Page 1
www.wjpps.com Vol 8, Issue 12, 2019.
292
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
AN OVERVIEW ON NANOTECHNOLOGY
P. Divya*, Dr. A. Seetha Devi and M. Sri Rekha
India.
ABSTRACT
This chapter explores the basic definitions for nanotechnology, and
sketches a concept system for the field. Nano biotechnology is the
application of nanotechnology in biological fields. Nanotechnology is
a multidisciplinary field, which covers a vast and diverse array of
devices derived from engineering, biology, physics and chemistry.
The associated research and applications are equally diverse, ranging
from extensions of conventional physics to completely new
approaches based upon developing new materials with new dimensions on Nano scale.
Nanotechnology explores electrical, optical, and magnetic activity as well as structural
behavior at the molecular and sub molecular level. It has the potential to revolutionize a
series of medical and biotechnology tools and procedures so that they are portable, cheaper,
safer and easier to administer. The nanoparticles are generally classified into the organic,
inorganic and carbon based particles in nanometric scale that has improved properties
compared to larger sizes of respective materials. The nanoparticles show enhanced properties
such as high reactivity, strength, surface area, sensitivity, stability, etc. because of their small
size. The nanoparticles are synthesized by various methods for research and commercial uses
that are classified into three main types namely physical, chemical and mechanical processes
that has seen a vast improvement over time.
KEY WORDS: Nano particles, Method of preparation, Applications.
INTRODUCTION
Nanotechnology is the science of matter and material that deals with the particle size in
nanometers (1nm=10-9
m). The term „nano‟ is derived from Latin word, which means dwarf.
Nanotechnology deals with design, characterization and application of various structures,
devices systems by controlling the size and shape at nanometric scale. Pharmaceutical
Nanotechnology embraces applications of nano science to pharmacy as nanomaterials, and as
WORLD JOURNAL OF PHARMACY AND PHARMACEUTICAL SCIENCES
SJIF Impact Factor 7.632
Volume 8, Issue 12, 292-308 Review Article ISSN 2278 – 4357
Article Received on
10 Oct. 2019,
Revised on 30 Oct. 2019,
Accepted on 20 Nov. 2019,
DOI: 10.20959/wjpps201912-14920
*Corresponding Author
P. Divya
India.
Page 2
www.wjpps.com Vol 8, Issue 12, 2019.
293
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
devices like drug delivery, diagnostic, imaging and biosensor materials. Pharmaceutical
nanotechnology has provided more fine-tuned diagnosis and focused treatment of disease at
molecular level. It helps in detecting the antigen associated with diseases such as cancer,
diabetes mellitus, neurodegenerative diseases, as well as detecting the microorganisms and
virus associated with infections.
The size of the nanoparticle structure may ranges from upto 1 to 100nm in at least one
dimension. However, the prefix “Nano” is commonly used for particles that are up to several
hundred nanometres in size the drug is dissolved, entrapped, encapsulated or attached to this
nanoparticle matrix. Depending upon the method of preparation, nanoparticles, nanospheres
or nanocapsules can be obtained. Nanoparticles, particularly coated with hydrophilic polymer
such as poly ethylene glycol (PEG) known as long-circulating particles, used as a potential
drug delivery devices because of their ability to circulate for a prolonged period of time,
target to a particular organ, such as carrier of DNA in gene therapy.
bio nanotechnology, the incorporation of biological molecules into Nano artifacts. The
discovery of some of the mechanistic details of complicated biological machinery such as the
ribosome, which encodes the sequence of nucleic acids as a sequence of amino acids,
promotes assembler-based view of nanotechnology, and these biological machines provided a
kind of living proof of principle that elaborate and functionally sophisticated mechanisms
could operate at the Nanoscale. The highly refined molecular binding specificity is
particularly valued, and used to facilitate the assembly of unique structures from a solution of
precursors and for capturing chemicals from the environment prior to registering their
presence via a transducer (biosensors). A further application involves using the widely
encountered ability of biomolecules to easily accomplish actions associated with difficult and
extreme conditions in the artificial realm, such as the catalysis of many chemical reactions,
and optical nonlinearity with single photons, a feature which can be exploited to construct
optical computers. One might also mention the kidneys as a marvelous example of biological
Nano engineering that functions to extract certain substances from highly dilute solutions, an
operation which may become of increasing importance as conventionally processable ores
become depleted.[1,4]
Advantages
1. Increased surface area, oral bioavailability and rate of dissolution.
2. Decreases the dose of the drug required and reduces the number of doses.
Page 3
www.wjpps.com Vol 8, Issue 12, 2019.
294
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
3. Reduced mortality and morbidity rates and increased longevity in return.[5]
4. Nanotechnology is seen as a boon in the medical world, since these can help in creating
new drugs.
5. Nanotechnology could also be used to refine drug production, tailoring drugs at a
molecular level to make them more effective and reduce side effects.[6]
Different Nano Drug Delivery Systems Developed Using Nanotechnology Principles are
1. Nanoparticles.
2. Solid lipid nanoparticles.
3. Nanocrystals.
4. Nanosuspensions.
5. Nanoemulsions.
6. Nanospheres.
7. Nanocapsules.
8. Nanosponges.
Nanoparticles
Nanoparticles are defined as particulate dispersions or solid particles with a size in the range
of 10-1000nm.[7]
It‟s Coarse particles range between 10,000 and 2,500 nanometers. Fine
particles are in size range between 2,500 and 100 nanometers. Ultrafine particles or
nanoparticles are sized between 1 and 100 nanometers.[8]
The drug is dissolved, entrapped
and encapsulated or attached to this nanoparticle matrix.
Nanoparticles can be of two types depending upon the method of preparation:
1. Nanospheres: These have monolithic type system (matrix) in which drugs are either
adsorbed or dispersed.
2. Nanocapsules: In these drugs are adsorbed on to their exterior or entrapped in the core
also these particles exhibit a membrane wall structure.[9]
Page 4
www.wjpps.com Vol 8, Issue 12, 2019.
295
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
Figure 1: Types of nanoparticles.
Types of Nanoparticles[10]
Figure 1.1: Types of nanoparticles.
Advantages of Nanoparticles
1. Both passive and active drug targeting after parenteral administration can be easily
manipulated to achieve particle size and surface characteristics of nanoparticle.
2. The drug release may be controlled or sustained during the transportation at the site of
localization, which alters the organ distribution of the drug in order to achieve maximum
therapeutic efficacy and reduce the side effects.[11]
3. By the choice of matrix constituents like controlled release and particle degradation
characteristics can be readily modulated.[12]
4. They can be easily administered by various routes including nasal, oral, parenteral etc.
5. Drug loading in nanoparticles is relatively high as compared to other dosage forms.
Page 5
www.wjpps.com Vol 8, Issue 12, 2019.
296
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
6. Reduction in toxicity is also an important advantage of nanoparticles.
7. Use of nanoparticle can reduce dosing frequency thus increasing bioavailability of
drug.[13]
Preparation of Nanoparticles
Nanoparticles are aimed to be prepared from a variety of materials such as proteins,
polysaccharides and synthetic polymers. The selection criteria of matrix materials depends
on many factors such as: (a) Size of nanoparticles required; (b) Inherent properties of the
drug, e.g. aqueous solubility and stability; (c) Surface characteristics such as Charge and
Permeability; (d) Degree of biodegradability, biocompatibility and toxicity; (f)Antigenicity of
the final product.[14]
Nanoparticles are prepared by various methods of preparation including
1) Solvent evaporation method
2) Solvent diffusion method
3) Phase inversion temperature method
4) Super critical fluid method
5) Salting out
6) Spray drying
7) Polymerization method
8) Emulsification method
Solvent evaporation method: The polymer and hydrophobic drug is dissolved in an organic
solvent for solvent evaporation method. Oil in water (o/w) emulsion is formed when the
mixture of polymer and drug solution is added to the aqueous solution containing a surfactant
or emulsifying agent. The organic solvent is evaporated from the stable emulsion either by
reducing the pressure or by continuous stirring. The type and concentrations of stabilizer,
homogenizer speed and polymer concentration shows the effect on particles size. In order to
produce small particle size, often a high-speed homogenization or ultra-sonication may be
employed.[15]
Page 6
www.wjpps.com Vol 8, Issue 12, 2019.
297
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
Solvent diffusion method[16]
Figure 2: solvent diffusion method.
Phase inversion temperature method
In this process droplets of Nano emulsion are used to de solubilise the polymer to produce
nanoparticles. In this method polymer had been introduced earlier to produce Nano-emulsion,
the oil is substituted by volatile solvent, the nanoparticles are produced After that solvent
evaporation takes place below PIT. Main advantage of this method is that organic solvent is
lost there is no other interest to change the Phase Inversion Temperature.[17]
Super critical fluid method
To prepare biodegradable micro- and nanoparticles the supercritical fluid technology has
been used, because they are environmentally safe. Supercritical CO2 (SC CO2) is the most
widely used supercritical fluid because of its mild critical conditions nontoxicity,
nonflammability and low price. The most common processing techniques involving
supercritical fluids are supercritical anti solvent (SAS) and rapid expansion of critical
solution (RESS). The liquid solvent is employed in the process of SAS, eg: methanol, which
is completely miscible with the supercritical fluid (SC CO2), to dissolve the solute to be
micronized; at the process conditions, the solute is insoluble in the supercritical fluid, the
instantaneous precipitation of the solute is formed due to the extract of the liquid solvent by
the super critical fluid, resulting for the formation of nanoparticles. RESS differs from the
SAS process in that its solute is dissolved in a supercritical fluid and then the solution is
rapidly expanded through a small nozzle into a region lower pressure, Thus the solvent power
Page 7
www.wjpps.com Vol 8, Issue 12, 2019.
298
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
of supercritical fluids dramatically decreases and the solute eventually precipitates. the
precipitate in this technique is basically solvent free.. Supercritical fluid technology
technique, is environmentally friendly and suitable for mass production, requires specially
designed equipment and it is more expensive.[18]
Salting out: Salting out is a modified formulation of emulsion process in fabricating polymer
encapsulated lipophilic drug via salting-out agent. In this preparation, polymer and drug are
dissolved in water soluble solvent such as acetone, ethanol, and methanol whereas aqueous
medium contains gel with stabilizer and high concentration of salting-out agent. The common
choices of salting-out agents used in electrolytes are magnesium chloride, calcium chloride as
well as magnesium acetate. In a nonelectrolyte system, sucrose is utilized. Polymer and drug
are emulsified in aqueous gel forming oil-in-water emulsion under high mechanical stirring.
Subsequently, the emulsion is diluted in adequate volume of water to enrich the diffusion of
solvent into aqueous phase, decreasing the ionic strength in the electrolyte. This step induced
hardened polymers. The solvent is then removed via reduced pressure, followed by
ultracentrifugation and repeated washing to eliminate both salting-out agent and stabilizer to
yield NPs.
The main distinction from the conventional emulsion diffusion method is the presence of
solvent diffusion step due to the presence of salting agent. In this process, salting-out agents
play prominent role in manufacturing polymer encapsulated drugs NPs. The salts initially
impede the miscibility of organic phase into aqueous solution, forming emulsion.
Subsequently, reverse salting-out effect leads to precipitation, which aided in entrapment of
drug into the polymer matrix, forming the NPs. Thus, the advantages of employing this
technique are high yield, excellent efficiency of drug encapsulation, small particle size, and
feasible production scaling up. Moreover, an increase of temperature is not needed
consequently may be useful when heat sensitive substances have to be processes.[19]
Spray drying: spray dryers refer to using spray drying to create particles in the nanometer
range. Spray drying is a gentle method for producing powders with a defined particle size out
of solutions, dispersions, and emulsions which is widely used for pharmaceuticals, food,
biotechnology, and other industrial materials synthesis.
In the past, the limitations of spray drying were the particle size (minimum 2micrometres),
the yield (maximum around 70%), and the sample volume (minimum 50ml for devices in lab
Page 8
www.wjpps.com Vol 8, Issue 12, 2019.
299
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
scale). Recently, minimum particle sizes have been reduced to 300nm, yields up to 90% are
possible, and the sample amount can be as small as 1 ml. These expanded limits are possible
due to new technological developments to the spray head, the heating system, and the
electrostatic particle collector. To emphasize the small particle sizes possible with this new
technology, it has been described as "nano" spray drying. However, the smallest particles
produced are in the sub-micrometric range common to fine particles rather than the
nanometer scale of ultrafine particles.[20]
Polymerization method
In this method, nanoparticles are formed in an aqueous solution, due to polymerization of
monomers. Dissolving in the polymerization medium or by adsorption onto the nanoparticles
drug is in-corparated after polymerization completed. The nanoparticle suspension is then
purified to remove various stabilizers and surfactants employed for polymerization by
ultracentrifugation and re-suspending the particles in an isotonic surfactant-free medium.
This technique has been reported for making polybutyl cyanoacrylate or poly
(alkylcyanoacrylate) nanoparticles.[21]
Emulsification method
Another method which can be used for preparation of nanoparticles is the emulsification
diffusion method. The method utilizes a partially water-soluble solvent like acetone or
propylene carbonate. The polymer and the drug are dissolved in the solvent and it is
emulsified in the aqueous phase containing the stabilizer. The role of stabilizer prevents the
aggregation of emulsion droplets by adsorbing of the surface of the droplets. Addition of
water to the emulsion, allow the diffusion of the solvent into the water. The solution is stirred
leading to the nano precipitation of the particles. Further, it can be collected by
centrifugation, or the solvent can be removed effectively by dialysis. The main problem with
this method is that the water soluble drugs tend to leak out from the polymer phase during
diffusion steps. So, in order to avoid this problem the dispersing medium changed from
aqueous medium to medium chain triglycerides and a small amount of surfactant is added
into it. The Nano particles are collected from the oily suspension by centrifugation.[22]
Evaluation of Nanoparticles
Particle size
Particle size and size distribution are the most important characteristics of nanoparticle
systems. They determine the in vivo distribution, biological fate, toxicity and the targeting
Page 9
www.wjpps.com Vol 8, Issue 12, 2019.
300
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
ability of nanoparticle systems. In addition, they can also influence the drug loading, drug
release and stability of nanoparticles. Many studies have demonstrated that nanoparticles of
sub-micron size have a number of advantages over microparticles as a drug delivery
system.[23]
Generally nanoparticles have relatively higher intracellular uptake compared to
microparticles and available to a wider range of biological targets due to their small size and
relative mobility. Desai et al found that 100nm nanoparticles had a 2.5fold greater uptake
than 1µm microparticles, and 6 fold greater uptake than 10µm microparticles in a Caco-2 cell
line.[24]
In a subsequent study[25]
, the nanoparticles penetrated throughout the submucosal
layers in a rat in situ intestinal loop model, while micro particles were predominantly
localized in the epithelial lining. It was also reported that nanoparticles can across the blood-
brain barrier following the opening of tight junctions by hyper osmotic mannitol, which may
provide sustained delivery of therapeutic agents for difficult-to-treat diseases like brain
tumors.[26]
Tween 80 coated nanoparticles have been shown to cross the blood-brain
barrier.[27]
In some cell lines, only submicron nanoparticles can be taken up efficiently but not
the larger size micro particles.[28]
Drug release is affected by particle size. Smaller particles have larger surface area, therefore,
most of the drug associated would be at or near the particle surface, leading to fast drug
release. Whereas, larger particles have large cores which allow more drug to be encapsulated
and slowly, diffuse out.[29]
Smaller particles also have greater risk of aggregation of particles
during storage and transportation of nanoparticle dispersion. It is always a challenge to
formulate nanoparticles with the smallest size possible but maximum stability.
Polymer degradation can also be affected by the particle size. For instance, the rate of PLGA
polymer degradation was found to increase with increasing particle size in vitro.[30]
It was
thought that in smaller particles, degradation products of PLGA formed can diffuse out of the
particles easily while in large particles, degradation products are more likely remained within
the polymer matrix for a longer period to cause autocatalytic degradation of the polymer
material. Therefore, it was hypothesized that larger particles will contribute to faster polymer
degradation as well as the drug release. However, Panyam et al prepared PLGA particles with
different size ranges and found that the polymer degradation rates in vitro were not
substantially different for different size particles.[31]
Currently, the fastest and most routine method of determining particle size is by photon-
correlation spectroscopy or dynamic light scattering. Photon-correlation spectroscopy
Page 10
www.wjpps.com Vol 8, Issue 12, 2019.
301
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
requires the viscosity of the medium to be known and determines the diameter of the particle
by Brownian motion and light scattering properties.[32]
The results obtained by photon-
correlation spectroscopy are usually verified by scanning or transmission electron microscopy
(SEM or TEM).
Drug Entrapmaent Efficiency
The nanoparticles were separated from the aqueous medium by ultracentrifugation at 10,000
rpm for 30 min at 50C. Then the resulting supernatant solution was decanted and dispersed
into phosphatebuffer saline pH 7.4. Thus the procedure was repeated twice to remove the
unentrapped drug molecules completely. The amount of drug entrapped in the nanoparticles
was determined as the difference between the total amount of drug used to prepare the
nanoparticles and the amount of drug present in the aqueous medium. Drug Entrapment
efficiency (%) = Amount of released from the lysed nanoparticle X 100 Amount of drug
Initially taken to prepare the Nanoparticles.[33]
Zeta potential
The Zeta potential of a nanoparticle is commonly used to characterized the surface charge
property of nanoparticles. It reflects the electrical potential of particles and is influenced by
the composition of the particle and the medium in which it is dispersed. Nanoparticles with a
zeta potential above (±) 30 mV have been shown to be stable in suspension, as the surface
charge prevents aggregation of the particles.[34]
SEM analysis
Further characterization was done by Scanning Electron Microscope (SEM). The diameter of
the Silver nano particles was determined. A scanning electron microscope (SEM) is a type of
electron microscope that images a sample by scanning it with a beam of electrons in a raster
scan pattern. The electrons interact with the atoms that make up the sample producing signals
that contain information about the sample's surface topography, composition, and other
properties such as electrical conductivity.[35]
Compatibility Studies: Compatibility in drug and polymer is the main issue in the
formulation. The drug should be compatible with polymers which are being used. The
compatibility of drug with adjuvants can be determined by Thin Layer Chromatography
(TLC) and Fourier Transform Infra-red Spectroscopy (FT-IR).[36]
Page 11
www.wjpps.com Vol 8, Issue 12, 2019.
302
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
Resiliency: To determine the viscoelastic properties of nanoparticle. Viscoelastic properties
of particle is modified to produce beedlets which are softer and firmer when needed for final
formulation. When cross linking got increased and tends to slow down rate of release.
Resiliency are studied according to requirement by releasing function of cross-linking with
time.[37]
Dissolution tests : Dissolution profile of nanoparticle are studied using dissolution apparatus
USP having a modified basket consist of 5ml stainless steel mesh with a speed of rotation
around 150rpm. Proper dissolution medium is selected and solubility of active contents are
considered to ensure sink conditions. Proper analytical method are used for the sample form
dissolution medium(38)
Particle Shape
The nanoparticles were subjected to microscopic examination (SEM) for characterization
size. The nanosuspension was characterized by SEM before going for evaluation; the
nanosuspension was lyophilized to form solid particles. The solid particles were coated with
platinum alloy using a sputter coater.[38]
Limitations of Nanoparticles
1. Small size and large surface area can lead to particleparticle aggregation, making physical
handling of nanoparticles difficult in liquid and dry forms.
2. In addition, small particles size and large surface area readily result in limited drug
loading and burst release. These practical problems have to be overcome before
nanoparticles can be used clinically or made commercially available.[39.40]
Applications of Nano particle
Cancer therapy
Photodynamic cancer therapy is based on the destruction of the cancer cells by laser
generated atomic oxygen, which is cytotoxic. A greater quantity of a special dye that is used
to generate the atomic oxygen is taken in by the cancer cells when compared with a healthy
tissue. Hence, only the cancer cells are destroyed then exposed to a laser radiation.
Unfortunately, the remaining dye molecules migrate to the skin and the eyes and make the
patient very sensitive to the daylight exposure. This effect can last for up to six weeks.
Page 12
www.wjpps.com Vol 8, Issue 12, 2019.
303
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
To avoid this side effect, the hydrophobic version of the dye molecule was enclosed inside a
porous nanoparticle.[41]
The dye stayed trapped inside the Ormosil nanoparticle and did not
spread to the other parts of the body. At the same time, its oxygen generating ability has not
been affected and the pore size of about 1 nm freely allowed for the oxygen to diffuse out.
Protein detection
Proteins are the important part of the cell's language, machinery and structure, and
understanding their functionalities is extremely important for further progress in human
wellbeing. Gold nanoparticles are widely used in immunohistochemistry to identify protein-
protein interaction. However, the multiple simultaneous detection capabilities of this
technique are fairly limited. Surface-enhanced Raman scattering spectroscopy is a well-
established technique for detection and identification of single dye molecules. By combining
both methods in a single nanoparticle probe one can drastically improve the multiplexing
capabilities of protein probes. The group of Prof. Mirkin has designed a sophisticated
multifunctional probe that is built around a 13nm gold nanoparticle. The nanoparticles are
coated with hydrophilic oligonucleotides containing a Raman dye at one end and terminally
capped with a small molecule recognition element (e.g. biotin). Moreover, this molecule is
catalytically active and will be coated with silver in the solution of Ag (I) and hydroquinone.
After the probe is attached to a small molecule or an antigen it is designed to detect, the
substrate is exposed to silver and hydroquinone solution. A silver-plating is happening close
to the Raman dye, which allows for dye signature detection with a standard Raman
microscope. Apart from being able to recognise small molecules this probe can be modified
to contain antibodies on the surface to recognise proteins. When tested in the protein array
format against both small molecules and proteins, the probe has shown no cross-reactivity.[42]
Tissue Engineering
The natural bone surface in most cases contains features that are approximately 100nm
across. If an artificial bone implant‟s surface is smooth, the body will reject it. By creating
nano-sized features on the surface of the knee or hip prosthesis, the chances of rejection can
be reduced. The production of osteoblasts can also be simulated, this was demonstrated using
ceramic, polymeric, and recently, metal materials. These findings could help to design a
robust and long-lasting hip or knee replacements and reduce the chances of the implant
becoming loose.[42]
Page 13
www.wjpps.com Vol 8, Issue 12, 2019.
304
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
Energy and Electronics
Researchers are exploring the use of nanotechnology to generate more efficient and cost-
effective energy. When sunlight is concentrated on nanoparticles, it creates steam with high
energy efficiency.
Similarly, high-efficiency light bulbs can be produced with a nano-engineered polymer
matrix in a specific style. These innovative bulbs are shatterproof and have double the
efficiency of fluorescence light bulbs.
Attempts are also being made to develop high-efficiency LEDs using arrays of nano-sized
structures known as plasmonic cavities. Similarly, windmill blades are being developed using
epoxy containing carbon nanotubes. These nanotube-filled epoxies help to create stronger yet
lightweight blades, which boost the amount of electricity produced by individual windmills.
Nanotube sheets have also been used to create thermocells, which produce electricity when
the cell sides are at varying temperatures. These nanotube sheets can be enclosed around a
car‟s exhaust pipe to produce electricity from heat which is otherwise wasted.
Nanotechnology is employed in many different electronics, communications, and computing
applications, providing smaller, faster, and more portable systems. These systems can store
large amounts of data.
Some examples of nanoelectronics are cell phone castings, flash memory chips for iPod
nano's, antibacterial and antimicrobial coatings on keyboard and mouse, etc. Nanotechnology
is used in smart cards, printed electronics for RFID, and smart packaging, as well as in
flexible displays for e-book readers and life-like video games.
It is even used in nanoscale transistors that are more powerful, faster, and highly energy-
efficient. In the future, the entire memory of a computer may be stored on a just one small
chip.
Other uses of nanotechnology include next-generation televisions, plasma displays, digital
cameras, laptops, quantum computers, magnetic random access memory, and organic light-
emitting diodes (OLEDs). Nanotechnology is set to redefine many electronic products,
processes, and applications in future.[43]
Page 14
www.wjpps.com Vol 8, Issue 12, 2019.
305
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
REFERENCES
1. Langer R. Biomaterials In Drug Delivery And Tissue Engineering: One Laboratory's
Experience. Acc Chem Res 2000; 33: 94-101.
2. Bhadra D, Bhadra S, Jain P, Jain Nk. Pegnology: A Review of Peg-Ylated Systems.
Pharmazie, 2002; 57: 5-29.
3. Kommareddy S, Tiwari Sb, Amiji Mm. Long-Circulating Polymeric Nanovectors For
Tumor-Selective Gene Delivery. Technol Cancer Res Treat, 2005; 4: 615-25. Akl M.
Awwad, Nidà M. Salem Nanoscience and Nanotechnology, 2012; 2(4): 125-128.
4. Lee M, Kim Sw. Polyethylene Glycol-Conjugated Copolymers For Plasmid Dna
Delivery. Pharm Res, 2005; 22: 1-10.
5. Nanogloss.Com/Nanotechnology/Advantages-And-Disadvantages-Of-
Nanotechnology/#Axzz5qnyn7a3b
6. Https://Smallbusiness.Chron.Com/Advantages-Disadvantages-Nanotechnology-
37398.Html
7. Vj Mohanraj and Y Chen2, Nanoparticles, Tropical Journal Of Pharmaceutical Research,
June, 2006; 5(1): 561-573.
8. Euyjin Lee, Longhai Piao, And Jinkwon Kim Synthesis Of Silver Nanoparticles From
The Decomposition Of Silver (I) [Bis(Alkylthio)Methylene] Malonate Complexes Bull.
Korean Chem. Soc, 2012; 33.
9. Nisha, Neeraj Singh, Ashish Singla, Neelam, Sukhbir Singh And Aastha Sharma,
Nanoparticles, International Journal Of Pharmaceutical And Chemical Sciences; Issn:
2277; 5005.
10. Shalu Shukla, A Review Article On Nanoparticle, Institute Of Good Manufacturing
Practices India.
11. Vj Mohanraj1 And Y Chen2, Nanoparticles, Tropical Journal Of Pharmaceutical
Research, June, 2006; 5(1): 561-573.
12. Basavaraj Udapudi, Praveenkumar Naik, Sabiha Tabassum Savadatti, Rupali Sharma,
Samprita Balgi Synthesis And Characterization Of Silver Nanoparticles International
Journal Of Pharmacy And Biological Science. Ijpbs, 2012; 2(3): 10-14.
13. Euyjin Lee, Longhai Piao,And Jinkwon Kim Synthesis Of Silver Nanoparticles From The
Decomposition Of Silver(I) [Bis(Alkylthio)Methylene]Malonate Complexes Bull. Korean
Chem. Soc, 2012; 33.
Page 15
www.wjpps.com Vol 8, Issue 12, 2019.
306
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
14. Aarti P. Nikam, Mukesh. P. Ratnaparkhiand, Shilpa P. Chaudhari, Nanoparticles,
International Journal of Research and Development In Pharmacy And Life Sciences,
August - September, 2014; 3(5): 1121-1127.
15. Vj Mohanraj1 And Y Chen 2, Nanoparticles, Tropical Journal Of Pharmaceutical
Research, June, 2006; 5(1): 561-573.(2)
16. Https://Www.Bing.Com/Images/Search?View=Detailv2&Ccid=3q29yt1a&Id=D47a454a
65a47d0f23e0e2009b2358247b780599&Thid=Oip.3q29yt1a259hzscs2.
17. Aarti P. Nikam, Mukesh. P. Ratnaparkhiand, Shilpa P. Chaudhari, Nanoparticles,
International Journal of Research and Development In Pharmacy And Life Sciences,
August - September, 2014; 3(5): 1121-1127.
18. Aarti P. Nikam, Mukesh. P. Ratnaparkhiand, Shilpa P. Chaudhari, Nanoparticles,
International Journal of Research and Development In Pharmacy And Life Sciences,
August - September, 2014; 3(5): 1121-1127.
19. Keemilimzuratul A.A.Hamid, Polymer Nanoparticle Carriers In Drug Delivery Systems,
Applications Of Nanocomposite Materials In Drug Delivery, 2018; 217-237.
20. Https://En.Wikipedia.Org/Wiki/Nano_Spray_Dryer.
21. Puglisi G, Fresta M, Giammona G, Ventura Ca. Influence Of The Preparation Conditions
On Poly(Ethylcyanoacrylate) Nanocapsule Formation. Int. J. Pharm, 1995; 125: 283-287.
22. Kwon H-Y.,Preparation Of Plga Nanoparticles Containing Estrogen By Emulsification–
Diffusion Method, Colloids Surf. Release, 2001; 182: 123–30.
23. Panyam J, Labhasetwar V. Biodegradable Nanoparticles for Drug And Gene Delivery To
Cells And Tissue. Adv Drug Deliv Rev, 2003; 55: 329-47.
24. Desai Mp, Labhasetwar V, Walter E, Levy Rj, Amidon G L, The Mechanism Of Uptake
Of Biodegradable Microparticles In Caco-2 Cells Is Size Dependent. Pharm Res, 1997;
14: 1568-73.
25. Desai Mp, Labhasetwar V, Amidon Gl, Levy Rj. Gastrointestinal Uptake of
Biodegradable Microparticles: Effect Of Particle Size. Pharm Res, 1996; 13: 1838-45.
26. Kroll Ra, Pagel Ma, Muldoon Ll, Roman-Goldstein S, Fiamengo Sa, Neuwelt Ea.
Improving Drug Delivery To Intracerebral Tumor And Surrounding Brain In A Rodent
Model: A Comparison Of Osmotic Versus Bradykinin Modification Of The Blood-Brain
And/Or Blood-Tumor Barriers. Neurosurgery, 1998; 43: 879-86; Discussion 886-9.
27. Kreuter J, Ramge P, Petrov V, Hamm S, Gelperina Se, Engelhardt B, Alyautdin R, Von
Briesen H, Begley Dj. Direct Evidence That Polysorbate-80-Coated Poly
Page 16
www.wjpps.com Vol 8, Issue 12, 2019.
307
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
(Butylcyanoacrylate) Nanoparticles Deliver Drugs To The Cns Via Specific Mechanisms
Requiring Prior Binding Of Drug To The Nanoparticles. Pharm Res, 2003; 20: 409-16.
28. Zauner W, Farrow Na, Haines Am. In Vitro Uptake Of Polystyrene Microspheres: Effect
Of Particle Size, Cell Line And Cell Density. J Control Release, 2001; 71: 39-51.
29. Redhead Hm, Davis Ss, Illum L. Drug Delivery In Poly (Lactide-Co-Glycolide)
Nanoparticles Surface Modified With Poloxamer 407 And Poloxamine 908: In Vitro
Characterisation And In Vivo Evaluation. J Control Release, 2001; 70: 353-363.
30. 30. Dunne M, Corrigan Oi, Ramtoola Z. Influence of Particle Size And Dissolution
Conditions On The Degradation Properties Of Polylactide-Co-Glycolide Particles.
Biomaterials, 2000; 21: 1659-1668.
31. Panyam J, Dali Mm, Sahoo S K, Ma W, Chakravarthi Ss, Amidon Gl, Levy Rj,
Labhasetwar V. Polymer Degradation And In Vitro Release Of A Model Protein From
Poly (,-Lactide-Co-Glycolide) Nano- And Microparticles. J Control Release, 2003; 92:
173-187.
32. Swarbrick J, Boylan J. Encyclopedia Of Pharmaceutical Technology. 2nd Ed.; Marcel
Dekker: New York, 2002.
33. Delvecchio Rick. Berkeley Considering Need For Nano Safety.Articles.Sfgate.Com;
2006.
34. Couvreur P, Barratt G, Fattal E, Legrand P, Vanthier C. Nanocapsule Technology; A
Review. Crit Res Ther Drug Carrier Syst, 2002; 19: 99-134.
35. R. Das, S. S. Nath, D. Chakdar, G. Gope, R. Bhattacharjee Preparation Of Silver
Nanoparticles And Their Characterization. Journal of Nanotechnology Online. June,
2009; 17.
36. Tiwari H., Mahor A., Dixit N.D., Kushwaha M., A Review On Nanosponges, World
Journal Of Pharmacy And Pharmaceutical Sciences, 2014; 3: 219-233.
37. Wester R., Patel R., Natch S., Leyden J., Melendres J, Maibach H., Controlled Release Of
Benzoyl Peroxide From A Porous Microsphere Polymeric System Can Reduce Topical
Irritancy, J. Am. Acad. Derm.,1991; 24: 720-726
38. Kreuter J, Ramage Pv, Hamm S, Gelpenia Se, Engeltatdt B And Alyantdin Ryvon
Briesen H. Direct Evidence That Polysorbate-80 Coated Poly (Butylcyanocrylate)
Nanoparticles Deliver Drugs To The Cns Via Specific Mechanisms Required Prior
Binding Of Drug To The Nanoparticles. Phrm Res, 2003; 20: 409-16.
39. Langer R. Biomaterials In Drug Delivery and Tissue Engineering; One Labortory‟s
Experience. Acc Chemres, 2000; 33: 94-101.
Page 17
www.wjpps.com Vol 8, Issue 12, 2019.
308
Divya et al. World Journal of Pharmacy and Pharmaceutical Sciences
40. Bhadia D, Bhadra S, Jain P and Jain Nk. Pegnology; A Review of Pegylated Systems;
Pharmazin, 2002; 57: 520.
41. Roy I, Ohulchanskyy Ty, Pudavar He, Bergey Ej, Oseroff Ar, Morgan J, Dougherty Tj,
Prasad Pn. Ceramic-Based Nanoparticles Entrapping Water-Insoluble Photosensitizing
Anticancer Drugs: A Novel Drug-Carrier System for Photodynamic Therapy. J Am Chem
Soc, 2003; 125: 7860–7865. Doi: 10.1021/Ja0343095.
42. Cao Yc, Jin R, Nam Jm, Thaxton Cs, Mirkin Ca. Raman Dye-Labeled Nanoparticle
Probes for Proteins. Jacs, 2003; 125: 14676–14677. Doi: 10.1021/Ja0366235.
43. Azonano, Nanoparticle Suppliers and Applications, 2016; 30.