Ver.2.32 Ver.2.32
Ver.2.32Ver.2.32
Even a little dust or moisture will affect an air tool to stop operation in some cases.Thus, an air-filter(Drain separator)and lubricator should always be equipped in the piping and also the oil in the lubricator should be checked.
Air tool parts are precision machined items. Throwing, dropping or rough handling is strictly prohibited.Periodical inspection will increase the durability performance and efficiency of the air tool.Check air line frequently making sure clean air is being sent to the tool.
E-mail : [email protected]
812-0043, Japan
Kiyama Plant
OPERATION AND MAINTENANCE INSTRUCTIONS FOR AIR TOOLS
Air Compressor
Lubrication
Dust-Proof and Anti-Corrosion
Maintenance and Periodical inspection
Air tool is greatly affected for its durability, performance and work efficiency by the way of operation and maintenance.The following instructions should carefully be obeyed in order to maintain the performance of new tool.
Air tool is designed to be operated at dynamic air pressure of 5-7 kg/cm² on the pressure gauge. During operation, the air consumption is shown in the specifications for each tool. Thus the air distribution volume of an air-compressor should be larger than the total air-consumption of the tools under simultaneous use.Preferably, the air distribution volume should be 20% more than total air consumption.This is due to the loss of air and decrease in air pressure through piping. In general, the compressor to be installed to distribute 1m³ /min should have 10HP engine.The lack of air volume results in a decrease of performance for air tool. The air compressor, therefore, should have some allowance in capacity.
Lubrication is very important for air tool operation. All Toku air tool is tested before delivery. However, if a defective situation or poor performance is experienced, please be sure to clean off the air tool oil by washing oil or putting a small volume of the lubricant(shown below) in the tool. Restart at slow speed gradually.Recommended lubricants and instruction for lubrication is mentioned below.
other Hammers
Rotary Hammers
moving surface ofvalve and piston etc
Turbine oil(ISOVG-46 or equivalent)
3cc/min by line oiler
2001FSP2000
EMS 89393/ISO 14001
ASPHALTCUTTER
Forged body for long life.
Automatic push-start mechanism.Less components for easy maintenance. Replaceable round bushing.
OPTIONALMUFFLER
OPTIONALMUFFLER
OPTIONALMUFFLER
OPTIONALMUFFLER
7/8×3-1/4 or 1×4-1/4577
7/8×3-1/4 or 1×4-1/4
TPB-40SV
19.5 43 653.5TPB-40SV
PICKHAMMER
TRENCHER&CLAYDIGGER
TCBBREAKER
TPBBREAKER
166 1,050 20.9 46
606 1.6
1.5
56.5
53
16
66.6
40
62
68
93 725
1.65 58.3
● 2types of retainer, cup and spring, are available.(THA-4B)● Four bolt handle for excellent durability and maintenance.(TCH-3&4)
THA-2B THA-3B
Goose Neck Handle 4-Bolt Handle
THA-4B THA-4S TCH-3 TCH-4
51
64
102
63.5
101.6
2,300
2,200
1,800
2,200
1,800
6.2
6.8
7
8.6
9
13.6
15
16.1
19
20
413
450
480
406
432
0.85
0.9
0.95
0.89
0.95
30
31.8
33.5
31.5
33
22.5 50
41
31
17.8 567
583
THA-2B
THA-3B
THA-4B(S)
TCH-3
TCH-4
TJ-20SV
INSERT BIT FOR ROTARY HAMMER
TJ-20SV
250,280,400,500,600,700
AACHIPPINGHAMMER
for AA-1.3B.
CHIPPINGHAMMER
SINKERROCKDRILL
ROTARYHAMMER
64 60
● Water swivel attachment available to control dust and chips from drilling.
18 40 38.9
4.0
Water swivel
Air swivel complete
Wet shank
Dry shank
Rod size 500, 1000, 1200, 1500mm
Rod connection
Bit (Thread type)Gauge size42, 48, 50, 55, 65mm
Spiral rod (Thread type)
TAA-400
PUT OUTmm
1,200 600-950 10.2 22.5 275 3.4 119 19 3/4 LEVER TYPE
SPEED AT NO LOADr.p.m
SPEED AT LOADr.p.m
START TYPE
ACCESSORIES FOR AUGER DRILL
TAMPER & SAND RAMMER
AIR AUGER DRILL
TAA-400
600
TAMPER&SANDRAMMER
ROD CHISEL
TAMPINGROD AND PAD
AIRAUGERDRILL
BIT
HOSECOUPLING
● Water swivel attachment available to control dust and chips from drilling.
18 40 38.9
4.0
Water swivel
Air swivel complete
Wet shank
Dry shank
Rod size 500, 1000, 1200, 1500mm
Rod connection
Bit (Thread type)Gauge size42, 48, 50, 55, 65mm
Spiral rod (Thread type)
TAA-400
PUT OUTmm
1,200 600-950 10.2 22.5 275 3.4 119 19 3/4 LEVER TYPE
SPEED AT NO LOADr.p.m
SPEED AT LOADr.p.m
START TYPE
ACCESSORIES FOR AUGER DRILL
TAMPER & SAND RAMMER
AIR AUGER DRILL
TAA-400
600
TAMPER&SANDRAMMER
ROD CHISEL
TAMPINGROD AND PAD
AIRAUGERDRILL
BIT
HOSECOUPLING
Ver.2.31
Even a little dust or moisture will affect an air tool to stop operation in some cases.Thus, an air-filter(Drain separator)and lubricator should always be equipped in the piping and also the oil in the lubricator should be checked.
Air tool parts are precision machined items. Throwing, dropping or rough handling is strictly prohibited.Periodical inspection will increase the durability performance and efficiency of the air tool.Check air line frequently making sure clean air is being sent to the tool.
E-mail : [email protected]
812-0043, Japan
Kiyama Plant
OPERATION AND MAINTENANCE INSTRUCTIONS FOR AIR TOOLS
Air Compressor
Lubrication
Dust-Proof and Anti-Corrosion
Maintenance and Periodical inspection
Air tool is greatly affected for its durability, performance and work efficiency by the way of operation and maintenance.The following instructions should carefully be obeyed in order to maintain the performance of new tool.
Air tool is designed to be operated at dynamic air pressure of 5-7 kg/cm² on the pressure gauge. During operation, the air consumption is shown in the specifications for each tool. Thus the air distribution volume of an air-compressor should be larger than the total air-consumption of the tools under simultaneous use.Preferably, the air distribution volume should be 20% more than total air consumption.This is due to the loss of air and decrease in air pressure through piping. In general, the compressor to be installed to distribute 1m³ /min should have 10HP engine.The lack of air volume results in a decrease of performance for air tool. The air compressor, therefore, should have some allowance in capacity.
Lubrication is very important for air tool operation. All Toku air tool is tested before delivery. However, if a defective situation or poor performance is experienced, please be sure to clean off the air tool oil by washing oil or putting a small volume of the lubricant(shown below) in the tool. Restart at slow speed gradually.Recommended lubricants and instruction for lubrication is mentioned below.
other Hammers
Rotary Hammers
moving surface ofvalve and piston etc
Turbine oil(ISOVG-46 or equivalent)
3cc/min by line oiler
1810FSP2000
EMS 89393/ISO 14001
ASPHALTCUTTER
Ver.2.32
Even a little dust or moisture will affect an air tool to stop operation in some cases.Thus, an air-filter(Drain separator)and lubricator should always be equipped in the piping and also the oil in the lubricator should be checked.
Air tool parts are precision machined items. Throwing, dropping or rough handling is strictly prohibited.Periodical inspection will increase the durability performance and efficiency of the air tool.Check air line frequently making sure clean air is being sent to the tool.
E-mail : [email protected]
812-0043, Japan
Kiyama Plant
OPERATION AND MAINTENANCE INSTRUCTIONS FOR AIR TOOLS
Air Compressor
Lubrication
Dust-Proof and Anti-Corrosion
Maintenance and Periodical inspection
Air tool is greatly affected for its durability, performance and work efficiency by the way of operation and maintenance.The following instructions should carefully be obeyed in order to maintain the performance of new tool.
Air tool is designed to be operated at dynamic air pressure of 5-7 kg/cm² on the pressure gauge. During operation, the air consumption is shown in the specifications for each tool. Thus the air distribution volume of an air-compressor should be larger than the total air-consumption of the tools under simultaneous use.Preferably, the air distribution volume should be 20% more than total air consumption.This is due to the loss of air and decrease in air pressure through piping. In general, the compressor to be installed to distribute 1m³ /min should have 10HP engine.The lack of air volume results in a decrease of performance for air tool. The air compressor, therefore, should have some allowance in capacity.
Lubrication is very important for air tool operation. All Toku air tool is tested before delivery. However, if a defective situation or poor performance is experienced, please be sure to clean off the air tool oil by washing oil or putting a small volume of the lubricant(shown below) in the tool. Restart at slow speed gradually.Recommended lubricants and instruction for lubrication is mentioned below.
other Hammers
Rotary Hammers
moving surface ofvalve and piston etc
Turbine oil(ISOVG-46 or equivalent)
3cc/min by line oiler
2001FSP2000
EMS 89393/ISO 14001
ASPHALTCUTTER