Page 1
CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.
Metra. The World’s Best Kits.® MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 1/25/18 INST99-5847CH
I N S TA L L AT I O N I N S T R U C T I O N S99-5847CH
KIT FEATURES• ISODINradioprovisionwithpocket•ISODDINradioprovision• Touchscreendisplayforclimateandpersonalizationfeatures• Integratedhazardbuttonandpassengerairbagindicator• PaintedCharcoalGrey
KIT COMPONENTS•A)Radio/Displaytrimpanelwithtouchscreendisplay•B)Radiobrackets•C)Pocket•D)(4)#8x3/8”Phillipsscrewsforpocket•E)(2)#4x1/2”PhillipsscrewsforA/CVenttoHousing•F)(2)Panelclips•G)Antennaadapter(notshown)
TOOLS REQUIRED•Panelremovaltool•Phillipsscrewdriver•9/32”Socketwrench•Torxscrewdriver
TABLE OF CONTENTS
DashDisassembly..................................................2KitPreparation....................................................... 3KitAssembly–ISODINradioprovisionwithpocket.................. 3–ISODDINradioprovision..................................... 3AxxessInterfaceInstallation............................ 4-12
WIRING & ANTENNA CONNECTIONS
WiringHarness:AxxessinterfacebuiltintotouchscreenAntennaAdapter:Included
FordExplorer(with 4.2” screen) 2011-2015
A B C D E
F
Page 2
1.800.221.0932 | MetraOnline.com2
DASH DISASSEMBLY
1. Unclipandremovethe(2)trimpanelsfromtheleftandrightsideofthefactoryradio.(FigureA)
2. Remove(4)9/32”screwssecuringtheradio/climatecontrolpaneltothedash.(FigureB)
3. Unclip,unplug,andremovethefactoryradio/climatecontrolpanel.(FigureC)
4. Remove(4)9/32”screwssecuringtheradiochassis,thenunplugandremove.(FigureD)
5. Remove(4)9/32”screwssecuringthefactorydisplay,thenunplugandremove.(FigureE)
Continue to Kit Preparation
(Figure B)
(Figure E)(Figure D)
(Figure A) (Figure C)
Page 3
REV. 1/25/2018 INST99-5847CH 3
KIT ASSEMBLYKIT PREPARATION
(Figure A)
ISO DIN radio provision with pocket
1. Securethepockettotheradio bracketsusingthe(4)#8x3/8”Phillipspanheadscrewssupplied.(FigureA)
2. RemovethemetalDINsleeveandtrimringfromtheaftermarketradio.
3. Slidetheradiobetweenradio brackets,thensecurewiththescrewssuppliedwiththeradio.(FigureA)
Continue to Axxess Interface Installation
1. Remove(2)Torxscrewssecuringthea/cventstothefactoryradio/climatecontrolpanel,thenunclipandremovethemfromthepanel.(FigureA)
2. Attachthea/cventstotheradiotrimpanelusingthe(2)#4x1/2”Phillipsscrewsprovidedwiththekit.
3. Attachthepanelclipsprovidedwiththekitontotheradiotrimpanel.Thefactoryclipsmayalsobeusedifdesired.
Continue to Kit Assembly
ISO DDIN radio provision
1. Securetheradiototheradio bracketsusingthescrewssuppliedwiththeradio.(FigureA)
Continue to Axxess Interface Installation
(Figure A)
(Figure A)
Page 4
1.800.221.0932 | MetraOnline.com4
AXXESS INTERFACE INSTALLATION
INTERFACE FEATURES
INTERFACE COMPONENTS• Axxessinterface(builtintothetouchscreendisplay)• 5847harness• 4-pinflatto4-pinstackedharness• 16-pinharnesswithstrippedleads• 12-pinbackupcameraharness• 4-pinharnesswithyellowRCAjacks• Hazardharness• Female3.5mmconnectorwithstrippedleads
TOOLS REQUIRED•Wirecutter•Crimptool•Soldergun•Tape•Connectors(example:butt-connectors,bellcaps,etc.)
TABLE OF CONTENTS
Connectionstobemade...........................................................................................................5-6Installingtheinterface................................................................................................................. 7Initializingtheinterface............................................................................................................... 8Finalassembly.............................................................................................................................. 8Extrafeatures(SYNC).................................................................................................................... 8Touchscreendisplayoperation............................................................................................... 9-10Steeringwheelcontrolsettings............................................................................................. 11-12
• Providesaccessorypower(12-volt10-amp)• RetainsR.A.P.(retainedaccessorypower)• ProvidesNAVoutputs(parkingbrake,reverse,speedsense)• Retainsaudiocontrolsonthesteeringwheel• RetainsSYNC®
• Retainsthefactorybackupcamera• Retainsbalanceandfade• Micro“B”USBupdatable
Page 5
REV. 1/25/2018 INST99-5847CH 5
CONNECTIONS TO BE MADE
From the 5847 harness to the aftermarket radio:
• ConnecttheBlackwiretothegroundwire.
• ConnecttheYellowwiretothebatterywire.
• ConnecttheGreenwiretotheleftrearpositivespeakeroutput.
• ConnecttheGreen/Blackwiretotheleftrearnegativespeakeroutput.
• ConnectthePurplewiretotherightrearpositivespeakeroutput.
• ConnectthePurple/Blackwiretotherightrearnegativeoutput.
• Tapeoffanddisregardthefollowing(1)wire,itwillnotbeusedinthisapplication:Blue
• For models with SYNC®:ConnecttheRedandWhiteRCAjackslabeled“RSE/SYNC/SAT”totheaudioAUX-INjacksoftheaftermarketradio.
• For models without SYNC®:ConnecttheRedandWhiteRCAjackslabeled“FROM3.5”totheaudioAUX-INjacksoftheaftermarketradio.
• DisregardtheDINjack,itwillnotbeusedinthisapplication.
Continued on the next page
From the 16-pin harness with stripped leads to the aftermarket radio:
• Connectthe(2)Redwirestotheaccessorywire.
• Ifequippedwithafactorysubwoofer,connecttheBlue/Whitewiretotheampturnonwire.
• Iftheaftermarketradiohasanilluminationwire,connecttheOrange/Whitewiretoit.
• Iftheaftermarketradiohasamutewire,andthevehicleisequippedwithSYNC®,connecttheBrownwiretoit.Ifthemutewireisnotconnected,theradiowillturnoffwhenSYNC®isactivated.
• ConnecttheGraywiretotherightfrontpositivespeakeroutput.
• ConnecttheGray/Blackwiretotherightfrontnegativespeakeroutput.
• ConnecttheWhitewiretotheleftfrontpositivespeakeroutput.
• ConnecttheWhite/Blackwiretotheleftfrontnegativespeakeroutput.
• Tapeoffanddisregardthefollowing(4)wires,theywillnotbeusedinthisapplication:Green,Green/Black,Purple,Purple/Black
The following (3) wires are only for multimedia/navigation radios that require these wires.
• ConnecttheBlue/PinkwiretotheVSS/speedsensewire.
• ConnecttheGreen/Purplewiretothereversewire.
• ConnecttheLight Greenwiretotheparkingbrakewire.
Page 6
1.800.221.0932 | MetraOnline.com6
CONNECTIONS TO BE MADE (CONT.)
12-pin backup camera harness:
For models with a 4.2-inch display screen:
• Usethe12-pinbackupcameraharness.
There are two different methods for connecting the factory backup camera.
If retaining the camera to the aftermarket radio is desired:
• ConnecttheYellowRCAjackthebackupcamerainputoftheaftermarketradio.
If retaining the camera to the touchscreen display is desired:
• ConnecttheYellowRCAjack,totheYellowRCAjackfromthe4-pinharnesswithyellowRCAjackslabeled“Rearviewcamera”.
Note:If this method is chosen, the backup camera option must be enabled in the Configuration Settings Screen.
4-pin harness with yellow RCA jacks:
• Ifretainingthefactorybackupcameratothetouchscreendisplayisdesired,connecttheYellowRCAjacklabeled“Rearviewcamera”,totheYellowRCAjackfromthe12-pinor54-pinbackupcameraharness.
• DisregardtheYellowRCAjacklabeled“AUXvideo”,itwillnotbeusedinthisapplication.
3.5mm jack steering wheel control retention:
• The3.5mmjackistobeusedtoretainaudiocontrolsonthesteeringwheelcontrol.
• Fortheradioslistedbelow,connecttheincludedfemale 3.5mm connector with stripped leads,tothemale3.5mmSWCjackfromthe5847harness.Anyremainingwirestapeoffanddisregard:
• Eclipse:Connectthesteeringwheelcontrolwire,normallyBrown,totheBrown/Whitewireoftheconnector.Thenconnecttheremainingsteeringwheelcontrolwire,normallyBrown/White,totheBrownwireoftheconnector.
• Metra OE:ConnectthesteeringwheelcontrolKey1wire(Gray)totheBrownwire.
• Kenwood or select JVC with a steering wheel control wire: ConnecttheBlue/YellowwiretotheBrownwire.
Note:If your Kenwood radio auto detects as a JVC, manually set the radio type to Kenwood. See the instructions under changing radio type.
• XITE:ConnectthesteeringwheelcontrolSWC-2wirefromtheradiototheBrownwire.
• Parrot Asteroid Smart or Tablet:Connectthe3.5mmjackintotheAX-SWC-PARROT(soldseparately),andthenconnectthe4-pinconnectorfromtheAX-SWC-PARROTintotheradio.
Note:The radio must be updated to rev. 2.1.4 or higher software.
• Universal “2 or 3 wire” radio:Connectthesteeringwheelcontrolwire,referredtoasKey-AorSWC-1,totheBrownwireoftheconnector.Thenconnecttheremainingsteeringwheelcontrolwire,referredtoasKey-BorSWC-2,totheBrown/Whitewireoftheconnector.Iftheradiocomeswithathirdwireforground,disregardthiswire.
Note:After the interface has been programmed to the vehicle, refer to the manual provided with the radio for assigning the SWC buttons. Contact the radio manufacturer for more information.
• For all other radios:Connectthe3.5mmjackintotheportontheradiodesignatedforanexternalsteeringwheelcontrolinterface.Refertothemanualprovidedwiththeradioifindoubtastowherethe3.5mmjackgoesto.
Page 7
REV. 1/25/2018 INST99-5847CH 7
INSTALLING THE INTERFACE
Itishighlyadvisabletoreadthefollowingstepsbeforehand,toensureaclearunderstandingofwhatistobeexpected.Thefollowingstepsmustbedoneintheorderthattheyarenumbered.
With the vehicle completely off:
1. Connectthe16-pin harness with stripped leadsintoport“B”inthetouchscreendisplay.
2. Connectthe5847 harnesstothewiringharnessesinthevehicle.Theseharnessesaretheonesremovedinstep4ofdashdisassembly.Theninsertthe5847 harnessintoport“A”inthetouchscreendisplay.Butdonotinstallthisharnessuntilexactlybeforestep1of“InitializingtheInterface”.Thisisatimedprocess.
3. Connectthe4-pin harness with yellow RCA jacksintoport“C”inthetouchscreendisplay.
4. Connectthehazardharnessintoport“D”inthetouchscreendisplay,thentothewiringharnessinthevehicle.Thisistheharnessremovedinstep3ofdashdisassembly.
5. Disregardport“E”,itwillnotbeusedinthisapplication.
6. Port“F”isanupdateportforfuturefirmwareupgrades.
A BC
EF D
Page 8
1.800.221.0932 | MetraOnline.com8
INITIALIZING THE INTERFACE FINAL ASSEMBLY
1. Securethecompletedassemblyintothedashusingthefactoryhardware.
2. Snaptheradio trim panelwithtouchscreen displayoverthecompletedassembly,andthenreassemblethedashinreverseorderofdisassembly.
Attention!Iftheinterfacelosespowerforanyreason,thefollowingstepswillneedtobeperformedagain.
1. Refertostep2of“Installingtheinterface”.
2. Placethevehicleignitiontotheonposition.
3. Programthekit:
a. Oncethetouchscreendisplayloadsup,selectthevehicletype;“FordExplorer2011-2015”.
b. Waituntiltheradiocomeson,andthetouchscreendisplayshows“SWCConfigured*”.Thisprocessmaytakeupto3minutes.
Note:If the touchscreen display does not load up, or the radio doesn’t come on within 3 minutes, and/or the touchscreen display does not show “SWC Configured*”, turn the vehicle off and disconnect the harness from port “A” in the touchscreen display. Check all the connections, reconnect the harness into the touchscreen display, and then try again.
*Formodelswithsteeringwheelcontrols.
4. Testallfunctionsoftheinstallationforproperoperation,beforereassemblingthedash.
SYNC:
IfthevehicleisequippedwithSYNC,the99-5847CHcanretainthisfeature.
• ChangethesourceoftheradiotoAUX-IN.
• Pressthe“Info”buttononthetouchscreendisplaytoentertheSYNCmenu.Pressthe“HVAC”buttontogetbacktothemainmenu.
EXTRA FEATURES
Page 9
REV. 1/25/2018 INST99-5847CH 9
TOUCHSCREEN DISPLAY OPERATION
• ThisistheHVACcontrolscreenwhichwillbedisplayedonthetouchscreendisplay.Thisisconsideredthemainscreen.
• Theupperlefttabwith(3)arrowswilltakeyoutotheHeated/Cooledseatsscreen,ifapplicable.
Note:This screen will also include Heated Steering if applicable.
• TheupperrighttabwiththegeariconwilltakeyoutotheConfiguration Settingsscreen.
• Auto climate models:Theclimatecontrolswillfunctioninthesamemannerthattheydidwiththefactoryclimatecontrols.
• Manual climate models:Theclimatecontrolswillfunctioninthesamemannerthattheydidwiththefactoryclimatecontrols,yetviatouchscreenbuttonsinstead.Thetemperaturecontrolwilldisplayanumericalscale,with“LO”beingthecoldest,and“HI”beingthehottest:LO/1-9/HI
Note: The “Info” button will only be shown if SYNC is to be retained.
Continued on the next page
HVAC Control screen
Manualclimatecontrols
Automaticclimatecontrols
Page 10
1.800.221.0932 | MetraOnline.com10
TOUCHSCREEN DISPLAY OPERATION (CONT.)
Configuration Settings screen
• Backlight
•Fourslidebarscontrolthecolorofthebuttonsandtheback-lightintensity: Red/Green/Blue/Backlight
• Backup Camera
•Enable–Enablesthebackupcameraimagetothetouchscreendisplay
•Disable–Disablesthebackupcameraimagetothetouchscreendisplay(default)
• Steering Wheel Controls
•RemapButtons–Forremappingthesteeringwheelcontrolbuttons
•DualAssign–Fordualassigningthesteeringwheelcontrolbuttons(longbuttonpress)
•SelectRadio–Forautodetectingtheradio,orchangingtheradiotype
Touchscreen calibration
• Pressandholdtheuppertwosoftbuttonsoneithersideofthetouchscreenfor10seconds.
• Ascreenwillpopupaskingforyoutopressthetargetinthescreen.
• Afterpressingthetargetwithyourfinger,thecalibrationprocesswillbecomplete,andthescreenwilldisappear.
Page 11
REV. 1/25/2018 INST99-5847CH 11
STEERING WHEEL CONTROL SETTINGS
Select Radio screen
* Note: If the interface shows an Alpine radio, and you do not have an Alpine radio, that means the interface does not detect a radio connected it, i.e., an open connection. Verify that the 3.5mm jack is connected to the correct steering wheel jack/wire in the radio.
** Note: The AX-SWC-PARROT is required (sold separately). Also, the Parrot radio must be updated to rev. 2.1.4 or higher through www.parrot.com.
† Note: If you have a Clarion radio and the steering wheel controls do not work, change the radio type to the other Clarion radio type; same for Eclipse.
‡ Note: If you have a Kenwood radio and the touchscreen display shows a JVC radio, change the radio type to Kenwood.
Continued on the next page
Eclipse(Type1)†
Kenwood‡
Clarion(Type1)†
Sony/Dual
JVC
Pioneer/Jensen
Alpine*
Visteon
Valor
Clarion(Type2)†
MetraOE
Eclipse(Type2)†
LG
• Toshowwhichbrandradiois“autodetected”totheinterface,pressthe“Autodetect”button.Theradiodetectedwillhaveafilledincircle.Iftheincorrectradioisshown,selecttheproperradio.
• Followingisalistofradiomanufacturersthattheinterfacepresentlyacknowledges.Othersmaybeaddedatalaterdate.Universal“2or3wire”radioscanshowupasanyoftheseradiomanufacturers.
Parrot**
XITE
Philips
JBL
Page 12
1.800.221.0932 | MetraOnline.com12
STEERING WHEEL CONTROL SETTINGS (CONT.)
Remap Button screen Dual Assign screen
• Theinterfacehastheabilitytochangethebuttonassignmentforthesteeringwheelcontrolaudiobuttons,exceptVolume-UpandVolume-Down.Followthepromptsonthetouchscreendisplaytoremapthesteeringwheelcontrolaudiobutton(s)toyourliking.
Note: The aftermarket radio may not have all of these commands. Please refer to the manual provided with the radio, or contact the radio manufacturer, for specific commands recognized by that particular radio.
• Theinterfacehasthecapabilitytoassigntwofunctionstoasinglebutton,exceptVolume-UpandVolume-Down.Followthepromptsonthetouchscreendisplaytoprogramthebutton(s)toyourliking.
Note: Seek-Up and Seek-Down come programmed as Preset-Up and Preset-Down for a long button press.
Page 13
REV. 1/25/2018 INST99-5847CH 13
Page 14
1.800.221.0932 | MetraOnline.com14
Page 15
REV. 1/25/2018 INST99-5847CH 15
Page 16
KNOWLEDGE IS POWEREnhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
®
Metra recommends MECP certified technicians
IMPORTANTIf you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.
Metra. The World’s Best Kits.® MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 1/25/18 INST99-5847CH
I N S TA L L AT I O N I N S T R U C T I O N S99-5847CH