Thank you for purchasing this light fitting. Please read the
instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for
future reference.
Warning
Technical data
Please read these instructions carefully before commencingany
work.
This light fitting should be connected to a fused circuit.
The mains supply cable must have a minimum crosssectional area
of 1.0mm².
Luminaires are only suitable for mounting onnon-combustible
surfaces.
Take care not to drill into any pipes or mains cablesbeneath the
surface during mounting holes preparation.
Never put anything on the product or hang anything onany part of
this product.
This product is suitable only for dimming with 1-10V
typedimmers.
This unit must be fitted by a competent and
qualifiedelectrician.
Check the pack and make sure you have all of theparts
listed.
To prevent electrocution switch off at mains supplybefore
installing or maintaining this fitting.
Ensure other persons cannot restore the electricalsupply without
your knowledge.
Install in accordance with IEE Wiring regulations andcurrent
Building Regulations.
InstallationExisting fittings must be completely removed before
installation of a new product. Before removing the existing
fitting,carefully note the position of each set of wires. • Note
that the power needs to be isolated/switched off at the fuse
board.• The fixing point(s) selected must be capable of supporting
the full weight of the light fitting.
• Installation method 1. (Use a hook)
• Installation method 2. (Use a bracket)
• Shade installation.
• Special reminder:This lamp can be used with sensor (model no:
78577 and 78774 ).For details on sensor installation, please see
"Microwave motion sensor user's manual"
Cables must be protected using suitable conduit or
plastictrunking.
Supply
Bulb Type:
Voltage: 240V~, 50 Hz
78575--200W LED, 6500K78573--100W LED , 6500K 78574--150W LED,
6500K
The light source of this luminaire is not replaceable; when the
light source reaches its end of life the whole luminaire shall be
replaced.
Conformity with all relevant EC Directive requirements.
Waste electrical products should not be disposed of with
household waste.
Class I product, must be connected to earth.
Please recycle where facilities exist. Check with your Local
Authority orlocal store for recycling advice.
Jet-proofIP65
If replacing an existing fitting, make a careful note of
theconnections.
The Sensor and 1-10V dimmer can be used together. When the light
is 100% on, customer can use 1-10V dimmer to dim the light.When the
light is dim, customer can’t use 1-10V dimmer to dim the light.
Details wiring please refer to wiring diagram
Lampshade & Lens Accessories70° PC Reflector size
264mm
78580 78578 - 60° 78579 - 90°
90° Aluminium shade 60°/90° Lens
130mm
Ø353mm
78753
PC shade cover
78752
Ø180mm
Installation method 1.
Installation method 2.
Shade installation.
Hole dimension for mounting
Drilling a holein the ceiling,install a hook.
Hangingthe fixture
Connect the cables(See Wiring)
Fix thebracket
Drilling holes in the ceiling,and install the expansion
screws
Adjust the bracketto the beam angleyou need
1. 2. 3.
79397(use for 78574/78575)78576(use for 78573)
75mm 90mm
35m
m 35mm
1.
2. 3. 4.
Remove three screwsthrough a wrench
Lamp-chimney Lock up three screws1. 2. 3.
1.Connect the AC cables. Brown--L, Blue--N, Yellow /
Green--Ground.2.Connect the 1-10V dimmable cables. Purple--DIM+,
Gray--DIM-, Black/White--12V, (Black/White--12V is suitable for Low
Voltage Sensor)
1.Connect the AC cables. Brown--L, Blue--N, Yellow /
Green--Ground.2.Connect the 1-10V dimmable cables. Purple--DIM+,
Gray--DIM-, Black/White--12V, (Black/White--12V is suitable for Low
Voltage Sensor)
Connectthe cables(See Wiring)
NOTICE:When the light is 100% on,customer can use 1-10Vdimmer to
dim the light.When the light is dim,customer can’t use 1-10Vdimmer
to dim the light.Details wiring pleaserefer to wiring diagram.
NOTICE:When the light is 100% on, customer can use 1-10Vdimmer
to dim the light. When the light is dim, customer can’t use
1-10Vdimmer to dim the light.Details wiring please referto wiring
diagram.
AC100-240V
1-10V
LNG
DIM+
DIM-12V
AC100-240V
1-10V
LNG
DIM+
DIM-
12V