Issued 2017 Dry to touch 4 hours. Full dry 24 hours. Recoating interval 24 hours. (minimum) 7 Days. (maximum) Full cure 7 Days. All above drying time tested according to ASTM D5895@25°C. Air spray Thinning ratio: (20–30)% by volume. Nozzle size: (1.8–2.0) mm. Airless spray Thinning ratio: (0–10) % by volume for (150–200) μ D.F.T. (10-15)% by volume for (100–150) μ D.F.T. Nozzle size: 0.48mm.(approximately). Roller / Brush Thinning ratio: (15–25) % by volume. AL-JAZEERA COAL-TAR EPOXY A two-component polyamide cured coal tar epoxy . Recommended to use as a protective coating on steel and concrete surfaces, where extreme corrosion resistance is required. It is specially suitable for under-ground pipes and foundations submerged surfaces splash zone. It can be applied on under water part of the ship and under surface of vehicles. “Al-Jazeera Coal-Tar Epoxy” has the following features: -Strong protective coating on steel and concrete surfaces. -Excellent adhesion with steel, cement, concrete and galvanized iron. -Excellent resistance to alkali, seawater, sewage water, salty water, crude oil. -Highly flexible. Finish: Semi-gloss. Colour: Black. Specific Gravity: 1.40(mixed paint), ASTM D1475. Viscosity: 107 KU (Mixed Paint), ASTM D562. Volume Solid: 64 %. ASTM D2697. D.F.T: 150 μ. Depending on the surface and system. Theoretical Spreading Rate: 4.27m 2 /L (171.1 ft 2 / US gallon). at D.F.T. 150 μ.(to avoid waste, be sure to buy the right amount of the paint for the surface area required). Hardness: Pass, 2 H Pencil, ASTM D3363. Scratch Resistance: Pass, 1 Kg., ASTM D5178. Bending: Pass, 3 mm. Diameter, ASTM D522. Adhesion: Pass, ASTM D3359 and 400 psi, ASTM D4541-III. Impact: Pass, 1 Kg. / 1 meter / 16.3 mm. Diameter. ASTM D2794. Water Resistance: Pass, ASTM D870. Chemical Resistance: Pass, ASTM D1308. Flash Point: 28°C. Remove old paint from surfaces completely and make sure that the surface is clean, dry , free from dust, oil, grease, salt and old paint. Fill the holes and cracks with suitable fillers "Jaz Epoxy Crack Filler ESP" prior to application of the paint. STEEL: The surface should be prepared by abrasive blasting accord- ing to standard Sa2 ½. (ISO 8501-1:1988) to have a proper roughness and cleanness (40-70 μ). CONCRETE -All new surfaces must be cured at least for 30 days prior to application of the primer. -The surface must be treated by removing all forms release and protrusions to get a suitable surface for application. -Remove old paint from surfaces completely. APPLICATION GUIDE: PACKING: SHELF LIFE & STORAGE: INDUCTION TIME: PAINTING SYSTEM: JI-67001 POTLIFE: DRYING TIME: SURFACE PREPARATION MIXING RATIO: APPLICATION TOOLS AND THINNING RATIO: THINNER: 1.The surface must be removed from dust , grease, oil and other contaminants completely. 2.The surface must be treated by removing all forms release and protrusions to get a suitable surface for application. 3.Surface temperature required during application must not be less than 10°C; the surface moisture should not exceed 8% and the relative humidity at work place not to exceed 70%. 4.Maximum pH of 9 for concrete surfaces . 5.Make sure that, base paint and hardener are mixed uniformly. 6. A suitable quantity of “Al-Jazeera Thinner 505” can be added to get reasonable viscosity for application. 7.The mixed paint should be used within pot-life. 8.Do not apply the next coat unless the previous one is fully dry, minimum recoating interval time should be given between the two coats. By volume: Base Hardener 3 : 1 6 hours at 25°C. (After mixing). 20-30 minutes after mixing the base and hardener. Apply two coats of " Al-Jazeera Coal Tar Epoxy" as a primer and finish directly. Recommended thinner is “Al-Jazeera Thinner 505”. Base Hardner US Gallon 2.70 Ltr. 0.90 Ltr. 18 Ltr. Drum. 13.50 Ltr. 4.50 Ltr. Shelf life : 12 months @ 25 °C. Storage: The container should be kept in sealed, dry, cool, well ventilated place and stored in accordance with national regulations. DESCRIPTION: CHARACTERISTICS: RECOMMENDED USE: PHYSICAL CONSTANTS: Technical Data Sheet Disclaimer To the best of our knowledge the technical data listed herein is true and accurate up to publication date and is subject to change without prior notice. User must contact Al-Jazeera Paints Company to verify of any modifications before specifying or ordering the product. Thus, information given in this sheet is not intended to be exhaustive and any person using the product other than the recommendations in this sheet or without reverting to our Al-Jazeera TSD, he should take his accountability in this connection. We don’t have the ability to control the quality and condition of the surface as well as the any of factors affecting the use of application or the product , thus we haven’t pre sended any written or implied warranty through these documents , we only guaranty our product in line with the quality of Al-Jazera and we don’t assume any accountability for performance or injuries resulting from using the product , liability if any is limited to replacement of product.