Airport Hangars And Aircraft Maintenance Operations Minor Project Report Submitted in partial fulfillment of the requirements for the award of the degree of Bachelor of Technology In Aerospace Engineering AMITY UNIVERSITY DUBAI (2012-2016) Submitted to: Submitted by: Mr. Sarath Raj Michael Bseliss Lecturer Faculty A40105513001 Amity University Dubai Semester 6 / 3 rd. Year
33
Embed
Airport Hangars And Aircraft Maintenance Operations
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Airport Hangars And
Aircraft Maintenance Operations
Minor Project Report
Submitted in partial fulfillment of the requirements for the award
of the degree of
Bachelor of Technology
In Aerospace Engineering
AMITY UNIVERSITY DUBAI
(2012-2016)
Submitted to: Submitted by:
Mr. Sarath Raj Michael Bseliss Lecturer Faculty A40105513001 Amity University Dubai Semester 6 / 3rd. Year
1
BONAFIDE CERTIFICATE
This is to certify that Michael Bseliss, a student of B.Tech in Aerospace Engineering
Department has carried out the work presented in this report entitled “Airport
Hangars and Aircraft Maintenance Operations” as a part of 2015 year
programme of Bachelor of Technology in Aerospace Engineering from Amity
University, Dubai - UAE under my supervision.
Name of Faculty Guide: Signature of Faculty Guide:
2
ACKNOWLEDGEMENT
I thank my faculty guide Mr. Sarath Raj for his full support, help and guidance.
I acknowledge his advice and suggestions that have helped me to make this report a
productive one.
I express our gratitude towards my parents for their complete motivation, support
and help in completing this term paper successfully.
I proudly dedicate my success in preparing this project to my country Syria, and my
lovely city Aleppo and hope that it will be fine soon
Lastly, I acknowledge every faculty and all my friends at Amity University, who have
been gracious in providing me with the required suggestion and help in every
possible way.
3
Certificate 1
Acknowledgement 2
Introduction 5
Airport Hangars History 8
Hangars Types 10
3.1 Cargolifter Hangar 11
3.2 Tee Hangars 12
3.3 Bellman Hangar 13
3.4 Bessonneau Hangar 14
3.5 Blister Hangar 15
3.6 Underground Hangars 16
Aircraft Maintenance Operations 17
4.1 Inspection Types 18
4.2 Aircraft Maintenance Checks 19
4.3 MRO Operations 22
4
-All New- Hangars 23
Amity International Airport Hangars 28
Conclusion 30
References 32
5
An airport is an aerodrome with facilities for commercial aviation flights to take off and
land. Airports usually have facilities to maintain and store planes, and a air traffic control
tower. [1] An airport consists of adjacent utility buildings like control towers, terminals
and hangars as well as a landing area, that comprises an aerially accessible open space
including at least one operationally active surface such as a runway for an aircraft to take
off or a helipad. [2] Fixed base operator services, air traffic control centers, airport
aprons, passenger facilities such as lounges and restaurants, and emergency services may
exist in larger airports.
The Federal Aviation Administration or the FAA is an agency of the United States'
government which controls Aviation. This agency mandates identification standards for
airport layout which is meant to help pilots in recognizing runways from the air easily
6
and to safely taxi from the runway to the gate. [3] From painted stripes & runway
numbers to runway lights and signs & airport.
Airports and aircrafts have evolved and continue to evolve. Airplanes began in the 1950-s
to have a variety of uses for transportation & business. Instead off tail skids, aircrafts
were equipped with steerable tail wheels to operate more easily on the ground.
As airplanes became larger and heavier heavier and larger it was important for airports to
have hard surface runways [3] instead of grass or gravel fields because such fields
couldn’t support the weight of heavy airplanes. (Boeing 747 at takeoff can weigh more
than 800,000 pounds). Eventually airports started to offer more services for airplane
operators & their increasing number of passengers.
A modern large airport today has thousands of workers, accommodates tens of thousands
of passengers, and loads or unloads hundreds of thousands of pounds of baggage and
cargo daily.
There are many types of airports that exist today as part of the United States' air
transportation system. [2] These airports range from a single grass airstrip in a rural area
or an agricultural to the large airports which serve major cities.
There are seven basic types of airports:
Rural airstrip.
Private airport.
Military airports.
Major city airport.
Small community airport.
Regional airport.
Regional community airport.
The differences one from the other depends upon the types of services it provides, [1] the
length of the runways with its complementary terminal facilities, the size aircraft it
serves, and its proximity to a densely populated area.
7
Airports usually consist of many buildings and units, the main parts of airport are:
1) Passenger terminal buildings.
2) Control towers.
3) Airport Hangars and aircraft maintenance buildings.
4) Fire & Safety stations.
5) Fuel Tanks.
The airport model made by Aerospace Engineering students contains the above
mentioned parts, where this report will discuss the Airport Hangars part as well as the
maintenance operations which is done in the airport.
8
A hangar is a closed building structure to hold airplanes in protective storage. Usually
hangars are built of metal, [4] but other materials such as concrete & wood may also be
used.
Hangars are used for: Protection from direct sunlight, protection from the weather,
manufacture, maintenance, repair, assembly & storage of aircraft on airfields, aircraft
carriers & ships.
During the early 20th century, Carl Richard Nyberg used a hangar to store his Flugan
(fly). [4] Louis Bleriot in 1909 crash-landed on a northern French farm in Les Baraques
(b/n Calais & Calais) then rolled his monoplane into the farmer's cattle pen. [4]
Meanwhile, Bleriot was in a race to be the first man to cross the English Channel in a
heavier-than-air aircraft, so he set up his headquarters in the unused shed.
The Wright brothers stored & repaired their airplane in a hangar [4] made by wood
constructed in 1902 at Kill Devil Hills in North Carolina for their glider.
The earliest airplane hangars were known as airplane sheds in Britain.
9
Before World War 1 when aviation became established in Britain, standard designs of
hangar gradually appeared with military types [4] also such as the side-opening airplane
shed of 1913 and the Bessonneau hangar - both of which were later adopted by the Royal
Flying Corps.
The largest hangars ever built were those for airships, such as Hangar One (Mountain
View, California) measuring 1,133x308x198 feet, [4] as well as Goodyear Airdock
measuring 1,175x325x211 feet.
10
Special structures are necessary to build a hangar. The width of doors should be large, the
aircraft entrance included. [5] Large airplanes need complex structure. Sizes can be
classified as follows according to the span of the hangar:
Size Span (meters)
S Less than 30 m
M 30–60 m
L 60–90 m
XL 90–120 m
XXL More than 120 m
For the largest aircraft in the world XXL hangars are built, for example:[5] the Airbus
A380, Antonov 225 and Boeing 747. Such structures are the most complex to erect.
Airship hangars (also known as "airship sheds") are generally bigger than normal aircraft
hangars, especially in terms of height. Early airships used hydrogen gas to provide them
with enough buoyancy for
flight, hence their hangars had
to provide protection from stray
sparks to prevent the flammable
gas from exploding. Hangars
that held [5] multiple vehicles
of this type were at risk from
chain-reaction explosions. So
most hangars for hydrogen-
based airships were built to house only one or two such craft.
11
1) Cargolifter Hangar:
It is a hangar for production and operation of the CL160 & engineering team facilities
were built at Brand-Briesen Airfield on the former Soviet Air Force base, [5] acquired to
enable development and operations.
This hangar (360 m long, 220 m wide and 106 m high), is a freestanding steel-dome
"barrel-bowl" structure big enough to fit the Eiffel Tower on its side. It was equipped also
with a cutting table {180 m} to manufacture the envelope of airship.
12
2) Tee Hangars:
It is a type of enclosed structure designed to hold aircraft in protective storage. Primarily
used for private aircraft at general aviation airports. [5] It is usually constructed of metal;
since this type of hangars is more economical than normal rectangular hangars, they are
used for private airplane at general aviation airports. There are two types of Tee hangars:
standard (sometimes called stacked) & nested.
Standard Tee Hangars:
Provide additional storage area & can use
rolling doors. [5] In this figure, the odd-
shaped areas at the end of the hangar clusters
may be omitted, or may be included as part
of the end hangars, or may be used as
segregated storage, shop or office space.
Nested Tee Hangars:
Require less building material than standard
and are wider, but shorter, thereby reducing
the length of taxiway required to abut the building. [5] The disadvantage is that rolling
doors cannot be used.
13
3) Bellman Hangar:
It is temporary hangar was designed in 1936 in the United Kingdom by N. S. Bellman
Directorate of Works structural engineer, [6] as a temporary hangar capable of being built
or dismantled by unskilled labor with simple equipment and to be transportable easily. [6]
By November 1938, 10 had even been supplied to Russia.
Its general dimensions were 175 ft long, 95 ft wide (87 ft 9in clear width) and 25 ft (clear
height). It was constructed in 14 bays at 12 ft 6in centres based on a unit system of rolled
steel sections; both walls and roof used the same standard units joined at the junction of
wall and roof by a standard corner unit.
The time taken for 12 men to erect the hangar at Thornaby, including levelling the
ground, laying door tracks, erecting the steelwork, [6] and fitting oiled canvas doors was
500 man-hours.
Two light jib derricks
using timber poles
were required to erect
the fabricated [6]
vertical and side
members. The roof
trusses were assembled on the ground before being lifted into position.
14
4) Bessonneau Hangar:
The Bessonneau [7] hangar was a portable timber and canvas aircraft hangar used by the
British Royal Flying Corps during World War I.
In about 1908, [7] the Bessonneau hangar was designed and manufactured by the French
rope and canvas manufacturer Etablissements Bessonneau, in 1910 specifically employed
to protect aircraft participating in a race from Angers to Saumur in France.
The hangar was supplied as a kit of parts that could be easily erected, dismantled,
transported and re-erected at another location. The principal material of the framework
was wood, joined by wooden plates, steel brackets and steel bolts. [7] Vertical stanchions
supported roof trusses, with extensively triangulated ties and beams. Bays (units) of
stanchions and trusses were built up and connected to each other, with each hangar
assembled with 6, 9 or 12 bays to achieve different hangar lengths. [7] Wooden flying
buttresses were applied to the sides and rear, to ensure rigidity, and ropes were used to tie
down the whole structure onto steel pickets driven into the ground. Snow poles were
attached to the underside of selected trusses, and hinged to allow them to be lowered for
extra roof support in the event of heavy snow or high winds. [7] The tailored canvas
covering was tied to the framework with ropes.
15
The most common variant in Britain was the 6-bay design, providing inside clear
dimensions of width (span) 20 metres (65 ft 6 in), length 24 metres (79 ft) and height 4
metres (13 ft 2 in). [7] Outside dimensions were width 22 metres (72 ft), length 28 metres
(91 ft 10 in), height 7.7 metres (25 ft 5 in), excluding picketing ropes.
5) Blister Hangar:
A blister hangar is a novel arched, portable aircraft hangar designed by notable British
airport architect Graham R Dawbarn patented by Miskins and Sons in 1939. Originally
made of wooden ribs clad with profiled steel sheets, [5] steel lattice ribs and corrugated
steel sheet cladding later became the norm. It does not require a foundation slab and can
be anchored to the ground with iron stakes. Numerous examples were manufactured for
military use in World War 2 and various different sizes were available. Many found post-
war use as agricultural or industrial buildings and some still remain in use on airfields
such as Fairoaks, Redhill and White Waltham today.
16
6) Underground Hangars:
An underground hangar is a type of hangar for military aircraft, usually dug into the side
of a mountain for protection. [8] It is bigger and more protected than a hardened aircraft
shelter (HAS).
An underground hangar complex may include tunnels containing the normal elements of
a military airbase - fuel storage, [8] weapon storage, rooms for maintaining the aircraft
systems, a communications centre, briefing rooms, kitchen, dining rooms, sleeping areas
and generators for electrical power.
Countries that have used underground hangars include Albania, China, India, Pakistan,
Italy, North Korea, Norway, South Africa, Sweden, Switzerland, Taiwan, Vietnam and
Yugoslavia.
The Indian Air Force operates underground hangars. Sukhoi Su-30 MKI have been
stationed at Trishul Air-base situated in Bareilly, [8] Uttar Pradesh, India. It houses one
of the largest underground hangars in Asia. Adampur, situated in Punjab, houses an air-
base with underground hangars. It is the home base for MiG-29.
17
Overhaul, is a common term or concept used in aviation industry, refers to the operations
of airplanes’ examination to make the required changes.
Aircraft maintenance is defined as the inspection, [9] overhaul and repair or modification
of airplane and/or its component.
Maintenance includes the removal or installation of a component from an aircraft or