AIRJET Jet Fans Axial-Flow Fans Axial-Roof Fans Smoke Exhaust Axial-Flow Fans Smoke Exhaust Axial Roof Fans H UNGARO-VENTILÁTOR LTD.
AIRJET Jet Fans Axial-Flow Fans Axial-Roof Fans Smoke Exhaust Axial-Flow Fans Smoke Exhaust Axial Roof Fans
H UNGARO-VENTILÁTOR LTD.
2 HV-VMA middle pressure axial-flow fan series
Middle pressure axial-flow fan with aluminum impeller
and direct drive.
VMA nominal sizes: 560-1000mm.
For extraction or supply of pure air with max.
temperature of 50°C or 80°C. Also for horizontal and
vertical mounting positions!
Description:
Casing of sheet-steel with rolled flanges on both sides and
with bolted motor support. Surfaces protected through hot
dip galvanizing or powder-painting.
Impeller with airfoil aluminum cast alloy blades and aluminum cast alloy hub and with a taperlock hub connection on
motor shaft. Pitch angle is infinitely adjustable at rest. Impeller is dynamically balanced according to EN ISO 1940-1,
balance quality class G6.3.
Three-phase alternating current motor /IEC – standard motor in B3 mounting form, protection type IP 55/ insulation
class ISO-H. Motor power selected for a cold start at pure air with a density of ρ =1,2kg/m3. Electrical wiring on the
externally located terminal box.
Performance curves are according to EN24163 and EN ISO 5801 tested in a tube testing station.
HUNGARO-VENTILÁTOR LTD.
Táncsics Mihály utca 18. H-9483 Sopronkövesd Hungary
Telephone: +36-99/536-072 Fax: +36-99/536-073
Mobil:+36-30/689-5939, +36-30/396-5162 E-mail: info@hungaro-yentilator hu
HV-VMB middle pressure axial-flow fan series 3
Middle pressure axial-flow fan with aluminum
impeller and direct drive.
VMA nominal sizes: 560-1000mm.
For extraction or supply of pure air with max.
temperature of 50°C or 80°C. Also for horizontal
and vertical mounting positions!
Description:
Casing of sheet-steel with rolled flanges on both
sides and with bolted motor support. Surfaces protected through hot dip galvanizing or powder-painting.
Impeller with airfoil aluminum cast alloy blades and aluminum cast alloy hub and with a taperlock hub connection on
motor shaft. Pitch angle is infinitely adjustable at rest. Impeller is dynamically balanced according to EN ISO 1940-1,
balance quality class G6.3.
Three-phase alternating current motor /IEC – standard motor in B3 mounting form, protection type IP 55/ insulation
class ISO-H. Motor power selected for a cold start at pure air with a density of ρ =1,2kg/m3. Electrical wiring on the
externally located terminal box.
Performance curves are according to EN24163 and EN ISO 5801 tested in a tube testing station.
HUNGARO-VENTILÁTOR LTD.
Táncsics Mihály utca 18. H-9483 Sopronkövesd Hungary
Telephone: +36-99/536-072 Fax: +36-99/536-073
Mobil:+36-30/689-5939, +36-30/396-5162 E-mail: info@hungaro-yentilator hu
4 HV-VMC middle pressure axial-flow fan series
Middle pressure axial-flow fan with plastic blade
impeller and direct drive.
VMC nominal sizes: 315-1250 mm
For extraction or supply of pure air with max.
temperature of 50°C o r80°C. Also for horizontal
and vertical mounting positions.
Description:
Casing of sheet-steel with rolled flanges on both
sides and with bolted motor support. Surfaces
protected through hot dip galvanizing or powder painting.
Impeller with airfoil plastic (PP or PAG) blades and aluminum cast alloy hub and with an easy-to-assembly hub-shaft
connection. Pitch angle is in steps adjustable at rest. Impeller is dynamically balanced according to EN ISO 1940-1,
balance quality class G 6.3.
Three-phase alternating current motor / IEC - standard motor in B3 mounting, protection type IP 55 / insulation
class F or H. Motor power selected for a cold-start at pure air with a density of ρ=1,2kg/m3. Electrical wiring on
the externally located terminal box.
Performance curves are according to EN 24163 and EN ISO 5801 tested in a tube testing station.
HUNGARO-VENTILÁTOR LTD.
Táncsics Mihály utca 18. H-9483 Sopronkövesd Hungary
Telephone: +36-99/536-072 Fax: +36-99/536-073
Mobil:+36-30/689-5939, +36-30/396-5162 E-mail: info@hungaro-yentilator hu
HV-ZVMC middle pressure twin axial-flow fan series 5
Middle pressure twin axial-flow fan with plastic
blade impeller and direct drive.
ZVMC nominal sizes: 315-1250mm
For extraction or supply of pure air with max.
temperature of 50°C or 80 °C. Also for horizontal
and vertical mounting positions!
Description:
Casing of sheet-steel with rolled flanges on both
sides and with bolted motor support. Surfaces protected through hot dip galvanizing or powder-painting.
Impeller with airfoil plastic (PPor PAG) blades and aluminum cast alloy hub and with an easy-to-assembly hub-shaft
connection. Pitch angle is in steps adjustable at rest. Impeller is dynamically balanced according to EN ISO 1940-1, balance
quality class G6.3.
Three-phase alternating current motor / IEC - standard motor in B3 mounting, protection type IP 55 / insulation class F
or H. Motor power selected for a cold start at pure air with a density of ρ = 1,2kg/m3. Electrical wiring on the externally
located terminal box.
Performance curves are according to EN 24163and EN ISO 5801 tested in a tube testing station.
HUNGARO-VENTILÁTOR LTD.
Táncsics Mihály utca 18. H-9483 Sopronkövesd Hungary
Telephone: +36-99/536-072 Fax: +36-99/536-073
Mobil:+36-30/689-5939, +36-30/396-5162 E-mail: info@hungaro-yentilator hu
6 HV-VM..D middle pressure axial-flow roof fan
Middle pressure axial-flow roof-fan with aluminum/plastic blade impeller and direct drive. Also for supply and exhaust. VMAD Roof-fan with an axial-flow fan type VMA - aluminum impeller VMBD Roof-fan with an axial-flow fan type VMB - aluminum impeller VMCD Roof-fan with an axial-flow fan type VMC - plastic blades
For extraction or supply of pure air with max. temperature of 50°C or
80°C. For roof installation in vertical mounting position!
Description:
A roof hood mounted on an axial-flow fan. In case of exhaust, a use of an inlet
cone - as
optional accessory - is necessary.
Three-phase alternating current motor I IEC - standard motor in. B3
mounting, protection type IP 55 insulation class F or H. Motor power selected for a cold start at pure air with a density of ρ =
1.2 kg/m3. Electrical wiring on the externally located terminal box.
Performance curves are according to EN 24163 and EN ISO 5801 tested in a tube testing
station.
HUNGARO-VENTILÁTOR LTD.
Táncsics Mihály utca 18. H-9483 Sopronkövesd Hungary
Telephone: +36-99/536-072 Fax: +36-99/536-073
Mobil:+36-30/689-5939, +36-30/396-5162 E-mail: info@hungaro-yentilator hu
HV-VM..DT middle pressure axial-flow roof fan 7
Middle pressure axial-flow roof fan with aluminum/plastic blade impeller and direct drive. Also for supply and exhaust.
A1so for supply and exhaust.
VMADT Roof fan with an axial-flow fan type VMA - aluminum impeller
VMBDT Roof fan with an axial-flow fan type VMB - aluminum impeller
VMCDT Roof fan with an axial-flow fan type VMC - plastic blades
For extraction or supply of pure air with max. temperature of 5O°C or 80°C.
For roof installation in vertical mounting position!
Description:
A roof hood mounted on an axial-flow fan. In case of exhaust, a use of an inlet cone - as
optional accessory - is necessary.
Three-phase alternating current motor I IEC - standard motor in. B3 mounting, protection type IP 55 insulation class F or
H. Motor power selected for a cold start at pure air with a density of ρ = 1.2 kg/m3. Electrical wiring on the externally located
terminal box.
Performance curves are according to EN 24163 and EN ISO 5801 tested in a tube testing
station.
HUNGARO-VENTILÁTOR LTD.
Táncsics Mihály utca 18. H-9483 Sopronkövesd Hungary
Telephone: +36-99/536-072 Fax: +36-99/536-073
Mobil:+36-30/689-5939, +36-30/396-5162 E-mail: info@hungaro-ventilator hu
8 HV-BVHA F400/F300 smoke exhaust axial-flow fan series
High pressure smoke exhaust axial flow fan F400 (400°C/120min.) / F300 (300°C/120min.)
BVHA nominal sizes: 335-1400mm
Tested and certified according to EN 12101-3, class F400 and F300. Also for horizontal and vertical installation.
Description: Casing of sheet-steel with rolled flanges on both sides and with welded outlet guide vanes as motor support. Surfaces protected through hot dip galvanizing or powder painting.
Impeller with steel blades welded on a steel hub that directly mounted on motor shaft. Pitch angle is fixed. Impeller is dynamically
balanced according to EN ISO 1940-1, balance quality class G 6.3.
Three-phase alternating current motor / special F400/F300 motor in B3 or B14 mounting, protection type IP55 / insulation class H.
Motor power selected for a cold start at pure air with a density of ρ =1,2kg/m3. Electrical wiring on the externally located terminal
box.
Performance curves are according to EN 24163 and EN ISO 5801 tested in a tube testing station.
Special fans: •Tunnel fans on both sides silencers, tested and certified according to EN 12101-3, class F400 or F300.
HUNGARO-VENTILÁTOR LTD.
Táncsics Mihály utca 18. H-9483 Sopronkövesd Hungary
Telephone: +36-99/536-072 Fax: +36-99/536-073
Mobil:+36-30/689-5939, +36-30/396-5162 E-mail: info@hungaro-ventilator hu
HV-AIRJET AJU/AJR F300 jet-fan series 9
Jet-fan F300 (300°C/120min.) or normal.
AIRJET nominal sizes : 280…400mm Tested and certified according to EN 12101-3, class
F300.
Description:
In unidirectional (AJU) or reversible (AJR) execution.
Insists of an in the middle situated axial-flow fan and both
sides silencers in a high-sparing oval design. The interior
set of fan-motor may be easily pulled out through the
silencer. Direction of the outlet air may be regulated by
using the outlet-louvres.
Impeller with airfoil aluminum cast alloy
blades and aluminum cast alloy hub and
with a taperlock hub connection on motor
shaft. Pitch angle is infinitely adjustable at
rest. Impeller is dynamically balanced
according to EN ISO 1940-1, balance
quality class G6.3.
Three-phase alternating current , special
F300 or normal motor in B3 mounting
form, protection type IP 55 / insulation
class H or F. Motor power selected for a
cold start at pure air with a density of ρ=
1,2kg/m3.
Optional electrical wiring on the externally located terminal box.
AJRJ/AJU jet-fans are tested and certified according to EN 12101-3:2002/ EN 12101-3:2002/AC:200S in classes of
F200(120) and F300(120) temperature (time).
Performance curves are according to EN 24163 and EN ISO 5801 tested in a tube testing station.
HUNGARO-VENTILÁTOR LTD.
Táncsics Mihály utca 18. H-9483 Sopronkövesd Hungary
Telephone: +36-99/536-072 Fax: +36-99/536-073
Mobil:+36-30/689-5939, +36-30/396-5162 E-mail: info@hungaro-ventilator hu
•
10 BVHA F400/F300 + louvre-hood as smoke exhaust roof-fan
High pressure smoke exhaust axial roof-fan F400 (400°C/120min.) / F300 (300°C/120min.)
BVHA F300/F400 + louvre hood nominal sizes: 335-1400mm
Tested and certified according to EN 12101-3, class F400 (400°C/120min.) and F300 (300°C/120min.)
Description:
A pressure activated louvre-hood mounted on a BVHA smoke exhaust
axial-flow fan in vertical mounting position as roof fan for external usage.
Smoke outlet direction is above 45°.
Casing of sheet-steel with rolled flanges on both sides and with welded outlet
guide vanes as motor support. Surfaces protected through hot dip galvanizing
or powder-painting.
Impeller with steel blades welded on steel hub, that directly mounted on
motor shaft. Pitch angle is fixed. Impeller is dynamically balanced according
to EN ISO 1940-1, balance quality c1ass G6.3.
Three-phase alternating current, special F400/F300 motor in mounting form
B3 or B14. Protection type IP55 / insulation class H. Motor power selected
for a cold start at pure air with a density of ρ = 1,2 kg/m3. Electrical wiring
on the externally located terminal box.
Performance curves are according to EN 24163 and EN ISO 5801, tested in a
tube testing station.
HUNGARO-VENTILÁTOR LTD.
Táncsics Mihály utca 18. H-9483 Sopronkövesd Hungary
Telephone: +36-99/536-072 Fax: +36-99/536-073
Mobil:+36-30/689-5939, +36-30/396-5162 E-mail: info@hungaro-ventilator hu