A-FRAME FLY FORM (FLOOR SUPPORTED) • Used for supporting cast-in-place concrete slabs in high-rise con- struction • Flexible and time saving system • Fully adaptable to the configuration and shor- ing height of a slab • Much lighter and cost effective compared to conventional trusses ATLAS-SALES.COM | (808) 841-1111 Typical A-Frame Fly Form Cycle Fly Form Table is placed on top of previously poured floor slab. Fly Form Table supports newly poured concrete slab When concrete reaches required strength and EOR approves strip, Table is lowered from pured slab and rolled towards from building to connect to the crane The Fly Form Table is lifted by crane and flown out of the building to new level on top of the recently poured concrete slab. 1 4 3 2 Hokua Ko ‘Olina Moana Pacific Ko ‘Olina
16
Embed
A-FRAME FLY FORM (F S - irp-cdn.multiscreensite.com · with formwork being an integral part of the A-Frame Fly Form table ... Slab over the slab below ... The main horizontal support
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
UseUsed to extend height of standard truss table legs to reach greater heights
33-50” addition to standard table legsCustom item. Requires cross brace (x2) for stability.
TRUSS EXTENSION LEG ASSEMBLY A070601 32LB
8
ATLAS FLY FORM SYSTEM
ATLAS-SALES.COM | (808) 841-1111
A-FRAME FLY FORM
A
B
C
D
H
GF
E
I
H
J
K, L, M
Use Notes/ObservationsAdjustable jack for Fly Form system. The hinged jack truss comes fully assembled with all these parts
Can be positioned at various locations on the bottom chord (H-750) and inter-changed to accommodate different floor to floor heights. Hinged feature assures easy installation and removal. Variations in body and screw length allow for the various truss jack lengths.
HINGED TRUSS JACK COMPONENTSATRUSSJACKTOPCASTING 7074010 6.76LB
BTRUSSJACKBASECASTING 7074020 4.31LB
CTRUSSJACKBODY VARIES
D TRUSSJACKBASESCREW VARIES
ETRUSSJACKRETAINERRING 7074090 .2LB
F TRUSSJACKRETAINERBRACKET 7074100 .45LB
G TRUSSJACKHANDLENUT 7074110 1.42LB
HTRUSSJACKSETSCREW3/8”X3/8” 7074120 .1LB
IJAMPLATE 7077442 .8LB
JBEARINGPLATE 7077443 1.9LB
KHINGECONE-HEADBOLT1/2”X2” 7077444 .1LB
LWASHER,FLAT,1/2”ZINC 1000800 .1LB
MNUT,1/2”,G5,ZINC 73023 .1LB
Weight
HINGED JACK PIN BARHINGEDJACKPINBAR#1 7070410 0.25LB
HINGEDJACKPINBAR#2 7070411 0.25LB
Description Item No.
TRUSS JACK HINGEDTRUSSJACKHINGED8”-12” 7070400 22LB
TRUSSJACKHINGED11”-16” 7070401 32LB
TRUSSJACKHINGED18”-24” 7070402 41LB
TRUSSJACKHINGED22”-32” 7070403 32LB
TRUSSJACKHINGED33”-50” 7070404 41LB
Use Notes/ObservationsHolds Hinged Truss Jack in place with Truss Jack Hinge Pin when Jack is in “fly” position.
Attaches to the top of the base of the A-Frame.
9
ATLAS FLY FORM SYSTEM
BUILDING HAWAII SINCE 1961
A-FRAME FLY FORM
Description Item No. Weight
Use Notes/ObservationsThe lag clip is used to attach a 2x rub rail along the outside edge of table joists to make flying proce-dure easier and to prevent edge damage to form ply and end damage to joists.
Attach t-bolt assembly to slot in joist and lag screw (by GC) to 2x rub rail
Use Notes/ObservationsUsed when trusses need to move in more than one direction in order to remove from building.
Custom item
TRUSS CASTER 7072300 12LB
LAG CLIPLAGCLIP-STEEL/ZINC 7071500 0.5LB
LAGCLIP-ALUMINUM 7071501 0.25LB
Use Notes/ObservationsUsed in typical truss flying applications to roll the truss out of the building.
3,000 lb. capacity Custom item
TRUSS ROLLER 7071800 32LB
10
Use Notes/ObservationsAttaches truss jack top casting to hinge assembly. Also holds truss jack in upright position when truss is moving or in flying form.
Used in conjunction with hinged jack pin bar
TRUSS JACK HINGE PIN 7070412 .44LB
ATLAS-SALES.COM | (808) 841-1111
ATLAS FLY FORM SYSTEM
ATLAS-SALES.COM | (808) 841-1111
A-FRAME FLY FORM
Weight
Use Notes/ObservationsProvides a simple socket for installation of a safety rail post using nominal 2x4.
Attached to truss top chord with 2-bolt clamp or to typical aluminum beam with strap clamp.
Use Notes/ObservationsAttaches A-Frame to H-750. Installs via slot at the end of H-750 to
fasten bottom of A-Frame to truss chord.
Description Item No.
Use Notes/ObservationsAttaches column-post to H-750. Commonly used for columns and items
other than A-Frames not using 2 or 3 bolt clamp.
1 BOLT CLAMP 7070700 .38LB
Use Notes/ObservationsAttaches A-Frame to H-750. Installs via slot at the end of H-750 to
fasten tops of A-Frame to truss top chord and safety rail bracket.
2 BOLT CLAMP 7070800 1LB
TRUSS SAFETY RAIL BRACKET 7071300 10.2LB
11
3 BOLT CLAMP 7070900 1.5LB
ATLAS FLY FORM SYSTEM
BUILDING HAWAII SINCE 1961
A-FRAME FLY FORM
Description Item No. Weight
Use Notes/ObservationsAttaches joist to truss chords or any other item to joists/stringers
Supplied with t-bolt assembly
Use Notes/ObservationsAttaches to bottom of top H-750 Chord and allows for connecting of wing panel where A-Frame access is not possible
TRUSS HINGE WING PANEL ASSEMBLY A071700 12LB
JOIST CLIP ASSEMBLY JCLIP .34LB
HEAVY DUTY TRUSS CROSS BRACETRUSSCROSSBRACE7X2.5 7070706 40LB
TRUSSCROSSBRACE7X4 7070707 34LB
TRUSSCROSSBRACE10X4 7070710 40LB
TRUSSCROSSBRACE12x4 7070712 46LB
TRUSSCROSSBRACE5X2.5 7070756 21LB
TRUSSCROSSBRACE10X2.5 7070730 40LB
STANDARD CROSS BRACECROSSBRACE4x4/5-WHITE BC0445 8LB
CROSSBRACE5x4/5-RED BC0545 9LB
CROSSBRACE6x4/5-ORANGE BC0645 11LB
CROSSBRACE7x4/5-YELLOW BC0745 12LB
CROSSBRACE8x4/5-BLACK BC0845 14LB
CROSSBRACE10x4/5-GREEN BC1045 16LB
Use Notes/ObservationsInternal cross support between the two side trusses of the A-Frame Table.
Use Notes/ObservationsJoins two H-750 Chords together. The use of full moment splice plates may
be necessary in areas where a stronger joint is required.
C-750 COUPLER 707110 9LB
Use Notes/ObservationsThis three piece support system strengthens the joint formed between two H-750 Chords and is nec-essary when the joint strength is required to be the same as the rest of the length of the two chords.
The bottom two plates rest in the top and bottom channel of the chords and the top plate fills the space in the middle. Held in place with 4 bolt assemblies (#72031A). Full moment splice plate assembly is always used in conjunction with the C-750 coupler.
FULL MOMENT SPLICE PLATE ASSEMBLY 7071110 5LB
Use Notes/ObservationsSet of four to hold full moment splice plate as-sembly together
Assembly includes G5 rated nut and bolt, and two washers.
BOLT ASSEMBLY 3/4”X3.50”, G5 72031A 1.75LB
Installed with two sets of the full moment splice plate as-sembly, on the top and bottom of the H-750 chord, C-750 coupler, and held in place with four (4) bolt assemblies.
Perspective of two H-750 chords being joined together with four (4) bolt assemblies
ATLAS FLY FORM SYSTEM
BUILDING HAWAII SINCE 1961
A-FRAME FLY FORM
Description Item No. Weight
Use Notes/ObservationsTo adjust the height of fly form tables when positioning
Used to lower Fly-Forms from poured position to rolling position.
Use Notes/ObservationsAttaches to top chord and is used for lifting the truss.
Second generation of fixed lifting bracket. More flexible in positions after table is built. Angled pick bar to lower stress on welds. Replaces #7071200
TRUSS LIFTING BRACKET - 2 PIECE 7071201 5LB
Use Notes/ObservationsFacilitates the lifting, placing and removal of fly form tables.
Use Notes/ObservationsServes as the main horizontal support component of the upper portion of the A-Frame truss and sup-ports the plywood decking.
Most applications will use the 6 1/2” joists, for heavy duty applications where the poured floor is particularly thick the 7 1/2” stringer is used.Please ask your sales representative about availability and recommended use.
15
Use Notes/ObservationsTo lower tall fly forms Has bi-directional rollers to facilitate 360°
movement of table
HL FLY FORM HYD. JACK DOLLIE HLFFHJD 55LB
Use Notes/ObservationsTo adjust the height of fly form tables when positioning
Used to lower Fly-Forms from poured position to rolling position.