This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
TOOL AND SUPPLIES REQUIREDPhillips screwdriverStubby #2 Phillips screwdriver10 mm SocketRatchetDiagonal cutters10 mm Combination wrenchDrill3 mm, 6 mm, 7 mm, 10 mm, Drill bitEye protection (face shield, safety goggles, etc.)Hacksaw bladeFileMasking tapeFlat-tip screwdriverFelt-tip penPushpinBlanketIsopropyl alcoholShop towelScissors
3 Wire ties with clip
4 Small wire ties
Switch
2 Washer-bolts, 6 x 16 mm
2 Washer-bolts, 5 x 16 mm
6 Self-tapping screws
Ground bolt
4 Cushion tapes
Fuse label(LX model only)
10A Fuse
INSTALLATION
Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These proceduresshould not be attempted by “do-it-yourselfers.”
NOTE:
• Be careful not to damage the body finish.
• Take care not to damage the clips and tabs.
1. Make sure you have the anti-theft code for theradio, then write down the radio station presets.
2. Disconnect the negative cable from the battery.
3. Remove the radiator cover (ten clips). Cutting the Front Bumper
5. To protect the bumper, apply masking tape to thefront side of the bumper around the right and leftfog light opening.
4. Remove the front bumper.
• On each side, pull the inner fender back, andremove the two self-tapping screws.
• Remove the eight clips.
• Remove the two bolts, and remove the frontbumper.
• Place the front bumper on a blanket.
6. On the inside of the bumper, align the templatewith the left fog light mounting position. Using apushpin, mark the bumper at each of the sixlocations on the template. Ignore the pre-scribedline.
11. On the inside of the front bumper, cut out the foglight opening from the front bumper using ahacksaw blade. Remove any burrs, and removethe masking tape.
10. On the outside of the front bumper, use ahacksaw blade to cut the bumper at the fog lightopening along the three sides.
7. Using a felt-tip pen, mark the bumper in the areashown.
NOTE: If there are pre-scribed lines on thebumper, ignore the pre-scribed lines, and use thetemplate as the guide.
9. While wearing eye protection, drill one 7 mm holeand four 10 mm holes at the marked locations.Start with a 3 mm drill bit, and finish with a 7 mmor a 10 mm drill bit.
8. Turn the template over, and mark the other side ofthe bumper the same way.
4306052Y
FOG LIGHTOPENING
INSIDE THEFRONT BUMPER
PUSHPINMARK
CUT LINE
4306042Y
FRONT BUMPER
FOG LIGHTOPENING
HACKSAWBLADE
4306031Y
DRILL(Drill with 3 mmdrill bit, finish witha 10 mm drill bit.)
DRILL(Drill with 3 mmdrill bit, finish witha 10 mm drill bit.)
36. Below the under-hood fuse relay box, secure thefog light harness connector to the vehicleharness using the wire tie with holder, and trim thewire tie.
39. Secure the fog light harness connector to thevehicle harness using one wire tie.
32. Get the fog light harness. Plug the 1-pin white/green and the 1-pin red/green terminals into theback of the 18-pin connector in the locationsshown.
35. Reinstall the under-hood fuse relay box lowercover in the original position.
33. Reconnect the vehicle 18-pin connector into theunder-hood fuse relay box.
34. Plug the connector on the long/short subharnessinto the fog light harness connector. Secure thefog light harness and the subharness to thevehicle harness with one small wire tie, then trimthe wire tie.
4308091Y
LONG SUBHARNESS(EX/Touringmodel)
FOG LIGHT HARNESSCONNECTOR
SMALLWIRE TIE
FOG LIGHTHARNESS
VEHICLEHARNESS
SHORT SUBHARNESS(LX model)
37. Using isopropyl alcohol, thoroughly clean theareas where the cushion tape will attach. Usingscissors, cut one cushion tape in half, and attachone half to the FI-ECU in the area shown.
38. Locate the vehicle 2-pin connector blue taped tothe vehicle harness, and remove the blue tape tofree the connector. Plug the fog light harness 2-pinconnector into the vehicle harness 2-pinconnector.
40. Route the fog light harness forward along thevehicle harness. Loosely secure it to the vehicleharness with two wire ties.
41. Route the right fog light harness 2-pin connectoralong the vehicle harness and into the bumperarea.
42. Attach the two wire ties with clips on the fog lightharness into the holes in the vehicle body.
4309030Y
WASHERTANK
FOG LIGHTHARNESS
LOOSELYSECUREWITHWIRE TIE
RIGHTHEADLIGHT
VEHICLEHARNESS
4309040Y
HORN
FOG LIGHTHARNESS
VEHICLEHARNESS
43. Using isopropyl alcohol, thoroughly clean theareas where the cushion tape will attach. Securethe fog light harness to the vehicle’s frame withthe cushion tape.
44. Adjust the fog light harness until the green tape onthe fog light harness is close to the wire tie withclip on the vehicle harness. Secure the fog lightharness to the vehicle harness with two wire ties.
48. Route the fog light harness along the vehicleharness. Attach the fog light harness to thevehicle harness with two wire ties.
49. Route the fog light harness along the vehicleharness on the bulkhead, and loosely attach thefog light harness to the vehicle harness with fourwire ties.
4309080Y
WIRE TIE
FRONT
VEHICLEHARNESS
FOG LIGHTHARNESS
WIRE TIE
45. Tighten the two wire ties installed in step 40.
4309070Y
POWERSTEERINGRESERVOIRVEHICLE
BRACKET
4309030Y
WIRETIE
VEHICLEHARNESS
FOG LIGHTHARNESS
46. Reinstall the under-hood fuse/relay box.
47. Remove the power steering reservoir from thevehicle bracket.
50. Route the fog light harness behind the battery, andloosely secure it to the vehicle harness with threeadditional wire ties.
51. Locate the wire tie with clip near the end of the foglight harness. Wrap a cushion tape around the foglight harness at the measurement shown.
52. Attach the wire tie with clip on the fog lightharness into the hole in the body panel.
4310010Y
WIRE TIEWITH CLIP
WIRETIEWITHCLIP
120 mm
CUSHION TAPE
BODYPANEL
FOG LIGHTHARNESS
53. Route the fog light harness as shown.
55. EX model with AUTO air: Remove the bolt fromthe vehicle bracket. Secure the ground terminalfrom the fog light harness to the vehicle bracketusing the ground bolt supplied.
54. EX model with AUTO air: Secure the fog lightharness to the sensor harness with three wire ties.
61. Plug the blue fog light harness 4-pin connectorinto the gray relay. Plug the brown fog lightharness 4-pin connector into the black relay.
59. Tighten the seven wire ties installed in steps 49and 50.
60. Get the relay bracket and the two relays. Attachthe relays to the relay bracket with two 6 x 16 mmwasher bolts.
56. LX Model: Route the fog light harness as shownand secure it with three wire ties with clips to thevehicle frame.
58. Using isopropyl alcohol, thoroughly clean the areawhere the cushion tape will attach. Secure the foglight harness to the vehicle frame with onecushion tape.
57. LX Model: Use the ground bolt to secure theground terminal on the fog light harness to thevehicle frame.
62. Loosen the bolt that secures the existing relaybox, and slide the tab from the fog light relaybracket under the bolt. Retighten the relaybracket bolt.
63. Secure the fog light harness to the vehicleharness with three wire ties.
64. With the help of an assistant, plug the fog lightharness 2-pin connectors into the fog lightconnectors, and reinstall the front bumper in itsoriginal position. Be careful that the fog lightharness does not get caught between the bumperand the splash shield.
Installing the Fog Light Switch
65. Remove the instrument side panel (six clips, threeretaining tabs).
72. Route the 6-pin switch harness connector throughthe switch hole and plug it into the VSA switch.Plug the vehicle 6-pin VSA connector into theswitch harness.
66. Reaching through the opening in the dashboard,release the four clips and pull out on the switchpanel. If equipped, disconnect the vehicleconnectors from the switch panel, and remove theswitch panel.
68. Remove the VSA switch. (two retaining tabs).
70. Route the switch harness 5-pin connector throughthe switch hole and plug it into the fog light switch.
71. Install the fog light switch into the hole where youremoved the switch lid.
69. Unplug the vehicle 6-pin connector from the VSAswitch.
74. Locate the 2-pin connector at the front of the fusebox that is black-taped to the vehicle harness nearthe front bulkhead. Remove the black tape to freethe connector. Plug the 2-pin connector from theswitch harness into the vehicle harness 2-pinconnector you just freed.
73. Route and fold the switch harness back along thevehicle harness, and secure the switch harness tothe vehicle harness with two wire ties.
76. Install the 10A fog light fuse.
EX/Touring Model: Install the 10A fuse into thesubfuse box in the location shown.
75. At the fuse box, secure the switch harness to thevehicle harness with three wire ties.
• Adjust the aiming according to local laws andregulations.
• To adjust, turn the adjustment screw in or outuntil the correct aiming is obtained.
Fog Light Aiming Adjustment
86. Remove the bolt and clip, and pull down the innerfender.
USE AND CARE
How to Operate Fog Lights
• Turn the light switch to the “on” position (headlights on low beam ).
• Press the fog light switch (indicator is on).
• If the fog lights don’t come on, check the fuse andall the connectors, including the ground cable andthe fusible link.
NOTE: The fog light lenses can cloud when theoutside temperature is cold; this is normal and shouldgo away in warm weather.
Replacing the Bulb
NOTE:
• Use only a Honda Genuine Halogen Light Bulb ofspecified wattage.BULB, FOG LIGHT (H8)P/N 33165-S5A-J010-M1
• Do not touch the bulb. Oily or greasy substanceson the bulb can shorten its service life due to theheat produced when the bulb is turned on. If thebulb is accidentally touched, wipe it clean with aclean, soft cloth that has been dampened withdenatured alcohol or a mild detergent solution.
4. Unplug the connector from the bulb, and removethe bulb from the fog light.
1. Remove the bolt and clip, and pull down the innerfender.
2. Unplug the connector from the fog light.
3. Remove the screw that fastens the fog light, andpull the light out toward you.
6. Reinstall the removed parts in the reverse order ofremoval:
• Check that the wire harnesses are notpinched.
• Be sure to tighten the self-tapping screw andbolts securely.
7. Check the operation of the fog light; adjust theaiming if necessary.
4312010Y
FOG LIGHT
BULBCONNECTOR
4311110Y
FOG LIGHT
BULBCONNECTOR
4311100Y
FOG LIGHT
SCREW CONNECTOR
4311070Y
Pull down.CLIP BOLT
INNER FENDER5. Install the new bulb into the fog light. Align the tab
on the fog light with the cutout in the bulb socketwhen installing the new bulb. If not aligned, thereis possibility that the fog light may annoyoncoming drivers.