Charles MacBride, AIA, Associate Professor SDSU DoArch Robert Arlt, AIA, CPHC, Instructor SDSU DoArch A statewide initiative: The expanding influence of Passive House in South Dakota
Charles MacBride, AIA, Associate Professor SDSU DoArch Robert Arlt, AIA, CPHC, Instructor SDSU DoArch
A statewide initiative: The expanding influence of Passive House in South Dakota
A statewide initiative: The expanding influence of Passive House in South Dakota
• Introduction PHIUS and SD Initiatives 1 Prototype Governor’s House and the role of SDHDA 2 CPHC sponsored training to AIA South Dakota 3 Copper Pass pilot multifamily affordable housing, Sioux Falls SD 4 PH01:BRK SDSU student designed single family house, Brookings SD
A statewide initiative: the expanding influence of Passive House in South Dakota
1 Prototype Governor’s House / income-qualified & pre-fab
2 CPHC sponsored training / professional community
3 Copper Pass / multifamily affordable housing
4 PH01:BRK / educating architecture students
While it isn’t an excuse, it is important to remember that design and construction in the region is entrenched in the known. There is little financial or cultural incentive for change or innovation.
1 Prototype Governor’s House and the role of the South Dakota Housing Development Authority (SDHDA)
A statewide initiative: the expanding influence of Passive House in South Dakota
Prototype Governor’s House Design & fabrication 2013 PHPP pre-certification (attempted) Installed, Britton, SD 2016 PHIUS+ certification 2017
DN
UP
N
12'-11"
57'-5 3/8"
33'-9 15/16"
25'
3'-1 1/16"
25'-7"
11'-7"
2'
12'
6'-6"
5'-1"
43'-7"
18'-11"
9'-3"
15'-5"
13'-1"
5'-10"4'-0 1/4"
5'-2 3/4"
25'-7"
6'-4 1/2"
19'-2 1/2"
15'-6"
3'-8 1/2"
43'-7"
13'-0 1/2"
2'-4 1/2"
2'-11 1/2"
25'-2 1/2"
3'-8 1/2"
6'-10"
3'-4"
3'-4"
8'
8'-1"
4'-11 1/2"
9'-4"
5'-1 1/2"
4'-2"
5'-0 1/4"
10'-9"
8'
5'-8 1/2"
2'-1"
7'-10 1/2"
2'-8"
3'-7"
2'-8"
2'-8"
14'-2"
11'-11 1/2"
5'-5 1/2"
5'
14'-2"
9'-5"
10th
Ave
nue
12th Street
Lot 4 Kadoun Subdivision Britton, SD
DN
D/W
WH
REF.
UP
12'-0" x 12'-4"
11'-9" x 10'-8"
14'-1" x 9'-10"
8'-11" x 7'-11"
2'-7
" x 5
'-8"
17'-0" x 10'-3"
2'-0
" x 4
'-11"
23'-8" x 3'-2"
25'-7
"
11'-7
"2'
12'
6'-6
"5'
-1"
43'-7"
18'-11"9'-3"15'-5"
13'-1"5'-10"4'-0 1/4"5'-2 3/4"
25'-7
"
6'-4
1/2
"19
'-2 1
/2"
15'-6
"3'
-8 1
/2"
43'-7"
13'-0 1/2" 2'-4 1/2" 2'-11 1/2" 25'-2 1/2"
3'-8 1/2" 6'-10" 3'-4" 3'-4" 8'8'-1" 4'-11 1/2"
BEDROOM
BEDROOM
CLO
SET
BATH
LAU
ND
RY
KITCHEN
LIVING
DECK
DES
IGN
BY:
3/13
/201
5
Gov
erno
r's H
ouse
Pro
gram
Pass
ive
Hou
se B
ritt
on
4
Governors House ProgramPassive House Britton
Main Floor 1/4"=1'
Logix Block ICF foundation wall2 1/2" EPS, 6” concrete, 2 1/2" EPS
1x Furring
1/2" Drywall
1/2" Gypsum Drywall
8" Poly IsocynurateStaggered and taped
Architectural Shingles15/32 OSB Sheathing
Synthetic Felt
Prefinished Metal Fascia
3/4" OSB Subfloor
18" Floor Truss
Baffle
Prefinished Aluminum Soffit
1/4" OSB Blocking
R-21 High Perfm. Fiberglass batt
2" Extruded Polystyrene
R-84 Cellulose
4" Extruded Polystyrenestaggered and taped
7/16" OSB Air BarrierTaped & Sealed
2x4 furred down ceiling with R13 F.G Batts
2 CPHC sponsored training to AIA South Dakota
2016 SDHDA / AIA SD participants: Patri Acevedo, AIA, CPHC, JLG I AcV2 Architects Robert Arlt, AIA, CPHC, Instructor SDSU DoArch Alison Dvorak, AIA, CPHC, Koch Hazard Architects Andrew Fett, AIA, CPHC, LEED AP, Williams & Associates Herm Harms, AIA, CPHC, Puetz Corporation Katie Krantz, AIA, CPHC, VanDeWalle Architects Jason Roberdeau, AIA, CPHC, Williams & Associates
Other SD CPHC Mike Harsma, CPHC, Director SDHDA Governors House Program Aspen Greene, CPHC, Graduate Student SDSU DoArch Emily Nelsen, CPHC, 2016 Graduate SDSU DoArch
A statewide initiative: the expanding influence of Passive House in South Dakota
A statewide initiative: the expanding influence of Passive House in South Dakota
from follow-up interviews:
Descriptions of projects that, for example, call for “a greater air-tightness or thermal envelope than usual, and then are changed ‘back to normal’ in the field” without knowledge of the architect are alarmingly common.
Other examples of municipal reviewers “waiving a nominal energy requirement for the financial benefit of developers and builders” seems standard.
A discussion of various contractor’s own interests and abilities ranged from excellent to unintelligible: one “questioned the entire topic of building science and the usefulness of knowing where the dew point falls in a wall assembly.”
3 Copper Pass pilot multifamily affordable housing, Sioux Falls SD
A statewide initiative: the expanding influence of Passive House in South Dakota
Copper Pass Affordable Housing Design & construction 2016-18 PHIUS+ pre-certification, 2017 (in-progress)
• SDHDA pilot Passive House affordable housing project • Architect: VanDeWalle Architects LLC • Developer: Costello Co. • General Contractor: BlackWing Elite Builders • Project Goals:
• Achieve Passive House certification • Build sister project to ENERGY STAR certification • Compare and analyze construction costs, operating
costs, and performance data of both projects • Originally 24 units; added 6 more when costs came in
under budget
Copper Pass Affordable Housing
Footing and Foundation Design
• Wanted to keep it conventional as possible
• Typical spread footing with 4’ foundation wall
• 3” of high density XPS under footing • Entire foundation wall wrapped with
3” of EPS • 4” of EPS under entire slab
Copper Pass Affordable Housing
Wall Assembly
• Typical 2x6 stud cavity • R-Max panels for
continuous insulation • Thin Brick & James Hardie
siding
Copper Pass Affordable Housing
Roof & Parapets
• Roof = R-75 • 24” roof trusses, blown full • SIPs above corridor • R-49 above roof sheathing • Boxed parapets outside air barrier • No ductwork in roof truss cavity
Mechanical System
• Energy Recovery Ventilator – zoned by floor. • Fresh Air Ducted to each bedroom. • Filtered Exhaust from kitchens. • Duct-free Mini-split System – one per apartment. • Condensing Dryers. • Low-flow plumbing Fixtures.
Copper Pass Affordable Housing
Footing & Foundation Wall
Copper Pass Affordable Housing
Slab Insulation & Vapor Barrier
4 PH01:BRK SDSU student designed single family house, Brookings SD
A statewide initiative: the expanding influence of Passive House in South Dakota
PH01:BRK Student design, fall 2016 PHIUS+ pre-certification, 2017 Construction, Brookings, SD 2017-18
1 ENTRY2 LIVING ROOM3 DINING ROOM4 KITCHEN5 MUDROOM6 BATHROOM7 LAUNDRY8 MASTER SUITE9 LOFT10 MECHANICAL11 BEDROOM12 COURTYARD13 GARAGE
23
46
8
5
7
6
11
119
10
1
13
12
www.sdstate.edu/architecture/south-dakota-passive-house-project
Scale
Project number
Date
Issue
PHO1:BRKThe South Dakota Passive Housing Initiative
Brookings, SD
South Dakota State University Department of Architecture
In collaboration withFB&T Community Development Corp.
Funded through a grant from the Governor's Office of Economic Development
Phone: (605) 688-4841
1/16" = 1'-0"
L2-1
PROPOSED SITE PLAN
PHIUS+ Project # 1415
05-05-2017prelim / zoning variance
Not For Construction
PROPOSED TWO-STORY PASSIVE HOUSE
SINGLE FAMILY RESIDENCE
PROPOSED DETACHED
GARAGE
PRIVATE DRIVEWAY (FIRST LUTHERAN CHURCH)
9TH STREET
3RD
AVEN
UE
ALLEY
LOT 7A
LOT 5A
LOT 6A
7' EA
SEME
NT
PROPOSED DRIVEWAY (10' WIDTH) 7' SIDE SETBACK
7' SIDE SETBACK
25' F
RONT
SET
BACK
25' R
EAR
SETB
ACK
N89˚30'54"W 176.1' (176.0 REC.)
51'-6" +/- HOUSE
28'-6
" +/-
HOUS
E
PROPOSED SITE PLAN PH01:BRK / PASSIVE HOUSE BROOKINGS 1" = 16'-0"
SIDE
WAL
K
LOT 7A (street address to be assigned) 3rd Avenue Brookings, SD 57006 lat: 44˚18'57"N lon: 96˚48'00"W elevation: 1642' declination: 3˚7'E LEGAL DESCRIPTION: LOTS 5A, 6A, AND 7A OF PARKDALE HOME ADDITION, BEING A REPLAT OF LOTS 5, 6, AND 7 AND THE NORTH 8 FEET OF LOT 8 OF PARKDALE HOME ADDITION, CITY OF BROOKINGS, BROOKINGS COUNTY, SD. ZONING: R-2 / Residence R-2 Two-Family District Note: The lots were replatted following a sub-division in Nov. 2016. The two "narrow" lots (6A and 7A) as approved do not meet the established R-2 zoning for minimum lot width.
PARKING AREA (FIRST LUTHERAN CHURCH)
N89˚30'55"W 176.1'
N00˚
00'00
"W 4
8.5'
N00˚
03'29
"E 4
8.5'
1'-0" 17'-0" 24'-0" GARAGE
6"5'-
6"
3'-0"
FIXED SUN-SHADING CANOPY 9'-6"+/- HT ABOVE GRADE
7'-0"
1'-0"
5'-0"
1'-6"
COURTYARDENTRY
BACK ENTRY
7'-0"
24'-0
" GA
RAGE
4'-6"LARGE EAVE
BACK-UP SPACE
BACK CANOPY
ENTRY SIDEWALK
1. roof assembly:thermal bridge free to .006 btu/hrft2f024 ga. standing seam metal roofing reverse board battens (1x3 over 2x4)5/8" zip sheathing taped and sealed waterproofing24" open web joists infill with knauff mineral wool 1/2" osb taped and sealed 2x2 wood blocking 16" o.c. for electrical chase1/2" maple/birch veneer plywood
2. south wall:frame out on south wallhardieplank1/2" celotex sheathing24" wood i-joist filled with knauff mineral wool
3. built in gutter slope 1/4" per ft4. 12 " type ix eps foam insulation density=1.80 pcf,
Rvalue = 5.00 per 1"5. 4" pea rock6. taped and sealed around block at top of wall7. wall assembly:
thermal bridge free to .006 btu/hrft2f09.25" hardie board horiz. siding2 1/2" insofast 6" eps foam insulation
1
1.13 Vertical cross section
3
6
13
14
17
15
6" eps foam insulation 7/16" zip sheating taped and sealed 2x6 w/ infill knaupf mineral wool insulation 1/2" gwb finish
8. slab assembly:thermal bridge free to .006 btu/hrft2f0engineered backfill 12" eps foam insulation seams taped and sealed10" compacted filltaped polyethylene water and vapor barrier 6" reinforced concretemaple floor over 3/4" ply
9. 14" wood open web joist see struct.10. w flange beam11. gwb continues past flange12. 2x3 railing 5" o.c.13. clerestory polycarbonate. note: same detail turns
corner and terminates at ceiling line14. ridge vent15. ridge beam. note: tape and seal osb air barrier to
glulam beam.16. 3' 2" thick eps frost skirt17. osb sheathing continues on top of plate to inside
to tape and seal to ceiling osb to maintain continous air barrier.
5
2
4
7
8
9 1011
12
16
1.18 Vertical section South wall
1. 9.25" hardieplank installed over insofast
2. floor/ roof assembly (R-75):
cedar Soffit- 1x4 T&G
inSoFast Insulation- 2 1/2" (R-10.5)
6" EPS Insulation- (R-4.17/in. = R-33.36)
zip roof sheathing system- 5/8" (vapor/air
permeable)
18" Wood Web Joist Truss- 16" O.C.
11" Blown-In Insulation- Glass Mineral Wool
(R-2.8/in. = R-31)
1/2" OSB Sheathing- Taped & Sealed (Vapor/Air
Barrier)
Floor Finish per Room Finish Schedule
3. 3ply 18" LVL
1
2
3
• challenges moving forward
1 Capitalize on the initial burst of activity and
keep the momentum.
A statewide initiative: the expanding influence of Passive House in South Dakota
• challenges moving forward
2 Continued financial and political support from
the state is necessary…the expectation that the
construction industry will move towards higher
standards without incentive or regulation is
naïve.
A statewide initiative: the expanding influence of Passive House in South Dakota
• challenges moving forward
3 The lack of serious building or energy code
implementation is a barrier…the ‘regulatory’
smell of codes is a cultural and political
obstacle that hinders the advancement of
building science.
It is the architect’s responsibility to raise
expectations, from both the state and the
construction industry.
A statewide initiative: the expanding influence of Passive House in South Dakota
• challenges moving forward
4 The continued support of subsidized housing
must be maintained if not increased.
A statewide initiative: the expanding influence of Passive House in South Dakota
The investment by the state over the past four
years into Passive House is a remarkable legacy,
but one that still needs critical, positive
investment.
It is our hope that the exponential growth of
Passive House nationally will encourage South
Dakota to stay the course.
Thank you!
A statewide initiative: the expanding influence of Passive House in South Dakota