7 N·m).
Página 24 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE...
f) Put clean oil on seal rings (101) and install them on manifold (100).
g) Make sure the seal rings (101) are in the centers of their respective grooves. Lightly push manifold (100) into coupling (96).
h) Install the washers, bolts (103) and springs (102).
j) Make sure the O-ring seal is in position in coupling (96) and install piston (104) on the coupling. Install the bolts and locks that hold the piston and coupling together.
55. Install two 3/8"-16 NC forged eyebolts in the No. 1 clutch and fasten a hoist to it.
56. Install the No. 1 clutch in the transmission as shown.
Página 26 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE...
57. Install ring (105) to hold the No. 1 clutch in position.
58. If necessary make a replacement of the four bearings (106) and two seals for the control lever shafts with tool group (C). Install the inner bearings until they are even with the inside surface of the case. Install the outer two bearings until they are even with the bottom of the seal counterbores. Put 7M7260 Liquid Gasket Material in the seal counterbore. Install the seals with the lip of the seals toward the inside as shown.
59. Install the O-ring seals on sleeve (107).
60. Install sleeve (107) so it is pushed all the way into the output transfer gear case for installation of the valve manifold.
61. Make sure the five O-ring seals (108) are in position on the transmission.
Página 27 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE...
62. Install manifold (109) and tighten the four bolts to a torque of 35 ± 3 lb.ft. (45 ± 4 N·m).
63. Push sleeve (107) up into manifold (109) and install the ring to hold the sleeve in position.
NOTE: See ASSEMBLE TRANSMISSION HYDRAULIC CONTROL VALVES to assemble the selector and pressure control valves.
64. Put selector valve (110) in position and install two 5/16"-18 NC guide bolts approximately 7 in. (17.8 cm) long to hold the valve in position.
65. Put levers (113) in position. Make sure that the levers are engaged with the valve spools and install levers (111) and (112) with the washers and shafts. Install the bolts that hold levers (113) to the shafts and tighten them to a torque of 35 ± 3 lb.ft. (45 ± 4 N·m).
NOTICEWhen selector valve (110) is installed the valve spools must be held in position because they are free to fall out and be damaged.
Página 28 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE...
66. Put plate (114) in position. Install sleeve (115) and the O-ring seals in plate (114). Install the cover and fitting for sleeve (115) on the case.
67. Install pressure control valve (116) and install four of the bolts that hold the valves in position. Remove the guide bolts and install the remainder of the bolts that hold the valve together. Tighten the twelve point 5/16"-18 NC bolts to a torque of 22 ± 3 lb.ft. (28 ± 4 N·m) and the 3/8"-16 NC bolts to a torque of 35 ± 3 lb.ft. (45 ± 4 N·m).
68. Install the gasket, cover (118) and the back-up alarm (119).
69. Install the O-ring seals on sleeves (117) and install the sleeves in the transmission.
end by:
a) connection of torque converter to transmission
Copyright 1993 - 2010 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees.
Sun Nov 28 19:20:51 CST 2010
Página 29 de 29930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE...