Alarme Auto Steelmate 888W1

Car alarm system

User's Manual

2

2

3

4

4

4

5

6

7

7

7

7

8

8

8

8

8

9

9

9

9

9

10

10

10

User's Manual

Reasons to choose Steelmate -----------------------

Important notice ------------------------------------------

Brief look at transmitters ------------------------------

About LCD screen ---------------------------------------

Battery indicator ------------------------------------------

Transmitter charging ------------------------------------

System operating-----------------------------------------

Status indication -----------------------------------------

Functions ---------------------------------------------------

1. Arming operation ----------------------------------------

2. Passive arming ------------------------------------------

3. Disarming operation------------------------------------

4. Silent arming/disarming--------------------------------

5. Mute arming----------------------------------------------

6. Car searching (locating)-------------------------------

7. Remote sensor bypass------------------------------

8. Central door lock/unlock (F3/F4/F15/F25) ---

9. Dome light delay-----------------------------------------

10. Remote panic ------------------------------------------

11. Time/ alarm time/W-mode setting -----------------

12. Low battery indicator -------------------------------

13. Trunk release ------------------------------------------

14. Arming without transmitters-------------------------

15. Anti-hijack mode ---------------------------------------

16. Transponder card (optional) ------------------------

17. Valet (service mode)----------------------------------

18. Emergency override ----------------------------------

19. Turbo timer mode (F1, F19, F21)------------------

20. Transmitter operation range indication-----------

21. Rearming automatically------------------------------

22. Ultrasonic sensor (optional)-------------------------

23. Tamper alert---------------------------------------------

24. Personal code setting---------------------------------

24.1. How to enter the personal code------------

24.2. How to change the personal code---------

25. Transmitter and transponder (optional) code

learning --------------------------------------------------

26. System programming --------------------------------

Installation Manual

System programming table ---------------------------

Installation instruction----------------------------------

Door lock wiring diagrams ----------------------------

Optional relay wiring diagrams-----------------------

Hood/trunk pin switch relay wiring diagrams---

Wiring diagram---------------------------------------------

Troubleshooting ------------------------------------------

Warranty -----------------------------------------------------

Steelmate warranty card--------------------------------

11

11

12

12

12

12

12

12

13

13

13

14

16

21

24

25

25

26

27

28

28

1

Contents

2 3

1. Professional manufacturer with German qualitystandards.

2. Complete range of products, you can easilychoose your favorite product.

3. There are agents/distributors in more than 80countries to supply local service.

4. More than 100 engineers in the company, youcan enjoy the latest technology.

5. More than 300 patents.

6. Products have international approvals, highquality guaranteed.

7. Leading manufacturer in automotive industry,ISO9001, ISO/TS16949, ISO14001 andOHSAS18001 certified.

Reasons to choose Steelmate

* Please install the system by an authorizedengineer.

* Keep the product and the transmitters away fromwater.

* It is highly recommended to read this manualcarefully before using this unit.

* This product will help you reduce the possibilityof losing the car by discouraging theft. It is not asubstitute for owner’s vigilance. Please take thevaluables with you when leaving the car.

* When the transmitter’s operating distance isshorter or its indicator light turns dark, pleaserecharge the 2-way LCD transmitter or change thebattery of 1-way transmitter ASAP.

Important notice Brief look at transmitters

Chargingsocket

ArmDisarmPower ON/OFF

Antenna

F button

CH2 button

CH3 button

CH2

Arm

Disarm

CH3

LCD transmitteris OFF.

Press button for about3 seconds till the transmitteris turned on with melody.

The backlight will turn on,the icons will light up.

The LCD transmitter needs to be turned on before the first use, the factory setting is OFF.Turn LCD transmitter ON: press and hold button for 3 seconds till the transmitter is turned on with melody.Turn LCD transmitter OFF: press and hold button for 5 seconds till the transmitter is turned off with a beep.Transmitter will be shut down when the battery is used up. If the transmitter cannot be turned on, pleasecharge it first.

System operation

Button Button functionPress and hold for 2 seconds to arm in mutemode (with siren turned off for one arm cycle)

Button function optional

Lock doors & arm the system

Unlock doors & disarm the system Stop alarm

Press and hold for 2 seconds to activatechannel CH2

Press twice to cancel the turbo timerCH2

then CH2CH3 Press to activate channel CH3

Arm with the 1st-stage of shock sensorbypassed

Press and hold for 2 seconds and thenpress CH2 for mute arm with the first stageof shock sensor bypassed

then CH2 then CH2 Arm with both sensors bypassed Press and hold for 2 seconds and thenpress CH2 twice for mute arm with bothsensors bypassed

CH2 then Silent arming

CH2 then Silent disarming

CH2 + CH3 Press and hold for 2 seconds for panicmode

Press both buttons in armed status for mutearming

+ Press and hold for 2 seconds for anti-hijack mode

+ CH2 Press and hold for 2 seconds for carlocating

Press and hold for 2 seconds twice in 7seconds to cancel passive arming for onecycle

2-way transmitter

F (2-way transmitter) Press and hold for 5 seconds forTime/Alarm time/W-mode setting

F and (2-waytransmitter)

Vibration on/off mode

F and CH3 (2-waytransmitter)

Turn on/off W-mode

CLOCK SETUP: CH2 = Increase, CH3= Decrease, F = Next,Start = Beep with button press, hold F for 1 second = Exit

4 5

About LCD screen Battery indicator

Transmitter charging

Battery is full Battery is low Battery is empty.

The transmitting rangewill be affected whenthe battery is low.

Disarming withdoor unlocked

Arming inmute mode

Parking lightsflashing

Clock alarm Door opened

Transmittervibration

Signal bar Arming modeArming withdoor locked

1st-stage shocksensor bypass

Shock sensorbypass

Hood-opened

Trunk -released

Key Ignition ON Anti-hijack Valet mode

Systembusy

Time/Clockand W-function

W-modeON

The battery status of the LCD transmitter willbe shown on the LCD display.

When the battery indicator is empty, thetransmitter needs to be charged immediately.

Charge the transmitter when the battery is lowaccording to the description below. The transmitter'sbattery can be charged discontinuously.

Insert the charger’s pluginto transmitter’s batterycharging socket.

Insert the charger into thevehicle’s cigarette lighter socket.

6 7

Status indication

LED indicator flashing table1) Fast flashing---passive arming mode

2) Slowly flashing ---armed mode

3) No flash----system disarmed

4) Turn on solid --- valet mode

5) 1 flash ... pause --- the first stage shock sensortriggered

6) 2 flashes ... pause--- the second stage shocksensor triggered

7) 3 flashes ... pause --- trunk/hood triggered, INST1 / INST 2 = INST 1

8) 4 flashes ... pause ---door triggered (door (-) ordoor (+))

9) 1 long flash and 3 short flashes---transponderregistration confirmed

Siren short chirps table1) 1 chirp --- system armed

2) 2 chirps --- system disarmed

3) 3 chirps --- system armed with door or trunkopened.

4) 4 chirps --- warning about system triggered afterdisarming

5) 5 chirps --- car searching/locating

Parking lights flashing table1) 1 flash --- system armed

2) 2 flashes --- system disarmed

3) 3 flashes --- system armed with door, hood ortrunk opened

4) 4 flashes --- warning about system triggeredafter disarming

5) 5 flashes --- car searching

Functions

1. Arming operationTo arm the system, press transmitter button :* The siren will chirp once.* The parking lights will flash once.* The doors will be locked.* The LED will start flashing.The system is armed with engine immobilized. LCDtransmitter will beep once and display as below:

While armed, the system will be triggered if:* The door is opened.* The trunk/hood is opened.* The ignition is turned on.* The shock sensor detects an impact.* An optional sensor is triggered.If triggered by the door or trunk/hood input or ignitionON, the siren will sound and the parking lights willflash for 30 seconds.

If the shock sensor detects a light impact to thevehicle, the system will chirp and the parking lightswill flash 5 times to warn away the potential intruder.A heavy impact will trigger the alarm system or anoptional sensor is disturbed, the siren will chirp andthe parking lights will flash for 30 seconds.

If the door or trunk is not closed properly after armingthe system, the siren will chirp 3 times with theparking lights flashing, and transmitter will beep 3times with door icon flashing.

2. Passive ArmingF23-- set passive arming ON/OFF,F24-- set door lock/unlock in passive arming

When passive arming function is on, after 30 seconds(plus F6 arming delay time), the system will be armedautomatically if the car is parked with all the doorsclosed, the sire will chirp once and the parking lightswill flash once. The LED will flash.Note: opening the door resets the passive arming timer.

When passive arming function is on, press and holdbutton + twice for 2 sec in 7 seconds after thecar is parked with all doors closed, it will cancelpassive arming for one cycle. If anti-hijack is activated,it will also be cancelled for one cycle.

Factory setting: passive arming OFF.Note: if the ignition on or trunk is opened in 30 seconds,the passive arming will be cancelled for one cycle.

3. Disarming operationTo disarm the system press transmitter button * The siren will chirp twice.* The parking lights will flash twice.* The doors will unlock.The LCD transmitter will beep twice and display asbelow:

F4/1: Doors will not be unlocked when the ignitionturns off.

F4/2: Doors will be unlocked automatically when theignition turns off.

During driving, press button or to lock or unlockthe doors

9. Dome light delayThis function is specifically designed for the vehiclewith dome light function. The system will enter thearming mode after the dome light turns off. Armingdelay time can be set by F6.

10. Remote panic:In the event of an emergency (panic) situation, thesiren can be triggered for 30 seconds to attractattention. Press and hold transmitter button +

for 2 seconds to activate the panic function:* The siren will chirp sharply.* The parking lights will flash.

Press and hold transmitter button + for 2seconds or press valet switch (if a personal code isset, you should enter the personal code) to exit.

11. Time/ alarm time/W-mode settingPress button + to turn on/off the LCD transmitter'svibration mode.Press and hold button for 5 seconds to activatetime /alarm time /W-mode setting mode.Press button once, the LCD transmitter beeps

once, the hour digit will flash, then press button ,the flashing icon will change in the sequence below:time/hour time/minute alarm on/off alarm/hour

alarm/minute W-mode setting exit.

Press " " to increase (+) or press " " todecrease (-).

Press and hold button for 1 second to save andexit setting.

W-mode: Press + button together shortly toturn W-mode on/off. According to F21, CH6 canbe activated.

"W-mode" means the time of transmitter sendingsignals to system can be programmed.The "set"icon will be shown on the LCD transmitter.

12. Low battery indicatorThe battery status of the LCD transmitter will beshown on the LCD display. When the batteryindicator is empty, the transmitter needs to becharged immediately.

13. Trunk releasePress or button to open the trunk. Theshock sensor will bypass when the trunk is opened,and return to normal when the trunk is closed.

The vehicle must equip with trunk release motorand select or output for trunk releaseduring installation.

7. Remote sensor bypassTo arm the system and bypass the 1-stage of theshock sensor: press button , then press button in 3 seconds, the siren chirps once and the 1-stageof the shock sensor will be ignored for one cycle.

To arm the system with both sensors bypassed: pressbutton , then press button twice in 4 seconds,the siren chirps twice and both sensors will be ignoredfor one cycle.

The operation of remote sensor bypass in mutearming mode is the same.

8. Central door lock/unlock (F3/F4/F15/F25).F3/1: Doors will not be locked when ignition turns on.

F3/2: Doors will be locked automatically when ignitionis turned on.

F3/3: If you program F15/2 for speedometer input,doors will be locked automatically when the car speedreaches the pre-set speed.

F3/4: If you program F25 for "door +" or "door -", andconnect wires to footbrake signal wires, doors arelocked when the foot brake is pressed.Note: If one of the doors are not closed properly, the doorswill not be locked.

4. Silent arming/disarmingPress transmitter button , then press button or , the system will arm or disarm without sirenchirp(s).

5. Mute armingPress and hold transmitter button for 2 secondsto arm in mute mode* The siren will not chirp for one cycle* The parking lights will flash once.* The doors will lock.When the system is triggered, the siren will not chirp.The LCD transmitter will show as below:

6. Car searching (locating)Press and hold transmitter button + for 2seconds, the siren will chirp and parking lights willflash 5 times.

8 9

14. Arming without transmittersPress valet switch once, then press and hold itagain for 3 seconds. The siren will chirp once, theLED will flash rapidly. The system will be armedafter all doors are closed and send the signals toLCD transmitter. If F24 is on, then the doors willbe locked. This function is only for one operation.

15. Anti-hijack modeAnti-hijack mode will be activated automatically orby transmitter (Function F16/F17/F18).Five anti-hijack modes can be programmed:1) Anti-hijack off.2) Active: press and hold transmitter button + for 3 seconds to activate the anti-hijack function.3) Full-time: anti-hijack function will be activatedas soon as ignition is turned on.4) Passive activated with door opened: Duringdriving, opening the door will activate anti-hijackfunction.5) Passive activated by speed: the pre-set speedwill activate the anti-hijack function.

ACC off can stop alarm temporarily. Once ACC isturned on, the system will alarm and block theengine.

Once the anti-hijack mode is activated:1) In 20 seconds, the anti-hijack icon flashes onthe transmitter, the siren does not chirp.2) 20 seconds later, the siren will chirp and the

engine will be blocked periodically.3) 40 seconds later, the siren will chirp with parkinglights flashing rapidly until the car battery is usedup, the engine will be blocked completely.

To deactivate the anti-hijack function:1) In 40 seconds, press valet switch once.2) 40 seconds later, to deactivate the anti-hijackfunction depends on the setting of F12.I. F12 is "Valet" - turn ignition OFF/ON and pressvalet switch once in 10 seconds.II. F12 is "Personal code" - enter personal code byvalet switch [24.1].

16. Transponder card (optional)Please program transponder card into the memory ofthe system before use.

3 modes of transponder card can be programmed(Function F13)

1) F13/1 Transponder card is deactivated.

2) F13/2 Transponder card is activated with engineblock function:I. Once ignition is turned on, the system starts tosearch transponder card in 1 minute. If the systemfinds transponder card, the LED indicator flashes(1 long + 3 short) and the system will send signalto the LCD transmitter.If system can not find transponder card in 1 minute,the engine will be blocked.

If door is opened and stays open, then the systemwill delay transponder card searching for 4 minutes.One more minute later, if transponder card is notfound, the engine will be blocked.

II. To change this protection mode, change F25 for"door +" or "door -" and connect correspondingdoor trigger wire to the footbrake wire.The following will happen:* If door is opened, the system will searchtransponder card when the footbrake is pressed.* If the footbrake is pressed and transponder cardis not found in 1 minute, engine will be blocked.* If door is opened, the system will searchtransponder card in 4 minutes when the footbrakeis not pressed.* If transponder card is registered successfully withdoor closed, pressing footbrake will not activatetransponder card searching, opening door willactivate transponder card searching.

3) F13/3 Transponder card is activated with anti-hijack function: once ignition is turned on, systemwill search transponder card. If system does notfind transponder card in 1 minute it will activateanti-hijack.

If you place the transponder card in the workingrange in 40 seconds when anti-hijack function isactivated, anti-hijack will be stopped.

If you place the transponder card in the workingrange after 40 seconds when anti-hijack functionis activated, you need to deactivate anti-hijack, byvalet switch or enter personal code.

17. Valet (service mode)To activate Valet mode:Disarm system, turn ignition on for more than 3seconds then turn off, press the valet switch oncein 5 seconds. The LED will turn on solid. The sirenwill chirp once every time when the ignition is turnedoff in valet mode.

In valet mode, doors lock/unlock and panic functionscan be operated by transmitter.

To deactivate valet mode:Turn ignition on for more than 3 seconds then turnoff, press valet switch in 5 seconds.

18. Emergency overrideIf the transmitter is lost or fails to operate, the systemcan be disarmed by using the emergency overridefeature. To override the system depends on F12.

F12 -"Valet":Opening the door with key ( the siren will chirp). Turnignition on, press valet switch once in 10 seconds.

F12 -"Personal code":Enter the personal code [24.1].If wrong personal code was input three times, youneed to wait for more than 3 minutes to enter personalcode again.

10 11

19. Turbo timer mode (F1, F19, F21)The time can be programmed (F1). Turbo timerworks after the engine runs for more than 60 seconds.If the turbo timer mode is on, when you take out thekey, the engine will keep running, the parking lightswill flash once every 2 seconds. The remaining timewill be shown on LCD transmitter.

Turbo timer mode keeps the engine running afterarriving at you destination for a programmable periodof 1, 3, 10, 15 or 30 minutes (F1). This allows thesystem to cool down the turbo after you have leftthe vehicle.

To activate turbo timer mode, "turbo timer output"(F19/2 or F21/2) needs to be set.* Turn off the key, the engine will keep running.* The LCD transmitter will beep 3 times and thedisplay will show: * The parking lights will flash once every 2 secondsto indicate the turbo timer mode is on.* The engine will turn off after the programmed timeruns out.

To cancel turbo timer mode:a) Take the key outb) Press button twicec) Siren will chirp twice and the parking lights willflash once.

20. Transmitter operation range indicationIn armed mode, the signal icon on the operated LCD

transmitter shows that the transmitter is within theoperation range of the system. The signal icon willdisappear in 2 minutes when the LCD transmitter isout of the operation range and cannot receive thesignal from the system. At the same time, 2 beepswill be heard when any LCD transmitter button ispressed.

When a transmitter sends signal to the system, thesystem only send feedback signal to the transmitter.

21. Rearming automaticallyWhen the system is disarmed by pressing button and the doors are not opened in 20 seconds (plusF6 arming delay time), the system will rearm with thedoors locked automatically (door lock or unlock isdetermined by F5). The siren will beep once withparking lights flash.

22. Ultrasonic sensor (optional)When the ultrasonic sensor is triggered by detectingan object movement inside the vehicle, the siren willalarm for 30 seconds with parking lights flashing. Theengine will be immobilized.

23. Tamper alertIf the alarm was triggered while you are away fromthe vehicle, the siren will chirp 4 times with the parkinglights flash on disarming for tamper indication. TheLED will flash the zone that was triggered.

24. Personal code settingPersonal code can be programmed (F12). The factorysetting personal code is 11.

24.1. How to enter the personal code:Disarm system, turn ignition off and wait for 5seconds, then turn ignition ON/OFF/ON.Press and release the valet switch the number oftimes according to the first digit of personal codein 10 seconds. (eg. The first digit of factory settingpersonal code is 1, press and release the valetswitch once).

Turn ignition OFF/ON.Press and release the valet switch the number oftimes according to the second digit of personal codein 10 seconds.

Turn ignition OFF/ON.When the input personal code is correct, the systemwill send out a "short" chirp and a "long" chirp.

24.2. How to change the personal code:After the correct personal code is entered, turnignition off in 5 seconds.Press valet switch 5 times, the siren will send outone short and one long chirp to confirm entering thesetting mode.Press transmitter button once in 5 seconds (thesiren will chirp once).Press valet switch the number of times accordingto the first digit of the personal code (from 1 to 9)in 10 seconds, the siren will chirp accordingly.Press transmitter button once in 10 seconds (thesiren will chirp once).Press valet switch the number of times accordingto second digit of personal code (from 1 to 9) in

10 seconds, the siren will chirp accordingly. Turnignition on, the siren will send out one short and onelong chirp to confirm the new personal code is setsuccessfully.If the changing is not successful, please disarm thesystem and repeat the procedure mentioned above.

25. Transmitter and transponder (optional) codelearningTo learn new transmitters, the learning procedureswill be different depending on the settings of F12:

F12 - valetSwitch off the power of the transponder card (ifavailable)

Disarm system, turn ignition on.Press valet switch 3 times, the siren will chirp once.Press and hold button on the first transmitter tillone chirp is heard, and then LED will start to flashslowly.Press and hold button on the second transmittertill one chirp is heard, and then LED will start to flashslowly.Only 2 transmitters can be programmed for thesystem.

Switch on the power of transponder card, thetransponder card will be programmed successfullywith one chirp.Turn ignition off to exit or 10 seconds later to exitautomatically.

12 13

Car alarm system

Installation Manual

14 15

System will enter the F1 programming mode (LEDwill flash once after one pause).In programming mode, the number of times LEDflashes is corresponding to the function number.

To change function setting, press transmitter button (1~5 times). According to the different function

settings, the siren will send out 1/2/3/4/5 chirps.Press valet switch to go to next function.

If you do not press any button in 10 seconds,system will exit programming mode.

F12 - Personal code: function programmingEnter the personal code [24.1].Siren chirp will confirm if personal code is correct.Press valet switch 3 times in 3 seconds. Siren willchirp once.Turn ignition off in 3 seconds. Siren will chirp once.Turn ignition on in 3 seconds. Siren will chirp once.System will enter the F1 programming mode (LEDwill flash once after a pause).

In the programming mode, the number of the LEDflashes is corresponding to the function number insystem programming table.

To change function setting, press transmitter button. According to the different function settings, the

siren will send out 1/2/3/4/5 chirps.

Press valet switch to program next function.If you do not press any button in 10 seconds,system will exit programming mode.

F12 - personal codeSwitch off the power of the transponder card (ifavailable)Follow the steps of "How to enter the personalcode" [24.1], the siren will chirp once to confirm ifpersonal code is correct.Press valet switch 3 times, the siren will chirp once.Only 2 transmitters can be programmed for thesystem.Switch on the power of transponder card. The sirenwill chirp once to confirm transponder card isprogrammed (If available).Turn ignition off to exit or 10 seconds later to exitautomatically.

26. System programmingF1-F10 can be programmed and it is independentof F12.F12 - valetF1-F25 can be programmed.F12 - personal codeF1-F10 can be programmed without personal code.F11-F25 can be programmed only after enteringpersonal code. System will exit programming modeif there is no button pressed in 10 seconds.

F12-valet: function programmingDisarm system, turn ignition on, press valet switch3 times in 3 seconds. Siren will chirp once.Turn ignition off in 3 seconds. Siren will chirp once.Turn ignition on in 3 seconds. Siren will chirp once.

16 17

System programming table

System programming table

To be continued

When disarmed,signal "-" 20 sec

5 chirps1 chirp 2 chirps 3 chirps 4 chirpsFunction

F1 1 min 3 min 10 min 15 min

Footbrakelocking (Ref.F25)

30 min

Description

Turbo timer

Limitation offalse alarm

Ignitionlocking

Ignitionunlocking

Auto rearm

Door locking/unlockingpulse

CH2 output

CH3 output

CH4 output

Press button once

Press button twice

Press button 3 times

Press button 4 times

Press button 5 times

Press button CH2signal "-" 1 sec

Press button CH3,signal "-" 1 sec

When armed,signal "-" 1 sec

On withunlocking

35 sec

1 sec

Press button CH2signal "-" 30 sec

Press button CH3,signal "-" 3.5 sec

When armed,signal "-" 10 sec

Speed locking

On withlocking

60 sec

3.5 sec

Press button CH2,signal "-", pressbutton CH2 againto stop

Press button CH30.4 sec, signal "-" 12 sec

When armed,signal "-" 15 sec

When armed,signal "-" 30 sec

Press button CH3,signal "-" 0.4 sec,pause 0.3 sec,signal "-" 0.4 sec

F2

F3

F4

F5

F6

F7

F8

F9

F10

Signal "-" whenignition on

1 sec unlockpulse ×2

Press button CH3,signal "-" 1 sec,pause 0.5 sec,signal "-" 1 sec

Arming delay

Off

5 sec

0.5 sec

Off

Off

Off

On

On

On

5 chirpsFunction

Programming the function F12- F25 depends on the mode of F12, "valet mode" or "personalcode mode" are available.

F15

F16

INST2 (-)extra inputtrigger

Anti-hijack bytransmitter

Anti-hijack byignition on

Anti-hijack byignition on

Off

On by driverside dooropening (+)

On

Speedometerinput (-)

On

On

Personal code

On while anti-hijack activated

On by driverside dooropening (-)

On by speed

Continued

F11

Description

Restorefactory setting

Valet/Personalmode setting forprogramming

Transpondercard

Ignitionwarning indisarmedmode

F12

F13

F14

F17

F18

F19

Off

Valet mode

Off

Off

INST2 (-)extra inputtrigger

1 chirp 2 chirps 3 chirps 4 chirps

On

To be continued

On

Off

Off

Turbo timeroutput (-)

18 19

Continued

The shaded options are factory setting

Note:F1 Turbo timerTurbo timer function will be activated after ignitionis on for more than 1 minute (F19/2 or F21/2 needto be programmed). It will keep a turbo vehicleengine running for 1, 3, 10, and 15 or 30 minutesaccording to F1 after you remove the key.

F2 Limitation of false alarmIf the same input triggers the system 6 times duringa single arming cycle, the system will bypass that

input, keeping the other zones protected until thenext time the system is armed.

F3 Ignition lockingF3/1: the doors will not be locked automaticallywhen ignition is on;F3/2: the doors will be locked automatically whenignition is on;F3/3: the doors will be locked when the car's speedreach the pre-set speed (with F15/2)

Pager (-)

5 chirps1 chirp 2 chirps 3 chirps 4 chirpsFunction

F23

F24

Passivearming

Door lock ifpassivearming on

When disarmed,signal "-" 20 sec

Off

Off

Off

On

On

10 sec

Turbo timer(-)

Description

CH6 output:two blue/blackwires

Window/sunroof closer

F20

F21

F22

CH5 output

Off

Door (+) Door (-)

15 sec

W-trigger (startand stop byreal time)

W-trigger (startfor 1 sec byreal time)

22 sec 30 sec

W-trigger (startfor 1/0.5/1 secby real time)

F25STOP (-/+)function ofdoor trigger

F3/4: the doors will be locked when footbrake ispressed (by F25) automatically.The system will not lock the doors if any door isopened when the ignition is turned on.

F4 Ignition unlockingF4/1: the doors will not be unlocked when ignitionis off;F4/2: the doors will be unlocked automatically whenignition is off;

F5 Auto rearmAutomatically rearms the system in case ofaccidental disarming. Select among auto rearm off,auto rearm without door locking and auto rearmwith door locking.

F6 Arming delayThis optional arming delay mode allows system todelay arming for 5, 35 or 60 seconds. This modeis designed for vehicle with dome light delay.

F7 Door lock/ unlock pulseSelect between a 0.5 second lock/0.5 second unlock,1 second lock/1 second unlock for standard vehicles,3.5 seconds lock/3.5 seconds unlock for vacuumlock system, 1 second lock/1 second unlock 2 timesfor some Japanese vehicles.

F8 CH2 outputPress transmitter button CH2 to activate this feature:F8/1: the blue wire will output signal (-) for 1 second

to turn on device, such as releasing trunk.F8/2: the blue wire will output signal (-) for 30seconds to roll up windows.F8/3: the blue wire will output signal (-), press CH2button again to stop output signal (-).F8/4: the blue wire will always output signal (-) afterignition on.

F9 CH3 outputPress transmitter button CH3 to activate this feature:F9/1: the green/red wire will output signal (-) 1second to turn on device, such as releasing trunk.F9/2: the green/red wire will output signal (-) for 3.5seconds.F9/3: the green/red wire will output signal (-) for 12secondsF9/4: the green/red wire will output signal (-) for 0.4seconds, pause 0.3 seconds and then output signal(-) for 0.4 seconds again.F9/5: the green/red wire will output signal (-) for 1second, pause 0.5 seconds and then output signal(-) for 1 second again.

F10 CH4 output:F10/1~4: When the system is armed, theGreen/White wire can output signal (-) for differenttime to activate other devices: 1 second, 10 seconds,15 seconds or 30 seconds.F10/5: when the system is disarmed, theGreen/White wire will output signal (-) for 20 seconds.

20 21

F11 Restore factory setting:This option allows the system to restore the factorysetting rapidly.

F12 Valet/Personal mode setting for programmingThere are two modes of F12: Valet mode and Personalcode mode.When F12 is in Valet mode, you can program thefunctions/features of F12~25 through Valet switch.When F12 is in Personal code mode, you can programthe functions/features of F12~25 by input personalcode.

F13 Transponder cardThe transponder card is an additional upgradeaccessory.F13/1 Turn off the transponder card detection.F13/2 Turn on the transponder card detection. If thetransponder card is not found, the engine will beimmobilized.F13/3 Turn on the transponder card detection andanti-hijack will be activated automatically when thetransponder card is not detected.

F14 Ignition warning in disarmed mode In disarmed mode, when ignition is on, the ignitionicon ( ) will show on the LCD transmitter.

F15 INST2 (-) extra input triggerSelect between an INST2 extra input (-) or aspeedometer input (-).

F16 Anti-hijack by transmitterTo activate the anti-hijack by pressing transmitterbutton and together when ignition is on.

F17 Anti-hijack by ignition onTo activate the anti-hijack by ignition on or by adoor opening (-) while the ignition is on.

F18 Anti-hijack by ignition onTo activate the anti-hijack by a door opening (+)while the ignition is on or by the speedometer trigger.

F19 Arm (-)F19/1: The output (-) of Black/White wire is reverseto the armed output (-) (Orange wire). That means,when the Orange wire outputs signal (-), theBlack/White wire will not output signal (-), when theOrange wire does not output signal (-), theBlack/White wire will output signal (-).F19/2: Black/White wire will output signal (-) forturbo timer.

F20 CH5 outputF20/1: The output (-) of Gray wire is reverse to thearmed output (-) (Orange wire).F20/2: The Gray wire will output a signal (-) to triggera pager when the alarm system is triggered.

F21 CH6 output: two blue/black wiresSelect between turbo timer and W-mode.F21/1: output signal (-) for 20 seconds afterdisarmed. This option is recommended to triggerthe headlight output.

Installation instruction

Before you begin the installation* Read the INSTRUCTIONS!

* Always use a multi-meter when verifying vehiclewiring.

* Before mounting the product, verify with thecustomer's desired location for the valet switch andLED.

* Always look before drilling. Make sure you will notcause damage to vehicle hoses, electrical looms orphysical damage to vehicle.

Mounting ECUMount the ECU under the dash where it will bedifficult for a potential thief to locate the module,and away from moving parts such as brake pedals,etc.

Antenna moduleFor optimum range and performance, the antennamodule should be located high up on the frontwindshield glass. For example: behind the rearviewmirror.

Note: Window tints or Films may decrease the rangeof the system. The mounting surface for the antennashould be clean and dry.

Mounting sirenMount the siren in a suitable place under the hood,away from hot and moving engine parts. Make surethe siren cannot be accessed from underneath the

F21/2: output signal (-) for turbo timer according tothe time of the F1 setting.F21/3/4/5: The channel will activate according tothe W-mode setting. Select among1 start and stop by real time (according to the W-mode setting to start and stop);2 start for 1 second by real time (according to thew-mode setting to start for 1 second signal);3 start for 1/0.5/1 sec by real time (according tothe w-mode setting start for 1 second and pausefor 0.5 second then a 1 second signal)

F22 Window/sunroof closerThis option suits for vehicle with automaticwindow/sunroof close function. Select for 10seconds, 15 seconds, 22 seconds or 30 secondsto close the window/sunroof.

F23 Passive armingThe system will arm automatically 30 seconds afterthe car is parked and all doors are closed.

F24 Door lock if passive arming onAll doors will lock while passive arming.

F25 STOP (-/+) function of door triggerF25/1: no change to the door triggerF25/2: door trigger (+) wire (violet) will be definednot for door trigger, e.g. it can be defined as afootbrake trigger (+).F25/3: door trigger (-) wire (brown) will be definednot for door trigger, e.g. it can be defined as afootbrake trigger (-).

* YELLOW WIRE -- IGN1, +12V ignition input.Connect to a main ignition wire at the ignition switchharness. This wire shows +12V when the ignitionis on and while cranking. The voltage must not dropwhen the car is starting.

* GREEN / RED WIRE -- CH3 output (-) 1A. Pleaserefer to the System programming table F9.

6-Pin door lock connector

* BLUE / WHITE WIRE -- Lock relay N/O (87).

* YELLOW WIRE -- Lock relay Common (30).

* GREEN WIRE -- Lock relay N/C (87a).

* ORANGE WIRE -- Unlock relay N/O (87).

* WHITE WIRE -- Unlock relay common (30).

* BLUE WIRE -- Unlock relay N/C (87a).

Plug in connectors2-Pin Connector: Plug-in connector port for LED.Mount LED in an area where it may be easily seenfrom either side of the vehicle.

2-Pin Connector: Plug-in connector port for valetswitch. Mount switch in an area that is easilyaccessible from the driver's seat. The switch shouldbe well hidden. It should be placed so passengersor stored items (such as in a glove box or centralconsole cannot accidentally hit it.

4-Pin White Connector A: Plug-in connector portfor 2-stage shock sensor.

4-Pin White Connector B: Plug-in connector portfor optional ultrasonic sensor.

IGN1(+)

IGN2(+)

Output ignitionwire from carignition lock

Ignition contactof car ignitionlock

Wire thatsupplies+12 Vto car ignition lock

22 23

* BLUE/ RED WIRE - INST2 input (-).a. Connect to hood pin switch or trunk switch.b. Connect to speed sensor of "VAZ" vehicle (F15.F3).

* RED WIRE -- +12V Battery input. Connect the redfused wire on the main harness to a constant +12Vsource.

* BROWN WIRE -- Negative door trigger (-). Connectto the door switch circuit wire that shows groundwhen the door is open.

* WHITE WIRE --Parking lights output (+). Connectto the vehicle's parking lights wire.

* VIOLET WIRE -- Positive door trigger (+). Connectto the door switch circuit wire that shows +12V whenthe door is open. This type of door circuit is usuallyfound on Ford vehicles.

* GREEN / WHITE WIRE - CH4 output (-) 500mA.(F10).

* BLUE WIRE - CH2 output (-) 500mA. (F8).

* GRAY WIRE - CH5 output (-) 500mA. (F20).

* BLACK / WHITE WIRE - ARM (-) 500mA.

* BLUE / BLACK WIRE - CH6 output (-) 1A. ( F21).

* YELLOW / BLACK WIRE -- IGN2, +12V ignitioninput. Connect to the wire going to the starter. Thevoltage of this wire output can keep engine runningaccording to the Turbo timer.

vehicle or through the grill. Face the siren down sothat water cannot accumulate inside the siren bell.

Protect wires running through the firewall usingeither tape or split loom tubing.

Mounting shock sensorSecure the shock sensor to the steering column,thick wire harness or a dash brace, using a wire tie.

Make sure that the adjustment screw is accessiblefor later testing and adjustment.

20-Pin main harness* BLACK WIRE -- Ground input (-). Connect to asolid chassis ground that is clean and free of paintor dirt.

* ORANGE WIRE -- Armed output (-) 500mA.Connect to a relay for optional circuit defeat (Seeinstallation diagrams). The ORANGE wire providesa ground 40 seconds when the unit is armed toactivate a fuel pump disable relay or other device(i.e. window control module, etc.).

* BLUE / BROWN WIRE - INST1 input (-). Connectto hood pin switch or trunk switch. The BLUE /BROWN wire provides a ground when the hood ortrunk opened.

* WHITE / BLACK WIRE -- Siren wire output 5A(+).Connect to the siren's red wire. Connect the siren'sblack wire to ground.

Contact of additional relay to controlturbo timer mode for channel ARM (-),CH6 or "TRIGGER" of channel CH2.

24 25

Door lock wiring diagrams

GREEN

YELLOW

BLUE/WHITE

BLUE

WHITE

ORANGE

NC

COM

NONC

COM

NO

L

UL

XX

CUT

CUT

+12V

RREEVVEERRSSEE PPOOLLAARRIITTYY LLOOCCKK SSYYSSTTEEMM

NNEEGGAATTIIVVEE PPUULLSSEE LLOOCCKK SSYYSSTTEEMM

(-) DOOR LOCK

(-) DOOR UNLOCK

GREEN

YELLOW

BLUE/WHITE

BLUE

WHITE

ORANGE

NC

COM

NONC

COM

NO

L

UL

PPOOSSIITTIIVVEE PPUULLSSEE LLOOCCKK SSYYSSTTEEMM

(+) DOOR LOCK

(+) DOOR UNLOCK

GREEN

YELLOW

BLUE/WHITE

WHITE

ORANGE

NC

COM

NONC

COM

NO

+12V

L

UL

BLUE

GREEN

YELLOW

BLUE/WHITE

WHITE

ORANGE

NC

COM

NO

NC

COM

NOL

UL

X CUT

+12V

VACUUM PUMPVVAACCUUUUMM LLOOCCKK SSYYSSTTEEMM

BLUE

AADDDDIINNGG AACCTTUUAATTOORRSS

GREEN

YELLOW

BLUE/WHITE

WHITE

ORANGE

NC

COM

NONC

COM

NO

+12V

BLUE

Optional relay wiring diagrams

Hood / trunk pin switch relay wiring diagrams

Hood / trunkpin switch

V

To hood / trunkrelease

Blue

26 27

Wiring diagram

15A

Parking lights

Blue / Brown INST1(-)

White / Black

Blue / Red INST2(-)

Brown Door trigger (-)

5A

Door trigger (+)

Green / White CH4 output (-)

Blue CH2 output (-)

Gray CH5 output (-)Blue / BlackCH6 output (-)

Yellow / BlackYellowIGN1 (+)

IGN2 (+)

Green / RedCH3 output (-)

Black / WhiteArm (-)

5A

7.5A

7.5A

Green / Red

Blue / Black

20

Sensor (optional)

Troubleshooting

Fault Causes1. The continuous chirping of the siren cannotbe stopped by transmitter after the installationof ECU.

The plug is improperly inserted. The wire is improperly connected. The transmitter does not match the ECU. The siren is damaged. The fuse of the ECU is broken

Door trigger wire is not connected properly. Door switch has problem. The siren is damaged.

3. When the car parks on roadside and armed,there are false alarms by passing heavyvehicles.

2. Parking lights do not flash after disarmingthe system and opening the door, or the sirendoes not chirp when the door is opened withoutdisarming.

The sensitivity of the sensor is too high.

4. The central door lock does not work normallyor does not work at all.

The motor of central lock is damaged. The wiring of central lock system is wrong. Fuse is broken.

5. The siren does not chirp when the alarmsystem is triggered.

The siren is damaged. The wire connection between the siren and ECU

has problem.

6. The siren chirps sharply in 10 seconds afterarming and the same situation happened afterdisarming and re-arming it again.

The sensor is damaged. The doors or trunk is not closed. The door's pin switch has problem or wiring has

problem.

7. Transmitter is ineffective or the controldistance decreased significantly.

The installation location of the antenna is wrong. The wiring of the antenna to ECU has problem. Tall building, radio tower or high frequency

electromagnetic wave may affect the remote range. Low power of the battery. The frequency of the transmitter has been

changed. The transmitter is broken or damaged.

Warranty

I. The unit is warranted for a limited period fromthe date of purchase. In the unlikely event of adefect arising in this product when used inaccordance with the manufacturer's instructions,the parts would be repaired or replaced free ofcharge.

It is required to show warranty card whenmaking any warranty claims.

The model and serial number on unit must bethe same as the information on the warranty card.

II. This warranty is non-transferable and isautomatically void if:

The original purchaser has not completed thewarranty card.

The unit's serial number is defaced, missing oraltered.

The unit has been modified or used in a mannercontrary to its intended purpose.

The unit has been damaged by accident,unreasonable use, neglect, improper installationor service.

III. The warranty does not cover damage to theunit caused by installation or removal of the unit.

User:

Tel:

Vehicle Reg No.:

Product Model No.:

Serial No.:

Date of Installation:

Name of the Retailer:

Signed by Retailer:

Steelmate warranty card

28