2019.08 With minimum surface preparation Excellent workability and surprising anti-rust performance !! Somay-Q’s anti-rust solution can shorten the lengthy surface preparation process. Restrain the rust with only one or two application. Less coating process, save material costs and shortening the drying time. Realize the huge cost savings. Before Before After After Before Before After After Process chart for repairing holes created by rust and Rust preventive system Working process and scope Loose rust corroded hole 1. Hammering Remove loose rust 2. Sanding with a wire brush SSPC-SP-2 or 3 3. Denting hole created by rust Dent rusted hole with up to 3 cm depth and with 5cm width from its edge as shown. 4. Preparing for reinforcing plate Prepare for reinforcing plate with 0.5-1cm thickness. (Sand both reinforcing plate with 100 grit sandpaper.) 7. Reinforcing Insert reinforcing plate into the hole. 8. Fixing reinforcing plate NO MORE RUST POWER FILLER liberally. 9. Sanding Sand putty with #120-180 grit sandpaper. 10. Undercoating POWER BOUSEI EP039 11. Topcoating NO MORE RUST AP089 5971 Moto-kurihashi, Goka, Sashima-gun, Ibaraki 306-0313 PHONE : +81-280-80-0005 FAX： +81-280-80-0006 E-mail : [email protected] http : //www.somayq.com TECHNOLOGY Inc. No matter how terrible the rust is at various sites Anti-rust series 5. NO MORE RUST SEALER NO MORE RUST SEALER On rusted surface - Apply it until rusted surface is glossy. On reinforcing plate ‒ Apply it thinly Allow to dry for 30-40 minutes at room temperature. 6. NO MORE RUST POWER FILLER Apply as shown by arrow. NO MORE RUST POWER FILLER
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
2019.08
With minimum surface preparationExcellent workability andsurprising anti-rust performance !!Somay-Q’s anti-rust solution can shorten the lengthy surface preparation process.Restrain the rust with only one or two application.Less coating process, save material costs and shortening the drying time.Realize the huge cost savings.
BeforeBefore AfterAfter
BeforeBefore AfterAfter
Process chart for repairing holes created by rust and Rust preventive system
Working process and scopeLoose rust
corroded hole
1. Hammering
Remove loose rust
2. Sanding with a wire brush
SSPC-SP-2 or 3
3. Denting hole created by rust
Dent rusted hole with up to 3 cm depth and with 5cm width from its edge as shown.
4. Preparing for reinforcing plate
Prepare for reinforcing plate with 0.5-1cm thickness. (Sand both reinforcing plate with 100 grit sandpaper.)
7. Reinforcing
Insert reinforcing plate into the hole.
8. Fixing reinforcing plate
NO MORE RUST POWER FILLER liberally.
9. Sanding
Sand putty with #120-180 grit sandpaper.
10. Undercoating
POWER BOUSEI EP039
11. Topcoating
NO MORE RUST AP089
5971 Moto-kurihashi, Goka, Sashima-gun, Ibaraki 306-0313PHONE: +81-280-80-0005 FAX： +81-280-80-0006E-mail : [email protected] http : //www.somayq.com
TECHNOLOGY Inc.
No matter how terrible the rustis at various sites
Anti-rust series
5. NO MORE RUST SEALER
NO MORE RUST SEALER
On rusted surface - Apply it until rusted surface is glossy. On reinforcing plate ‒ Apply it thinlyAllow to dry for 30-40 minutes at room temperature.
6. NO MORE RUST POWER FILLER
Apply as shown by arrow.
NO MORE RUSTPOWER FILLER
For repair and new installation ! Huge cost saving !Excellent workability, Strong Anti-rust capability ! Primer for any rusted points !
※DIRECTIONS FOR USE.Please read the product catalog for each product.NO MORE RUST series
NO MORE RUST SEALER NO MORE RUST POWER FILLER
Color
Strong one-component permeable anti-rust primer which permeates into the rust deeply and locks its proliferation.Excellent workability without limiting the applicable surfaces such as over coating, rare metal and rusted surfaces.※Please inquire us if you intend to apply the epoxy based coating as a topcoat.
Putty with Strong anti-rust power, flexibility, anti-shock ability and adhesion power.Not only for metal such as galvanium and molten zinc, but the application is extended to woods, concrete, plastic and even FRP.Pitting corrosion can be fixed, even where the welding is not a choice.
Silver
NO MORE RUST EP039
Primer coatingfor the rusting points.
Rust Preventive Undercoat
Rust Preventive Primer
Rust Preventive Repairing Agent
Color Brown(almost transparent)Substrates Alminium, Stainless steel, steel,
galvanized steel (both cold and hot dipped),concrete etc
Top coat for EP039Strong coating suppresses the rust for a long period with superb Anticorrosion, Weatherproof and Chemical resistance performancesAnti-rust top coat which has a capability of forming the ‘anti-shock’ strong coating with the excellent anticorrosion, weatherproof and chemical resis-tance for a long period.It contains NO hazardous heavy metal such as lead and chrome.Compatible with NO MORE RUST EP039 and enhances the anti-rust effect by using NO MORE RUST AP089 as the top coat.
Strong coating suppressesthe rust for a long period.
NO MORE RUST AP089 PART A/PART B
rust preventive topcoat
for outdoor use
With only one application, it forms a DTF of 150μm coating at minimum preparation. It alone can suppress the rust strongly. Applicable for various surfaces such as rusted, hot-dip galvanized, stainless, aluminum, concrete and coated, with superb anti-rust, chemical resistance and wear resistance.
Only one application andalone can suppress the rust.
NO MORE RUST EP1000 SET
rust preventive topcoat
(for indoor use)
●Rusted surfaces●Galvanized steel (both cold and hot dipped)●Concrete●Structural steel●Steel plates, etc.
Substrates●Rusted surfaces●Galvanized steel (both cold and hot dipped)●Aluminum●Stainless steel●Existing finish●Concrete●Tile etc.
Substrates
※1set=PART A + PART B (5 kg can, ea.)
Size Spreading Rate
265 g/㎡
Quantity1 set
4cans
Product※NO MORE RUST EP039
EP REDUCER10kg
3.7L
Size Quantity
4cans
Product
NO MORE RUST POWER FILLER 4kg
Size Spreading Rate
120g/㎡
Quantity1
1
4cans
Product
NO MORE RUST AP089 PART ANO MORE RUST AP089 PART BAP REDUCER
3.5kg
0.7kg
3.7L
Size Spreading Rate
320g/㎡
Quantity1
1
4cans
Product
NO MORE RUST EP1000 PART ANO MORE RUST EP1000 PART BEP REDUCER
4.5kg/4kg
5kg
3.7L
Size Spreading Rate
50～100g/㎡
Quantity1cans
4cans
6cans
6cans
Product
NO MORE RUST SEALER
16L
3.7L
0.9L
0.3L
The quantity of NO MORE RUST EP1000 PART A shall vary depends on its color.
NO MORE RUST POWER HARDENER J(sold separately)
Color : BlueQuantity : 80gMixture Ratio : Putty 100 : hardener 2 by weight ratio
Related Documents
