Appendix A. System Check Plots Table of contents · Appendix A. System Check Plots . Table of contents . ... Medium parameters used: ... Reference Value = 50.94 V/m; ...

Appendix No.: SYBH(Z-SAR)019042017-2A FCC ID:QISBAC-LX3

Appendix A. System Check Plots

Table of contents

SystemPerformanceCheck-D750-EX-Head

SystemPerformanceCheck-D750-EX-Body

SystemPerformanceCheck-D835-ES-Head



SystemPerformanceCheck-D835-ES-Body























Date: 2017-5-10

Test Laboratory: HUAWEI SAR/HAC Lab


DUT: Dipole 750 MHz D750V3; Type: D750V3; Serial: D750V3 - SN:1044

Communication System: UID 0, CW (0); Frequency: 750 MHz;Duty Cycle: 1:1Medium parameters used: f = 750 MHz; σ = 0.894 S/m; εr = 42.488; ρ = 1000 kg/m3

Phantom section: Flat Section

DASY Configuration:

� Probe: EX3DV4 - SN3744; ConvF(9.7, 9.7, 9.7); Calibrated: 2016-7-26; � Sensor-Surface: 1.4mm (Mechanical Surface Detection), z = 1.0, 31.0 � Electronics: DAE4 Sn852; Calibrated: 2017-4-27 � Phantom: SAM3; Type: SAM; Serial: TP-1597 � DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331)

Configuration/d=15mm, Pin=250mW/Area Scan (6x14x1): Measurement grid: dx=15mm, dy=15mmMaximum value of SAR (measured) = 2.49 W/kg

Configuration/d=15mm, Pin=250mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mmReference Value = 50.94 V/m; Power Drift = -0.02 dBPeak SAR (extrapolated) = 3.23 W/kgSAR(1 g) = 2.15 W/kg; SAR(10 g) = 1.41 W/kgMaximum value of SAR (measured) = 2.88 W/kg

0 dB = 2.88 W/kg = 4.59 dBW/kg

Date: 2017-5-9






DASY Configuration:




0 dB = 3.00 W/kg = 4.77 dBW/kg

Date: 2017-5-4



DUT: Dipole 835 MHz D835V2; Type: D835V2; Serial: D835V2 - SN:4d059

Communication System: UID 0, CW; Frequency: 835 MHz;Duty Cycle: 1:1Medium parameters used: f = 835 MHz; σ = 0.916 S/m; εr = 40.282; ρ = 1000 kg/m3


DASY Configuration:

� Probe: ES3DV3 - SN3168; ConvF(6.68, 6.68, 6.68); Calibrated: 2016-9-27; � Sensor-Surface: 3mm (Mechanical Surface Detection), z = 2.0, 32.0 � Electronics: DAE4 Sn851; Calibrated: 2016-7-22 � Phantom: SAM1; Type: SAM; Serial: TP-1475 � DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331)



0 dB = 2.69 W/kg = 4.30 dBW/kg

Date: 2017-5-11






DASY Configuration:




0 dB = 2.59 W/kg = 4.13 dBW/kg

Date: 2017-5-13






DASY Configuration:




0 dB = 3.18 W/kg = 5.02 dBW/kg

Date: 2017-5-5






DASY Configuration:

� Probe: ES3DV3 - SN3168; ConvF(6.33, 6.33, 6.33); Calibrated: 2016-9-27; � Sensor-Surface: 3mm (Mechanical Surface Detection), z = 2.0, 32.0 � Electronics: DAE4 Sn851; Calibrated: 2016-7-22 � Phantom: SAM2; Type: SAM; Serial: TP:1474 � DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331)



0 dB = 2.65 W/kg = 4.23 dBW/kg

Date: 2017-5-7






DASY Configuration:




0 dB = 3.32 W/kg = 5.21 dBW/kg

Date: 2017-5-10






DASY Configuration:




0 dB = 2.59 W/kg = 4.13 dBW/kg

Date: 2017-5-9






DASY Configuration:


Configuration/d=10mm pin=250mW/Area Scan (6x10x1): Measurement grid: dx=15mm, dy=15mmMaximum value of SAR (measured) = 9.29 W/kg

Configuration/d=10mm pin=250mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mmReference Value = 87.53 V/m; Power Drift = -0.12 dBPeak SAR (extrapolated) = 16.4 W/kgSAR(1 g) = 9.08 W/kg; SAR(10 g) = 4.79 W/kgMaximum value of SAR (measured) = 11.5 W/kg

0 dB = 9.29 W/kg = 9.68 dBW/kg

Date: 2017-5-13






DASY Configuration:



Configuration/d=10mm pin=250mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mmReference Value = 85.26 V/m; Power Drift = 0.01 dBPeak SAR (extrapolated) = 16.0 W/kgSAR(1 g) = 8.78 W/kg; SAR(10 g) = 4.63 W/kgMaximum value of SAR (measured) = 11.1 W/kg

0 dB = 7.89 W/kg = 8.97 dBW/kg

Date: 2017-5-22






DASY Configuration:




0 dB = 8.22 W/kg = 9.15 dBW/kg

Date: 2017-5-5






DASY Configuration:




0 dB = 8.33 W/kg = 9.21 dBW/kg

Date: 2017-5-9






DASY Configuration:




0 dB = 7.87 W/kg = 8.96 dBW/kg

Date: 2017-5-22






DASY Configuration:




0 dB = 12.1 W/kg = 10.83 dBW/kg

Date: 2017-5-24






DASY Configuration:

� Probe: EX3DV4 - SN3744; ConvF(7.61, 7.61, 7.61); Calibrated: 2016-7-26; � Sensor-Surface: 1.4mm (Mechanical Surface Detection), z = 1.0, 31.0 � Electronics: DAE4 Sn851; Calibrated: 2016-7-22 � Phantom: SAM2; Type: SAM; Serial: TP:1474 � DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331)



0 dB = 9.17 W/kg = 9.62 dBW/kg

Date: 2017-5-4






DASY Configuration:




0 dB = 8.58 W/kg = 9.33 dBW/kg

Date: 2017-5-12






DASY Configuration:




0 dB = 12.7 W/kg = 11.04 dBW/kg

Date: 2017-5-18


SystemPerformanceCheck-1900-EX-Head




DASY Configuration:




0 dB = 16.5 W/kg = 12.18 dBW/kg

Date: 2017-5-7






DASY Configuration:



Configuration/d=10mm pin=250mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mmReference Value = 89.14 V/m; Power Drift = 0.01 dBPeak SAR (extrapolated) = 19.2 W/kgSAR(1 g) = 10.7 W/kg; SAR(10 g) = 5.55 W/kgMaximum value of SAR (measured) = 13.6 W/kg

0 dB = 8.41 W/kg = 9.25 dBW/kg

Date: 2017-5-19






DASY Configuration:




0 dB = 9.78 W/kg = 9.90 dBW/kg

Date: 2017-5-21


SystemPerformanceCheck-1900-EX-Body




DASY Configuration:




0 dB = 16.5 W/kg = 12.18 dBW/kg

Date: 2017-5-26






DASY Configuration:




0 dB = 15.0 W/kg = 11.76 dBW/kg

Date: 2017-6-30






DASY Configuration:



Configuration/d=10mm, Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mmReference Value = 104.8 V/m; Power Drift = 0.17 dBPeak SAR (extrapolated) = 27.1 W/kgSAR(1 g) = 13.1 W/kg; SAR(10 g) = 6.14 W/kgMaximum value of SAR (measured) = 17.2 W/kg

0 dB = 14.3 W/kg = 11.55 dBW/kg

Date: 2017-5-27






DASY Configuration:




0 dB = 17.9 W/kg = 12.53 dBW/kg

Date: 2017-5-14






DASY Configuration:




0 dB = 25.6 W/kg = 14.08 dBW/kg

Date: 2017-5-16






DASY Configuration:




0 dB = 17.8 W/kg = 12.50 dBW/kg

Date: 2017-5-23






DASY Configuration:




0 dB = 17.2 W/kg = 12.36 dBW/kg

Date: 2017-5-26






DASY Configuration:




0 dB = 17.1 W/kg = 12.33 dBW/kg

Date: 2017-6-28






DASY Configuration:




0 dB = 15.1 W/kg = 11.79 dBW/kg

page 1 of 2

System Validation

Per FCC KDB 865664 D02, SAR system verification is required to confirm

measurement accuracy. The SAR systems (including SAR probes, system

components and software versions) used for this device were validated against its

performance specifications prior to the SAR measurements. Reference dipoles are

used with the required tissue-equivalent media for system validation, according to the

procedures outlined in FCC KDB 865664 D01 and IEEE 1528-2013.Since SAR probe

calibrations are frequency dependent, each probe calibration point must be validated

at a frequency within the valid frequency range of the probe calibration point, using

the system that normally operates with the probe for routine SAR measurements and

according to the required tissue-equivalent media.

a tabulated summary of the system validation status, measurement frequencies, SAR

probes, calibrated signal type(s) and tissue dielectric parameters has been included.

page 2 of 2

Table of SAR System validation summary:

FREQ.

[Mhz] DATE

PROBE

SN

PROBE

TYPE

PROBE CAL

POINT

PERM

(εr)

COND

(σ)

CW VALIDATION MOD.VALIDATION

SENSI-

TIVITY

PROBE

LINARITY

PROBE

ISOTROPY

MOD.

TYPE

DUTY.

FACTORE PAR

750 2016/08/23 3744 EX3DV4 750 Head 43.17 0.894 PASS PASS PASS N/A N/A N/A

835 2016/08/15 3744 EX3DV4 835 Head 41.06 0.891 PASS PASS PASS GMSK PASS N/A

835 2016/09/30 3168 ES3DV3 835 Head 42.72 0.940 PASS PASS PASS GMSK PASS N/A

1750 2016/09/30 3168 ES3DV3 1750 Head 40.13 1.370 PASS PASS PASS NA NA N/A

1900 2016/08/17 3744 EX3DV4 1900 Head 39.66 1.412 PASS PASS PASS GMSK PASS N/A

1900 2016/09/30 3168 ES3DV3 1900 Head 38.55 1.410 PASS PASS PASS GMSK PASS N/A

2450 2016/08/10 3744 EX3DV4 2450 Head 39.51 1.805 PASS PASS PASS OFDM/TDD PASS PASS

2600 2016/08/14 3744 EX3DV4 2600 Head 37.88 1.927 PASS PASS PASS TDD PASS N/A

750 2016/08/24 3744 EX3DV4 750 Body 53.28 0.963 PASS PASS PASS N/A N/A N/A

835 2016/08/27 3744 EX3DV4 835 Body 53.44 0.990 PASS PASS PASS GMSK PASS N/A

835 2016/10/07 3168 ES3DV3 835 Body 56.00 1.002 PASS PASS PASS GMSK PASS N/A

1750 2016/10/07 3168 ES3DV3 1750 Body 52.46 1.440 PASS PASS PASS N/A N/A N/A

1750 2016/08/21 3744 EX3DV4 1750 Body 53.72 1.438 PASS PASS PASS N/A N/A N/A

1900 2016/08/18 3744 EX3DV4 1900 Body 51.98 1.517 PASS PASS PASS GMSK PASS N/A

1900 2016/10/07 3168 ES3DV3 1900 Body 51.94 1.550 PASS PASS PASS GMSK PASS N/A

2450 2016/09/02 3744 EX3DV4 2450 Body 51.88 2.004 PASS PASS PASS OFDM/TDD PASS PASS

2600 2016/08/20 3744 EX3DV4 2600 Body 53.15 2.153 PASS PASS PASS TDD PASS N/A

2600 2016/10/07 3168 ES3DV3 2600 Body 51.55 2.165 PASS PASS PASS TDD PASS N/A

NOTE: While the probes have been calibrated for both CW and modulated signals, all

measurements were performed using communication systems calibrated for CW

signals only. Modulations in the table above represent test configurations for which

the measurement system has been validated per FCC KDB Publication 865664D01

for scenarios when CW probe calibrations are used with other signal types. SAR

systems were validated for modulated signals with a periodic duty cycle, such as

GMSK, or with a high peak to average ratio (>5dB), such as OFDM according to KDB

865664.

Appendix A. System Check Plots Table of contents · Appendix A. System Check Plots . Table of contents . ... Medium parameters used: ... Reference Value = 50.94 V/m; ...

Documents