INSTRUCCIONES DE USO USER OPERATING INSTRUCTIONS ACUMULADOR DIGITAL INTELIGENTE DIGITAL SMART STORAGE HEATERS ECOMBI PLUS MODELOS / MODELS ECO15 PLUS ECO20 PLUS ECO30 PLUS ECO40 PLUS Por favor, lea estas instrucciones atentamente antes de instalar o utilizar el aparato por primera vez. Please read these instructions carefully before installing or using this appliance for the first time. Youtube Ecombi Plus Puesta en marcha recomendada
36
Embed
ACUMULADOR DIGITAL INTELIGENTE DIGITAL SMART STORAGE ...
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
INSTRUCCIONES DE USO USER OPERATING INSTRUCTIONS
ACUMULADOR DIGITAL INTELIGENTE DIGITAL SMART STORAGE HEATERS
ECOMBI PLUS
MODELOS / MODELS
ECO15 PLUS ECO20 PLUS ECO30 PLUS ECO40 PLUS
Por favor, lea estas instrucciones atentamente antes de instalar o utilizar el aparato por primera vez. Please read these instructions carefully before installing or using this appliance for the first time.
Youtube
Ecombi Plus
Puesta en marcha recomendada
1
1. INSTRUCCIONES IMPORTANTES
Cuando se utilicen aparatos eléctricos se deben seguir siempre unas precauciones básicas para reducir el
riesgo de fuego, electrocución y daños a las personas, incluyendo las siguientes:
• Mantenga materiales combustibles, tales como muebles,
almohadas, ropa de cama, papeles, ropa, cortinas, etc. al
menos a 30cm del frontal, laterales y parte posterior del
equipo. Es esencial que las distancias libres indicadas sean
respetadas.
• PRECAUCIÓN – Algunas partes de este equipo pueden
ponerse muy calientes y causar quemaduras. Se debe prestar
especial atención si están presentes niños o personas con
capacidades físicas, sensoriales o mentales reducidas.
• Este aparato puede ser utilizado por niños mayores de 8 años y por
personas cuyas capacidades físicas, sensoriales o mentales estén
reducidas o carezcan de conocimiento del uso del aparato, sólo si son supervisados o instruidos por una
persona responsable de su seguridad en lo concerniente al uso del aparato de una manera segura y entienden
los riesgos implícitos. Los niños no deben jugar con el aparato. La limpieza y el mantenimiento no debe ser
realizada por niños sin supervisión.
• Niños de más de 3 años y menos de 8 años sólo podrán conectar y desconectar el aparato suponiendo que
ha sido instalado o colocado en su posición normal de operación y que han sido supervisados o instruidos
en el uso del aparato de una manera segura y entienden los riesgos implícitos. Niños de más de 3 años y
menos de 8 años no podrán enchufar, regular ni realizar la limpieza o mantenimiento del aparato.
• Niños de menos de 3 años deben mantenerse alejados a menos de que se les supervise de manera continua.
• No intente reparar el aparato de calefacción si presenta un funcionamiento anormal o fallo. Desconecte el
equipo del cuadro de protección de la vivienda y haga que sea revisado por un electricista cualificado antes
de volver a utilizarlo. Para desconectar el aparato, ponga el interruptor en la posición apagado y desconecte
del cuadro de protección de la vivienda.
• No inserte ni permita que objetos extraños entren a través de las rejillas de ventilación o de salida de aire
ya que esto puede causar una descarga eléctrica o dañar el aparato.
• No utilizar este aparato para secar ropa. Para prevenir incendios no obstruya ninguna entrada o salida de
aire. Las entradas y salida de aire proporcionan un funcionamiento correcto y previenen el
sobrecalentamiento. NO CUBRIR las entradas o salida de aire.
• El aparato tiene en su interior partes calientes y componentes que producen chispas. No utilizar en sitios
donde gasolina, pinturas o vapores o líquidos inflamables se utilicen o almacenen. El uso de estos equipos
está prohibido en locales donde haya gases, explosivos o se manipulen sustancias inflamables. No abrir
nunca el aparato estando esté cargado.
• GUARDE ESTAS INSTRUCCIONES. Este manual debe ser conservado y dado a cualquier nuevo
usuario. Utilice este equipo únicamente como se describe en este manual. Cualquier otro uso no
recomendado por el fabricante puede causar fuego, descarga eléctrica o daño a las personas. La garantía no
cubrirá cualquier daño causado por la no observancia de alguna de estas instrucciones.
• No utilice el aparato en exteriores.
• Ni el cable de conexión ni otros objetos deben estar en contacto con el acumulador.
• Después del montaje, vigilar la primera carga hasta verificar la interrupción de la misma por el control de
carga. Durante este ciclo airear la habitación.
• La presencia en el ambiente de humo de tabaco o partículas en suspensión, polución atmosférica, etc., puede,
oscurecer las superficies de paredes cercanas al acumulador.
• Una puesta en hora incorrecta, una programación errónea de las horas de tarifa reducida, así como consignas
de temperatura demasiado elevadas pueden provocar un elevado coste en la factura de electricidad.
OB
JE
TO
75 mm
CORTINA, MUEBLE O REPISA
min.75 mm
min.
250 mmmin.
2
2.- MODO DE EMPLEO
2.1. Consideraciones Generales
PRECAUCIÓN: NO UTILICE ESTE APARATO PARA SECAR ROPA. No cubra el equipo en ningún momento.
CONECTAR / DESCONECTAR
Interruptor general. Todos los modelos disponen de un interruptor en la parte posterior que
permite la desconexión total del ECOMBI Plus.
TECLADO:
ENCENDIDO / APAGADO
Una vez que el acumulador está conectado al suministro eléctrico, accione el interruptor general situado en la parte posterior
derecha del acumulador a la posición ON para encender el acumulador.
ILUMINACIÓN DISPLAY
Al pulsar cualquier tecla la pantalla se ilumina con un suave color blanco. Al cabo de un tiempo sin pulsar ninguna tecla la
iluminación se apaga.
El teclado sólo responderá cuando la pantalla se encuentra iluminada. Una pulsación de tecla con la pantalla apagada no realiza
ninguna acción sobre el equipo.
BLOQUEO DE TECLADO
En cualquier modo de funcionamiento es posible bloquear el teclado presionando
y simultáneamente durante 3 segundos. Aparecerá el icono cuando el
teclado se haya bloqueado.
Para desbloquear el teclado, pulse y simultáneamente durante 3
segundos.
Nivel de carga actual
Tecla “+”
Pulse esta tecla para aumentar el valor de
diferentes parámetros.
Tecla “-” Pulse esta Tecla para
disminuir el valor de diferentes parámetros.
Tecla “Config / Prog” Pulse la tecla para acceder a la
configuración general del equipo. Pulse esta tecla para salir de los diferentes menús.
Tecla “OK” Pulse la tecla para ver y modificar
la hora. Pulse esta tecla para confirmar valores en los diferentes menús.
Centralita G-Control
Indicador de conexión.
Programación diaria:
Nivel de temperatura para cada tramo horario del día actual.
Bloqueo de teclado
Indicador de modo Programa
Nivel de temperatura actual
en modo PROGRAMA.
Ventanas abiertas
3
2.2. Puesta en marcha (Youtube: Puesta en marcha recomendada ECOMBI Plus)
La puesta en marcha de Ecombi Plus requiere únicamente de 3 acciones básicas:
a. CONFIGURACIÓN HORAS DE CARGA
Selección Tarifa 8 / 14 horas
Ecombi Plus puede funcionar con tarifas de discriminación horaria de 8 o 14 horas de tramo valle. Configure el equipo para 8 o
14 horas según el número de horas valle de su tarifa. Para ello:
- Tarifa 8 horas: Mantenga pulsada la tecla al mismo tiempo que enciende el equipo utilizando el interruptor
general situado en la parte posterior derecha del mismo hasta que se muestre en pantalla el mensaje 8hr.
- Tarifa 14 horas: Mantenga pulsada la tecla al mismo tiempo que enciende el equipo utilizando el interruptor
general situado en la parte posterior derecha del mismo hasta que se muestre en pantalla el mensaje 14hr.
La potencia eléctrica máxima consumida durante el periodo de acumulación varía cuando el equipo está configurado en 8 o en 14
horas.
ECO15 Plus ECO20 Plus ECO30 Plus ECO40 Plus
8 horas 975 W 1300 W 1950 W 2600 W
14 horas 975 W 650 W 1300 W 1300 W
Horas de carga
Las horas de carga del equipo por defecto van de 00:00 a 08:00 para la configuración 8 horas y de 22:00 a 12:00 para la
configuración de 14 horas. En caso de que las horas valle de su tarifa sean diferentes a las mencionadas, puede modificarlas. Para
ello:
- Con la pantalla iluminada, mantenga pulsada la tecla durante 5 segundos para acceder al menú de configuración del
equipo hasta que se muestre la palabra “Func.” parpadeando.
- Pulse la tecla hasta que se muestre la palabra PArA parpadeando.
- Pulse ahora la tecla para acceder al menú de parámetros generales (PArA).
- La palabra UP01 correspondiente al primer parámetro se muestra. El tramo de carga que utiliza el equipo es el
comprendido entre los parámetros UP02(Hora inicio tramo de carga. Por defecto 00:00 en configuración 8 horas y
22:00 en configuración 14 horas) y UP03 (Hora final del tramo de carga. Por defecto 08:00 en configuración 8 horas y
12:00 en configuración 14 horas).
- Utilice las teclas y para posicionarse sobre el parámetro que desea modificar y la tecla para acceder al valor
del parámetro.
- Utilice las teclas y para modificar la hora de inicio / fin del tramo de carga una vez está dentro del parámetro.
Utilice para confirmar su valor.
- Pulse para salir al menú principal cuando haya terminado de realizar las modificaciones deseadas.
UP06: Días de carga en la semana Carga los 7 días de la semana. Carga los 7 días de la semana.
UP07: Corrección temperatura ambiente 0ºC 0ºC
UP08: Tiempo máximo funcionamiento del elemento
de compensación en tarifa con recargo
5 horas 3 horas
UP09: Protección contra sobretemperatura 2ºC 2ºC
UP10: Unidades de temperatura ºC ºC
UP11: Función Ventanas Abiertas Off Off
UP12: Función Puesta en Marcha Adaptable Off Off
UP13: Tipo de Control de Temperatura PID PID
UP14: Restricción compensación en fin de semana On No Aplica
Programa por defecto - Eco 00:00 a 07:00 y 22:00 a 00:00
- Confort 07:00 a 22:00
Una puesta en hora incorrecta, una programación errónea de las horas de tarifa reducida, así como consignas de temperatura
demasiado elevadas pueden provocar un elevado coste en la factura de electricidad.
MODO EMISOR
El equipo dispone de un modo emisor que puede ser activado temporalmente. Para ello, apague el equipo utilizando el
interruptor general situado en la parte posterior derecha del equipo y enciéndalo nuevamente a la vez que mantiene pulsada la
tecla hasta que en la pantalla se muestre el mensaje 19.0E (Indicativo de la activación del modo emisor).
- Este modo es un modo temporal de funcionamiento desde el que no puede acceder al menú de configuración general
del equipo, ni cambiar el modo de funcionamiento, ni permite ninguna otra acción sobre el equipo.
- Utiliza las teclas y para cambiar la consigna de temperatura deseada en este modo de funcionamiento. El equipo
le aportará calor instantáneo mediante la conexión de la resistencia de compensación.
- En este modo de funcionamiento temporal, el equipo nunca cargará.
Para salir del modo emisor y regresar al modo normal de funcionamiento del equipo, simplemente apague y conecte nuevamente
el equipo utilizando el interruptor general situado en la parte posterior derecha.
i
15
3.- FUNCIONAMIENTO CON CENTRALITA G CONTROL HUB Mediante una centralita G-Control Hub conectada a la red del hogar, es posible controlar el funcionamiento completo e integral
del acumulador Ecombi Plus remotamente desde cualquier lugar a través de la app Elnur Wifi Control o a través de la app-web.
(https://remotecontrol.elnur.es). El acumulador Ecombi Plus debe estar asociado a una centralita G-Control Hub conectada a
internet para utilizar esta característica.
Para asociar el Ecombi Plus a la centralita G Control Hub, siga las instrucciones indicadas en la aplicación. Para ello:
- Abra la aplicación e inicie sesión con su usuario y contraseña.
- Acceda al menú de calefacción de la aplicación.
- Pulse el botón instalar (+) situado en la parte de abajo y seleccione el dispositivo correspondiente (Acumulador).
- Presione comenzar búsqueda y siga las instrucciones del asistente.
Cuando se le solicite, pulse el botón del acumulador durante 3 segundos hasta que el símbolo Link se muestre en la pantalla.
Puede ahora controlar y ajustar la programación y temperaturas de consigna del acumulador a través de la app Elnur Wifi
Control o a través de la app-web. (https://remotecontrol.elnur.es).
4.- PROBLEMAS Y SOLUCIONES
El ECOMBI Plus no calienta
Compruebe que el equipo está conectado y en el modo de funcionamiento deseado.
Comprobar que el ECOMBI Plus no esté cubierto o las entradas de aire inferiores obstruidas. Si el
limitador térmico LR ha actuado será necesario rearmarlo manualmente.
El ECOMBI Plus no calienta lo
suficiente
Comprobar que la temperatura seleccionada sea la adecuada. Es posible que la habitación necesite
más potencia de calefacción.
El display muestra mensajes de
error Por favor, contacte con el Servicio de Asistencia Técnica.
El teclado no responde
Si el display muestra el símbolo , el teclado del ECOMBI Plus se encuentra bloqueado. Mantenga
pulsadas las teclas “+” y “-” durante unos segundos para desbloquearlo. (Vea la sección “Bloqueo
de Teclado”).
Si el display muestra el símbolo parpadeando, el teclado ha sido bloqueado remotamente y sólo
es posible desbloquearlo utilizando la aplicación.
Ecombi Plus no comunica
con la centralita G-Control
Hub.
Asegúrese de que el equipo está asociado, el icono debe aparecer fijo en el
display.
Para distancias mayores de 30 metros y 2-3 paredes, asocie primero los equipos más
cercanos, ya que cada equipo puede ejercer de repetidor.
Si el icono parpadea, revise que la centralita está correctamente conectada, o si
se ha eliminado algún equipo que pudiera estar ejerciendo de repetidor.
A potencia calorífica nominal elmax 0.000 0.000 0.000 0.000 kW
A potencia calorífica mínima elmin 0.000 0.000 0.000 0.000 kW
En modo de espera elSB <0.0005 <0.0005 <0.0005 <0.0005 kW
Información Valor. Todos
los modelos
Tipo de aportación de calor
Control electrónico de la carga de calor con respuesta a la temperatura interior o exterior Sí
Tipo de control de potencia calorífica / de temperatura interior
Control electrónico de temperatura interior y temporizador semanal Sí
Otras opciones de control
Control de temperatura interior con detección de ventanas abiertas Sí
Con opción de control a distancia Sí
Con control de puesta en marcha adaptable Sí
Información de
contacto
ELNUR, S.A.
Travesía de Villa Esther, 11
28110 – Algete (Madrid), España
Reglamento (UE) 2015/1188 de la comisión de 28 de abril 2015. Requisitos de diseño ecológico aplicables a los
aparatos de calefacción local eléctrico de acumulación.
ES: ADVERTENCIA: Para evitar sobrecalentamientos, no cubrir el aparato de calefacción.
ES
El símbolo en el producto o en su embalaje indica que este producto no se puede tratar como desperdicios normales del hogar. Este producto se debe entregar al punto de recolección de equipos eléctricos y electrónicos para reciclaje. Al asegurarse de que este producto se deseche correctamente usted ayudará a evitar posibles consecuencias negativas para el ambiente y la salud pública, lo cual podría ocurrir si este producto no se manipula de forma adecuada. Para obtener información más detallada sobre el reciclaje de este producto, póngase en contacto con la administración de su ciudad, con su servicio de desechos del hogar o con la tienda donde compró el producto. Estas disposiciones solamente son válidas en los países miembros de la UE.
18
1. –IMPORTANT INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the following:
• Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes,
etc. and curtains at least a foot (30cm) from
the front, sides and rear of the heater. It is
essential that the indicated minimum
clearances are maintained.
• CAUTION — Some parts of this product can become
very hot and cause burns. Particular attention must be
given where children and vulnerable people are
present.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children must not play with the appliance. Cleaning and user maintenance must not be made by children without
supervision.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has
been placed or installed in its intended normal operating position and they have been given supervision or
instruction concerning use of the appliance in a safe way and understand the hazards involved. Children
aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user
maintenance.
• Children of less than 3 years should be kept away unless continuously supervised.
• Do not operate any heater after it malfunctions. Disconnect power at service panel and have heater
inspected by a reputable electrician before reusing. To disconnect heater, turn controls to off, and turn off
power to heater circuit at main disconnect panel.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
electric shock or fire or damage the heater.
• Do not use this heater to dry clothes. To prevent a possible fire, do not block air intakes or exhaust in any
manner. Air inlets and outlets provide proper operation of the appliance and prevent its overheating. DO
NOT cover air inlet and outlet grills.
• A heater has hot and arcing or sparking parts inside. Do not use in areas where gasoline, paint, or
flammable vapors or liquids are used or stored. The use of these heaters is forbidden in any area where
there is a presence of gases, explosives or inflammable objects. Never open a charged heater.
• SAVE THESE INSTRUCTIONS. This guide must be kept and given to any new user. Use this heater
only as described in this manual. Any other use not recommended by the manufacturer may cause fire,
electric shock, or injury to persons. The warranty of the heater will not cover any damage caused by non
observance of any of these instructions.
• Do not use this heater outdoors.
• Neither the connecting cable nor any other object must come into contact with the hot unit.
• After installation a survey of the first charging cycle should be carried out to ensure that the main input
thermostat switches off. Ventilate the room during this first cycle.
• The presence of air particles of smoke, dust and other pollutants could, in time, discolor the walls and
surfaces around the heater.
• Incorrect time settings, erroneous programming of the reduced rate time and too high temperature
settings may result in a high cost of your electricity bill.
19
2. - OPERATING INSTRUCTIONS
2.1. General information
CAUTION: DO NOT USE THIS HEATER TO DRY CLOTHES. Do not cover this heater at any time.
CONNECTION / DISCONNECTION
Power switch. All models are equipped with a switch on the back
side panel. It is used to connect and disconnect ECOMBI PLUS.
KEYBOARD:
ON/OFF
Once the heater is connected to a main supply you can turn the heater ON by switching the main ON/OFF switch positioned at
the rear right side of the heater as shown above.
BACKLIGHT
Pressing any button, the display will illuminate with a soft white colour. After certain time if no buttons are pressed the display
backlight will turn off.
Buttons only will respond when the backlight is on.
KEYBOARD LOCK
During any operation mode, it is possible to lock the keyboard by holding
and simultaneously for 3 seconds. When the keyboard is locked, the
indicator will be displayed.
To unlock the keyboard, press and simultaneously for 3 seconds.
Current charge level
Button “+”
Press the key to increase
different values. Button “-” Press the key to decrease
different values.
“Config / Prog” Button Press the button to access the
advanced configuration. Press this button to exit from the different menus.
“OK” Button Press the button to check and set the time.
Press the button to confirm values in the different menus.
G-Control Hub connection indicator.
Key lock indicator
Daily Programming: Temperature level for each
time interval (1h) of the day.
Open Windows detection indicator
Programme mode indicator
Current set point in Programme Mode
20
2.2. Quick Start
Ecombi Plus quick start only requires 2 easy settings:
TIME AND CHARGE SETTING
Charging Hours: By default, Ecombi Plus off-peak period is set from 00:00 to 08:00. In case off-peak period of your electricity
tariff does not match with this setting, you can easily modify it:
- With backlight on, keep pressed button for 5 seconds until the message “Func.” is displayed blinking to access the
general configuration menu.
- Press button until the text “PArA” is displayed blinking.
- Press now button to access general parameteres menu (PArA).
- Parameter UP01 is displayed. Charging period used by Ecombi Plus goes from UP02 parameter (Charging period start.
By default 00:00) to UP03 parameter (Charging period end. By default 08:00).
- Use and buttons to move forward and backward until the parameter to be modified is displayed. Press
button to access the parameter value.
- Use and buttons to modify the time of the start / end of the charging period. Use button to confirm the
desired value.
- Press to exit main menu.
Time setting: Ecombi Plus time setting is set on factory by default. Check the time setting in your device. In case time setting is
wrong, you can easily modify it following next steps.
OPERATION MODE SETTING & TEMPERATURE SET POINT
1. With backlight on, keep pressed button for 5 seconds until the message “Func.” is displayed blinking to access the
general configuration menu.
2. Press button when the message “Func.” is displayed to access operation mode menu.
3. Press or buttons to select basic (24 hours Set-Point Temperature) operation mode. Press button to confirm.
Current charge level and set-point temperature are displayed in this mode.
4. Once selected, adjust the desired set-point temperature using and . Automatically, Ecombi Plus will manage and adjust
daily its charging level to provide the selected temperature with minimal cost.
21
2.3. Advanced Configuration
General configuration menu allows you to make additional changes and adjustments for the commissioning and operation of the
equipment.
To enter the general configuration menu, keep pressed button for 5 seconds in any operation mode with the backlight on.
Next information is displayed:
Use and buttons to navigate for the different available menus and press button to enter the configuration menu you
want to modify.
From general configuration menu, you can enter 5 different menus that allow to set any configuration of your device:
- Working operation mode. Modify the working operation mode.
- Time setting menu. Set the time and day of the week in your device.
- Temperatures. Programme mode. Modify the temperature value for the temperature levels used in programme
mode. (Sun, Moon and Frost protection temperatures)
- Weekly temperature programming. Programme mode. Modify the weekly temperature programming of the
programme mode.
- General parameters. Modify the general working parameters of the device (Temperature units, charging period…).
22
2.3.1. Working operation mode
The heater has three different operation modes: Programme, Basic (Temperature 24 hours) and Frost Protection.
- Basic Mode (Temperature 24 hours): the storage heater will maintain the temperature set point 7 days a week, 24
hours a day. In this mode, the device adjusts automatically its daily charging level to maintain the selected temperature set-
point. To modify the set-point temperature, just press or buttons when the device is working in this mode until
the desired temperature is shown. Set-point temperature and charging level are displayed in this operation mode.
- Programme Mode: The setpoint temperature varies according to the weekly schedule setup in the unit. 3 different
temperature levels (Comfort, Moon and Frost Protection) can be selected for each time interval (1 hour) to adjust the
temperature in the room to the habits and needs of the different users. Set temperature levels can be modified (See 2.3.3
Temperature levels. Programme mode) In addition, weekly temperatures programme can be modified (See 2.3.4.
Weekly programming. Programme mode). PRG icon, horizontal temperatures diagram at the top of the display, current
temperature level and charging level and displayed in this mode.
- Frost Protection: the storage heater doesn't maintain any set temperature or run any programs, keeping the time
settings configured previously. Balancing heating element will be turned on in case the ambient temperatures drops below
the Frost Protection temperature level. Current time and frost protection symbol ( ) are displayed in this mode.
During any operation mode, access the general configuration menu as stated in the general configuration section (Section 2.3)
and press button when the text “Func.” is displayed to access the working operation mode menu. Use or to select
the desired working operation mode. Confirm with .
23
2.3.2. Time setting
To check the time setting, press with the backlight on in any operation mode. The time and day of the week set in the unit are
displayed.
If time setting is wrong, keep pressed button for 5 seconds when the time and day of the week is displayed to modify it.
- Hours start blinking first. Use and buttons to set the hour. Press to confirm.
- Minutes start blinking. Use and button to set the minutes and confirm with .
- Lastly, day of the week start blinking at the top of the display in numeric format (1=Monday, 2=Tuesday, etc). Use and
buttons to set the day of the week and confirm with .
button can be pressed at any time to exit the setting time menu.
It is possible to access the time setting menu from the general settings menu (Section 2.3).
If the device is associated with a G-Control Hub, the adjustment of time is removed and the time in the G-Control Hub is configured in
the heater automatically.
ECOMBI PLUS does not change automatically from summer time to winter time or vice versa when not connected to the internet.
Depending on the tariff it may be necessary to change the clock settings to fit these two timings.
i
i
24
2.3.3. Temperatures. Programme Mode
Temperature level set-points used in programme mode (Comfort, Economic and Frost Protection) can be modified at any time.
During any operation mode, access the general configuration menu as stated in the general configuration section (Section 2.3)
and press button when the 3 temperature icons (sun, moon and frost protection) and the symbol ºC are displayed to access
the temperatures level menu.
Now press to select the temperature you want to change, COMFORT or ECONOMIC. Use and to select the desired
temperature.
button can be pressed at any time to exit the setting time menu.
You can temporary change the set temperature for the current time period too in programme mode. To do this, increase or
decrease the current temperature simply by pressing and . Once the time period finishes, the temperature will revert back
to the programmed set temperature
25
2.3.4. Weekly temperature programming. Programme Mode
WEEKLY PROGRAMMING
Default weekly temperature programme can be modified, setting for each hour of the week the desired temperature level
(Comfort, Economic or Frost Protection).
During any operation mode, access the general configuration menu as stated in the general configuration section (Section 2.3)
and press button when the symbol PRG and the horizontal temperatures diagram is displayed.
The first segment of the first day of the week (Day 1- Monday; Time 00:00) will start to flash. The bar diagram at the top of the
display represents the programme for every hour of the day you are programming.
- 2 bars represent this hour is programmed with comfort temperature level. ( )
- 1 bar represents this hour is programmed with economic temperature level. ( )
- No bar represents this hour is programmed with frost protection temperature level. ( )
By pressing , you can select whether you want a Frost Protection setting (3°C), Moon setting (18°C) or Comfort setting
(21°C) for this hour.
Now press to move to the next 1hour time interval. The selected temperature level is set in the new 1-hour time interval.
Once you've gone through all the time intervals for day 1, you will automatically start on day 2 by pressing . Repeat the above
steps until you go through all 7 days.
PROGRAMMING COPY, MOVE FORWARD TO THE NEXT DAY WITHOUT PROGRAMMING
- If you do not desire to modify the programming of a day within the week, press to go through the next day.
- You can copy the programming of the current day from current day to the rest of days in the week.
o Keep pressed button to copy the programming of the current day in the next one in the week. Message
CPXY will be displayed confirming the copy where X: Current day; Y:Next day in the week.
o Keep pressed button to copy the programming of the current day in the rest of days in the week. Message
CPAll will be displayed confirming the programming of the current day has been satisfactory copied in the rest of
the days in the week.
Ecombi Plus will not charge in Frost Protection time intervals . It is recommended to use this temperature level only for complete
days where no heat is required.
i
26
PROGRAMMING EXAMPLE
SET UP DAY 1 PROGRAMME (Monday)
Step by Step Guide
Copy Programme from Day 1 to Day 2
Copy Programme from Current Day to All Days
27
2.3.5. General parameters Access to parameter menu
Access to the parameter value
Change value: Decrease
Confirm value
It is possible to modify the general operation parameters at any moment such
as charging configuration, temperatures units…
During any operation mode, access the general configuration menu as stated in
the general configuration section (Section 2.3) and press button when
the text “PArA.” is displayed to access the general parameters menu.
UP01 will be displayed.
Use and to move on through the different parameters.
Use to access the parameter you want to modify. Change the value using
the navigation keys and . Confirm the new value with .
It is possible to save the changes and exit at any moment by pressing .
Ecombi Plus general parameters that can be modified by the user are.
- UP01: Initial % of storage charge.
- UP02: Starting time of reduced (off-peak) rate electric period.
- UP03: Ending time of reduced rate electric period.
- UP04: Starting time of the second reduced rate electric period. (if not
available set up 00:00).
- UP05: Ending time of the second reduced rate electric period. (if not
available set up 00:00).
- UP06: Charging days during the week.
- UP07: Temperature ambient sensor correction (values from -5ºC to
5ºC).
- UP08: Maximum working period of the balancing heating element in on
peak electric period. Set up this value to “0” to cancel the balancing
heating element operation in on peak electric periods. With balancing
heating operation cancelled, the charge correction will not operate and
the same charging level will be applied every day. (Default 5 hours)
- UP09: Excess of temperature protection during the charge, Degrees
higher than the comfort set point temperature (Programme Mode) or
the set point temperature (Basic Mode) when the charge is interrupted.
(Values 1,2,3,4 & 5).
- UP10: Degrees Celsius or Fahrenheit. (Values: ºC – F).
- UP11: Open Window Detection Activation. (On/Off).
- UP12: Adaptive Start Control Activation (On/Off).
- UP13: Kind of temperature control. Recommended & default PID.
- UP14: Weekend Balancing Element restriction. The maximum working
hours for the balancing element set in UP08 can be disabled for
weekends by setting Off this parameter. (By default: On)
ECOMBI PLUS does not change automatically from summer time to winter
time or vice versa when not connected to the internet. Depending on the tariff it may
be necessary to change the clock settings to fit these two timings
i
28
2.3.5.1. Charging configuration. Weekly charge period setting Weekly charging days (UP06 parameter)
Charging/Not Charging day 1
Advance to the next day
Access to the general parameters menu to modify the charging period of your
Ecombi Plus storage heater. (See “2.3.5.General Parameters”). By default,
00:00 to 08:00 charge period is set and every day of the week is set as a
charging day.
Charge period
Two charging periods can be selected in the electronic control of your Ecombi
Plus.
- 1º Charging period: UP02 to UP03. (00:00 to 08:00 by default).
- 2º Charging period: UP04 to UP05. (Disabled by default, 00:00 to 00:00).
Weekly charging days
It is possible to select which days Ecombi Plus will charge and which days it
will not. Access to the UP06 parameter to modify the days you want your
Ecombi Plus takes a charge. (By default, 7 days of the week).
Access to UP06 parameter by pressing . The first day indicator in the top
of the display and the charge condition (On/Off) is displayed.
Press and to change the charge condition for this day. Press to go
on through the days.
Ecombi Plus will not charge in Frost Protection time intervals. When setting a
day as “No charging day”, Ecombi Plus will automatically set Frost Protection
Temperature in all time intervals of this day in Programme Mode. In addition, Frost
Protection Temperature will be set for this day in Basic Mode, setting the previous
set temperature for Basic Mode when the “no charging day” ends.
i
29
SMART STORAGE HEATER:
Ecombi Plus optimizes the energy management and consumption and provides the heat demand requested by the user in each
period of time reaching the desired comfort.
Smart charging control
Ecombi Plus allows optimizing the energy management and consumption using a linear regression model based on the
temperature registered in the core of Ecombi Plus to determine the current % of the storage heater charge and use this
information to charge only the heat necessary to supply the daily heat demand and avoid unnecessary energy consumption.
The charge level is monitored every time by the electronic control and represented in the display by the dots at the bottom of
the display. 5 dots represent a fully storage heater charge.
While Ecombi Plus is charging, the last dot is flashing at the top right part of the display.
Protection for excess of temperature in the room
In order to achieve maximum savings and avoid unnecessary energy consumption, if, during the charging period, the temperature
in the room exceeds the temperature set up in Ecombi Plus for that room, then the charging will be interrupted until the
temperature in the room decreases.
Charge correction
The % of the storage heater charge is corrected automatically by Ecombi Plus software. If working hours of balancing element is
higher than a certain value, storage heater charge will be increased by a certain %. On the other hand, if balancing element
working hours does not exceed this value, storage heater charge level is reduced by the same %.
This behaviour adapts the consumption to the real thermal needs, allowing the maximum level of energy savings at the required
comfort. The set-up temperature is independent of the Storage Heater level of charge. Initial setting for charge is 100%. This
value can be modified by entering “General Settings” part and modify the initial % of storage charge according to UP01 setting.
Balancing Heating Element
If the energy discharged with natural convection is not enough to satisfy the heat demand of the room where Ecombi Plus is
installed, a balancing heating element incorporated in the Ecombi Plus body will be connected providing additional heating to the
room if necessary to supply the heat demand of the room. The maximum working period of the balancing heating element
during on-peak electric electric periods can be adjusted and cancelled by modifying UP08 parameter. (please go to “2.3.5.
General Parameters”).
Storage Heater and Balancing Heating Element will never work at the same time.
Open Window Detection
With open window detection activated, the balancing element operation will be disconnected automatically when a sharp
decrease in temperature in the room is detected avoiding energy wastage.
When Open Windows Detection function is working, the icon is displayed.
Adaptive Start Control
With adaptive start control activated, Ecombi Plus electronic control analyses the heating requirements of the room where it is
installed using this information to turn on the balancing heating element in advance in order to reach the set point temperature
at the desired time.
When Adaptive Start Control function is working, the icon is displayed.
i
i
i
i
Current Charge Level
Balancing Element ON
30
DEFAULT SETTINGS & RESET
To reset the unit to factory default settings, press and simultaneously for 5 seconds until the message SrES is displayed.
Confirm the reset with .
Default Values
Sun: Comfort temperature 21ºC
Moon: Economic temperature 18ºC
Frost protection temperature 3ºC
UP01: Initial % of storage charge 100%
UP02: Starting time off peak period 1 00:00
UP03: Ending time off peak period 1 08:00
UP04: Starting time off peak period 2 00:00
UP05: Ending time off peak period 2 00:00
UP06: Charging days of the week Default -> Charging 7 days of the week.
UP07: Ambient sensor Offset 0ºC
UP08: Max. Balancing element – working period 5 hours
UP09: Overtemperature protection 2ºC
UP10: Temperature Unit ºC
UP11: Open Window Detection Function Off
UP12: Adaptive Start Control Off
UP13: Kind of temperature control PID
UP14: Weekend Balancing Element restriction On
Default Programming Comfort: 07:00 to 22:00.
Eco: 00:00 to 07:00 & 22:00 to 00:00.
Incorrect time settings, erroneous programming of the reduced rate time and too high temperature settings may result in a high cost
of your electricity bill.
EMITTER MODE
This operation mode is used when it is necessary to heat the room temporarily and there is no need for storage heating.
To set this mode, turn off the unit by pressing the main switch on the back-side panel and keep pressed for 10 seconds at
the same time you turn on the unit by pressing the main switch until the message 19.0E is displayed on the display.
- Emitter mode is a temporary operation mode. You cannot access from this mode to general setting menu, operation
mode menu or any other settings.
- Use and to modify the set-point temperature for this operation mode. The unit will turn on the balancing
heating element if required in order to provide instantaneus heat to the room.
- The unit will not charge within this mode.
To exit emitter mode and go back to the commom operation mode, just turn off and turn on the unit again by pressing the main
switch on the back-side panel.
i
31
3.- REMOTE OPERATION USING THE WIFI G-CONTROL HUB
It is possible to control the full operation of the unit remotely with the Elnur Wifi Control app or the app-web
(https://remotecontrol.elnur.es). The unit must be connected to a Wifi G-Control Hub connected to the internet to use this
feature.
To associate the Ecombi Plus unit to the G-Control Hub, follow the instructions of the installation wizard of the app.
- Open the application and login with your user and password.
- Access the heating menu in the app.
- Press the button Add (+) and select the type of heater that you are going to connect (Storage heater).
- Press Start Search and follow the instructions of the installation wizard.
When required, keep pressed on the storage heater for 3 seconds until the Link symbol is displayed in the storage
heater display.
You can now control and adjust the programming and temperatures on the Ecombi Plus via the Elnur Wifi Control app or the
app-web (https://remotecontrol.elnur.es).
4.- TROUBLESHOOTING
ECOMBI PLUS does not heat.
Please check it is connected and switched on.
Make sure the device is not covered or the lower air inlets are not obstructed. The LR safety limit
may be activated; in this case it is necessary to reset it manually. Please contact technician.
ECOMBI PLUS does not reach
set up temperature
Make sure that adequate temperature is selected.
Make sure the storage heater is sized correctly for heat loss.
“Err” Message in display Please contact technician.
Keyboard does not respond
If the symbol is displayed, the keyboard is locked. Hold “+” and “-” buttons simultaneously for 3
seconds to unlock the keyboard. (See Keyboard Lock Section).
If the symbol is displayed blinking, the keyboard has been locked remotely. Use the app to unlock
the keyboard.
ECOMBI PLUS does not
communicate with the G
Control Hub.
Check the unit is associated, the symbol must be shown on the display LCD.
For distances greater than 30 metros and 2-3 walls, associate first the closest units. Each unit can
work as signal extender.
If symbol is flashing, check the G Control Hub connexion to the network, and if any other
device in the RF Net that could be working as signal extender has been removed.
At nominal heat output elmax 0.000 0.000 0.000 0.000 kW
At minimum heat output elmin 0.000 0.000 0.000 0.000 kW
In standby mode elSB <0.0005 <0.0005 <0.0005 <0.0005 kW
Item Value. All
models
Type of heat input
Electronic heat charge control with room and/or outdoor temperature feedback Yes
Type of heat output / room temperature control
Electronic room temperature control plus week timer Yes
Other control options
Room temperature control, with open window detection Yes
With distance control option Yes
With adaptive start control Yes
Contact details
ELNUR, S.A.
Travesía de Villa Esther, 11
28110 – Algete (Madrid), Spain
Commission Regulation (UE) 2015/1188 of 28 April 2015. Ecodesign requirements for electric storage local space
heaters.
EN: WARNING: In order to avoid overheating do not cover the heater.
EN
The symbol on the product or in its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. These instructions are only valid in the EU member states.
34
Notas de uso / User Notes
Como parte de la política de mejora continua, Elnur, s.a. se reserva el derecho a realizar modificaciones técnicas sin previo aviso. As a part of the policy of continuous product improvement Elnur UK Ltd. reserves the right to alter specifications without notice.
ELNUR S.A. Travesía de Villa Esther, 11 28110 Algete - Madrid Tfno. Atención al Cliente: +34 91 628 1440