aluminum & steel POLEs (Revision 1)
aluminum & steel
POLEs(Revision 1)
11
Poles from Sterner Lighting consistently deliverhigh quality, performance and value. Just theright look can accompany any luminaire withoutsacrificing performance or durability.
Sterner provides seven types of steel andaluminum poles, giving you many ways to combineindustry-leading performance with eye-catchingbeauty and appeal.
Using the latest advances in materials, powder coatingand anodizing, Sterner combines optimal functionalitywith aesthetic appeal. And you can count on Sterner tostand behind its products long after installation.
Poles from Sterner Lighting offer three essential capabilities:
• Single-seam welding between base plate and poleincreases strength and durability.
• Fully galvanized anchor bolts are supplied with a boltcircle template, both of which are available for advancedshipment to make installation easier.
• A long lasting durable finish is achieved with a multistagewashing process followed by a powder coat, anodized orpolyurethane finish.
Our products are designed to be easy to install and requireminimum maintenance. Their rugged construction keeps Sterner products looking and performing their best throughdecades of use.
The poles identified within this brochure constitute our standardoffering. Please consult the factory for additional pole sizes.
table of contentsour aluminum advantage . . . . . . . . . . . . . . . . . . . . . . . . .2aLUMINUM POLE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .3ROUND TAPERED ALUMINUM (RTA) . . . . . . . . . . . . . . . . . . . .4ROUND STRAight aluminum (RSA) . . . . . . . . . . . . . . . . . . .5square straight aluminum (SSA) . . . . . . . . . . . . . . . . . . .6steel pole specifications . . . . . . . . . . . . . . . . . . . . . . . . . .7round straight steel (rss) . . . . . . . . . . . . . . . . . . . . . . . .8round tapered steel (rts) . . . . . . . . . . . . . . . . . . . . . . . . .9square straight steel (sss) . . . . . . . . . . . . . . . . . . . . . . . .10square tapered steel (sts) . . . . . . . . . . . . . . . . . . . . . . . . .11pole option details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12wind map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13fixture epa's . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
POLES
2
our aluminum advantage Pole shaft
Internal aluminumsleeve
Flush hand hole
Base
flush hand hole coversand internal Sleeving
We supply all of our non-hinged base aluminum poles with a flush handhole cover. We are able to do this because we internally sleeve the inside ofthe pole a minimum of 18" (L-base requires standard hand hole, and is notinternally sleeved). This provides the mounting area for the flush handhole, while increasing the overall strength of the base of our poles at thesame time. The end result is a clean finish detail that eliminates unsightlyweld marks or external covers.(Additional sleeve lengths are available to increase EPA ratings, contact factory for specificordering information.)
Recessed & Surface Hinge Base Poles
For ease of installation and service, use our surface or recessed hingebases on aluminum poles (20' or less). Eliminate ladders or lifttrucks by hinging the pole to the ground saving you time andmoney. Choose our unique recessed version to eliminateunattractive and obstructive base covers for streetscapeapplications. Please consult our factory for application andordering information.(No sleeve or hand hole required, all wiring is done in the base.)
Patented Break-AwayBanner Arms – BN
This patented (patent #4,720,204) device is designed tocollapse the banner arm if winds exceed allowable speeds,thus preventing the pole from reaching its maximumstress point. A stainless steel safety cable extends throughthe entire length of the break-away device to prevent thebanner and banner arm from falling to the ground whencollapsed. The break-away banner arm can accept either.75" or 1.25" pipe size banner arms. Please consult thefactory for ordering information.
Anodized Aluminum Poles
Our aluminum poles are available in the samestandard anodized colors as are our extrudedproducts. As we don’t weld additional attachments,our standard flush hand holes allow the final finishand colors to match and be uniform. We provide astylized finish that is durable enough to stand thetest of time or the harshest environments.Anodizing is extremely resistant to flaking,fading, and severe or saltwater environments.Consult our factory for possible extendedfinish warranty information.
Recessed HINGEbase
Break-Away banner arms
Surface hingebase
3
35'
30'
25'
20'
15'
10'
5'
0'
RTA SSARSA
10' - 0"
12' - 6"
15' - 0"
17' - 6"
25' - 0"
20' - 0"
10' - 0"
15' - 0"
24' - 8"
20' - 0"
29' - 8"
12' - 6"
10' - 0"
12' - 6"
15' - 0"
17' - 6"
20' - 0"
25' - 0"
30' - 0"
Aluminum Pole General Specific ations
Pole ShaftThe pole shaft shall be a single piece of seamless extrudedaluminum tube, alloy 6063-T6. Tapered poles are spun-taperedfor additional strength. The rate of taper is 0.10" to 0.20" perfoot, depending on pole size. Shaft shall include an internalaluminum sleeve for additional strength and flush hand hole.(not required for hinge based poles). Sleeve thickness shall be0.1875" to 0.25" and a minimum of 18" in length, depending onpole size.
BaseThe base plate shall be cast aluminum, alloy A356-T6. ‘SSA’ polesare supplied with a two-piece aluminum base cover forattachment after pole is installed. ‘SSA’, ‘RTA’, and ‘RSA’ poles aresupplied with a two-piece aluminum base cover or castaluminum anchor bolt cover for attachment after pole isinstalled, depending on size of pole and base style.(Hinge base poles do not require a base cover.)
Anchor BoltsEach pole shall be supplied with four fully galvanized steelanchor bolts, and eight hex nuts and washers. Bolt circletemplates are included. Advance shipments of anchor bolts andtemplates are available upon request.
Wire AccessWireway access shall be provided via a flush hand hole or hingedbase. Hand holes are 2" x 4" in size for 5" diameter round and 5"square poles and smaller. Hand holes for larger pole cross-sections are 3" x 4" in size. Hand holes are centered 14" or 18"above the base of the pole, depending on size. A flush aluminumhand hole cover is supplied.
Powder Coat & Anodized FinishPoles shall be cleaned using a multistage washing process toremove oil, dirt, and other chemicals from the pole before it isfinished with a standard polyester urethane powder coat paint.Optional anodized finishes are available and shall use anelectrolytic process to oxidize and colorize the aluminum for afinish that is extremely resistant to flaking, fading, and corrosiveenvironments. Standard powder colors are dark bronze, black,white, and natural aluminum. Standard anodized colors arebronze (light, medium, dark), black, and natural aluminum.Custom powder, anodized, and wet finishes are available(contact factory for availability).
*Standard pole heights per style. Additional sizes may be available, contact factory for details.
ALUMINUM POLES*
BK
(7)
0.188(3)
6.0 x 4.5(2)
28
(4)
B
(5) (6)
PRP
(1)
RTA20
(7)
Powder CoatBK Black
BZ Dark Bronze
WH White
AL Natural Aluminum
AnodizedLBZ Light Bronze
MBZ Medium Bronze
DBZ Dark Bronze
ABK Black
AAL Natural Aluminum
NS Non-Standard Finish(consult factory)
DF Duplex Groundfault Receptacle(15 amp, mounted 24" above grade)
PRP Pole Top Photocell Receptacle (arm mount fixtures only)
VD Vibration Dampener(installed through hand hole at pole installation)
BN Break-Away Banner Arm Coupling(can use 0.75" or 1.25" pipe arms)(consult factory for specific ordering info.)
(4)
Pole
Cat
. No.
RTA10
RTA12.5
RTA15
RTA20
RTA20
RTA25
RTA25
RTA30
RTA30
Base
Sty
le
BCR
BCR
BCR
LCR
BCR
L
L
L
L
Con
duit
Ope
ning
D
iam
eter
4.0"4.0"4.5"
4.0"4.0"4.5"
4.0"4.0"4.5"
4.5"4.5"4.5"
5.5"5.5"4.5"
5.5"
5.5"
7.5"
7.5"
80/1
04
15.0
11.0
5.9
7.4
14.2
5.3
7.3
9.4
12.4
100/
130
9.4
6.7
3.4
3.8
8.6
2.6
3.9
5.3
7.3
110/
143
7.6
5.4
2.6
2.8
6.9
2.0
3.0
4.1
5.7
90/1
17
11.7
8.5
4.4
5.2
10.9
3.6
5.2
7.0
9.4
Estim
ated
Shi
ppin
g W
eigh
t
40#
45#
50#
79#
97#
109#
119#
165#
182#
Base
Dim
ensi
on
9.00" Sq. x 3.12"9.00" Sq. x 3.25"11.00" Sq. x 6.5"
9.00" Sq. x 3.12"9.00" Sq. x 3.25"11.00" Sq. x 6.5"
9.00" Sq. x 3.12"9.00" Sq. x 3.25"11.00" Sq. x 6.5"
9.25" Sq. x 3.12" 10.50" x 11.69" x 5.19"
11.00" Sq. x 6.5"
9.62" Sq. x 3.62" 10.50" x 11.69" x 4.5"
11.00" Sq. x 6.5"
10.25" Sq. x 3.25"
10.25" Sq. x 3.25"
11.625" Sq. x 3.88"
11.625" Sq. x 3.88"
Anc
hor
Bolts
0.625" x 16" x 2"0.625" x 16" x 2"0.625" x 16" x 2"
0.625" x 16" x 2"0.625" x 16" x 2"0.625" x 16" x 2"
0.625" x 16" x 2"0.625" x 16" x 2"0.625" x 16" x 2"
0.75" x 16" x 2"0.75" x 16" x 2"
0.625" x 16" x 2"
0.75" x 16" x 2"0.75" x 16" x 2"
0.625" x 16" x 2"
0.75" x 32" x 4"
0.75" x 32" x 4"
1.00" x 36" x 4"
1.00" x 36" x 4"
Bolt
Circ
le
7.00"7.00"7.00"
7.00"7.00"7.00"
7.00"7.00"7.00"
9.19"9.19"7.00"
9.19"9.19"7.00"
9.19"
9.19"
11.50"
11.50"
Anc
hor
Bolt
Proj
ectio
n
2.25"2.25"2.25"
2.25"2.25"2.25"
2.25"2.25"2.25"
3.25"2.25"2.25"
2.50"2.50"2.25"
3.50"
3.50"
4.25"
4.25"
Allowable Pole EPA(steady wind/gusting wind x 1.3)
Wal
l Thi
ckne
ss
0.125"
0.125"
0.125"
0.188"
0.188"
0.156"
0.188"
0.156"
0.188"
Pole
Hei
ght
10' - 0"
12' - 6"
15' - 0"
20' - 0"
20' - 0"
24' - 8"
24' - 8"
29' - 8"
29' - 8"
Dia
met
er
(Tap
ered
)
4.5" x 3.0"
4.5" x 3.0"
4.5" x 3.0"
5.0" x 3.0"
6.0" x 4.5"
6.0" x 4.0"
6.0" x 4.0"
8.0" x 4.5"
8.0" x 4.5"
14"(18" for 25' or higher)
DIAMETER(TAPERED)
See PoleData Table
Below
5,6
5
NOTES: Responsibility lies with the specifier for correct pole selection based on local codes and standards for the job location. (see Wind Map on page 13 for details)
NOTES:1) RTA10,12.5 & 15 are available in 0.125" wall standard.2) RTA20 is available in 0.188" wall standard.3) RTA25 & 30 are available in both 0.156" & 0.188" standard.
4) '10' applies to both arm & yoke mount fixtures.5) See below table for dimensions & bolt info.6) C - Style & R - Style bases available 20' max.
L
4
ORDER EXA MPLE
ORDERING SEQUENCE
POLE DATA
RTA – ROUND TAPERED ALUMINUM POLES
14"
BK
(7)
0.125(3)
4.5(2)
28
(4)
B
(5) (6)
PRP
(1)
RSA20
NOTES: Responsibility lies with the specifier for correct pole selection based on local codes and standards for the job location. (see Wind Map on page 13 for details)
Pole
Cat
. No.
RSA10
RSA12.5
RSA15
RSA17.5
RSA17.5
RSA20
RSA20
RSA25
Base
Sty
le
BCR
BCR
BCR
BCR
LCR
BCR
LCR
B
Con
duit
Ope
ning
D
iam
eter
4.0"4.0"4.5"
4.0"4.0"4.5"
4.0"4.0"4.5"
4.5"4.5"4.5"
5.5"5.5"4.5"
4.0"4.0"4.5"
4.5"4.5"4.5"
5.5"
80/1
04
15.0
11.0
5.8
3.9
8.0
2.4
6.4
9.4
100/
130
9.3
6.7
3.3
2.1
4.7
1.0
3.6
5.5
110/
143
7.6
5.4
2.6
1.5
3.8
0
2.8
4.3
90/1
17
11.7
8.5
4.3
2.8
6.8
1.6
4.8
7.1
Estim
ated
Shi
ppin
g W
eigh
t
40#
45#
50#
55#
75#
60#
85#
135#
Base
Dim
ensi
on
9.00" Sq. x 3.12"9.00" Sq. x 3.25"11.00" Sq. x 6.5"
9.00" Sq. x 3.12"9.00" Sq. x 3.25"11.00" Sq. x 6.5"
9.00" Sq. x 3.12"9.00" Sq. x 3.25"11.00" Sq. x 6.5"
9.00" Sq. x 3.12"9.00" Sq. x 3.25"11.00" Sq. x 6.5"
9.25" Sq. x 3.12" 10.50" x 11.69" x 5.19"
11.00" Sq. x 6.5"
9.00" Sq. x 3.12"9.00" Sq. x 3.25"11.00" Sq. x 6.5"
9.25" Sq. x 3.12" 10.50" x 11.69" x 5.19"
11.00" Sq. x 6.5"
9.62" Sq. x 3.64"
Anc
hor
Bolts
0.625" x 16" x 2"0.625" x 16" x 2"0.625" x 16" x 2"
0.625" x 16" x 2"0.625" x 16" x 2"0.625" x 16" x 2"
0.625" x 16" x 2"0.625" x 16" x 2"0.625" x 16" x 2"
0.625" x 16" x 2"0.625" x 16" x 2"0.625" x 16" x 2"
0.75" x 16" x 2"0.75" x 16" x 2"
0.625" x 16" x 2"
0.625" x 16" x 2"0.625" x 16" x 2"0.625" x 16" x 2"
0.75" x 16" x 2"0.75" x 16" x 2"
0.625" x 16" x 2"
0.75" x 32" x 4"
Bolt
Circ
le
7.00"7.00"7.00"
7.00"7.00"7.00"
7.00"7.00"7.00"
7.00"7.00"7.00"
9.19"9.19"7.00"
7.00"7.00"7.00"
9.19"9.19"7.00"
9.19"
Anc
hor
Bolt
Proj
ectio
n
2.25"2.25"2.25"
2.25"2.25"2.25"
2.25"2.25"2.25"
2.25"2.25"2.25"
3.25"2.25"2.25"
2.25"2.25"2.25"
3.25"2.25"2.25"
2.50"
Allowable Pole EPA(steady wind/gusting wind x 1.3)
Wal
l Thi
ckne
ss
0.125"
0.125"
0.125"
0.125"
0.188"
0.125"
0.188"
0.188"
Pole
Hei
ght
10' - 0"
12' - 6"
15' - 0"
17' - 6"
17' - 6"
20' - 0"
20' - 0"
25' - 0"
Dia
met
er
4.5"
4.5"
4.5"
4.5"
5.0"
4.5"
5.0"
6.0"
(7)
DF Duplex Groundfault Receptacle(15 amp, mounted 24" above grade)
PRP Pole Top Photocell Receptacle (arm mount fixtures only)
VD Vibration Dampener(installed through hand hole at pole installation)
BN Break-Away Banner Arm Coupling(can use 0.75" or 1.25" pipe arms)(consult factory for specific ordering info.)
(4)
DIAMETER
See PoleData Table
Below
Powder CoatBK Black
BZ Dark Bronze
WH White
AL Natural Aluminum
AnodizedLBZ Light Bronze
MBZ Medium Bronze
DBZ Dark Bronze
ABK Black
AAL Natural Aluminum
NS Non-Standard Finish(consult factory) NOTES:
1) RSA10,12.5 & 15 are available in 0.125" wall standard.2) RSA17.5 & 20 are available both 0.125" & 0.188" wall standard.3) RSA25 available only in 0.188" standard.
4) '10' applies to both arm & yoke mount fixtures.5) See below table for dimensions & bolt info.6) C-Style & R-Style bases available 20' max.
5,6
5L
5
ORDER EXA MPLE
ORDERING SEQUENCE
POLE DATA
RSA – ROUND STRAIGHT ALUMINUM POLES
(7)
DF Duplex Groundfault Receptacle(15 amp, mounted 24" above grade)
PRP Pole Top Photocell Receptacle (arm mount fixtures only)
VD Vibration Dampener(installed through hand hole at pole installation)
BN Break-Away Banner Arm Coupling(can use 0.75" or 1.25" pipe arms)(consult factory for specific ordering info.)
(4)
SQUAREDIMENSION
See PoleData Table
Below
14"
NOTES: Responsibility lies with the specifier for correct pole selection based on local codes and standards for the job location. (see Wind Map on page 13 for details) *SSA25 & 30 poles are supplied with 6' of aluminum sleeving.
3
E 4,5
R4,5
K4
Pole
Cat
. No.
SSA10
SSA12.5
SSA15
SSA17.5
SSA20
SSA20
SSA25*
SSA30*
Base
Sty
le
LER
LER
LER
LER
LER
LER
L
Con
duit
Ope
ning
D
iam
eter
3.5"4.0"4.5"
3.5"4.0"4.5"
3.5"4.0"4.5"
3.5"4.0"4.5"
3.5"4.0"4.5"
4.62"5.0"4.5"
4.62"
80/1
04
11.5
8.3
4.9
6.3
4.6
9.3
4.0
100/
130
6.5
4.3
1.9
2.6
1.3
3.9
-
110/
143
5.0
3.1
1.0
1.4
-
2.2
-
90/1
17
8.6
5.9
3.1
4.1
2.6
6.2
1.7
Estim
ated
Shi
ppin
g W
eigh
t
42#
47#
55#
83#
90#
112#
135#
Base
Dim
ensi
on
9.94" Sq. x 2.00"9.75" Sq. x 3"
11.00" Sq. x 6.5"
9.94" Sq. x 2.00"9.75" Sq. x 3"
11.00" Sq. x 6.5"
9.94" Sq. x 2.00"9.75" Sq. x 3"
11.00" Sq. x 6.5"
9.94" Sq. x 2.00"9.75" Sq. x 3"
11.00" Sq. x 6.5"
9.94" Sq. x 2.00"9.75" Sq. x 3"
11.00" Sq. x 6.5"
11.56" Sq. x 2.50"12.25" Sq. x 4"
11.00" Sq. x 6.5"
11.56" Sq. x 2.50"
Anc
hor
Bolts
0.75" x 16" x 2"0.625" x 16" x 2"0.625" x 16" x 2"
0.75" x 16" x 2"0.625" x 16" x 2"0.625" x 16" x 2"
0.75" x 16" x 2"0.625" x 16" x 2"0.625" x 16" x 2"
0.75" x 16" x 2"0.625" x 16" x 2"0.625" x 16" x 2"
0.75" x 16" x 2"0.625" x 16" x 2"0.625" x 16" x 2"
0.75" x 16" x 2"0.75" x 16" x 2"
0.625" x 16" x 2"
0.75" x 32" x 4"
Bolt
Circ
le
9.19"7.00"7.00"
9.19"7.00"7.00"
9.19"7.00"7.00"
9.19"7.00"7.00"
9.19"7.00"7.00"
11.00"9.19"7.00"
11.00"
Anc
hor
Bolt
Proj
ectio
n
2.75"2.75"2.25"
2.75"2.75"2.25"
2.75"2.75"2.25"
2.75"2.75"2.25"
2.75"2.75"2.25"
2.75"2.75"2.25"
2.75"
Allowable Pole EPA(steady wind/gusting wind x 1.3)
Wal
l Thi
ckne
ss
0.125"
0.125"
0.125"
0.188"
0.188"
0.188"
0.188"
Pole
Hei
ght
10' - 0"
12' - 6"
15' - 0"
17' - 6"
20' - 0"
20' - 0"
25' - 0"
Squa
re D
imen
sion
4.0"
4.0"
4.0"
4.0"
4.0"
5.0"
5.0"
Powder CoatBK Black
BZ Dark Bronze
WH White
AL Natural Aluminum
AnodizedLBZ Light Bronze
MBZ Medium Bronze
DBZ Dark Bronze
ABK Black
AAL Natural Aluminum
NS Non-Standard Finish(consult factory)
BK
(7)
0.188(3)
4.0(2)
28
(4)
D
(5) (6)
PRP
(1)
SSA20
NOTES:1) SSA10,12.5 & 15 are available in 0.125" wall standard.2) SSA17.5, 20 & 25 are available in 0.188" wall standard.
3) '10' applies to both arm & yoke mount fixtures.4) See below table for dimensions & bolt info.5) E-Style & R-Style bases available 20' max.
Contact factory for availability
4L
6
ORDER EXA MPLE
ORDERING SEQUENCE
POLE DATA
SSA – SQUARE STRAight ALUMINUM POLES
7
40'
35'
30'
25'
20'
15'
10'
5'
0'
RSS RTS SSS STS
12' - 0"
16' - 0"
20' - 0"
25' - 0"
35' - 0"
39' - 0"
30' - 0" 30' - 0"
10' - 0"
12' - 6"
15' - 0"
25' - 0"
20' - 0"
35' - 0"
39' - 0"
25' - 0"
30' - 0"
20' - 0"
15' - 0"
20' - 0"
25' - 0"
Steel Pole General Specific ations
Pole ShaftThe pole shaft shall be manufactured from a single piece of hot-rolled steel with an invisible single longitudinal weld (on afinished pole). Square pole shall have four soft radius corners. Therate of taper is 0.10" per foot for square poles and 0.14" per foot forround poles.
BaseThe base plate shall be hot-rolled steel attached by twocontinuous welds. A two-piece steel base cover is provided with the fixed base poles allowing for attachment after the pole is installed.
Anchor BoltsEach pole shall be supplied with four fully galvanized steelanchor bolts, and eight hex nuts and washers. Bolt circletemplates are included. Advance shipments of anchor bolts andtemplates are available upon request.
Wire AccessWireway access shall be provided via hand holes. Hand holes are3" x 5" in size for 6.5" diameter round or 6.5" square poles orsmaller. All other hand holes are 4" x 6". Hand holes are centered14" above the base of the pole. A steel hand hole cover is included.
Polyurethane finishPoles shall be cleaned with a solvent to remove grease and oiland sandblasted before it is finished with a standard aliphaticpolyurethane coating. Finish shall be U.V. resistant and capableto withstand continuous exposure to exterior conditions.Standard colors are dark bronze, black, white, and naturalaluminum. Custom powder and wet finishes are available(contact factory for availability).
*Standard pole heights per style. Additional sizes may be available, contact factory for details.
STEEL POLES*
BZ
(7)
0.179(3)
4.5(2)
28
(4)
H
(5) (6)
PRP
(1)
RSS20
11 ga.
7 ga.
7 ga.
4.5"
4.5"
5.0"
NOTES:1) RSS15 is available in 0.120" wall standard.2) RSS20 & 25 are available in 0.179" standard.
3) '10' applies to both arm & yoke mount fixtures.4) See below table for dimensions & bolt info.
5.8
5.6
4.7
(7)
PolyurethaneFinish
BK Black
BZ Dark Bronze
WH White
AL Natural Aluminum
NS Non-Standard Finish(consult factory)
DF Duplex Groundfault Receptacle(15 amp, mounted 24" above grade)
PRP Pole Top Photocell Receptacle (arm mount fixtures only)
BN Break-Away Banner Arm Coupling(can use 0.75" or 1.25" pipe arms)(consult factory for specific ordering info.)
(4)
DIAMETER
See PoleData Table
Below
NOTES: Responsibility lies with the specifier for correct pole selection based on local codes and standards for the job location. (see Wind Map on page 13 for details)
8
ORDER EXA MPLE
ORDERING SEQUENCE
POLE DATA
Rss – ROUND STRAight STEEL POLES
BK
(7)
0.120(3)
5.9 x 3.1(2)
28
(4)
H
(5) (6)
PRP
(1)
RTS20
(7)
PolyurethaneFinish
BK Black
BZ Dark Bronze
WH White
AL Natural Aluminum
NS Non-Standard Finish(consult factory)
DF Duplex Groundfault Receptacle(15 amp, mounted 24" above grade)
PRP Pole Top Photocell Receptacle (arm mount fixtures only)
BN Break-Away Banner Arm Coupling(can use 0.75" or 1.25" pipe arms)(consult factory for specific ordering info.)
(4)
DIAMETER(TAPERED)
See PoleData Table
Below
14"
10.9
8.5
9.2
7.7
6.2
6.3
6.0
11 ga.
11 ga.
11 ga.
11 ga.
11 ga.
11 ga.
11 ga.
NOTES:1) RTS12, 16, 20, 25, 30, 35, & 39 are available in 0.120" wall standard.2) '10' applies to both arm & yoke mount fixtures.3) See below table for dimensions & bolt info.
NOTES: Responsibility lies with the specifier for correct pole selection based on local codes and standards for the job location. (see Wind Map on page 13 for details)
4.6" x 3.0"
5.2" x 3.0"
5.9" x 3.1"
6.5" x 3.0"
6.9" x 3.0"
7.6" x 3.0"
8.4" x 3.0"
9
ORDER EXA MPLE
ORDERING SEQUENCE
POLE DATA
RTs – ROUND TAPERED STEEL POLES
BK(7)
0.120(3)
4.0(2)
28(4)
P(5) (6)
PRP(1)
SSS20
(7)
DF Duplex Groundfault Receptacle(15 amp, mounted 24" above grade)
PRP Pole Top Photocell Receptacle (arm mount fixtures only)
BN Break-Away Banner Arm Coupling(can use 0.75" or 1.25" pipe arms)(consult factory for specific ordering info.)
(4)
SQUAREDIMENSION
See PoleData Table
Below
14"
14.1
10.7
7.9
3.9
1.3
10.6
6.2
PolyurethaneFinish
BK Black
BZ Dark Bronze
WH White
AL Natural Aluminum
NS Non-Standard Finish(consult factory)
NOTES:1) SSS10,12.5,15, 20, & 25 are available in 0.120" wall standard.2) SSS25 is available in both 0.120" & 0.188" wall standard.3) SSS30 available only in 0.188" wall standard.
4) '10' applies to both arm & yoke mount fixtures.5) See below table for dimensions & bolt info.
Squa
re D
imen
sion
4.0"
4.0"
4.0"
4.0"
4.0"
5.0"
5.0"
11 ga.
11 ga.
11 ga.
11 ga.
11 ga.
7 ga.
7 ga.
(see Wind Map on page 13 for details)NOTES: Responsibility lies with the specifier for correct pole selection based on local codes and standards for the job location.
10
SSs – SQUARE STRAIGHT STEEL POLESORDER EXA MPLE
ORDERING SEQUENCE
POLE DATA
STS20
STS25
STS30
STS35
STS39
WH
(7)
0.120(3)
5.5 x 3.75(2)
28
(4)
P
(5) (6)
PRP
(1)
STS20
(7)
DF Duplex Groundfault Receptacle(15 amp, mounted 24" above grade)
PRP Pole Top Photocell Receptacle (arm mount fixtures only)
BN Break-Away Banner Arm Coupling(can use 0.75" or 1.25" pipe arms)(consult factory for specific ordering info.)
(4)
SQUARETAPERED
See PoleData Table
Below
14"
8.0
6.0
4.2
1.1
0
NOTES:1) STS20, 25, 30, 35, 39 are available in 0.120" wall standard.2) '10' applies to both arm & yoke mount fixtures.3) See below table for dimensions & bolt info.
0.120"
0.120"
0.120"
0.120"
0.120"
11 ga.
11 ga.
11 ga.
11 ga.
11 ga.
Squa
re (T
aper
ered
)
5.5" x 3.75"
6.25" x 3.75"
7" x 3.75"
7" x 3.75"
7.75" x 3.75"
PolyurethaneFinish
BK Black
BZ Dark Bronze
WH White
AL Natural Aluminum
NS Non-Standard Finish(consult factory)
NOTES: Responsibility lies with the specifier for correct pole selection based on local codes and standards for the job location. (see Wind Map on page 13 for details)
11
STs – SQUARE TAPERED STEEL POLESORDER EXA MPLE
ORDERING SEQUENCE
POLE DATA
12
pole options detailsaluminum and steel poles
aluminum poles only
Receptacles – DF, PRPSterner provides wet-location-listed power and photocellreceptacles as options for use in our poles. All receptacles areGround Fault Circuit Interrupt systems. Photocell receptaclesmay be installed in the top of the pole to avoid unsightlyattachments to the luminaires.
• DF – Duplex Ground Fault Receptacle(15 amp, mntd. 24" above grade)
• PRP – Photocell Receptacle with shorting cap at top of pole
POLE
Vibration Da mpener – VDSecondary mode vibration can occur when wind currents strikethe pole/luminaire combination from two different directions atthe same time. This commonly occurs when using post-topluminaires on aluminum poles over 25 feet in length, whenpoles are mounted above ground level (bridges, parking decks,etc.) or when environmental/geological features cause a passingwind to be redirected back against the poles. Vibrationdampeners are installed through the hand hole at poleinstallation. Sterner recommends that vibration dampeners beused when any of the following conditions exist.
• Poles are greater than 25' in length with a post-top luminaire installed.
• Poles are installed on a parking ramp.• Poles are installed on a bridge.• Poles are installed at an airport.• Poles are installed in a special wind region (e.g., Hawaii).
concrete
foundation
grout
hand hole
field-installed
vibration dampener
Break-Away Banner Arm – BNSterner’s patented banner arm (patent #4,720,204) is a uniquedesign to protect your pole from extreme weather conditions.Can accept either 0.75" or 1.25" pipe size banner arms. (see pg. 2for further details)
9090
90
70
70
80
80
90
90
100
10080
80 8080
70
70
80
8090
90
90
90
100100
100
100
110
110
100
100110
110
70
70
70
70
70
80
80
80
90
7090
60
6070
100110
110
1001009080
80
7070
90100
100100
110 Mi le s per Hour100 Mi le s per Hour
90 Mi le s per Hour80 Mi le s per Hour70 Mi le s per Hour60 Mi le s per Hour
60
6070
Chart data based oninformation from AASHTO (1994) 50 yearmean recurrence interval.
13
EPA InformationAll aluminum and steel pole EPA’s are calculated by polemanufacturer. It is the responsibility of the specifier forcorrect pole selection based on local codes and standards for the location of the job. Allowable pole EPA for jobsitewind conditions must be equal to or greater than the totalfixture EPA.
General Notes • Chart data based on 50 year mean recurrence
interval (1994).• Hawaii has an 80 mph wind velocity.• Puerto Rico has a 95 mph wind velocity.• Use caution in determining wind velocities in
special wind areas:Areas in mountainous locationsAreas around large bodies of water or open landAreas prone to hurricanes, typhoons,tornadoes, & cyclonesAreas near or adjacent to airportsAreas where abnormal wind conditions are known to exist (natural or man-made)
C aution• Wind speeds and listed EPA’s are for ground mounted
installations only. Installations on structures likebridges or buildings must consider the potential forvibration and height factors. Consult AASHTO forthese standards.
American Association of State Highway andTransportation Officials444 N. Capitol Street, NW, Suite 249Washington, DC 20001(202) 624-5800www.aashto.orgE-mail: [email protected]
• Pole Strength Limited Warranty: Standard andunmodified poles by Sterner installed asrecommended, undamaged by corrosion or lack ofmaintenance, shall withstand steady wind conditionsas defined by each pole’s allowable EPA. Extreme windconditions, installation of poles without luminaires,poles installed with attachments (not properlydesigned with BN option), or poles not properly sizedper the job location shall void the pole’s warranty.
wind map united states
2810 3932 4929
Executive-RT
10.5
6.8
3.5
2.2
1.6
7.0
4.4
3.2
7.0
4.4
3.2
8.2
5.4
3.3
8.2
5.4
3.3 4.2
EXEC-RT32
EXEC-RT25
EXEC-RT21
1.5 3.0 3.0 3.5 3.5 5.0
2.2 4.4 4.4 6.6 6.6 8.8
EXEC-SQ19
EXEC-SQ25
2810 3932 4929
Executive-SQ
7.55.75.73.63.61.8
10.88.18.15.45.42.7
EXEC-SQR19
EXEC-SQR25Executive-SQR
2810 3932 4929
EXEC-QL25
2810 3932 4929
Executive-QL25
9.52.5 5.0 5.0 7.3 7.3
14
standard fixture epa 's
101 CORPORATE DRIVESPARTANBURG, SC 29303TEL 864.599.6000 FAX 864.699.4740www.sternerlighting.com