SAMSUNG | 95 1 TROUBLESHOOTING 8 Set up the model Option 8-5. Set up the Model Option Step 1 : Preparing the remocon to main PBA option set 1 st Remove the battery from the remocon. 2 nd Press the temperature raise/down button simultaneously and insert the battery again. 3 rd Make sure the remocon display shown as . Step 2 : Second stage preparation of the remocon option set. ex) Option No. : 066025-172362 ❈ Note ; In case the wrong letter has been selected, continue to press the button until the correct letter appears. 1 st If the first stage number “ ” appears on the display, proceed to the second stage. 2 nd Every time the ! and & button, “ ” and “ ” each continue to appear. 3 rd Whenever pressing the @, #, $, %, ^, *, (, ), 1, 2 button, the number increases from 0~9(0123456789) and A, b, C, d, E, F each time. ! If the first number is , it is correct otherwise press until appear. @ When pressing the button ~ appear on the display, select one of them. # When pressing the button ~ appear on the display, select one of them. $ When pressing the button ~ appear on the display, select one of them. % When pressing the button ~ appear on the display, select one of them. ^ When pressing the button ~ appear on the display, select one of them.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
SAMSUNG | 95
1TROUBLESHOOTING 8Set up the model Option
8-5. Set up the Model Option
Step 1 : Preparing the remocon to main PBA option set
1st Remove the battery from the remocon.
2nd Press the temperature raise/down button simultaneously and insert the battery again.
3rd Make sure the remocon display shown as .
Step 2 : Second stage preparation of the remocon option set.
ex) Option No. : 066025-172362
❈ Note ; In case the wrong letter has been selected, continue to press the button until the correct letter appears.
1st If the first stage number “ ” appears on the display, proceed to the second stage.
2nd Every time the ! and & button, “ ” and “ ” each continue to appear.
3rd Whenever pressing the @, #, $, %, ^, *, (, ), 1, 2 button, the number increases from
0~9(0123456789) and A, b, C, d, E, F each time.
! If the first number is , it is correct otherwise press until appear.
@ When pressing the button ~ appear on the display, select one of them.
# When pressing the button ~ appear on the display, select one of them.
$ When pressing the button ~ appear on the display, select one of them.
% When pressing the button ~ appear on the display, select one of them.
^ When pressing the button ~ appear on the display, select one of them.
DB98_08187A(1)_57~100 3/27/03 2:24 PM Page 95
Andrey Chebotarev
Standart
96 | SAMSUNG
8 TROUBLESHOOTING
Set up the Model Option (Cont.)
Step 3 : Reconfirming option set after completion
(in case of ex. 066025-172362)
After pressing selector for the mode, the display shown as .
After pressing selector for the mode, the display shown as .
Step 4 : Pressing the ON/OFF button ( )When pressing the operation ON/OFF key with the direction of remote controller for unit, the sound “Ding” or “Diriring” is
heard and the OPERATION LED lamp is flickering at the same time, then the input of option is completed.
(If the diriring sound isn’t heard, try again pressing the ON/OFF button.)
Step 5 : Unit operation test-runFirst, Remove the battery from the remote controller.
Second, Re-insert the battery into the remote controller.
Third, Press ON/OFF key with the direction of remote controller for set.
! If the first number is , it is correct otherwise press until appear.
@ When pressing the button ~ appear on the display, selectone of them.
# When pressing the button ~ appear on the display, selectone of them.
$ When pressing the button ~ appear on the display, selectone of them.
% When pressing the button ~ appear on the display, selectone of them.
^ When pressing the button ~ appear on the display, selectone of them.
Error Mode :
1st If all lamps of indoor unit are flickering, Plug out and plug in again and pressing ON/OFF key to retry.
2nd If the unit is not working properly or all lamps are continuously flickering after setting the option code, seeif the correct option code is set up for it’s model.
DB98_08187A(1)_57~100 3/27/03 2:24 PM Page 96
Andrey Chebotarev
Standart
97 | SAMSUNG
8Set up the model Option
8-5. Set up the Model Option
Step 1 : Preparing the remocon to main PBA option set
1st Remove the battery from the remocon.
2nd Press the temperature raise/down button simultaneously and insert the battery again.
3rd Make sure the remocon display shown as .
Step 2 : Second stage preparation of the remocon option set.
❈ Note ; In case the wrong letter has been selected, continue to press the button until the correct letter appears.
1st If the first stage number “ ” appears on the display, proceed to the second stage.
2nd Every time the ! and & button, “ ” and “ ” each continue to appear.
3rd Whenever pressing the @, #, $, %, ^, *, (, ), 1, 2 button, the number increases from
0~9(0123456789) and A, b, c, d, E, F each time.
TROUBLESHOOTING
! If the first number is , it is correct otherwise press until
appear.
@ When pressing the button ~ appear on the display, select one of them.
# When pressing the button ~ appear on the display, select one of them.
$ When pressing the button ~ appear on the display, select one of them.
% When pressing the button ~ appear on the display, select one of them.
^ When pressing the button ~ appear on the display, select one of them.
DB00_00000A(1)_57~ 3/27/03 2:30 PM Page 96
Andrey Chebotarev
Premium
SAMSUNG | 98
1TROUBLESHOOTING 8Set up the Model Option (Cont.)
Step 3 : Reconfirming option set after completion
(in case of ex. 017d25-17021d)
After pressing selector for the mode, the display shown as .
After pressing selector for the mode, the display shown as .
Step 4 : Pressing the ON/OFF button ( )When pressing the operation ON/OFF key with the direction of remote controller for unit, the sound “Ding” or “Diriring” is
heard and the OPERATION LED lamp is flickering at the same time, then the input of option is completed.
(If the diriring sound isn’t heard, try again pressing the ON/OFF button.)
Step 5 : Unit operation test-runFirst, Remove the battery from the remote controller.
Second, Re-insert the battery into the remote controller.
Third, Press ON/OFF key with the direction of remote controller for set.
! If the first number is , it is correct otherwise press until
appear.
@ When pressing the button ~ appear on the display, selectone of them.
# When pressing the button ~ appear on the display, selectone of them.
$ When pressing the button ~ appear on the display, select oneof them.
% When pressing the button ~ appear on the display, select oneof them.
^ When pressing the button ~ appear on the display, select oneof them.
Error Mode :
1st If all lamps of indoor unit are flickering, Plug out and plug in again and pressing ON/OFF key to retry.
2nd If the unit is not working properly or all lamps are continuously flickering after setting the option code, seeif the correct option code is set up for it’s model.
DB00_00000A(1)_57~ 3/27/03 2:30 PM Page 97
Andrey Chebotarev
Premium
Samsung Electronics10
Feature Display
3. Set Up the Model Option
3-1 Setting Option Setup Method
Option No. : (SH12AWH)
Step 1 : Enter the Option Setup mode.
1st Take out the batteries of remote control.
2nd Press the temperature button simultaneously and insert the battery again.
3rd Make sure the remocon display shown as .
Step 2 : Enter the Option Setup mode and select your option according to the following procedure.
3
1,4 2,5
Setting Option SEG1.
Push the button to set the display panel to .
Every time you push the button, the display panel reads . . . repeatedly.
2Setting Option SEG2.
Push the button to set the display panel to .
Every time you push the button, the display panel reads . . . repeatedly.
4Setting Option SEG3.
Push the button to set the display panel to .
Every time you push the button, the display panel reads . . . repeatedly.
3Change it into the set display of Option SEG3 and SEG4
with the button.
5Setting Option SEG4.
Push the button to set the display panel to .
Every time you push the button, the display panel reads . . . repeatedly.
1
DB98_15924A(2)_1 04/3/8 11:29 AM Page 10
Set Up the Model Option
11Samsung Electronics
Feature Display
7Setting Option SEG5.
Push the button to set the display panel to .
Every time you push the button, the display panel reads . . . repeatedly.
6Change it into the set display of Option SEG5 and SEG6
with the button.
8Setting Option SEG6.
Push the button to set the display panel to .
Every time you push the button, the display panel reads . . . repeatedly.
10Setting Option SEG7.
Push the button to set the display panel to .
Every time you push the button, the display panel reads . . . repeatedly.
9Change it into the set display of Option SEG7 and SEG8
with the button.
11Setting Option SEG8.
Push the button to set the display panel to .
Every time you push the button, the display panel reads . . . repeatedly.
13Setting Option SEG9.
Push the button to set the display panel to .
Every time you push the button, the display panel reads . . . repeatedly.
12Change it into the set display of Option SEG9 and SEG10
with the button.
14Setting Option SEG10.
Push the button to set the display panel to .
Every time you push the button, the display panel reads . . . repeatedly.
6,9
7,10 8,11
12
13 14
DB98_15924A(2)_1 04/3/8 11:30 AM Page 11
Set Up the Model Option
Samsung Electronics12
Step 3 : Upon completion of the selection, check you made right selections.Whenever you press the button, the set Option will be displayed.
Step 4 : Pressing the ON/OFF button ( )When pressing the operation ON/OFF key with the direction of remote controller for unit, the sound "Ding" is heard and theOPERATION LED lamp is flickering at the same time, then the input of option is completed. (If the "ding" sound isn't heard,try again pressing the ON/OFF button.)
Step 5 : Unit operation test-runFirst, Remove the battery from the remote controller.Second, Re-insert the battery into the remote controller.Third, Press ON/OFF ( ) key with the direction of remote controller for set.
• Error Mode
1st If all lamps of indoor unit are flickering, Plug out, plug in battery again and press ON/OFF key to retry.
2nd If the unit is not working properly or all lamps are continuously flickering after setting the option code, see if thecorrect option code is set up for its model.
DB98_15924A(2)_1 04/3/8 11:30 AM Page 12
SAMSUNG | 99
1TROUBLESHOOTING 8Set up the Model Option (Cont.)
<Table of the option code>
MODEL
SH12ZSG
SH09ZS8
SH07ZS8
OPTION CODE
066025-172362
027064-17221d
026064-1720Fb
◆ Non Inverter (7K/ 9K/ 12K)
DB98_08187A(1)_57~100 3/27/03 2:24 PM Page 97
Andrey Chebotarev
Standart
100 | SAMSUNG
8Set up the Model Option (Cont.)
<Table of the option code>
MODEL
SH12ZPG
SH09ZPG
SH07ZPG
OPTION CODE
067066-170362
026566-170340
026065-17022E
◆ Non Inverter (7K/ 9K/ 12K)
TROUBLESHOOTING
DB00_00000A(1)_57~ 3/27/03 2:30 PM Page 98
Andrey Chebotarev
Premium
<Table of the option code>
MODEL
AS09A3ME
SC09ZA3/A
AS07A3ME
SC07ZA3/A
AS09A4ME
SCO9ZA4/A
AS07A4ME
SCO7ZA4/A
AS12A1ME
SC12ZA1/A
AS09A1ME
SC09ZA1/A
AS07A1ME
SC07ZA1/A
AS12A2ME
SC12ZA2/A
AS09A2ME
SCO9ZA2/A
AS07A2ME
SCO7ZA2/A
OPTION CODE
010000-1700d9
010000-1700b7
000000-1700d9
000000-1700b7
010000-17021d
010000-1700d9
010000-1700b7
000000-17021d
000000-1700d9
000000-1700b7
◆ Non Inverter Cooling Only (7K/ 9K/ 12K)
Troubleshooting 136
100-139* 2/19/01 2:29 PM Page 136
MODEL
AQV12Y6ME
AQV09Y6ME
OPTION CODE
007510-10723F
007500-1070Fb
<Table of the option code>
◆ Inverter (9K/ 12K)
Troubleshooting 138
100-139* 2/19/01 2:29 PM Page 138
<Table of the option code>
◆ Non Inverter Cooling Only & Heat pump (18K/ 24K)