AII 24282 CD Changer - HandA- · PDF fileCD CHANGER ELEMENT PARTS LIST ... AII 24282. ... 28. Remove the clip that secures the vehicle harness With side Air Bag:
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
6. Remove the passenger’s lower dashboard cover(disengage the three clips, and disconnect the twopins).
4. Remove the four self-tapping screws and pull outthe audio unit.
5. Disconnect the vehicle connector (threeconnectors on EX model) and the antenna lead,then remove the audio unit.
INSTALLATION
Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These proceduresshould not be attempted by “do-it-yourselfers.”
1. Make sure you have the anti-theft code for theradio, then write down the frequencies for thepreset buttons.
2. Disconnect the negative cable from the battery.
3. Wrap the shop towel to the top of the flat-tipscrewdriver, and insert it to grooves in the audiopanel. Pull the audio panel out toward you torelease the five clips and remove the audio panel.Take care not to damage the clips.
11. Remove the two front bolt covers, then removethe four bolts that fasten the passenger’s seatside rails so that the passenger’s seat can belifted.
10. Behind the passenger’s seat, remove the clipsthat fasten the rear cover to the vehicle panel andremove the cover. Take care not to damage theclips.
9. Remove the left recline cover from thepassenger’s seat (self-tapping screw and twoclips).
8. Remove the knob from the recline lever. Removethe two clips and remove the right recline coverfrom the passenger’s seat.
7. Open the glove box and remove the two stoppersby releasing the two retaining tabs for eachstopper. Remove the two screws that fasten theglove box, and remove the glove box.
14. From the center dashboard opening, route theBUS cable toward the glove box opening alongthe antenna lead.
13. Pull up the door opening trim, and remove thepassenger’s kick panel (pull the kick panel outtoward you to release the two clips and twohooks). Take care not to damage the clips andhooks.
12. Remove the passenger’s sill trim (ten clips andtwo retaining tabs). Take care not to damage theclips and retaining tabs.
2710010K
CLIPS (10) PASSENGER’SSILL TRIM RETAINING
TAB
RETAININGTAB
2710020K
PASSENGER’SKICK PANEL
HOOK
CLIPS (2)
DOOROPENINGTRIM
2710052K
ANTENNALEAD
WIRE TIE
BUS CABLE14-PIN CONNECTOR(Align the BUS cable14-pin connector withthe antenna lead.)
VEHICLECONNECTOR
AUDIO(Take care to avoidcontact with theaudio unit.)
VEHICLEHARNESS
BUSCABLE
BUS CABLE14-PINCONNECTOR
15. Pull the BUS cable 14-pin connector out from thecenter dashboard opening and adjust the cable sothat the distance from the center dashboardopening to the end of the 14-pin connector is100 mm. Secure the BUS cable to the vehicleharness with one wire tie as shown.
Using isopropyl alcohol, thoroughly clean thevehicle panel in the area shown, then secure theBUS cable to the vehicle panel with the twocushion tapes.
17. Continue routing the BUS cable downward andattach it with wire ties or cushion tape.
With Amplifier:
Secure the BUS cable to the amplifier harnesswith the wire ties in the areas shown.
16. Continue routing the BUS cable along thedashboard frame, and secure it to the antennalead with the four wire ties in the areas shown.Point the connection part of the two wire tiesupward as shown.
21. Turn over the floor covering. Make loops in theBUS cable, then secure the loops to the vehicleharness with the two wire ties in the areas shown.
19. Using isopropyl alcohol, thoroughly clean the areawhere the four cushion tapes will be attached.Secure the BUS cable to the vehicle panel withthe cushion tapes.
20. Adjust the BUS cable so that the distance fromthe end of the 14-pin connector to the hole in thefloor covering is 330 mm.
18. Route the BUS cable toward the rear of thevehicle along the side step and under the floorcovering to the passenger’s seat, then out throughthe hole in the floor covering.
• Route the BUS cable as shown.
2710081K
SIDESTEP
CUSHIONTAPE
REARWINDSHIELDWASHER TUBE
FLOORCOVERINGHOLE
BUSCABLE
30 mm 40 mm
FRONT
FRONT
PASSENGER’SSIDE SEAT
BUSCABLE
Installing the CD Changer
22. Visually check the location of the spring adjustingknobs on both sides of the CD changer. Thespring adjusting knob should be in the horizontalposition (H). If the knobs are in the verticalposition (V), adjust them to the horizontal position.
24. Attach the two harness clips to the CD changerand the harness clamp bracket you just installedusing the two 4 x 8 mm washer-screws.
23. Position the harness clamp bracket on the CDchanger and install the 4 x 8 mm washer-screw.
27. Release the passenger’s seat cushion (ninehooks). Lift the the seat cushion.
26. Position the CD changer brackets on the sides ofthe CD changer, then install the four 4 x 8 mmwasher-screws and tighten securely.
25. Wrap one EPT sealer around the BUS cableconnector from the CD changer, then secure theBUS cable and connector to the CD changer withthe harness clips you just installed.
2710121K
EPT SEALER
HARNESSCLIP
CD CHANGERBUS CABLE
MAKE SURE THECONNECTOR ISPOSITIONED IN THEDIRECTION SHOW
With side Air Bag:28. Remove the clip that secures the vehicle harnessconnector to the seat panel.
ï Relocate the connector on the seat panel in thearea shown.
ï Slide the clip of the vehicle connector (gray) offthe seat panel by pushing it with a small flat-tipscrewdriver, then install the connector clip fromthe kit on the vehicle connector (gray) in the newdirection.
ï Relocate the vehicle connector (gray) to the seatpanel in the new area shown.
Without side Air Bag:
2923010K
SEATPANEL
VEHICLECONNECTOR(GRAY)
SEAT PANEL
VEHICLECLIP
Remove theclip with asmall flat-tipscrewdriver
VEHICLE CONNECTOR(GRAY)
CONNECTORCLIP
2711052K
VEHICLE HARNESSCONNECTOR
SEAT PANEL
VEHICLECONNECTOR(GRAY)
VEHICLEHARNESSCONNECTOR
SEAT PANEL
VEHICLECLIP
Remove theclip with aprecisionflat-tipscrewdriver.
34. Install one wire tie with clip to the right basebracket and attach the vehicle harness.
31. Insert the studs from the CD changer plate intothe elongated holes in the seat panel.
32. Tighten the two 6 mm flange nuts.
• Take care not to injure your hands with theburrs and sharp edges of the inside of the seatpanel.
29. Cut two EPT sealers to 70 mm and 90 mm asshown.
30. Remove the harness clip shown in the figure fromthe seat panel. Wrap the cut EPT sealers aroundthe vehicle harness. Then reinstall the harnessclip in its original position.
• Please keep the cut EPT sealer, it will bereused.
2711060KViewed with seat upside down
6 mmFLANGE NUT
SEAT PANELELONGATEDHOLE
CD CHANGERPLATE
SEATCUSHION
(FRONT)
2903110K
RIGHT BASEBRACKET
VEHICLE HARNESSCONNECTOR
WIRE TIEWITH CLIP
2903100K
EPTSEALER 90 mm 70 mm
Temporarily remove.
Reuse.
WITHSIDEAIRBAGS
WITHSIDEAIRBAGS
33. Prepare the seat base.
ï Use the excess EPT sealer from the 70 mm cutand wrap it around the right base bracket.
ï Attach the right and left base brackets to the seatpanel with the two 5 x 26 mm self-tapping screwsand two 6 x 12 mm washer-bolts.
ï Insert the two self-tapping screws into the holes inthe screw grommets, and 6 x 12 mm washer-boltsinto the nuts welded on the CD changer plate.
ï Push the two screw grommets into the rear squareholes of the seat panel from the bottom side.
36. Position the CD changer on the right and leftbrackets then install the four 6 mm flange nutsand tighten securely.
35. Attach the excess EPT sealer from the 90 mm cutto the harness clamp bracket.
38. Temporarily tighten the four seat mounting bolts.Slide the seat back and forth to check that theBUS cable is not pulled too tight and does bind.
37. Plug the BUS cable connector into the CDchanger, and secure the BUS cable to the harnessclamp bracket with one wire tie with clip in thearea shown.