This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
SERVICE MANUAL
Sony CorporationPersonal Audio GroupPublished by Sony Engineering Corporation
continuousLaser Output: Less than 44.6 µW(This output is the value measurement at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block with 7 mm aperture)
Frequency response 2 Hz – 20 kHz (±0.5 dB)Signal-to-noise ratio More than 90 dBDynamic range More than 90 dB
(50 kHz step)Antenna FM lead antennaAntenna terminals 75 ohms unbalancedIntermediate frequency 10.7 MHz
AM tuner sectionTuning rangeRussian model: 531 – 1,602 kHz (with the
tuning interval set at 9 kHz)
Other models: 530 – 1,710 kHz (with the tuning interval set at 10 kHz)531 – 1,602 kHz (with the tuning interval set at 9 kHz)
Antenna AM loop antennaAntenna terminals External antenna terminalIntermediate frequency 450 kHz
2
CX-JDS30
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.
• AbbreviationE51 : Chilean and Peruvian modelsMX : Mexican modelRU : Russian model
Model Part No.
MX model 2-595-344-0[]
E51 model 2-595-524-0[]
RU model 2-599-604-0[]
MODEL IDENTIFICATION– BACK PANEL –
3
#
#
3
Part No.
GeneralPower requirementsRussian model: 230 V AC, 50/60 HzMexican model: 127 V AC, 60 HzOther models: 120 V, 220 V or
230 – 240 V AC, 50/60 HzAdjustable with voltage selector
Power consumption 245 watts
Dimensions (w/h/d) (excl. speakers):Approx. 230 × 365.5 ×409 mm
Mass (excl. speakers) Approx. 9.1 kg
Design and specifications are subject to change without notice.
3
CX-JDS30
The laser diode in the optical pick-up block may suffer electrostaticbreak-down because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.
NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objective lens.
NOTES ON HANDLING THE OPTICAL PICK-UPBLOCK OR BASE UNIT
Notes on chip component replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing• Keep the temperature of the soldering iron around 270 °C
during repairing.• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardous radiationexposure.
UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARKUnleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higherthan ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350 °C.Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc.
• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.
Laser component in this product is capable of emitting radiationexceeding the limit for Class 1.
This appliance is classified as a CLASS 1 LASER product.The CLASS 1 LASER PRODUCT MARKING is located on theexterior.
The release method of a CD disc tray LOCK function
There is a disc lock function for the disc theft prevention for ademonstration at a shop front in this machine.Procedue:
1. Press the ?/1 button to turn the set on.2. Press two buttons of x and Z simultaneously for five
seconds.3. The message “LOCKED” is displayed and the tray is
locked. (Even if exiting from this mode, the tray is stilllocked.)
4. Press two buttons of x and Z simultaneously for fiveseconds again.
5. The message “UNLOCKED” is displayed and the tray isunlocked.
6. To exit from this mode, press the ?/1 button to turn theset off.
4
CX-JDS30
TABLE OF CONTENTS
1. GENERAL ................................................................... 5
2. DISASSEMBLY2-1. Disassembly Flow ........................................................... 72-2. Top Panel, Side Panel ...................................................... 82-3. Front Section ................................................................... 82-4. CD Mechanism Section ................................................... 92-5. Cassette Mechanism Deck, DS-PAI/HP/MIC Board ...... 92-6. DS-PANEL Board ........................................................... 102-7. Rear Cabinet .................................................................... 102-8. Power Trans ..................................................................... 112-9. DS-MAIN Board, Heat Sink ........................................... 112-10. Holder (CD Mech) ........................................................... 122-11. Base Unit (BU-F1BD81AA), CD Mech ......................... 122-12. BD Board, Optical Pick-up (KSM-215DCP/C2NP) ....... 132-13. Frame ............................................................................... 132-14. Belt .................................................................................. 142-15. Cassette Panel .................................................................. 15
3. TEST MODE ............................................................... 16
2 Press . or > repeatedly to select “CLOCK SET”, then press ENTER.
3 Do the same procedures as step 3 to 6 above.
Notes The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
You cannot set the clock in Power Saving Mode (page 25).
Setting the clock
7
CX-JDS30SECTION 2
DISASSEMBLY
2-1. DISASSEMBLY FLOW
• This set can be disassembled in the order shown below.
SET
2-2. TOP PANEL, SIDE PANEL(Page 8)
2-15. CASSETTE PANEL(Page 15)
2-3. FRONT SECTION(Page 8)
2-7. REAR CABINET(Page 10)
2-10. HOLDER (CD MECH)(Page 12)
2-14. BELT(Page 14)
2-8. POWER TRANS(Page 11)
2-11. BASE UNIT (BU-F1BD81AA), CD MECH(Page 12)
2-4. CD MECHANISM SECTION(Page 9)
2-6. DS-PANEL BOARD(Page 10)
2-5. CASSETTE MECHANISM DECK, DS-PAI/HP/MIC BOARD
(Page 9)
2-9. DS-MAIN BOARD, HEAT SINK (Page 11)
2-13. FRAME(Page 13)
2-12. BD BORD, OPTICAL PICK-UP(KSM-215DCP/C2NP)
(Page 13)
8
CX-JDS30
Note: Follow the disassembly procedure in the numerical order given.
2-2. TOP PANEL, SIDE PANEL
2-3. FRONT SECTION
qa top panel
2 two screws(+BVTP 3 × 10)
5 two screws(+BVTP 3 × 10)
7 three screws(+BVTP 3 × 10)
3 right panel
6 left panel
1 four screws(Case 3)
4 four screws(Case 3)
q;
9
8
9 front section5 three screws(+BVTP)(B3)
6 screw(+BVTP)(B3)
8 screw(+BVTP)(B3)
7 screw(+KTP 3 × 6)
1 wire (flat type) (11core) (CN112)
2 wire (flat type) (15core) (CN604)
4 wire (flat type) (27core) (CN605)
3 connector (6p) (cassette deck)
9
CX-JDS30
2-4. CD MECHANISM SECTION
2-5. CASSETTE MECHANISM DECK, DS-PAI/HP/MIC BOARD
1 two screws(+BVTP)(B3)
2 CD mechanism section
2 wire (flat type) (8core)
1 three screws(+PTP)(B2.6)
3 three screws(+PTP)(B2.6)
5 two screws(+PTP)(B2.6)
6 holder (PWB MIC)
7 DS-PAI/HP/MIC board
4 cassette mechanism deck
10
CX-JDS30
2-6. DS-PANEL BOARD
2-7. REAR CABINET
1 knob (RTRY)
3 knob (RTRY AMS)
2 guide (LED VOL)
4 twenty screws (+PTP)(B2.6)
6 DS-PANEL board
3 connector (11p) (CN651)
2 wire (flat type) (11core)
1 connector (2p) (CN871) 3 four screws
(+BVTP)(B3)
4 rear cabinet
11
CX-JDS30
2-8. POWER TRANS
2-9. DS-MAIN BOARD, HEAT SINK
1 four screws
3 power trans
2 cord bushing
5 DS-MAIN board
4 connector
6 heat sink
1 two screws(+BVTP)(B3)
3 screw(+BVTP)(B3)
2 two screws(+BVTP)(B3)
12
CX-JDS30
2-10. HOLDER (CD MECH)
2-11. BASE UNIT (BU-F1BD81AA), CD MECH
2 wire (flat type) (27 core) (CN606)
4 wire (flat type) (15 core)
3 tape
5 screw (+BVTP 2.6 × 8)
6 DS-CONN board
7 holder (CD MECH)
1 four screws (+BVTP 2.6 × 8)
2 two coil springs (insulator)
4 two coil springs (insulator)
1 two floating screws (+PTPWH M2.6)
3 two floating screws (+PTPWH M2.6)
6 base unit (BU-F1BD81AA)
7 tray panel
8 CD mech
5 wire (flat type) (27 core)
13
CX-JDS30
2-12. BD BOARD, OPTICAL PICK-UP (KSM-215DCP/C2NP)
6 two insulators
7 two insulators
2 gap tube5 BD board
8 optical pick-up (KSM-215DCP/C2NP)
1 screw (+BVTP 2.6 × 8)
4 Remove the four solderings of motor.
3 wire (flat type) (16 core)
2-13. FRAME
1 four screws
2 frame
14
CX-JDS30
2-14. BELT
2 Slide the upper-most tray foward the front.
1 Release the hook of the tray.
3 While pushing up the plate cam, draw the Drawer (three trays) entirely foward front.
4 two belts
plate cam
15
CX-JDS30
2-15. CASSETTE PANEL
4 cassette panel
1
2
3 two claws
16
CX-JDS30SECTION 3TEST MODE
[COLD RESET]* The cold reset clears all data including preset data stored in
the RAM to initial conditions. Execute this mode whenreturning the set to the customer.
Procedure:1. Press the ?/1 button to turn the set on.2. Press three buttons x , X and [i-Bass] simultaneously.3. The fluorescent indicator tube does not display any message
and the set is reset.
[Version Display Mode]* The version of the microcomputer is displayed.
Procedure:1. Press the ?/1 button to turn the set on.2. To enter the test mode, press three buttons x , [DISPLAY]
and ?/1 simultaneously. The version of the microcomputeris displayed.
[PANEL Test]* All fluorescent segments are tested.
Procedure:1. Press the ?/1 button to turn the set on.2. Press three buttons x , [DISPLAY] and ?/1 simultaneously.3. Then all segments of the florescent indicator tube are turned
on.
[KEY Test]* Keyboard check
Procedure:1. When the panel test mode is activated. Press x and [DISC 1]
buttons simultaneously, and the key check mode is activated.2. The message “KEY 0 0 0” is displayed.3. Press x , and [DISC 1] buttons simultaneously, and the key
count mode is activated.4. The message “KEYCNT 0” is displayed.
Each time a button is pressed, “KEYCNT 0” value increased.However, once a button is pressed, it is no longer take intoaccount.
[CD Ship (LOCK) & COLD RESET MODE]Procedure:
1. Press the ?/1 button to turn the set on.2. Select the function “CD”.3. Press the ?/1 button to turn the set off.4. Press three buttons x , [i-Bass] and [DISC 3] simultaneously.5. The “LOCK” display blinks instantaneously and CD ship mode
is set.6. The Cold Reset Mode is set.
[CD Ship Mode]* This mode moves the optical pick-up to the position durable
to vibration. Use this mode when returning the set to thecustomer after repair.
Procedure:1. Press the ?/1 button to turn the set on.2. Set the FUNCTION to CD.3. Press three buttons x , ML and [DISPLAY] simulta-
neously for more than two seconds.4. After a message “LOCK” is displayed on the fluorescent
indicator tube, the CD ship mode is set and the power is turnedoff.
[Disc Tray Lock]The disc tray lock function for the antitheft of an demonstrationdisc in the store is equipped.Setting Procedure :
1. Press the ?/1 button to turn the set on.2. Press two buttons of x and Z simultaneously for five
seconds.3. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :1. Press two buttons of x and Z simultaneously for five
seconds again.2. The message “UNLOCKED” is displayed and the tray is
unlocked.Note : When “LOCKED” is displayed, the tray lock is not released
by turning power on/off with the ?/1 button.
[Common Test]* This mode is used to check the function of the amplifier.
Procedure:1. Press the ?/1 button to turn the set on.2. Press three buttons x , [DISPLAY] and ?/1 simultaneously.3. The message “Volume MAX” is displayed, when the
[VOLUME] knob is rotated clockwise. The message “VolumeMIN” is displayed, when the [VOLUME] knob is rotatedcounterclockwise.
4. Each time the [BASS] , [TREBLE] and [MIDDLE] knob is turned,the message “EQ MAX”, “EQ MIN” or “EQ FLAT” isdisplayed in this order.
[AM Channel Step 9 kHz/10kHz Selection Mode]* Either the 9 kHz step or 10 kHz step can be selected for the
AM channel step. (EXCEPT AEP,UK,RU)Procedure:
1. Set the FUNCTION to AM.2. While depressing the [PLAY MODE/TUNING MODE] button,
press the ?/1 button.3. The channel step is changed over.
[CD Repeat 5 Times Limit Release Mode]Procedure:
1. Press the ?/1 button to turn the set on.2. Select the FUNCTION to CD.3. Press three buttons x , [DISPLAY] and [DISC 1] simulta-
neously.4. The repeat all mark blinks and then repeat 5 times limit is
released.
17
CX-JDS30
2.94 – 7.84 mN • m(30 to 79 g • cm)
(0.42 – 1.11 oz • inch)0.15 – 0.59 mN • m
(2 to 6 g • cm)(0.03 – 0.08 oz • inch)
2.94 – 7.84 mN • m(30 to 79 g • cm)
(0.42 – 1.11 oz • inch)0.15 – 0.59 mN • m
(2 to 6 g • cm)(0.03 – 0.08 oz • inch)6.86 – 17.64 mN • m
(70 to 179 g • cm)(0.98 – 2.49 oz • inch)0.98 mN • m or more
(10 • cm or more)(0.14 oz • inch or more)
0.98 mN • m or more(10 • cm or more)
(0.14 oz • inch or more)
CQ-102C
CQ-102C
CQ-102RC
CQ-102RC
CQ-201B
CQ-403A
CQ-403R
TAPE MECHANISM DECK SECTIONPrecaution
1. Clean the following parts with a denatured alcohol-moistenedswab:
record/playback heads pinch rollerserase head rubber beltscapstan idlers
2. Demagnetize the record/playback head with a head demag-netizer.
3. Do not use a magnetized screwdriver for the adjustments.4. After the adjustments, apply suitable locking compound to
the parts adjusted.5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque Measurement
Mode
FWD
FWD
back tension
REV
REV
back tension
FF/REW
FWD tension
REV tension
Torque meter Meter reading
Record/Playback Head Azimuth AdjustmentProcedure:
1. Mode : Playback
2. Turn the adjustment screw and check output peaks. If the peaksdo not match for L-CH and R-CH, turn the adjustment screwso that outputs match within 1 dB of peak.
DECK SECTION 0 dB=0.775V
Precaution1. Demagnetize the record/playback head with a head
demagnetizer.2. Do not use a magnetized screwdriver for the adjustments.3. After the adjustments, apply suitable locking compound to
the parts adjusted.4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.5. The adjustments should be performed in the order given in
this service manual. (As a general rule, playback circuitadjustment should be completed before performing recordingcircuit adjustment.)
6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwisespecified.
• Test Tape
Signal Used forTape
P-4-A100
WS-48B
10 kHz, –10 dB
3 kHz, 0 dB
Azimuth Adjustment
Tape Speed Check
SECTION 4MECHANICAL ADJUSTMENTS
SECTION 5ELECTRICAL ADJUSTMENTS
set
DS-MAIN boardSPEAKER terminal (J171)L-CH, R-CH
+–
level meter
test tapeP-4-A100(10 kHz, –10 dB)
Screwposition
L-CHpeak
within1dB
Outputlevel
L-CHpeak
R-CHpeak
within1dB
Screwposition
R-CHpeak
18
CX-JDS30
4. After the adjustments, apply suitable locking compound tothe parts adjusted.
Adjustment Location: Record/Playback/Erase Head
3. Mode: Playback
set
test tapeP-4-A100(10 kHz, –10 dB)
R-CH
oscilloscope
L-CH
R-CH
V H
waveform of oscilloscope
in phase 45° 90° 135° 180°
good wrong
DS-MAIN boardSPEAKER terminal (J171)L-CH
Tape Speed CheckMode: Playback
1. Insert the WS-48B into deck.2. Press the nN button of deck.3. Confirm that the frequency counter reads 3000 ± 90 Hz.
Sample Value of Wow and flutter: 0.3% or less W.RMS (JIS)(WS-48B)
+–
set
test tapeWS-48B (3 kHz, 0 dB)
DS-MAIN boardSPEAKER terminal (J171)L-CH, R-CH
frequency counter
Record Bias AdjustmentProcedure:
1. Record mode
2. Mode: Playbacki-Bass OFFBASS 0TREBLE 0
3. Confirm playback the signal recorded in step 1 becomeadjustment level as follows.
Adjustment level: Playback output of 315 Hz to playback outputof 10 kHz: –2 ± 3.0 dB (0 ± 4.5mV).
attenuator
set
DS-MAIN boardAUX IN (J552)
1) 315 Hz2) 10 kHz 50 mV (–23.8 dB)
600 Ωblank tape CN-123
AF OSC
+–
set
recordedportion
DS-MAIN board speaker terminal (J171)
level meter
Note: Refer to “2-15. Cassette Panel” (see page 15)
adjustment screw
19
CX-JDS30
CD SECTION
Note:1. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.2. Use an oscilloscope with more than 10MΩ impedance.3. Clean the object lens by an applicator with neutral detergent
when the signal level is low than specified value with thefollowing checks.
S-curve CheckConnection:
Procedure:1. Connect an oscilloscope to test point TP (FEO) and TP (VC)
on the BD board.2. Set the FUNCTION to “CD”.3. While depressing the nN button, insert an AC plug.4. Put the disc (YEDS-18) in and press the x button and actuate
the focus search. (actuate the focus search when disc table ismoving in and out)
5. Check the oscilloscope waveform (S-curve) is symmetricalbetween A and B. And confirm peak to peak level within 2 ± 1Vp-p.
Note: • Try to measure several times to make sure than the ratio of A : Bor B : A is more than 10 : 7.
• Take sweep time as long as possible and light up thebrightness to obtain best waveform.
Checking Location: BD board (Side B)(See page 20)
RFDC Level CheckConnection:
Procedure:1. Connect an oscilloscope to test point (RFDCO) and TP (VC)
on the BD board.2. Turn the power on.3. Put the disc (YEDS-18) in to playback the number five track.4. Confirm that oscilloscope waveform is clear and check RFDC
signal level is correct or not.Note: A clear RFDC signal waveform means that the shape “◊” can
be clearly distinguished at the center of the waveform.
Checking Location: BD board (Side B)(See page 20)
RFAC Level CheckConnection:
Procedure:1. Connect an oscilloscope to test point TP (RFACO) and TP
(VC) on the BD board.2. Turn the power on.3. Put the disc (YEDS-18) in to playback the number five track.4. Confirm that oscilloscope waveform is clear and check RFAC
signal level is correct or not.Note: A clear RFAC signal waveform means that the shape “◊” can
be clearly distinguished at the center of the waveform.
Checking Location: BD board (Side B)(See page 20)
+–
BD board
oscilloscope
TP (FED)TP (VC)
S-curve waveform
symmetry
A
B
within 2 ± 1 Vp-p
+–
BD board
oscilloscope
TP (RFDCO)TP (VC)
RFDC signal waveform
VOLT/DIV: 200 mVTIME/DIV: 500 ns
level: 0.6 ± 0.15 Vp-p
+–
BD board
oscilloscope
TP (RFACO)TP (VC)
RFAC signal waveform
VOLT/DIV: 200 mVTIME/DIV: 500 ns
level: 1.0 ± 0.4 Vp-p
20
CX-JDS30
E-F Balance AdjustmentConnection:
Procedure:1. Connect an oscilloscpe to test point TP (TEO) and TP (VC)
on the BD board.2. Set the FUNCTION to “CD”.3. AC is put in pushing nN button to enter the CD test mode.4. Put the disc (YEDS-18) in to playback the number five track.5. Press the nN button. If it plays, press the nN button
again. (The tracking servo and the sledding servo are turnedOFF)
6. Check the level B of the oscilliscope’s waveform and the A(DC voltage) of the center of the Traverse waveform.Confirm the following :A/B x 100 = less than ±10%
7. Press the nN button. (The tracking servo and sleddingservo are turned ON)
8. To exit from this mode, turn the power off.Notes: • Always move the optical pick-up to most inside track when exiting
from this mode. Otherwise, a disc will not be unloaded.• Do not run the sled motor excessively, otherwise the gear can be
chipped.
Checking Location: BD board (Side B)
Checking Location:
– BD BOARD (Side B) –
+–
BD board
oscilloscope
TP (TEO)TP (VC)
Traverse Waveform
0V
Center of the waveform
B
A (DC voltage)
level: 1.0 ± 0.5 Vp-p
Traverse Waveform
0V
Tracking servoSled servo
OFF
Tracking servoSled servo
ON
C (DC voltage)
IC251
IC301
IC101
IC303
TP(RFACO)
TP(VC)
TP(FEO)
TP(RFDCO)
TP(TEO)
2121
CX-JDS30
CX-JDS30
For Schematic Diagrams.Note:• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics andtantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.• f : internal component.• C : panel designation.
• A : B+ Line.• B : B– Line.• H : adjustment for repair.• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal productiontolerances.No mark: CD STOP
• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal productiontolerances.
• Circled numbers refer to waveforms.• Signal path.
F : TUNERJ : CDd : AUXE : PB (TAPE)a : REC (TAPE)N : MIC
For Printed Wiring Boards.Note:• X : parts extracted from the component side.• : Pattern from the side which enables seeing.
• Indication of transistor.
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printed in each block.)
C
B
These are omitted.
E
Q
B
These are omitted.
C E
Note: The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
Caution:Pattern face side: Parts on the pattern face side seen from(Side A) the pattern face are indicated.Parts face side: Parts on the parts face side seen from(Side B) the parts face are indicated.
SECTION 6DIAGRAMS
• Circuit Boards Location
DS-CONN board
DS-PANEL board
DS-AMPLIFER board
BD board
DS-POWER board
DS-PAI/HP/MIC board
DS-MAIN board
DS-VOL board
• Waveforms– DS-PANEL Board –
1 IC604 0 (XCIN)
1.2 Vp-p
500 mV/DIV, 10 µs/DIV
2 IC604 qg (XIN)
1 V/DIV, 40 ns/DIV
30.4 µs
2.3 Vp-p62.5 ns
2222
CX-JDS30
CX-JDS30
6-1. BLOCK DIAGRAM – MAIN SECTION –
: TUNER
: CD
• Signal Path
• R-CH is omitted due to same as L-CH.
: AUX
: PB (TAPE)
: REC (TAPE)
: MIC
BIASOSC
+VL
ERASEHEAD
REC/PBHEAD
DECK BLOCK
42
40
SYSTEM CONTROLLERIC604 (1/2)
43
J171SPEAKER
R-CH
RY171
L
R
FUNCTIONKEY
S611-619
TUNER PACK
L-CH
L-CH
R-CH
R-CH R-CH
DODI
CLK
CE
TUNED
R-CH
26
REC/PBSWITCH
Q502-504
L501BIAS OSC
Q501
Q627,628
Q623,624
Q621,622
CDMOTOR
CONTROL
MOTORDRIVE
MOTORDRIVE
MOTORDRIVE
MOTORDRIVE
Q619,620,625,626
IC551MIC AMP
DC 7V
MICOVERLOAD
DET
Q551,552
PLAY
VR501
R REC
F REC
PACKEND
DECKMOTOR
Q629,631
25
57
38
FUNCTIONKEY
FUNCTIONKEY
S621-629
90
89
S601-609
91
45
+9V
J552AUDIO IN
SELECTORIC401
POWER AMPIC301
31 28
33
2
35
27 R-CH
24
27STEREO
TU-MUTE 23
R-CH
R OUT R-CHL OUT
58
50
53
51
48
49
R-CH J551PHONES
LCD
IC601LCD DRIVER
+Vcc
3CD MECHA
I CD_CSW3
I CD_CSW1
I CD_CSW2
M1
+M1
–M1
M2
+M2
–M2
Q505,506
BIASSWITCH
Q507-510
VM(+10V)
24
59
56
55
54
M
M
40
8
9
18
39 19
23
26
25
Q361(Q261)
Q303,305,306 (Q203,205,206)
22
87
OVERLOADDET
TH361
PROTECTDET
Q151-153FAN
DRIVE
Q871-873
VM
R-CH
FAN
R-CH
37
36
S651
95
74
S652
LEDCONTROL
Q618, Q630
97
LED607STAND BY
LED608i-BASS
10
11
X60132.768kHz
15
13
47
X60216MHz
D101
D102
Q801,803
3.3VREG
IC102
D119-117,214
D116
D114
+VH
-VH
+VL
-VL
VM(+10V)
TU9V
CD 7V
D VDD(3.3V)
A VDD(3.3V)
MP3VD
D154
D152
D155
D153
D156
D158
21
IC602
7 31
RESETSWITCH
SWITCHQ606
Q605
12
IC603
uCON +B
13
204
94
100
1
5
2
V STBYD602IC605
54
BD SECTION
P95
P81
P90
P82/INT12
RES
P93
P92
P102/AN2
P97
P96
P53
P54P56P74
P80
P01/AN01
P63/TXD0
P61/CLK0
P107/AN7
P16/INT4
P106/AN6
P105/AN5
P101/AN1
P100/AN0
P00/AN00
P02/AN02
P07/AN07
P51
P42
P62/RXD0
P77
P75
P76
P33
P34P35
P36
P37
P40
P41
P44
P43
P46
P45
P47
P52
P73/CT52
P84/INT2
P60/CTS0
P57/CLKOUT
44
18
35 7
8
930
13
43
LEDDRIVE
Q613
LEDDRIVE
Q614
52
XC IN
XC OUT
X IN
X OUT
AUX-L OUT-L
B1
PBIP
C1
OUT-R
BB1
BB1
BB2BB2
REC10
VOL1
VOL2
SD
SC
REMOTECONTROLRECEIVER
RESET
A
D157
RDSDATA
RDSINT
RU
LEDDRIVE
Q608-610,615-617
88
11 LI+
13
ST-B
Y
5
THERMALDET
Q362
Q301
D155
Q874
IC101
1210VREG
D001,002
RELAYDRIVE
Q102
D111
D112-27VREG
+9VREG
-VFL(-27V)
Q101
PT002POWER TRANSFORMER
FL1
FL2
RY002
D003
VM (+10V)MIC 1
J553
MIC 2
J554
2
MOTORDRIVE
Q607,611
T SOLDRIVE
Q604,612M
MECHA BLOCK
3
1
7
65
SW7 (CHACK)
SW6 (CLOSE)
SW5 (STOC)SW8 (OPEN)
86
81
+3.3VREG
LED601-606
RTRYAMS
RTRYVOLUME
-VFL
+3.3V
FL601LCD
DINV
CLK
STB
VEEVDD
VDD
SEG1
SEG19
GR1
GR9
MUTECONTROL
AMPCONTROL
Q401,403
BASS-AGCCONTROL
LO+
LO-
4
Q366,367
AMPPROTECT
FAN CURENTDETECT
29
14
33
31
34
42
AC IN
PT902
(SUB)TRANSFORMERPOWER SW901
VOLTAGESELECTOR
E51
EXCEPT E51
2323
CX-JDS30
CX-JDS30
– BD SECTION –
: CD
• Signal Path
MP3STB
MP3REQMIACKMICKMIDIO
MILP
MICS
MP3RST
SCOR
SENSCLOCK
XLT
DATA
XRST
XTACN
LOUT
ROUT
DOUT
A MAINSECTION
OPTICAL PICK-UPBLOCK
(KSM-215DCP/C2NP)
LDDRIVER
Q10
+1.7V+3.3V
LD
GND
FOCUSCOIL
F+
F
T+
TTRACKING
COIL
IC251
SW101
X17116.9MHz
+3.3V
SL/SP MOTORDRIVER
IC101RF AMP
16
7
15
17
18
VR
PD
19
20
21
22
5
9
3
24MUTE
CH2OUT-F
CH1FIN
CH1RIN
CH2FIN
SFDR
OPIN+
CH2OUT-R
CH1OUT-R
CH1OUT-F
CH4OUT-F
CH4OUT-R
CH3OUT-R
CH3OUT-F
M
M
M101(SPINDLE)
M102(SLED)
VCC
VC
A
B
C
D
E
F
DETECTOR
A
B
E19
F20
LD36
PD37
TFDR11
SSTP7
FFDR13
CH3FIN30
MPD6
95XTACN
100XRST
102DATA
104XLAT
105CLOCK
86AOUT2
81AOUT1
71DOUT
61PCMD1
62LRCK1
63LRCK
65PCMD
DIGITAL SIGNALIC301
PROCESSOR
SYSTEM CONTROLLERIC604(2/2)
21
40
SDO011
LRCKIA16
SFSY/LRCK1B19
SDIO14
77 XTAO
78 XTAI
55VDD
VDD
VDDM
26
27
C28
D29
107SENS
XTACN
XRST
DATA
XLAT
CLOCK
SENS
113GFS
114C2PO
2
3
1
FOK
TRDR12
10SRDR CH3RIN29
CH2RIN FRDR14
66BCK
60BCK1
BCKIA15
SBSY/BCK1B18
6
3.3V
IC303
8
5 1
3 P26
P25
P27
P24
P30
P31
P72/CLK2
P71/RXD2
P22
P32
P67/TXD1
P23
P66/RXD1P83/INT1
P65/CLK1
36
87
6
4
5
2
66
67
6528
29
63
68
61
19
3233
69
70
31
60
115SCOR SCOR
REG
2424
CX-JDS30
CX-JDS30
6-2. PRINTED WIRING BOARD – BD SECTION – • See page 21 for Circuit Boards Location. :Uses unleaded solder.
• SemiconductorLocation
Ref. No. Location
IC101 D-7IC251 C-6IC301 C-7IC303 B-8
Q10 E-4
SLEDMOTOR
SPINDLEMOTOR
13
54
64
11617
32
33 4849
S101(LIMIT)
M
M
TP(VC)
TP(TEO)
TP(FEO)
TP(RFDCO)
TP(RFACO)21
212121
(page 32)CN605BOARD
DS-CONN
OPTICALPICK-UPBLOCK
(KSM-215DCP)
I
IC251
IC301
IC303
IC101
1 2
A
B
C
D
E
F
3 4 5 6 7 8 9
2525
CX-JDS30
CX-JDS30
6-3. SCHEMATIC DIAGRAM – BD SECTION – • See page 38 for IC Block Diagrams. • See page 40 for IC Pin Function Description.
IDS-CONNBOARDCN605
(Page 33)
TP165
TP166
TP178
TP14
4
TP14
7
TP15
3
TP186
TP187
TP167
TP16
0
TP16
2
TP177
TP14
5
TP14
8
TP12
1
TP12
2
TP12
3
C305
JPO004
JPO10
TP25
0
TP301
TP302
TP303
TP304
TP103
TP104
TP105
TP14
6
R161
R16
3
R351
R352
R353
R354R401
R402
R403
R404
R405
R406
R407
R408
R409
R411
R412
R419
R11
R19
1
R13
2
R251
R253
R12
R14
2
R14
3
R10
JPO102
JPO103
M101
S101
C15
C17
C115
C116
C12
2
C125
C132
C13
3
C134
C141
C142
C143
C151
C161
C181
C194
C201
C203
C252
C255
C25
7
C303
C306
C308
C309
C310
C311
C312
CN101
R12
1
R171C171C313
C314
C183
C184
TP420
TP421
TP422
TP423
TP424
R252
TP42
5
TP42
6
C259
TP427
TP428
TP429
TP430
TP431
TP432
R13
Q10
C16
C12
3
C260
R172
C124
R13
3
R313
TP433
TP436
C316
C10C11
C162
C317
C315
C307
TP401
TP407
TP406
TP405
TP404
TP403
TP402
TP408
TP410TP434
TP417
TP416
TP415
TP414
TP413
TP412
TP419
TP411
TP435
TP409
TP19
TP18
TP17
TP16
TP15
TP102
TP14
TP13
TP12
TP11
TP10
C195
C182
C174
R13
1
C13
1 C18
R301
FB301
R303
R182
R181
X171C172
R173
R203
IC303
R302
R162
R16
5
C211
C210
C212
R15
1
R205
R410
C320
C213
CN201
C185
C186
C163
C19
6
C318
R30
6
IC251
C258
C251
C302
M102
TP25
3
TP25
2
TP25
1
C111
R112
R114
R111
R113
C112
C113
C114
C209
R305
IC301
R14
1
IC101
R307
TP12
5
TP12
4
TP14
2
TP14
9
R204
R20
1
MIRR
DFCT
FOK
XU
GF
XP
CK
GFS
MVDD
MGND
LOCK
WD
CK
CO
UT
VC
WFC
K
SB
SO
RFD
CO
2204V
MDP
APC
SP-
LRCK
PCMD
BCK
C2P
O
100
100
100
100
100
100100
100
100
100
100
100
100
100
100
100
100
100
0
0
10k
10k
10k
100k
1k
3.3k
3.3
FEI
TEI
SW
0.1F
2204V
0.1 F10010V
0.1 B
0.1 F
0.47
B
0.01
B
0.1 F
0.1
B
0.00
15B
0.1 F
10010V
0.1 F
0.1 F
0.1F
10010V
10010V
0.1 F
0.1 F
0.1
F
0.1F
0.1 F
474V
0.1 F
0.1 F
0.1 F
0.1 F
16P
15k
0.1 F
47 4V
22 6.3V
22 6.3V
AGND
DGND
MP3GND
IOP1
IOP2
22k
SW+
SW-
PCMDI
FRDR
FFDR
TRDR
TFDR
MDP
1
2SB1690K
1F
0.1
B
220 10V
330p
CH
180k
220
MP3VDD
AVDD
0.0022 B
106.3
B
106.3
B
0.1 F
0.01 B
0.1 B
0.1 F
MP3STB
MICS
MILP
MIDIO
MICK
MIACK
MP3REQ
MP3RST
ROUTAVDD
SCOR
SENS
CLK
XLT
DATA
XRST
XTCN
LOUT
DVDD
DOUT
F-
T-
F-
F+
PD
F
C
B
A
D
E
0.1 F
0.1 F
0.1 F
1M100p
CH
0.001 B
100k
100k
100
100
0
0
BH15FB1WG
10k
47k
220p CH
0.1 B
22p CH
0
0
100
0
22p CH
470p CH
470p CH
0.1 0.1
0.01B
0
0.0068B
0.1F
SL-
SL+
SP+
0.0033 B
15k
15k
1k
1k
470p
0.0033
470p B
0.01
B
100k
TC94A34FG-002
4.7k
CXD3059AR
10k
RFA
CI
RFA
CO
EXC
K
0
0
47022p CH
0.1F
1M16.9MHz27p CH
0
27P
BA5947FM(HSOP28)
0.1
R502 0
C140.1F
R16
61k
R167 100
2626
CX-JDS30
CX-JDS30
1 2
A
B
C
D
E
F
G
H
I
3 4 5 6 7 8 9 10 11 12 13 14
6
8
1
1
E
E
E
EEE
E
E
3
7
7
4
RU
RU
S
SE
E
E E
1
1
7
5
E
E
E
131
1
3
1
3
E
E
E
E
E
R419
R418
12
29 30
R
SPEAKER
(CHASSIS) (CHASSIS)
FAN
TUNER
L
3 1
(page 34)CN301BOARD
DS-AMPLIFIER(403)
C
(page 36)WH002BOARD
DS-POWER
G
(page 36)WH001BOARD
DS-POWER
H
(page 32)FFC552(11P)
BOARDDS-PAI/HP/MIC
B
(page 29)CN601BOARD
DS-PANEL
A
1
LCH
RCHREC/PB
HEAD(REC/PB/ERASE)
ERASE
-
+-
+
-
+
7
IC401
IC101
IC102
FFC802
111
6-4. PRINTED WIRING BOARD – MAIN SECTION – • See page 21 for Circuit Boards Location. :Uses unleaded solder.
R141 1-216-845-11 METAL CHIP 100K 5% 1/10WR142 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR143 1-216-864-11 SHORT CHIP 0R144 1-216-864-11 SHORT CHIP 0R145 1-216-864-11 SHORT CHIP 0
R185 1-259-296-11 CARBON 470 5% 1/2WR191 1-216-821-11 METAL CHIP 1K 5% 1/10WR192 1-216-821-11 METAL CHIP 1K 5% 1/10WR195 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR196 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R405 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R406 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR407 1-216-833-11 METAL CHIP 10K 5% 1/10WR408 1-216-833-11 METAL CHIP 10K 5% 1/10WR409 1-216-833-11 METAL CHIP 10K 5% 1/10W
R410 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR411 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR412 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR413 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR414 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R415 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR416 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR417 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR418 1-216-853-11 METAL CHIP 470K 5% 1/10WR419 1-216-853-11 METAL CHIP 470K 5% 1/10W
R420 1-216-849-11 METAL CHIP 220K 5% 1/10WR421 1-216-845-11 METAL CHIP 100K 5% 1/10WR423 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR424 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR427 1-216-837-11 METAL CHIP 22K 5% 1/10W
R428 1-216-837-11 METAL CHIP 22K 5% 1/10WR429 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
(MX, E51)R429 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RU)R430 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
(MX, E51)R430 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RU)
R433 1-216-841-11 METAL CHIP 47K 5% 1/10WR434 1-216-841-11 METAL CHIP 47K 5% 1/10WR435 1-216-837-11 METAL CHIP 22K 5% 1/10W
(RU)R436 1-216-837-11 METAL CHIP 22K 5% 1/10W
(RU)R437 1-216-821-11 METAL CHIP 1K 5% 1/10W
(MX, E51)
R437 1-216-864-11 SHORT CHIP 0 (RU)R438 1-216-821-11 METAL CHIP 1K 5% 1/10W
(MX, E51)R438 1-216-864-11 SHORT CHIP 0 (RU)R439 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR440 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R441 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR442 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR443 1-216-833-11 METAL CHIP 10K 5% 1/10WR444 1-216-833-11 METAL CHIP 10K 5% 1/10WR445 1-216-864-11 SHORT CHIP 0
R446 1-216-864-11 SHORT CHIP 0R447 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR448 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR449 1-216-864-11 SHORT CHIP 0R450 1-216-864-11 SHORT CHIP 0
R471 1-216-864-11 SHORT CHIP 0R479 1-216-809-11 METAL CHIP 100 5% 1/10WR480 1-216-809-11 METAL CHIP 100 5% 1/10WR481 1-164-315-11 CERAMIC CHIP 470PF 5% 50VR482 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
R501 1-216-841-11 METAL CHIP 47K 5% 1/10WR502 1-216-849-11 METAL CHIP 220K 5% 1/10W
DS-MAIN
57
CX-JDS30
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R503 1-216-849-11 METAL CHIP 220K 5% 1/10WR504 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR505 1-216-833-11 METAL CHIP 10K 5% 1/10W
R506 1-216-853-11 METAL CHIP 470K 5% 1/10WR507 1-216-861-11 METAL CHIP 2.2M 5% 1/10WR508 1-216-801-11 METAL CHIP 22 5% 1/10WR509 1-216-805-11 METAL CHIP 47 5% 1/10WR510 1-216-841-11 METAL CHIP 47K 5% 1/10W
R511 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR512 1-216-833-11 METAL CHIP 10K 5% 1/10WR513 1-216-853-11 METAL CHIP 470K 5% 1/10WR514 1-216-861-11 METAL CHIP 2.2M 5% 1/10WR515 1-216-801-11 METAL CHIP 22 5% 1/10W
R516 1-216-805-11 METAL CHIP 47 5% 1/10WR517 1-216-841-11 METAL CHIP 47K 5% 1/10WR518 1-216-809-11 METAL CHIP 100 5% 1/10WR519 1-216-841-11 METAL CHIP 47K 5% 1/10WR520 1-216-809-11 METAL CHIP 100 5% 1/10W
R521 1-216-841-11 METAL CHIP 47K 5% 1/10WR522 1-216-801-11 METAL CHIP 22 5% 1/10WR523 1-216-837-11 METAL CHIP 22K 5% 1/10WR524 1-216-821-11 METAL CHIP 1K 5% 1/10WR525 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R526 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR527 1-216-837-11 METAL CHIP 22K 5% 1/10WR528 1-216-821-11 METAL CHIP 1K 5% 1/10WR529 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR530 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R531 1-216-833-11 METAL CHIP 10K 5% 1/10WR532 1-216-833-11 METAL CHIP 10K 5% 1/10WR533 1-216-833-11 METAL CHIP 10K 5% 1/10WR534 1-216-833-11 METAL CHIP 10K 5% 1/10WR535 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R536 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR537 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR538 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR539 1-216-849-11 METAL CHIP 220K 5% 1/10WR540 1-216-833-11 METAL CHIP 10K 5% 1/10W
R542 1-216-793-11 METAL CHIP 4.7 5% 1/10WR544 1-216-833-11 METAL CHIP 10K 5% 1/10WR545 1-216-833-11 METAL CHIP 10K 5% 1/10WR546 1-216-793-11 METAL CHIP 4.7 5% 1/10WR547 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R548 1-216-793-11 METAL CHIP 4.7 5% 1/10WR573 1-216-821-11 METAL CHIP 1K 5% 1/10WR574 1-216-821-11 METAL CHIP 1K 5% 1/10WR581 1-216-845-11 METAL CHIP 100K 5% 1/10WR582 1-216-833-11 METAL CHIP 10K 5% 1/10W
R583 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR801 1-216-833-11 METAL CHIP 10K 5% 1/10WR803 1-216-864-11 SHORT CHIP 0R804 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR805 1-216-833-11 METAL CHIP 10K 5% 1/10W
R806 1-216-821-11 METAL CHIP 1K 5% 1/10WR807 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR808 1-216-833-11 METAL CHIP 10K 5% 1/10WR809 1-216-833-11 METAL CHIP 10K 5% 1/10WR810 1-216-864-11 SHORT CHIP 0
R811 1-216-864-11 SHORT CHIP 0R812 1-216-864-11 SHORT CHIP 0R813 1-216-864-11 SHORT CHIP 0R814 1-216-864-11 SHORT CHIP 0R871 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R872 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR873 1-259-264-91 CARBON 22 5% 1/2WR874 1-259-264-91 CARBON 22 5% 1/2WR875 1-216-864-11 SHORT CHIP 0R876 1-216-821-11 METAL CHIP 1K 5% 1/10W
R877 1-216-837-11 METAL CHIP 22K 5% 1/10WR878 1-216-837-11 METAL CHIP 22K 5% 1/10WR879 1-216-817-11 METAL CHIP 470 5% 1/10WR880 1-216-821-11 METAL CHIP 1K 5% 1/10WR881 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R882 1-216-789-11 METAL CHIP 2.2 5% 1/10WR883 1-216-849-11 METAL CHIP 220K 5% 1/10WR884 1-216-801-11 METAL CHIP 22 5% 1/10WR885 1-216-789-11 METAL CHIP 2.2 5% 1/10W
IC601 8-759-643-83 IC uPD16315GB-3BSIC602 6-600-446-01 IC RPM7240-H18 ( )IC603 8-759-713-61 IC PST3429ULIC604 6-805-527-01 IC M30302MCP-A04FPU0IC605 6-704-135-01 IC MM1614A
< SHORT >
JR601 1-216-864-11 SHORT CHIP 0
< COIL >
L602 1-469-152-11 FERRITE, EMI (SMD) (2012)L603 1-216-864-11 SHORT CHIP 0L604 1-216-864-11 SHORT CHIP 0L605 1-216-864-11 SHORT CHIP 0L606 1-216-864-11 SHORT CHIP 0
L607 1-216-864-11 SHORT CHIP 0L608 1-216-864-11 SHORT CHIP 0L609 1-216-864-11 SHORT CHIP 0L610 1-216-864-11 SHORT CHIP 0L611 1-469-152-11 FERRITE, EMI (SMD) (2012)
< LED >
LED607 8-719-063-93 DIODE SLR325VC-N-T32 (STAND BY)LED608 6-500-641-01 DIODE SLI-325URC (i-Bass)
0106 1-827-226-31 CORD, POWER (MX)0106 1-830-384-11 CORD, POWER (E51, RU)0157 8-820-244-01 OPTICAL PICK-UP (KSM-215DCP/C2NP)
158 1-827-992-11 WIRE (FLAT TYPE) (16 CORE)
161 1-775-251-11 WIRE (FLAT TYPE) (27 CORE)
162 1-773-021-11 WIRE (FLAT TYPE) (15 CORE)201 1-797-193-11 MECH, CD
0PT001 1-443-701-11 TRANSFORMER, POWER (RU)0PT001 1-443-722-11 TRANSFORMER, POWER (MX)0PT002 1-443-700-11 TRANSFORMER, POWER (E51)
DS-POWER DS-VOL
63
MEMO
CX-JDS30
CX-JDS30
REVISION HISTORY
Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised page allows you to jump to the next revisedpage.