Adaptive Configuration of Typical HSPA Rate(RAN14.0_03)

5/25/2018 Adaptive Configuration of Typical HSPA Rate(RAN14.0_03)

1/18

Adaptive Configuration of Typical HSPA RateRAN14.0

Feature Parameter Description

Issue 03

Date 2013-05-10

HUAWEI TECHNOLOGIES CO., LTD.


2/18

Copyright Huawei Technologies Co., Ltd. 2013. All rights reserved.

No part of this document may be reproduced or transmitted in any form or by any means without prior

written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective

holders.

Notice

The purchased products, services and features are stipulated by the contract made between Huawei and

the customer. All or part of the products, services and features described in this document may not be

within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,

information, and recommendations in this document are provided "AS IS" without warranties, guarantees orrepresentations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base

Bantian, Longgang

Shenzhen 518129

People's Republic of China

Website: http://www.huawei.com

Email: [email protected]
http://www.huawei.com/http://www.huawei.com/mailto:[email protected]:[email protected]:[email protected]://www.huawei.com/


3/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate Contents

Issue 03 (2013-05-10) Huawei Proprietary and Confidential Copyrig


i

Contents

1 Introduction................................................................................................................................ 1-11.1 Scope ............................................................................................................................................ 1-11.2 Intended Audience......................................................................................................................... 1-11.3 Change History .............................................................................................................................. 1-1

2 Overview...................................................................................................................................... 2-13 Principles.................................................................................................................................... 3-1

3.1 Overview ....................................................................................................................................... 3-13.2 Typical Traffic Rate ........................................................................................................................ 3-13.3 Rate Matching Rules ..................................................................................................................... 3-13.4 Rate Matching Procedure ............................................................................................................. 3-2

4 Related Features....................................................................................................................... 4-14.1 Prerequisite Features .................................................................................................................... 4-14.2 Mutually Exclusive Features ......................................................................................................... 4-14.3 Impacted Features ........................................................................................................................ 4-1

5 Network Impact.......................................................................................................................... 5-15.1 System Capacity ........................................................................................................................... 5-15.2 Network Performance ................................................................................................................... 5-1

6 Engineering Guidelines........................................................................................................... 6-16.1 When to Use Adaptive Configuration of Typical HSPA Rate ......................................................... 6-16.2 Feature Deployment ...................................................................................................................... 6-1

6.2.1 Prerequisites ......................................................................................................................... 6-16.2.2 Data Preparation................................................................................................................... 6-16.2.3 Precautions ........................................................................................................................... 6-16.2.4 Activation Procedure ............................................................................................................. 6-16.2.5 Verification Procedure .......................................................................................................... 6-26.2.6 Deactivation Procedure ........................................................................................................ 6-26.2.7 Example ................................................................................................................................ 6-2

7 Parameters.................................................................................................................................. 7-18 Counters...................................................................................................................................... 8-19 Glossary...................................................................................................................................... 9-110 Reference Documents......................................................................................................... 10-1


4/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate 1 Introduction

Issue 03 (2013-05-10) Huawei Proprietary and Confidential Copyright


1-1

1 Introduction

1.1 Scope

This document describes the feature WRFD-030004 Adaptive Configuration of Typical HSPA Rate.

1.2 Intended Audience

This document is intended for:

Are familiar with WCDMA basics

Need to understand the Adaptive Configuration of Typical HSPA Rate feature

Work with Huawei products

1.3 Change History

This section provides information about the changes in different document versions.

There are two types of changes, which are defined as follows:

Feature change: refers to a change in the feature Adaptive Configuration of Typical HSPA Rate of aspecific product version.

Editorial change: refers to a change in wording or the addition of information that was not described inthe earlier version.

Document Issue

The document issue is as follows:

03 (2013-05-10)

02 (2012-07-20)

01 (2012-04-30)

Draft A (2012-02-15)

03 (2013-05-10)

This is the document for the third commercial release of RAN14.0.

Compared with issue 02 (2012-07-20), this issue this issue incorporates the changes described in thefollowing table:

Change Type Change Description Parameter Change

Feature change None None

Editorial change Added the chapter4 "Related Features." None

02 (2012-07-20)

This is the document for the second commercial release of RAN14.0.

Compared with issue 01 (2012-04-30), this issue this issue incorporates the changes described in thefollowing table:


5/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate 1 Introduction



1-2

Change Type Change Description Parameter Change

Feature change None. None.

Editorial change Added the information about how to deploy Adaptive

Configuration of Typical HSPA Rate. For details, see6.2"Feature Deployment."

None.

01 (2012-04-30)

This is the first commercial release of RAN14.0.

Compared with issue Draft A (2012-02-15) of RAN14.0, this issue has no change.

Draft A (2012-02-15)

This is the first draft document for RAN14.0.This is a new document.


6/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate 2 Overview



2-1

2 Overview

With High Speed Packet Access (HSPA), mobile operators can provide services with diversified trafficrates. This is beneficial to mobile operators in many cases, such as in competing with fixed-line

operators and in justifying service fees. The typical traffic rates configured at the Radio NetworkController (RNC), however, are fixed and separated, and may be inconsistent with the maximum bit rates(MBRs) configured at the core network (CN).

If an inconsistency occurs, the RNC selects a typical traffic rate closest to the MBR assigned by the CN.This rate, not the MBR, is then used for calculating the actual maximum traffic rate of the UE. As a result,the rate used by the UE is inconsistent with the MBR configured at the CN, and user experience may beaffected.

With the feature Adaptive Configuration of Typical HSPA Rate, the RNC can calculate the actualmaximum traffic rate based on the MBR assigned by the CN when a traffic rate inconsistency occursbetween the RNC and CN. In this way, the rate assigned to the UE is consistent with the MBR configuredat the CN.

Figure 2-1 shows how this feature is implemented in the WCDMA system.

Figure 2-1 Feature implementation in the WCDMA system

Typical traffic rates refer to the MBRs configured at the RNC rather than the MBR assigned by the CN.


7/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate 3 Principles



3-1

3 Principles

3.1 Overview

The CN sends the MBR to the RNC using an RAB assignment request message; The RNC comparesthe MBR assigned by the CN, the maximum rate supported by the UE, the maximum rate supported bythe serving cell, and the rate specified in the license file, and selects the lowest of these four values. TheRNC uses the lowest value as MBRrnc. The RNC then maps the MBRrnconto a typical traffic rate.

Without the feature Adaptive Configuration of Typical HSPA Rate, if the MBRrnccannot be mapped ontoany typical traffic rate, the RNC selects the typical traffic rate closest to the MBRrnc. The RNC thenidentifies a Radio Access Bearer (RAB) index based on the MBR rncand the related attributes. Theseattributes are the CN domain, traffic class, source statistics descriptor, and direction. These attributesand RAB indexes are stored in the Traffic Radio Bearer (TRB) specifications table at the RNC. TheMBRrnccorresponding to the RAB index is the typical traffic rate. The RNC then sends the actualmaximum traffic rate calculated based on the typical traffic rate to the UE and configures the associated

parameters for the service based on the RAB index.

With this feature, if the MBRrnccannot be mapped onto any typical traffic rate, the RNC configures theassociated parameters for the service according to the traffic-bearing parameters for the typical trafficrate closest to the MBRrncand the rate assigned to the UE is consistent with the MBRrnc.

This feature is applicable only to best effort (BE) services over HSPA channels.

3.2 Typical Traffic Rate

The TRB specifications table lists the TRB specifications supported by Huawei RNCs. For details aboutTRB specifications, seeRadio Bearers Feature Parameter Description.

The MBRs of TRB specifications are the typical traffic rates configured at the RNC.

3.3 Rate Matching Rules

The RNC uses the MBR assigned by the CN to calculate the actual maximum traffic rate, and configuresthe associated parameters for the service according to the traffic-bearing parameters for the typicaltraffic rate closest to the MBRrnc.

Assume that the CN specified the MBR for interactive services in the uplink, The RNC compares theMBR assigned by the CN, the maximum rate supported by the UE, the maximum rate supported by theserving cell, and the rate specified in the license file, and selects the lowest of these four values. TheRNC uses the lowest value as MBRrnc. Assume that the MBRrncis 5440 kbit/s. The typical traffic rates atthe RNC that are close to 5400 kbit/s are 2720 kbit/s and 5440 kbit/s. The rate closest to 5400 kbit/s is

5440 kbit/s, which corresponds to RAB index 58. Without this feature, the rate assigned to the UE forinteractive services in the downlink is 5440 kbit/s. With this feature, the rate assigned to the UE is 5400kbit/s. In addition, the RNC configures the associated parameters for interactive services according tothe traffic-bearing parameters for RAB index 58.
http://localhost/var/www/apps/conversion/tmp/scratch_2/Radio%20Bearers.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/Radio%20Bearers.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/Radio%20Bearers.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/Radio%20Bearers.htm


8/18

WCDMA RAN




3-2

Figure 3-1 Rate matching result

If two typical traffic rates are equally close to the MBRrnc, the higher traffic rate is selected. For example,if the MBRrncis 4520 kbit/s, traffic rates 3600 kbit/s and 5440 kbit/s are equally close to the MBRrncand5440 kbit/s is selected.

3.4 Rate Matching Procedure

This feature is enabled when thePsSwitch parameter is set toHSPA_ADPTIVE_RATE_ALGO_SWITCH.

This feature can be provided in the uplink and downlink. The radio resources in the uplink and downlinkare separately allocated. The CN sends an uplink MBR and a downlink MBR. The RNC compares theMBR assigned by the CN, the maximum rate supported by the UE, the maximum rate supported by theserving cell, and the rate specified in the license file, and selects the lowest of these four values. TheRNC uses the lowest value as MBRrnc. The rate adaptive configuration procedure in the uplink is similarto that in the downlink.Figure 3-2 shows the rate adaptive configuration procedure based on theassumption that the MBRrncconfigured on the CN is 5400 kbit/s.

Figure 3-2 Rate adaptive configuration procedure

The 5400 kbit/s rate is used as an example.
http://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.html


9/18

WCDMA RAN




3-3

The rate adaptive configuration procedure is as follows:

1. The CN sends the RNC an RAB Assignment Request message, carrying a MBR.

2. The RNC compares the MBR assigned by the CN, the maximum rate supported by the UE, themaximum rate supported by the serving cell, and the rate specified in the license file, and selects the

lowest of these four values. The RNC uses the lowest value to calculate the actual maximum trafficrate. The RNC uses the lowest value as MBRrnc. Assume that the MBRrncis 5400 kbit/s.

3. The rate assigned to the UE is consistent with the MBR rnc. In addition, the RNC obtains thetraffic-bearing parameters for the typical traffic rate 5440 kbit/s, which is closest to 5400 kbit/s.

4. The RNC maps the MBRrnconto the MAC rate and sends the MAC rate to the NodeB.

5. Based on the MAC rate, the NodeB assigns resources to the UE.

6. An RAB connection is set up between the RNC and UE.

7. The UE transmits data at the MAC rate mapped from the MBRrnc. The data transmission is based onthe traffic-bearing parameters for the typical traffic rate 5440 kbit/s.


10/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate 4 Related Features



4-1

4 Related Features

4.1 Prerequisite Features

WRFD-010610 HSDPA Introduction Package

WRFD-010612 HSUPA Introduction Package

4.2 Mutually Exclusive Features

None

4.3 Impacted Features

None


11/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate 5 Network Impact



5-1

5 Network Impact

5.1 System Capacity

No impact.

5.2 Network Performance

With this feature:

The actual maximum traffic rate of the UE increases if the MBR assigned by the CN is higher than thetypical traffic rates configured at the RNC.

The actual maximum traffic rate of the UE decreases if the MBR assigned by the CN is lower than thetypical traffic rates configured at the RNC.


12/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate 6 Engineering Guidelines



6-1

6 Engineering Guidelines

6.1 When to Use Adaptive Configuration of Typical HSPA Rate

This feature is applicable only to PS best effort (BE) services over High Speed Packet Access (HSPA)channels. This feature enables the RNC to calculate the actual maximum traffic rate based on themaximum bit rate (MBR) assigned by the CN.

6.2 Feature Deployment

This section describes how to activate, verify, and deactivate the optional feature WRFD-030004Adaptive Configuration of Typical HSPA Rate.

6.2.1 Prerequisites

Dependencies on Hardware

The BTS3812E, BTS3812A, and BTS3812AE must be configured with the EBBI, EBOI, EULP+EDLP,or EULPd+EDLP boards. Downlink services must be established on the EBBI, EBOI, or EDLP board.

The DBS3800 must be configured with the EBBC or EBBCd board. Downlink services must beestablished on the EBBC or EBBCd board.

The 3900 series base stations must be configured with the WBBPb, WBBPd, or WBBPf board.Downlink services must be established on the WBBPb, WBBPd, or WBBPf board.

Dependencies on Other Features

The features WRFD-010610 HSDPA Introduction Package and WRFD-010612 HSUPA IntroductionPackage have been configured before this feature is activated.

License

The license "Self-adaption of HSPA Typical Throughput" on the BSC6900 side has been activated. Fordetails about the license items and how to activate the license, seeLicense Management FeatureParameter Description.

6.2.2 Data Preparation

Table 6-1 lists the data to prepare before activating this feature.

Table 6-1 Data to prepare before activating this feature

Parameter Name ParameterID

Setting Notes Data Source

PS Rate

Negotiation Switch

PsSwitch HSPA_ADPTIVE_RATE_ALGO_SWITCH

in the PsSwitch parameter must beselected.

Radio network

plan (internal)

6.2.3 Precautions

None

6.2.4 Activation Procedure

Run the RNC MML command SET UCORRMALGOSWITCH(CME single configuration: UMTS Radio

Global Configuration Express > Connection_Oriented RRM Switch Configuration > Connection Oriented
http://localhost/var/www/apps/conversion/tmp/scratch_2/License%20Management.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/License%20Management.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/License%20Management.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/License%20Management.htmhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/scratch_2/License%20Management.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/License%20Management.htm


13/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate 6 Engineering Guidelines



6-2

Algorithm Switches; CME batch modification center:Modifying RNC Parameters in Batches)to enablethis feature. In this step, select the HSPA_ADPTIVE_RATE_ALGO_SWITCHcheck box under theparameter PS Rate Negotiation Switch.

6.2.5 Verification Procedure1. Before the feature is activated, trigger the CN to assign a non-typical rate for a PS BE service to be

carried on an HSPA channel. Check the real rate.Expected result: The PS BE service is set up successfully on an HSPA channel with a typical rate.

2. After the feature is activated, trigger the CN to assign a non-typical rate for a PS BE service to becarried on an HSPA channel. Check the real rate.Expected result: The PS BE service is set up successfully on an HSPA channel with the assignedrate.

6.2.6 Deactivation Procedure

Run the RNC MML command SET UCORRMALGOSWITCH(CME single configuration: UMTS Radio

Global Configuration Express > Connection_Oriented RRM Switch Configuration > Connection OrientedAlgorithm Switches; CME batch modification center:Modifying RNC Parameters in Batches)to disablethis feature. In this step, clear the HSPA_ADPTIVE_RATE_ALGO_SWITCHcheck box under theparameter PS Rate Negotiation Switch.

6.2.7 Example

//Activating Adaptive Configuration of Typical HSPA Rate

SET UCORRMALGOSWITCH: PsSwitch=HSPA_ADPTIVE_RATE_ALGO_SWITCH-1;

//Deactivating Adaptive Configuration of Typical HSPA Rate

SET UCORRMALGOSWITCH: PsSwitch=HSPA_ADPTIVE_RATE_ALGO_SWITCH-0;
http://localhost/var/www/apps/conversion/tmp/omc/cme/express/rnc-batch.htmlhttp://localhost/var/www/apps/conversion/tmp/omc/cme/express/rnc-batch.htmlhttp://localhost/var/www/apps/conversion/tmp/omc/cme/express/rnc-batch.htmlhttp://localhost/var/www/apps/conversion/tmp/omc/cme/express/rnc-batch.htmlhttp://localhost/var/www/apps/conversion/tmp/omc/cme/express/rnc-batch.htmlhttp://localhost/var/www/apps/conversion/tmp/omc/cme/express/rnc-batch.htmlhttp://localhost/var/www/apps/conversion/tmp/omc/cme/express/rnc-batch.htmlhttp://localhost/var/www/apps/conversion/tmp/omc/cme/express/rnc-batch.html


14/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate 7 Parameters



7-1

7 Parameters

Table 7-1 Parameter description

Parameter ID

NE MMLCommand

FeatureID

FeatureName

Description

PsSwitch

BSC6900

SETUCORRMALGOSWITCH

WRFD-021101

WRFD-010506

WRFD-030004

DynamicChannelConfiguration Control(DCCC)

RABQuality of

ServiceRenegotiation over IuInterface

AdaptiveConfiguration ofTypicalHSPA Rate

Meaning:PS rate negotiation switch group.

1) PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH:When the switch is on, access at a rate of 0 kbit/s or onthe FACH is determined according to the currentconnection state of the RRC if the PS BE admission andthe later preemption and queuing fail.

2) PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH: Whenthe switch is on, the initial rate of the service should bedynamically configured according to the value of Ec/Noreported by the UE when the PS BE service isestablished.

3) PS_BE_IU_QOS_NEG_SWITCH: When the switch ison, the Iu QoS Negotiation function is applied to the PSBE service if Alternative RAB Parameter Values IE ispresent in the RANAP RAB ASSIGNMENT REQUEST orRELOCATION REQUEST message.

4) PS_RAB_DOWNSIZING_SWITCH: When the switch ison and the RAB downsizing license is activated, the initialspeed is determined on the basis of cell resources.Downsizing is implemented for BE services.

5) PS_STREAM_IU_QOS_NEG_SWITCH: When theswitch is on, the Iu QoS Negotiation function is applied tothe PS STREAM service if Alternative RAB ParameterValues IE is present in the RANAP RAB ASSIGNMENTREQUEST or RELOCATION REQUEST message.

6) PS_BE_STRICT_IU_QOS_NEG_SWITCH: When theswitch is on, the strict Iu QoS Negotiation function isapplied to the PS BE service,RNC select Iu max bit ratebased on UE capacity,cell capacity,max bitrate andalternative RAB parameter values in RANAP RABASSIGNMENT REQUEST or RELOCATION REQUESTmessage. When the switch is not on, the loose Iu QoSNegotiation function is applied to the PS BE service,RNCselect Iu max bit rate based on UE capacity,max bitrateand alternative RAB parameter values in RANAP RABASSIGNMENT REQUEST or RELOCATION REQUESTmessage,not consider cell capacity,this can avoid Iu QoSRenegotiation between different cell.The switch is validwhen PS_BE_IU_QOS_NEG_SWITCH is set to ON.

7)HSPA_ADPTIVE_RATE_ALGO_SWITCH (HSPA typical

traffic rate adaptation switch): When this switch is turned
http://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-mml/set-ucorrmalgoswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-mml/set-ucorrmalgoswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-mml/set-ucorrmalgoswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-mml/set-ucorrmalgoswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-mml/set-ucorrmalgoswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-mml/set-ucorrmalgoswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-mml/set-ucorrmalgoswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-mml/set-ucorrmalgoswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-mml/set-ucorrmalgoswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.htmlhttp://localhost/var/www/apps/conversion/tmp/RNCParaHtml/mbsc/m-para/ucorrmalgoswitch_psswitch.html


15/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate 7 Parameters



7-2

Parameter ID

NE MMLCommand

FeatureID

FeatureName

Description

on, the RNC can calculate the actual maximum traffic rate

of PS BE services over HSPA channels based on the MBRassigned by the CN, if the license controlling the AdaptiveConfiguration of Typical HSPA Rate feature is activated.

GUI ValueRange:PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH, PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH,PS_BE_IU_QOS_NEG_SWITCH,PS_RAB_DOWNSIZING_SWITCH,PS_STREAM_IU_QOS_NEG_SWITCH,PS_BE_STRICT_IU_QOS_NEG_SWITCH,HSPA_ADPTIVE_RATE_ALGO_SWITCH

Actual ValueRange:PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH, PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH,PS_BE_IU_QOS_NEG_SWITCH,PS_RAB_DOWNSIZING_SWITCH,PS_STREAM_IU_QOS_NEG_SWITCH,PS_BE_STRICT_IU_QOS_NEG_SWITCH,HSPA_ADPTIVE_RATE_ALGO_SWITCH

Unit:None

DefaultValue:PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH-

0&PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH-0&PS_BE_IU_QOS_NEG_SWITCH-0&PS_RAB_DOWNSIZING_SWITCH-1&PS_STREAM_IU_QOS_NEG_SWITCH-0&PS_BE_STRICT_IU_QOS_NEG_SWITCH-0&HSPA_ADPTIVE_RATE_ALGO_SWITCH-0


16/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate 8 Counters



8-1

8 Counters

There are no specific counters associated with this feature.


17/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate 9 Glossary



9-1

9 Glossary

For the acronyms, abbreviations, terms, and definitions, seeGlossary.
http://localhost/var/www/apps/conversion/tmp/scratch_2/Glossary.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/Glossary.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/Glossary.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/Glossary.htm


18/18

WCDMA RAN

Adaptive Configuration of Typical HSPA Rate 10 Reference Documents



10-1

10 Reference Documents

[1] Radio Bearers Feature Parameter Description

[2] License Management Feature Parameter Description
http://localhost/var/www/apps/conversion/tmp/scratch_2/Radio%20Bearers.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/Radio%20Bearers.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/License%20Management.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/License%20Management.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/License%20Management.htmhttp://localhost/var/www/apps/conversion/tmp/scratch_2/Radio%20Bearers.htm

Adaptive Configuration of Typical HSPA Rate(RAN14.0_03)

Documents

huawei trademarks

copyright huawei technologies

huawei proprietary

huawei industrial basebantian

huawei andthe customer

typical traffic rate

purchase scope

usage scope