ARCAT€¦ · Web viewRockfon is a subsidiary of Denmark-based ROCKWOOL International A/S, the world's largest producer of stone wool products.For the past 25 years, the ROCKWOOL

SECTION 09 51 00SUSPENDED ACOUSTICAL CEILINGS

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2013 - 2015 ARCAT, Inc. - All rights reserved

1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Suspended acoustical ceilings including the following:1.1.1.1 Acoustical tiles (direct applied) and panels (suspended).1.1.1.2 Stone wool open plenum ceiling systems.1.1.1.3 Exposed tee metal grid ceiling system and perimeter trim.

1.2 RELATED SECTIONS

1.2.1 Section 07 21 16 - Blanket Insulation.

1.2.2 Section 07 90 00 - Joint Protection.

1.2.3 Section 08 31 16 - Access Panels and Frames.

1.2.4 Section 09 26 13 - Gypsum Veneer Plastering.

1.2.5 Section 09 21 16.23 - Gypsum Board Shaft Wall Assemblies.

1.2.6 Section 09 54 00 - Specialty Ceilings.

1.2.7 Section 09 54 36 - Suspended Decorative Grids.

1.2.8 Section 40 96 20 - Process Control Software Instrument Lists.

1.2.9 Section 28 31 00 - Fire Detection and Alarm.

1.2.10 Section 21 00 00 - Fire Suppression.

1.2.11 Section 23 37 23.16 - HVAC Gravity Louvered-Penthouse Ventilators.

1.2.12 Section 26 51 00 - Interior Lighting.

1.2.13 Section 27 51 16 - Public Address Systems.

1.3 REFERENCES

1.3.1 ASTM International (ASTM):1.3.1.1 ASTM A635 - Standard Specification for Steel.1.3.1.2 ASTM C367 - Standard Test Methods for Strength Properties of Prefabricated

Architectural Acoustical Tile or Lay-in Ceiling Panels.1.3.1.3 ASTM C635 - Standard Specification for the Manufacture, Performance, and

Testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings.

1.3.1.4 ASTM C636 - Standard Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-In Panels.

09 51 00-1

1.3.1.5 ASTM E84 - Surface Burning Characteristics.1.3.1.6 ASTM E119 - Fire Tests of Building Construction and Material.1.3.1.7 ASTM E580 - Standard Practice for Application of Ceiling Suspension Systems

for Acoustical Tile and Lay-in Panels in Areas Requiring Seismic Restraint.1.3.1.8 ASTM E1264 - Standard Classification for Acoustical Ceiling Products.

1.3.2 American Society of Civil Engineers (ASCE):1.3.2.1 ASCE 7 - Minimum Design Loads for Buildings and Other Structures.

1.3.3 Ceiling and Interior Systems Construction Association (CISCA):1.3.3.1 CISCA Handbook - Acoustical Ceilings: Use and Practice.1.3.3.2 ASCE 7 and CISCA - Recommendations for Direct Hung Acoustical Tile and

Lay-In Panel Ceilings - Seismic Zones 0-2.1.3.3.3 ASCE 7 and CISCA - Recommendations for Direct Hung Acoustical Suspension

Ceiling Assemblies - Seismic Zones 3-4.

1.3.4 US Green Building Council (USGBC):1.3.4.1 Leadership in Energy and Environmental Design (LEED) green building rating

system.

1.3.5 Underwriters Laboratory (UL):1.3.5.1 UL - Fire Resistance Directory.1.3.5.2 UL 723 - Standard for Test for Surface Burning Characteristics of Building

Materials.1.3.5.3 CAN/ULC S102 - Surface Burning Characteristics of Building Materials and

Assemblies.

1.3.6 Warnock Hersey (WH):1.3.6.1 WH - Certification Listings.

1.4 DESIGN / PERFORMANCE REQUIREMENTS

1.4.1 Suspension System: Rigidly secure acoustic ceiling system including integral mechanical and electrical components with maximum deflection of 1:360.

1.4.2 Fire-Test-Response Characteristics:1.4.2.1 Fire-Resistance Characteristics: Where indicated on the Drawings, provide

acoustical panel ceilings identical to those of assemblies tested for fire resistance per ASTM E 119 by UL or another testing and inspecting agency acceptable to authorities having jurisdiction.

1.4.2.1.1 Identify materials with appropriate markings of applicable testing and inspecting agency.

1.4.2.2 Surface-Burning Characteristics: Acoustical panels complying with ASTM E1264 for Class A, B, or C products specified, when tested per ASTM E84.

1.4.3 Seismic Standard: Verify requirements of authorities having jurisdiction as to which subparagraphs below to reference if any.1.4.3.1 Standard for Ceiling Suspension Systems Requiring Seismic Restraint: Comply

with ASTM E580.1.4.3.2 CISCA's Recommendations for Acoustical Ceilings: Comply with CISCA's

"Recommendations for Direct-Hung Acoustical Tile and Lay-in Panel Ceilings--Seismic Zones 0-2."

1.4.3.3 CISCA's Guidelines for Systems Requiring Seismic Restraint: Comply with CISCA's "Guidelines for Seismic Restraint of Direct-Hung Suspended Ceiling Assemblies--Seismic Zones 3 and 4."

1.4.3.4 IBC Section 1613, "Metal Suspension Systems for Acoustical Tile and for Lay-in Panel Ceilings."

09 51 00-2

1.4.3.5 ASCE 7, "Minimum Design Loads for Buildings and Other Structures": Section 9, "Earthquake Loads."

1.5 SUBMITTALS

1.5.1 Submit under provisions of Section 01 30 00 - Administrative Requirements.

1.5.2 Product Data: Manufacturer's data sheets on each product to be used, including:1.5.2.1 Preparation instructions and recommendations.1.5.2.2 Dimensions, load carrying capacity, and performance standards compliance.1.5.2.3 Storage and handling requirements and recommendations.1.5.2.4 Installation and maintenance instructions.

1.5.3 Shop Drawings: Reflected ceiling plan indicating ceiling layouts, dimensions and perimeter conditions, and ceiling schedule including panel and grid types to match codes used on the Drawings. Indicate grid layouts and related dimensioning, junctions with other work or ceiling finishes, interrelation of mechanical and electrical items related to system. Indicate method of suspension where interference exists.

1.5.4 LEED Submittals: Provide documentation of how the requirements of Credit will be met:1.5.4.1 List of proposed materials with recycled content. Indicate post-consumer

recycled content and pre-consumer recycled content for each product having recycled content.

1.5.4.2 Product data and certification letter indicating percentages by weight of post-consumer and pre-consumer recycled content for products having recycled content.

1.5.4.3 Submit GREENGUARD certification for VOC and formaldehyde emissions.

1.5.5 Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.

1.5.6 Verification Samples: For each finish product specified, two samples, actual size of acoustical units, and two samples minimum size 12 inches (300 mm) long of main tees and cross tees square, representing actual product, color, finish and patterns.

1.5.7 Manufacturer's Certificates: Certify products meet or exceed specified requirements.

1.5.8 Closeout Submittals: Provide manufacturer's maintenance instructions that include recommendations for periodic cleaning and maintenance of all components.

1.6 QUALITY ASSURANCE

1.6.1 Manufacturer Qualifications: Company specializing in manufacturing products specified in this section with minimum three years documented experience.

1.6.2 Manufacturer member in good standing of CISCA (Ceiling and Interior Systems Construction Association)

1.6.3 Installer Qualifications: Company specializing in performing Work of this section with minimum three years documented experience.

1.6.4 Provide seismic design of suspended ceiling under direct supervision of Professional Engineer experienced in design of this Work and licensed at Project location.

1.6.5 Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.1.6.5.1 Finish areas designated by Architect.1.6.5.2 Do not proceed with remaining work until workmanship, color, and sheen are

09 51 00-3

approved by Architect.1.6.5.3 Refinish mock-up area as required to produce acceptable work.

1.6.6 Pre-installation Conference: Conduct conference at Project site minimum one week before installation. Agenda shall include project conditions, coordination with work of other trades, and layout of items which penetrate ceilings.

1.7 DELIVERY, STORAGE, AND HANDLING

1.7.1 Deliver in unopened bundles and store in a dry place with adequate air circulation. Do not deliver material to building until wet conditions such as concrete, plaster, paint, and adhesives have been completed and cured.

1.7.2 Store products in manufacturer's unopened packaging until ready for installation.

1.7.3 Protect system components from excessive moisture in shipment, storage, and handling.

1.8 SEQUENCING

1.8.1 Sequence Work to ensure acoustic ceilings are not installed until building is enclosed, sufficient heat is provided, dust generating activities and wet work have terminated, and overhead work is completed, tested, and approved.

1.8.2 Install acoustic units after interior wet work is dry.

1.8.3 Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.

1.9 PROJECT CONDITIONS

1.9.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.10 WARRANTY

1.10.1 Warranty: Provide manufacturer's standard warranty against manufacturing defects in material or workmanship when installed in accordance with the current CISCA Handbook and ASTM C367.1.10.1.1 Warranty Period: 30 years.

1.11 EXTRA MATERIALS

1.11.1 See Section 01 60 00 - Product Requirements.

1.11.2 Deliver extra acoustical units for Owner's use in maintenance. Label and store where directed by the Owner including codes used on the Drawings. Do not deliver to the Project site until the Owner is prepared to receive and store maintenance materials.1.11.2.1 Tile: Furnish 5 percent of total acoustic unit area of extra tile to Owner.1.11.2.2 Panels: Furnish 5 percent of total acoustic unit area of extra panels to Owner.1.11.2.3 Suspension System Components: Furnish 5 percent of each exposed

component of the quantity installed.

2 PRODUCTS

2.1 MANUFACTURERS

2.1.1 Acceptable Manufacturer: Rockfon, which is located at: 4849 S. Austin Ave.; Chicago, IL

09 51 00-4

60638; Toll Free Tel: 800-323-7164; Tel: 708-563-4600; Fax: 800-222-3744; Email:request info ([email protected]); Web:http://www.rockfon.com

2.1.2 Substitutions: Not permitted.

2.1.3 Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2 ACOUSTICAL TILES AND PANELS

2.2.1 Design White Acoustic Ceilings: Provide Rockfon Sonar stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.1.1 ASTM E1264 Classification: Type XX, Pattern E.2.2.1.2 Color: White.2.2.1.3 Texture: Lightly textured.2.2.1.4 Edges: Square Lay In (SQ).2.2.1.5 Edges: Square Tegular Narrow (SLN).2.2.1.6 Edges: Angled Tegular (SLT).2.2.1.7 Edges: Direct Mount (DMT).2.2.1.8 Edges: Shiplap (SLP).2.2.1.9 Edges: Semi-Concealed (SCD).2.2.1.10 Edges: Concealed X (CDX).2.2.1.11 Size: 24 by 24 inch (609 by 609 mm).2.2.1.12 Size: 24 by 48 inch (609 by 1219 mm).2.2.1.13 Size: 24 by 60 inch (609 by 1524 mm).2.2.1.14 Size: 24 by 72 inch (609 by 1828 mm).2.2.1.15 Size: 24 by 96 inch (609 by 2438 mm).2.2.1.16 Size: 30 by 30 inch (762 by 762 mm).2.2.1.17 Size: 20 by 60 inch (508 by 1524 mm).2.2.1.18 Size: 48 by 48 inch (1219 by 1219 mm).2.2.1.19 Thickness: 3/4 inch (19 mm).2.2.1.20 Thickness: 7/8 inch (22 mm).2.2.1.21 Thickness: 1 inch (25 mm).2.2.1.22 Lbs/Sq.ft: 0.69-0.842.2.1.23 Noise Reduction Coefficient (NRC): 0.90 to 0.95.2.2.1.24 Ceiling Attenuation Class (CAC): 22-25.2.2.1.25 Articulation Class (AC): 190.2.2.1.26 Fire Class: Class A.2.2.1.27 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0/0.2.2.1.28 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 10/5.2.2.1.29 Light Reflectance (LR): 0.85.2.2.1.30 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F

to 104 degrees F.2.2.1.31 Recycled Content: Up to 38 percent.2.2.1.32 R Value (BTU Units): 2.6 to 3.5.2.2.1.33 RSI Value (Watts Units): 0.46 to 0.62.2.2.1.34 VOC: GreenGuard Gold

2.2.2 Design White Acoustic Ceilings: Provide Rockfon Sonar Activity, stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.2.1 ASTM E1264 Classification: Type XX, Pattern E.2.2.2.2 Color: White.2.2.2.3 Texture: Lightly textured.2.2.2.4 Edges: Square Lay In (SQ).2.2.2.5 Edges: Square Tegular Narrow (SLN).2.2.2.6 Edges: Direct Mount (DMT).2.2.2.7 Size: 24 by 24 inch (609 by 609 mm).

09 51 00-5

2.2.2.8 Thickness: 1-1/2 inch (38 mm).2.2.2.9 Lbs./Sq.ft: 1.302.2.2.10 Noise Reduction Coefficient (NRC): 0.90.2.2.2.11 Ceiling Attenuation Class (CAC): 22.2.2.2.12 Articulation Class (AC): 180.2.2.2.13 Fire Class: Class A.2.2.2.14 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0/0.2.2.2.15 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 10/5.2.2.2.16 Light Reflectance (LR): 0.85.2.2.2.17 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F

to 104 degrees F.2.2.2.18 Recycled Content: Up to 40 percent.2.2.2.19 R Value (BTU Units): 5.3.2.2.2.20 RSI Value (Watts Units): 0.92.2.2.2.21 VOC: GreenGuard Gold

2.2.3 Design White Acoustic Ceilings: Provide Rockfon Sonar dB conforming to the following:2.2.3.1 ASTM E1264 Classification: Type XX, Pattern E.2.2.3.2 Color: White.2.2.3.3 Texture: Lightly textured.2.2.3.4 Edges: Square Lay In (SQ).2.2.3.5 Edges: Square Tegular Narrow (SLN).2.2.3.6 Edges: Angled Tegular (SLT).2.2.3.7 Size: 24 by 24 inch (609 by 609 mm).2.2.3.8 Thickness: 1 inch (25 mm).2.2.3.9 Lbs./Sq.ft: 0.692.2.3.10 Noise Reduction Coefficient (NRC): 0.85.2.2.3.11 Ceiling Attenuation Class (CAC): 33.2.2.3.12 Articulation Class (AC): 190.2.2.3.13 Fire Class: Class A.2.2.3.14 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 5/5.2.2.3.15 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 15/5.2.2.3.16 Light Reflectance (LR): 0.85.2.2.3.17 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F


2.2.4 Design White Acoustic Ceilings: Provide Rockfon Sonar dB, stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.4.1 ASTM E1264 Classification: Type XX, Pattern E.2.2.4.2 Color: White.2.2.4.3 Texture: Lightly textured.2.2.4.4 Edges: Square Lay In (SQ).2.2.4.5 Edges: Square Tegular Narrow (SLN).2.2.4.6 Edges: Angled Tegular (SLT).2.2.4.7 Edges: Shiplap (SLP).2.2.4.8 Size: 24 by 24 inch (609 by 609 mm).2.2.4.9 Thickness: 1-1/4 inch (32 mm).2.2.4.10 Lbs./Sq.ft: 0.992.2.4.11 Noise Reduction Coefficient (NRC): 0.85.2.2.4.12 Ceiling Attenuation Class (CAC): 35.2.2.4.13 Articulation Class (AC): 180.2.2.4.14 Fire Class: Class A.

09 51 00-6

2.2.4.15 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 5/5.2.2.4.16 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 15/5.2.2.4.17 Light Reflectance (LR): 0.85.2.2.4.18 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F


2.2.5 Design White Acoustic Ceilings: Provide Rockfon Sonar dB, stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.5.1 ASTM E1264 Classification: Type XX, Pattern E.2.2.5.2 Color: White.2.2.5.3 Texture: Lightly textured.2.2.5.4 Edges: Square Lay In (SQ).2.2.5.5 Edges: Square Tegular Narrow (SLN).2.2.5.6 Edges: Angled Tegular (SLT).2.2.5.7 Edges: Shiplap (SLP).2.2.5.8 Size: 24 by 24 inch (609 by 609 mm).2.2.5.9 Thickness: 1-1/2 inch (38 mm).2.2.5.10 Lbs./Sq.ft: 1.422.2.5.11 Noise Reduction Coefficient (NRC): 0.85.2.2.5.12 Ceiling Attenuation Class (CAC): 37.2.2.5.13 Articulation Class (AC): 170.2.2.5.14 Fire Class: Class A.2.2.5.15 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 5/5.2.2.5.16 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 15/5.2.2.5.17 Light Reflectance (LR): 0.85.2.2.5.18 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F


2.2.6 Design White Acoustic Ceilings: Provide Rockfon Sonar dB conforming to the following:2.2.6.1 ASTM E1264 Classification: Type XX, Pattern E.2.2.6.2 Color: White.2.2.6.3 Texture: Lightly textured.2.2.6.4 Edges: Square Lay In (SQ).2.2.6.5 Edges: Square Tegular Narrow (SLN).2.2.6.6 Edges: Angled Tegular (SLT).2.2.6.7 Edges: Shiplap (SLP).2.2.6.8 Size: 24 by 24 inch (609 by 609 mm).2.2.6.9 Thickness: 2 inch (50 mm).2.2.6.10 Lbs./Sq.ft: 1.612.2.6.11 Noise Reduction Coefficient (NRC): 0.85.2.2.6.12 Ceiling Attenuation Class (CAC): 43.2.2.6.13 Articulation Class (AC): 180.2.2.6.14 Fire Class: Class A.2.2.6.15 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0/0.2.2.6.16 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 10/5.2.2.6.17 Light Reflectance (LR): 0.85.2.2.6.18 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F

to 104 degrees F.

09 51 00-7

2.2.6.19 Recycled Content: Up to 40 percent.2.2.6.20 R Value (BTU Units): 7.0.2.2.6.21 RSI Value (Watts Units): 1.23.2.2.6.22 VOC: GreenGuard Gold

2.2.7 Design White Acoustic Ceilings: Provide Rockfon Alaska, stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.7.1 ASTM E1264 Classification: Type XX, Pattern G.2.2.7.2 Color: White.2.2.7.3 Texture: Smooth.2.2.7.4 Edges: Square Lay In (SQ).2.2.7.5 Edges: Square Tegular Narrow (SLN).2.2.7.6 Edges: Angled Tegular (SLT).2.2.7.7 Edges: Direct Mount (DMT).2.2.7.8 Edges: Shiplap (SLP).2.2.7.9 Edges: Semi-Concealed (SCD).2.2.7.10 Edges: Concealed X (CDX).2.2.7.11 Size: 24 by 24 inch (609 by 609 mm).2.2.7.12 Size: 24 by 48 inch (609 by 1219 mm).2.2.7.13 Thickness: 3/4 inch (19 mm).2.2.7.14 Thickness: 7/8 inch (22 mm).2.2.7.15 Lbs./Sq.ft: 0.69-0.752.2.7.16 Noise Reduction Coefficient (NRC): 0.90.2.2.7.17 Ceiling Attenuation Class (CAC): 22.2.2.7.18 Articulation Class (AC): 180.2.2.7.19 Fire Class: Class A.2.2.7.20 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0/5.2.2.7.21 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 5/0.2.2.7.22 Light Reflectance (LR): 0.86.2.2.7.23 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F

to 104 degrees F.2.2.7.24 Recycled Content: Up to 39 percent.2.2.7.25 R Value (BTU Units): 2.6.2.2.7.26 R Value (BTU Units): 3.1.2.2.7.27 RSI Value (Watts Units): 0.46.2.2.7.28 RSI Value (Watts Units): 0.54.2.2.7.29 VOC: GreenGuard Gold2.2.7.30 ASTM E1264 Classification: Type XX, Pattern G.2.2.7.31 Color: White.2.2.7.32 Texture: Smooth.2.2.7.33 Edges: Square Lay In (SQ).2.2.7.34 Edges: Square Tegular Narrow (SLN).2.2.7.35 Edges: Angled Tegular (SLT).2.2.7.36 Size: 24 by 24 inch (609 by 609 mm).2.2.7.37 Size: 24 by 48 inch (609 by 1219 mm).2.2.7.38 Thickness: 1 inch (25 mm).2.2.7.39 Lbs./Sq.ft: 0.692.2.7.40 Noise Reduction Coefficient (NRC): 0.85.2.2.7.41 Ceiling Attenuation Class (CAC): 35.2.2.7.42 Articulation Class (AC): 180.2.2.7.43 Fire Class: Class A.2.2.7.44 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 5/5.2.2.7.45 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 15/5.2.2.7.46 Light Reflectance (LR): 0.86.2.2.7.47 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F

to 104 degrees F.

09 51 00-8


2.2.8 Design Decoration Acoustic Ceilings: Provide Rockfon Color-all, stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.8.1 ASTM E1264 Classification: Type XX, Pattern G.2.2.8.2 Color: As selected by the Architect from manufacturer's full range.2.2.8.3 Color: As scheduled.2.2.8.4 Color: City Tones, Stone 701, Light Reflectance (LR) 55 percent.2.2.8.5 Color: City Tones, Plaster 702, Light Reflectance (LR) 58 percent.2.2.8.6 Color: City Tones, Gravel 703, Light Reflectance (LR) 34 percent.2.2.8.7 Color: City Tones, Mastic 704, Light Reflectance (LR) 33 percent.2.2.8.8 Color: City Tones, Zinc 705, Light Reflectance (LR) 33 percent.2.2.8.9 Color: City Tones, Concrete 706, Light Reflectance (LR) 16 percent.2.2.8.10 Color: City Tones, Tarmac 707, Light Reflectance (LR) 13 percent.2.2.8.11 Color: City Tones, Anthracite 708, Light Reflectance (LR) 7 percent.2.2.8.12 Color: City Tones, Black 08, Light Reflectance (LR) 4 percent.2.2.8.13 Color: Natural Tones, Stucco 720, Light Reflectance (LR) 70 percent.2.2.8.14 Color: Natural Tones, Chalk 721, Light Reflectance (LR) 51 percent.2.2.8.15 Color: Natural Tones, Linen 722, Light Reflectance (LR) 29 percent.2.2.8.16 Color: Natural Tones, Hemp 723, Light Reflectance (LR) 45 percent.2.2.8.17 Color: Natural Tones, Cork 724, Light Reflectance (LR) 30 percent.2.2.8.18 Color: Natural Tones, Earth 725, Light Reflectance (LR) 22 percent.2.2.8.19 Color: Natural Tones, Clay 726, Light Reflectance (LR) 22 percent.2.2.8.20 Color: Natural Tones, Hummus 727, Light Reflectance (LR) 5 percent.2.2.8.21 Color: Sensorial Tones, Light 740, Light Reflectance (LR) 71 percent.2.2.8.22 Color: Sensorial Tones, Sunrise 741, Light Reflectance (LR) 65 percent.2.2.8.23 Color: Sensorial Tones, Fresh 742, Light Reflectance (LR) 51 percent.2.2.8.24 Color: Sensorial Tones, Breeze 743, Light Reflectance (LR) 45 percent.2.2.8.25 Color: Sensorial Tones, Aqua 744, Light Reflectance (LR) 25 percent.2.2.8.26 Color: Sensorial Tones, Misty 745, Light Reflectance (LR) 60 percent.2.2.8.27 Color: Sensorial Tones, Twilight 746, Light Reflectance (LR) 29 percent.2.2.8.28 Color: Energetic Tones, Chili 750, Light Reflectance (LR) 12 percent.2.2.8.29 Color: Energetic Tones, Curacao 751, Light Reflectance (LR) 22 percent.2.2.8.30 Color: Energetic Tones, Vitamin 752, Light Reflectance (LR) 46 percent.2.2.8.31 Color: Precious Tones, Copper 760, Light Reflectance (LR) 34 percent.2.2.8.32 Color: Precious Tones, Gold 761, Light Reflectance (LR) 41 percent.2.2.8.33 Color: Precious Tones, Mercury 762, Light Reflectance (LR) 44 percent.2.2.8.34 Color: Sophisticated Tones, Garnet 770, Light Reflectance (LR) 12 percent.2.2.8.35 Color: Sophisticated Tones, Scarlet 771, Light Reflectance (LR) 8 percent.2.2.8.36 Color: Sophisticated Tones, Ermine 772, Light Reflectance (LR) 12 percent.2.2.8.37 Color: Sophisticated Tones, Emerald 773, Light Reflectance (LR) 7 percent.2.2.8.38 Texture: Smooth.2.2.8.39 Edges: Square Lay In (SQ).2.2.8.40 Edges: Square Tegular (SL).2.2.8.41 Edges: Concealed X (CDX).2.2.8.42 Size: 24 by 24 inch (609 by 609 mm).2.2.8.43 Thickness: 5/8 inch (16 mm).2.2.8.44 Thickness: 3/4 inch (19 mm).2.2.8.45 Thickness: 7/8 inch (22 mm).2.2.8.46 Lbs./Sq.ft: 0.47-0.752.2.8.47 Noise Reduction Coefficient (NRC): 085 to 0.95.2.2.8.48 Ceiling Attenuation Class (CAC): 22.2.2.8.49 Fire Class: Class A.

09 51 00-9

2.2.8.50 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 5/0.2.2.8.51 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 15/5.2.2.8.52 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F

to 104 degrees F.2.2.8.53 Recycled Content: Up to 40 percent.2.2.8.54 R Value (BTU Units): 2.2.2.2.8.55 R Value (BTU Units): 2.6.2.2.8.56 R Value (BTU Units): 3.1.2.2.8.57 RSI Value (Watts Units): 0.39.2.2.8.58 RSI Value (Watts Units): 0.46.2.2.8.59 RSI Value (Watts Units): 0.54.2.2.8.60 VOC: GreenGuard Gold

2.2.9 Basic White Acoustic Ceilings: Provide Rockfon Pacific, stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.9.1 ASTM E1264 Classification: Type XX, Pattern G.2.2.9.2 Color: White.2.2.9.3 Texture: Smooth.2.2.9.4 Edges: Square Lay In (SQ).2.2.9.5 Size: 24 by 24 inch (609 by 609 mm).2.2.9.6 Size: 24 by 48 inch (609 by 1219 mm).2.2.9.7 Thickness: 1/2 inch (12.5 mm).2.2.9.8 Lbs./Sq.ft: 0.332.2.9.9 Noise Reduction Coefficient (NRC): 0.60.2.2.9.10 Ceiling Attenuation Class (CAC): 0.2.2.9.11 Fire Class: Class A.2.2.9.12 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0/5.2.2.9.13 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 5/0.2.2.9.14 Light Reflectance (LR): 0.85.2.2.9.15 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F

to 104 degrees F.2.2.9.16 Recycled Content: Up to 37 percent.2.2.9.17 R Value (BTU Units): 1.8.2.2.9.18 RSI Value (Watts Units): 0.31.2.2.9.19 VOC: GreenGuard Gold2.2.9.20 ASTM E1264 Classification: Type XX, Pattern G.2.2.9.21 Color: White.2.2.9.22 Texture: Smooth.2.2.9.23 Edges: Square Lay In (SQ).2.2.9.24 Edges: Square Tegular (SL).2.2.9.25 Edges: Square Tegular Narrow (SLN).2.2.9.26 Size: 24 by 24 inch (609 by 609 mm).2.2.9.27 Size: 24 by 48 inch (609 by 1219 mm).2.2.9.28 Size: 24 by 60 inch (609 by 1524 mm).2.2.9.29 Size: 20 by 60 inch (508 by 1524 mm).2.2.9.30 Thickness: 5/8 inch (16 mm).2.2.9.31 Thickness: 3/4 inch (19 mm).2.2.9.32 Lbs./Sq.ft: 0.39-0.472.2.9.33 Noise Reduction Coefficient (NRC): 0.75.2.2.9.34 Ceiling Attenuation Class (CAC): 23.2.2.9.35 Fire Class: Class A.2.2.9.36 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0/5.2.2.9.37 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 5/0.2.2.9.38 Light Reflectance (LR): 0.85.2.2.9.39 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F

to 104 degrees F.

09 51 00-10

2.2.9.40 Recycled Content: Up to 37 percent.2.2.9.41 R Value (BTU Units): 2.2.2.2.9.42 R Value (BTU Units): 2.6.2.2.9.43 RSI Value (Watts Units): 0.39.2.2.9.44 RSI Value (Watts Units): 0.462.2.9.45 VOC: GreenGuard Gold

2.2.10 Basic White Acoustic Ceilings: Provide Rockfon Koral, stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.10.1 ASTM E1264 Classification: Type XX, Pattern E.2.2.10.2 Color: White.2.2.10.3 Texture: Lightly textured.2.2.10.4 Edges: Square Lay In (SQ).2.2.10.5 Edges: Square Tegular (SL).2.2.10.6 Edges: Square Tegular Narrow (SLN).2.2.10.7 Size: 24 by 24 inch (609 by 609 mm).2.2.10.8 Size: 24 by 48 inch (609 by 1219 mm).2.2.10.9 Thickness: 5/8 inch (16 mm).2.2.10.10 Lbs./Sq.ft: 0.39-0.472.2.10.11 Noise Reduction Coefficient (NRC): 0.85.2.2.10.12 Ceiling Attenuation Class (CAC): 22.2.2.10.13 Articulation Class (AC): 170.2.2.10.14 Fire Class: Class A.2.2.10.15 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0/5.2.2.10.16 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 5/0.2.2.10.17 Light Reflectance (LR): 0.86.2.2.10.18 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F


2.2.11 Basic White Acoustic Ceilings: Provide Rockfon Tropic stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.11.1 ASTM E1264 Classification: Type XX, Pattern G.2.2.11.2 Color: White.2.2.11.3 Texture: Smooth.2.2.11.4 Edges: Square Lay In (SQ).2.2.11.5 Edges: Square Tegular (SL).2.2.11.6 Edges: Square Tegular Narrow (SLN).2.2.11.7 Size: 24 by 24 inch (609 by 609 mm).2.2.11.8 Size: 24 by 48 inch (609 by 1219 mm).2.2.11.9 Size: 20 by 60 inch (508 by 1524 mm).2.2.11.10 Thickness: 5/8 inch (16 mm).2.2.11.11 Thickness: 3/4 inch (19 mm).2.2.11.12 Lbs./Sq.ft: 0.38-0.472.2.11.13 Noise Reduction Coefficient (NRC): 0.85.2.2.11.14 Noise Reduction Coefficient (NRC): 0.90.2.2.11.15 Ceiling Attenuation Class (CAC): 22.2.2.11.16 Articulation Class (AC): 180.2.2.11.17 Fire Class: Class A.2.2.11.18 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0/5.2.2.11.19 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 5/0.2.2.11.20 Light Reflectance (LR): 0.86.2.2.11.21 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F

09 51 00-11

to 104 degrees F.2.2.11.22 Recycled Content: Up to 36 percent.2.2.11.23 R Value (BTU Units): 2.2.2.2.11.24 R Value (BTU Units): 2.6.2.2.11.25 RSI Value (Watts Units): 0.39.2.2.11.26 RSI Value (Watts Units): 0.46.2.2.11.27 VOC: GreenGuard Gold

2.2.12 Commercial Acoustic Ceilings: Provide Rockfon Cinema Black, stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.12.1 ASTM E1264 Classification: Type XX, Pattern G.2.2.12.2 Color: Matte black.2.2.12.3 Texture: Lightly textured.2.2.12.4 Edges: Square Lay In (SQ).2.2.12.5 Size: 24 by 24 inch (609 by 609 mm).2.2.12.6 Size: 24 by 48 inch (609 by 1219 mm).2.2.12.7 Thickness: 5/8 inch (16 mm).Thickness: 1 inch (25 mm).2.2.12.8 Lbs./Sq.ft: 0.38-0.452.2.12.9 Noise Reduction Coefficient (NRC): 0.85.2.2.12.10 Fire Class: Class A.2.2.12.11 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 5/0.2.2.12.12 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 15/5.2.2.12.13 Light Reflectance (LR): 0.04.2.2.12.14 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F


2.2.13 Special Hygiene Area Acoustic Ceilings: Provide Rockfon Hygienic Plus stone wool (mineral wool) factory painted glass scrim ceilings, rear side covered with black fleece, with sealed edges conforming to the following:2.2.13.1 ASTM E1264 Classification: Type XX, Pattern E.2.2.13.2 Clean Room Classification: ISO14644, Class 5, low particle emission.2.2.13.3 Bacteriological Class: B1 (NF S 90-351, best class). Does not contribute to the

growth of Methicillin Resistant Staphylococcus Aureus (MRSA), bacteria resistant against antibiotics, candida albicans, and aspergillus niger mold responsible for pneumonias.

2.2.13.4 Enhanced, highly water repellant surface can be disinfected by steam cleaning, vacuum cleaned and resists diluted solution of ammonia, chlorine, quaternary ammonium and hydrogen peroxide.

2.2.13.5 Color: White.2.2.13.6 Texture: Lightly textured.2.2.13.7 Edges: Square Lay In (SQ).2.2.13.8 Size: 24 by 24 inch (609 by 609 mm).2.2.13.9 Size: 24 by 48 inch (609 by 1219 mm).2.2.13.10 Thickness: 3/4 inch (19 mm).2.2.13.11 Lbs./Sq.ft: 0.452.2.13.12 Noise Reduction Coefficient (NRC): 0.90.2.2.13.13 Ceiling Attenuation Class (CAC): 22.2.2.13.14 Fire Class: Class A.2.2.13.15 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0/5.2.2.13.16 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 5/0.

09 51 00-12

2.2.13.17 Light Reflectance (LR): 0.83.2.2.13.18 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F


2.2.14 Special Medical Area Acoustic Ceilings: Provide Rockfon Medical Standard stone wool (mineral wool) factory painted glass scrim ceilings, rear side covered with back fleece, with sealed edges conforming to the following:2.2.14.1 ASTM E1264 Classification: Type XX, Pattern E.2.2.14.2 Clean Room Classification: ISO14644, Class 5, low particle emission.2.2.14.3 Bacteriological Class: B5 and B10 (NF S 90-351, best class). Does not

contribute to the growth of Methicillin Resistant Staphylococcus Aureus (MRSA), bacteria resistant against antibiotics, candida albicans, and aspergillus niger mold responsible for pneumonias.

2.2.14.4 Can be vacuum cleaned and damp cloth or sponge cleaned in accordance with the manufacturer's instructions.

2.2.14.5 Color: White.2.2.14.6 Texture: Lightly textured.2.2.14.7 Edges: Square Lay In (SQ).2.2.14.8 Edges: Square Tegular (SL).2.2.14.9 Edges: Square Tegular Narrow (SLN).2.2.14.10 Size: 24 by 24 inch (609 by 609 mm).2.2.14.11 Size: 24 by 48 inch (609 by 1219 mm).2.2.14.12 Thickness: 5/8 inch (16 mm).2.2.14.13 Lbs./Sq.ft: 0.38-0.472.2.14.14 Noise Reduction Coefficient (NRC): 0.90.2.2.14.15 Ceiling Attenuation Class (CAC): 22.2.2.14.16 Articulation Class (CAC): 170.2.2.14.17 Fire Class: Class A.2.2.14.18 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0/0.2.2.14.19 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 10/5.2.2.14.20 Light Reflectance (LR): 0.86.2.2.14.21 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F


2.2.15 Special Medical Area Acoustic Ceilings: Provide Rockfon Medical Plus stone wool (mineral wool) factory painted glass scrim ceilings, rear side covered with back fleece, with sealed edges conforming to the following:2.2.15.1 ASTM E1264 Classification: Type XX, Pattern E.2.2.15.2 Clean Room Classification: ISO14644, Class 4.2.2.15.3 Bacteriological Class: B1 (NF S 90-351, best class). Does not contribute to the

growth of Methicillin Resistant Staphylococcus Aureus (MRSA), bacteria resistant against antibiotics, candida albicans, and aspergillus niger mold responsible for pneumonias.

2.2.15.4 Enhanced, highly water repellant surface can be disinfected by steam cleaning, vacuum cleaned and resists diluted solutions of ammonia, chlorine, quaternary ammonium and hydrogen peroxide.

2.2.15.5 Color: White.2.2.15.6 Texture: Lightly textured.

09 51 00-13

2.2.15.7 Edges: Square Lay In (SQ).2.2.15.8 Edges: Square Tegular (SL).2.2.15.9 Edges: Square Tegular Narrow (SLN).2.2.15.10 Edges: Concealed X (CDX).2.2.15.11 Size: 24 by 24 inch (609 by 609 mm).2.2.15.12 Size: 24 by 48 inch (609 by 1219 mm).2.2.15.13 Thickness: 3/4 inch (19 mm).2.2.15.14 Thickness: 7/8 inch (22 mm).2.2.15.15 Lbs./Sq.ft: 0.45-0.752.2.15.16 Noise Reduction Coefficient (NRC): 0.90.2.2.15.17 Ceiling Attenuation Class (CAC): 22.2.2.15.18 Fire Class: Class A.2.2.15.19 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0/5.2.2.15.20 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 5/0.2.2.15.21 Light Reflectance (LR): 0.83.2.2.15.22 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F


2.2.16 Special Medical Area Acoustic Ceilings: Provide Rockfon Medical Air stone wool (mineral wool) factory painted glass scrim ceilings, rear side covered with air tight high performance membrane, with sealed edges and conforming to the following:2.2.16.1 ASTM E1264 Classification: Type XX, Pattern E.2.2.16.2 Clean Room Classification: ISO14644, Class 3.2.2.16.3 Can be used in areas where differential pressure is required, successfully tested

under a pressure range of 5 to 40 Pa to achieve an air leakage of less than 0.5 m3/h/m2/Pa. Install with manufacturer's recommended closed cell neoprene foam tape where required to meet air pressure requirements.

2.2.16.4 Bacteriological Class: B1 and B5 (NF S 90-351). Does not contribute to the growth of Methicillin Resistant Staphylococcus Aureus (MRSA), bacteria resistant against antibiotics, candida albicans, and aspergillus niger mold responsible for pneumonias, and microorganisms such as eschericia coli, stachybotrys chartarum, staphylococcus aureaus, penicillium brevicumpactum, alternaria tenuissima, sporobolomyces roseum, and rhodotorula rubra.

2.2.16.5 Enhanced, highly water repellant surface can be disinfected by steam cleaning, vacuum cleaned and resists diluted solution of ammonia, chlorine, quaternary ammonium and hydrogen peroxide in accordance with the manufacturer's instructions.

2.2.16.6 Color: White.2.2.16.7 Texture: Lightly textured.2.2.16.8 Edges: Square Lay In (SQ).2.2.16.9 Size: 24 by 24 inch (609 by 609 mm).2.2.16.10 Size: 24 by 48 inch (609 by 1219 mm).2.2.16.11 Thickness: 1 inch (25 mm).2.2.16.12 Lbs./Sq.ft: 0.542.2.16.13 Noise Reduction Coefficient (NRC): 0.85.2.2.16.14 Ceiling Attenuation Class (CAC): 22.2.2.16.15 Fire Class: Class A.2.2.16.16 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 5/5.2.2.16.17 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 15/5.2.2.16.18 Light Reflectance (LR): 0.83.

09 51 00-14

2.2.16.19 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F to 104 degrees F.


2.2.17 Special Impact Area Acoustic Ceilings: Provide Rockfon Impact stone wool (mineral wool) reinforced factory painted glass scrim ceilings conforming to the following:2.2.17.1 ASTM E1264 Classification: Type XX, Pattern E.2.2.17.2 Tested for incidental and occasional ball impact.2.2.17.3 Color: White.2.2.17.4 Texture: Lightly textured.2.2.17.5 Edges: Square Lay In (SQ).2.2.17.6 Size: 24 by 24 inch (609 by 609 mm).2.2.17.7 Thickness: 3/4 inch (19 mm).2.2.17.8 Thickness: 1-1/2 inch (38 mm).2.2.17.9 Lbs./Sq.ft: 0.45-0.822.2.17.10 Noise Reduction Coefficient (NRC): 0.85.2.2.17.11 Ceiling Attenuation Class (CAC): 22.2.2.17.12 Fire Class: Class A.2.2.17.13 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0/5.2.2.17.14 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 5/0.2.2.17.15 Light Reflectance (LR): 0.86.2.2.17.16 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F


2.2.18 Special Industrial Area Acoustic Ceilings: Provide Rockfon Facett stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.18.1 ASTM E1264 Classification: Type XX, Pattern E.2.2.18.2 Tested for incidental and occasional ball impact.2.2.18.3 Color: Grey.2.2.18.4 Texture: Lightly textured.2.2.18.5 Edges: Square Lay In (SQ).2.2.18.6 Size: 24 by 48 inch (609 by 1218 mm).2.2.18.7 Thickness: 1-1/2 inch (38 mm).2.2.18.8 Thickness: 4 inch (101 mm).2.2.18.9 Lbs./Sq.ft: 0.82-1.932.2.18.10 Noise Reduction Coefficient (NRC): 1.00.2.2.18.11 Ceiling Attenuation Class (CAC): 22.2.2.18.12 Fire Class: Class A.2.2.18.13 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0/5.2.2.18.14 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 5/0.2.2.18.15 Light Reflectance (LR): 0.68.2.2.18.16 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F

to 104 degrees F.2.2.18.17 Recycled Content: Up to 42 percent.2.2.18.18 R Value (BTU Units): 5.3.2.2.18.19 R Value (BTU Units): 14.0.2.2.18.20 RSI Value (Watts Units): 0.92.

09 51 00-15

2.2.18.21 RSI Value (Watts Units): 2.47.2.2.18.22 VOC: GreenGuard Gold

2.2.19 Special Industrial Area Acoustic Ceilings: Provide Rockfon Industrial Opal stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.19.1 ASTM E1264 Classification: Type XX, Pattern G.2.2.19.2 Tested for incidental and occasional ball impact.2.2.19.3 Color: Opal.2.2.19.4 Texture: Smooth.2.2.19.5 Edges: Square Lay In (SQ).2.2.19.6 Size: 24 by 48 inch (609 by 1218 mm).2.2.19.7 Thickness: 2 inch (50 mm).2.2.19.8 Lbs./Sq.ft: 0.802.2.19.9 Noise Reduction Coefficient (NRC): 1.05.2.2.19.10 Ceiling Attenuation Class (CAC): 22.2.2.19.11 Fire Class: Class A.2.2.19.12 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0-5/0-

5.2.2.19.13 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 5-15 / 0-5.2.2.19.14 Light Reflectance (LR): 0.64.2.2.19.15 Sag Resistance: Dimensionally stable up to 100% relative humidity/32 degrees F


2.2.20 Special Industrial Area Acoustic Ceilings: Provide Rockfon Industrial Nature stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.20.1 ASTM E1264 Classification: Type XX, Pattern G.2.2.20.2 Tested for incidental and occasional ball impact.2.2.20.3 Color: Nature.2.2.20.4 Texture: Smooth.2.2.20.5 Edges: Square Lay In (SQ).2.2.20.6 Size: 24 by 48 inch (609 by 1218 mm).2.2.20.7 Thickness: 2 inch (50 mm).2.2.20.8 Lbs./Sq.ft: 0.802.2.20.9 Noise Reduction Coefficient (NRC): 1.05.2.2.20.10 Ceiling Attenuation Class (CAC): 22.2.2.20.11 Fire Class: Class A.2.2.20.12 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0-5/0-



2.2.21 Special Industrial Area Acoustic Ceilings: Provide Rockfon Industrial Black stone wool (mineral wool) factory painted glass scrim ceilings conforming to the following:2.2.21.1 ASTM E1264 Classification: Type XX, Pattern G.2.2.21.2 Tested for incidental and occasional ball impact.2.2.21.3 Color: Black.

09 51 00-16

2.2.21.4 Texture: Smooth.2.2.21.5 Edges: Square Lay In (SQ).2.2.21.6 Size: 24 by 48 inch (609 by 1218 mm).2.2.21.7 Thickness: 2 inch (50 mm).2.2.21.8 Lbs./Sq.ft: 0.802.2.21.9 Noise Reduction Coefficient (NRC): 1.05.2.2.21.10 Ceiling Attenuation Class (CAC): 22.2.2.21.11 Fire Class: Class A.2.2.21.12 Fire Performance UL 723 (ASTM E84) Flame Spread / Smoke Developed: 0-5/0-


to 104 degrees F.2.2.21.16 Recycled Content: Up to 42 percent.2.2.21.17 R Value (BTU Units): 7.0.2.2.21.18 RSI Value (Watts Units): 1.23.

2.3 OPEN PLENUM CEILING SYSTEMS

2.3.1 Rockfon Contour Open Plenum Ceiling System.2.3.1.1 Baffle Panels:

2.3.1.1.1 Size: 1 foot 11-5/8 inch by 3 foot 11-1/4 inch.2.3.1.1.2 Fire Class: A.2.3.1.1.3 Fire Performance UL 723 (ASTM E 84) Flame Spread / Smoke Developed:

0/5.2.3.1.1.4 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 5/0.2.3.1.1.5 Acoustical Performance: In accordance with manufacturers current

published information based on unit types and Hz measurement.2.3.1.1.6 Light Reflection: 0.79.2.3.1.1.7 Recycled Content: Up to 39 percent.

2.3.2 Rockfon Multiflex Fibral Baffle Open Plenum Ceiling System.2.3.2.1 Baffle Panels:

2.3.2.1.1 Size: 12 inch by 3 foot 11-1/4 inch.2.3.2.1.2 Size: 1 foot 5-3/8 inch by 3 foot 11-1/4 inch.2.3.2.1.3 Size: 1 foot 11-5/8 inch by 3 foot 11-1/4 inch.2.3.2.1.4 Fire Class: A.2.3.2.1.5 Fire Performance UL 723 (ASTM E 84) Flame Spread / Smoke Developed:



2.3.2.2 Frame:2.3.2.2.1 Three-sided white frame.

2.3.3 Rockfon Multiflex Opal Baffle Open Plenum Ceiling System.2.3.3.1 Baffle Panels: Stone wool (mineral wool) framed baffles.

2.3.3.1.1 Size: 12 inch by 3 foot 11-1/4 inch.2.3.3.1.2 Size: 1 foot 5-3/8 inch by 3 foot 11-1/4 inch.2.3.3.1.3 Size: 1 foot 11-5/8 inch by 3 foot 11-1/4 inch.2.3.3.1.4 Fire Class: A.2.3.3.1.5 Fire Performance UL 723 (ASTM E 84) Flame Spread / Smoke Developed:

0/5.

09 51 00-17

2.3.3.1.6 Fire Performance CAN ULC S102 Flame Spread / Smoke Developed: 5/0.2.3.3.1.7 Acoustical Performance: In accordance with manufacturers current


2.3.3.2 Frame:2.3.3.2.1 Two-sided galvanized frame.

2.3.4 Rockfon Island Open Plenum Ceiling System.2.3.4.1 Baffle Panels: Stone wool (mineral wool) baffles.

2.3.4.1.1 Size: 3 foot 9-11/16 inch by 3 foot 9-11/16 inch.2.3.4.1.2 Size: 3 foot 9-11/16 inch by 5 foot 9-5/16 inch.2.3.4.1.3 Size: 3 foot 9-11/16 inch by 7 foot 8-15/16 inch.2.3.4.1.4 Visible Side: Factory painted glass scrim.2.3.4.1.5 Rear Side: White acoustic fleece for light and heat reflection.2.3.4.1.6 Fire Class: A.2.3.4.1.7 Fire Performance UL 723 (ASTM E 84) Flame Spread / Smoke Developed:



2.4 SUSPENSION SYSTEM COMPONENTS - TYPICAL

2.4.1 Provide suspension system components from the same manufacturer as the acoustical ceiling components unless approved by the ceiling manufacturer in writing to comply with manufacturer's installation and warranty requirements.

2.4.2 Performance Standards: Suspension system manufacturer's standard direct-hung metal suspension system and attachment devices complying with project requirements and applicable building codes and regulations applicable at the location of the project.2.4.2.1 Suspension components shall comply with ASTM C635.

2.5 SUSPENSION SYSTEM COMPONENTS - GYSPSUM BOARD APPLICATIONS

2.5.1 1-3/8 inch (35 mm), Heavy-Duty, Double Web Drywall Suspension Grid:2.5.1.1 Non-fire Rated Grid: Chicago Metallic, 640 Hook Grid.2.5.1.2 Non-fire Rated Grid: Chicago Metallic, 660 Stab Grid.2.5.1.3 Fire Rated Grid: Chicago Metallic, 650 Hook Grid.2.5.1.4 Fire Rated Grid: Chicago Metallic, 670 Stab Grid.2.5.1.5 Furring Runners: 0.020 inch (0.5 mm) thick steel, 1-3/8 inch (35 mm) wide

knurled face by 1-1/2 inch (38 mm) high by 144 inch (3657 mm) long with factory punched cross tee slots, hanger holes, and non-directional bayonet end tab couplings.

2.5.1.6 Furring Tees: 0.020 inch (0.5 mm) thick steel, 1-3/8 inch (35 mm) wide, knurled face by 1-1/2 inch (38 mm) high by 48 inch (1219 mm) long with end tab couplings, factory punched cross tee slots, and hanger holes.

2.5.1.7 Furring Cross Channels: 0.020 inch (0.5 mm) thick steel, 1-3/8 inch (35 mm) wide knurled face by 7/8 inches high by 48 inches long with straight locking end tabs.

2.5.1.8 Cross Tees: 0.020 inch (0.5 mm) thick steel, steel, 15/16 inch (23.8 mm) wide by 1-1/2 inch (38 mm) high by 48 inch (1219 mm) long with stab-type end tab couplings, factory punched cross tee slots, and hanger holes. Coated with factory applied white baked-on enamel paint finish.

2.5.1.9 Wall Track: 0.020 inch (0.5 mm) thick steel, 1-9/16 inch (40 mm) high by 120

09 51 00-18

inch (3048 mm) long with 1 inch (25 mm) top and bottom flange.

2.5.2 Non-fire Rated Grid: Chicago Metallic, SpanFast.2.5.2.1 Furring Runners: 0.020 inch (0.5 mm) thick steel, 1-3/8 inch (35 mm) wide

knurled face by 1-1/2 inch (38 mm) high by longest practical length and factory punched hanger holes.

2.5.2.2 Wall Track: 0.020 inch (0.5 mm) thick steel, with 3/4 inch (19 mm) top flange by 1-9/16 inch (40 mm) high by 1 inch (25 mm) bottom flange by 120 inch (3048 mm) long.

2.5.3 Radius Drywall Ceiling Suspension:2.5.3.1 640CR Radius furring runner is made from corrosion resistant galvanized steel

and is flame spread Class A, pre-notched on 8 inch (203 mm) intervals to flex to large radius concave and convex ceiling designs.

2.5.3.2 Once the desired radius is reached, 435 furring runner clips are fastened to the runners to maintain the desired radius.

2.5.3.3 The 1-3/8 (35 mm) wide face is knurled for easy attachment of fasteners and factory punched for accurate cross member spacing.

2.6 SUSPENSION SYSTEM COMPONENTS - GENERAL APPLICATIONS

2.6.1 Tempra 9/16 inch (14.2 mm) Exposed Grid:2.6.1.1 Non-fire Rated Grid: Chicago Metallic, Tempra 4000.2.6.1.2 Fire Rated Grid: Chicago Metallic, Tempra 4050.2.6.1.3 Intermediate duty.2.6.1.4 Heavy duty.2.6.1.5 Main Tees:

2.6.1.5.1 Materials: Commercial quality galvanized steel 9/16 inch (14.2 mm) wide l by 1-1/2 or 1-5/8 inch (38 or 41.2 mm) high as recommended by the manufacturer based on application, by longest practical length with factory punched cross tee slots, hanger holes, miters, and integral couplings.

2.6.1.5.2 Capping: Steel with standard factory applied baked-on enamel paint.2.6.1.5.3 Capping: Aluminum with standard factory applied baked-on enamel paint.

2.6.1.6 Cross Tees:2.6.1.6.1 Materials: Commercial quality galvanized steel 9/16 inch (14.2 mm) wide

by 1-1/2 inch (38 mm) high by longest practical length, factory punched cross tee slots, hanger holes, and either snap-in or stab-in end tabs.

2.6.1.6.2 Finish and Reveal: Identical to main tees.

2.6.2 UltraLine 9/16 inch (14.2 mm) Exposed Grid with Reveal:2.6.2.1 Non-fire Rated Grid: Chicago Metallic, Ultraline 4500 with 1/4 inch (6.3 mm)

reveal.2.6.2.2 Fire Rated Grid: Chicago Metallic, Ultraline 4550 with 1/4 inch (6.3 mm) reveal.2.6.2.3 Fire Rated Grid: Chicago Metallic, Ultraline 4600 with 1/8 inch (3.1 mm) reveal.2.6.2.4 Intermediate duty.2.6.2.5 Heavy duty.2.6.2.6 Main Tees:

2.6.2.6.1 Materials: Commercial quality galvanized steel 9/16 inch (14.2 mm) wide with reveal by 1-3/4 inch (45 mm) high by longest practical length with factory punched cross tee slots/notches, hanger holes, miters, and integral couplings.


with reveal by 1-3/4 inch (45 mm) high by longest practical length by longest practical length, factory punched cross tee slots, hanger holes, miters and stake-on end clips.


09 51 00-19

2.6.3 15/16 inch (23.8 mm) Exposed Snap-Grid:2.6.3.1 Non-fire Rated Grid: Chicago Metallic, 200 Snap Grid.2.6.3.2 Fire Rated Grid: Chicago Metallic, 250 Fire Front Snap Grid.2.6.3.3 Intermediate duty.2.6.3.4 Heavy duty.2.6.3.5 Main Tees:

2.6.3.5.1 Materials: Commercial quality galvanized steel in thickness recommended by the manufacturer based on application, 15/16 inch (23.8 mm) wide by 1-1/2 inch (38 mm) high by longest practical length with factory punched cross tee slots, hanger holes, and integral bayonet-style end couplings.

2.6.3.5.2 Capping: Steel affixed to 15/16 inch (23.8 mm) wide flange.2.6.3.5.3 Capping: Aluminum affixed to 15/16 inch (23.8 mm) wide flange.

2.6.3.6 Cross Tees:2.6.3.6.1 Materials: Commercial quality galvanized steel in thickness recommended

by the manufacturer based on application, 15/16 inch (23.8 mm) wide by 1-3/4 inch (45 mm) high by longest practical length factory punched cross tee slots, hanger holes, and integral snap-grid end couplings.

2.6.3.6.2 Cap and Finish: Identical to main tees.2.6.3.7 Non-fire Rated Seismic Grid: Chicago Metallic, 1200 Stab Grid.2.6.3.8 Fire Rated Seismic Grid: Chicago Metallic, 1250 Stab Grid.

2.6.4 15/16 inch (23.8 mm) Exposed Seismic-Grid:2.6.4.1 Intermediate duty.2.6.4.2 Heavy duty.2.6.4.3 Main Tees:

2.6.4.3.1 Materials: Commercial quality galvanized steel in thickness recommended by the manufacturer based on application, 15/16 inch (23.8 mm) wide by 1-1/2 inch (38 mm) high by longest practical length with factory punched cross tee slots, hanger holes, and integral bayonet-style end couplings.

2.6.4.3.2 Capping: Steel affixed to 15/16 inch (23.8 mm) wide flange.2.6.4.4 Cross Tees:

2.6.4.4.1 Materials: Commercial quality galvanized steel in thickness recommended by the manufacturer based on application, 15/16 inch (23.8 mm) wide by 1-1/2 or 1-5/16 inch (33 or 38 mm) high as recommended by the manufacturer based on application, by longest practical length factory punched cross tee slots and hanger holes.

2.6.4.4.2 Cap and Finish: Identical to main tees.

2.6.5 Tempra 15/16 inch (23.8 mm) Exposed Grid:2.6.5.1 Non-fire Rated Grid: Chicago Metallic, Tempra 4000.2.6.5.2 Fire Rated Grid: Chicago Metallic, Tempra 4050.2.6.5.3 Intermediate duty.2.6.5.4 Heavy duty.2.6.5.5 Main Tees:

2.6.5.5.1 Materials: Commercial quality galvanized steel 15/16 inch (23.8 mm) wide with reveal by 1-1/2 or 1-5/8 inch (38 or 41.2 mm) high as recommended by the manufacturer based on application, by longest practical length with factory punched cross tee slots, hanger holes, miters, and integral couplings.



with reveal by 1-1/2 inch (38 mm) high by longest practical length, factory punched cross tee slots, hanger holes, and either snap-in or stab-in end tabs.

09 51 00-20


2.6.6 UltraLine 15/16 inch (23.8 mm) Exposed Grid with Reveal:2.6.6.1 Non-fire Rated Grid: Chicago Metallic, Ultraline 4500 with 1/4 inch (6.3 mm)

reveal.2.6.6.2 Fire Rated Grid: Chicago Metallic, Ultraline 4550 with 1/4 inch (6.3 mm) reveal.2.6.6.3 Fire Rated Grid: Chicago Metallic, Ultraline 4600 with 1/8 inch (3.1 mm) reveal.2.6.6.4 Intermediate duty.2.6.6.5 Heavy duty.2.6.6.6 Main Tees:



with reveal by 1-3/4 inch (45 mm) high by longest practical length by longest practical length, factory punched cross tee slots, hanger holes, miters and stake-on end clips.


2.7 SUSPENSION SYSTEM COMPONENTS - BOLT-SLOT APPLICATIONS

2.7.1 Tempra 9/16 inch (14.3 mm) Bolt Slot Suspension:2.7.1.1 Non-fire Rated Grid: Chicago Metallic, Tempra 4000.2.7.1.2 Fire Rated Grid: Chicago Metallic, Tempra 4050.2.7.1.3 Intermediate duty.2.7.1.4 Heavy duty.2.7.1.5 Main Tees:

2.7.1.5.1 Materials: Commercial quality galvanized steel 9/16 inch (14.3 mm) wide with reveal by 1-1/2 or 1-5/8 inch (38 or 41.2 mm) high as recommended by the manufacturer based on application, by longest practical length with factory punched cross tee slots, hanger holes, and integral couplings.



with reveal by 1-1/2 inch (38 mm) high by longest practical length, factory punched cross tee slots, hanger holes, and either snap-in or stab-in end tabs.


2.7.2 UltraLine 9/16 inch (14.3 mm) Bolt Slot Suspension with Reveal:2.7.2.1 Non-fire Rated Grid: Chicago Metallic, Ultraline 4500 with 1/4 inch reveal.2.7.2.2 Fire Rated Grid: Chicago Metallic, Ultraline 4550 with 1/4 inch reveal.2.7.2.3 Non-fire Rated Grid: Chicago Metallic, Ultraline 4600 with 1/8 inch reveal.2.7.2.4 Intermediate duty.2.7.2.5 Heavy duty.2.7.2.6 Main Tees:



with reveal by 1-3/4 inch (45 mm) high by longest practical length by

09 51 00-21

longest practical length, factory punched cross tee slots, hanger holes, miters and stake-on end clips.


2.8 SUSPENSION SYSTEM COMPONENTS - SPECIAL APPLICATIONS

2.8.1 1-3/8 inch (35 mm) Exposed Wide-Face Grid:2.8.1.1 Non-fire Rated Grid: Chicago Metallic, 660 Wide Face.2.8.1.2 Heavy Duty.2.8.1.3 Main Runners:

2.8.1.3.1 Materials: Hot Dipped Galvanized steel 1-3/8 inch (35 mm) wide by 1-1/2 inch high (38 mm) high by 144 inch (3657 mm) long with factory punched cross tee slots, hanger holes, and integral bayonet-style end couplings.

2.8.1.3.2 Capping: Steel affixed to flange in width recommended by the manufacturer.

2.8.1.3.3 Capping: Aluminum affixed to flange in width recommended by the manufacturer.

2.8.1.4 Cross Tees:2.8.1.4.1 Materials: Hot Dipped Galvanized steel 1-3/8 inch (35 mm) wide by 1-1/2

inch (38 mm) high by longest practical length with factory punched cross tee slots and hanger holes.

2.8.1.4.2 Capping: Identical to main runners.

2.8.2 1-3/8 inch (35 mm) Exposed Gasketed Grid:2.8.2.1 Non-fire Rated Grid: Chicago Metallic, BarrierGrid.2.8.2.2 Heavy Duty.2.8.2.3 Main Runners:

2.8.2.3.1 Materials: Hot Dipped Galvanized steel 1-3/8 inch (35 mm) wide by 1-1/2 inch high (38 mm) high by 144 inch (3657 mm) long with factory punched cross tee slots, hanger holes, and integral bayonet-style end couplings.

2.8.2.3.2 Capping: Aluminum affixed to 1-3/8 inch (35 mm) flange.2.8.2.4 Cross Tees:

2.8.2.4.1 Materials: Hot Dipped Galvanized steel 1-3/8 inch (35 mm) wide by 1-1/2 inch (38 mm) high by longest practical length with factory punched cross tee slots, hanger holes, and stab in couplings.

2.8.2.4.2 Capping: Identical to main runners.2.8.2.5 Gasket Materials:

2.8.2.5.1 Machine applied to edge of the tee. Gasket must have a 1/8 inch (3.175 mm) overhang on all cross tees.

2.8.2.5.2 Closed cell PVC foam resists UV oxidation, mildew and fungus, conformable to smooth and irregular surfaces, sealing against water, moisture, dirt and air-infiltration when compressed 30%.

2.8.2.5.3 Elastomeric construction adjust to thermal movement of structural elements without leaking and remain flexible.

2.8.2.5.4 Dimensionally stable and will not drip, ooze, or run when under compression. Gasket remains flexible at low temperatures, has excellent chemical resistance and forms an acoustic seal.

2.8.2.5.5 Average density of 8 lb./cu. ft. (128 kg./cu. m) and a compression deflection of 2 psi (13.7 kPa) per ASTM D1667.

2.8.3 Aluminum 15/16 inch (23.8 mm) Exposed Grid:2.8.3.1 Non-fire Rated Grid: Chicago Metallic, 260 Aluminum Cap.2.8.3.2 Fire Rated Grid: Chicago Metallic, 280 Aluminum Cap.2.8.3.3 Non-fire Rated Grid: Chicago Metallic, 1260 Aluminum Cap.2.8.3.4 Fire Rated Grid: Chicago Metallic, 1280 Aluminum Cap.2.8.3.5 Intermediate duty.

09 51 00-22

2.8.3.6 Heavy duty.2.8.3.7 Main Tees:

2.8.3.7.1 Materials: Commercial quality galvanized steel 15/16 inch (23.8 mm) wide by 1-1/2 inch (38 mm) high, by 144 inch (3657 mm) long with factory punched cross tee slots, hanger holes, and integral bayonet-style end couplings.

2.8.3.7.2 Capping: Aluminum affixed to 15/16 inch (23.8 mm) flange.2.8.3.8 Cross Tees:

2.8.3.8.1 Materials: Commercial quality galvanized steel 15/16 inch (23.8 mm) wide by 1-1/2 inch (38 mm) high by longest practical length, factory punched cross tee slots, hanger holes, and integral stab-in grid end coupling.

2.8.3.8.2 Cap: Identical to main tees.

2.8.4 Aluminum 15/16 inch (23.8 mm) Exposed Grid:2.8.4.1 Non-fire Rated Grid: Chicago Metallic, 830 All Aluminum Cap.2.8.4.2 Light duty.2.8.4.3 Main Tees:

2.8.4.3.1 Materials: Aluminum 15/16 inch (23.8 mm) wide by 1-1/2 inch (38 mm) high, by 144 inch (3657 mm) long with factory punched cross tee slots, hanger holes, and integral end couplings.

2.8.4.3.2 Capping: Aluminum affixed to 15/16 inch (23.8 mm) flange.2.8.4.4 Cross Tees:

2.8.4.4.1 Materials: Aluminum 15/16 inch (23.8 mm) wide by 1-1/2 inch (38 mm) high by longest practical length, factory punched cross tee slots, hanger holes, and integral stab-in grid end coupling.


2.8.5 HDG-60 Steel 15/16 inch (23.8 mm) Exposed Grid:2.8.5.1 Fire Rated Grid: Chicago Metallic, 1830 HDG-60 steel with aluminum cap.2.8.5.2 Intermediate Duty.2.8.5.3 Main Tees:

2.8.5.3.1 Materials: Commercial quality galvanized steel 15/16 inch (23.8 mm) wide by 1-1/2 inch (38 mm) high, by 144 inch (3657 mm) long with factory punched cross tee slots, hanger holes, and integral end couplings.

2.8.5.3.2 Capping: Aluminum affixed to 15/16 inch (23.8 mm) flange.2.8.5.3.3 Manufactured with fire expansion reliefs.


by 1-1/2 inch (38 mm) high by longest practical length, factory punched cross tee slots, hanger holes, and integral stab-in grid end coupling.


2.8.6 Stainless Steel 15/16 inch (23.8 mm) Exposed Grid:2.8.6.1 Non-fire Rated Grid: Chicago Metallic, 730 Stainless Steel.2.8.6.2 Intermediate Duty.2.8.6.3 Main Tees:

2.8.6.3.1 Materials: Type 304 stainless steel 15/16 inch (23.8 mm) wide by 1-1/2 inch (38 mm) high, by 144 inch (3657 mm) long with factory punched cross tee slots, hanger holes, and capped with base 304-2D Stainless Steel.

2.8.6.4 Cross Tees:2.8.6.4.1 Materials: Type 304 stainless steel 15/16 inch (23.8 mm) wide by 1-1/2

inch (38 mm) high by longest practical length, integral snap-grid end couplings, factory punched cross tee slots, and hanger hole.


2.8.7 15/16 inch (23.8 mm) Wide Face Exposed Grid:

09 51 00-23

2.8.7.1 Non-fire Rated Grid: Chicago Metallic, 660 Wide Face.2.8.7.2 Heavy Duty.2.8.7.3 Main Runners:

2.8.7.3.1 Materials: Hot Dipped Galvanized steel 15/16 inch (23.8 mm) wide by 1-1/2 inch high (38 mm) high by 144 inch (3657 mm) long with factory punched cross tee slots, hanger holes, and integral bayonet-style end couplings.

2.8.7.3.2 Capping: Steel affixed to flange in width recommended by the manufacturer.

2.8.7.3.3 Capping: Aluminum affixed to flange in width recommended by the manufacturer.

2.8.7.4 Cross Tees:2.8.7.4.1 Materials: Hot Dipped Galvanized steel 15/16 inch (23.8 mm) wide by 1-1/2

inch (38 mm) high by longest practical length with factory punched cross tee slots and hanger holes.

2.8.7.4.2 Capping: Identical to main runners.

2.8.8 15/16 inch (23.8 mm) Gasketed Exposed Grid2.8.8.1 Non-fire Rated Grid: Chicago Metallic, BarrierGrid with gaskets.2.8.8.2 Heavy Duty.2.8.8.3 Main Runners:

2.8.8.3.1 Materials: Hot Dipped Galvanized steel 15/16 inch (23.8 mm) wide by 1-1/2 inch high (38 mm) high by 144 inch (3657 mm) long with factory punched cross tee slots, hanger holes, and integral bayonet-style end couplings.

2.8.8.3.2 Capping: Aluminum affixed to 1-3/8 inch (35 mm) flange.2.8.8.4 Cross Tees:

2.8.8.4.1 Materials: Hot Dipped Galvanized steel 15/16 inch (23.8 mm) wide by 1-1/2 inch (38 mm) high by longest practical length with factory punched cross tee slots, hanger holes, and stab in couplings.

2.8.8.4.2 Capping: Identical to main runners.2.8.8.5 Gasket Materials:

2.8.8.5.1 Machine applied to edge of the tee. Gasket must have a 1/8 inch (3.175 mm) overhang on all cross tees.

2.8.8.5.2 Closed cell PVC foam resists UV oxidation, mildew and fungus, conformable to smooth and irregular surfaces, sealing against water, moisture, dirt and air-infiltration when compressed 30%.

2.8.8.5.3 Elastomeric construction adjust to thermal movement of structural elements without leaking and remain flexible.

2.8.8.5.4 Dimensionally stable and will not drip, ooze, or run when under compression. Gasket remains flexible at low temperatures, has excellent chemical resistance and forms an acoustic seal.

2.8.8.5.5 Average density of 8 lb./cu. ft. (128 kg./cu. m) and a compression deflection of 2 psi (13.7 kPa) per ASTM D1667.

2.9 METAL EDGE MOLDING AND TRIM

2.9.1 Roll-Formed, Sheet-Metal Edge Moldings and Trim:2.9.1.1 Profile: Rockfon Infinity profile perimeter trim for T-bar type grid acoustical

ceilings.2.9.1.1.1 Size: 2 inch (50 mm) high with horizontal face.2.9.1.1.2 Size: 4 inch (100 mm) high with horizontal face.2.9.1.1.3 Size: 6 inch (150 mm) high with horizontal face.2.9.1.1.4 Size: 8 inch (200 mm) high with horizontal face.2.9.1.1.5 Size: 10 inch (250 mm) high with horizontal face.2.9.1.1.6 Size: 12 inch (300 mm) high with horizontal face.2.9.1.1.7 Panels to be straight as indicated on approved drawings.2.9.1.1.8 Panels to be curved as indicated on approved drawings.

09 51 00-24

2.9.1.1.9 Corners to be factory mitered.2.9.1.1.10 90 degree corner kits are allowed in place of mitered corners on straight

sections.

2.9.2 Roll-Formed, Sheet-Metal Edge Moldings and Trim:2.9.2.1 Profile: Rockfon Infinity profile perimeter trim for 5/8 inch (16 mm) drywall

ceilings.2.9.2.1.1 Size: 4 inch (100 mm) high with 3/4 inch (19 mm) horizontal face and 1/2

inch (12.7 mm) wide by 3/4 inch (19 mm) deep continuous open reveal.2.9.2.1.2 Size: 6 inch (150 mm) high with 3/4 inch (19 mm) horizontal face and 1/2

inch (12.7 mm) wide by 3/4 inch (19 mm) deep continuous open reveal.2.9.2.1.3 Panels to be straight as indicated on approved drawings.2.9.2.1.4 All corners to be factory mitered.

2.9.3 Roll-Formed, Sheet-Metal Edge Moldings and Trim:2.9.3.1 Profile: Rockfon Infinity R Reveal profile perimeter trim for T-bar type grid

acoustical ceilings.2.9.3.1.1 Size: 4 inch (100 mm) with 1 inch (25 mm) horizontal face taping flange

grooved to accept joint compound.2.9.3.1.2 Size: 8 inch (200 mm) with 1 inch (25 mm) horizontal face taping flange

grooved to accept joint compound.2.9.3.1.3 Panels to be straight as indicated on approved drawings.2.9.3.1.4 Panels to be curved as indicated on approved drawings.2.9.3.1.5 Outer surface to be primed for adhesion of joint compound and field

applied paint finish. Field applied paint color.

2.9.4 Roll-Formed, Sheet-Metal Edge Moldings and Trim:2.9.4.1 Profile: Rockfon Infinity Z Razor profile for T-bar type grid acoustical ceilings.

2.9.4.1.1 Size: 6 inch (150 mm) wide horizontal face by 1-5/8 inch (41 mm) high.2.9.4.1.2 Panels to be straight as indicated on approved drawings.2.9.4.1.3 All corners to be factory mitered, maximum 45 degrees.

2.9.5 Splice Plate: Manufactured from galvanized steel with set screw for splicing sections of perimeter trim.

2.9.6 Grid Clips: Manufactured from galvanized steel with set screw for attaching perimeter trim to suspension system members.

2.9.7 Paired Bracket: Manufactured from electro-galvanized steel and used for back-to-back Infinity installations. Size bracket to maintain panel vertical surfaces as follows:2.9.7.1 2-1/4 inch (57 mm) apart with 3/4 inch (19 mm) opening at bottom.2.9.7.2 2-7/8 inches (73 mm) apart with 1-3/8 inch (35 mm) opening at bottom.2.9.7.3 As shown on the Drawings.

2.10 ACCESSORIES

2.10.1 Gypsum Access Doors: Glass reinforced gypsum designed specifically for use with suspended drywall ceilings, taped and finished to integrate with a minimum of visible lines. Provide in the following size:2.10.1.1 9 inch (228 mm) square.2.10.1.2 12 inch (304 mm) square.2.10.1.3 18 inch (457 mm) square.2.10.1.4 24 inch (609 mm) square.2.10.1.5 30 inch (762 mm) square.

2.10.2 Angle Moldings:2.10.2.1 Angle Moldings: Manufactured from 0.020 inch (0.5 mm) thick steel, 3/4 inch (19

09 51 00-25

mm) wide, height as recommended by manufacturer, by longest length practical for project applications. Finish identical to main tees and cross tees.

2.10.2.2 Angle Moldings: Manufactured from 0.020 inch (0.5 mm) thick steel, 15/16 inch (24 mm) wide, height as recommended by manufacturer, by longest length practical for project applications. Finish identical to main tees and cross tees.

2.10.2.3 Angle Moldings: Manufactured from 0.020 inch (0.5 mm) thick steel, 7/8 inch (22 mm) wide, height as recommended by manufacturer, by longest length practical for project applications. Finish identical to main tees and cross tees.

2.10.3 Channel Moldings:2.10.3.1 Manufactured from 0.018 inch (0.45 mm) thick steel with factory applied

standard white baked-on enamel paint finish.

2.10.4 Shadow Line Moldings:2.10.4.1 Manufactured from 0.020 inch (0.5 mm) thick steel with hemmed edge. Finished

with factory applied standard baked-on enamel paint.

2.10.5 Chicago Metallic 1493 Unopposed Tee Clips:2.10.5.1 Manufactured of galvanized steel.2.10.5.2 Provide where code compliant connection is needed and two cross tees are not

connected or where a cross tee does not have another cross tee to engage the end.

2.10.6 Chicago Metallic 1494 Seismic Separation Joint Clips:2.10.6.1 Used in IBC category D, E, and F seismic zones as an alternate method of

creating a traditional separation joint.2.10.6.2 The 1494 clip can be used to create a ceiling joint across a main runner or cross

tee and can be used to create a 2 directional movement in a ceiling.2.10.6.3 Carrying only one clip reduces inventory and installation mistakes are reduced

with our locator notches and locator tab.

2.10.7 Chicago Metallic 1496 Seismic Perimeter Clips:2.10.7.1 Used in IBC category C, D, E, and F seismic zones as an alternate method of

stabilizing the perimeters of suspended ceiling components.2.10.7.2 Allows tees to move into or away from the wall angle and has been tested and

recognized as an alternate method of stabilizing tees at the perimeter.2.10.7.3 Refer to ICCES ESR #2631 for more information.2.10.7.4 Bright gold color makes clips easily identifiable on the job site.

2.10.8 Acoustic Sealant for Perimeter Moldings: Specified in Section 07 90 00 - Joint Protection.

2.10.9 Gasket for Perimeter Moldings: Where gasket is not factory installed but required for particular applications, provide closed cell rubber sponge tape.

2.11 FINISHES

2.11.1 Provide the following factory finish:2.11.1.1 White.2.11.1.2 Match ceiling units.2.11.1.3 As selected by the Architect from manufacturers full range.2.11.1.4 As scheduled.2.11.1.5 ________.

3 EXECUTION

3.1 EXAMINATION

09 51 00-26

3.1.1 Do not begin installation until substrates have been properly prepared.

3.1.2 Verify layout of hangers will not interfere with other work.

3.1.3 Verify acoustical unit layout conditions, which will adversely affect installation.

3.1.4 If layout or substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.1.5 Verify wet work such as plastering and concrete is complete and dry. Verify building is enclosed and under standard occupancy conditions prior to start of installation.

3.1.6 Commencement of installation constitutes Installer's acceptance of substrate conditions.

3.2 PREPARATION

3.2.1 Clean surfaces thoroughly prior to installation.

3.2.2 Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 INSTALLATION

3.3.1 Install in accordance with manufacturer's instructions and in proper relationship with adjacent construction, including the following:3.3.1.1 Comply with ASTM C636 and seismic design requirements indicated, according

to manufacturer's written instructions and CISCA's "Ceiling Systems Handbook".3.3.1.2 Install hangers plumb and free from contact with insulation or other objects within

ceiling plenum that are not part of supporting structure or of ceiling suspension system.

3.3.1.3 Additional Hanger Wires: Wrapped tightly 3 full turns to structure and component at locations where imposed loads could cause deflection exceeding 1/360 span or tolerances specified below.

3.3.2 Measure each ceiling area and establish layout of acoustical panels to balance border widths at opposite edges of each ceiling. Avoid using less-than-half-width panels at borders.

3.3.3 Suspend ceiling hangers from building's structural members, plumb and free from contact with insulation or other objects within ceiling plenum. Splay hangers only where required and, if permitted with fire-resistance-rated ceilings, to miss obstructions; offset resulting horizontal forces by bracing, countersplaying, or other equally effective means.

3.3.4 Where width of ducts and other construction within ceiling plenum produces hanger spacings that interfere with location of hangers, use trapezes or equivalent devices. When steel framing does not permit installation of hanger wires at spacing required, install carrying channels or other supplemental support for attachment of hanger wires.

3.3.5 Do not support ceilings directly from permanent metal forms or floor deck; anchor into concrete slabs.

3.3.6 Do not attach hangers to steel deck tabs.

3.3.7 Install edge moldings and trim of type indicated at perimeter of acoustical ceiling area and where necessary to conceal edges of acoustical panels. Screw attach moldings to substrate at intervals not more than 16 inches (400 mm) o.c. and not more than 3 inches (75 mm) from ends. Miter corners accurately and connect securely.

3.3.8 Install suspension system runners so they are square and securely interlocked with one

09 51 00-27

another. Remove and replace dented, bent, or kinked members.

3.3.9 Install seismic separation tees so they are square and securely interlocked with one another, and in compliance with requirements of authority having jurisdiction.

3.3.10 Angle Moldings: Install on vertical surfaces, intersecting suspension components as recommended by the manufacturer.

3.3.11 Channel Moldings: Install on vertical surfaces, intersecting suspension components as recommended by the manufacturer.

3.3.12 Shadow Line Moldings: Install on vertical surfaces, intersecting suspension components as recommended by the manufacturer.

3.3.13 Install edge moldings and trim of type indicated at perimeter of acoustical ceiling area and where necessary to conceal edges of acoustical panels.3.3.13.1 Screw attach moldings to substrate at intervals not more than 16 inches (400

mm) on center and not more than 3 inches (75 mm) from ends, leveling with ceiling suspension system to a tolerance of 1/8 inch in 12 feet (3.2 mm in 3.6 m).

3.3.13.2 Miter corners accurately and connect securely.3.3.13.3 Do not use exposed fasteners, including pop rivets, on moldings and trim.

3.3.14 Acoustic Units:3.3.14.1 Fit acoustic units in place, free from damaged edges or other defects detrimental

to appearance and function.3.3.14.2 Lay directional patterned units in accordance with the approved reflected ceiling

plan. Fit border trim neatly against abutting surfaces.3.3.14.3 Install units after above ceiling work is complete.3.3.14.4 Install acoustic units level, in uniform plane, and free from twist, warp, and dents.

Press panels from above to set into grids. Do not pull from face.3.3.14.5 Cutting Acoustic Units:

3.3.14.5.1 Cut to fit irregular grid and perimeter edge trim.3.3.14.5.2 Cut square reveal edges to field cut units.3.3.14.5.3 Cut bevel edges to field cut units.

3.3.14.6 Where bullnose or round corners or obstructions occur, install preformed closures to match perimeter molding.

3.4 ERECTION TOLERANCES

3.4.1 Maximum Variation from Flat and Level Surface: 1/8 inch in 10 feet (3 mm in 3 m).

3.4.2 Maximum Variation from Plumb of Grid Members Caused by Eccentric Loads: 2 degrees.

3.5 PROTECTION AND CLEANING

3.5.1 Protect installed products until completion of project.

3.5.2 Clean adjacent surfaces and remove unused materials and debris from site.

3.5.3 Clean exposed surfaces in accordance with manufacturer's written instructions.

3.5.4 Remove and reinstall improperly installed material.

3.5.5 Remove damaged components, replace with undamaged components.

3.5.6 Touch-up, repair or replace damaged units until satisfactory results are obtained.

3.5.7 Clean with non-solvent based non-abrasive commercial cleaning solution.

09 51 00-28

3.6 SCHEDULES

3.6.1 Type ____:3.6.1.1 Acoustical Units: _____.3.6.1.2 Suspension System: _____.



END OF SECTION

09 51 00-29

ARCAT€¦ · Web viewRockfon is a subsidiary of Denmark-based ROCKWOOL International A/S, the world's largest producer of stone wool products.For the past 25 years, the ROCKWOOL

Documents