TORX PLUS ® Drive The TORX PLUS ® Drive was designed to enhance assembly line performance. Manufacturers all over the world have realized significant improvements and cost savings by switching to the TORX PLUS ® Drive. TORX PLUS ® Drive Solutions The straight, vertical sidewalls of the TORX PLUS ® Drive System virtually eliminate camout. Also, the TORX PLUS ® recess completely encloses the driver tip, reducing tool slippage as well as costly and unsightly damage to the fastener and surrounding surfaces. The elliptically-based geometric configuration of the TORX PLUS ® Drive System maximizes engagement between driver and fastener. It spreads driving forces over the surface area, extending tool life. TORX PLUS ® Drive is the only drive system designed to ensure optimum torque transmission and, ultimately, required clamp load. With a true 0° drive angle , the TORX PLUS ® system virtually eliminates the radial forces that can cause stress on fastener recesses. Ergonomic studies demonstrate that the TORX PLUS ® Drive System can reduce fatigue and muscular stress during the manual assembly of fasteners. That’s because little or no end load is required to keep the driver engaged in the recess. AUTOSERT ® Feature The AUTOSERT ® Feature is the high productivity answer to high rpm engagement on the assembly line. The patented feature is a TORX PLUS ® Drive exclusive. Compound angle guide ramps, used at each lobe, allow for higher rpm engagement. It’s the perfect solution for automated, robotic and other assembly situations where the driver bit is continuously rotating. The AUTOSERT ® feature even helps in manual assembly, creating a self-centering and engaging action. www.acument-global.com Aerospace/Defence Asia Pacific Contact details Copyright All text, graphics and the selection and arrangement thereof, are the property of Acument Intellectual Properties, LLC and are ©2007 Acument Intellectual Properties, LLC. Allrights reserved. Trademarks: ACU ® , ACUMENT ® , ACUPOINT ® , AGGRE-GATOR ® , AUTOSERT ® , BI-FLEX ® , CAMCAR ® , CAMGRIP ® , CAMTAINERS ® , CAMTRONIC ® , CONFLEX ® , CREST CUP ® , DRIL-FLEX ® , DRILIT ® , ELCO ® , FAB-LOK ® , FLEX TECHNOLOGY ® ,FLO-SEAL ® , HANGERMATE ® , MAG-FORM ® , MICROTECH ® , NACRO ™ , OPTIA ® , Our technology. Your success ® , PANELMATE ® , PUSHTITE ® , SPEED FASTENING ® , STALGARD ® , STRUX ® , TORX ® , TORX PLUS ® , ULTRACON ® , and VENT-ALL ® are trademarks or registered trademarks of Acument Intellectual Properties, LLC in the United States or other countries. AVBOLT ® , AVDEL ® , AVDELOK ® , AVEX ® , HEMLOK ® , MAXLOK ® , and MONOBOLT ® are registered trademarks of Avdel UK Limited in the United Kingdom or other countries. Delta-PT ® , Duro-PT ® and PT ® are registered trademarks of EJOT Verbindungstechnik GmbH & Co, KG. FASTITE ® , PLASTITE ® , REMFORM ® , TAPTITE ® , and TAPTITE 2000 ® are trademarks licensed by Research Engineering & Manufacturing Inc. DACROMET ® is the registered trademark of Metal Coatings International Inc. PHILLIPS ® is the registered trademark of Phillips Screw Company. MAThread ® is the registered trademark of MAThread Inc. M-CUT ® is the registered trademark of M-Cut Systems GmbH & Co. KG GMBH & CO. NYLOK ® is the registered trademark of Nylok Corporation. MicroTorque ™ is the trademark of Dynaroll Corporation. Colin Campbell Asia Pacific Sales & Field Application Manager Aerospace/Defence t: (+61 3) 976 6426 ; (+61 403) 388 692 e: [email protected] Phua Cheng Siong Asia Pacific Technology Director t: (+65) 6372 5647 e: [email protected] Lim Say Yan Singapore & Malaysia Sales Representative t: (+65) 9691 6151 e: [email protected]