Distributed by Mueller Streamline Co. • 8285 Tournament Drive, Memphis, TN 38125 • 800-348-8464 • www.muellerindustries.com page 1 of 7 Product Description: Streamline ® ABS DWV ittings for use in applications including sanitary drain, waste, and vent (DWV), sewer, and general drainage applications. Available in sizes ranging from 1-1/4” to 6” in diameter, all ittings should be manufactured in the United States. Material: Acrylonitrile-butadiene-styrene (ABS) DWV ittings shall conform to cell class 3-2-2-2-2 as deined in ASTM 3965. Key Speciications: Streamline ® ABS DWV ittings shall conform to ASTM D2661 and F1498. Third-party certiications shall be in place for ittings in compliance with NSF Standard 14. Fittings shall be certiied to the Uniform Plumbing Code (UPC) where applicable. Installation: Installation shall comply with the latest applicable building codes for the local jurisdiction. Solvent cement connections shall be made using a two-step process consisting of primer (in conformance with ASTM F656) and solvent cement (in conformance with ASTM D2564). For detailed installation instructions, consult the Plumbing Apprentice Training Manual available from PPFA (Plastic Pipe & Fitting Association) at ppfahome.org. ABS DWV ittings are not designed for hot water systems and discharge temperatures should not exceed 140°F. Systems shall be installed to avoid contact with thread sealants or other chemical agents which are not compatible with ABS. Hydrostatic testing of the system shall be completed prior to use. Do not test or use Streamline ® plastic products with compressed air or compressed gases. References: ASTM 3965 Classiication for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Tube and Fittings ASTM D2661 Standard Speciication for ABS Drain, Waste, and Vent Fittings ASME F1498 Taper Pipe Threads for Thermoplastic Fittings/Fitting Threads ASTM F656 Standard Speciication for Primers ASTM D2564 Standard Speciication for Solvent Cement Other Applicable Standards: NSF Standard 14 Plastic Piping System and Related Components NSF International IAPMO UPC ABS DWV FITTINGS FOR PLUMBING AND MECHANICAL APPLICATIONS Job Name Contractor Job Location Wholesaler Engineer Streamline ® Rep MADE IN USA
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Distributed by Mueller Streamline Co. • 8285 Tournament Drive, Memphis, TN 38125 • 800-348-8464 • www.muellerindustries.com page 1 of 7
Product Description:
Streamline® ABS DWV ittings for use in applications including sanitary drain, waste, and vent (DWV), sewer, and general drainage
applications. Available in sizes ranging from 1-1/4” to 6” in diameter, all ittings should be manufactured in the United States.
Material:
Acrylonitrile-butadiene-styrene (ABS) DWV ittings shall conform to cell class 3-2-2-2-2 as deined in ASTM 3965.
Key Speciications:
Streamline® ABS DWV ittings shall conform to ASTM D2661 and F1498. Third-party certiications shall be in place for ittings in
compliance with NSF Standard 14. Fittings shall be certiied to the Uniform Plumbing Code (UPC) where applicable.
Installation:
Installation shall comply with the latest applicable building codes for the local jurisdiction. Solvent cement connections shall be made
using a two-step process consisting of primer (in conformance with ASTM F656) and solvent cement (in conformance with ASTM
D2564). For detailed installation instructions, consult the Plumbing Apprentice Training Manual available from PPFA (Plastic Pipe &
Fitting Association) at ppfahome.org.
ABS DWV ittings are not designed for hot water systems and discharge temperatures should not exceed 140°F. Systems shall be
installed to avoid contact with thread sealants or other chemical agents which are not compatible with ABS. Hydrostatic testing of
the system shall be completed prior to use.
Do not test or use Streamline® plastic products with compressed air or compressed gases.
References:
ASTM 3965 Classiication for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Tube and Fittings
ASTM D2661 Standard Speciication for ABS Drain, Waste, and Vent Fittings
ASME F1498 Taper Pipe Threads for Thermoplastic Fittings/Fitting Threads
ASTM F656 Standard Speciication for Primers
ASTM D2564 Standard Speciication for Solvent Cement
Other Applicable Standards:
NSF Standard 14 Plastic Piping System and Related Components
NSF International IAPMO
UPC
ABS DWV FITTINGS FOR PLUMBING AND
MECHANICAL APPLICATIONS
Job Name Contractor
Job Location Wholesaler
Engineer Streamline® Rep
MADE IN USA
Distributed by Mueller Streamline Co. • 8285 Tournament Drive, Memphis, TN 38125 • 800-348-8464 • www.muellerindustries.com page 2 of 7
1 1/2 x 1 1/2 x 1 1/4 02757 20 2,1601 1/2 x 1 1/4 x 1 1/2 02762 20 2,1601 1/2 x 1 1/4 x 1 1/4 02759 20 1,440 2 x 1 1/2 x 1 1/2 02761 25 1,3502 x 1 1/2 x 2 02760 25 1,2002 x 2 x 1 1/2 02758 50 1,2003 x 3 x 1 1/2 02764 20 6403 x 3 x 2 02763 10 4804 x 4 x 2 02765 10 280 4 x 4 x 3 02766 10 1806 x 6 x 4 02768 6 72
STYLE NO. A429 DOUBLE SANITARY TEE, REDUCING ALL HUB
Size Part # Ctn Plt
2 x 2 x 1 1/2 x 1 1/2 02817 20 840 3 x 3 x 1 1/2 x 1 1/2 02818 20 4803 x 3 x 2 x 1 1/2 02819 10 3603 x 3 x 2 x 2 02820 10 3604 x 4 x 2 x 2 02240 5 2404 x 4 x 3 x 3 02821 5 160
STYLE NO. A431DOUBLE SANITARY TEE, STREET, REDUCINGSP x H x H x H
Size Part # Ctn Plt
3 x 3 x 2 x 2 03310 10 360
STYLE NO. A438 DOUBLE SANITARY TEE W / SIDE INLETALL HUB
Size Part # Ctn Plt
3 x 3 x 3 x 3 x 2 02772 10 180
STYLE NO. A439 DOUBLE SANITARY TEE W / RIGHT & LEFT SIDE INLET ALL HUB
Size Part # Ctn Plt
3 x 3 x 3 x 3 x 2 x 2 02770 10 180
STYLE NO. A441VENT TEE
ALL HUB
Size Part # Ctn Plt
1 1/2 03403 25 1,800
2 03404 25 1,350
3 03405 10 480
4 03406 5 180
Distributed by Mueller Streamline Co. • 8285 Tournament Drive, Memphis, TN 38125 • 800-348-8464 • www.muellerindustries.com page 6 of 7
STYLE NO. A502COMBINATION WYE & 1/8 BEND, REDUCING - ONE PIECE ALL HUB
Size Part # Ctn Plt
2 x 1 1/2 x 1 1/2 02835 5 5402 x 1 1/2 x 2 02836 5 5402 x 2 x 1 1/2 02865 20 8403 x 3 x 1 1/2 02837 15 4803 x 3 x 2 02857 10 3604 x 4 x 2 02863 5 1804 x 4 x 3 02864 5 120
STYLE NO. A503 COMBINATION WYE & 1/8 BEND – TWO PIECE ALL HUB
Size Part # Ctn Plt
6 02266 2 24
STYLE NO. A504 COMBINATION WYE & 1/8 BEND, REDUCING - TWO PIECE ALL HUB
2 x 1 1/2 x 1 1/2 02831 25 1,200 2 x 1 1/2 x 2 02832 10 7202 x 2 x 1 1/2 02826 25 1,0503 x 3 x 1 1/2 02827 15 4203 x 3 x 2 02828 25 4004 x 4 x 1 1/2 02833 5 210 4 x 4 x 2 02829 10 2404 x 4 x 3 02830 10 160 6 x 6 x 4 03137 5 60
2 x 2 x 1 1/2 x 1 1/2 02847 10 720 3 x 3 x 1 1/2 x 1 1/2 02843 10 360 3 x 3 x 2 x 2 02844 10 280 4 x 4 x 2 x 2 02845 5 180 4 x 4 x 3 x 3 02846 5 90 6 x 6 x 4 x 4 03142 3 54