This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Published by the ISO 15156 Maintenance Agency (DIN-Germany), and by NACE International, Houston, Texas, USA.
Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production —
Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys
TECHNICAL CIRCULAR 1
Industries du pétrole et du gaz naturel — Matériaux pour utilisation dans des environnements contenant de l'hydrogène sulfuré (H2S) dans la production de pétrole et de gaz —
Partie 3: ARC (alliages résistants à la corrosion) et autres alliages résistants à la fissuration
CIRCULAIRE TECHNIQUE 1
Technical Circular 1 to ANSI/NACE MR0175/ISO 15156-3 was prepared by the NACE/ISO 15156 Maintenance Agency on behalf of Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries.
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ ORGANISATION INTERNATIONALE DE NORMALISATION
INTERNATIONAL STANDARD ANSI/NACE MR0175/ISO 15156-3:2009 TECHNICAL CIRCULAR 1:2011 Published 2011-06-14
Srinivasan Ragahven - Invoice INV-511741-XGJRGJ, downloaded on 1/8/2012 12:23:26 AM - Single-user license only, copying and networking prohibited.
The establishment of the NACE/ISO 15156 Maintenance Agency was confirmed by the ISO Technical Management Board in June 2007. A copy of the TMB Vote-Form Number: 34/2007 giving the rules of procedure for the maintenance agency can be obtained from the ISO TMB Secretariat. It is also available from the ISO 15156 Web site at www.iso.org/iso15156maintenance. ANSI/NACE MR0175/ISO 15156 series has, since publication, been amended by a number of Technical Corrigenda and Technical Circulars and consists of the following parts, under the general title Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production:
Part 1: General principles for selection of cracking-resistant materials (2009)
Part 2: Cracking-resistant carbon and low alloy steels, and the use of cast irons (2009)
As applicable, subsequent publications resulting in new editions of an individual part of ANSI/NACE MR0175/ISO 15156 effectively replace the corresponding set of documents shown above. Information on the latest status of these documents can be obtained from www.iso.org/iso15156maintenance.
Srinivasan Ragahven - Invoice INV-511741-XGJRGJ, downloaded on 1/8/2012 12:23:26 AM - Single-user license only, copying and networking prohibited.
Replace ―NACE TM0177-96, Laboratory testing of metals for resistance to sulfide stress cracking and stress corrosion cracking in H2S environments,” with the following:
NACE TM0177, Laboratory testing of metals for resistance to sulfide stress cracking and stress corrosion cracking in H2S environments
Page 52, Clause B.3.1
Replace ―NACE TM0177-96‖ with NACE TM0177
Page 56, Clause B.3.7, Paragraph 1
Replace ―NACE TM0177-96‖ with NACE TM0177
Page 56, Clause B.4, Paragraph 2
Replace ―NACE TM0177-96‖ with NACE TM0177
Page 57, Clause B.5, Paragraph 2
Replace ―NACE TM0177-96‖ with NACE TM0177
Page 57, Clause B.8 a)
Replace ―NACE TM0177-96‖ with NACE TM0177
Page 57, Clause B.8 b)
Replace ―NACE TM0177-96‖ with NACE TM0177
Srinivasan Ragahven - Invoice INV-511741-XGJRGJ, downloaded on 1/8/2012 12:23:26 AM - Single-user license only, copying and networking prohibited.
Table D.1 — Chemical compositions of some austenitic stainless steels (see Clauses A.2 and D.3)
UNS C Cr Ni Mn Si P S Mo N Other FPREN Ni 2Mo
max.a max.a max.a max. max. max.
wC wCr wNi wMn wSi wP wS wMo wN
% % % % % % % % %
J92500 0.03 17.0 to
21.0
8.0 to
12.0 1.50 2.00 0.04 0.04 — — — 17 to 21 8 to 12
J92600 0.08 18.0 to
21.0
8.0 to
11.0 1.50 2.00 0.04 0.04 — — — 18 to 21 8 to 11
J92800 0.03 17.0 to
21.0
9.0 to
13.0 1.50 1.50 0.04 0.04
2.0 to
3.0 — — 24 to 31 13 to 19
J92843 0.28 to
0.35
18.0 to
21.0
8.0 to
11.0
0.75 to
1.50 1.00 0.04 0.04
1.00 to
1.75 — Otherb 23 to 30 10 to 15
J92900 0.08 18.0 to
21.0
9.0 to
12.0 1.50 2.00 0.04 0.04
2.0 to
3.0 — — 24 to 31 13 to 18
S20100 0.15 16.0 to 18.0
3.5 to 5.5
5.5 to 7.5
1.00 0.060 0.030 — 0.25 — 20 to 22 4 to 6
S20200 0.15 17.0 to 19.0
4.0 to 6.0
7.5 to 10.0
1.00 0,060 0.030 — — — 17 to 19 4 to 6
S20500 0.12 to
0.25
16.0 to
18.0
1.00 to
1.75
14.0 to
15.5 1.00 0.060 0.030 — — — 16 to 18 1 to 2
S20910 0.06 20.5 to
23.5
11.5 to
13.5
4.0 to
6.0 1,00 0.040 0.030
1.5 to
3.0
0.20 to
0.40 Otherc 29 to 38 15 to 20
S30200 0.15 17.0 to
19.0
8.0 to
10.0 2.00 1.00 0.045 0.030 — — — 17 to 19 8 to 10
S30400 0.08 18.0 to
20.0
8.0 to
10.5 2.00 1.00 0.045 0.030 — — — 18 to 20 8 to 11
S30403 0.03 18.0 to
20.0
8.0 to
12.0 2.00 1.00 0.045 0.030 — — — 18 to 20 8 to 12
S30500 0.12 17.0 to
19.0
10.0 to
13.0 2.00 1.00 0.045 0.030 — — — 17 to 19 10 to 13
S30800 0.08 19.0 to
21.0
10.0 to
12.0 2.00 1.00 0.045 0.030 — — — 19 to 21 10 to 12
S30900 0.20 22.0 to
24.0
12.0 to
15.0 2.00 1.00 0.045 0.030 — — — 22 to 24 12 to 15
S31000 0.25 24.0 to
26.0
19.0 to
22.0 2.00 1.50 0.045 0.030 — — — 24 to 26 19 to 22
S31600 0.08 16.0 to
18.0
10.0 to
14.0 2.00 1.00 0.045 0.030
2.0 to
3.0 — — 23 to 28 14 to 20
S31603 0.030 16.0 to 18.0
10.0 to 14.0
2.00 1.00 0.045 0.030 2.0 to 3.0
— — 23 to 28 14 to 20
S31635 0.08 16 to 18 10 to 14 2.00 1.0 0.045 0.030 2 to 3 0.10 Otherd 23 to 30 14 to 20
S31700 0.08 18.0 to
20.0
11.0 to
15.0 2.00 1.00 0.045 0.030
3.0 to
4.0 — — 28 to 33 17 to 23
S32100 0.08 17.0 to
19.0
9.0 to
12.0 2.00 1.00 0.045 0.030 — — Otherd 17 to 19 9 to 12
S34700 0.08 17.0 to
19.0
9.0 to
13.0 2.00 1.00 0.045 0.030 — — Othere 17 to 19 9 to 13
S38100 0.08 17.0 to
19.0
17.5 to
18.5 2.00
1.50 to
2.50 0.03 0.030 — — — 17 to 19 18 to 19
a Where a range is shown, it indicates min. to max. percentage mass fractions. b Cu, 0.50 % max.; Ti, 0.15 % to 0.50 %; W, 1.00 % to 1.75 %; Nb Ta, 0.30 % to 0.70 %. c Nb, 0.10 % to 0.30 %; V, 0.10 % to 0.30 %. d Minimum value of Ti shall be five times the percentage mass fraction of carbon. e Minimum value of Nb shall be ten times the percentage mass fraction of carbon.
Srinivasan Ragahven - Invoice INV-511741-XGJRGJ, downloaded on 1/8/2012 12:23:26 AM - Single-user license only, copying and networking prohibited.