Accessories - QCD Ltd

96

Accessories

QCD Limited, 28 Hargreaves Street, Ponsonby, Auckland 1011, New Zealand | PO Box 47760, Ponsonby, Auckland 1144, New Zealand Phone: +64 9 366 7118 | Freephone: 0800 240 040 | Fax: +64 9 366 7119 | E-mail: [email protected]

Rin

gs

& G

rom

met

s

Inox Pressed Ring System SETTING INOX RINGS

• The design build-up will allow the maximum strength of the ring to be developed. In lighter sails, it is not imperative to use this design thickness.

• Inox Rings should always be set on the correct tools.

• Damage to the dies can be caused by excessive pressure. Always start with the pressure valve unloaded and build up from zero to the desired pressure.

• Tools should be polished if wear becomes evident. Light lubrication of the working faces is recommended.

• Rings must be closed with the pinned section and liner facing up in the base of the closing tool.

• Surrounding cloth should be supported while ring is being closed.

Part No.

Cloth Build-Up Thickness

(mm)

Hole Punch Size

(mm/in)

Hole Punch

Part No.

Closing Tool Part

No.

Suggested Closing Force

Tonnes

Hole Size when set (mm/in)

HD208 0.7 12.7 / 1⁄2 C155 C408 6 - 9 10 / 3/8

HD207 0.6 15.9 / 5/8 C156 C407 6 - 8 12 / 1⁄2

HD209 1.6 19.0 / 3⁄4 C157 C409 9 - 11 15 / 5/8

HD210 2.1 22.2 / 7/8 C158 C410 11 - 15 20 / 7/8

HD211 2.5 28.6 / 1 1/8 C160 C411 13 - 16 25 / 1

HD212 2.8 34.9 / 1 3/8 C162 C412 18 - 20 30 / 1 1⁄4

HD213 3.1 38.1 / 1 1⁄2 C163 C413 19 - 23 35 / 1 3/8

HD214 3.3 44.5 / 1 3⁄4 C164 C414 20 - 25 40 / 1 5/8

OUTHAUL SLUG SLIDE ATTACHMENTS

• Type 316 stainless steel strap provides ultra-high strength attachment to Inox rings.

• Minimum offset permits ring to be very low in the sail.

• Low friction injection molded slide with encapsulated bail.

Part No. To be used with Diameter (mm/in) Pack Qty

HB2076 D207 9.3 / 3/8 25

HB2095 D209 7.9 / 5/16 25

HB2096 D209 9.3 / 3/8 25

HB2106 D210 9.3 / 3/8 25

HB2108 D210 12.0 / 1⁄2 25

TEFLON® LUBRICATING SPRAY

• Use for lubricating dies, closing tools and generally around the loft.

• Synthetic lubricant that out-performs and outlasts petroleum based lubricants.

• Reduces friction and wear.

• Prevents rust and corrosion.

• Contains no CFC’s or chlorinated solvents.

Part No. Liquid measure

M005 312ml/11 Fl oz

INOX PRESSED RINGS

The Bainbridge International Inox Ring System has been in constant worldwide use by top sailmakers for many years because it offers high strength and corrosion resistance with ease of setting and a range of attachments to simplify and enhance sail attachment points.

• Manufactured from type 316 stainless steel, and injection molded nylon.

• Liners and pins are passivated to reduce risk of staining.

• Liners are seamless for maximum strength.

• Range of colors to permit the use of house colors and sail identification.

• Finely pointed pins penetrate between the sailcloth fibers and do not cut the fabric.

• Nylon ring gives chafe-free contact with sailcloth.

• When set, the pins are locked through the sailcloth and into the opposite face of the ring providing DOUBLE SHEAR strength.

• Excellent internal profile for attachment of sheets. Often used as Cunningham.

Part No. Set Hole Dia (mm/in) Colour Pack Qty

HD208B 10 / 3/8 Black 50

HD207B 12 / 1⁄2 Black 50

HD209B 15 / 5/8 Black 50

HD209N 15 / 5/8 Blue 50

HD210B 20 / 7/8 Black 50

HD210N 20 / 7/8 Blue 50

HD211B 25 / 1 Black 50

HD211N 25 / 1 Blue 50

HD212B 30 / 1 1⁄4 Black 25

HD213B 35 / 1 3/8 Black 25

HD214B 40 / 1 5/8 Black 10

INOX RINGS FOR HAND CLOSING

• Nickel Plated Brass Liners replace the regular stainless steel liners to permit closing without the use of a hydraulic press.

• These rings can be closed by using the tools shown opposite.

Part No. Set Hole Dia (mm/in) Colour Pack Qty

HD207BH 12 / 1⁄2 Black 50

HD209BH 15 / 5/8 Black 50

HD209NH 15 / 5/8 Blue 50

Completely and correctly closed Inox. Ring

!Special Shipping

97

Accessories


Hand Sew Rings & Spinnaker Hardware CLOSING TOOLS FOR INOX RINGS

• These tools are suitable for most presses. All except C408 can be used with Enerpac-Nautilus pull down presses by pushing out the center post.

Part No. Use tool for

C408 D208

C407 D207

C409 D209

C410 D210

C411 D211

C412 D212

C413 D213

C414 D214

ENERPAC/NAUTILUS II SCREW POST & PLUG

• Made from high tensile steel.

• Never use more than the prescribed pressure.

Part No. To be used with Bolt Length (mm/in) Bolt Size (mm/in)

C416SP C407E, C409E 100 / 4 11 / 7/16

C423SP C423E 130 / 5 15 / 5/8

C430SP C430E 130 / 5 20 / 3⁄4

C438SP C438E-C460E 130 / 5 25 / 1

C416P C407E, C409E 11 / 7/16

C423P C423E 15 / 5/8

C430P C430E 20 / 3⁄4

C438P C438E-C460E 25 / 1

SPINNAKER SWIVELS - BRONZE

• Heavy duty fitting with ball bearing swivel.

• Reduces spinnaker twisting during hoist, thus eliminating the possibility of hour glassing.

• B530 allows quick attachment to the spinnaker without the need for webbing or hand sewing.

Part No. Size Max Load (kg/lb) Length (mm/in)

B521 0 700 / 1500 47 / 1 7/8

B530 700 / 1500 70 / 2 3⁄4

BRASS RINGS

• Manufactured from heavy solid brass.

Part No.Inside Width

(mm/in)Thickness (mm/in)

Use with Liner No.

Pack Qty

Q143 12 / 1⁄2 3 / 1/8 Q243 - 3 100

Q144 15 / 5/8 4 / 5/32 Q244 - 4 100

Q145 19 / 3⁄4 5 / 3/16 Q245 - 5 100

Q146 22 / 7/8 5 / 3/16 Q246 - 6 50

Q147 25 / 1 5 / 3/16 Q247 - 7 50

Q148 28 / 1 1/8 5 / 3/16 Q248 - 8 50

Q149 31 / 1 1⁄4 6 / 1⁄4 Q249 - 9 50

Q150 38 / 1 1⁄2 8 / 5/16 Q250 - 10 20

BRASS EYELET GROMMETS/LINERS

Part No.Outside Diameter

(mm/in)Use with Liner No. Pack Qty

Q244 15 / 5/8 Q144 - 4 100

Q247 25 / 1 Q147 - 7 50

Q248 28 / 1 1/8 Q148 - 8 50

Q250 38 / 1 1⁄2 Q150 - 10 20

SPINNAKER BAG HOOPS

• Stainless steel TIG welded hoops that are sewn into the hem of bag.

• The hoops hold the mouth of the bag wide open while setting or packing the spinnaker.

Part No. Hoop Diameter (cm/in)Wire Diameter

(mm/in)Pack Qty

B232 41 / 16 4.8 / 3/16 10

B234 51 / 20 4.8 / 3/16 10

B236 61 / 24 4.8 / 3/16 10

SPINNAKER SNUFFER MATERIAL

A lightweight knitted 100% polyester ideal for spinnaker snuffer and socks.

Part No. Colour Roll Length (m) Width (mm/in)

FHKP60WT Optic White 50 1530

Rin

gs

& G

rom

met

s

Screw Post (SP)

Plug (P)

B530B521

Special order products.

98

Accessories


Self-Piercing Grommets & Washers SELF-PIERCING GROMMETS & WASHERS

Self-piercing grommets eliminate the need for hole punches, since the grommet cuts its own hole when being set. Increases speed and production efficiency. Saves time and frustration. Recommended for use in most industrial applications. Just load, pierce and set!

SELF-PIERCING GROMMETS/WASHERS

• Grommets and washers are sold as sets, and are available in brass, nickel plated brass or stainless steel.

• Manufactured from brass with a lacquer finish.

• Self-piercing grommets and washers are sold in full boxes only. 100 sets per box.

Part No. Material Size / Mfg # Inside Dia (mm/in)

D101B Brass 1 / 230 8 / 5/16

D102B Brass 2 / 250 10 / 3/8

SELF-PIERCING GROMMETS/WASHERS - NICKEL

• Manufactured from nickel plated brass with sharpened ground edge for penetrating into more difficult materials.



D111N Nickel Plated Brass 1 / 230 8 / 5/16



SELF-PIERCING GROMMETS/WASHERS STAINLESS STEEL

• Manufactured from stainless steel, which is sharper and stronger than either of the afore mentioned styles.



D112SS Stainless Steel 2 / 250 10 / 3/8

PRESS-N-SNAP DIES FOR SELF-PIERCING GROMMETS/WASHERS

• Self-holding press-n-snap grommet die sets for use with self-piercing grommets and washers.

Part No. Use With Size/Mfg #

C366 1 / 230

C367 2 / 250

BENCH PRESS DIES FOR SELF-PIERCING GROMMETS/WASHERS

• Self-holding bench press grommet die sets for use with self-piercing grommets and washers

• May be used with most US presses with 3⁄8 inch diameter shank.

Part No. Use With Size/Mfg #

C631 1 / 230

C632 2 / 250

C633 3 / 280

Top die holds grommet firmly

Grommet cuts its own hole and special grooved washer controls roll

over for a smooth secure fit.

Saves time and frustration!

Recommended for use in most industrial

applications.

Rin

gs

& G

rom

met

s

IMPORTANT NOTE

• Self-piercing grommets can only be set with self-piercing grommet dies. Neither plain washer nor spur grommet dies will work.

99

Accessories


Stimpson Grommets ENGLISH ROLLED RIM GROMMETS WITH SPUR TOOTHED WASHERS

• These grommets are sold in full packs only. 200 pieces per pack.

Part No. Material Size Reference Inside Dia. (mm/in)

D001BH Brass 000 5 / 3/16

D002BH Brass 00 6 / 1⁄4

D002NH Nickel 00 6 / 1⁄4

CLOSING TOOLS FOR ENGLISH GROMMETS

• Tools for English Grommets cannot be used with Stimpson Grommets.

Part No. Size

HC301 000

HC302 00

HOLE PUNCH AND CLOSING TOOL DATA FOR ENGLISH GROMMETS

Part No. SizeHole Punch Dia. (mm/in)

Hole Punch Closing Tool

D001BH 000 4.8 / 3/16 C181 C301

D002BH/NH 00 7.9 / 5/16 C182 C302

STIMPSON PLAIN RIM GROMMETS WITH PLAIN WASHERS

• These grommets are sold by the gross 144 sets per gross.

Part No. Material Size ReferenceInside Dia. (mm/

in)

D602B Solid Brass 00 4 / 5/32

D603B Solid Brass 0 6 / 1⁄4




D603N Solid Brass/Nickel Finish 0 6 / 1⁄4

D604N Solid Brass/Nickel Finish 1 8 / 5/16



D607N Solid Brass/Nickel Finish 4 12 / 1⁄2

CLOSING TOOLS FOR PLAIN GROMMETS

Part No. Size

C602S 00

C603S 0

C604S 1

C605S 2

C606S 3

C607S 4

HOLE PUNCH AND CLOSING TOOL DATA FOR PLAIN GROMMETS



D602B 00 5 / 3/16 C181 C602

D603B/N 0 6 / 1⁄4 C151 C603

D604B/N 1 8 / 5/16 C152 C604

D605B/N 2 10 / 3/8 C153 C605

D606B/N 3 11 / 11/16 C154 C606

D607N 4 12 / 1⁄2 C155 C607

Rin

gs

& G

rom

met

s

Cross section when set


100

Accessories


Stimpson Grommets STIMPSON SPUR-TOOTHED GROMMETS - BRASS FINISH

Self-piercing grommets eliminate the need for hole The higher strength of these spur-toothed grommets derives from their thicker metal gauge, and flange closing.

• Available only in full packs of 144 = 1 gross.

Part No. SizeSet Hole Diameter

(mm/in)Pack Qty

D003BS 0 6.4 / 1⁄4 144

D004BS 1 9.5 / 3/8 144

D005BS 2 10.3 / 13/32 144

D006BS 3 11.1 / 7/16 144

D007BS 4 14.2 / 9/16 144

D008BS 5 15.0 / 19/32 144

D009BS 6 17.4 / 11/16 144

STIMPSON SPUR-TOOTHED GROMMETS - NICKEL PLATED FINISH

The higher strength of these spur-toothed grommets derives from their thicker metal gauge, and flange closing.

• Available only in full packs of 144 = 1 gross.

Part No. SizeSet Hole Diameter

(mm/in)Pack Qty

D003NS 0 6.4 / 1⁄4 144

D004NS 1 9.5 / 3/8 144

D005NS 2 10.3 / 13/32 144

D006NS 3 11.1 / 7/16 144

D007NS 4 14.2 / 9/16 144

D008NS 5 15.0 / 19/32 144

D009NS 6 17.4 / 11/16 144

CLOSING TOOLS FOR STIMPSON GROMMETS

• Stimpson Grommets cannot be used with English Grommet tools.

• Stimpson tools are machined steel case hardened dies.

• Low-cost tools are drop forged steel dies.

Stimpson Part No. Low Cost Part No. Size

HC303S C303C 0

HC304S C304C 1

HC305S C305C 2

HC306S C306C 3

HC307S C307C 4

HC308S 5

HC309S 6

HOLE PUNCH AND CLOSING TOOL DATA FOR STIMPSON GROMMETS



D003BS/NS 0 9.5 / 3/8 C152 C303S

D004BS/NS 1 11.1 / 7/16 C153 C304S

D005BS/NS 2 12.7 / 1⁄2 C154 C305S

D006BS/NS 3 14.3 / 9/16 C155 C306S

D007BS/NS 4 15.9 / 5/8 C156 C307S

D008BS/NS 5 17.5 / 11/16 C157 C308S

D009BS/NS 6 22.2 / 7/8 C158 C309S

Rin

gs

& G

rom

met

s


FOR MAXIMUM PERFORMANCE AND SERVICE:

• Do not try to set grommet with one blow. Using Maul Master (C233/4) tap lightly at first, increasing strength of blow until grommet is set.

• Do not strike at an angle or attempt to dislodge a top set which has become wedged in a bottom die through over setting by striking a sharp blow on the side of the handle. Such misuse will cause the top set point to break, bottom set insert to chip, or both.

• Clean dies and lubricate periodically with Teflon Spray (M005).

101

Accessories


Stainless Steel & Titanium Rings

ROUND RINGS

• High grade stainless steel.

• TIG welded.

• Small diameter rings with the same size bar diameter will deform at a higher load although both will have similar tensile strength.

See Stainless Steel chapter

Part No.Inside Diameter

(mm/in)Bar Diameter

(mm/in)Weight (gm/oz)

Safe Working Load (kg/lb)

B214 25 / 1 4.8 / 3/16 14 / 0.5 300 / 700

B227 25 / 1 6.3 / 1⁄4 21 / 0.7 800 / 1800

B118 32 / 1 1⁄4 4.8 / 3/16 16 / 0.6 150 / 350

B117 32 / 1 1⁄4 6.3 / 1⁄4 28 / 1.0 600 / 1300

B228 32 / 1 1⁄4 7.9 / 5/16 49 / 1.7 1000 / 2200

B119 38 / 1 1⁄2 6.3 / 1⁄4 35 / 1.2 400 / 900

B219 38 / 1 1⁄2 7.9 / 5/16 57 / 2.0 750 / 1600

B229 38 / 1 1⁄2 9.3 / 3/8 85 / 3.0 1300 / 2800

B121 44 / 1 3⁄4 7.9 / 5/16 64 / 2.3 900 / 2000

B120 51 / 2 6.3 / 1⁄4 42 / 1.5 350 / 800

B220 51 / 2 7.9 / 5/16 71 / 2.5 550 / 1200

B221 51 / 2 9.3 / 3/8 106 / 3.7 1000 / 2200

B225 51 / 2 11.1 / 7/16 149 / 5.3 2300 / 5000

B223 64 / 2 1⁄2 9.3 / 3/8 127 / 4.5 750 / 1600

B224 76 / 3 7.9 / 5/16 106 / 3.7 250 / 550

“D” RINGS


• TIG welded.

See Stainless Steel chapter.


(mm/in)Bar Diameter



B170 25 / 1 4.8 / 3/16 14 / 0.5 300 / 700

B171 31 / 1 1⁄4 4.8 / 3/16 18 / 0.6 300 / 700

B172 38 / 1 1⁄2 4.8 / 3/16 21 / 0.7 300 / 700

B173 51 / 2 4.8 / 3/16 23 / 0.8 150 / 350

B174 51 / 2 6.3 / 1⁄4 42 / 1.5 500 / 1100

B175 60 / 2 3/8 7.9 / 5/16 64 / 2.3 700 / 1500

INVESTMENT CAST TITANIUM RING

• One-piece construction is achieved by investment casting the ring from Titanium.

• Eliminates weld weak points.

• Lightweight.

Part No. Inside Width (mm/in) Bar Diameter (mm/in)

B227T 25 / 1 6.5 / 1⁄4

B228T 32 / 1 1⁄4 8.0 / 5/16

B219T 38 / 1 1⁄2 8.0 / 5/16

“D” RINGS WITH BAR


• TIG welded.

• Reinforcing bar reduces potential distortion under high load and inhibits D-ring from rotating.


(mm/in)Bar Diameter



B174B 51 / 2 6.3 / 1⁄4 57 / 2 1300 / 2900

TRIANGLES


• TIG welded.

• Reinforcing bar reduces potential distortion under high load and inhibits D-ring from rotating.

See Stainless Steel chapter.


(mm/in)Bar Diameter



B127 51 / 2 6.3 / 1⁄4 49 / 1.7 500 / 1100

B128 76 / 3 7.9 / 5/16 113 / 4.0 750 / 1600

B127B 51 / 2 6.3 / 1⁄4 57 / 2.0 1000 / 2200

B127/B128 B127B

Rin

gs

& G

rom

met

s

STAINLESS STEEL WELDED HARDWARE

All Bainbridge International welded stainless steel fittings are manufactured from high grade stainless steel, which is chemically cleaned and passivated after welding to reduce the risk of staining. TIG welding maximizes strength.

102

Accessories


Stainless Steel Rings

MAXI RINGS


• TIG welded.

• Reinforcing bar reduces potential distortion under high load.


(mm/in)Bar Diameter



HB229B 38 / 1 1⁄2 9.3 / 3/8 106 / 3.7 2600 / 5700

HB221B 51 / 2 9.3 / 3/8

HB225B 51 / 2 11.1 / 7/16 191 / 6.7 4000 / 8800

HB226B 64 / 2 1⁄2 12.7 / 1⁄2 298 / 10.5 4500 / 9900

HB218B 76 / 3 15.8 / 5/8 568 / 20.1 10000 / 22000

CLEW PIECES


• TIG welded.

• Dist nctive pattern incorporates high strength with slots to secure webbing and prevents ring from rotating.


(mm/in)Bar Diameter



HB123 51 / 2 7.9 / 5/16 99 / 3.5 850 / 1900

HB124 64 / 2 1⁄2 9.3 / 3/8 156 / 5.5 1000 / 2200

HB125 76 / 3 11.1 / 7/16 276 / 9.8 2800 / 6200

HB126 96 / 3 3⁄4 12.7 / 1⁄2 446 / 15.8 3800 / 8400

HB122 4 1⁄4 5/8

CLEW PIECE WITH BAR/DIAMOND D RINGS

• The unique design enables webbing to be aligned with the stress lines of the sail.

• High grade stainless steel with TIG welds to yield maximum strength.

• Much stronger than mild steel version.

• Super strong design.

Part No. Inside Width (mm/in)Bar Diameter

(mm/in)Safe Working Load (kg/lb)

B163 50 / 2 8 / 5/16 1100 / 2000

B164 65 / 2 5/8 10 / 3/8 2000 / 4500

B165 75 / 3 11 / 7/16 3000 / 6600

CAST 17-4 STAINLESS STEEL SAIL RINGS

Unique computer design combined with high performance cast 17-4 stainless steel construction makes these sail rings lighter and stronger than comparable conventional welded rings. Easily webbed to the sail they are ideal for head and clew applications in mainsails, headsails and spinnakers.

• Lighter and stronger than conventional equivalent welded rings.

• Cast construction eliminates weld weak point.

• Made from 17-4 stainless steel, higher SWL than type 316.

• Elliptical cross-section and strengthening bar increase stiffness.

• Easy to web to sail.

• Can accommodate multiple sheets during sail or sheet point changes.

Part No.Length (mm/in)

Width (mm/in)

Bar Dia.(mm/in)

Weight (gm/oz)


HB248 74 / 2 15/16 58 / 2 5/169.3 x 6.4 /

3/8 x 1⁄473 / 2.6 2000 / 4400

HB250 92 / 3 5/8 72 / 2 7/810.5 x 7.2 /

7/16 x 5/16126 / 4.4 3000 / 6600

SPORTSBOAT CLEW RING

• Design for Sportsboats, small catamarans and skiffs with 2:1 jib sheet systems.

• Incorporates 2 Ronstan Series 30 ball bearing blocks.

• Sheave size 30mm, max rope 8mm/ 5⁄16 inch.

Part No.Inside Dia.

(mm/in)Bar Dia. (mm/

in)Weight (gm)


RF30286 29.5 / 1 3/16 4.8 / 3/16 65 / 2.3 160 / 352

Note: Safe working load is limited by the strength of the block.

Rin

gs

& G

rom

met

s

103

Accessories


Hooks, Eyes & Buckles EYE STRAPS

Part No. Description Pack Qty

G203S Stamped Stainless Steel 100

G204N Cast Nickel Plated Brass 100

G204S Cast Polished Stainless Steel 100

SNAP HOOK - WEBBING

• G200N/S has rectangular eye for webbing.

Part No. Material Length (mm/in)Inside Eye

(mm/in)Pack Qty

G200NNickel Plated

Brass50 / 2 25 / 1 100

G200S Stainless Steel 50 / 2 25 / 1 100

B617S Stainless Steel 50 / 2 25 / 1 100

SNAP HOOKS

• Brass snap hooks are an all purpose hook used in many applications where loads are relatively low.

• Stainless steel offers the same efficient and easy to use shape, but has much greater safe working loads.

Part No. Material TypeLength (mm/in)

Inside Eye (mm/in)

Pack Qty

B610 Brass 0 53 / 2 1/8 10 / 3/8 50

B611 Brass 1 72 / 2 7/8 15 / 5/8 50

B611NBrass/Nickel

Plate1 72 / 2 7/8 15 / 5/8 50

B612 Brass 2 81 / 3 1⁄4 20 / 3⁄4 5

B610S Stainless Steel 0 53 / 2 1/8 10 / 3/8 50

B611S Stainless Steel 1 72 / 2 7/8 15 / 5/8 50

B612S Stainless Steel 2 81 / 3 1⁄4 20 / 3⁄4 50

SWIVEL WEBBING BUCKLE WITH SOCKET

• Swivel pin allows installer to compensate for angles.

• Turn buckle 180° for easy removal from socket.

• Type 316 stainless steel.


G742S Swivel Web Buckle 50

SLIDING BAR BUCKLES

Part No. For Webbing (mm/in) Material Pack Qty

G221 25 / 1 Stainless Steel/Nylon 10

G221S 25 / 1 Stainless Steel 10

G222 50 / 2 Stainless Steel/Nylon 10


ADJUSTER BUCKLES

Part No. For Webbing (mm/in) Material Pack Qty

G210N 25 / 1 Nickel Plated Brass 100


A122BK 25 / 1 Plastic 100

Mar

ine

Co

ver

Fitt

ing

s

G203S

G204N

G204S

G200S

G200N

B617S

G210N G210S

A122BK

104

Accessories


Fasteners

STAYPUT FASTENERS

• Stayput fasteners are manufactured from UV stabilized nylon with nylon tabs and pivot pins.

• G850 - Horizontal single stud with two screw base. Works with No 1 spur or No 2 plain grommet.

• G852 - Vertical single stud with two screw base, Works with No 1 spur or No 2 plain grommet.

• G854 - Fitted through fabric or through a grommet.

See page 121 T-Toggles manufactured by QCD

Part No. Description Colour Pack Qty

G850 Horizontal Stud White 100

G852 Vertical Stud White 100

G854 Canvas-to-Canvas White 100

SNAPFAST

• Non-corrosive directional fastener.

• Unlocks in one direction.

• Stainless steel pronged cap self-pierces most fabrics.

• Install covers onto fiberglass, wood or other hard surfaces with no. 8 screw.

• Stud attaches to fabric with long eyelet.


G061 Stainless Steel – 100

G061LP Stainless Steel – 100

G062BK Socket Black 100

G062WT Socket White 100

G063BK Stud Black 100

G063WT Stud White 100

TENAX FASTENERS

• Used on superior quality boats and cars.

• Positive lock.


G165 Standard Pull Top with Lock Washer 10

G166 Cloth Base Stud with Lock Washer 10

G167 Wood Screw Stud 10

G167S Stud - Self Tap 10

G168 2 Screw Stud 10

G165TOOL Tool for Locating Ring 1

G164 #15 Machine Screw 10

PERMALOCK FASTENERS

• All manufactured from Dupont® non-corrosive, UV stabilized “Zytel”.

• Attach with flathead screws or rivets.

• Can be attached using 2 x G145/G147 eyelets.

• Available only in full packs of 100.


G160BK Single Stud with 2 Screw Base Black 100

G160WT Single Stud with 2 Screw Base White 100

G160ABK Backplate for Stud Black 100

G160AWT Backplate for Stud White 100

G161BK Eyelet Clinch Lock (2 Part) Black 100

G161WT Eyelet Clinch Lock (2 Part) White 100

C140 Eyelet Cutting Tool – 1

G160WT

G160AWT

G161WT

Turnbutton with Button Snap

Fastener Assembly

G165

G168 G165TOOL

G166G167 G167S

G164

G850

G852

G854

C140

G061 G062BKG063BK

Mar

ine

Co

ver

Fitt

ing

s

105

Accessories


Met

al F

aste

ners

Metal FastenersDURABLES

Custom designed logo can be added to Durable Caps. Minimum quantity is 30,000pcs. Price is on application and there is an initial design cost for the logo. Cap width - 15mm.

Stud

Gypsy Stud

Socket

Long Post

Plastic Washers

Carpet Fastener

Extra long Cap Long Cap Medium Cap Regular Cap

Regular Post

Windshield Clip

106

Accessories


Metal Fasteners

Met

al F

aste

ners

DURABLES – BRASS

Item Code Description / Finish Colour Cap lengths

CAPS

405XD Cap Extra Short Nickel, Black, Bronze, Brass 4mm (3/16”)

405XC Cap Regular Nickel, Black 5mm (7/32”)

405XE Cap Long Nickel, Black, Brass, Bronze 6mm (1⁄4”)

405XF Cap Extra Long Nickel, Black 11mm (7/18”)

COLOURED ENAMELLED CAPS

405ENXD Enamelled Cap RegularNavy, Black, Forest, White, Burgundy,

Dark Grey, Matt Black

4mm (3/16”)

405ENXC Enamelled Cap Medium 5mm (7/32”)

DURABLES – BRASS

Item Code Description / Finish Colour Post lengths

STUD

405XST Stud Nickel, Black, Bronze, Brass -

850-3EM20 Gypsy Stud Nickel 6mm

850-3-9EM20 Gypsy Stud Nickel 9mm

SOCKET

405X9.65 Easy Action Socket Nickel, Black, Bronze, Brass -

405X9.5 Medm Action Socket Nickel, Black, Bronze -

405XHA Stiff Action Socket Nickel, Black -

850-8M20

850-9M7

Carpet Fastener Socket and

Prong Set

Prong - Black

Socket - Nickel-

POST

405XPN Post Regular Nickel, Black, Bronze, Brass 7.5mm (5/16”)

405XPL Post Long Nickel, Black 8.5mm (11/32”)

405XW Plastic Washer -

107

Accessories


Metal FastenersDURABLES – STAINLESS STEEL

Item Code Description Cap/Post lengths

CAPS

405SSXD Cap Extra Short 4mm (5/32”)

405SSXA Cap Regular 5.25mm (7/32”)

405SSXE Cap Long 6mm (1⁄4”)

SOCKET

405SSX9.65 Easy Action Socket

405SSX9.5 Medium Action Socket

405SSX9.4 Stiff Action Socket

STUD

405SSXST Stud

405XSTSC10 Stud with 10mm screw

405XSTSC16 Stud with 16mm screw

WINDSHIELD CLIPS

850-6-19 Windshield Clip 3⁄4” (19mm)

850-6-22 Windshield Clip 7/8” (22mm)

POST

405SSXPN Post – Regular 7.5mm (5/16”)

405SSXPL Post – Long 8.5mm (11/32”)

405XW Plastic Washer

DURABLES – QUICK-FIT

Quick-fit holding tools snap onto existing studs and provide a quick and easy way to hold material while fitting boat covers. Plastic holding cap fits onto the pin holding the material in place. Quick-fit tools can be used over and over again. Accurately mark the cover as to where sockets should be placed. Also refer to page 115.

Item Code Description

C896 Quick-fit Pin with Socket

C896CAP Quick-fit Plastic Cap

C897 Quick-fit Removing Tool

DURABLE HAND DIES


Durable Hand Dies

Post Base

Stud/Socket PunchCap Base

DDHC Cap Base

DDHP Post Base

DDHS/ST Stud/Socket Punch

Complete Set

Met

al F

aste

ners

108

Accessories


Metal Fasteners

Met

al F

aste

ners

DURABLES – BRASS

Durable Machine Dies Item Code Description

DDC Cap 3/8” Shaft Die

DDP Post 3/8” Shaft Die

DDS Socket 3/8” Shaft Die

DDST Stud 3/8” Shaft Die

Complete Set

BABY DURABLES – BRASS

Custom designed logo can be added to Durable Caps. Minimum quantity is 30,000 pcs. Price is on application and there is an initial design cost for the logo. Baby Durables have the same system as standard durables but in a smaller size. Baby Durables have a diameter of approximately 12mm as compared to standard Durables 15mm. Available in Nickel, Bronze and Black Plated Finishes

Item Code Description / Finish Colour Cap/Post lengths

CAP

406XD Cap RegularBronze, Brass, Nickel, Black

3.0mm

406XE Cap Long 4.0mm

SOCKET

406XSOCK Socket Bronze, Brass, Nickel, Black

STUD

406XST Stud Bronze, Brass, Nickel, Black

POST

406XPN Post Bronze, Brass, Nickel, Black 7.5mm (5⁄16”)

BABY DURABLE MACHINE DIES

Durable Machine Dies Item Code Description

DBDC Cap 3/8” Shaft Die

DBDP Post Base 3/8” Shaft Die

DBDS Socket 3/8” Shaft Die

DBDST Stud 3/8” Shaft Die

Complete Set

109

Accessories


Metal FastenersDURABLE G-CLAMP TOOL


HC360

The versatile and easy to use G-Clamp is used for the setting of durable snap fasteners. The dies have

rubber retainers to hold the fasteners in place during installation.

The heat-treated cast-aluminum body makes it both lightweight and durable, ensuring you years of trouble

free service. Each tool comes with a complete set of dies (including rubber rings).

Completely mobile, the G-Clamp is ideal for boat and motor trimmers as you can take the setting tool

directly to the job.

DURABLE G-CLAMP REPLACEMENT PARTS


G CLAMP DIES

HC374 Cap

HC379 Post

DDG-SO Socket

DDG-ST Stud

RUBBER RINGS

DRR Replacement Rubber Grommets


BABY DURABLE DIES

DDG-C/B G Clamp Baby Cap Die

DDG-P/B G Clamp Baby Post Die

DDG-SO/B G Clamp Baby Socket Die

DDG-ST/B G Clamp Baby Stud Die

Met

al F

aste

ners

110

Accessories


Met

al F

aste

ners

893T & W 894 895 896

897E & W

900T & W

905

902T &

892-3W

905-2

904

906

904-2

906-2

Metal Fasteners

SUPER SPOT FASTENERS TURN BUTTON FASTENERS

Metal FastenersTOMAX FASTENERS

The TOMAX closure is a highly engineered, self-locking snap fastener that cannot come undone once engaged, yet it releases instantly by simply pulling upon the head of the button component. Manufactured from brass and nickel plated, the TOMAX product range is often seen in use on a number of British automotive applications, but because of the uniqueness of the TOMAX system, it is an ideal choice for marine upholstery.

20011 & 20010

20012T & W

20014

20014L

20016

20016L

20018

20018L

20020 Locking Key

111

Accessories


Metal FastenersTOMAX FASTENERS


BUTTON

20011 Tomax Button Large

20010 Tomax Backing Washer/nut

Set of the Above

STUD PLATES

20018 Stud with 2 Hole Plate

20018LStud with 2 Hole Plate –

Low Profile

CLOTH-CLOTH STUD

20012T Stud Cloth/Cloth

20012W Stud Cloth/Cloth Washer/nut

Set of the Above

SELF TAPPING STUD

20014 Stud with Wood Screw

20014LStud with Wood Screw –

Low Profile

STUD WITH THREADED NUT

20016 Stud with Thread & Nut

20016LStud with Thread & Nut –

Low Profile

TOOL

20020 Tomax Washer Locking Key

Met

al F

aste

ners

112

Accessories


Metal Fasteners

Met

al F

aste

ners

TURN BUTTON FASTENERS


EYELET

897E Prong Eyelet

897W Clinch Plate for Prong Eyelets

Set of the Above

TURNBUTTON

894 Turnbutton 6mm High – 2 Hole



CLOTH–CLOTH TURNBUTTON

893T Turnbutton 7mm High – Cloth/Cloth

892-3W Clinch Plate Cloth/Cloth

Set of the Above

TURN BUTTON TOOLS


897HP Hand Cutting Die for Prong Eyelet

DEZ-TBEZ Turnbutton Hole Cutter – Ezi Tool

Used for cutting holes in fabric for Turnbutton fasteners

113

Accessories


Metal FastenersSUPER SPOT FASTENERS


SOCKET

900T Super Spot Fastener

900W Clinch Plate for Super Spot Fastener

Set of the Above

STUD PLATES

904 Single Stud 2 Hole – Pressed Brass Plate

904-2 Double Stud 2 Hole – Solid Brass Plate

CLOTH-CLOTH STUD

902T Stud with Prongs

892-3W Clinch Plate Cloth/Cloth

Set of the Above

SELF TAPPING STUD

906 Single Stud with Wood Screw

906-2 Double Stud with Wood Screw

STUD WITH THREADED NUT

905 Single Stud with Screw on Nut

905-2 Double Stud with Screw on Nut

SUPER SPOT FASTENER TOOLS


900HPHand Cutting Die for Super

Spot Fastener

DEZ-SSFEZ Superspot Fastener Hole Puncher

Used for cutting holes in fabric for Superspot fasteners

Met

al F

aste

ners

114

Accessories


DOT® Fasteners

BUTTON SNAP FASTENER

When superior snap action and holding strength is needed, the durable DOT fastener is the one to use, it is self-piercing, so no pre-punching is required, the durable DOT fastener’s heavy-duty construction assures a firm grip that will remain secure through years of use.

• All manufactured in nickel plated brass.

• May be used with Quick-Fit locating tools.


Part No. Description Mfr #

G140 Nickel Button with 5mm/ 3/16" Barrel 93-X2-10128

G140BU Pacific Blue Button with 5mm/ 3/16" Barrel 93-XV-10150

G140BK Black Button with 5mm/ 3/16" Barrel 93-XV-10150

G140WT White Button with 5mm/ 3/16" Barrel 93-XV-10150

G140NV Navy Button with 5mm/ 3/16" Barrel 93-XV-10150

G141 Nickel Button with 6.5mm/ 1⁄4" Barrel 93-X2-10127

G141L Nickel Button with 10mm/ 3/8" Barrel 93-X2-10127

G142 Regular Action Socket 93-XB-10224

G145 Eyelet with 6.5mm/ 1⁄4" Barrel 93-BS-10412

G146 Eyelet with 8mm/ 5/16" Barrel 93-BS-10413

G147 Eyelet with 10mm/ 3/8" Barrel 93-BS-10414

G155 Stiff Action Socket 93-XX-10224

BUTTON SNAP FASTENER SPECIALTY STUDS

• All manufactured in nickel plated brass/stainless steel.



G143 Stud for use with Eyelet 93-BS-10370

G144 Deep Stud 93-BS-10379

G174 Rivet Stud 3.2mm/ 1/8 " 93-10314

G148 Stud, Reversible Type (use with G142) 93-XB-10342

G156 20mm/ 3⁄4 " Windshield Clip 93-10388

G157 28.6mm/ 7/8 " Windshield Clip 93-10391

G182 Flangeless Stud 93-10373

STAINLESS STEEL BUTTON SNAP FASTENER

• The new all stainless steel DOT Buttons are stronger than the standard brass/nickel buttons, and also resist corrosion.

• The stainless steel barrels allows it to self-pierce through a greater variety and thickness of material without the need for pre-punching.

• The brass/nickel plated cap with stainless steel style self-pierces through nylons, Dacrons and webbings.

• G140BS - this button offers greater strength, higher quality than standard with low additional cost.



G140SS S.S. Button with 4.8mm/ 3/16 " S.S. Barrel 93-XN-10128

G140BS Brass/Nickel Button with 4.8mm/ 3/16 " S.S. Barrel 93-XB-10128

G141SS S.S. Button with 6.4mm/ 1⁄4 " S.S. Barrel 93-XN-10128

G142SS S.S. Regular Action Socket 93-XN-10224

G143SS S.S. Stud for use with Eyelet 93-NS-10370

G145SS S.S. Eyelet with 6.5mm/ 1⁄4 " Barrel 93-NS-10412

G149SS Easy Action S.S. Socket 93-XN-10225

BUTTON SNAP FASTENER SCREW STUDS

• Manufactured in nickel plated brass.


• Screws in brass or stainless steel.


G152OS Stud with Oversize S.S. Screw (No.10 Deep Phillips x 15.9mm/ 5⁄8 ")

93-10934

G151 Stud with 10mm/ 3⁄8" Phillips Head Screw (No. 8) 93-X8-103934-12

G151SS Stud with S.S. 10mm/ 3⁄8" Phillips Head Screw (No. 8) 93-XN-103934-12

G152 S.S. Stud with 15mm/5⁄8 " Phillips Head Screw (No. 8) 93-X8-103937-20

G153 Stud w. Phillips Head (No. 10-32 Brass Machine x 9.5mm/ 3⁄8 ")

93-XB-10708-12

G154 Stud w. Phillips Head (No. 10-32 Brass Machine x 15.9mm/ 5⁄8 ")

93-XB-10708-20

G171 Self-Drilling S.S. Screw (No. 10 Deep Phillips Head x 12.7mm/ 1⁄2 ")

93-10301-14

G175 Self-Drilling S.S. Screw (No. 10 Deep Phillips Head x 20mm/ 3⁄4 ")

93-10301-20

G171FW Plastic Flexi-Washer for Eyelet, Button or Studs

Mar

ine

Co

ver

Fitt

ing

s®

Special Pricing on

10 pack

G145G143

G140 G142, G155

G145SS

G143SSG140SS/G140BS

G142SS/G149SS

G153 G154

G152OS

G171 G175

G171FW

G151 G151SS

G143

G156/G157

G148G144

G182G174

115

Accessories


Button Snap (Durable Dot) Fastener Assembly

C896 CapC896C897

Holding Cap

Release Tool

Fit Pin Socket

DOT® FastenersTOOLS FOR USE WITH BUTTON SNAP/ DURABLE DOT FASTENERS

Fastener Part No. Bench Press Tool Part No. Hand Tool Part No. Press-N-Snap

G140 C941A C954/C955 C361

G141 C941A C954/C955 C361

G142 C941B C954/C955 C361

G143 C942A C954/C955 C361

G145 C942B C954/C956 C361

G146 C942B C954/C956 C361

G147 C942B C954/C956 C361

G148 - - C474

QUICK-FIT CANVAS TOOLS

• Quick-Fit holding tools snap onto existing studs and provide a quick and easy way to hold material while fitting boat covers. Plastic holding cap fits onto the pin, holding the material in place.

• Quick-Fit tools may be used over and over.

• Great for fitting with material and also holding paper or plastic material patterns.

• Accurately mark the cover as to where sockets are placed.

• Use on tonneau covers, cockpit covers, side curtains, enclosures, biminis, dodgers, etc...

• Kit contains 50 fit pins, 25 holding caps and 1 release tool.


C896CAP Plastic Holding Cap each

C896 Fit Pin Socket 50/box

C897 Release Tool each

C896KIT Kit each

SNAP FASTENER HAND SETTING TOOLS

Part No. Description Use With Fastener

C954 For Buttons or Eyelets C955/956 G140/1/2/3/5/6/7

C955 For Durable Button C954 G140/1

C956 For Durable Eyelet C954 G145/6/7

PULL-THE-DOT FASTENERS

• A heavy,duty, three sided locking snap fastener that is built to withstand extreme pressure on three sides without unlocking.

• When pulled on the fourth side where the Pull-the-Dot trademark appears, the fastener releases instantly.

• DOT fasteners are sold in full packs of 100 only.


G170 Pull-the-Dot Button Cap 92-18100

G172 Pull-the-Dot Socket 92-18201

G173 Pull-the-Dot Stud 92-18303

G176 Pull-the-Dot Screw Stud 92-18307

G145 6.4mm/ 1⁄4 " Post 93-10412

G146 7.0mm/ 5⁄16 " Post 93-10413

Note: Special tools are required for Pull-the-Dot G170, G172 and G173.

Mar

ine

Co

ver

Fitt

ing

s

®

G170 G173

G172

G176 G146

C954

C955 C956

116

Accessories


COMMONSENSE TURNBUTTON FASTENER STUDS

Traditional fastenings for boat and marine covers and canvas work, recommended by Bainbridge International, for incorporating secure fastening combined with easy access.

• All manufactured in nickel plated brass.



G100 Single Stud with 2 Screw Base 91XB78322

G101 Double Stud with 2 Screw Base 91XB78323

G103A Single Stud with 2 Prong Fastener Stud 91XB78332

G102A Double Stud with Two Prongs 91XB78333

G103BP Clinch Plate for Studs with Two Prongs 91XB78507

G106 Single Stud with Brass Screw (No.7 x 15mm/ 5⁄8 ") 91XB78324

G106S Single Stud with Stainless Steel Screw (No.7 x 15mm/ 5⁄8 ") 91XB78324

G107 Double Stud with Brass Screw (No.7 x 15mm/ 5⁄8 ") 91XB78325

G108 Single Stud with Rivet Base 91BS78317

G108BP Backplate for Rivet Base 91BS78502

G101FW Flexiwasher for G100/G101 91BS78522

G155 Stiff Action Socket 93-XX-10224

COMMONSENSE TURNBUTTON FASTENER EYELETS

• All manufactured in nickel plated brass.• Available only in full packs of 100.• G105FW used to protect fabric from chafe.


G104A Eyelet with Regular Prongs 91BS78403

G105A Eyelet with Long Prongs 91BS78404

G104BP Washer for G104A/G105A 91BS78505

G105MW Metal Washer for Eyelet 91BS78510

G105FW Plastic Flexi-washer for Eyelet 91PS78511

DO

T® F

aste

ners

DOT® FastenersCOMMONSENSE CUTTING PUNCHES

• To prolong life of tool, use a mallet and a cutting pad.


C950 Cutting Punch G102A

C951 Heavy Duty Cutting Punch G103A

TOOLS FOR USE WITH COMMON SENSE FASTENERS

Fastener Part No. Hand Tool Part No.

G102 C950

G103 C950

G104 C951 or C136

G105 C951 or 136

TYLASKA SNAP SETTER

A new die solves the problem of setting two fasteners at once, by having two precisely spaced cavities allowing two buttons or eyelets to be installed at the same time.

• Time saving tool.

• Made from chrome-moly aerospace steel and is heat treated.

Part No. Description

C959 Button and Eyelet Tool

G100

G103A G108

C950 C951

G108BPG103BPG106/107

G104A G105MW

G104BP G105FW

G101FW

Turnbutton Fastener Assembly

INFORMATION

NOTE: One side is for 2 x buttons G140 and the other side is for 2 x eyelets G145.

®

117

Accessories


DO

T® F

aste

ners

DOT® FastenersLIFT-THE-DOT® FASTENER STUDS

• All manufactured in nickel plated brass.• Available only in full packs of 100.


G110 Single Stud with 2 Screw Base 90X316347

G120A Rivet Stud 90XB16358

G120BP Washer for Rivet Stud 90BS16509

G119A Single Stud with Two Prong 90BS16349

G119BP Clinch Plate for G119A 90BS16501

G113 Stud with Machine Brass Screw 90XB16362-12

G115S Stud with 10mm/ 3⁄8 " Stainless Steel Screw 90XB16360-12

G116S Stud with 15mm/ 5⁄8 " Stainless Steel Screw 90XB16360-20

G103BP Clinch Plate for Stud with 2 Prongs 91BS78507

G117 3⁄4 " Windshield Clip 90X816376

G118 7⁄8 " Windshield Clip 90X816377

LIFT-THE-DOT® FASTENERS

• All manufactured in nickel plated brass.• Available only in full packs of 100.• G119FW used to protect fabric from chafe on eyelet.


G130A Regular Socket 90XX16205

G130LP Long Prong Socket 90XX16206

G130BP Clinch Plate for Socket 90BS16506

G119FW Plastic Flexi-washer for Eyelet 90BS16510

LIFT-THE-DOT® TOOLS

• To prolong life of tool, use a mallet and a cutting pad.

Part No. Description Fastener

C950 Cutting Punch G119

C952 Hand Set Hex Head G113/115/116

C953 Cutting Punch G130

TOOLS FOR USE WITH LIFT-THE-DOT FASTENERS

Fastener Part No. Bench Press Tool Part No.Hand Tool Part

No.Press-N-Snap

G113 – C952 –

G115 – C952 –

G116 – C850 –

G119 – C952 –

G120 C944A – C368

G120A C944B – C369

G130 C945 C135/C953 –

G120BP

G110

G113

G116S

G120A

G103BP

G119BP

G119A

G117

Special Pricing on 10 pack

G119FWG130BP G130A

C950

C952

C953

Lift-the-Dot Fastener Assembly

®

118

Accessories


SNAPMASTER M840

• The DOT Snapmaster M840 hand-operated attaching press for snap fasteners offers many features of the larger and heavier bench and foot presses, yet is entirely portable and comes in its own carrying case. There are now specialized dies which enable the user to pre-punch the BS78403 and BS78505 eyelet and washer for the Common Sense fastener as well as setting Button fasteners.

• The Snapmaster is a rugged tool of all aluminum and steel construction with a warranty direct from the manufacturer.

• Snapmaster M840 comes with carrying case of rugged nylon.


C930 Snapmaster M840 - Use with Only Snapmaster Dies

DIES FOR THE SNAPMASTER M840

Part No. Mfg # Description Use With

C931A 4103 Common Sense Top Punch G104A/G104BP

C931B 4203 Common Sense Bottom Punch G104A/G104BP

C932A 4403 Button Snap Top Setting Die G140/G141

C932B 4303 Button Snap Bottom Setting Die G142/G155

C933A 4304 Button Snap Top Setting Die G143

C933B 4404 Button Snap Bottom Setting Die G145

C934A 4101 Lift-the-Dot Top Punch G130A

C934B 4201 Lift-the-Dot Bottom Punch G130BP

Fast

ener

To

ols

Fastener ToolsBENCH PRESS

• Deep throat and long padded handle improves leverage.• Easily sets snap fasteners or self-piercing grommets.• Light weight aluminum - ideal for portable applications where strength and weight savings are critical.• Bench press machine will accept most dies with 9.5mm/ 3⁄8 inch shank.

Part No. Material Throat Depth mm/in Approx Weight lbs Use With Dies

C620 Steel 121 4 3⁄4 12 C941-5

DIE TOOLS FOR USE WITH BENCH PRESS

• All dies have 9.5mm/ 3⁄8 inch diameter shank.

Part No. Die Mfg # Use With

C941A Top 1401 G140/G170 - Button

C941B Bottom 1410 G142/G155/G172 - Socket

C942A Top 1412 G143/G173 - Stud

C942B Bottom 1407 G145/G146/G147 - Eyelet

C944A Top 1456 G120 - Rivet Stud

C944B Bottom 1457 G120 - Rivet Stud

C931A

C932A

C933A

C934A

C931B

C932B

C933B

C934B

C941B

C942B

C944B

C941A

C942A

C944A

Accessories

QCD Limited, 28 Hargreaves Street, Ponsonby, Auckland 1011, New Zealand | PO Box 47760, Ponsonby, Auckland 1144, New Zealand Phone: +64 9 366 7118 | Freephone: 0800 240 040 | Fax: +64 9 366 7119 | E-mail: [email protected] 119

DO

T® F

aste

ners

DOT® FastenersLEVER ACTION HAND TOOLS

• All manufactured in nickel plated brass.• Available only in full packs of 100.

Part No. Description For Use With

C135 Hole Cutter for Lift-the-Dot Sockets G130A

C136 Hole Cutter for Common Sense Eyelets G104A, G105A

VISE PLIERS AND ATTACHMENTS

• HC371 - Four piece set

Part No. Description For Use With

HC370 Vise Pliers HC371

HC371 Die Set for Button Snap Fasteners G140/ 7

DIES FOR SELF-PIERCING GROMMETS

• Self holding Press-N-Snap grommet dies for use with self- piercing grommets and washers.

• Two piece sets.

Part No. Size Mfg #

HC366 Size 1, D101 or D111 230

HC367 Size 2, D102 or D112 250

PRESS-N-SNAP TOOL

• A hand action tool for closing grommets, rivets and setting button snap fasteners.

• HC360 tool comes complete with die sets for No1 washer grommets and Button Snaps.

Part No. Description Fastener

HC360 Press-N-Snap Tool G140/ 147, D604

DIES FOR PRESS-N-SNAP TOOL

• HC361 - Four piece set.• HC362/363 - Two piece sets.

Part No. Bench Press Tool Part No. For Use With

HC361Button Fasteners, Set (Includes 1 Washer Grommet

set)G140 /7

HC362 No 0 Spur Grommet, Set D003

HC363 No 1 Spur Grommet, Set D004

HC361GYW Spare Gray Washer

HC361BKW Spare Black “O” Ring –

HC368 Die for L-T-D Washer #8 G120BP

HC369 Die for L-T-D Stud #58 G120A

HC374 Die for Gypsy Stud #22 G148

C135 C136

HC370

HC371

HC374

HC361

HC362

HC361GYW

HC361BKW

120

Notes



Notes

121

Accessories



Met

al/P

last

ic F

aste

ners

Metal/Plastic FastenersT-TOGGLES WITH METAL FLIPPER

All T-Toggles are available in Black & White

SINGLESItem Code

Description

SPMVS T-Toggles Vertical Single with METAL Flipper - White

SPMVSB T-Toggles Vertical Single with METAL Flipper - Black

SPMHS T-Toggles Horizontal Single with METAL Flipper - White

SPMHSB T-Toggles Horizontal Single with METAL Flipper - Black

SPMCCST-Toggles Canvas to Canvas Single with METAL Flipper - White

(Includes nuts)

SPMCCSBT-Toggles Canvas to Canvas Single with METAL Flipper - White

(Includes nuts)

DOUBLESItem Code

Description

SPMVD T-Toggles Vertical Double with METAL Flipper - White

SPMVDB T-Toggles Vertical Double with METAL Flipper - Black

SPMHD T-Toggles Horizontal Double with METAL Flipper - White

SPMHDB T-Toggles Horizontal Double with METAL Flipper - Black

SPMCCDT-Toggles Canvas to Canvas Double with METAL Flipper - White

(Includes nuts)

SPMCCDBT-Toggles Canvas to Canvas Double with METAL Flipper - Black

(Includes nuts)

T-TOGGLES - STAINLESS STEEL 316 GRADE

SINGLESItem Code

Description

QCDTVS T-Toggles Vertical Single Stainless Steel 316

QCDTHS T-Toggles Horizontal Single Stainless Steel 316

DOUBLESItem Code

Description

QCDTV T-Toggles Vertical Double Stainless Steel 316

QCDT T-Toggles Horizontal Double Stainless Steel 316

122

Accessories


Pla

stic

Fas

tene

rs

Plastic FastenersT-TOGGLES WITH METAL FLIPPER

HOOKSItem Code

Description

SPMHK T-Toggles Annex Hook

SPMH T-Toggles Marquee Hook

CANVAS TO CANVAS NUTSItem Code

Description

SPCCN T-Toggles Canvas to Canvas Nut Only

CAMLOC BUCKLES

Camloc Buckles provide an easy-to-use and easy-to-adjust means of securing webbing. The locking doors trap the webbing to prevent unintentional slippage.The “robust” design and glass filled nylon material used for manufacture of the Camloc buckle, ensures maximum performance when securing webbing.

Item Code

Size (mm) Description In Bags of

380-0324 20 Camloc 20mm 100

380-1093 25 Camloc 25mm 100

380-1086 50 Camloc 50mm 100

123

Accessories


Pla

stic

Fas

tene

rs

Plastic FastenersTRI GLIDES

The Tri-Glide strap adjuster provides length adjustment on strap assemblies. The Tri-Glides grip webbing securely and work well in combination with other buckles as a means of securing loose webbing. The Tri-Glides are available in many sizes and styles to accommodate an assortment of webbing widths and thicknesses.

Item Code

Size (mm) Size (inches) Height (mm) In Bags of

PK2824/19 19 3⁄4 inch 22 100

PK2824/25 25 1 inch 22 100

PK2824/38 38 1 1⁄2 inch 33 100

PK2824/50 50 2 inch 38 100

SNAP HOOKS

Item Code


FSH25 25 Fastex Plastic Rotating Snap Hook 25mm 100

BARRELOCS

SINGLESItem Code

Description In Bags of

PK2704Small – Round without cap. With metal spring

(Suits up to 3mm cord)100

PK2708Small – Square without cap. With metal spring


PK2707Large – Rectangular with cap and Plastic Spring


ZIPPER PULLS

SINGLESItem Code


PK2728Zipper Pull


124

Accessories


Pla

stic

Fas

tene

rs

Plastic FastenersSIDE RELEASE BUCKLES – STANDARD

Item Code


PKSRB/1919

(¾ inch)Side Release Buckle to fit 19mm webbing 100

PKSRB/2525

(1 inch)Side Release Buckle to fit 25mm webbing 100

PKSRB/3232

(1¼ inch)Side Release Buckle to fit 32mm webbing 100

PKSRB/3838

(1½ inch)Side Release Buckle to fit 38mm webbing 100

PKSRB/5050

(2 inch)Side Release Buckle to fit 50mm webbing 100

SIDE RELEASE BUCKLES - ITW FASTEX CLASSIC

The Fastex “Classic” style of side release buckle has stood the test of time. Meticulously engineered to provide superior strength the “Classic” style buckle is still the preferred shape used by the Australian Defence Force and a number of semi-military or government style organisations.

Item Code


950-115625

(1 inch)Fastex Classic Side Release Buckle to fit 25mm webbing 100

950-111450

(2 inch)Fastex Classic Side Release Buckle to fit 50mm webbing 100

SIDE RELEASE BUCKLES – ITW FASTEX

Manufactured by ITW NEXUS, the World Side Release buckle offers many structural and aesthetic features not found in other side release buckles. The addition of a centre support rib for crush resistance, and a reduction in overall length of the buckle, are just a few of the many features of the WSR. Both 40mm and 50mm versions have a contoured profile to improve user comfort.

Item Code


950-1142 19 (¾ inch) Fastex World Side Release Buckle to fit 19mm webbing 100

950-1135 25 (1 inch) Fastex World Side Release Buckle to fit 25mm webbing 100

950-1119 40 (1½ inch) Fastex World Side Release Buckle to fit 40mm webbing 100

950-1113 50 (2 inch) Fastex World Side Release Buckle to fit 50mm webbing 100

125

Accessories


Pla

stic

Fas

tene

rs

Plastic FastenersSIDE RELEASE BUCKLES – TROVATO FASTEX

“TROVATO” Side Release Buckles

The Fastex “Trovato” range is our premium range of side release buckles that have been engineered to provide maximum strength and performance.

Complementing this is the stylish design and high quality surface finish making the “Trovato” series both extremely pleasing to the eye as well as ideal for side release applications.

Item Code


FTSR1919

(¾ inch)

Fastex Trovato

Side Release Buckle to fit 19mm webbing100

FTSR2525

(1 inch)

Fastex Trovato


FTSR3838

(1½ inch)

Fastex Trovato


FTSR5050

(2 inch)

Fastex Trovato


FTSRD5050

(2 inch)

Fastex Trovato Dual Ladderlok


SPECIALITY BUCKLES – FASTEX

The patented Lockable Side Release Buckle has been designed to offer the normal side release functionality with the added advantage of a key driven locking mechanism that restricts the ability to open the buckle.

The LJ25 buckle has been developed to provide superior locking strength with anti-pinching characteristics, making this part an excellent choice for safety vests.

Item Code


FX-3801100 25mm Lockable Side Release Buckle to fit 25mm webbing 100

FX-3861101 N/A Keys for Lockable Side Release Buckle 100

FX-9501195 25mmLJ 25 Heavy Locking Action Side Release Buckle to fit 25mm

webbing100

126

Accessories


Pla

stic

Fas

tene

rs

Plastic FastenersPLASTIC D-RING

Item Code

Description

386-0156 Plastic D-Ring 25mm

PLASTIC LOOPLOK

Item Code

Description

386-0301 Fastex Looploc 19mm


FX-3860838 Fastex Looploc 38mm


MILITARY – SIDE RELEASE BUCKLES – CLASSIC

ITW Fastex have been supplying military style buckles and accessories for in excess of 15 years.

Manufactured from a special toughened grade of Khaki coloured Nylon, the buckles are designed to provide maximum performance for applications where functionality is critical.

Item Code


FX-3800946 19 Fastex Khaki

Side Release Buckle Classic to fit 19mm webbing100

380-0816-PK 25Fastex Khaki


FX-3800928 50Fastex Khaki


FX-3800934 60Fastex Khaki


MILITARY – HEAVY DUTY SIDE RELEASE BUCKLE

Item Code


950-1232-PK 25 Khaki Heavy Duty Side Release Buckle to fit 25mm webbing 100

127

Accessories


Pla

stic

Fas

tene

rs

Plastic FastenersMILITARY – TRI GLIDES

Item Code

Size (mm) Size (inches) Description In Bags of

FX-3860289 25 1 inch Fastex 25mm Khaki Tri Glide 100

FX-3860988 50 2 inchFastex

50mm Khaki Tri Glide100

MILITARY – LADDERLOKS

Item Code


FX-3860064 25Fastex Ladderlok 25mm

Khaki100

FX-3860761 25Trovato Super Ladderlok 25mm

Khaki and Black100

MILITARY – ACCESSORIES

Item Code


FX-3860717 25 Fastex Khaki D-Ring 25mm 100

FX3860141 N/A Khaki Barrelok Large 100

PKICLCE 50mm ICLCE Clip Khaki 50mm 100

LADDERLOKS

Ladderlok adjustment buckles are the most versatile buckles, allowing easy, one-handed release or tightening of webbing and straps. All Ladderloks have been designed to minimise slippage of the webbing while allowing smooth and easy tightening.The “Trovato” Super Ladderlok combines this versatility with a robust body making it suitable for those heavy-duty applications.

Item Code Size (mm) Description In Bags of

386-0072 19 Fastex Ladderlok 19mm Black 100

386-0063 25 Fastex Ladderlok 25mm Black 100

386-0706 20 Trovato Super Ladderlok 20mm Black 100

956-1109 25 Trovato Super Ladderlok 25mm Black 100

MILITARY – SIDE RELEASE TUCK BUCKLES

Item Code


FX-3861193 25 Khaki Tuck


128

Accessories


Plastic Fasteners – Hook & LoopQCD HOOK & LOOP

This Nylon fastener is a two part system; one part consisting of rows of hooks and the other part of a mass of loops. When pressed together, they form a highly secure closure, yet can be easily re-opened with a simple peeling action. Available in sew on and pressure sensitive adhesive backed forms.

SPECIFICATIONS:

Excellent properties for thermo-resistance, chemical resistance and electrical insulation.

Heat resistance: Becoming soft at 180ºC and melted at 215ºC.

Cold Resistance: Useable to -30ºC, the lower the temperature, the stronger the tensile force.

Item Code Description Width (inches) Width (mm) Sppols in length (metres) Box Quantity

V16H Hook 5/ 8” 16 25 30

V16L Loop 5/ 8” 16 25 30

White Black

V20H Hook 3⁄4” 20 25 24

V20L Loop 3⁄4” 20 25 24

White Red Navy Black Fluro Yellow

V25H Hook 1” 25 25 20

V25L Loop 1” 25 25 20

White Beige Navy Black Grey

Yellow Red Army Royal Blue

V38H Hook 1 1⁄2” 38 25 14

V38L Loop 1 1⁄2” 38 25 14

White Black

V50H Hook 2” 50 25 10

V50L Loop 2” 50 25 10

White Beige Navy Black Grey

Yellow Red Army Royal Blue

V100H Hook 4” 100 25 5

V100L Loop 4” 100 25 5

White Black

Pla

stic

Fas

tene

rs -

Ho

ok

& L

oo

p

129

Accessories


SELF ADHESIVE – ACRYLIC ADHESIVE

Self Adhesive Tape is an acrylic pressure sensitive adhesive for high temperature performance and superior bond strength for uses in automotive, computer, medical and other industries.

• Moderate tack – medium set up

• High Strength

• High Temperature use

• Full bond strength – 24 hours

• Temperature operating range -20ºC to 110ºC

Item Code Description Width (inches) Width (mm) Colours Available Spools in length (metres)

V25HA Hook 1” 25 Black, White 25

V25LA Loop 1” 25 Black, White 25

V50HA Hook 2” 50 Black, White 25

V50LA Loop 2” 50 Black, White 25

Plastic Fasteners – Hook & Loop

Pla

stic

Fas

tene

rs -

Ho

ok

& L

oo

p

130

Accessories


Eq

uest

rian

Fit

ting

s

Equestrian FittingsSNAP HOOKS – ROUND SWIVEL

Item Code

Description

BUSN15R 16mm (5/8 inch)

BUSN19R 19mm (¾ inch)

BUSN25R 25mm (1 inch)

SNAP HOOKS – SQUARE SWIVEL

Item Code

Description

BUSN19 19mm (¾ inch)

BUSN25 25mm (1 inch)

SNAP HOOK SMALL

Item Code

Description

BUSNS12 Small Snap Hook with 12mm Swivel

BUSN19S Small Snap Hook with 19mm Swivel

SNAP HOOK – EXTRA SMALL

Item Code

Description

BUSN-D230BR16mm (5/8 inch)

-Brass only

DOUBLE END SNAP HOOKS

Item Code

Description

BUSND90 90mm Long (3 ½ inch)

DOUBLE END SNAP HOOKS

Item Code

Description

BUJH19 19mm (¾ inch)

BUJH25 25mm (1 inch)

131

Accessories


Eq

uest

rian

Fit

ting

s

Equestrian FittingsBULL SNAP ROUND EYE

Item Code

Description

BUSNBE22 22mm (7/8inch) x 100mm (4 inch)

PANIC SNAP ROUND EYE

Item Code

Description

BUPANIC 25mm (1 inch) x 108mm (4 1⁄4 inch)

SOLID BRASS SNAP HOOK WITH SWIVEL

Item Code

Description

BUSNBR32 32mm (1 1⁄4 inch) x 115mm (4 1⁄2 inch)

GEAR BUCKLE - CROCODILE CLIP

Item Code

Description

BUGB25 25mm ( 1 inch)

METAL CAMLOC

Item Code

Description

CAM25B

CAM25SIL

CAM25SS

25mm (1 inch) Available in Black Enamel, Nickel & Stainless Steel Finishes

CAM50B 50mm (2 inch) Available in Black Enamel & Nickel Finishes Only

CARABINA HOOK

Item Code

Description

BUCAR60 60mm (2 1/3 inch) x 25mm (1 inch)

BUCAR80 80mm (3 1/10 inch) x 25mm (1 inch)

CAM25SILCAM25B

132

Accessories


Eq

uest

rian

Fit

ting

s

Equestrian FittingsHOBBLE BUCKLES

Item Code

Description

BUHB19 19mm (3⁄4 inch)

BUHB25 25mm (1 inch)

SKATE BUCKLES

Item Code

Description

BUSK16 16mm

BUSK19 19mm (¾ inch)

BUSK25 25mm (1 inch)

BUSK32 32mm

HARNESS BUCKLES

Item Code

Description

BUHA25 25mm (1 inch)

BUHA32 32mm (1 1⁄4 inch)

BUHA38 38mm (1 1⁄2 inch)

BUHA50 50mm (2 inch)

LOOPED BARRED GIRTH BUCKLE

Item Code

Description

BUGBSS25 25mm (1 inch)

WEST END BUCKLE - BRASS

Item Code

Description

BUWE25 25mm (1 inch) (With Stainless Steel Tongue)

BUWE32 32mm (1 1⁄4 inch)

133

Accessories


Eq

uest

rian

Fit

ting

s

Equestrian Fittings2 BAR BUCKLES - BRASS

Item Code

Description

BU2BB1919mm (¾ inch)

Solid Brass Body with Stainless Steel Tongue

BU2BB2525mm (1 inch)

Solid Brass Body with Stainless Steel Tongue

BU2BB25P25mm (1 inch)

Steel-Brass Plated Body

BU2BB25N25mm (1 inch)

Steel-Nickel Plated Body

SWAGE BUCKLES - BRASS

Item Code

Description

BUSW16 16mm (5/8 inch)

BUSW19 19mm (¾ inch)

BUSW22 22mm (7/8 inch)

BUSW25 25mm (1 inch)

HALTER SQUARE - BRASS

Item Code

Description

BUHS25 25mm (1 inch)

EZI CLIP® BY WILSHIRE SADDLERY

After 35 years of rug manufacture and repair, John Wilshire believes the weakest link of almost all rugs is the snap hook attached to the leg strap.

In many cases, some of the best made rugs are let down by the breakage of a cheap snap!

After 5 years of testing John has finally come up with what he believes is the ultimate snap – the EZI CLIP.®

The product has no moving parts and is not affected by the weather, including mud and water.

The nylon EZI CLIP® is almost unbreakable and will not catch in tails or wire fences.

Item Code

Size in mm Description In Bags of

EZICLIP-BLK 25 Plastic Moulded Ezi Clip (Black) includes small and large clips as a pair 50 pair

EZICLIP 25Plastic Moulded Ezi Clip (White)

includes small and large clips as a pair50 pair

134

Accessories


Eq

uest

rian

Fit

ting

s

Equestrian FittingsBELT KEEPER

Item Code

Description

BUBK19 19mm (3⁄4 inch)

BUBK25 25mm (1 inch)

BUB50K 50mm (2 inch)

TRI GLIDES - STEEL

Item Code

Description

BUTG19 19mm (3⁄4 inch)

BUTG25 25mm (1 inch)

BUTG50 50mm (2 inch)

TRI GLIDES - STAINLESS STEEL

Item Code

Description

BUTG25SS25mm (1 inch)

SURCINGLES

Item Code

Description

BUSUR50M Male 50mm (2 inch)

BUSUR50F Female 50mm (2 inch)

BUTG50 Tri Glide 50mm (2 inch)

135

Accessories


Eq

uest

rian

Fit

ting

s

Equestrian FittingsD-RINGS - STEEL NICKEL PLATED

Item Code Size

BUD20E5SN ¾ inch (20mm x 5mm wire)

BUD25E4SN 1 inch (25mm x 4mm wire)


BUD32E5SN 1¼ inch (32mm x 5mm wire)

BUD38E6SN 1½ inch (38mm x 6mm wire)


O-RINGS - STEEL NICKEL PLATED

Item Code Size

BUO25E5SN 1 inch (25mm x 5mm wire)

BUO32E5SN 1¼ inch (32mm x 5mm wire)

BUO38E6SN 1½ inch (38mm x 6mm wire)

BUO50E7SN 2 inch (50mm x 7mm wire)

BUO605SN 2 ½ inch (60mm x 5mm wire)

BUO70E5SN 2¾ inch (70mm x 5mm wire)

O-RINGS - SOLID BRASS

Item Code

Description

BUOBR32 32mm (1⁄4 inch) x 6mm

BUOBR50 50mm (2 inch) x 7mm

38 x 6mm

50 x 7mm 20 x 5mm

25 x 6mm

25 x 4mm

50 x 7mm

25 x 5mm

32 x 5mm

38 x 6mm 70 x 5mm

136

Accessories


Eq

uest

rian

Fit

ting

s

Equestrian FittingsLEATHER STRAPPING WAXED - 3MM THICK

Item Code Size Description

LESTRAP/18 450mm (18 inch) x 25mm (1 inch) Leather Strap

LEBB/19 19mm (¾ inch) Chest - Buckle & Billet Set

LEBB/25 25mm (1 inch) Chest - Buckle & Billet Set

LESQ/S 70mm x 70mm Leather Square - Single Hole

LESQ/D 70 x 105mm Leather Square - Double Hole

PVC STRAPPING

PVC Straps are made from heavy duty conveyor belting and are available in Forest Green or Sand colours.

Item Code Size Description

LEP-S18 450mm (18 inch) x 25mm (1 inch) PVC Strap

LEP-BU25 235mm (9 inch) x 25mm (1 inch) Chest Strap (Buckle)

LEP-BI25 160mm (7 inch) x 25mm (1 inch) Chest Strap (Billet)

LEP-SQS 100mm(4 inch) x 75mm (3 inch) D Plate - Single Slot

LEP-SQD 110mm (4 1⁄2 inch)x 75mm (3 inch) Square Plate - Double Slot

ENGLISH GIRTH ELASTIC

The original English Elastic - available in Black or White.

Item Code Size

W-EGE25 25mm(1 inch)

W-EGE32 32mm (1 1⁄4 inch)

W-EGE50 50mm (2 inch)

Leather Square – Single Hole

Leather Square – Double Hole

25mm Buckle & Billet Set

20mm Buckle & Billet Set

Leather Strap

137

Accessories


Mar

ine

Acc

esso

ries

Marine AccessoriesTUBE ENDS

Item Code

DescriptionTube Size

in mm

SM101 Tube End 25mm (Blk) Slides inside 25mm x 1.6mm tubing 25 x 1.6

SM102 Tube End 25mm (White) Slides inside 25mm x 1.6mm tubing 25 x 1.6

SM103 Tube End 25mm (Black) Slides inside 25mm x 3mm tubing 25 x 3

SM104 Tube End 25mm (White) Slides inside 25mm x 3mm tubing 25 x 3

SM105 Tube End 20mm (Black) Slides inside 20mm x 1.6mm tubing 20 x 1.6

SM106 Tube End 20mm (White) Slides inside 20mm x 1.6mm tubing 20 x 1.6

BOW KNUCKLES

Item Code


in mm

SM201

Bow Knuckles 25mm (Black)

Clamps around 25mm tubing.

Includes stainless steel 1⁄4 inch (6mm) diameter screw & nut

25

SM202

Bow Knuckles 25mm (White)



25

SM203

Bow Knuckles 20mm (Black)



20

SM204

Bow Knuckles 20mm (White)



20

THUMBSCREWS

Item Code

Description

SM401Thumbscrew (Black)

Used where a frame is continuously loosened or removed. Stainless steel 1⁄4 inch (6mm) screw

SM402Thumbscrew (White)


#7XLThumbscrew (Black) Extra Long Thread


138

Accessories


Mar

ine

Acc

esso

ries

Marine AccessoriesDECKMOUNTS – CURVED

Item Code

Description

SM301

Deckmount Curved (Black)

This unit has an angled base to suit angled decks.


SM302

Deckmount Curved (White)

This unit has an angled base to suit angled decks.


DECKMOUNTS – FLAT – EXTENDED

Item Code

Description

SM307

Deckmount Flat (Black)

This unit has a flat base to suit flat decks.


SM308

Deckmount Flat (White)

This unit has a flat base to suit flat decks.


BUNJI KNOB

Item Code


SM501

Bunji Knob (Black)

Suits up to 8mm rope/shock cord.

Internal fixing hole suits up to size 6 Rivet

100

SM502

Bunji Knob (White)

Suits up to 8mm rope/shock cord.

Internal fixing hole suits up to size 6 Rivet

100

139

Accessories


Mar

ine

Acc

esso

ries

Marine AccessoriesSIDE MOUNTS

Item Code

Description

SM305

Side Mount (Black)

Used where a vertical bow mount is required.


SM306

Side Mount (White)

Used where a vertical bow mount is required.


TUBE END SLIDE

Item Code


in mm

SM115

Tube End Slide (Black)

Slides inside 20mm x 1.6mm tube

Used where a movable fitting position is required

20 x 1.6

SM116

Tube End Slide (White)

Slides inside 20mm x 1.6mm tube


20 x 1.6

SM113

Tube End Slide (Black)

Slides inside 25mm x 3mm tube


25 x 3

SM114

Tube End Slide (White)

Slides inside 25mm x 3mm tube


25 x 3

WEBBING BUCKLE

Item Code

Description

SM701Buckle (Black)

Suits up to 27mm wide webbing

SM702Buckle (White)


WEBBING D-BUCKLE

Item Code

Description

SM703D-Buckle (Black)


SM704D-Buckle (White)


140

Accessories


Mar

ine

Acc

esso

ries

Marine AccessoriesTUBE END T

Item Code


in mm

SM109

Tube End T (Black)

Includes stainless steel 1⁄4 inch (6mm) diameter nut

Slides Inside 25mm x 1.6mm tubing

25 x 1.6

SM110

Tube End T (White)



25 x 1.6

SM111

Tube End T (Black)


Slides Inside 25mm x 3mm tubing

25 x 3

SM112

Tube End T (White)


Slides Inside 25mm x 3mm tubing

25 x 3

TUBE END CLAMP

Item Code


in mm

SM107

Tube End Clamp (Black)

Clamps on to 20mm tubing for bracing purposes.


20 x 1.6

BOAT BUNGS

Item Code

Description

PK1003Bung Plug – Fine Thread

Bung Plugs with coloured washer to fit most 16mm bases on the market

PK1002Bung Plug – Coarse Thread

Bung Plugs with coloured washer to fit most 16mm bases on the market

PK1004Bung Plug – Complete Unit with Coarse Thread

Nylon drainage bung 16mm coarse thread bung with washer and base

141

Accessories


Mar

ine

Acc

esso

ries

Marine AccessoriesSTAINLESS STEEL TUBE ENDS

Item Code


in mm

7163 Stainless Steel Tube End Cap with Eye 19



G641S Stainless Steel Tube with Single Grub Screw 32

70076 Stainless Steel End Cap with Double Grub Screws 32

STAINLESS STEEL BOW KNUCKLE

Item Code


in mm

7171 Stainless Steel Bow Knuckle with Bolt 19



G640S Stainless Steel Bow Knuckle Slide with Single Grub Scew 32

70083 Stainless Steel Bow Knuckle Slide with Double Grub Scews 32

WINGED BOW KNUCKLES

Item Code


in mm

G820S Stainless Steel Separating Bow Knuckle 22




142

Accessories


Fram

e K

it &

Hea

vy D

uty

Can

op

y Tr

ack

Frame Kit & Heavy Duty Canopy TrackUNIVERSAL BOAT TOP FRAME KITS

• Ready to assemble kit form.• Easy to use, fits boats to 2.4m/96 inches wide.• Manufactured from marine grade aluminum tube

and die cast hardware.• No bending tools required.• Can ship UPS.

• Packaged 1 boat set per box with hardware. Boxes can be shipped by UPS. Made with 22mm/ 7⁄8 inch O.D. x 0.058” wall, 6063 T832 hard drawn marine aluminum tubing with a brite anodized finish and joined together with inside sleeves. The radius of the bends are 152mm/6 inch I.D.

UNIVERSAL BOAT TOP FRAME KITS

Kit contains: • 4 x die cast eye ends. • 2 x die cast jaw slides. • 2 x die cast hinges. • 2 x bow assembly pre-formed 22mm/ 7⁄8 inch aluminum

tubing.


G522A 2 Bow Aluminum Frame Kit

BIMINI 3 BOW FRAME KIT

Kit contains: • 6 x die cast eye ends. • 4 x die cast jaw slides. • 2 x die cast hinges. • 3 x bow assembly pre-formed 22mm/ 7⁄8 inch aluminum

tubing.

HEAVY DUTY CANOPY TRACK SYSTEM

• Top quality way to solve the problem of improving canopy or enclosure.

• This unique system is easily fitted and adds extra functionality to most modern styles of canopy or enclosure.

• 25mm/1 inch H.D. track system.• Stainless steel fittings pre-assembled to car.• Extruded aluminum track & car.• Car secured by spring loaded stops.


G710 Car Includes S.S. Universal Deck Hinge Each

G712 1.2m/48" Aluminum Track Each

G718 1.8m/71" Aluminum Track Each

G713 Track End Stops - Sold in Pairs Pair

DUO TRACK SYSTEM

• Quick release adjustment.• Manufactured from 316 stainless

steel.• Ultra low profile design with

positive locking mechanism.• Easily operated by hand or foot.• Ideal for mounting biminis on

center cockpits.


G722S Duo Track - 1.8 Meters Long Each

G723END Duo Track Stainless Steel End Stop Each

G721S Duo Track Car with Low Profile Deck Hinge (G645S) Each

G721STOP Duo Track Car Locking Stop Each

Simply cut to size

2438mm/96" wide

1524mm/60"

2438mm/96" wide

1524mm/60"

1016mm/40"1524mm/60"

G721S

G722SG723END

143

Accessories


Stai

nles

s St

eel B

oat

To

p F

itti

ngs

Stainless Steel Boat Top FittingsDECK HINGE FITTINGS - SCREW PIN

• Die cast type 316 stainless steel.• Mirror polished finish.


7089 Flat Hinge with Screw Pin 50

7091 Angle Hinge with Screw Pin 50

7090 Concave Hinge with Screw Pin 50

DECK HINGE FITTINGS - REMOVABLE PIN

• Die cast type 316 stainless steel.

• Mirror polished finish.


7089RP Flat Hinge with Removable Drop Nose Pin 50

G625SQP Flat Hinge with Quick Release Pin 50

7091RP Angle Hinge with Removable Drop Nose Pin 50

G628SQP Angle Hinge with Quick Release Pin 50

G651S Concave Hinge with Removable Drop Nose Pin 50

REMOVABLE PIN




G627PIN Drop Nose Pin 6.4mm/ 1⁄4 " O.D. 50

G625PIN Quick Release Pin 6.4mm/ 1⁄4 " O.D. with S.S. Ring 50

G637PIN Drop Nose Pin 6.4mm/ 1⁄4 " O.D. with S.S. Ring 50

SIDE MOUNT FITTING



• Accepts all sizes of eye end.


G624S 4 Hole Side Mount 8.0mm / 5/16" Bolt 50

7096 4 Hole Side Mount 6.4mm / 1⁄4" Bolt 50

7092 2 Hole Side Mount 6.4mm / 1⁄4" Bolt 50

LANYARD

• Stainless steel.


G625LAN Stainless Steel Wire - 152mm/6" 50

G634LT 6.4mm/ 1⁄4" I.D. Pin, 152mm/6" S.S. Wire with Tab 50

G745S Quick Release 6.35mm/ 1⁄4" x 25mm/1" 50

FOOTMAN LOOP - WEB BRIDGE

• Stainless steel.

Part No. Description Width (mm/in) Pack Qty

G205S Stainless Steel 25 / 1 50

G209S Stainless Steel 25 / 1 50

7089 70907091

7089RP

C625PIN

G627PIN

G637PIN

7092

7096

G625LAN

G634LTG745S

G205SG209S

144

Accessories


Stai

nles

s St

eel B

oat

To

p F

itti

ngs

Stainless Steel Boat Top FittingsUNIVERSAL DECK HINGES - STAINLESS STEEL

Universal deck hinge compensates for different angles of decks and coamings. Made from mirror polished stainless steel, even vertical surfaces can be accommodated.




• Compensates for different deck and coaming angles including vertical surfaces.


G615S Universal Deck Hinge with Screw 50

LOW PROFILE DECK HINGE

• Made in 316 stainless steel.

• Use G646S for larger angles.


G645S Angle Deck Hinge 50

G646S Straight Universal Deck Hinge 50

BALL SWIVEL WITH QUICK RELEASE DECK MOUNT & EYE END

• Manufactured from 316 stainless steel.

• Greater range of motion.

• Base screws to the deck.

• Removing quick pin allows hinge to slide off the base.

• Double set screws.


G771S 22mm/ 7⁄8 " Ball Swivel Deck Hinge 50

G731S 25mm/1" Ball Swivel Deck Hinge 50

G645S G646S

145

Accessories


Stai

nles

s St

eel B

oat

To

p F

itti

ngs

Stainless Steel Boat Top FittingsHD FOLDING DECK HINGE

• Hinge system compensates for different angles of deck and coamings without the need for wedges.

• Folds flat when canopy is removed preventing snagging and injury.

• Manufactured from type 316 stainless steel.

• Use with G611S, G621S, G631S and G641S.


G607S Stainless Steel HD Folding Deck Hinge 50

UNIVERSAL FLAT DECK HINGE


• Deck hinge swivels 180°.


G692S Flat Universal Deck Hinge 50

QUICK RELEASE DECK MOUNT

• Spring-loaded release button ejects eye end for almost instant frame removal.

• Stylish and unique design.

• Manufactured from type 316 stainless steel.

• Use with G611S, G621S, G631S and G641S.


G605S Quick Release Deck Mount 24

G606S 22mm / 7/8 " Quick Release Side Mount 50

G608S 25mm/1" Quick Release Side Mount 50

G605SHNT Shim - Natural 50

G605SHBK Shim - Black 50

HEAVY DUTY QUICK RELEASE DECK MOUNT

• Heavy duty design & construction.

• Allows full 360 degree rotation.

• Three position lock.

• Accepts extra wide tab eye ends.

• Secure three point mounting.


G604S 316 Stainless Steel 1

G606S

G605S

G605SHWT G605SHBK

146

Accessories


Stai

nles

s St

eel B

oat

To

p F

itti

ngs

Stainless Steel Boat Top FittingsEYE ENDS



• G631SHD & G641SHD have 2 set screws.

• 6.35mm/1⁄4 “ hole in eye.


7163 Eye End for 19mm/ 3⁄4" Tube 50

7085 Eye End for 22mm/ 7/8" Tube 50

7086 Eye End for 25mm/1" Tube 50

G631SHD Heavy Duty Eye End for 25mm/1" Tube with 2 Set Screws 50

70076 Heavy Duty Eye End for 32mm/11⁄4" Tube with 2 Set Screws 50

BALL SWIVEL JAW SLIDE AND EYE ENDS

• Increase frame versatility.

• Allows full movement range.


• Double set screws.


G770S 22mm/ 7/8 " Ball Swivel Jaw 50

G730S 25mm/1" Ball Swivel Jaw 50

JAW SLIDES/EYE ENDS



• G630SHD & G640SHD have 2 set screws.


7171 Jaw Slide for 19mm/ 3⁄4" Tube 50

7083 Jaw Slide for 22mm/ 7/8" Tube 50

7084 Jaw Slide for 25mm/1" Tube 50

G630SHD Heavy Duty Jaw Slide for 25mm/1" Tube with 2 Set Screws 50

70083 Heavy Duty Jaw Slide for 32mm/11⁄4" Tube with 2 Set Screws 50

DOUBLE JAW SLIDE WITH SWIVEL HINGE


• Allows 2 eye ends to be connected to the same jaw.



G687S 22mm/ 7⁄8 " Double Jaw with Swivel Hinge 50

G697S 25mm/1" Double Jaw with Swivel Hinge 50

70076

G631SHD

71637083

G630S

G640SHD

147

Accessories


Stai

nles

s St

eel B

oat

To

p F

itti

ngs

Stainless Steel Boat Top FittingsSPLIT JAWSLIDE/RAIL FITTING

Mounts without the need to disassemble the rail. Ideal for use on rails that are welded together. Simply slide the two halves together on either side of the rail and they interlock. The fitting fastens easily with a single nut and bolt to the rail in the exact position you desire.

• Package consists of one rail fitting and a stainless steel screw and nut.

• Type 316 stainless steel.

• Order G625PIN, G627PIN or G830SN to connect eye end.


G820S 22mm/ 7/8 " Outside Diameter 50

G830S 25mm/1 " Outside Diameter 50

G840S 31mm/1 1⁄4 " Outside Diameter 50

SIDE MOUNT JAW SLIDE

• Allows outboard or inboard mounts of Gemlock struts.

• Outboard mount allows the Gemlock strut to act as grab rail.

• Grab rail stands off to allow bimini to fold flat.


G635S 25mm/1" Stainless Steel

BLACK NYLON BOAT TOP FITTINGS

High strength black nylon fittings have excellent resistance to UV. Works with either stainless steel or aluminum tubing.


G621BK For Use with Tube Outside Diameter 22mm/ 7/8 " 50

G620BK For Use with Tube Outside Diameter 22mm/ 7/8 " 50

G622BK Flat Fitting with Screw Pin 50

See Shackleton Fittings

G621BK

G620BKG622BK

148

Accessories


Stai

nles

s St

eel B

oat

To

p F

itti

ngs

Stainless Steel Boat Top FittingsFRAME TUBE HINGE WITH QUICK RELEASE LOCKING PIN

• Heavy duty design and construction.

• Allows frame or strut to fold.

• Quick release locking pin, locks only when straight.


Part No. Description Tube Size (mm/in)

G744S Heavy Duty Stainless Steel Tube Hinge 25 / 1

G747S Heavy Duty Stainless Steel Tube Hinge 22 / 7/8

STAINLESS STEEL SPRING BALL

• All stainless steel designed for tubing 19mm/ 3⁄4 inch to 32mm/11⁄4 inch inside diameter.


G757 Stainless Steel Snap - Spring Ball - Solid Head 100

G758 Stainless Steel Snap - Spring Ball - Hollow Head 100

STAINLESS STEEL SET SCREWS

• Spare stainless steel set screws for eye ends or jawslides.



G620SS 6.4mm/ 1⁄4 " – 20 Stainless Steel Set Screws 10

G622SS Spare Screw for G622S, G623S, G626S, G615S etc. 10

G830SN Hex Head Screw & Nut 10

GEMINI SLIDING SIDE MOUNT

• Allows outboard or inboard mounts of Gemlock struts.

• Outboard mount allows the Gemlock strut to act as grab rail.

• Grab rail stands off to allow bimini to fold flat.


G633S 22mm/ 7/8 " Stainless Steel 100

G635S 25mm/1" Stainless Steel 100

G757 G758

G620SS G622SS G830SN

Open

Closed

149

Accessories


Gem

lock

Co

llap

sib

le S

trut

& H

ing

e

Gemlock Collapsible Strut & Hinge

GEMLOCK PRE-MADE STRUT WITH HINGE

• Completely assembled struts with stainless steel hinges, either 22mm/ 7/8 inch or 25mm/1 inch tubing, locking sleeve and spring balls.

• Uses: folding dodger frames (DropTop™ style), spreader bars on biminis (strapless biminis), stowable dinettes and chart tables, cantilever supports for swim platforms and drop seats, support struts for davits and towers.

Part No. Description Tube Size (mm/in) Length (mm/in)

G750SSET/2 Adjustable Strut 22 / 7/8 600 / 24

G750SSET/4 Adjustable Strut 22 / 7/8 1200 / 48

G751SSET/2 Adjustable Strut 25 / 1 600 / 24

G751SSET/4 Adjustable Strut 25 / 1 1200 / 48

Note: Single strut – 2 struts required to make a folding top.

GEMLOCK COLLAPSIBLE HINGE

• The Gemini™ hinge (patent pending) and strut assembly provides a simple way to build collapsible supports and folding frames with no disassembly of frame parts. To fold the strut, slide the locking sleeve and pop the hinge.

• Can be fitted to existing frames.

• Unique link hinge design allows strut to fold completely flat.

• External sleeve locks joint and provides full working strength to the strut, protecting the hinge from loads.

• Spring balls lock sleeve in place to prevent accidental folding.

• A complete installation for each side will require 1 hinge, 1 locking sleeve, 2 snap buttons and 2 set screws.

• Full installation instructions sheet available upon request.

• Uses: spray hoods, biminis and tables.

GEMLOCK HINGE & SLEEVE

Part No. DescriptionTube Diameter

(mm/in)Wall Thickness

(mm/in)

G750S S.S. Gemini Hinge 22 / 7/8 1.6 / 0.065

G751S S.S. Gemini Hinge 25 / 1 1.6 / 0.065

G760 S.S. Locking Sleeve 22 / 7/8 1.6 / 0.065

G761 S.S. Locking Sleeve 25 / 1 1.6 / 0.065

G761/10 S.S. Locking Sleeve 25 / 1 1.6 / 0.065

GEMLOCK STAINLESS TUBE HINGE KIT

• All components required to make a pair of collapsible supports and folding frames.

• Easy to purchase all parts to make two complete hinges in a single kit.

• Each kit contains: 2 x S.S. hinges, 2 x S.S. locking sleeves, 4 x S.S. spring balls, 4 x S.S. set screws.

• Can make 2 struts for folding top.

Part No. Description Tube Size (mm/in)

G750SSET Kit - Makes 2 Hinges 22 / 7⁄8

G751SSET Kit - Makes 2 Hinges 25 / 1

Closed

Open

G760

G750S Open

G750S Closed

150

Accessories


Tub

e B

end

ers

Tube BendersBENDARC TUBE BENDER

• Bendarc Quick-Switch - Gives strong bends with smooth, rounded corners.

• Designed for wall or bench mounting and easy pull down use, Bendarc can bend 152mm/6 inch radius to 300mm/12 inch radius, depending on which dies are purchased.

• Easy, pull-down use. Wall mounting allows your body weight to help.

• Quick and easy to switch sizes.

• Constructed of boiler plate steel with bearing supported roller and powerful 998kg/2200 lb. clamp.

• Rollers are high density polymer for mar resistant contact with fine tubing finishes.

• Other size radius dies, rollers are available.


G635SBend 25mm/1” Tube to 203mm/8” Radius

Bend 25mm/1” Tube to 250mm/10” Radius

CROWNARC TUBE BENDER

• Crownarc - The only crowner with gear drive. • Mounted on the wall, a table or on the side or rear of a

truck, Crownarc puts a crown onto tubing. • Bends 19, 22 & 25mm / 3⁄4, 7/8 & 1 inch outside diameter

tubing using the same dies.• Dies and rollers are mounted on a backplate of boiler plate

steel.• Rollers are high density polymer.• The center roller is fully adjustable.


C998 19, 22 & 25mm/ 3⁄4 , 7⁄8 & 1" Tubing

ADJUSTABLE EYE ENDS

• Designed to tighten canvas on bimini tops.• A pair can adjust 2 inches in length.• One pair = one right and one left thread.• Requires one pair per strut.


G845S 22mm / 7/8 " Tube Adjuster Pair

G846S 25mm /1" Tube Adjuster Pair

Note: Two pairs required to make a set.

CANVAS CLIP

• Helps to hold fabric on frame while patterning.• One end can be used on 7/8“, the other is for 1”.


G380 Canvas Clip 50

Quick-Switch

1"1"

1" x 6" radius

7/8" x 8" radius

7/8"

1 - Insert the uncrowned bow

2 - Crank it Through

151

Accessories


Tub

e &

Fra

me

Acc

esso

ries

Tube & Frame AccessoriesSTAINLESS STEEL TUBING

• Tubing is sold in 7.3m / 24 foot lengths only, and must ship by common carrier.

Part No. Outside Tube Diameter (mm/in) Wall Thickness (mm/in)

G500S 22 / 7/8 1.2 / 0.049

G501S 25 / 1 1.2 / 0.049

G503S 22 / 7/8 1.7 / 0.065

G505S 25 / 1 1.7 / 0.065

DRILL STEADY

Designed to clamp onto frames or tubing without disassembling frame.

• Swing over design.

• Bronze cast body.

• Requires 9/64“ cobalt drill bit to set No.8 screws.


C899 Drill Steady

SUNBLOCKER CLIP

Sunblocker is a self insulated protective clip which eliminates contact between your metal tubular top frame and the clear plastic windows. Two or three Sunblocker clips on metal frame tubing can give maximum protection against destruction of clear plastic windows, by reducing singeing, scorching and heat cracking.• Marine gray color.• Designed cooling air vents.• All rounded corners eliminates abrasion.

Part No. DescriptionPack Qty

G638 Single For Use with Tube Outside Diameter 22mm / 7/8 " 50

G639 Single For Use with Tube Outside Diameter 25.4mm / 1" 50

G738 Twin For Use with Tube Outside Diameter 22mm / 7/8 " 50

POLYESTER LACING CORD

• Solid braid are made from continuous filament, high tenacity yarns. Lockstitch construction offers excellent abrasion resistance, maintains uniform diameter and are superior to Diamond braid.

• Resists UV rays. Best for marine and outdoor use.

• Will not harden.

• Use for lacing line for top, side curtains, tie downs, netting and marine covers.

Part No. Description Diameter (mm/in) Reel Length (mm/in)

E350P Size 4 White 3.0 / 1/8 305 / 1,000

E350PBK Size 4 Black 3.0 / 1/8 305 / 1,000

E358P Size 5 White 3.7 / 5/32 305 / 1,000

E352P Size 6 White 4.8 / 3/16 305 / 1,000

E352PBK Size 6 Black 4.8 / 3/16 305 / 1,000

E354P Size 8 White 6.3 / 1⁄4 305 / 1,000

SUN SOX TO PROTECT PLASTIC WINDOWS

Windows resting against hot tube framing can be scorched, turn colors and be destroyed. New SUN Sox offer a simple and inexpensive protection. Made from a non-woven poly blend of fibers with a velcro strip on one edge, SUN SOX simply wraps around tubing and secures to itself. 6 foot lengths can be cut to match tube size and come in six attractive colors.

• Simple do it yourself installation offers easy on easy off or leave year round.

AVAILABLE COLOURS

Gray Blue Black

Green Beige Dubonnet

Part No. Colour Length (m/ft)

LS401GY Gray 1.8 / 6

LS401BU Blue 1.8 / 6

LS401BK Black 1.8 / 6

LS401GR Green 1.8 / 6

LS401TN Beige 1.8 / 6

LS401DB Dubonnet 1.8 / 6

G638 G738

152

Accessories


Gra

b R

ail &

Fit

ting

s

Grab Rail & FittingsSTAINLESS STEEL GRAB RAIL WITH STUDS


• Heavy duty polished construction.

• Stainless steel bolt with 1⁄4 – 20 threads x 1 3⁄4 “ long.

Part No. DescriptionPack Qty

G380/18 18" (457mm) Stainless Steel Grab Rail 10

G380/24 24" (610mm) Stainless Steel Grab Rail 10

J-HOOK

• Stainless steel hook to fit over 1 1/8“ (29mm) gunwale.

• Requires no fitting on deck.

• 3⁄4“ (19mm) wide x 2 1⁄2“ (64mm) long.


J858S Stainless Steel J-Hook

POP RIVETS

• Use washer to help insulate metals.

• Sold in full packs of 100 only.

Part No. Diameter (mm/in) Length (mm/in) Finish

G171FW 4 / 3⁄16 - / - Plastic Washer

D390 3 / 1⁄8 6 – 8 / 1⁄4 – 5/16 Aluminum

D392 4 / 3⁄16 6 – 10 / 1⁄4 – 3/8 Aluminium

D392S 4 / 3⁄16 6 – 10 / 1⁄4 – 3/8 Stainless Steel

SPEEDY RIVETS

• Use with B401 Hooks.• Tap the two parts together with a hammer until they

connect firmly.• Only order by full pack - 100 per pack.

Part No. FinishPack Qty

D050N Nickel Plated Brass 100

SCREWS - STAINLESS STEEL

• Use washer to help insulate metals.

• Sold in full packs of 100 only.

Part No. Size (mm/in) Style Head

D350 No. 4 x 3⁄8 (10) Self Tapping Pan



D355 No. 6 x 1⁄2 (12) Self Tapping Flat



D373 No. 6 x 3⁄4 (19) Self Tapping Oval

153

Accessories


Tie

Do

wn

& L

acin

g F

itti

ngs

Tie Down & Lacing FittingsSEW-ON COVER HOOKS & EYELETS - PLASTIC

• Injection moulded in nylon.

• Sew through plastic with straight stitch sewing machine.

• Can be used alone, or together.


HA069BK Hook Black 100

HA069WT Hook White 100

HA068BK Eyelet Black 100

HA068WT Eyelet White 100

WIRE COVER HOOKS & BACKPLATE

Ideal method for a simple lacing line run between grommets and cover hook.• Hand sew or use D050N speedy rivets (see below) or D383

or D384 rivets.• Suitable for up to 9.5mm/ 3⁄8 inch shock cord.• Use SS washers as back plates.

Part No. Description Material Pack Qty

HB401B Hook Brass 100

HB401S Hook Stainless Steel 100

RIVET-ON COVER HOOK - PLASTIC

• Injection moulded in nylon.

• Use D337 rivets or D383 rivets.

• Suitable for max 6.4mm/ 1⁄4 inch shockcord.

Part No. Outside Tube Diameter (mm/in) Pack Qty

A071 White 100

SHOCK CORD COVER CLIP

• Used with a lacing knob or other cord cover clip for a fast and simple tie-down.

• Does not require tool to set.• Now easier attaching system.

Part No.Overall Length

(mm/in)Colour Pack Qty

G040BK 86 / 3 3/8 Black 50

G040WT 86 / 3 3/8 White 50

SHOCK CORD LACING KNOB

Used with a cord cover clip for a fast and simple tie-down.• Attaches with a screw.• See Shackleton.

Part No.Use with Cord Diameter (mm/

in)

Kob Diameter (mm/in)

Colour Pack Qty

G045BK 5 / 3/16 18 / 11/16 Black 50

G045WT 5 / 3/16 18 / 11/16 White 50

A068WT A069WT

B401B

G040WT

G040BK

154

Accessories


Aw

ning

Tap

es

Awning TapesKEDER TAPE

• Durable woven polyester tape welded to a polyethylene core.

• Sold in 100m/328’ reels.

• Cut yardage available at a surcharge.

• Available in two sizes.

• White or Black.

• Split tail version also available.

• See page 85

Part No. Colour Diameter (mm) Tape Width (mm/in) Use With

L575 White 7.5 20 / 3⁄4 G510

L575T White 7.5 25 / 1 G510

L575BK Black 7.5 20 / 3⁄4 G510

L585 White 8.5 20 / 3⁄4 G520/G530

L585LT White 8.5 20 / 3⁄4 G520/G530

L585BK Black 8.5 20 / 3⁄4 G520/G530

POLYESTER AWNING ROPE

• Supplied on 76m/250’ reels.

• Tape weave 280gsm/6.5oz.

• Cut yardage available at a surcharge.

• New Product - LS005

Part No.Diameter (mm/in)

Tape Width (mm/in)

Tape Weave (gsm/smoz)

Use

LS005 5.5 / 7/32 24 / 15/16 278 / 6.5 G535WT/20

LS002 6.0 / 1⁄4 20 / 13/16 278 / 6.5 G540

LS001 8.0 / 5/16 20 / 3⁄4 278 / 6.5 G530

VINYL EXTRUDED AWNING ROPE

• Awning rope is supplied on 76m/250 foot reels.• Not for Flex-A-Rail.• Cut lengths will be surcharged.

Part No. Diameter (mm/in) Tape Width (mm/in) Colour

CantrackI 8.35 20 White

CantrackIS 5.25 15 White

3M VHB ATTACHMENT TAPE

• High performance acrylic adhesive.• Medium density white acrylic foam tape.• Adhesive on both sides with red release liner.• Use: Attaching automotive and marine trim, awning track,

flex a rail.

Part No. Width (mm/in) Roll Length (m/yd) Case Qty

G040BK 86 / 3 3/8 Black 50

G040WT 86 / 3 3/8 White 50

KEDER TRACK SLIDE

• Allows quick and easy installation to many awning tracks.

• Designed to suit both aluminium and vinyl track (not Flex-a-Rail).

• Potentially removes the need for awning ropes.

• Ideal for making curtains that open and close.

Part No. Colour Pack Qty

A091WT White 100

ALUMINIUM AWNING TRACK

• Bright polished aluminum awning track.• Compatible with most BI awning ropes and Keder tapes.• Use pan head screws to install.

Part No. ColorInternal Diameter

(mm/in)Track Length (mm/ft)

G520 Anodised Aluminum 9 / 3/8 4850 / 16

G520-8 Anodised Aluminum 9 / 3/8 2425 / 8

Tape WidthL575T/L585T

Tape WidthL575/L585

TapeWidth

Tape Width

CAUTION

WARNING: Always test adhesive bond strength for your material and application.

155

Accessories


Aw

ning

Tra

ck

Awning TrackCOVER TRAX SYSTEM

Unique new low profile awning rail system with dacron awning rope and sliding screw cover panel to hide attaching screws.• Premium grade extruded PVC with UV inhibitors.• Sleek and ultra low profile.• Can conform to many contours with use of controlled heat

from hair dryer or heat gun.• Cover Trax can be used for mounting enclosures, curtains

and other panels.

Part No. Description Length (mm)

CANTRACKCWhite Cover Trax System

6000Includes Awning & Screw Cover Panel

HEAVY DUTY CENTRE MOUNT TRACK

• Flexible PVC track

• Extra strength

• Flat side profile

Part No. Description Length (mm/ft)

G515WT White HD Center Mount Track 2425 / 8

HEAVY DUTY VINYL AWNING TRACK

• UV stabilized PVC construction.• Compatible with most BI awning ropes and Keder tapes.

Part No. ColourInternal Diameter

(mm)Track Length (mm)

CANTRACK White PVC 5.5mm 6000

CANTRACKH White PVC 9mm 6000

FLEX-A-RAIL AWNING TRACK

• Flexible, non-corrosive, extruded PVC track for BI awning ropes.

• Works best with L575/LS001/LS002.• Highly flexible for easy installation.• Use flat or oval head screws to install (D355/D356).• Use 3M VHB tape to help install Flex-A-Rail.

Part No. ColourInternal Diameter

(mm/in)Overall Length (mm)

CANTRACKV3 White PVC 8 / 5/16 3000

CANTRACKV3BK Black PVC 8 / 5/16 6000

STAINLESS STEEL SCREWS FOR ATTACHING TRACK

• Use to attach Flex-A-Rail, Cover Trax and other types of awning track.

• Screws are sold in full packs of 100.

Part No. Size (mm/in) Style Head







D373 No. 6 x 3⁄4 (19) Self Tapping Oval

HD371No. 4 Head, No. 6

Body 19mm / 3⁄4 inchSelf Tapping Square

SQUARE HEAD SCREWDRIVER

• Use with D371 square head screws.

• Narrow shaft will NOT scratch Flex-a-Rail.


HC335 Size 0 Square Head Screwdriver

HC336 Size 0 Square Head Screwdriver Bit

D371

156

Accessories


Po

les

& S

lats

Poles & SlatsADJUSTABLE MOORING POLE - ALUMINIUM

• Comes with three interchangeable tips.

• No. 1 – pole end fits No. 3 spur grommet.

• No. 2 – soft vinyl tip similar to the foot.

• No. 3 – with button snap accepts standard G142 socket.

• Aluminium support pole adjusts from 1m / 40” to 1.7m / 70”.


G370 Adjusts from 1.0 to 1.7 meters/40 to 70 inches

BOAT VENT II

• UV resistant material.

• Fast installation.

• No screws or awls needed.

• Fits 3⁄4” or 7/8” tubing.

• Attach to the top of adjustable mooring pole (G370).

• Use for venting the area below the cover.


G050BK Boat Vent II - Boat Cover Support and Vent

ADJUSTABLE ANODIZED ALUMINIUM AWNING POLES


G308 Adjusts from 4 to 8 feet (1.2 to 2.4 meters)

G309 Adjusts from 6 to 12 feet (1.8 to 3.6 meters) - Heavy Duty

BOAT COVER SOCKET

• Use one or more pairs of sockets with 44mm/1 3⁄4 inch fiberglass batten material to support boat cover.

• Use No 8 flat or oval head screws.

• Sockets are sold in pairs only.


G670 Chrome Die Cast 10 pair

FIBREGLASS BOW SLAT

• Use with boat cover sockets (G670, above) forming an arch to support boat cover.

• Bow Slat/Battens are supplied in 7.6m / 25 foot lengths only.

Part No. Batten Width (mm/in) Batten Thickness (mm/in)

45NT 45 / 1 3⁄4 6 / 1⁄4

157

Accessories


New

Pro

duc

ts

New ProductsXTREME SEAL®

Xtreme Seal edge seal is a closed-cell, flexible material that can be glued or sewn to most materials and surfaces.

• Edge seal creates a three-point contact seal on most surfaces.

• Perfect choice as an edge seal on all types of custom covers.

• Can be used on convertible tops, side curtains, windshield tops, radar arches and awnings.

• Place Xtreme Seal under the binding edge on the inside of the finished surface, large bead towards the back and the small tip 1⁄8 to 1⁄4 inch revealed. Place the material and Xtreme Seal under sewing machine canvas side up.

Part No. ColourEdge Seal Length

(mm/in)Width (mm/in)

L710BK Black 44 / 1 3⁄4 30 / 100

L710WT White 44 / 1 3⁄4 30 / 100

SPRAY WELT WITH ADHESIVE

This is a new and fully functional spray welt manufactured from extruded foam rubber and is well suited for almost all applications where a tight, waterproof seal is required when a panel or enclosure is clamped into place.

• P-section design ensures maximum efficiency.• Durable extruded foam rubber composition.• Hi-tack adhesive with release paper on rear.• Sold in economical 13m/50 feet and

76m/250 feet reels.• This product is ideal weather strip for sealing:

enclosures, dodgers, covers etc.


L705BKA 1 1⁄4 " Wide Black Rubber with Pressure Sensitive Adhesive

BALL & SOCKET FITTINGS

Ball and socket design offers quick and easy fold and removal of bimini tops. A variety of tube, deck and side mounting options.• Full rotation of top frame.• Delrin inserts insure smooth movement and

tight rattle free fit.• Pin and lanyard system for secure positioning and quick

release.• Polished 316 stainless steel.


G671S 22mm/ 7⁄8 " Stainless Steel Ball Eye End

G681S 25mm/1 " Stainless Steel Ball Eye End

G678S 22mm/ 7⁄8 " Stainless Steel 90 Degree Ball Eye End

G672S 22mm/ 7⁄8 " Stainless Steel Socket Jaw Slide

G682S 25mm/1" Stainless Steel Socket Jaw Slide

G675S Stainless Steel Deck Hinge with Pull Pin & Lanyard

L710BK L710WT

G672S G682S

G671S G681S

G675S

158

Accessories


Rat

chet

Buc

kles

Ratchet BucklesSTAINLESS STEEL RATCHET BUCKLES

Stainless steel ratchet buckles (SS304) for use tying down loads and tensioning fabric.


RB800 800kg Ratchet Buckle

RB1500 1500kg Ratchet Buckle

RB1500RB800

METAL CAMLOC

Item Code

Description

CAM25B

CAM25SIL

CAM25SS

25mm (1 inch) Available in Black Enamel, Nickel & Stainless Steel Finishes

CAM50B 50mm (2 inch) Available in Black Enamel & Nickel Finishes Only

CAM25SSCAM25B

159

Accessories


Shock Cord AccessoriesCANVAS TENSION CLIP CLAMP


G380 Canvas Tension clip clamp 1/4 and 7/8

SHOCK CORD - MONOCORD

This shockcord is comprised of mono cord rubber covered by a variety of sheaths. ADVANTAGES OF MONOCORD OVER MULTIFILAMENTS:• Increased Core stability • Resistance to water and chemical impregnation

• No splaying of ends when cutting • Increased life span

• No twisting • Consistency and retention of elasticity Polyester sheaths are recommended for marine applications Polyethylene sheaths are recommended for transport applications

Item Code Size in mm Description In Rolls of

SCORE4 4 Elastic Shock Cord - Polyester Sheath - Colour: Black 100 metres

SCORE6 6 Elastic Shock Cord - Polyester Sheath - Colour: Black, White 100 metres

SCORE8 8 Elastic Shock Cord - Polyester Sheath - Colour: Black 100 metres

SCORE10 10 Elastic Shock Cord - Polypropylene Sheath - Colour: Black 100 metres

SCMPE6BLK 6 Elastic Shock Cord - Polyethylene Sheath - Colour: Black 100 metres



SUNBLOCKER CLIP


G638 Sunblocker Clip

SOLCOR WHIPPING ENDS

Item Code Shock Cord Size to Suit Description

SC9-50 To suit 6mm and 8mm Shock Cord only

Heat shrink Whipping ends onto the ends of cut cord or rope to prevent fraying. Prepackaged in packets of 12 (includes instructions)

SOLCOR JOINERS

Item Code Shock Cord Size to Suit Description In Bags of

SCAC

To suit 8mm Shock Cord onlyUseful to create various cord

formations:- Running loop

- Circles- Joining two lengths

Solcor Shock Cord Connector (3 part) 100

SCAE Suits all sizes Solcor Adjustable Shock Cord Extender 100

Sho

ck C

ord

Acc

esso

ries

160

Accessories


Shock Cord Accessories

SHOCK CORD FASTENERS

The moulded Carabina or Shock Cord Hook & Bush is rust and corrosion proof and being a totally moulded unit, the traditional metal crimp ring is eliminated. The fastening method securely grips shock cord whilst the slip ring conceals the end of the shock cord providing a neat finish.

Item Code

Sizein mm Description In Bags of

386-0373 5 Fastex Cord Hook & Bush to suit 5mm Shock Cord 100

386-0371 8 Fastex Cord Hook & Bush to suit 8mm Shock Cord 100

ROPE HOOK

Item Code Description In Bags of

SM503 Rope Hook (Black) – PLASTICSuits up to 8mm rope/shock cord 100

SA-SRH Small Rope Hook – METALSuits up to 10mm rope/shock cord 100

SA-LRH Large Rope Hook – METALSuits up to 10mm rope/shock cord 100

SOLCOR HOOK


SCAJ Suits all sizes Solsor J-Hook Adjustable Shock Cord Hook 100

SCAH To suit 8mm Shock Cord only Solcor Shockcord Hook (2 parts) 100

SOLCOR ANCHOR


SCAA Suits all sizes Adjustable shockcord Anchor 100

Sho

ck C

ord

Acc

esso

ries

161

Accessories


Shock Cord FittingsSTAINLESS STEEL SHOCKCORD HOOKS

Place shockcord through bottom hole. Squeeze shock cord clamp tightly.

Part No.For Cord Diameter:

mm/inLength: Pack Qty

HB461 6 / 1⁄4 50 / 2 50

HB462 8 / 5⁄16 62 / 2 1⁄2 50

PLASTIC SHOCKCORD HOOKS

White nylon.

Part No.For Cord Diameter:

mm/inLength: Pack Qty

HA101 3 - 6 / 1⁄8 - 1⁄4 36 / 1 7⁄16 100

HA102 8 - 10 / 5⁄16 - 3⁄8 63 / 2 1⁄2 100

PLASTIC LOCKING SHOCK CORD HOOK

Two-part hook with locking cover secures shock cord to hook without separate clamps or knots• Use for tie down cords.

Part No.For Cord

Diameter: mm/inLength: Colour Pack Qty

386-0373 5 / 1⁄4 45 / 1 3⁄4 Black Delrin 100

386-0371 8 / 5⁄16 73 / 2 7⁄8 Black Nylon 50

“S” HOOK SHOCKCORD HOOKS

Stainless steel wire.

Part No.Wire Diameter:

mm/inLength: mm/in Pack Qty

HB463 3.2 / 1⁄8 31 / 1 1⁄4 100

HB464 4.8 / 3⁄16 44 / 1 3⁄4 100

SHOCK CORD – MULTI FILAMENT

• Made in NZ this in NZ’s most trusted brand of shock cord

• Made from multi filament elastic cord

• Covered in Polyester yarn, and designed to be in NZ’s extreme UV conditions

Part No. Colour Size (mm)

SC3BK Black 3

SC3WT White 3

SC4BK Black 4

SC4WT White 4

SC5BK Black 5

SC5WT White 5

SC6BK Black 6

SC6WT White 6

SC7BK Black 7

SC7WT White 7

SC8BK Black 8

SC8WT White 8

SC10BK Black 10

SC10WT White 10

Sho

ck C

ord

Fit

ting

s

A101 A102

162

Accessories


Sho

ck C

ord

Lo

op

s

Shock Cord LoopsPASKAL BUNJEE LOOP

FORD SHOCK CORD LOOP

Tried and tested the Ford Bunji Loop attaches with no metal parts. An attaching tool is included with every bag (100 pcs).


FO160 Ford Shock Cord Loop (Black) 160mm 100



FOD Hand Die for Ford Shock Cord Loop N/A

QCD SHOCK CORD LOOP

Designed by QCD New Zealand, this loop can be attached with a rivet or Durable Post. The fastening hole can then be completely covered.

Item Code


SM615 QCD Shock Cord Loop 130mm Black. 100

SM616 QCD Shock Cord Loop 130mm White. 100










SM611 Paskal Bunjee Loop 130mm Black 100


SM602 Paskal Bunjee Loop 150mm White 100







Double this length to get the required size

163

Accessories


Tonneau AccessoriesSHOCKCORD CLAMPS

UTE BAR BRACKET


SM505

Ute Bar Bracket (Black) Secures bar to a vertical surface

Suits the multi fit ute support bar.

100


HB449 Stainless Steel Shock Cord Clamps – 3-5mmSecures ends of shock cord from fraying. 100

HB450 Stainless Steel Shock Cord Clamps – 6mmSecures ends of shock cord from fraying. 100




CLAMP PLIERS


HC449 Clamp PliersFor closing clamps Q-HB449-453

MULTI FIT UTE SUPPORT BAR


BARADJL

Tonneau Multi Fit Ute Support Bar The Tonneau Multi Fit Support Bar is designed to fit almost all Utes on the Market.

Dimensions: 1389mm (Minimum) - 1870mm (Maximum)

Tonn

eau

Acc

esso

ries

164

Accessories


Webbing (Please also refer to QCD Webbing Board)GENERAL PURPOSE WEBBING 042 - INDUSTRY STANDARD

• Canvas work• Ruck sacks/back packs

• Equestrian• Pet accessories

Item Code Tape Width in mm Breaking Strength

QCD042/12 12 (½ inch) N/A

Polyester

White W16 Black B17 Brown B09 Gold G01 Red Purple P13 Royal Blue B02 Army A02

Item Code Tape Width in mm Breaking Strength Roll Length in metres

QCD042/15 15 (5⁄8 inch) N/A 50

Polyester

White W16 Black B17 Burgundy B16 Fluro Pink P01 Grey G08


QCD042/19 19 (¾ inch) 1100 kg 50

Polyester

White W16 Black B17 Yellow Y25 Gold G01 Lime L01 Fluro Yellow Y01 Emerald G02 Bottle Green G57

Royal Blue B02 Aqua A02 Red Brown B09 Purple P13 Grey G08 Fluro Pink P01


QCD042/25 25 (1 inch) 1500 kg 50

Polyester

White W16 Black B17 Yellow Y25 Gold G01 Lime L01 Orange OR Emerald G02 Bottle Green G57

Royal Blue B02 Aqua A02 Red Brown B09 Purple P13 Grey G08 Fluro Pink P01 Maroon M19

Khaki G20 Beige B14

Web

bin

g

165

Accessories


Webbing (Please also refer to QCD Webbing Board)KEVLAR® REINFORCED POLYESTER

Cover protects Kevlar® from UV degradation and reduces flexing and chafe.Available only on full reels.

Part No. Width: mm/inReel Length:

m/yd

Breaking Strength:

kg/lbColor

HE131 35 / 1 3⁄8 25 / 27 2500 / 5500 White

DYNEEMA®

• Lighter than Kevlar and does not absorb water.• Excellent UV resistance and flex characteristics.• Dyneema is a very strong and low stretch fiber.• Available only on full reels.

Part No. Width (mm/in)Reel Length

(m)Breaking

Strength (KG)Colour

12SPEC17 12 50 1550 White

20SPEC17 20 50 2500 White

25SPEC12 25 50 1640 White

25SPEC17 25 50 3300 White

35SPEC17 35 50 4500 White

50SPEC17 50 50 6500 White

EXTRA HEAVY WEIGHT NYLON

Available only on full reels.


m/yd

Breaking Strength:

kg/lbColor

E129HD 45 / 1 3⁄4 46 / 50 5035 / 11100 White

EXTRA HEAVY WEIGHT COLORED NYLON

• Ideal for safety straps, jacklines, where maximum safety is required.

• Premium quality, best against abrasion.• Available only on full reels.


m/yd

Breaking Strength:

kg/lbColor

E136WT 25 / 1 45 / 50 2721 / 6000 White

E136RB 25 / 1 45 / 50 2721 / 6000 Royal Blue

HEAVY WEIGHT NYLON



m/yd

Breaking Strength:

kg/lbColor

E125NN 50 / 2 46 / 50 1678 / 3700 White

SUPER HEAVY WEIGHT - POLYESTER TUBULAR



m/yd

Breaking Strength:

kg/lbColor

HE124 25 / 1 46 / 50 1300 / 3000 White

HE124-HVY 25 / 1 50 / 54.7 2800 / 6200 White

Web

bin

g

166

Accessories


Web

bin

g

Webbing (Please also refer to QCD Webbing Board)SUPER HEAVY WEIGHT - NYLON TUBULAR



m/yd

Breaking Strength:

kg/lbColor

E122 12 / 1⁄2 183 / 200 700 / 1550 White

E123 19 / 3⁄4 183 / 200 1200 / 2700 White

E124NBU 25 / 1 46 / 50 1800 / 4000 Blue

E124NBK 25 / 1 91 / 100 1800 / 4000 Black

E124NYE 25 / 1 46 / 50 1800 / 4000 Yellow

E124NRD 25 / 1 46 / 50 1800 / 4000 Red

E120NBU 50 / 2 46 / 50 3600 / 8000 Blue

E120NRD 50 / 2 46 / 50 3600 / 8000 Red

E124-SDB 50 / 2 50 / 54.7 3600 / 8000 Black

P

SOFT SPUN DACRON® TUBULAR

• Soft hand tubular construction.• Excellent for sail ties.• Available only on full reels.


m/yd

Breaking Strength:

kg/lbColor

E101 29 / 1 1⁄8 46 / 50 907 / 2000 White

HEAVY WEIGHT POLYESTER (SAIL MAKER)

• Strong, low stretch webbing ideal for strapping rings on sails.

• Flat, non-tubular webbing.• Excellent UV resistance.• Very low stretch.• Minimal shrinkage.• Available only on full reels.

Part No. Width mm/inReel Length

(m)Breaking

Stength (kg)Color

QCD042-19SM 19 / 0.75 50 950 White

QCD042-25SM 25 / 1.0 50 1250 White

QCD042-38SM 38 / 1.5 50 1850 White

QCD042-50SM 50 / 2.0 50 2450 White

HERRINGBONE STYLE POLYESTER (SAIL MAKER)

• Rugged polyester webbing, five panel construction, recommended for hiking straps, bag handles, nose piece for kites, reinforcement, tie down, trampolines, etc.

• Excellent UV resistance.• Available only on full reels.

Part No. Width mm/inReel Length

(m)Breaking

Stength (kg)Color

QCD012-12SM 12 / 0.5 250 N/A White

QCD012-16SM 16 / 0.66 250 N/A White

QCD012-19SM 19 / 0.75 250 N/A White

QCD012-25SM 25 / 1.0 100 700 White

QCD012-38SM 38 / 1.5 100 1000 White

QCD042-50SM 50 / 2.0 100 1500 White

E124NYE

E120NBU

E120NRD

167

Accessories


Web

bin

g

Webbing (Please also refer to QCD Webbing Board)HEAVY WEIGHT - COLORED POLYPROPYLENE

Other colors are avail able against special order.



m/yd

Breaking Strength:

kg/lbColor

E128WT 50 / 2 91 / 100 635 / 1400 White

E128BK 50 / 2 91 / 100 635 / 1400 Black

P

HERRINGBONE PATTERN POLYPROPYLENE

Can be used as a heavyweight binding or header.


m/yd

Breaking Strength:

kg/lbColor

E130 50 / 2 91 / 100 453 / 1000 White

STANDARD WEIGHT COLORED NYLON

• Our most popular webbing.• Flat webbing.• Available only on full reels


m/yd

Breaking Strength:

kg/lbColor

E110N 12 / 1⁄2 46 / 50 317 / 700 White

E110NBK 12 / 1⁄2 46 / 50 317 / 700 Black

E111N 19 / 3⁄4 91 / 100 476 / 1050 White

E112N 25 / 1 91 / 100 680 / 1500 White

E112NBK 25 / 1 91 / 100 680 / 1500 Black

E113N 38 / 1 1⁄2 91 / 100 1020 / 2250 White

E114N 50 / 2 91 / 100 1360 / 3000 White

E114NBK 50 / 2 91 / 100 1360 / 3000 Black

BK

Black

WT

White

BK

Black

WT

White

CAUTION

Dyed nylon fibers may not be totally color fast when damp or when used in humid conditions, or if in contact with materials containing free solvents, even in trace quantities.

168

Accessories


Webbing (Please also refer to QCD Webbing Board)DIVE BELT 103 (STARCHED) WEBBING

• High tensile strength • Divers weight belt

• Marine Applications• Starch for extra stiffness

Item Code Tape Width in mm Breaking Strength Colour

Roll Length in

metres

QCD10350B 50 (2 inch) N/A Black, Colours (Special Order) 50

Polyester

SEAT BELT WEBBING 012

General Industry canvas work, Shade Sails

Item Code Tape Width in mm Breaking Strength

Roll Length in metres

QCD01225

25mm (1 inch)BLACK

1000 kg 100

COLOURS

QCD01232

32mm (1¼ inch)BLACK

1250 kg 100

COLOURS

QCD01238

38 (1½ inch)BLACK

1500 kg 100

COLOURS

100% Polyester

White W16 Yellow Y25 Gold G01 Burgundy B16 Sand B51 Emerald G02 Bottle Green G57 Olive Green G50

Khaki G20 Beige B14 Brown B09 Black B17 Grey G08 Fluro Pink P01 Scarlet S12 Purple P13

Royal Blue B02 Aqua A02 Rubi Red

QCD01250

50 (2 inch)BLACK

2000 kg 100

COLOURS

QCD01275 75 (3 inch) Black & White Only 3000 kg 100

QCD012100 100 (4 inch) Black & White Only 4000 kg 100

100% Polyester

White N99 Yellow Y25 Gold G01 Burgundy B16 Sand B51 Emerald G02 Bottle Green G57 Olive Green G50

Khaki G20 Beige B14 Brown B09 Black B17 Grey G08 Fluro Pink P01 Bright Red R12 Purple P13

Royal Blue B02 Aqua A02

50MM COLOURS

AVAILABLE COLOURS

Web

bin

g

Orange 009 Fluro Yellow Y01

169

Accessories


Webbing (Please also refer to QCD Webbing Board)


QCD10825 25 (1 inch) 2000 kg 50

QCD10835 35 (1 3/8 inch) 3000 kg 50

Polyester

W-108/50 50 (2 inch) 4500 kg 50

Polyester

QCD10875 75 (3 inch) 6500 kg 50

QCD108100 100mm (4 inch) 9500 kg 50

QCD108150 150mm (6 inch) 14000 kg 50

Polyester

White N9 Royal Blue B02 Black B17

• Tied down strap’s • Rub pad’s • High strength

LOAD BINDER WEBBING 108

White N99 Yellow Y25 Gold G01 Fluro Yellow Y01 Lime L01

Brown B09 Black B17 Grey G08 Royal Blue B02

Bottle Green G57 Scarlet S12 Purple P13

Fluro Pink P01

25 + 35MM COLOURS

White N99 Blue B27 Brown B09 Black B17 Grey G08 Fluro Pink P01 Scarlet S12 Purple P13

Orange 009 Fluro Yellow Y01

50MM COLOURS

75 + 100 +150 MM COLOURS

Web

bin

g

170

Accessories


Webbing (Please also refer to QCD Webbing Board)TRUCK BUCKLE (BASE CLIP) WEBBING 109

• High strength


QCD0209/44 44 (1¾ inch) 2500 kg 50

Polyester

White N99 Royal Blue B02 Olive Green G50 Scarlet S12 Brown B09 Black B17 Grey G08

115/126

• Softer Feel • General purpose webbing


QCD115/10 10 (3/8 inch) White Only N/A 50

QCD115/15 15 (5/8 inch) N/A 50

QCD115/20 20 (¾ inch) N/A 50

QCD115/25 25 (1 inch) 1000 kg 50

Polyester

Web

bin

g

White N99 Yellow Y25 Gold G01 Fluro Yellow Y01 Lime L01 Emerald G02 Bottle Green G57 Olive Green G50

Khaki G20 Beige B14 Brown B09 Black B17 Grey G08 Fluro Pink P01 Scarlet S12 Purple P13

Royal Blue B02 Aqua A02

171

Accessories




QCD307/16 Black & White only 16 (5/8 inch) N/A 100

QCD307/20 Black & White only 20 (¾ inch) N/A 50

QCD307/25* colours below 25 (1 inch) N/A 50

QCD307/32* Black only 32 N/A 50

QCD307/38* Black only 38 N/A 50

Polyester

• Suited for High Quality Binding • Herringbone pattern • Good strength

HERRINGBONE 307

White W16 Royal Blue B02 Navy N27 Grey G08 Beige B14 Fluro Pink P01Black B17 Olive Green G50 RedEmerald G02

TYPE 1

• Ruck sack/Bag sacks • Defence department specified webbing • General packs

Item CodeTape

Width in mm

Colours Breaking Strength

Roll Length in metres

W-TYPE1/19 19 Army G20 N/A 50

W-TYPE1/25 25 (1 inch) Army G20 N/A 50



Polyester

LEOLENE BINDING

• General Bindings • UV Stabilised • Herringbone Pattern

Item Code Tape Width in mm Colours Roll Length in metres

WT-12 12 Black and White 250


WT-25 25 Colours 100


White Black Grey Silver/Black Silver Natural Sand Navy

Royal Blue Emerald Orange Purple Blue/Silver Brown

Web

bin

g

172

Accessories


Webbing (Please also refer to QCD Webbing Board)BUDGET WEBBING - POLYPROPYLENE 605

• General purpose applications • Strapping • Bag handles

Item Code Tape Width in mm Roll Length in metres

W-605/20 20 (¾ inch) (Black only) 50

W-605/25 25 (1 inch) (Colours) 50

25MM COLOURS

White W16 Yellow Y25 Gold G01 Orange O01 Red R20 Pink P01 Burgundy B16 Brown B09

Black B17 Grey G08 Navy N27 Purple P29 Royal Blue B02 Forest G88 Emerald G32

W-605/32 32 (1¼ inch) (Colours) 50

W-605/38 38 (1½ inch) (Colours) 50

32 + 38MM COLOURS

White W16 Black B17 Gold G01 Navy N27 Red R20 Royal Blue B02

W-605/50 50 (2 inch) (Colours) 50

50MM COLOURS

White W16 Yellow Y25 Gold G01 Emerald G32 Red R20 Pink P01 Forest G88 Royal Blue B02

Black B17 Grey G08 Navy N27 Purple P29

W-605/75 75 (3 inch) (Black only) 50

CENTRE FOLD BINDING

• General bindings • Marine grade acrylic • Suits acrylic canvas colours


E095 22 183

Black White Forest Green Navy Captain Navy Cadet Grey Linen Blue

Burgundy Persian Green Beige

Web

bin

g

173

Accessories




W-406/12 12 (½ inch) 500 spools

W-406/15 15 (5/8 inch) 500 spools

W-406/20 20 (¾ inch) 100m Roll

W-406/20(400) 20 (¾ inch) 400m Spool

W-406/25 25 (1 inch) 100m Roll

W-406/25(300) 25 (1 inch) 300m Spool

W-406/32 32 (1¼ inch) 100

W-406/36 36 (1-5/16 inch) 100

• General binding tape • Black is now solution dye (UV treated) • Specifically designed for binders

BINDING TAPE 406 - TEXTURED POLYESTER

White W16 Light Beige B01 Dark Beige B08 Brown B09 Olive OG01 Black B17 Dark Grey G30 Light Grey G11

Light Blue B06 Royal R31 Navy N27 Bottle Green G33 Emerald G35 Yellow Y32 Gold G25 Red R20

Maroon M19 Purple P23 Hot Pink P22


W-5351/12 12 ½ inch) 50

W-5351/15 15 (5/8 inch) 50

W-5351/20 20 (¾ inch) 50

W-5351/25 25 (1 inch) 50

W-5351/32 32 (1¼ inch) 50

W-5351/38 38 (1½ inch) 50

W-5351/50 50 (2 inch) 50

W-5351/75 75 (3 inch) 50

• General bindings • Herringbone pattern

COTTON HERRINGBONE5351-100%COTTON

White W16

Bottle Green G88

Natural N99

Emerald G54

Yellow Y57

Sky Blue B13

Gold Y04

Blue B68

Red R40

Royal Blue B59

Scarlet Red R03A

Navy B65

Burgundy R68

Black B17

Brown B93

Grey G29

Web

bin

g

174

Accessories


10 lb grade

9 lb grade

Webbing & Staples

WELDABLE PVC WEBBING - COATED POLYESTER


W-WELD/25 25mm (1 inch)

Black (Special Order)

50

W-WELD/50B17 50mm (2 inch) 50


W-PVC/12 12 (½ inch)

White, Royal Blue, Brown (Special Order)

50

W-PVC/15 15 (5/7 inch) 50

W-PVC/19 19 (¾ inch) 50

W-PVC/25 25 (1 inch) 50

W-PVC/50 50 (2 inch) 50

PVC COATED HORSE STRAP WEBBING - PVC COATED POLYESTER

Item Code Description Tape Width in mm Roll Length in metres

W-J9 9 lb grade 50 mm (2 inch) 36

W-J10 10 lb grade (2 red stripes) 50 mm (2 inch) 36

JUTE WEBBING

Item Code Description In boxes of

80/04 Galvanised 80 series 4mm (5⁄32 inch) 10,000

80/06 Galvanised 80 series 6mm (¼ inch) 10,000



80/12 Galvanised 80 series 12mm (8 inch) 10,000


80/04SS Stainless Steel Series 80 4mm (5⁄32 inch) 10,000

80/06SS Stainless Steel Series 80 6mm (¼ inch) 10,000



80/12SS Stainless Steel Series 80 12mm ( inch) 10,000


80 SERIES STAPLES

Web

bin

g &

Sta

ple

s

175

Accessories


Hot Air Welders & Rope CutterQUICK-S HOT AIR WELDERS – HAND HELD

QUICK-S by FORSTHOFF (Germany)The hand held QUICK-S is a robust hot air welding tool used for welding PVC fabrics. Features are:• 20 temperature settings through to 700˚C• 1500 watt heater element • Carbon brushes of the motor can be replaced without

opening the tool• 1.25 kg weight including cable• 12 month warranty


F5000 QUICK-S Hot Air Welder including 40mm Wide Slot Nozzle

P

GRAND-L HOT AIR WELDERS – HAND HELD

GRAND-L by FORSTHOFF (Germany)The hand held GRAND-L is a heavy duty hot air welding tool used for welding PVC fabrics. Features are:• 20 temperature settings through to 650˚C• 3000 watt heater element• Air Flow of 450 litres/min• Carbon brushes of the motor can be replaced without

opening the tool• 12 month warranty


F1040GRAND-L Hot Air Welder

including 70mm x 4mm Slot Nozzle

P

HOT AIR WELDERS – ACCESSORIES


F4002 20mm Wide Slot Nozzle to Suit QUICK-S

F4003 40mm Wide Slot Nozzle to Suit QUICK-S

F4031 70mm x 4mm Wide Slot Nozzle to Suit GRAND-L

F4030 70mm x 10mm Wide Slot Nozzle to Suit GRAND-L


F7001 ROLLER - 45mm Pressure Welder - Single Axle

F7000 ROLLER - 45mm Pressure Welder - Double Axle

HOT AIR WELDERS – OVERLAP/TAPE WELDER

FORPLAST-P Automatic Hot Air Welding MachineThe efficient and manoeuvrable automatic hot air welding machine for truck tarpaulin processors. The FORPLAST-P automatic welding machine is a powerful tool for welding truck tarpaulins, tents and awning materials. It produces overlap welds of either 20 or 45 mm and can also be supplied as or converted to an automatic welding machine for webbing tapes on request.• The heating capacity of 3300 W, 230V AC is electronically

variable between 20 and 700 °C to suit various materials.• The automatic welding machine starts automatically when

the welding head is moved into position.• An additional cold setting cools the blower after use

without having to alter the preset temperature.• Variable speed from 0–19 m/min. ensures an optimum

welding result. 3-point surface contact of the machine ensures that pressure is evenly distributed over the tarpaulin


F1101 FORPLAST-P Automatic Hot Air Welding Machine

F1091

Tape Welding Adaptor Kit

This kit converts the FORPLAST-P lap welder into

a 50mm tape welder

ROPE CUTTER & SEALER


RC2303-C Rope Cutter & Sealer

RC2303-B Blade for Rope Cutter & SealerSingle Axle Double Axle

Hot air welding guns and

automatic welding

machines

Ho

t A

ir W

eld

ers

& R

op

e C

utte

r

176

Notes


69

Contents


Acc

esso

ries

Palms & Needles 70

Sewing Accessories & Staples 71

Cloth Clamps, Bags & Cutting Pads 72

Punches, Cutters & Hammers 73

Pattern Making Tools 74

Measuring & Lofting Tools 75

Shears 76

Sharpeners, Rippers & Cutters 77

Hot Knives 78-79

Protectants & Seam Sealer 80

Protective Cleaners & Polish 81

Cleaners & Protectants 82

Adhesives 83

Shade Sail Hardware 84

Marquee/Banner Accessories 85-86

Awning Accessories 87-90

Eyelets 91-95

Rings & Grommets 96-102

Marine Cover Fittings 103-104

Metal Fasteners 105-113

Marine Cover Fittings 114-115

DOT® Fasteners 116-117

Fastener Tools 118

DOT® Fasteners 119

Metal/Plastic Fasteners 121

Plastic Fasteners 122-127

Plastic Fasteners - Hook & Loop 128-129

Equestrian Fittings 130-136

Marine Accessories 137-141

Frame Kit & Heavy Duty Canopy Track 142

Stainless Steel Boat Top Fittings 143-148

Gemlock Collapsible Strut & Hinge 149

Tube Benders 150

Tube & Frame Accessories 151

Grab Rail & Fittings 152

Tie Down & Lacing Fittings 153

Awning Tapes 154-155

Poles & Slats 156

New Products 157

Ratchet Buckles 158

Shock Cord Accessories 159-160

Shock Cord Fittings 161

Shock Cord Loops 162

Tonneau Accessories 163

Webbing 164-173

Webbing & Staples 174

Hot Air Welders & Rope Cutter 175

70

Accessories


Pal

ms

& N

eed

les

Palms & NeedlesWILLIAM SMITH PALMS - RETAIL QUALITY

Part No. Description Style Hand

HC023 Lightweight, Non Adjustable 2 Right

HC024 Lightweight, Non Adjustable 3 Right

HC025 Lightweight, Non Adjustable 3 Left

HC026 Lightweight, Adjustable 2 1⁄2 Right

HC027 Lightweight, Adjustable 2 1⁄2 Left

HC036 Medium Weight 9 Right

HC037 Medium Weight 9 Left

WILLIAM SMITH PALMS - PROFESSIONAL QUALITY

Part No. Description Style Hand

HC028 Good Quality Seaming 11 Right

HC029 Good Quality Seaming 11 Left

HC030 Good Quality Roping 12 Right

HC031 Good Quality Roping 12 Left

HC032 Super Quality Seaming 15 Right

HC033 Super Quality Seaming 15 Left

HC034 Super Quality Roping 16 Right

WILLIAM SMITH SAILMAKERS NEEDLES

• William Smith’s best quality “Green Label” reduced edge.• Available only in full packs of 25.

Part No. Size Length (mm/in) Diameter (mm/in) Pack Qty

HC010 10 89 / 3.504 3.25 / 0.128 25

HC011 11 86 / 3.386 2.95 / 0.116 25

HC012 12 81 / 3.189 2.64 / 0.104 25

HC013 13 79 / 3.110 2.34 / 0.092 25

HC014 14 76 / 2.992 2.03 / 0.080 25

HC015 15 72 / 2.835 1.83 / 0.072 25

HC016 16 69 / 2.717 1.63 / 0.064 25

HC017 17 65 / 2.559 1.42 / 0.056 25

HC018 18 62 / 2.441 1.22 / 0.048 25

ASSORTED SIZE NEEDLES

All needles are hand-made and hand polished for ease of use.

• Tubes and packs contain assorted size needles.


HC005 5 Needles in Assorted Sizes in Packet

HC021 10 Needles in Assorted Sizes in Tube

HC022 20 Needles in Assorted Sizes in Tube

HC036

HC024

HC026

HC034

HC032

HC030

HC028

71

Accessories


Sewing Accessories & StaplesALL PURPOSE HAND SEWING NEEDLES

• Packet contains five assorted straight needles and two assorted curved needles.


HC007 All purpose hand sewing needles

SWIVEL BENCH HOOK

• Used in traditional style sailmaking to assist in holding fabric at an even tension.


HC039 Swivel bench hook

P

SEWING AWL AND ACCESSORIES

• Awl comes complete with two straight needles, waxed thread and combination wrench/screwdriver.

• Awl is ideal for sewing and doing repairs on leather and canvas.

• Replacement thread sold on reels of 11.5m/12.5 yards each.


HC910 Awl Set

HC9105 # 5 Fine Straight Needle

HC9106 # 6 Curved Needle

HC9108 # 8 Heavy Duty Straight Needle

HC911BK Black Replacement Thread

HC911WT White Replacement Thread

STAPLING PLIER

• Special Stapling Plier with High Raised Clincher• For stapling around bolt ropes or rolled up material.


B8P Raised clinch staple pliers

STAPLES

• 1 Case = 100 Boxes of 5000 Staples each

Part No. Description (mm/inch) Style Hand

STCR2115-1/4 6.3 / 1⁄4 STCR2115 B8P

STCR2115-3/8 9.5 / 3⁄8 STCR2115 B8P

STAPLE REMOVER


HC519 Metal Push-Type StaplerSe

win

g A

cces

sori

es &

Sta

ple

s

72

Accessories


Clo

th C

lam

ps,

Bag

s &

Cut

ting

Pad

s

Cloth Clamps, Bags & Cutting PadsHOLD ON CLIP

• Speedy application.• Superior gripping power.• Reusable.• Ability to relocate without puncturing or damaging

material.• Quality performance on most fabrics, netting,

polyethylene, vinyl and light polyesters.• Can be used to help hold fabric in place while patterning

on a boat frame.

Part No Dimensions (mm/in)Weight (gm/oz)

Median Holding Strength (kg/lbs)

Strength (kg/lbs)

A161WT40 x 35 x 10 mm

12.5/0.44 45 1001 1⁄2 x 1 3⁄8 x 3⁄8 in

PONY CLOTH CLAMPS

Part No. Jaw Opening (mm/in) Overall Length (mm/in)

HC515 25 / 1 102 / 4

HC516 51 / 2 152 / 6

HC517 76 / 3 229 / 9

RIGGER’S BAG

• “Cast iron” cotton tool bag.• 24 pockets. • Open top, open center for large tools.• Leather trim.• Made from 720gsm/21oz/sq yd 100% cotton duck.

Part No. Size (mm/in)

ZBAG7 356L x 229H x 191W / 14L x 9H x 7.5W

NYLON CUTTING PADS

• Helps fabric cutting tools to cut a cleaner hole.

• Keeps edges sharper.

Part No. Size (mm/in) Colour

QCDCP 250 x 250 x 13 / 10 x 10 x 0.5 Black

SAILMAKERS LEATHER

• Fuzzy leather surface both sides - E160.

• Approximate weight: 4oz/sq ft.

• Smooth surface one side, fuzzy bottom side - E162 - E163.

Part No. Style Size (m/ft)

E160 Grey Piece 0.3x0.6 / 1x2

E162 Heavy Grey Chrome - Full Hide ~1.9m2/~20sq ft

E163 Special Tan - Full Hide ~1.9m2/~20sq ft

LEATHER Grey-Natural Split 0.5 - 2m2

KNEEPADS


HC904 Rubber Pads with Hook & Loop Fastenings 1 Pair

73

Accessories


Punches, Cutters & HammersREVOLVING TUBE PUNCH

• The best revolving hole punch with 6 replaceable drive tubes ranging from 2.4 to 4.8mm/ 3⁄32 to 3⁄16 inch.

• Forged handles with copper anvil.• Industrial quality.

Part No. Length (mm/in)

HC350 230 / 9

REPLACEMENT TUBES & ANVIL FOR REVOLVING TUBE PUNCH

• Carbon steel replacement tubes and copper anvil for C350 punch (above).

Part No. Jaw Opening (mm/in) Overall Length (mm/in)

HC3500 1.9 / 5⁄64 0

HC3501 2.4 / 3⁄32 1

HC3502 2.8 / 7⁄64 2

HC3503 3.2 / 1⁄8 3

HC3504 4.0 / 5⁄32 4

HC3505 4.4 / 11⁄64 5

HC3506 4.8 / 3⁄16 6

HC350A Copper Anvil

P

ARCH HOLE PUNCHES

• Manufactured to imperial sizes.


HC151 6.3 / 1⁄4

HC152 7.9 / 5⁄16

HC153 9.5 / 3⁄8

HC154 11.1 / 7⁄16

HC155 12.7 / 1⁄2

HC156 15.9 / 5⁄8

HC157 19.0 / 3⁄4

HC158 22.2 / 7⁄8

HC159 25.4 / 1

HC160 28.6 / 1 1⁄8

HC162 34.9 / 1 3⁄8

HC163 38.1 / 1 1⁄2

HC165 51.8 / 2

MAUL MASTER

This revolutionary maul is available in two sizes and offers a dramatic improvement over the old mallet or hammer style.• Special shock absorbing, no slip rubber grip.• Special nylon compound striking surface.• Machined from aircraft aluminum.

Part No. Weight (kg/lb) Length (mm/in)

HC233 1.4 / 3.0 229 / 9

HC234 2.0 / 4.5 254 / 10

RAWHIDE HAMMER

• Traditional sailmaking tool used with punches, hole cutters, grommet dies and wherever a cushioned hit is desired, now offered in a heavy weight 1.8kg/4lb, larger face style.

Part No. Weight (kg/lb) Face Diameter (mm/in)

HC530 1.2 / 2 3⁄4 45 / 1 3⁄4

HC530R Replacement Rawhide Faces for C530

HC531 1.8 / 4 50 / 2

HC531R Replacement Rawhide Faces for C531

SIDE HOLE CUTTERS

• Manufactured to metric sizes.

Part No. Diameter (mm/in) Size

HC180 3.2 / 1⁄8 000

HC181 4.8 / 3⁄16 00A

HC182 6.4 / 1⁄4 0A

HC183 7.1 / 9⁄32 1A

HC184 9.5 /3⁄8 2A

HC185 11.1 / 7⁄16 3A

HC186 12.5 / 1⁄2 4A

HC187 15.9 / 5⁄8 5A

HC188 19.0 / 3⁄4 6A

HC189 22.2 / 7/8 7A

HC190 25.0 / 1 8A

Pun

ches

, C

utte

rs &

Ham

mer

s

C3500 C350A

C530

C530R

74

Accessories


Pat

tern

Mak

ing

To

ols

Pattern Making ToolsPUSH PINS

• Order quantity: 1 full pack equals 100 pins.

Part No Description Colour Pin Length (mm/in) Pieces Per Pack

HC903BK Plastic Head Black 14 / 9⁄16 100

HC903FP Plastic Head Hot Pink 14 / 9⁄16 100

HC903 Aluminum Head Silver 16 / 5⁄8 100

AWLS

Part No. Description Length (mm/in) Pack Qty

HC901 Yellow Handle Standard 100 / 4 20

HC900 Yellow Handle Heavy Duty 130 / 5 1⁄2 12

STAEDTLER NON-PERMANENT OMNICHROM

Ideal for making marks on Docril, TopGun or most other fabrics and vinyls.

• Use a moist sponge or damp fabric towel to remove pencil marks.

• Pencils do not contain wax.

• Ideal for marking on Docril, Top Gun or most other fabrics including vinyl.

• Water soluable.

Part No. Colour Pencils per box

SSCPWTWS White 12

SSCPBKWS Black 12

SSCPBLWS Blue 12

SSCPYLWS Yellow 12

STAEDTLER NON PERMANENT – OMNICHROM REFILL PENS

• Refillable leadholder in 4 colours

• No sharpening necessary

• Can be wiped off smooth textiles

• Washes out of many textiles

Part No. Colour Refills per box

SSCPKIT White Pen 12

SSCPLW White 12

SSCPLBK Black 12

STAEDTLER NON-PERMANENT GASOCHROM

Marks on boat top, industrial vinyls, glass, window vinyl, polycarbonate or any polished surface.

• String-pull sharpening.

• Wipes off easily with a damp cloth.

• Wax based.

Part No. Colour Pencils Per Box

SSCPWT White 12

SSCPBL Blue 12

SSCPBK Black 12

SSCPYL Yellow 12

SSCPRD Red 12

MARKING-OUT CHALK

• H.Hancock tailors chalk.

• Available only as a full pack.

Part No. Colour Pack Qty

TCWW White 50

TCWA Assorted box of Colours 50

C903BK C903FP C903

C901

C900

SSCPBLWS

SSCPWTWS

CAUTIONNOTE: Always test effectiveness of omnichrom and gasochrom on a scrap piece of the exact material before use on a new project.

75

Accessories


Measuring & Lofting ToolsMEASURING TAPES - METAL

• Impact resistant ABS case with winding handle.• Double sided 10mm blade: meters x centimeters /

millimeters reverse side: feet x inches / 1⁄8 inches.


HC705 30m/100ft Steel Tape

MEASURING TAPES - FIBREGLASS

• Impact resistant case.• C713 - Graduated top edge: feet x inches/ 1⁄8 inches

bottom edge: meters x centimeters/millimeters.• C716 - Graduated top edge: feet x inches/ 1⁄10 inches

bottom edge: meters x centimeters/millimeters.

Part No. Description Scale

C713 30m/100ft/ Fiberglass ft-in/m-mm

C706 30m/100ft/ Fiberglass ft/1⁄10 ft

ALUMINIUM RULERS

• Used to make straight edge for drawing or cutting.

Part No. Description Length (m/ft) Width (mm/in)

HC710 Imperial/Metric 1.00 / 3.28 31.2 / 1 1⁄4

HC711 Imperial Only 1.83 / 6.00 50.8 / 2

FIBREGLASS LOFTING BATTENS

• Additional transport charges may be applicable.

Part No. Lentgh Section (mm)

LOFTBAT 25m, cut lengths available 10mm x 15mm

LOFTBATPU 25m cut lenghts available 35mm x 7mm

MYLAR® PATTERN MATERIAL

Part No StyleRoll Length

(m/yd)Width (mm/in)

Thickness (microns/in)

E062 Pale Blue Clear 25.0 / 27.3 1145 / 45.0 175 / 0.007

E063 Opaque White 47.5 / 50.0 1370 / 54.0 190 / 0.0075

PATTERN-XX™ MATERIAL

• High quality semi-opaque product offering the best way to pattern a wide variety of projects.

• Manufactured from high quality polyethylene filaments coated on both sides to provide excellent tear strength and directional stability.

Part No. Description Thickness (mm/in) Roll Length (m)

PENAT 2050mm Wide 0.12 / 0.005 50

Mea

suri

ng &

Lo

ftin

g T

oo

ls

CAUTION

NOTE: Always check the position of point zero before use.

C711

C710

Cross section C920/2/4

E062

76

Accessories


Shea

rs

ShearsKNIFE EDGE SHEARS

• One blade is ground to a knife edge for cutting synthetic fiber.

Part No. Wiss # Length (mm/in)

C550-10 1225 Polished 254 / 10

C550-12 1226 Polished 305 / 12

INDUSTRIAL SHEARS

• Nickel plated blades.


C551-7 27 178 / 7

C551-8 28 203 / 8

C551-9 29 229 / 9

HEAVY DUTY SHEARS

• Polished blades.


HC552-10 20 254 /10

HC552-12 22 305 /12

HC552L-10 20 Left Hand 254 / 10

EXTRA HEAVY DUTY SHEARS

• Polished blades with fully contoured handles.


HC555-10 20W 254 / 10

HC555-12 22W 305 / 12

THREAD SNIPS

• C554 Plastic with replaceable stainless steel blades.

• C553 Self-opening spring action snips.


HC554 Professional Quality Thread Snips

HC554RK Replacement Blades for C554

HC553 Self Opening Spring 121mm/43⁄4in

STAINLESS STEEL SHEARS

• Premium stainless steel, light weight scissors with knife edge and matt black polypropylene handles to prevent slippage.

• Light weight.

• Adjustable pivot assembly protected by “red button”.

• Will not rust on the boat or in a sail repair kit.


HC560-9 229/ 9

SOFT HANDLE AMBIDEXTROUS SHEARS

• Cushion soft handles with micro serrated blade offer maximum control.

• Ergonomic design for hours of cutting comfort.

• Works with either right or left hand.


HC560-8 203 / 8

C553

C554

77

Accessories


Sharpeners, Rippers & CuttersINDUSTRIAL STRENGTH CABLE CUTTERS

• Precision Cutters by Felco (Swiss Made)• Designed to cut wire rope.

Part No. Type Max Cable (mm/in)Cutter Length

(mm/in)

FEC12 C-12 10 / 3⁄8 480 / 19

FEC16 C-16 15 / 5⁄8 580 / 23

SEAM RIPPERS


HC905 Small for Spinnaker Seams

HC906 Deluxe Quality

CLAUSS HEAVY DUTY SHEARS

• Polished blade, Hot forged bent trimmers

Part No. Clauss # Length (mm/in)

HC552-10CL 20 254 / 10

HC552-12CL 22 305 / 12

CLAUSS HEAVY DUTY BIG BOW RUBBER HANDLE

• Polished blade, Big bow rubber handle


HC556-12CL 18 292 / 11.5

CLAUSS EXTREME EDGE

• 9” Titanium Bonded Blades

• Titanium bonded blades are three times harder than stainless steel blades so they last longer!

• Perfect for cutting, quilt, wool, corduroy & Denim

• Lifetime warranty


HC560-CL 16 228 / 9

CLAUSS ULTRAFLEX BENT SHEAR

• 8” High carbon alloy steel

• Micro-Serrated blades for cutting Kevlar

• Lifetime warranty


HC560-KEVLAR 14 203 / 8

CABLE CUTTERS

• Precision Cutters by Felco (Swiss Made)• Designed to cut wire rope.

Part No. Type Max Cable (mm/in)Cutter Length

(mm/in)

FEC7 C-7 5 / 3⁄16 190 0 / 7 1⁄2

FEC9 C-9 6 ⁄ 1⁄4 320 / 12 1⁄2

Shar

pen

ers,

Rip

per

s &

Cut

ters

FEC7

FEC9

HC906

HC905

78

Accessories


Ho

t K

nive

s

Hot KnivesENGEL HOT KNIFE

• Designed to cut and seal synthetics, woven and knit fabrics, and cut and weld rope, cord and webbing.

• Quick heating with built in spot lights.

• Combine with optional blades for a variety of uses.

• Engel hot knife is sold without blades - see below for order details.

• Offered in two voltage styles for North American or worldwide use.

Part No DescriptionOverall Length

(mm/in)Heats To Volt Watt

HC851 HSGO - US 254 / 10 1000°F 110 70

HC850 HSGO - Euro 254 / 10 1000°F 220 60

ENGEL CUTTING ATTACHMENTS

• Combine blades with trigger action handle to produce hot tool.

• C852 - Use with C854 or C856 cutting foot.

• C853 - Excellent for applique work, cut and seal synthetics.

• C854 - Holds material down while cutting. Use C852 blade. Does not require special cutting surface.

• C856 - Use C852 blade. Does not require special cutting surface.

Part No. Description Ref

HC852 Standard Blade 100R

HC853 Precision Blade HSO

HC854 Adjustable Base Cutting Foot SF

HC856 Cutting Foot

PORTASOL HOT KNIFE KIT

Totally portable, four-in-one kit in polypropylene travel case.

Kit includes:

• Hot knife with adjustable power levels • Hot blow • Blow torch • 2.4 mil Soldering tip • Safety stand • Built-in ignitor cap

Part No. Overall Length (mm/in) Weight (oz) Heats To

C835 165 / 6 1⁄2 4.5 750°F

C831 Hot Knife Tip (not included with tool)

ULTRATORCH HEAT TOOL

• Industrial strength portable gas heat tool with soldering tip.

• Becomes rugged and transportable hot knife with hot knife replacement tip (C882).

• Faster and easier to use than all other gas hot knives.

• Self-igniting with adjustable power levels.

• Standard tip is a 2.0 mil soldering tip.

• Operates for approximately 3 hours at number 3 setting.

Part No. Overall Length (mm/in) Weight (oz) Heats To

C880 267 / 10 1⁄2 5.5 950°F

C882 Hot Knife Tip (not included with tool)

CAUTIONEngel Hot Knife is designed for intermittent operation and should not be used for more than 20 minutes at one time without pause.

HC854 HC856

HC852 HC853

C831

C835

C880

C882

79

Accessories


Hot KnivesUNGAR HOT KNIFE HANDLE & HOLDER

• Easy to hold power source handle to be used with either the basting tip or cutting tips below.

• Store the tool in the holder to act as a safety guard against accidents.

• Combine with tips below to produce hot knife or fusing tool.

• Easily lower or control tip temperature using the Heat Control Unit C806.

• Metal mesh cage protects from accidents.

Part No DescriptionHandle Length

(mm/in)

Overall Length (mm/in)

Heats To

Volt Watt

HC840 Handle 140 / 5 1⁄2 210 / 8 1⁄4 850°F 110 18

HC841 Tool Holder

UNGAR TIPS

• Combine tips with handle to produce hot knife or fusing tool.

• C842 - Copper cutting tip is not replaceable.• C843 - Add to C844 hot cutting tip to make complete hot

knife.• C844 - Use with C843 element to produce cutting tip.• C845 - Use on synthetic materials to fuse pin hole for

temporary joining prior to sewing.

Part No. Description Watt

HC842 65S Cutting Tip Complete 50

HC843 37 Heating Element Only 50

HC844 100 Cutting Tip Only

HC845 33 Nyla Base Tip Complete 23

BENCH MOUNT HOT KNIFE

• Unit comes with base and one 4 inch cutting blade.

• Great for quick, clean cuts of rope or webbing.

Part No. Volt Heats To

RC2303-C 240 1200°F

HOT TOOL HOT KNIFE

The Hot Tool hot knife was recently introduced to the Bainbridge International line of cutting and sealing equipment. This light weight, easy to hold tool has a heating element which slides inside the selected tip attachment allowing a very efficient use of heat. Tips may be interchanged for cutting, sealing or circle cuts.• Easy to hold tools with hot knife blade included.• Heats quickly up to working temperature.• Heat element of tool fits inside tip for greater efficiency.• No warranty.

Part No DescriptionHandle Length

(mm/in)

Overall Length (mm/in)

Heats To

Volt Watt

C860 Light Duty 89 / 3 1⁄2 152 / 6 850°F 110 18

C861 Heavy Duty 127 / 5 241 / 9 1⁄2 1050°F 110 18

HOT TOOL BLADES & CIRCLE CUTTERS

• C862/865 - Replacement tips slide over heat element of C860 and C861 for heat efficiency.

• C864/866 - Circle cutters are great for putting a heat sealed round hole in webbings and fabrics.

Part No. Description Scale

C862 Knife Blade for C860 254 / 10

C865 Knife Blade for C861 305 / 12

C864 Circle Cutter for C860 4.8 / 3⁄16

C866 Circle Cutter for C861 6.3 / 1⁄4

HEAT CONTROL

• Precision dial temperature controller. Unit can also extend life of hot knife tip.

• Use with either C840, C860 or C861 to lower the operating temperature of the tip.


C806 Heat Control Unit

Ho

t K

nive

sCAUTION

With all hot knife elements and tips, it is important not to drop tool as it will have similar results to a light bulb element breaking.

C840 C841

C842 C843

C844C845

C861C860

C865 C866

80

Accessories


Pro

tect

ants

& S

eam

Sea

ler

Protectants & Seam SealerSPF-UV™ SUN PROTECTIVE FILM WIDE ROLLS

• Clear UV resistant film with adhesive backing that blocks virtually all damaging UV radiation.

• Weighs only 81gsm/1.9smoz.

• For application on roller furling genoas or to protect other materials from the effects of UV rays.

Application recommendations: • Use on a clean surface - dirt and salt will prevent adequate bond. • Stretch sail to be flat and free of wrinkles. • Apply SPF-uv in sections (do not attempt one piece head to clew or tack to clew). • Keep minimum tension on SPF-uv to keep it flat but not distorted. • Allow sufficient time for maximum bonding after applying SPF-uv. • Roll sail with film to the outside of roll. • Check for parts of the mast and rigging that could chafe sail.

• Cut lengths available.

Part No. Width (mm) Roll Length (m/yd) Film

HJ820 508 45.72 / 50 Clear

HJ830 762 45.72 / 50 Clear

HJ860 1524 45.72 / 50 Clear

SPF-UV™ SUN PROTECTIVE FILM NARROW TAPES

• Repair clear film products.

• Pressure sensitive adhesive.

Part No. Width (mm) Roll Length (m/yd) Film

HJ823 25mm 45.72 / 50 Clear

HJ822 50mm 45.72 / 50 Clear

HJ821 75mm 45.72 / 50 Clear

SEAM KOTE™ - PLASTISEAM

• Weather resistant plastic coating to protect seams from abrasion.

• Use on all types of outdoor fabrics: tents/backpacks/awnings/boat tops/sails.

• 60ml/2floz will seal approx. 40m/140 feet of seams.

Part No. DescriptionLiquid Measure

(ml/floz)Case Qty

M003 Can with Brush Top 355 / 12 24

M004 Gallon Refill 3785 / 128 4

SEAM KOTE™ 4

Water borne urethane coating which exhibits excellent durability, flexibility and washability.

• Lightfast and UV resistant.

• Soft, flexible clear film upon drying.

• Abrasion and impact resistant.

• Good adhesion to a variety of substrates.

• Contains no aromatic solvents.

• Fast drying and easy to clean.

• Keep from freezing.


(l/gal)Case Qty

M150 Seam Kote 4 3.8 / 1 4

M151 Seam Kote 4 18.5 / 5 1

SPF-uvSPF-uvS U N P R O T E C T I V E F I L M

M003 M004

81

Accessories


Protective Cleaners & PolishNOVUS PLASTIC POLISH

• Novus system provides everything to clean, shine and protect.

• Novus 1 gently cleans plastic without scratching. Leaves shines that resists fogging, repels dust and eliminates static. Contains no abrasives.

• Novus 2 removes fine scratches and haziness, helps restore faded and discolored plastics.

• Novus 3 Removes heavy scratches and abrasion from most acrylic surfaces. Use when damage is too severe for No. 2 polish.

• Use on Lexan, Plexiglass, clear vinyl, monofilm, polycarbonate, etc.


(ml/floz)Case Qty

HM174KIT Novus#1, #2, #3 & Polish Mates 59 / 2 12

HM171 Novus#3 59 / 2 12

HM181 Novus#1 236 / 8 12

HM172 Novus#2 59 / 2 12

HM182 Novus#2 236 / 8 12

HM173 Novus#3 59 / 2 12

HM183 Novus#3 236 / 8 12

HM180 Polish Mates Cloth (10 per pack) –– 12

IMAR STRATAGLASS PROTECTIVE CLEANER

• Uniquely formulated to clean and shine and protect strataglass & crystal clear 20/20.

• Special UV inhibitors extend the useful life of Strataglass by minimizing the deteriorating effects of sunlight.

• Safe for use daily and recommended to use often.


(ml/floz)Case Qty

HM221/4 Pump Spray 118 / 4 24

HM221/16 Pump Spray 473 / 16 12

IMAR STRATAGLASS PROTECTIVE POLISH

• Formulated to safely clean, polish and protect Strataglass and Crystal Clear 20/20.

• Creates a nearly invincible protective barrier against the damaging effects of marine environment pollutants.

• Recommended for use every 2 – 3 months.

• Frequent use of Imar Strataglass Protective Cleaner between polishing will increase protection.


(ml/floz)Case Qty

HM222/4 Bottle 118 / 4 24

HM222/16 Bottle 473 / 16 12

Pro

tect

ive

Cle

aner

s &

Po

lish

M171 M172 M173

82

Accessories


Cle

aner

s &

Pro

tect

ants

Cleaners & Protectants"303" FABRIC CLEANER

• Non hazardous – NO caustic chemicals or solvents.

• Meets or exceeds EPA standards for biodegradability.

• Safe for all water-safe materials.

• Rinses residue free.

• Powerful for heavy degreasing.

• Can be used at full strength or recommended dilution.


(ml/floz)Case Qty

M020 Trigger Spray 946 / 32 8


"303" ULTRA-VIOLET PROTECTION

• 303 is excellent for preventative maintenance, with a UV screen that reduces fading and degradation due to ozone, acid rain and weather.

• Non-hazardous and biodegradable. No petrochemicals.

• Not oily or greasy - will not attract dust.

• Use on rubber, plastic, fiberglass, plexiglass, vinyl, leather, canvas and woven polyester fabrics.

• Application: Spray on. Wipe dry. Apply once or twice a year. Apply more often where UV exposure is extreme and constant. 236ml/8floz should cover approximately 13m2/140 square feet.


(ml/floz)Case Qty

M009 Pump Spray 59 / 2 24

M010 Pump Spray 236 / 8 12



"303" HIGH TECH FABRIC GUARD

303 High Tech Fabric Guard is powerful enough to protect fabrics in the harshest environments outdoors. Yet 303 High Tech Fabric Guard is safe for the finest fabrics, wool, silk and fine leathers.

• Superior performance, coverage and durability

• Soil and stain resistance, to store and maintain water repellence on outdoor fabrics and UV screening.

• Protects against both water and oil based stains. Treated fabrics take longer to soil and clean-up more easily.


(ml/floz)Case Qty

M014 Pump Spray 59 / 2 24


M015A Trigger Spray 950 / 32 8


M017 5 Gallon Refill 18927 / 639 1

M009M012M010

M016M013

83

Accessories


Adhesives3M BRAND SUPER 77 SPRAY ADHESIVE

• Very high bond strength.• An extremely versatile spray

adhesive that permits either a temporary or permanent bond with a new “low mist” formula.

• Fast, aggressive tack for bonding most light weight materials.

• Best on two surfaces.• Bonding range: 15 minutes one

surface/30 minutes two surfaces.• Coverage: 20.4m2/220 square feet.• Clear adhesive with fine mist.• No CFC’s.


(ml/floz)Case Qty

HJ959 Aerosol 710 / 24 12

ADHESIVE REMOVER

A specially blended solvent that provides easy cleanup of most types of adhesive and quickly removes waxes, road tars, grease, oil and similar materials. Will not harm vinyl or fabrics when properly used. Always try on a small area of similar material before use on a sail or cover• Easy to apply.• Non-Toxic.• Non-Allergenic.• Much safer than acetone.

Part No. Liquid Measure (ml/oz)

HM040 909 / 32

ADOS GLUE F2 MULTIPURPOSE CONTACT ADHESIVE

• High Performance general purpose contact adhesive

• Exceptional performance for making bonds with laminated plastics, hardboard, sheet metals, foam plastics, some rubbers, felts, acoustic tiles, leather, most building materials, etc.

Part No. Description Liquid Measure (ml) Case Qty

GLUF2SPRAY F2 Spray Can 575 12

GLUF2SPRAY210 F2 Spray Can 210 12

GLUF220F2 clear, 20 litre

jerry can20000 1

ADOS GLUE F38 HIGH HEAT CONTACT ADHESIVE

• High heat, high strength contact adhesive

• Exceptional performance for making bonds with, head linings in cars and boats. Fabrics and vinyls.

Part No. Description Liquid measure (ml)

GLUF3820 F38 clear, 20 litre jerry can 20000

ADOS GLUE F55 SPRAYABLE

• Multipurpose sprayable contact adhesive

• Exceptional performance for making bonds with polyurethane foam, fabrics, some cloth backed vinyls.

• Designed specifically for commercial contractors that need to spray large areas therefore it has a long bonding time.


GLUF5520 F55 Clear, 20 litre jerry can 20000

ADOS GLUE F92 SHORT TACK

• Formulated to offer very controlled spraying with air driven spray equipment.

• Low odor, when sprayed it generates virtually no mist.

• Designed for use with polyurethane foam, head linings in cars and boats, some fabrics and vinyls.


GLUF9220 F92 Clear, 20 litre jerry can 20000

ADOS F81 PVC GLUE

• High strength polyurethane adhesive

• Specifically designed for PVC’s, vinyls, plastics, Inflatable boats and tarpaulins.


GLUF811 F81, clear 1 litre can 1000

GLUF814 F81, clear 4 litre can 4000

Ad

hesi

ves

CAUTION

Warning: Always test adhesive bond strength for your material and application.

84

Accessories


Shad

e Sa

il H

ard

war

e

Stainless Steel HardwareWIRE CUTTER

Item Code

Description

FEC9Felco Wire Cutter

Swiss Made Cuts up to 6mm wire

HAND FERRULE (SWAGE) PLIERS

Item Code

Description

DWS3Hand Pliers for Ferrules (Swages) 3mm

Used for crimping ferrules on to wire size 3mm only

DWS4Hand Pliers for Ferrules (Swages) 4 and 5mm

Used for crimping ferrules on to wire size either 4 or 5mm

DWS6Hand Pliers for Ferrules (Swages) 6mm

Used for crimping ferrules on to wire 6mm only

Endeavour RingsEndeavour Rings are specifically designed for the sail making and PVC structure industry. Produced from 316L Stainless Steel the Endeavour Ring is a product designed for maximum strength and durability offering superior holding power.

ENDEAVOUR RINGS

Item Code

Stainless Steel Grade

Inside Diameter

Hole Punch Diameter

Maximum Load Deformed / Collapses

Box Size

ENDRING10 316 L 10 mm 11 mm 173 kg / 400 kg 50

ENDRING12 316 L 12 mm 13 mm 259 kg/ 500 kg 50


ENDRING17 316 L 17mm 18mm N/A 50



ENDRING30 316 L 30 mm 32 mm N/A 50




N D E A V O U R R I N G S

85

Accessories


Mar

que

e/B

anne

r A

cces

sori

es

KederKEDER

Item Code

DescriptionRoll Length 100 Metres

KED4S 4mm White Single Sided 100

KED4DW 4mm White Double Sided 100

KED4DBL 4mm Black Double Sided 100

KED55DW 5.5mm White Double Sided 100

KED6S 6mm White Single Sided 100

KED75SW 7.5mm White Single Sided 100


KED75DB 7.5mm Black Double Sided 100


KED85SW 8.5mm White Single Sided 100


KED11DW 11mm White Blockout Double Sided 100 / 250

KED13DW 13mm White Blockout Double Sided 100

KEDER DIMENSIONS

DescriptionInner Core

ColourD

mmF

mmX

mm

7.5mm Single Sided Yellow 7.5 25 10

7.5mm Double Sided Yellow 7.5 25 10

8.0mm Double Sided Green 8.0 25 10

8.5mm Single Sided Red 8.5 25 10

11mm Blockout Double Sided

Black 11.0 42 10

13mm Double Sided Black 13.0 42 10

8.0mm Clear N/A 8.0 20 N/A

CLEAR KEDER

Item Code

DescriptionRoll Length100 Metres

KEDCL8 8.0mm Clear Keder with 20mm tail 100

KEDCL8T 8.0mm Tinted Clear Keder with 20mm tail 100

KEDER FITTINGS

Place the drill guide at ther end of the Keder. Drill a 25mm deep hole and remove the drill guide.

Use a hot air gun and heat the Keder Splice or Keder Shield to approximately 250 degree Celcius and insert into the predrilled hole.

Item Code

DescriptionDimensions

mm

KEDS11 Keder ShieldGoes onto the end of Keder to prevent fraying and easy insertion into track

D - 11 | d -5 | L - 23

KEDS13 D - 13 | d -5 |L - 23

KEDSP5Keder Splice Plug

Used for joining KedarD - 5 | d -3.2 | L - 50

KEDDG11 Keder Drill GuideUsed to fit the Keder Shield and Keder Splice.

D - 11 | d -4

KEDDG13 D - 13 | d - 4

d

d D

DL

L

D

D

X

X

DFF

Clear Single

Double

F

D

D

X

X

DFF

Clear Single

Double

F

D

D

X

X

DFF

Clear Single

Double

F

86

Accessories


Mar

que

e/B

anne

r A

cces

sori

es

Awning AccessoriesPLASTIC SAIL TRACK – UV TREATED

Item Code Description Material Track Length

PK64Plastic Sail Track

Suitable to be used with KEDER sizes 7.5mm, 8.0mm and 8.5mmPlastic 3 mtr

• More track on page 91

Marquee/Banner/Flag FittingsROPE – SILVER PE

Polyethylene Silver Rope is a general purpose rope. Soft on the hands, it is easy to handle and flexible. Silver PE rope has added ultra-violet stabilizers and its hairy finish gives this rope good grip.

Item Code Size Breaking Strength (kg) Roll Length (m)

SR4 4mm 208 250

SR6 6mm 376 250

SR8 8mm 622 250

SR9 9mm 772 250

SR10 10mm 944 250

SR12 12mm 1260 250

ROPE – DANLINE 3 STRAND PPE

• Made in New Zealand, Duradan PPE rope is made from blending Polypropylene and Polyethylene resins.

• Floats on water

• Is UV stabilized for New Zealand’s extreme UV conditions

• Available in 3mm – 48mm on 110m and 220m reels

Item Code Size / Colour Breakind Load (kg) Roll in meters

R5PPE 5mm White 465 220

R5PPEGRN 5mm Green 465 220


R6PPEB 6mm Black 727 220

R6PPEY 6mm Yellow 727 220








Fig 1

Fig 2 Fig 3

Fig 1

Fig 2 Fig 3

87

Accessories


Aw

ning

Acc

esso

ries

Crank Gearbox AwningCRANK GEARBOX AWNING SYSTEM


AWM6NUT M6 Nuts for Gear Box brackets & plates

AWM640B M6 Bolt for Gear Box Stainless Steel 40mm

AWGB91B Geiger Gear Box 9:1 Black made in Germany

AWGB91W Geiger Gear Box 9:1 White made in Germany


AWPPP Pivot Pin & Plate

AWPPPSS Pivot Pin & Plate - Stainless Steel

AWM6NUT Nuts for Pivot Pin & Plate - Stainless Steel

AWM612B Screws for Pivot Pin & Plate 12mm - Stainless Steel


AWDE63 Drive End 63mm




AWIE63 Idler End 63mm



CRANK HANDLES

Item Code Description Material

AWCH0900 Crank Handle 900mm White






88

Accessories


Universal Awning ComponentsAWNING GEARBOX BRACKETS


AWGBBKT60HDSS 60mm Stainless Heavy Duty Gear Box Bracket


AWGBBKT65SS Awning Bracket 65mm - Stainless

AWGBBKT65W Awning Bracket 65mm - White

AWGBBKT65B Awning Bracket 65mm - Black

AWGBBKT65G Awning Bracket 65mm - Grey


AWGBBKT80SS Awning Bracket 80mm - Stainless

AWGBBKT80W Awning Bracket 80mm - White

AWGBBKT80B Awning Bracket 80mm - Black

AWGBBKT80G Awning Bracket 80mm - Grey


AWGBPLSS Awning Plate 65mm - Stainless

AWGBPLW Awning Plate 65mm - White

AWGBPLB Awning Plate 65mm - Black

AWGBPLG Awning Plate 65mm - Grey

Aw

ning

Acc

esso

ries

89

Accessories


Aw

ning

Acc

esso

ries

Universal Awning AccessoriesKEYWAY TUBE


AA-02-201 Keyway Tube 63mm - 5.6m Steel Zincalume

AA-02-202 Keyway Tube 63mm - 6.5m Steel Zincalume


AWTUBE70 Keyway Tube 70mm Aluminium - 5m

AWTUBE706 Keyway Tube 70mm Aluminium - 6m


AA-02-401 Keyway Tube 78mm STEEL Lock Seam - 5.8m

90

Accessories


CordPOLYESTER CORD

Item Code Description Spool Size in metres

CJ30W Coarse Polyester Braid 3mm White 100

CJ30B Coarse Polyester Braid 3mm Black 100







SASH CORD

Item Code Description Spool Size in metres

SASH35 3.5mm (No.4) 150m Polyester Sash H/L WHT 150

SASH35BK 3.5mm (No.4) 150m Polyester Sash H/L BLK 150

SASH3HL 3.0mm (No.3) 150m Polyester Sash H/L WHT 150

SASH4 4.0mm (No.5) 150m Polyester Sash H/L WHT 150

SASH5 4.0mm (No.5) 150m Polyester Sash WHT 150



SASH6PK 6.0mm (No.6) 150m Polyester Sash WHT 150


SASH78BK 7.8mm (No.9) 150m Polyester Sash BLK 150


SASH8PKBK 7.0mm (No.8) 150m Polyester Sash BLK 150

SASH9 9.0mm (No.10) 100m Polyester Sash 150

NOTE: Please refer to Rope catalogue for full stock range.

Aw

ning

Acc

esso

ries

91

Accessories


SELF PIERCING EYELET DIMENSIONS

SizeA

Internal Diameter After Fitting

BBarrel Length

CExternal Diameter

SP0 4.8mm 5.2mm 9.6mm

SP1 6.5mm 4.8mm 12.8mm

SP3 8.0mm 5.6mm 19.1mm

SP4 9.5mm 6.6mm 20.6mm

SP6 11.1mm 6.8mm 21.8mm

SP7 12.7mm 7.4mm 26.5mm

SP9 15.6mm 8.4mm 31.8mm

SP20 42mm 12.1mm 63.5mm

EyeletsBRASS SELF PIERCING EYELETS

Item Code Size In boxes of

EYELET

EB0 SP0 3,000

EB1 SP1 3,000

EB3 SP3 1,000

EB4 SP4 1,000

EB6 SP6 500

EB7 SP7 500

EB9 SP9 250

SPUR WASHERS

EBSW3 SP3 1,000

EBSW4 SP4 1,000

EBSW6 SP6 500

EBSW7 SP7 500

EBSW9 SP9 250

PLAIN (FLAT) WASHERS

EBP0 SP0 3,000

EBP1 SP1 3,000

EBP3 SP3 1,000

EBP4 SP4 1,000

EBP6 SP6 500

EBP7 SP7 500

EBP9 SP9 250

NICKEL PLATED SELF PIERCING EYELETS


EYELET

EN0 SP0 3,000

EN1 SP1 3,000

EN3 SP3 1,000

EN4 SP4 1,000

EN6 SP6 500

EN7 SP7 500

EN9 SP9 250

SPUR WASHERS

ENSW3 SP3 1,000

ENSW4 SP4 1,000

ENSW6 SP6 500

ENSW7 SP7 500

ENSW9 SP9 250


ENP0 SP0 3,000

ENP1 SP1 3,000

ENP3 SP3 1,000

ENP4 SP4 1,000

ENP6 SP6 500

ENP7 SP7 500

ENP9 SP9 250

Eye

lets

Plain Washer

Plain Washer

Spur Washer

Spur Washer

Self piercing eyeletRefer to diagram for dimensions

Self piercing eyelet

C

C

B

B

A

A

Eyelet B

C

A

92

Accessories


Eye

lets

EyeletsBLACK PLATED SELF PIERCING EYELETS


EYELET

EBLK0 SP0 3,000

EBLK1 SP1 3,000

EBLK3 SP3 1,000

EBLK4 SP4 1,000

EBLK6 SP6 500

EBLK7 SP7 500

EBLK9 SP9 250

SPUR WASHERS

EBLKSW3 SP3 1,000

EBLKSW4 SP4 1,000

EBLKSW6 SP6 500

EBLKSW7 SP7 500

EBLKSW9 SP9 250


EBLKP0 SP0 3,000

EBLKP1 SP1 3,000

EBLKP3 SP3 1,000

EBLKP4 SP4 1,000

EBLKP6 SP6 500

EBLKP7 SP7 500

EBLKP9 SP9 250

STAINLESS STEEL SELF PIERCING EYELETS


EYELET

ESS3 SP3 1,000

ESS4 SP4 1,000

ESS6 SP6 500

ESS7 SP7 500

ESS9 SP9 250

SPUR WASHERS

ESSSW4 SP4 1,000

ESSSW6 SP6 500

ESSSW7 SP7 500

ESSSW9 SP9 250


ESSP3 SP3 1,000

ESSP4 SP4 1,000

ESSP6 SP6 500

ESSP7 SP7 500

ESSP9 SP9 250

Plain WasherSpur Washer


C

B

A

Plain WasherSpur Washer


C

B

A

93

Accessories


EyeletsSP20 CURTAIN EYELETS – NICKEL PLATED


EN20Steel Nickel Plated SP20

EYELET & WASHER SET100

VENTED BED EYELETS – BRASS


EBVENT Vent 500

EBVNTEYELET Eyelet 500

Combined Set

Item Code Hole Size To Suit SP Size

DEW0 5mm SP0

DEW1 6.5mm SP1

DEW3 8mm SP3

DEW4 10mm SP4

DEW6 12mm SP6

DEW7 13mm SP7

DEW9 16mm SP9

DEW20 40mm SP20

The die hammer is designed to produce maximum hitting power for all hand dies and wad punches , without damaging your tools. The two nylon hitting surfaces of the hammer are replaceable

• Recommended for use with QCD cutting pad, see page 72.


D-HU-701/SNDie Hammer to suit all hand dies/wad punches

(Not to be used with SP20)

D-H7012/R Replaceable Nylon Head each

EYELET WAD PUNCHES

DIE HAMMER

Eye

lets

94

Accessories


EYELET HAND DIES

Item Code To Suit SP Size

DEH0 SP0

DEH1 SP1

DEH3 SP3

DEH4 SP4

DEH6 SP6

DEH7 SP7

DEH9 SP9


DEH20 SP20

EYELET MACHINE CHUCKS & DIES


TOP DIE – SCREW ON with TIT Insert

DESP0 SP0

DESP1 SP1

DESP3 SP3

DESP4 SP4

DESP6 SP6

DESP7 SP7

DESP9 SP9

TIT INSERT

DET Tit Insert SP0-SP9

TOP DIE WITH 9.52mm (3/8 inch) SHAFT

DESH0 SP0

DESH1 SP1

DESH3 SP3

DESH4 SP4

DESH6 SP6

DESH7 SP7

DESH9 SP9

BOTTOM DIE WITH 9.52mm (3/8 inch) SHAFT

DEB0 SP0

DEB1 SP1

DEB3 SP3

DEB4 SP4

DEB6 SP6

DEB7 SP7

DEB9 SP9

Eyelets

Self piercing eyelet hand die

SP20 Hand Die

Eye

lets

95

Accessories


EyeletsPASKAL MULTI PRESS


PREH Paskal Multi Press - Sets Self Piercing Eyelets - Sizes SP0 to SP9 (Includes Spring)

DDSH Durable Die Shaft

DSHSEP Replacement Eyelet Screw Shaft


EYELET PRESS SPRING

DESPRING Spring

Eye

lets

Accessories - QCD Ltd

Documents