TECHNİCAL 1 Investigation of Oxygen-Acetylene Flashback Reactions in Welding Hoses Kaynak Hortumlarındaki Oksijen-Asetilen Geri T epmeleri ÖZET: Kaynak sektöründe hakim kaygılardan biri, bir oksijen-asetilen (oksiasetilen) geri tepme tepkisinin bir kaynak hortumunun içine yayılarak oksijen-asetilen parlamasına ve hızlı toplanma basıncından dolayı patlamaya neden olmasıdır. Tanık olunan bir kaynak hortumu yangını hangi şartlar altında kaynak hortumlarının içerisinde patlamaların olacağını ve hangi kaynak hortumlarının bu durum- lara maruz kaldığında patlayacağını gösteren testle sonuçlanmıştır. Bu yazı kaynak hortumu yangını gözlemini, geri tepme tepkilerini oluşturan şartları ve kazanın yeniden yapılması sırasında sıradan kaynak hortumlarının içindeki parlama-patlama geçişinin özellikleri- ni görmek amacıyla ortaya konan analitik çalışmaları bildirmektedir. Bu yazı aynı zamanda geri tepme patlamalarından kaynaklanan hortum yarılmalarına özgün ziksel ve kimyasal kriterleri sunmaktadır. ANAHT AR KELİMELER: P atlama, oksia setilen, kay nak, geri tepm e, forensik ye niden yap ma, ateş tepme si, tutulan ate ş tepmesi. ABSTRACT : A common concern in the wel ding industry is the development of conditions wherein an oxygen-acetylene (i.e. , oxyacetylene) ash - back reaction can propagate into a welding hose causing it to burst due to the rapid localized pressurization associated with an oxy- gen-acetylene deagration-to-detonation transition. The investigation of a recent welding hose re resulted in testing to evaluate the conditions under which detonations could be generated within welding hoses and the conditions in which welding hoses would burstwhen exposed to these events. This paper reports on elements of the welding hose re investigation, the conditions for ashbackreactions to develop, and the analytical work performed during the accident reconstruction to characterize deagration-to-detonation transition within typical weld-ing hoses. This paper also suggests physical and chemical criteria that are characteristic to welding hose ruptures due to ashback detonations. KEYWORDS: detonation, oxyacetylene, welding, ashback, backre, forensic reconstruction, backre, sustained-backre Introduction The authors recently investigated an oxyacetylene weldinghose rupture that led to severe burns to an operatör. The weld- ing hose was being used with a commercial welding torch andmixing attachment equipped with a heating tip. The re devel- oped when the operator was attempting to light the torch af- ter setting both the oxygen and acetylene regulators each to 15 psig. According to his statement he opened the acetylene needle valve on the torch handle to initiate the ow of acetylene and lit the acetylene ow normally at the tip of the torch. He in- dicated that when he started opening the oxygen needle valve Giriş Yazarlar bir operatörün ciddi şekilde yanmasıyla sonuçlanan bir oksiasetilen kaynak hortumu patlamasını araştırmışlardır. Kaynak hortumu ticari bir kaynak torçuyla ve ısıtma uçlu birkarıştırma ekipmanıyla kullanıldığı sırada meydana gelmiştir. Yangın, operatör hem oksijen hem de asetilen regülatörünü 15 psig değerine ayarlayıp torçu yakmaya çalıştığı esnada mey- dana gelmiştir. Kendi ifadesine göre asetilen akışını başlatmak için torç sapının üzerindeki asetilen iğne valni açmış ve asetilen akışını normal olarak torçun ucunda yakmıştır. Torç üz- erindeki oksijen iğne valni açmaya başladığında bir “pop” sesi VICTOR EQUIPMENT COMPANY was founded in 1913 byL. W. Stettner. Stettner , a welder by trade, suffered the loss of one eye from a welding accident and subsequentlyset out to design and build better, safer welding product s. His designs for welding and cutting torches and regulators were quickly accepted and VICTOR Oxy-Acetylene Weld-ing Equipment Company grew rapidly . In the spirit of Stett-ners emphasis on SAFETY, VICTOR engineers did co-write this article. Victor is represented by ÖZENSAN A.Ş. in Turkey. Victor Ekipmanları Şirketi 1913 de L. W. Stettner tarafından kuruldu. Aslen kaynakçı olan Stettner, bir kaynak kazasında bir gözünü kaybetti ve ondan sonra daha güvenli kaynakekipmanları tasarlamak için çalışmalara girdi. Tasarladığı kaynak ve kesme torçları ve gaz regülatörleri kısa zamanda kabul gördü ve Victor Oksi-Asetilen Kaynak Ekipmanları Şirketi süratle büyüdü. Victor mühendisleri bu makaleyiStettner’in vurgulamış olduğu güvenlik ruhu ile kaleme aldılar.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
on the torch he heard a “pop” and the ame when out so he
closed both torch needle valves. He then reopened the acety -
lene needle valve and relit the acetylene ow at the torch tip.
When he started opening the oxygen needle valve the second
time the ame again regressed into the torch tip with a pop and a squealing sound. The acetylene welding hose immediately
ruptured resulting in an open-air acetylene re which severely
burned the operator.
Examination of the welding torch and the ruptured acetylene
hose (Figs. 1 and 2) revealed that the acetylene welding hose
had ruptured approximately 48.3 cm (19 in.) upstream of the
connection to the torch handle. The investigation revealed that
after the hose ruptured, a lancing acetylene-air ame at tached
to the ruptured area of the hose and burned away a segment
of the welding hose extending toward the torch, in the direction
of the acetylene ow. The photograph shown in Fig. 2 depicts
a close-up view of the welding hose near the rupture. A clear distinction was observed between the ruptured portion of the
hose and the segment of hose liner that was burned after the
initial rupture. While this paper will avoid discussing the details
of the forensic reconstruction, the testing that was performed
to evaluate ashback reactions within welding hoses will be
presented and the characteristic elements of the combustion
event will be discussed to better understand welding hose rup-
ture due to an oxy-acetylene ashback
duymuş ve alev çıktığını görmüş, bunun üzerine iki iğne valni
de kapatmıştır. Daha sonra asetilen iğne valni tekrar açmış ve
asetilen akışını torçun ucunda tekrar yakmıştır. Oksijen iğne
valni ikinci kez açmaya başladığında ateş büyük bir gürültüyle
yeniden torç ucundan içeri girmiştir. Asetilen kaynağı hortumuanında yarılarak operatörün ciddi ölçüde yaralanmasına sebep
olan açık asetilen ateşi başlamıştır.
Kaynak hortumunun ve patlayan asetilen hortumunun (Şekil
1 ve 2) incelenmesi sonucunda asetilen kaynağı hortumu-
nun torç sapı bağlantısına doğru yaklaşık 48.3 cm (19 inç)
yarıldığını görülmüştür. Araştırmaya göre hortum yarıldıktan
sonra bir asetilen-hava alevi hortumun yarılmış olan kısmından
başlayarak hortumun torça, asetilen akışının olduğu tarafa
doğru olan kısmını kesmiştir. Şekil 2’de gösterilen fotoğrafta
kaynak hortumunun üzerindeki yarık yakından görülmektedir.
Hortumun yarılmış kısmı ile ilk yarılmadan sonra yanan kısmıarasında gözle görülür bir fark vardır.
Bu yazı forensik yeniden yapmanın detaylarını tartışmaktan
kaçınırken, kaynak hortumları içindeki geri tepme tepkilerini
değerlendirmek için gerçekleştirilen test ve tutuşma olayının
karakteristik özellikleri oksiasetilen geri tepmesi sonucu
oluşan kaynak hortumu yarıklarının daya iyi anlaşılması için
sunulmuştur.
1 Vice President, R&D, Wendell Hull and Associates Inc., 1020
S. Main, Las Cruces, NM 88005.
2 Principal Engineer, Victor Equipment Company, Denton, TX.
3 Test Facility Manager, Wendell Hull and Associates, Inc.,
1020 S. Main, Las Cruces, NM 88005.
4 NASA-WSTF, Laboratories Ofce Deputy Chief, Las Cruces,
NM.
1 Başkan Yardımcısı, R&D, Wendell Hull and Associates INC,
1020 S. Main, Las Cruces, NM 88005.
2. Baş Mühendis, Victor Equipment Company, Denton, TX.
3 Test Tesisi Müdürü, Wendell Hull and Associates INC, 1020
S. Main, Las Cruces, NM 88005.
4 NASA-WSTF,Laboratuar Şef Yardımcısı, Las Cruces, NM.
Şekil 1- Torçun ve kaynak hortumunun fotoğrafı (yarılan yer belirtilmiştir).FIG. 1—Photograph of torch and welding hose (area of hoserupture is indicated).
Investigators often point to an event called a ashback reaction
to explain the failure when a welding hose ruptures in a manner
similar to the one discussed here (Figs. 1 and 2). Flashback isfrequently used to describe a regression of the torch tip ame
into the torch to continue burning at the torch’s gas mixer ele-
ment, also known as sustained-backre. However, ashback
is also used to describe regression of the ame fully through
the torch and into one of the gas supply hoses. Due to these
confusing uses of the term ashback, and the simultaneous
use of other terms such as backre and sustained-backre,
agreement on what is referred to by the various terms is often
difcult.
For the sake of clarity, and as used in this paper, the authors
prefer the denitions provided by Broden et al. [1] since they distinguish clearly between the three types of events that can
develop within oxy-acetylene equipment. These denitions are
provided as follows:
Backre—”A backre implies that the ame burns back into the
torch with a sharp bang (pop). Either the ame is extinguished,
or it is reignited at the nozzle opening.” Graphically, this is il-
lustrated in Fig. 3.
Sustained Backre—”In a sustained backre the ame burns
back into the torch with continued burning in the mixer, often
at the mixing point itself. A sustained backre is characterized by an initial
Arka Plan
Araştırmacılar bir kaynak hortumu burada bahsedilenle
(Şekil 1 ve 2) benzer bir biçimde yarıldığında oluşan hatayı
açıklamak için geri tepme tepkisi denilen bir olaya dikkatçekmektedirler. Tutulan geri tepme olarak da bilinen geri
tepme torçun ucundaki alevin torçun içine girerek torçun
gaz karıştırıcısında yanmaya devam etmesini anlatmak için
kullanılmaktadır. Ancak, geri tepme aynı zamanda alevin
torçtan tamamen içeri girerek gaz tedarik hortumlarının birinin
içine girmesini anlatmak için de kullanılmaktadır. Geri tepme
teriminin bu kafa karıştırıcı kullanımları ve ateş tepmesi ve
tutulan ateş tepmesi gibi diğer terimlerle bir arada kullanılması
yüzünden bu terimlerle neyin anlatıldığına karar vermek
çoğunlukla zordur.
Anlatımın anlaşılabilir olması için bu yazıda yazar oksiasetilenekipman içinde ortaya çıkabilecek bu üç çeşit olayı birbirinden
ayıran Broden et al [1] içinde yer alan tanımları tercih etmiştir.
Bu tanımlar aşağıdaki gibidir:
Ateş tepmesi - “Ateş tepmesi torçun içine keskin bir patlamay-
la (pop) dönen alevi anlatmaktadır. Alev söndürülür ya da no-
zul ucunda yeniden yakılır.” Bu durum Şekil 3’te gösterilmiştir.
Tutulan ateş tepmesi – “Tutulan ateş tepmesinde alev torçtan
içeri girerek karıştırıcının içinde, genelde karışım noktasında
yanmaya devam eder.”
Şekil 2 – İlk yarılmanın ve hortumun devam eden yanığınınyakından görünümü.FIG. 2—Close-up view of the upstream initial rupture and theburning of the hose downstream.
FIG. 4—Graphic illustration of a sustained backre.Şekil 4—Torç tutulan ateş tepmesinin grak çizimi.
FIG. 5—Elements of a ashback reaction.Şekil . 5 – Geri tepme tepkisinin parçaları
• Momentary regression of ame into the torch tip accompanied by a “pop” Alevin “pop” ile torç ucuna anlık geri girmesi
• The ame eiter extinguishes or re-ignites at the tipAlev söner ya da torç ucunda yeniden başlar.
• Regression of ame into torch tip followed by sustained burning in the at the mixing chamber Alevin torçun içine girmesinden sonra karışım noktasında yanmaya devam etmesi.
“Tıslama” ya da “yüksek ses” ile olur.
• Accompanied by a “hissing” or “squealing” sound
“squeal” “yüksek ses”
Low/Depleted
Acetylene Pressure
Düşük/azaltılmış AsetilenBasıncı
Tip Plugged
or Restricted
Uç kapalı yada tıkanmış
“pop”
Oxygen
Oxygen
Oksijen
Oksijen
Ateş tepmesi -
Ters Akış - Reverse ow
Geri Tepme- Flashback
Acetylene
Acetylene
Asetilen
Asetilen
FIG. 3—Graphic illustration of a torch backre.
Tutulan Ateş Tepmesi -
Backre
Sustained Backre
Oxygen Control
Vave OPEN
Oksijen KontrolVal AÇIK
High Oxygen PressureYüksek Oksijen Basıncı
Check Valve Missing or İnoperativeKoruma Val Yok ya da Çalışmıyor
Oxygen Reverse Flow İnto Acetylene Hose
Fire Propagetes Through
Asetilen/Oksijen Karışımından AteşÇıkıyor
Flame Regresses
Into Torch Tip
Alev Torç Ucundan Geri Giriyor Flame Front Accelerates Throung Hose