The Three Stooges® is a registered trademark of C3 Entertainment, Inc. The Three Stooges® characters, names, and all related indicia are trademarks of C3 Entertainment, Inc. ©2012 C3 Entertainment, Inc. All Rights Reserved. www.threestooges.com Ford Motor Company Trademarks and Trade Dress used under license to Round 2, LLC. Goodyear (and wing foot design) and Eagle are trademarks of The Goodyear Tire & Rubber Company, Akron, Ohio USA used under license by Round 2, LLC. AMT and Round 2 and design are trademarks of Round 2, LLC. ©2012 Round 2, LLC, South Bend, IN 46628 USA. Product and packaging designed in the USA. Made in China. All rights reserved. 5. FINAL CHASSIS ASSEMBLY 7. FINAL ASSEMBLY STOCK/CUSTOM/STREET A. STOCK B. CUSTOM C. STREET METAL AXLES ASSEMBLED REAR WHEELS ASSEMBLED FRONT WHEELS WINDOW (Clear) BODY ASSEMBLY HEADLIGHT LENSES (Clear) 56 REAR DOOR (May be glued open or closed) ASSEMBLED INTERIOR 321 WINDSHIELD PILLAR (C) 313 HEADLIGHT BEZEL (C) 313 HEADLIGHT BEZEL (C) 37 BATTERY 308 REAR DOOR HANDLE (C) 300 TAILLIGHT (C) 300 TAILLIGHT (C) OPEN HOLE (Stock only) OPEN HOLE (Custom only) (both sides) OPEN HOLE (Custom only) ASSEMBLED CHASSIS FENDERS/RUNNING BOARDS 38 or 44 LICENSE PLATE BRACKET 401 REAR WINDOW (Clear) BODY 40 HOOD 40 HOOD 40 HOOD 54 GAS FILLER NECK (C 307 ANTENNA (C) 317 ANTENNA (C) 325 SPOTLIGHT (C) 325 SPOTLIGHT (C) 316 GAS CAP (C) 54 GAS FILLER NECK (C 316 GAS CAP (C) 316 GAS CAP (C) 43 or 39 LICENSE PLATE BRACKET 43 or 39 LICENSE PLATE BRACKET REMOVE 301 GRILLE (C) 301 GRILLE (C) 21 GRILLE COVER (Non-Plated) 21 GRILLE COVER 312 REAR BUMPER (C) 352 REAR BUMPER (C) 324 FRONT BUMPER (C) 351 FRONT BUMPER (C) ASSEMBLED CHASSIS ASSEMBLED CHASSIS ASSEMBLED CHASSIS ASSEMBLED BODY ASSEMBLED BODY ASSEMBLED BODY OR 6. BODY ASSEMBLY STOCK/CUSTOM/STREET TRIM OFF CROSSMEMBER NOTE: Front & rear bumpers can be omitted as shown if desired. A791-200 READ THIS BEFORE YOU BEGIN 1940 FORD SEDAN DELIVERY Assembly: Carefully study and understand the entire instruction sheet. Compare the parts in the box to the instruction sheet to be sure you have received all the parts required. Carefully remove parts from trees. Before cementing, "TEST FIT" parts together to insure proper location and alignment. Scrape paint and plating from surfaces to be cemented. Subassemblies and components should be painted before any parts are attached. Use only cement and paint made for styrene plastic. Painting: Wash parts thoroughly with mild soap and water. Parting lines, glue joints, and sharp edges should be sanded or filled with filler putty designed for plastic. Apply a "primer" coat and allow to dry. Check parts for imperfections and repeat the procedure if necessary. Remove any lint or dust. Apply paint evenly, in several thin coats rather than one heavy coat. Allow each coat to thoroughly dry before the next is applied. Each coat should be carefully “wet sanded” using slightly damp No. 1200 sandpaper. Be careful not to remove any detail white sanding. Lightest colors should be painted first. Use frosted tape to mask off areas not to be painted. Remove tape after paint is dry to the touch. Use a very fine brush to touch up edges. Decals: See back of decal sheet sheet for proper application. Decals should to be added after applying a gloss coat. Apply a final clear coat after decals are dry. NOTE: (C) indicates "chrome" parts. TRIM OFF FOR STOCK VERSION 1/25 SCALE MODEL KIT