This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Module 1 - Brushes• 5 steel wire brushes for cleaning the
injector shaft (18, 19, 21, 24 and 26 mm)• Brush holder & flexible bit holder ¼“• 1 pipe brush• 2 end brush steel (Ø 17 mm) &
plastic guide• Setting tool and sealing plugs 8 & 10 mm
Module 2 - MillingIn case the sealing seat is severe contaminated or damaged, then can be reworked with the milling tool, precisely and under controlled conditions, so that again a perfect sealing surface is formed.• 3 sealing seat milling cutters• basic device with 3 cones and depth stop• cutting grease• allen key
Module 3 - AccessoriesSealing Ring Extractor. For extracting the frozen copper sealing rings from the injector shaft, without damaging the cylinder head. Including 1.35 kg slide hammer and flexible lamp.
Nissan, Opel, Toyota• ANK 63 ½“ x 20 UNF Pontiac• ANK 53 M16 x 1,5 Citroen, Peugeot, Renault
Universal Compression Test Adapter Set M8x1, M9x1, M10x1, M10x1.25 Suitable Adapters Universal tool for the compression check through the glow plug bore. Connector for test equipment: M12x1.5
• Versatile by combining guides, sealing cones and adapters
Pneumatic Impact Wrench ⅜“ „Butterfly“
• Light and handy• Torque max. 102 Nm• Turnable compressed air connection• 8 setting steps• Idle speed 9000 rpm
Particularly suitable for working in the engine compartment
• With the suitable adapters usable for several compression testers
• M12x1.5 to NW 5
• M12x1.5 to Euro coupling
• M12x1.5 to BSP ¼“
Engine PositionerIs used during the mounting of the engine in the engine compartment. The engine positioner allows a precise positioning of the engine.• Lifting capacity: 250 kg
Universal Engine and Gearbox SupportUser-friendly engine- and gearbox support, which is a „Universal Tool“ that does not work with a base unit and various extensions, but as one unit with a jack.
Digital Infrared ThermometerUniversal non-contact thermometer. With two laser points to a single spot when the unit is at the optimal distance from the target.
• Ideal for exhaust system, air-conditioning, cylinder temp- erature, brake temperature, cooling system temperature.
• Automatic measurement memory• Temperature range : -50°C to 1000°C
For work on the shop press, e.g. of transmissions, axles, etc.. For very limited space. Special steel, very slim design.
Universal wheel bearing replacement kit with combined hub/axle shaft press clamp. The wheel bearing is repla-ced directly on the car with minimum work.
• 170 x 280, 4 mm• Opening max. 69 mm, min. 29 mm
Universal
• Neither ABS-sensor, wheel spindle, spring strut nor steering linkage needs to be dismounted.
• Without hydraulics
Wheel Hub GrinderFor cleaning and rust removal of wheel centering and the contact surface.
Ø 200 mm with 2 Cleaning Discs
Ø 160 mmwith 3 Cleaning Discs
Press and Pull Sleeve Set IIUniversal set of tools for removing and pulling in e.g. bushes, hydraulic bearings, bushings, bearings and oil seals.
• Reliable and uniform actuation
Suited for: SUV / off-road vehicles e.g. BMW X3, X5, X6, MB M-class, Porsche Cayenne, VW Touareg and commercial vehicles
Application picture
Universal Puller for pressing the ball joint stud from the steering arm in trucks and buses, as well as stub axles for transportation vehicles.
• Is especially suited for releasing ball joint connections on axle and steering systems
• High durability and safety
• for use with hydraulic cylinder 8,5 ton
Steering Joint Puller
Application picture
Universal Compact Wheel Bearing Mounting ToolUniversal tool for mounting the new type of compact wheel bearings, with or without locking ring.
• Including 3 holding plates and mounting ring for different vehicle types
• Without hydraulics
Tire Changing Promotion Package
• max. torque 1600 Nm at 6,2 bar
Impact gun ½“
Torque wrench up to 210Nm• With reversible ratchet, fine-toothed• Accuracy ±3%• Drive ½“
Impact socket set ½“ 3 pc• Specifically for removing or mounting wheels• Hexagon 17, 19 & 21 mm• For use with a impact gun• Protective plastic sleeve for working on
Completely new, unique hydraulic spring compressor with a wide range of applications
Hydraulic Spring Compressor with Hydraulic Foot Pump including 4 Spring Plates Ø 70 - 160 mm
Hub Puller Commercial VehiclesKingpin ToolUniversal kit for replacing the Kingpin
The tool is flexible and fits heavy trucks/busses with 8 bolt 275 mm and 10 bolt 335 mm. The robust design allows to combine the full power of 32 ton with punching with a hammer during pressing out the hub.
• Is used together with a 32-ton hydraulic cylinder with impact function
• No removal of the shaft required• Easy to use• It is also suitable for buses
• Is used together with a 32 ton impact resistend hydraulic cylinder
Pneumatic Hydraulic Foot Pump Pneumatic Hose Kit with Air GunPneumatically driven hydraulic pump (700 bar)
for use with hydraulic cylinders Hose kit which on 80255550 is mounted so that an air gun can be attached on the hydraulic hose for pulling back of the hydraulic cylinder.
• Oil tank capacity: 1.4 litres• 2.2 m hose• Drip-free quick coupling
Hydraulic Cylinder
32 ton
22 ton
8,5 ton
Press and pull hydraulic cylinder. The cylinder´s hydraulic pressure can be combined with impact force when using the punching socket.
Drain Plug Key Set 17 pcsEquipped with triangular-, square-, hexagonal-and spline sockets. Drive ⅜“
Drain Plug Thread Repair Kit M13, M15, M17 & M20
Universal repair kit to fit oversize drain plugs in damaged oil pans.
• With thread-cutting tools and seals• Plug sizes M13, M15, M17 and M20
Oil Filter Wrench
Petrol: 60 – 80 mmDiesel: 80 – 110 mm
• Leftward orientated teeth for reliable release• Can also be used with a damaged sheet metal hex• Flexibly adjusted
Universal, Commercial vehicles104 – 150 mm
Commercial vehicle 104 – 150 mm
Oil Filter Wrench Ford DW enginesSimple and time-saving removing and installing of the, because of diesel particulate filter system, difficult to reach filter housing
For safe drilling of broken off studs with thread sizes M6 - M10
Thread Repair KitFor improving the strength of threads in materials with low shearing strength, e.g. aluminium and magnesium alloys and for thread repair of damaged or worn threads
• Including 110 thread inserts• Narrow and exact tolerances• Optimizing the thread properties• Reject recovery
Universal Drill Guide
• Guide rails enable accurate centering of the drill guide• Including short positioning rail for limited work spaces
Passage Socket Set Extra Long/Deep
• For hard to reach nuts and bolts• SW: hex 8, 10, 11, 12, 13 & 14• ⅜“ -Drive
Bolt Twister size 2 – 10Sockets of high-strength special steel with a self locking, conical special profile. For removing screws with damaged Allen and XZN profiles
• ⅜“ -Drive • Size 2 for M5 • Size 3 for M6• Size 4 for M8
Twist-Sockets Size 1Sockets of high-strength special steel with a self locking special profile. For releasing of bolts, nuts, wheel locks and Allen screws whose drive profiles are damaged, e.g. overwound hexagonal profiles.
• 10 - 19 mm• ⅜“-Drive
• Size 6 for M10 - M12• Size 8 for M14 - M16• Size 10 for M18 - M20
Twist Socket Set LongQuick and sure release of defective screws. The innovative spiral profile gripes deep during an anticlockwise use into the screw head and makes an unscrewing possible.
• ½“-Drive • Sizes: 17, 19, 21 & 22 mm
Spiral Drill HSS Extra Long Precision GroundIndustrial quality for drilling alloyed and unalloyed steels, cast iron, malleable iron, copper alloys, silver, graphite and sintered iron
• Long version - DIN 340 RN• Special grinding: No centre punch required,
less feeding pressure required
Available in sizes from Ø 0.6 mm to Ø 20 mm
Precise and spot-drilling
Suited for: e.g. MB E-Class W212, rear bumper removal, C-class W204, front door hinge, A-pillar inside
• High-quality high-speed steel• Precise and spot-drilling
• Self-sealing and self-locking• Max. Operating pressure: 15 bar• Quickly and easily filling or venting• One-hand operation without force
Brake Calliper Bleeder Valve Repair SetFor drilling out and replacing torn bleeder valves.
Suited for: universal e.g. Audi, VW, Opel brake callipers
Protective Cap Puller PliersFast and damage-free removal of plastic wheel bolt caps.
• Extra slim gripper arms for t ight wheel bolt shafts
Universal
Clamp Locking PliersFor clamping hoses, without these being damaged. A valuable help with the repair of motor-vehicle brake systems and cooling systems.
• Firm grip on small objects
Ozone Maker for DisinfectionThe effect of ozone is used for removing mould, bacteria and dust mites from the vehicle interior.
• For car preparation• Eliminates bad odours• Disinfects
Storage TableA folding tray table made of galvanized iron for e.g. body parts and the like.
• Height adjustable• Space-saving storage• Weight: 11 kg
Scraper and Chisel Set 4-piece
This tool set can be used both as a scraper and as a chisel.
• Ideal for removing stickers, stickers, adhesive residues, seals, etc.
• For cutting and chiselling of sheet metal and even welding points
Dosage Hand Pump 1000 mlFor controlled extracting and filling of liquids
• Exact dosage because of the easy to read scale• Universal useable
Plastic Hose 300 mmFor Dosage Hand Pump
Manual Tire Inflator with Valve CouplingErmöglicht das Prüfen des Reifendruckes und das Befüllen des Reifens.
• Handy grip with 2-stage inlet lever allows for optimal handling• Gauge 0 - 10 bar/145 psi, Ø 80 mm with protective rubber cap